Commit 0e9fd777 authored by Enric Balletbo i Serra's avatar Enric Balletbo i Serra Committed by Tony Lindgren

ARM: dts: omap3-igep: Add support for LBEE1USJYC WiFi connected to SDIO

The LBEE1USJYC is a WiFi/BT combo module used on OMAP3-based IGEP boards. In
both cases, IGEPv2 Rev. C and IGEP COM MODULE, the module is connected using
the same MMC interface and uses the same GPIOs.
Signed-off-by: default avatarEnric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: default avatarTony Lindgren <tony@atomide.com>
parent 8559133d
...@@ -24,6 +24,25 @@ sound { ...@@ -24,6 +24,25 @@ sound {
ti,mcbsp = <&mcbsp2>; ti,mcbsp = <&mcbsp2>;
ti,codec = <&twl_audio>; ti,codec = <&twl_audio>;
}; };
vdd33: regulator-vdd33 {
compatible = "regulator-fixed";
regulator-name = "vdd33";
regulator-always-on;
};
lbee1usjyc_vmmc: lbee1usjyc_vmmc {
pinctrl-names = "default";
pinctrl-0 = <&lbee1usjyc_pins>;
compatible = "regulator-fixed";
regulator-name = "regulator-lbee1usjyc";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
gpio = <&gpio5 10 GPIO_ACTIVE_HIGH>; /* gpio_138 WIFI_PDN */
startup-delay-us = <10000>;
enable-active-high;
vin-supply = <&vdd33>;
};
}; };
&omap3_pmx_core { &omap3_pmx_core {
...@@ -48,6 +67,15 @@ uart3_pins: pinmux_uart3_pins { ...@@ -48,6 +67,15 @@ uart3_pins: pinmux_uart3_pins {
>; >;
}; };
/* WiFi/BT combo */
lbee1usjyc_pins: pinmux_lbee1usjyc_pins {
pinctrl-single,pins = <
0x136 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat5.gpio_137 */
0x138 (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat6.gpio_138 */
0x13a (PIN_OUTPUT | MUX_MODE4) /* sdmmc2_dat7.gpio_139 */
>;
};
mcbsp2_pins: pinmux_mcbsp2_pins { mcbsp2_pins: pinmux_mcbsp2_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */ 0x10c (PIN_INPUT | MUX_MODE0) /* mcbsp2_fsx.mcbsp2_fsx */
...@@ -68,6 +96,17 @@ mmc1_pins: pinmux_mmc1_pins { ...@@ -68,6 +96,17 @@ mmc1_pins: pinmux_mmc1_pins {
>; >;
}; };
mmc2_pins: pinmux_mmc2_pins {
pinctrl-single,pins = <
0x128 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_clk.sdmmc2_clk */
0x12a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_cmd.sdmmc2_cmd */
0x12c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat0.sdmmc2_dat0 */
0x12e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat1.sdmmc2_dat1 */
0x130 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat2.sdmmc2_dat2 */
0x132 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc2_dat3.sdmmc2_dat3 */
>;
};
smsc911x_pins: pinmux_smsc911x_pins { smsc911x_pins: pinmux_smsc911x_pins {
pinctrl-single,pins = < pinctrl-single,pins = <
0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */ 0x1a2 (PIN_INPUT | MUX_MODE4) /* mcspi1_cs2.gpio_176 */
...@@ -114,7 +153,11 @@ &mmc1 { ...@@ -114,7 +153,11 @@ &mmc1 {
}; };
&mmc2 { &mmc2 {
status = "disabled"; pinctrl-names = "default";
pinctrl-0 = <&mmc2_pins>;
vmmc-supply = <&lbee1usjyc_vmmc>;
bus-width = <4>;
non-removable;
}; };
&mmc3 { &mmc3 {
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment