Commit 06822788 authored by Vinod Koul's avatar Vinod Koul

Merge branch 'topic/xilinx' into for-linus

parents 3c814be9 9cd4360d
Xilinx AXI VDMA engine, it does transfers between memory and video devices.
It can be configured to have one channel or two channels. If configured
as two channels, one is to transmit to the video device and another is
to receive from the video device.
Required properties:
- compatible: Should be "xlnx,axi-vdma-1.00.a"
- #dma-cells: Should be <1>, see "dmas" property below
- reg: Should contain VDMA registers location and length.
- xlnx,num-fstores: Should be the number of framebuffers as configured in h/w.
- dma-channel child node: Should have at least one channel and can have up to
two channels per device. This node specifies the properties of each
DMA channel (see child node properties below).
Optional properties:
- xlnx,include-sg: Tells configured for Scatter-mode in
the hardware.
- xlnx,flush-fsync: Tells which channel to Flush on Frame sync.
It takes following values:
{1}, flush both channels
{2}, flush mm2s channel
{3}, flush s2mm channel
Required child node properties:
- compatible: It should be either "xlnx,axi-vdma-mm2s-channel" or
"xlnx,axi-vdma-s2mm-channel".
- interrupts: Should contain per channel VDMA interrupts.
- xlnx,data-width: Should contain the stream data width, take values
{32,64...1024}.
Optional child node properties:
- xlnx,include-dre: Tells hardware is configured for Data
Realignment Engine.
- xlnx,genlock-mode: Tells Genlock synchronization is
enabled/disabled in hardware.
Example:
++++++++
axi_vdma_0: axivdma@40030000 {
compatible = "xlnx,axi-vdma-1.00.a";
#dma_cells = <1>;
reg = < 0x40030000 0x10000 >;
xlnx,num-fstores = <0x8>;
xlnx,flush-fsync = <0x1>;
dma-channel@40030000 {
compatible = "xlnx,axi-vdma-mm2s-channel";
interrupts = < 0 54 4 >;
xlnx,datawidth = <0x40>;
} ;
dma-channel@40030030 {
compatible = "xlnx,axi-vdma-s2mm-channel";
interrupts = < 0 53 4 >;
xlnx,datawidth = <0x40>;
} ;
} ;
* DMA client
Required properties:
- dmas: a list of <[Video DMA device phandle] [Channel ID]> pairs,
where Channel ID is '0' for write/tx and '1' for read/rx
channel.
- dma-names: a list of DMA channel names, one per "dmas" entry
Example:
++++++++
vdmatest_0: vdmatest@0 {
compatible ="xlnx,axi-vdma-test-1.00.a";
dmas = <&axi_vdma_0 0
&axi_vdma_0 1>;
dma-names = "vdma0", "vdma1";
} ;
...@@ -361,6 +361,20 @@ config FSL_EDMA ...@@ -361,6 +361,20 @@ config FSL_EDMA
multiplexing capability for DMA request sources(slot). multiplexing capability for DMA request sources(slot).
This module can be found on Freescale Vybrid and LS-1 SoCs. This module can be found on Freescale Vybrid and LS-1 SoCs.
config XILINX_VDMA
tristate "Xilinx AXI VDMA Engine"
depends on (ARCH_ZYNQ || MICROBLAZE)
select DMA_ENGINE
help
Enable support for Xilinx AXI VDMA Soft IP.
This engine provides high-bandwidth direct memory access
between memory and AXI4-Stream video type target
peripherals including peripherals which support AXI4-
Stream Video Protocol. It has two stream interfaces/
channels, Memory Mapped to Stream (MM2S) and Stream to
Memory Mapped (S2MM) for the data transfers.
config DMA_ENGINE config DMA_ENGINE
bool bool
......
...@@ -46,3 +46,4 @@ obj-$(CONFIG_K3_DMA) += k3dma.o ...@@ -46,3 +46,4 @@ obj-$(CONFIG_K3_DMA) += k3dma.o
obj-$(CONFIG_MOXART_DMA) += moxart-dma.o obj-$(CONFIG_MOXART_DMA) += moxart-dma.o
obj-$(CONFIG_FSL_EDMA) += fsl-edma.o obj-$(CONFIG_FSL_EDMA) += fsl-edma.o
obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o obj-$(CONFIG_QCOM_BAM_DMA) += qcom_bam_dma.o
obj-y += xilinx/
obj-$(CONFIG_XILINX_VDMA) += xilinx_vdma.o
This diff is collapsed.
/*
* Xilinx DMA Engine drivers support header file
*
* Copyright (C) 2010-2014 Xilinx, Inc. All rights reserved.
*
* This is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __DMA_XILINX_DMA_H
#define __DMA_XILINX_DMA_H
#include <linux/dma-mapping.h>
#include <linux/dmaengine.h>
/**
* struct xilinx_vdma_config - VDMA Configuration structure
* @frm_dly: Frame delay
* @gen_lock: Whether in gen-lock mode
* @master: Master that it syncs to
* @frm_cnt_en: Enable frame count enable
* @park: Whether wants to park
* @park_frm: Frame to park on
* @coalesc: Interrupt coalescing threshold
* @delay: Delay counter
* @reset: Reset Channel
* @ext_fsync: External Frame Sync source
*/
struct xilinx_vdma_config {
int frm_dly;
int gen_lock;
int master;
int frm_cnt_en;
int park;
int park_frm;
int coalesc;
int delay;
int reset;
int ext_fsync;
};
int xilinx_vdma_channel_set_config(struct dma_chan *dchan,
struct xilinx_vdma_config *cfg);
#endif
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment