Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/hskinnemoen/tclib into base

drivers/clocksource/Makefile

+obj-$(CONFIG_ATMEL_TCB_CLKSRC)	+= tcb_clksrc.o
 obj-$(CONFIG_X86_CYCLONE_TIMER)	+= cyclone.o
 obj-$(CONFIG_X86_PM_TIMER)	+= acpi_pm.o
 obj-$(CONFIG_SCx200HR_TIMER)	+= scx200_hrt.o

drivers/clocksource/tcb_clksrc.c

+#include <linux/init.h>
+#include <linux/clocksource.h>
+#include <linux/clockchips.h>
+#include <linux/interrupt.h>
+#include <linux/irq.h>
+
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/ioport.h>
+#include <linux/io.h>
+#include <linux/platform_device.h>
+#include <linux/atmel_tc.h>
+
+
+/*
+ * We're configured to use a specific TC block, one that's not hooked
+ * up to external hardware, to provide a time solution:
+ *
+ *   - Two channels combine to create a free-running 32 bit counter
+ *     with a base rate of 5+ MHz, packaged as a clocksource (with
+ *     resolution better than 200 nsec).
+ *
+ *   - The third channel may be used to provide a 16-bit clockevent
+ *     source, used in either periodic or oneshot mode.  This runs
+ *     at 32 KiHZ, and can handle delays of up to two seconds.
+ *
+ * A boot clocksource and clockevent source are also currently needed,
+ * unless the relevant platforms (ARM/AT91, AVR32/AT32) are changed so
+ * this code can be used when init_timers() is called, well before most
+ * devices are set up.  (Some low end AT91 parts, which can run uClinux,
+ * have only the timers in one TC block... they currently don't support
+ * the tclib code, because of that initialization issue.)
+ *
+ * REVISIT behavior during system suspend states... we should disable
+ * all clocks and save the power.  Easily done for clockevent devices,
+ * but clocksources won't necessarily get the needed notifications.
+ * For deeper system sleep states, this will be mandatory...
+ */
+
+static void __iomem *tcaddr;
+
+static cycle_t tc_get_cycles(void)
+{
+	unsigned long	flags;
+	u32		lower, upper;
+
+	raw_local_irq_save(flags);
+	do {
+		upper = __raw_readl(tcaddr + ATMEL_TC_REG(1, CV));
+		lower = __raw_readl(tcaddr + ATMEL_TC_REG(0, CV));
+	} while (upper != __raw_readl(tcaddr + ATMEL_TC_REG(1, CV)));
+
+	raw_local_irq_restore(flags);
+	return (upper << 16) | lower;
+}
+
+static struct clocksource clksrc = {
+	.name           = "tcb_clksrc",
+	.rating         = 200,
+	.read           = tc_get_cycles,
+	.mask           = CLOCKSOURCE_MASK(32),
+	.shift          = 18,
+	.flags		= CLOCK_SOURCE_IS_CONTINUOUS,
+};
+
+#ifdef CONFIG_GENERIC_CLOCKEVENTS
+
+struct tc_clkevt_device {
+	struct clock_event_device	clkevt;
+	struct clk			*clk;
+	void __iomem			*regs;
+};
+
+static struct tc_clkevt_device *to_tc_clkevt(struct clock_event_device *clkevt)
+{
+	return container_of(clkevt, struct tc_clkevt_device, clkevt);
+}
+
+/* For now, we always use the 32K clock ... this optimizes for NO_HZ,
+ * because using one of the divided clocks would usually mean the
+ * tick rate can never be less than several dozen Hz (vs 0.5 Hz).
+ *
+ * A divided clock could be good for high resolution timers, since
+ * 30.5 usec resolution can seem "low".
+ */
+static u32 timer_clock;
+
+static void tc_mode(enum clock_event_mode m, struct clock_event_device *d)
+{
+	struct tc_clkevt_device *tcd = to_tc_clkevt(d);
+	void __iomem		*regs = tcd->regs;
+
+	if (tcd->clkevt.mode == CLOCK_EVT_MODE_PERIODIC
+			|| tcd->clkevt.mode == CLOCK_EVT_MODE_ONESHOT) {
+		__raw_writel(0xff, regs + ATMEL_TC_REG(2, IDR));
+		__raw_writel(ATMEL_TC_CLKDIS, regs + ATMEL_TC_REG(2, CCR));
+		clk_disable(tcd->clk);
+	}
+
+	switch (m) {
+
+	/* By not making the gentime core emulate periodic mode on top
+	 * of oneshot, we get lower overhead and improved accuracy.
+	 */
+	case CLOCK_EVT_MODE_PERIODIC:
+		clk_enable(tcd->clk);
+
+		/* slow clock, count up to RC, then irq and restart */
+		__raw_writel(timer_clock
+				| ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+				regs + ATMEL_TC_REG(2, CMR));
+		__raw_writel((32768 + HZ/2) / HZ, tcaddr + ATMEL_TC_REG(2, RC));
+
+		/* Enable clock and interrupts on RC compare */
+		__raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+		/* go go gadget! */
+		__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+				regs + ATMEL_TC_REG(2, CCR));
+		break;
+
+	case CLOCK_EVT_MODE_ONESHOT:
+		clk_enable(tcd->clk);
+
+		/* slow clock, count up to RC, then irq and stop */
+		__raw_writel(timer_clock | ATMEL_TC_CPCSTOP
+				| ATMEL_TC_WAVE | ATMEL_TC_WAVESEL_UP_AUTO,
+				regs + ATMEL_TC_REG(2, CMR));
+		__raw_writel(ATMEL_TC_CPCS, regs + ATMEL_TC_REG(2, IER));
+
+		/* set_next_event() configures and starts the timer */
+		break;
+
+	default:
+		break;
+	}
+}
+
+static int tc_next_event(unsigned long delta, struct clock_event_device *d)
+{
+	__raw_writel(delta, tcaddr + ATMEL_TC_REG(2, RC));
+
+	/* go go gadget! */
+	__raw_writel(ATMEL_TC_CLKEN | ATMEL_TC_SWTRG,
+			tcaddr + ATMEL_TC_REG(2, CCR));
+	return 0;
+}
+
+static struct tc_clkevt_device clkevt = {
+	.clkevt	= {
+		.name		= "tc_clkevt",
+		.features	= CLOCK_EVT_FEAT_PERIODIC
+					| CLOCK_EVT_FEAT_ONESHOT,
+		.shift		= 32,
+		/* Should be lower than at91rm9200's system timer */
+		.rating		= 125,
+		.cpumask	= CPU_MASK_CPU0,
+		.set_next_event	= tc_next_event,
+		.set_mode	= tc_mode,
+	},
+};
+
+static irqreturn_t ch2_irq(int irq, void *handle)
+{
+	struct tc_clkevt_device	*dev = handle;
+	unsigned int		sr;
+
+	sr = __raw_readl(dev->regs + ATMEL_TC_REG(2, SR));
+	if (sr & ATMEL_TC_CPCS) {
+		dev->clkevt.event_handler(&dev->clkevt);
+		return IRQ_HANDLED;
+	}
+
+	return IRQ_NONE;
+}
+
+static struct irqaction tc_irqaction = {
+	.name		= "tc_clkevt",
+	.flags		= IRQF_TIMER | IRQF_DISABLED,
+	.handler	= ch2_irq,
+};
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+	struct clk *t2_clk = tc->clk[2];
+	int irq = tc->irq[2];
+
+	clkevt.regs = tc->regs;
+	clkevt.clk = t2_clk;
+	tc_irqaction.dev_id = &clkevt;
+
+	timer_clock = clk32k_divisor_idx;
+
+	clkevt.clkevt.mult = div_sc(32768, NSEC_PER_SEC, clkevt.clkevt.shift);
+	clkevt.clkevt.max_delta_ns
+		= clockevent_delta2ns(0xffff, &clkevt.clkevt);
+	clkevt.clkevt.min_delta_ns = clockevent_delta2ns(1, &clkevt.clkevt) + 1;
+
+	setup_irq(irq, &tc_irqaction);
+
+	clockevents_register_device(&clkevt.clkevt);
+}
+
+#else /* !CONFIG_GENERIC_CLOCKEVENTS */
+
+static void __init setup_clkevents(struct atmel_tc *tc, int clk32k_divisor_idx)
+{
+	/* NOTHING */
+}
+
+#endif
+
+static int __init tcb_clksrc_init(void)
+{
+	static char bootinfo[] __initdata
+		= KERN_DEBUG "%s: tc%d at %d.%03d MHz\n";
+
+	struct platform_device *pdev;
+	struct atmel_tc *tc;
+	struct clk *t0_clk;
+	u32 rate, divided_rate = 0;
+	int best_divisor_idx = -1;
+	int clk32k_divisor_idx = -1;
+	int i;
+
+	tc = atmel_tc_alloc(CONFIG_ATMEL_TCB_CLKSRC_BLOCK, clksrc.name);
+	if (!tc) {
+		pr_debug("can't alloc TC for clocksource\n");
+		return -ENODEV;
+	}
+	tcaddr = tc->regs;
+	pdev = tc->pdev;
+
+	t0_clk = tc->clk[0];
+	clk_enable(t0_clk);
+
+	/* How fast will we be counting?  Pick something over 5 MHz.  */
+	rate = (u32) clk_get_rate(t0_clk);
+	for (i = 0; i < 5; i++) {
+		unsigned divisor = atmel_tc_divisors[i];
+		unsigned tmp;
+
+		/* remember 32 KiHz clock for later */
+		if (!divisor) {
+			clk32k_divisor_idx = i;
+			continue;
+		}
+
+		tmp = rate / divisor;
+		pr_debug("TC: %u / %-3u [%d] --> %u\n", rate, divisor, i, tmp);
+		if (best_divisor_idx > 0) {
+			if (tmp < 5 * 1000 * 1000)
+				continue;
+		}
+		divided_rate = tmp;
+		best_divisor_idx = i;
+	}
+
+	clksrc.mult = clocksource_hz2mult(divided_rate, clksrc.shift);
+
+	printk(bootinfo, clksrc.name, CONFIG_ATMEL_TCB_CLKSRC_BLOCK,
+			divided_rate / 1000000,
+			((divided_rate + 500000) % 1000000) / 1000);
+
+	/* tclib will give us three clocks no matter what the
+	 * underlying platform supports.
+	 */
+	clk_enable(tc->clk[1]);
+
+	/* channel 0:  waveform mode, input mclk/8, clock TIOA0 on overflow */
+	__raw_writel(best_divisor_idx			/* likely divide-by-8 */
+			| ATMEL_TC_WAVE
+			| ATMEL_TC_WAVESEL_UP		/* free-run */
+			| ATMEL_TC_ACPA_SET		/* TIOA0 rises at 0 */
+			| ATMEL_TC_ACPC_CLEAR,		/* (duty cycle 50%) */
+			tcaddr + ATMEL_TC_REG(0, CMR));
+	__raw_writel(0x0000, tcaddr + ATMEL_TC_REG(0, RA));
+	__raw_writel(0x8000, tcaddr + ATMEL_TC_REG(0, RC));
+	__raw_writel(0xff, tcaddr + ATMEL_TC_REG(0, IDR));	/* no irqs */
+	__raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(0, CCR));
+
+	/* channel 1:  waveform mode, input TIOA0 */
+	__raw_writel(ATMEL_TC_XC1			/* input: TIOA0 */
+			| ATMEL_TC_WAVE
+			| ATMEL_TC_WAVESEL_UP,		/* free-run */
+			tcaddr + ATMEL_TC_REG(1, CMR));
+	__raw_writel(0xff, tcaddr + ATMEL_TC_REG(1, IDR));	/* no irqs */
+	__raw_writel(ATMEL_TC_CLKEN, tcaddr + ATMEL_TC_REG(1, CCR));
+
+	/* chain channel 0 to channel 1, then reset all the timers */
+	__raw_writel(ATMEL_TC_TC1XC1S_TIOA0, tcaddr + ATMEL_TC_BMR);
+	__raw_writel(ATMEL_TC_SYNC, tcaddr + ATMEL_TC_BCR);
+
+	/* and away we go! */
+	clocksource_register(&clksrc);
+
+	/* channel 2:  periodic and oneshot timer support */
+	setup_clkevents(tc, clk32k_divisor_idx);
+
+	return 0;
+}
+arch_initcall(tcb_clksrc_init);

drivers/misc/Kconfig

@@ -22,6 +22,39 @@ config ATMEL_PWM
 	  purposes including software controlled power-efficent backlights
 	  on LCD displays, motor control, and waveform generation.
 
+config ATMEL_TCLIB
+	bool "Atmel AT32/AT91 Timer/Counter Library"
+	depends on (AVR32 || ARCH_AT91)
+	help
+	  Select this if you want a library to allocate the Timer/Counter
+	  blocks found on many Atmel processors.  This facilitates using
+	  these blocks by different drivers despite processor differences.
+
+config ATMEL_TCB_CLKSRC
+	bool "TC Block Clocksource"
+	depends on ATMEL_TCLIB && GENERIC_TIME
+	default y
+	help
+	  Select this to get a high precision clocksource based on a
+	  TC block with a 5+ MHz base clock rate.  Two timer channels
+	  are combined to make a single 32-bit timer.
+
+	  When GENERIC_CLOCKEVENTS is defined, the third timer channel
+	  may be used as a clock event device supporting oneshot mode
+	  (delays of up to two seconds) based on the 32 KiHz clock.
+
+config ATMEL_TCB_CLKSRC_BLOCK
+	int
+	depends on ATMEL_TCB_CLKSRC
+	prompt "TC Block" if ARCH_AT91RM9200 || ARCH_AT91SAM9260 || CPU_AT32AP700X
+	default 0
+	range 0 1
+	help
+	  Some chips provide more than one TC block, so you have the
+	  choice of which one to use for the clock framework.  The other
+	  TC can be used for other purposes, such as PWM generation and
+	  interval timing.
+
 config IBM_ASM
 	tristate "Device driver for IBM RSA service processor"
 	depends on X86 && PCI && INPUT && EXPERIMENTAL

drivers/misc/Makefile

@@ -10,6 +10,7 @@ obj-$(CONFIG_ACER_WMI)     += acer-wmi.o
 obj-$(CONFIG_ASUS_LAPTOP)     += asus-laptop.o
 obj-$(CONFIG_ATMEL_PWM)		+= atmel_pwm.o
 obj-$(CONFIG_ATMEL_SSC)		+= atmel-ssc.o
+obj-$(CONFIG_ATMEL_TCLIB)	+= atmel_tclib.o
 obj-$(CONFIG_TC1100_WMI)	+= tc1100-wmi.o
 obj-$(CONFIG_LKDTM)		+= lkdtm.o
 obj-$(CONFIG_TIFM_CORE)       	+= tifm_core.o

drivers/misc/atmel_tclib.c

+#include <linux/atmel_tc.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/init.h>
+#include <linux/io.h>
+#include <linux/ioport.h>
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+/* Number of bytes to reserve for the iomem resource */
+#define ATMEL_TC_IOMEM_SIZE	256
+
+
+/*
+ * This is a thin library to solve the problem of how to portably allocate
+ * one of the TC blocks.  For simplicity, it doesn't currently expect to
+ * share individual timers between different drivers.
+ */
+
+#if defined(CONFIG_AVR32)
+/* AVR32 has these divide PBB */
+const u8 atmel_tc_divisors[5] = { 0, 4, 8, 16, 32, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#elif defined(CONFIG_ARCH_AT91)
+/* AT91 has these divide MCK */
+const u8 atmel_tc_divisors[5] = { 2, 8, 32, 128, 0, };
+EXPORT_SYMBOL(atmel_tc_divisors);
+
+#endif
+
+static DEFINE_SPINLOCK(tc_list_lock);
+static LIST_HEAD(tc_list);
+
+/**
+ * atmel_tc_alloc - allocate a specified TC block
+ * @block: which block to allocate
+ * @name: name to be associated with the iomem resource
+ *
+ * Caller allocates a block.  If it is available, a pointer to a
+ * pre-initialized struct atmel_tc is returned. The caller can access
+ * the registers directly through the "regs" field.
+ */
+struct atmel_tc *atmel_tc_alloc(unsigned block, const char *name)
+{
+	struct atmel_tc		*tc;
+	struct platform_device	*pdev = NULL;
+	struct resource		*r;
+
+	spin_lock(&tc_list_lock);
+	list_for_each_entry(tc, &tc_list, node) {
+		if (tc->pdev->id == block) {
+			pdev = tc->pdev;
+			break;
+		}
+	}
+
+	if (!pdev || tc->iomem)
+		goto fail;
+
+	r = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	r = request_mem_region(r->start, ATMEL_TC_IOMEM_SIZE, name);
+	if (!r)
+		goto fail;
+
+	tc->regs = ioremap(r->start, ATMEL_TC_IOMEM_SIZE);
+	if (!tc->regs)
+		goto fail_ioremap;
+
+	tc->iomem = r;
+
+out:
+	spin_unlock(&tc_list_lock);
+	return tc;
+
+fail_ioremap:
+	release_resource(r);
+fail:
+	tc = NULL;
+	goto out;
+}
+EXPORT_SYMBOL_GPL(atmel_tc_alloc);
+
+/**
+ * atmel_tc_free - release a specified TC block
+ * @tc: Timer/counter block that was returned by atmel_tc_alloc()
+ *
+ * This reverses the effect of atmel_tc_alloc(), unmapping the I/O
+ * registers, invalidating the resource returned by that routine and
+ * making the TC available to other drivers.
+ */
+void atmel_tc_free(struct atmel_tc *tc)
+{
+	spin_lock(&tc_list_lock);
+	if (tc->regs) {
+		iounmap(tc->regs);
+		release_resource(tc->iomem);
+		tc->regs = NULL;
+		tc->iomem = NULL;
+	}
+	spin_unlock(&tc_list_lock);
+}
+EXPORT_SYMBOL_GPL(atmel_tc_free);
+
+static int __init tc_probe(struct platform_device *pdev)
+{
+	struct atmel_tc *tc;
+	struct clk	*clk;
+	int		irq;
+
+	if (!platform_get_resource(pdev, IORESOURCE_MEM, 0))
+		return -EINVAL;
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0)
+		return -EINVAL;
+
+	tc = kzalloc(sizeof(struct atmel_tc), GFP_KERNEL);
+	if (!tc)
+		return -ENOMEM;
+
+	tc->pdev = pdev;
+
+	clk = clk_get(&pdev->dev, "t0_clk");
+	if (IS_ERR(clk)) {
+		kfree(tc);
+		return -EINVAL;
+	}
+
+	tc->clk[0] = clk;
+	tc->clk[1] = clk_get(&pdev->dev, "t1_clk");
+	if (IS_ERR(tc->clk[1]))
+		tc->clk[1] = clk;
+	tc->clk[2] = clk_get(&pdev->dev, "t2_clk");
+	if (IS_ERR(tc->clk[2]))
+		tc->clk[2] = clk;
+
+	tc->irq[0] = irq;
+	tc->irq[1] = platform_get_irq(pdev, 1);
+	if (tc->irq[1] < 0)
+		tc->irq[1] = irq;
+	tc->irq[2] = platform_get_irq(pdev, 2);
+	if (tc->irq[2] < 0)
+		tc->irq[2] = irq;
+
+	spin_lock(&tc_list_lock);
+	list_add_tail(&tc->node, &tc_list);
+	spin_unlock(&tc_list_lock);
+
+	return 0;
+}
+
+static struct platform_driver tc_driver = {
+	.driver.name	= "atmel_tcb",
+};
+
+static int __init tc_init(void)
+{
+	return platform_driver_probe(&tc_driver, tc_probe);
+}
+arch_initcall(tc_init);