ARM: dts: qcom: Use "pcie" as the node name instead of "pci"

Qcom SoCs doesn't support the legacy PCI, but only PCIe. So use the correct
node name for the controller instances.
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Link: https://lore.kernel.org/r/20231206135540.17068-2-manivannan.sadhasivam@linaro.orgSigned-off-by: Bjorn Andersson <andersson@kernel.org>

arch/arm/boot/dts/qcom/qcom-apq8064.dtsi

@@ -1284,7 +1284,7 @@ gfx3d1: iommu@7d00000 {
 			qcom,ncb = <3>;
 		};
 
-		pcie: pci@1b500000 {
+		pcie: pcie@1b500000 {
 			compatible = "qcom,pcie-apq8064";
 			reg = <0x1b500000 0x1000>,
 			      <0x1b502000 0x80>,

arch/arm/boot/dts/qcom/qcom-ipq4019-ap.dk04.1.dtsi

@@ -98,7 +98,7 @@ flash@0 {
 			};
 		};
 
-		pci@40000000 {
+		pcie@40000000 {
 			status = "okay";
 			perst-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
 		};

arch/arm/boot/dts/qcom/qcom-ipq4019.dtsi

@@ -417,7 +417,7 @@ restart@4ab000 {
 			reg = <0x4ab000 0x4>;
 		};
 
-		pcie0: pci@40000000 {
+		pcie0: pcie@40000000 {
 			compatible = "qcom,pcie-ipq4019";
 			reg = <0x40000000 0xf1d>,
 			      <0x40000f20 0xa8>,

arch/arm/boot/dts/qcom/qcom-ipq8064.dtsi

@@ -1076,7 +1076,7 @@ sata_phy: sata-phy@1b400000 {
 			status = "disabled";
 		};
 
-		pcie0: pci@1b500000 {
+		pcie0: pcie@1b500000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b500000 0x1000
 			       0x1b502000 0x80
@@ -1127,7 +1127,7 @@ pcie0: pci@1b500000 {
 			perst-gpios = <&qcom_pinmux 3 GPIO_ACTIVE_LOW>;
 		};
 
-		pcie1: pci@1b700000 {
+		pcie1: pcie@1b700000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b700000 0x1000
 			       0x1b702000 0x80
@@ -1178,7 +1178,7 @@ pcie1: pci@1b700000 {
 			perst-gpios = <&qcom_pinmux 48 GPIO_ACTIVE_LOW>;
 		};
 
-		pcie2: pci@1b900000 {
+		pcie2: pcie@1b900000 {
 			compatible = "qcom,pcie-ipq8064";
 			reg = <0x1b900000 0x1000
 			       0x1b902000 0x80