Commit 071cf249 authored by Aniroop Mathur's avatar Aniroop Mathur Committed by Jonathan Cameron

IIO: Change msleep to usleep_range for small msecs

msleep(1~20) may not do what the caller intends, and will often sleep longer.
(~20 ms actual sleep for any value given in the 1~20ms range)
This is not the desired behaviour for many cases like device resume time,
device suspend time, device enable time, data reading time, etc.
Thus, change msleep to usleep_range for precise wakeups.
Signed-off-by: default avatarAniroop Mathur <a.mathur@samsung.com>
Signed-off-by: default avatarJonathan Cameron <jic23@kernel.org>
parent 160d9587
......@@ -632,7 +632,7 @@ static irqreturn_t exynos_ts_isr(int irq, void *dev_id)
input_report_key(info->input, BTN_TOUCH, 1);
input_sync(info->input);
msleep(1);
usleep_range(1000, 1100);
};
writel(0, ADC_V1_CLRINTPNDNUP(info->regs));
......
......@@ -65,7 +65,7 @@ struct bmp280_data {
struct bmp180_calib calib;
struct regulator *vddd;
struct regulator *vdda;
unsigned int start_up_time; /* in milliseconds */
unsigned int start_up_time; /* in microseconds */
/* log of base 2 of oversampling rate */
u8 oversampling_press;
......@@ -935,14 +935,14 @@ int bmp280_common_probe(struct device *dev,
data->chip_info = &bmp180_chip_info;
data->oversampling_press = ilog2(8);
data->oversampling_temp = ilog2(1);
data->start_up_time = 10;
data->start_up_time = 10000;
break;
case BMP280_CHIP_ID:
indio_dev->num_channels = 2;
data->chip_info = &bmp280_chip_info;
data->oversampling_press = ilog2(16);
data->oversampling_temp = ilog2(2);
data->start_up_time = 2;
data->start_up_time = 2000;
break;
case BME280_CHIP_ID:
indio_dev->num_channels = 3;
......@@ -950,7 +950,7 @@ int bmp280_common_probe(struct device *dev,
data->oversampling_press = ilog2(16);
data->oversampling_humid = ilog2(16);
data->oversampling_temp = ilog2(2);
data->start_up_time = 2;
data->start_up_time = 2000;
break;
default:
return -EINVAL;
......@@ -979,7 +979,7 @@ int bmp280_common_probe(struct device *dev,
goto out_disable_vddd;
}
/* Wait to make sure we started up properly */
mdelay(data->start_up_time);
usleep_range(data->start_up_time, data->start_up_time + 100);
/* Bring chip out of reset if there is an assigned GPIO line */
gpiod = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
......@@ -1038,7 +1038,7 @@ int bmp280_common_probe(struct device *dev,
* Set autosuspend to two orders of magnitude larger than the
* start-up time.
*/
pm_runtime_set_autosuspend_delay(dev, data->start_up_time *100);
pm_runtime_set_autosuspend_delay(dev, data->start_up_time / 10);
pm_runtime_use_autosuspend(dev);
pm_runtime_put(dev);
......@@ -1101,7 +1101,7 @@ static int bmp280_runtime_resume(struct device *dev)
ret = regulator_enable(data->vdda);
if (ret)
return ret;
msleep(data->start_up_time);
usleep_range(data->start_up_time, data->start_up_time + 100);
return data->chip_info->chip_config(data);
}
#endif /* CONFIG_PM */
......
......@@ -377,7 +377,7 @@ static int ade7753_initial_setup(struct iio_dev *indio_dev)
}
ade7753_reset(dev);
msleep(ADE7753_STARTUP_DELAY);
usleep_range(ADE7753_STARTUP_DELAY, ADE7753_STARTUP_DELAY + 100);
err_ret:
return ret;
......
......@@ -49,7 +49,7 @@
#define ADE7753_MAX_TX 4
#define ADE7753_MAX_RX 4
#define ADE7753_STARTUP_DELAY 1
#define ADE7753_STARTUP_DELAY 1000
#define ADE7753_SPI_SLOW (u32)(300 * 1000)
#define ADE7753_SPI_BURST (u32)(1000 * 1000)
......
......@@ -389,7 +389,7 @@ static int ade7754_initial_setup(struct iio_dev *indio_dev)
}
ade7754_reset(dev);
msleep(ADE7754_STARTUP_DELAY);
usleep_range(ADE7754_STARTUP_DELAY, ADE7754_STARTUP_DELAY + 100);
err_ret:
return ret;
......
......@@ -67,7 +67,7 @@
#define ADE7754_MAX_TX 4
#define ADE7754_MAX_RX 4
#define ADE7754_STARTUP_DELAY 1
#define ADE7754_STARTUP_DELAY 1000
#define ADE7754_SPI_SLOW (u32)(300 * 1000)
#define ADE7754_SPI_BURST (u32)(1000 * 1000)
......
......@@ -89,7 +89,7 @@
#define ADE7758_MAX_TX 8
#define ADE7758_MAX_RX 4
#define ADE7758_STARTUP_DELAY 1
#define ADE7758_STARTUP_DELAY 1000
#define AD7758_NUM_WAVSEL 5
#define AD7758_NUM_PHSEL 3
......
......@@ -459,7 +459,7 @@ static int ade7758_initial_setup(struct iio_dev *indio_dev)
}
ade7758_reset(dev);
msleep(ADE7758_STARTUP_DELAY);
usleep_range(ADE7758_STARTUP_DELAY, ADE7758_STARTUP_DELAY + 100);
err_ret:
return ret;
......
......@@ -338,7 +338,7 @@ static int ade7759_initial_setup(struct iio_dev *indio_dev)
}
ade7759_reset(dev);
msleep(ADE7759_STARTUP_DELAY);
usleep_range(ADE7759_STARTUP_DELAY, ADE7759_STARTUP_DELAY + 100);
err_ret:
return ret;
......
......@@ -30,7 +30,7 @@
#define ADE7759_MAX_TX 6
#define ADE7759_MAX_RX 6
#define ADE7759_STARTUP_DELAY 1
#define ADE7759_STARTUP_DELAY 1000
#define ADE7759_SPI_SLOW (u32)(300 * 1000)
#define ADE7759_SPI_BURST (u32)(1000 * 1000)
......
......@@ -444,7 +444,7 @@ static int ade7854_initial_setup(struct iio_dev *indio_dev)
}
ade7854_reset(dev);
msleep(ADE7854_STARTUP_DELAY);
usleep_range(ADE7854_STARTUP_DELAY, ADE7854_STARTUP_DELAY + 100);
err_ret:
return ret;
......
......@@ -136,7 +136,7 @@
#define ADE7854_MAX_TX 7
#define ADE7854_MAX_RX 7
#define ADE7854_STARTUP_DELAY 1
#define ADE7854_STARTUP_DELAY 1000
#define ADE7854_SPI_SLOW (u32)(300 * 1000)
#define ADE7854_SPI_BURST (u32)(1000 * 1000)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment