gigaset: fix device ERROR response handling

Clear out pending command that got rejected with 'ERROR' response.
This fixes the bug where unloading the driver module would hang
with the message: "gigaset: not searching scheduled commands: busy"
after a device communication error.

Impact: error handling bugfix
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/isdn/gigaset/ev-layer.c

@@ -207,7 +207,6 @@ struct reply_t gigaset_tab_nocid[] =
 	/* leave dle mode */
 	{RSP_INIT,      0,  0,SEQ_DLE0,           201, 5, {0},             "^SDLE=0\r"},
 	{RSP_OK,      201,201, -1,                202,-1},
-	//{RSP_ZDLE,    202,202,  0,                202, 0, {ACT_ERROR}},//DELETE
 	{RSP_ZDLE,    202,202,  0,                  0, 0, {ACT_DLE0}},
 	{RSP_NODEV,   200,249, -1,                  0, 0, {ACT_FAKEDLE0}},
 	{RSP_ERROR,   200,249, -1,                  0, 0, {ACT_FAILDLE0}},
@@ -265,6 +264,7 @@ struct reply_t gigaset_tab_nocid[] =
 	{EV_SHUTDOWN,  -1, -1, -1,                 -1,-1, {ACT_SHUTDOWN}}, //FIXME
 
 	/* misc. */
+	{RSP_ERROR,    -1, -1, -1,                 -1, -1, {ACT_ERROR} },
 	{RSP_EMPTY,    -1, -1, -1,                 -1,-1, {ACT_DEBUG}}, //FIXME
 	{RSP_ZCFGT,    -1, -1, -1,                 -1,-1, {ACT_DEBUG}}, //FIXME
 	{RSP_ZCFG,     -1, -1, -1,                 -1,-1, {ACT_DEBUG}}, //FIXME
@@ -328,10 +328,9 @@ struct reply_t gigaset_tab_cid[] =
 	{RSP_INIT,     -1, -1,SEQ_HUP,            401, 5, {0},             "+VLS=0\r"}, /* hang up */ //-1,-1?
 	{RSP_OK,      401,401, -1,                402, 5},
 	{RSP_ZVLS,    402,402,  0,                403, 5},
-	{RSP_ZSAU,    403,403,ZSAU_DISCONNECT_REQ, -1,-1, {ACT_DEBUG}}, /* if not remote hup */
-	//{RSP_ZSAU,    403,403,ZSAU_NULL,          401, 0, {ACT_ERROR}}, //DELETE//FIXME -> DLE0 // should we do this _before_ hanging up for base driver?
-	{RSP_ZSAU,    403,403,ZSAU_NULL,            0, 0, {ACT_DISCONNECT}}, //FIXME -> DLE0 // should we do this _before_ hanging up for base driver?
-	{RSP_NODEV,   401,403, -1,                  0, 0, {ACT_FAKEHUP}}, //FIXME -> DLE0 // should we do this _before_ hanging up for base driver?
+	{RSP_ZSAU,    403, 403, ZSAU_DISCONNECT_REQ, -1, -1, {ACT_DEBUG} },
+	{RSP_ZSAU,    403, 403, ZSAU_NULL,            0,  0, {ACT_DISCONNECT} },
+	{RSP_NODEV,   401, 403, -1,                   0,  0, {ACT_FAKEHUP} },
 	{RSP_ERROR,   401,401, -1,                  0, 0, {ACT_ABORTHUP}},
 	{EV_TIMEOUT,  401,403, -1,                  0, 0, {ACT_ABORTHUP}},
 
@@ -1434,11 +1433,12 @@ static void do_action(int action, struct cardstate *cs,
 		cs->gotfwver = -1;
 		dev_err(cs->dev, "could not read firmware version.\n");
 		break;
-#ifdef CONFIG_GIGASET_DEBUG
 	case ACT_ERROR:
-		*p_genresp = 1;
-		*p_resp_code = RSP_ERROR;
+		gig_dbg(DEBUG_ANY, "%s: ERROR response in ConState %d",
+			__func__, at_state->ConState);
+		cs->cur_at_seq = SEQ_NONE;
 		break;
+#ifdef CONFIG_GIGASET_DEBUG
 	case ACT_TEST:
 		{
 			static int count = 3; //2; //1;