Commit 0ca6e000 authored by David S. Miller's avatar David S. Miller

Merge branch 'ns2-amac'

Jon Mason says:

====================
add NS2 support to bgmac

Changes in v6:
* Use a common bgmac_phy_connect_direct (per Rafal Milecki)
* Rebased on latest net-next
* Added Reviewed-by to the relevant patches

Changes in v5:
* Change a pr_err to netdev_err (per Scott Branden)
* Reword the lane swap binding documentation (per Andrew Lunn)

Changes in v4:
* Actually send out the lane swap binding doc patch (Per Scott Branden)
* Remove unused #define (Per Andrew Lunn)

Changes in v3:
* Clean-up the bgmac DT binding doc (per Rob Herring)
* Document the lane swap binding and make it generic (Per Andrew Lunn)

Changes in v2:
* Remove the PHY power-on (per Andrew Lunn)
* Misc PHY clean-ups regarding comments and #defines (per Andrew Lunn)
  This results on none of the original PHY code from Vikas being
  present.  So, I'm removing him as an author and giving him
  "Inspired-by" credit.
* Move PHY lane swapping to PHY driver (per Andrew Lunn and Florian
  Fainelli)
* Remove bgmac sleep (per Florian Fainelli)
* Re-add bgmac chip reset (per Florian Fainelli and Ray Jui)
* Rebased on latest net-next
* Added patch for bcm54xx_auxctl_read, which is used in the BCM54810
====================
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parents 94edc86b dddc3c9d
......@@ -2,11 +2,17 @@ Broadcom AMAC Ethernet Controller Device Tree Bindings
-------------------------------------------------------------
Required properties:
- compatible: "brcm,amac" or "brcm,nsp-amac"
- reg: Address and length of the GMAC registers,
Address and length of the GMAC IDM registers
- reg-names: Names of the registers. Must have both "amac_base" and
"idm_base"
- compatible: "brcm,amac"
"brcm,nsp-amac"
"brcm,ns2-amac"
- reg: Address and length of the register set for the device. It
contains the information of registers in the same order as
described by reg-names
- reg-names: Names of the registers.
"amac_base": Address and length of the GMAC registers
"idm_base": Address and length of the GMAC IDM registers
"nicpm_base": Address and length of the NIC Port Manager
registers (required for Northstar2)
- interrupts: Interrupt number
Optional properties:
......
......@@ -35,6 +35,10 @@ Optional Properties:
- broken-turn-around: If set, indicates the PHY device does not correctly
release the turn around line low at the end of a MDIO transaction.
- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to
compensate for the board being designed with the lanes swapped.
Example:
ethernet-phy@0 {
......
......@@ -56,6 +56,10 @@ memory {
};
};
&enet {
status = "ok";
};
&pci_phy0 {
status = "ok";
};
......@@ -174,6 +178,7 @@ nandcs@0 {
&mdio_mux_iproc {
mdio@10 {
gphy0: eth-phy@10 {
enet-phy-lane-swap;
reg = <0x10>;
};
};
......
......@@ -191,6 +191,18 @@ soc: soc {
#include "ns2-clock.dtsi"
enet: ethernet@61000000 {
compatible = "brcm,ns2-amac";
reg = <0x61000000 0x1000>,
<0x61090000 0x1000>,
<0x61030000 0x100>;
reg-names = "amac_base", "idm_base", "nicpm_base";
interrupts = <GIC_SPI 341 IRQ_TYPE_LEVEL_HIGH>;
phy-handle = <&gphy0>;
phy-mode = "rgmii";
status = "disabled";
};
dma0: dma@61360000 {
compatible = "arm,pl330", "arm,primecell";
reg = <0x61360000 0x1000>;
......
......@@ -80,6 +80,24 @@ static void bcma_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset, u32 mask,
bcma_maskset32(bgmac->bcma.cmn, offset, mask, set);
}
static int bcma_phy_connect(struct bgmac *bgmac)
{
struct phy_device *phy_dev;
char bus_id[MII_BUS_ID_SIZE + 3];
/* Connect to the PHY */
snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
bgmac->phyaddr);
phy_dev = phy_connect(bgmac->net_dev, bus_id, bgmac_adjust_link,
PHY_INTERFACE_MODE_MII);
if (IS_ERR(phy_dev)) {
dev_err(bgmac->dev, "PHY connection failed\n");
return PTR_ERR(phy_dev);
}
return 0;
}
static const struct bcma_device_id bgmac_bcma_tbl[] = {
BCMA_CORE(BCMA_MANUF_BCM, BCMA_CORE_4706_MAC_GBIT,
BCMA_ANY_REV, BCMA_ANY_CLASS),
......@@ -275,6 +293,10 @@ static int bgmac_probe(struct bcma_device *core)
bgmac->cco_ctl_maskset = bcma_bgmac_cco_ctl_maskset;
bgmac->get_bus_clock = bcma_bgmac_get_bus_clock;
bgmac->cmn_maskset32 = bcma_bgmac_cmn_maskset32;
if (bgmac->mii_bus)
bgmac->phy_connect = bcma_phy_connect;
else
bgmac->phy_connect = bgmac_phy_connect_direct;
err = bgmac_enet_probe(bgmac);
if (err)
......
......@@ -14,11 +14,21 @@
#define pr_fmt(fmt) KBUILD_MODNAME ": " fmt
#include <linux/bcma/bcma.h>
#include <linux/brcmphy.h>
#include <linux/etherdevice.h>
#include <linux/of_address.h>
#include <linux/of_mdio.h>
#include <linux/of_net.h>
#include "bgmac.h"
#define NICPM_IOMUX_CTRL 0x00000008
#define NICPM_IOMUX_CTRL_INIT_VAL 0x3196e000
#define NICPM_IOMUX_CTRL_SPD_SHIFT 10
#define NICPM_IOMUX_CTRL_SPD_10M 0
#define NICPM_IOMUX_CTRL_SPD_100M 1
#define NICPM_IOMUX_CTRL_SPD_1000M 2
static u32 platform_bgmac_read(struct bgmac *bgmac, u16 offset)
{
return readl(bgmac->plat.base + offset);
......@@ -86,6 +96,54 @@ static void platform_bgmac_cmn_maskset32(struct bgmac *bgmac, u16 offset,
WARN_ON(1);
}
static void bgmac_nicpm_speed_set(struct net_device *net_dev)
{
struct bgmac *bgmac = netdev_priv(net_dev);
u32 val;
if (!bgmac->plat.nicpm_base)
return;
val = NICPM_IOMUX_CTRL_INIT_VAL;
switch (bgmac->net_dev->phydev->speed) {
default:
netdev_err(net_dev, "Unsupported speed. Defaulting to 1000Mb\n");
case SPEED_1000:
val |= NICPM_IOMUX_CTRL_SPD_1000M << NICPM_IOMUX_CTRL_SPD_SHIFT;
break;
case SPEED_100:
val |= NICPM_IOMUX_CTRL_SPD_100M << NICPM_IOMUX_CTRL_SPD_SHIFT;
break;
case SPEED_10:
val |= NICPM_IOMUX_CTRL_SPD_10M << NICPM_IOMUX_CTRL_SPD_SHIFT;
break;
}
writel(val, bgmac->plat.nicpm_base + NICPM_IOMUX_CTRL);
bgmac_adjust_link(bgmac->net_dev);
}
static int platform_phy_connect(struct bgmac *bgmac)
{
struct phy_device *phy_dev;
if (bgmac->plat.nicpm_base)
phy_dev = of_phy_get_and_connect(bgmac->net_dev,
bgmac->dev->of_node,
bgmac_nicpm_speed_set);
else
phy_dev = of_phy_get_and_connect(bgmac->net_dev,
bgmac->dev->of_node,
bgmac_adjust_link);
if (!phy_dev) {
dev_err(bgmac->dev, "PHY connection failed\n");
return -ENODEV;
}
return 0;
}
static int bgmac_probe(struct platform_device *pdev)
{
struct device_node *np = pdev->dev.of_node;
......@@ -102,7 +160,6 @@ static int bgmac_probe(struct platform_device *pdev)
/* Set the features of the 4707 family */
bgmac->feature_flags |= BGMAC_FEAT_CLKCTLST;
bgmac->feature_flags |= BGMAC_FEAT_NO_RESET;
bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
bgmac->feature_flags |= BGMAC_FEAT_CMDCFG_SR_REV4;
bgmac->feature_flags |= BGMAC_FEAT_TX_MASK_SETUP;
bgmac->feature_flags |= BGMAC_FEAT_RX_MASK_SETUP;
......@@ -142,6 +199,14 @@ static int bgmac_probe(struct platform_device *pdev)
if (IS_ERR(bgmac->plat.idm_base))
return PTR_ERR(bgmac->plat.idm_base);
regs = platform_get_resource_byname(pdev, IORESOURCE_MEM, "nicpm_base");
if (regs) {
bgmac->plat.nicpm_base = devm_ioremap_resource(&pdev->dev,
regs);
if (IS_ERR(bgmac->plat.nicpm_base))
return PTR_ERR(bgmac->plat.nicpm_base);
}
bgmac->read = platform_bgmac_read;
bgmac->write = platform_bgmac_write;
bgmac->idm_read = platform_bgmac_idm_read;
......@@ -151,6 +216,12 @@ static int bgmac_probe(struct platform_device *pdev)
bgmac->cco_ctl_maskset = platform_bgmac_cco_ctl_maskset;
bgmac->get_bus_clock = platform_bgmac_get_bus_clock;
bgmac->cmn_maskset32 = platform_bgmac_cmn_maskset32;
if (of_parse_phandle(np, "phy-handle", 0)) {
bgmac->phy_connect = platform_phy_connect;
} else {
bgmac->phy_connect = bgmac_phy_connect_direct;
bgmac->feature_flags |= BGMAC_FEAT_FORCE_SPEED_2500;
}
return bgmac_enet_probe(bgmac);
}
......@@ -167,6 +238,7 @@ static int bgmac_remove(struct platform_device *pdev)
static const struct of_device_id bgmac_of_enet_match[] = {
{.compatible = "brcm,amac",},
{.compatible = "brcm,nsp-amac",},
{.compatible = "brcm,ns2-amac",},
{},
};
......
......@@ -1082,6 +1082,9 @@ static void bgmac_enable(struct bgmac *bgmac)
/* http://bcm-v4.sipsolutions.net/mac-gbit/gmac/chipinit */
static void bgmac_chip_init(struct bgmac *bgmac)
{
/* Clear any erroneously pending interrupts */
bgmac_write(bgmac, BGMAC_INT_STATUS, ~0);
/* 1 interrupt per received frame */
bgmac_write(bgmac, BGMAC_INT_RECV_LAZY, 1 << BGMAC_IRL_FC_SHIFT);
......@@ -1388,7 +1391,7 @@ static const struct ethtool_ops bgmac_ethtool_ops = {
* MII
**************************************************/
static void bgmac_adjust_link(struct net_device *net_dev)
void bgmac_adjust_link(struct net_device *net_dev)
{
struct bgmac *bgmac = netdev_priv(net_dev);
struct phy_device *phy_dev = net_dev->phydev;
......@@ -1411,8 +1414,9 @@ static void bgmac_adjust_link(struct net_device *net_dev)
phy_print_status(phy_dev);
}
}
EXPORT_SYMBOL_GPL(bgmac_adjust_link);
static int bgmac_phy_connect_direct(struct bgmac *bgmac)
int bgmac_phy_connect_direct(struct bgmac *bgmac)
{
struct fixed_phy_status fphy_status = {
.link = 1,
......@@ -1437,24 +1441,7 @@ static int bgmac_phy_connect_direct(struct bgmac *bgmac)
return err;
}
static int bgmac_phy_connect(struct bgmac *bgmac)
{
struct phy_device *phy_dev;
char bus_id[MII_BUS_ID_SIZE + 3];
/* Connect to the PHY */
snprintf(bus_id, sizeof(bus_id), PHY_ID_FMT, bgmac->mii_bus->id,
bgmac->phyaddr);
phy_dev = phy_connect(bgmac->net_dev, bus_id, &bgmac_adjust_link,
PHY_INTERFACE_MODE_MII);
if (IS_ERR(phy_dev)) {
dev_err(bgmac->dev, "PHY connection failed\n");
return PTR_ERR(phy_dev);
}
return 0;
}
EXPORT_SYMBOL_GPL(bgmac_phy_connect_direct);
int bgmac_enet_probe(struct bgmac *info)
{
......@@ -1507,9 +1494,6 @@ int bgmac_enet_probe(struct bgmac *info)
netif_napi_add(net_dev, &bgmac->napi, bgmac_poll, BGMAC_WEIGHT);
if (!bgmac->mii_bus)
err = bgmac_phy_connect_direct(bgmac);
else
err = bgmac_phy_connect(bgmac);
if (err) {
dev_err(bgmac->dev, "Cannot connect to phy\n");
......
......@@ -463,6 +463,7 @@ struct bgmac {
struct {
void *base;
void *idm_base;
void *nicpm_base;
} plat;
struct {
struct bcma_device *core;
......@@ -513,10 +514,13 @@ struct bgmac {
u32 (*get_bus_clock)(struct bgmac *bgmac);
void (*cmn_maskset32)(struct bgmac *bgmac, u16 offset, u32 mask,
u32 set);
int (*phy_connect)(struct bgmac *bgmac);
};
int bgmac_enet_probe(struct bgmac *info);
void bgmac_enet_remove(struct bgmac *bgmac);
void bgmac_adjust_link(struct net_device *net_dev);
int bgmac_phy_connect_direct(struct bgmac *bgmac);
struct mii_bus *bcma_mdio_mii_register(struct bcma_device *core, u8 phyaddr);
void bcma_mdio_mii_unregister(struct mii_bus *mii_bus);
......@@ -583,4 +587,9 @@ static inline void bgmac_set(struct bgmac *bgmac, u16 offset, u32 set)
{
bgmac_maskset(bgmac, offset, ~0, set);
}
static inline int bgmac_phy_connect(struct bgmac *bgmac)
{
return bgmac->phy_connect(bgmac);
}
#endif /* _BGMAC_H */
......@@ -217,7 +217,7 @@ config BROADCOM_PHY
select BCM_NET_PHYLIB
---help---
Currently supports the BCM5411, BCM5421, BCM5461, BCM54616S, BCM5464,
BCM5481 and BCM5482 PHYs.
BCM5481, BCM54810 and BCM5482 PHYs.
config CICADA_PHY
tristate "Cicada PHYs"
......
......@@ -18,7 +18,7 @@
#include <linux/module.h>
#include <linux/phy.h>
#include <linux/brcmphy.h>
#include <linux/of.h>
#define BRCM_PHY_MODEL(phydev) \
((phydev)->drv->phy_id & (phydev)->drv->phy_id_mask)
......@@ -30,11 +30,49 @@ MODULE_DESCRIPTION("Broadcom PHY driver");
MODULE_AUTHOR("Maciej W. Rozycki");
MODULE_LICENSE("GPL");
static int bcm54xx_auxctl_read(struct phy_device *phydev, u16 regnum)
{
/* The register must be written to both the Shadow Register Select and
* the Shadow Read Register Selector
*/
phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum |
regnum << MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT);
return phy_read(phydev, MII_BCM54XX_AUX_CTL);
}
static int bcm54xx_auxctl_write(struct phy_device *phydev, u16 regnum, u16 val)
{
return phy_write(phydev, MII_BCM54XX_AUX_CTL, regnum | val);
}
static int bcm54810_config(struct phy_device *phydev)
{
int rc, val;
val = bcm_phy_read_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL);
val &= ~BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN;
rc = bcm_phy_write_exp(phydev, BCM54810_EXP_BROADREACH_LRE_MISC_CTL,
val);
if (rc < 0)
return rc;
val = bcm54xx_auxctl_read(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC);
val &= ~MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN;
val |= MII_BCM54XX_AUXCTL_MISC_WREN;
rc = bcm54xx_auxctl_write(phydev, MII_BCM54XX_AUXCTL_SHDWSEL_MISC,
val);
if (rc < 0)
return rc;
val = bcm_phy_read_shadow(phydev, BCM54810_SHD_CLK_CTL);
val &= ~BCM54810_SHD_CLK_CTL_GTXCLK_EN;
rc = bcm_phy_write_shadow(phydev, BCM54810_SHD_CLK_CTL, val);
if (rc < 0)
return rc;
return 0;
}
/* Needs SMDSP clock enabled via bcm54xx_phydsp_config() */
static int bcm50610_a0_workaround(struct phy_device *phydev)
{
......@@ -207,6 +245,12 @@ static int bcm54xx_config_init(struct phy_device *phydev)
(phydev->dev_flags & PHY_BRCM_AUTO_PWRDWN_ENABLE))
bcm54xx_adjust_rxrefclk(phydev);
if (BRCM_PHY_MODEL(phydev) == PHY_ID_BCM54810) {
err = bcm54810_config(phydev);
if (err)
return err;
}
bcm54xx_phydsp_config(phydev);
return 0;
......@@ -304,6 +348,7 @@ static int bcm5482_read_status(struct phy_device *phydev)
static int bcm5481_config_aneg(struct phy_device *phydev)
{
struct device_node *np = phydev->mdio.dev.of_node;
int ret;
/* Aneg firsly. */
......@@ -334,6 +379,14 @@ static int bcm5481_config_aneg(struct phy_device *phydev)
phy_write(phydev, 0x18, reg);
}
if (of_property_read_bool(np, "enet-phy-lane-swap")) {
/* Lane Swap - Undocumented register...magic! */
ret = bcm_phy_write_exp(phydev, MII_BCM54XX_EXP_SEL_ER + 0x9,
0x11B);
if (ret < 0)
return ret;
}
return ret;
}
......@@ -567,6 +620,18 @@ static struct phy_driver broadcom_drivers[] = {
.read_status = genphy_read_status,
.ack_interrupt = bcm_phy_ack_intr,
.config_intr = bcm_phy_config_intr,
}, {
.phy_id = PHY_ID_BCM54810,
.phy_id_mask = 0xfffffff0,
.name = "Broadcom BCM54810",
.features = PHY_GBIT_FEATURES |
SUPPORTED_Pause | SUPPORTED_Asym_Pause,
.flags = PHY_HAS_MAGICANEG | PHY_HAS_INTERRUPT,
.config_init = bcm54xx_config_init,
.config_aneg = bcm5481_config_aneg,
.read_status = genphy_read_status,
.ack_interrupt = bcm_phy_ack_intr,
.config_intr = bcm_phy_config_intr,
}, {
.phy_id = PHY_ID_BCM5482,
.phy_id_mask = 0xfffffff0,
......@@ -651,6 +716,7 @@ static struct mdio_device_id __maybe_unused broadcom_tbl[] = {
{ PHY_ID_BCM54616S, 0xfffffff0 },
{ PHY_ID_BCM5464, 0xfffffff0 },
{ PHY_ID_BCM5481, 0xfffffff0 },
{ PHY_ID_BCM54810, 0xfffffff0 },
{ PHY_ID_BCM5482, 0xfffffff0 },
{ PHY_ID_BCM50610, 0xfffffff0 },
{ PHY_ID_BCM50610M, 0xfffffff0 },
......
......@@ -13,6 +13,7 @@
#define PHY_ID_BCM5241 0x0143bc30
#define PHY_ID_BCMAC131 0x0143bc70
#define PHY_ID_BCM5481 0x0143bca0
#define PHY_ID_BCM54810 0x03625d00
#define PHY_ID_BCM5482 0x0143bcb0
#define PHY_ID_BCM5411 0x00206070
#define PHY_ID_BCM5421 0x002060e0
......@@ -56,6 +57,7 @@
#define PHY_BRCM_EXT_IBND_TX_ENABLE 0x00002000
#define PHY_BRCM_CLEAR_RGMII_MODE 0x00004000
#define PHY_BRCM_DIS_TXCRXC_NOENRGY 0x00008000
/* Broadcom BCM7xxx specific workarounds */
#define PHY_BRCM_7XXX_REV(x) (((x) >> 8) & 0xff)
#define PHY_BRCM_7XXX_PATCH(x) ((x) & 0xff)
......@@ -110,6 +112,8 @@
#define MII_BCM54XX_AUXCTL_MISC_FORCE_AMDIX 0x0200
#define MII_BCM54XX_AUXCTL_MISC_RDSEL_MISC 0x7000
#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC 0x0007
#define MII_BCM54XX_AUXCTL_SHDWSEL_READ_SHIFT 12
#define MII_BCM54XX_AUXCTL_SHDWSEL_MISC_RGMII_SKEW_EN (1 << 8)
#define MII_BCM54XX_AUXCTL_SHDWSEL_MASK 0x0007
......@@ -191,6 +195,12 @@
#define BCM5482_SSD_SGMII_SLAVE_EN 0x0002 /* Slave mode enable */
#define BCM5482_SSD_SGMII_SLAVE_AD 0x0001 /* Slave auto-detection */
/* BCM54810 Registers */
#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL (MII_BCM54XX_EXP_SEL_ER + 0x90)
#define BCM54810_EXP_BROADREACH_LRE_MISC_CTL_EN (1 << 0)
#define BCM54810_SHD_CLK_CTL 0x3
#define BCM54810_SHD_CLK_CTL_GTXCLK_EN (1 << 9)
/*****************************************************************************/
/* Fast Ethernet Transceiver definitions. */
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment