Commit 131b3de7 authored by Linus Walleij's avatar Linus Walleij Committed by Dmitry Torokhov

Input: add D-Link DIR-685 touchkeys driver

This adds support for the D-Link DIR-685 touchkeys found in the
router with this name.

The vendor code calles this a "touchpad" but we are registering
it here under its real name.
Signed-off-by: default avatarLinus Walleij <linus.walleij@linaro.org>
Acked-by: default avatarRob Herring <robh@kernel.org>
Signed-off-by: default avatarDmitry Torokhov <dmitry.torokhov@gmail.com>
parent 086cebfa
* D-Link DIR-685 Touchkeys
This is a I2C one-off touchkey controller based on the Cypress Semiconductor
CY8C214 MCU with some firmware in its internal 8KB flash. The circuit
board inside the router is named E119921.
The touchkey device node should be placed inside an I2C bus node.
Required properties:
- compatible: must be "dlink,dir685-touchkeys"
- reg: the I2C address of the touchkeys
- interrupts: reference to the interrupt number
Example:
touchkeys@26 {
compatible = "dlink,dir685-touchkeys";
reg = <0x26>;
interrupt-parent = <&gpio0>;
interrupts = <17 IRQ_TYPE_EDGE_FALLING>;
};
......@@ -3786,6 +3786,12 @@ S: Supported
F: drivers/input/touchscreen/cyttsp*
F: include/linux/input/cyttsp.h
D-LINK DIR-685 TOUCHKEYS DRIVER
M: Linus Walleij <linus.walleij@linaro.org>
L: linux-input@vger.kernel.org
S: Supported
F: drivers/input/dlink-dir685-touchkeys.c
DALLAS/MAXIM DS1685-FAMILY REAL TIME CLOCK
M: Joshua Kinard <kumba@gentoo.org>
S: Maintained
......
......@@ -178,6 +178,17 @@ config KEYBOARD_CLPS711X
To compile this driver as a module, choose M here: the
module will be called clps711x-keypad.
config KEYBOARD_DLINK_DIR685
tristate "D-Link DIR-685 touchkeys support"
depends on I2C
default ARCH_GEMINI
help
If you say yes here you get support for the D-Link DIR-685
touchkeys.
To compile this driver as a module, choose M here: the
module will be called dlink-dir685-touchkeys.
config KEYBOARD_LKKBD
tristate "DECstation/VAXstation LK201/LK401 keyboard"
select SERIO
......
......@@ -17,6 +17,7 @@ obj-$(CONFIG_KEYBOARD_CAP11XX) += cap11xx.o
obj-$(CONFIG_KEYBOARD_CLPS711X) += clps711x-keypad.o
obj-$(CONFIG_KEYBOARD_CROS_EC) += cros_ec_keyb.o
obj-$(CONFIG_KEYBOARD_DAVINCI) += davinci_keyscan.o
obj-$(CONFIG_KEYBOARD_DLINK_DIR685) += dlink-dir685-touchkeys.o
obj-$(CONFIG_KEYBOARD_EP93XX) += ep93xx_keypad.o
obj-$(CONFIG_KEYBOARD_GOLDFISH_EVENTS) += goldfish_events.o
obj-$(CONFIG_KEYBOARD_GPIO) += gpio_keys.o
......
/*
* D-Link DIR-685 router I2C-based Touchkeys input driver
* Copyright (C) 2017 Linus Walleij <linus.walleij@linaro.org>
*
* This is a one-off touchkey controller based on the Cypress Semiconductor
* CY8C214 MCU with some firmware in its internal 8KB flash. The circuit
* board inside the router is named E119921
*/
#include <linux/module.h>
#include <linux/i2c.h>
#include <linux/interrupt.h>
#include <linux/delay.h>
#include <linux/input.h>
#include <linux/slab.h>
#include <linux/bitops.h>
struct dir685_touchkeys {
struct device *dev;
struct i2c_client *client;
struct input_dev *input;
unsigned long cur_key;
u16 codes[7];
};
static irqreturn_t dir685_tk_irq_thread(int irq, void *data)
{
struct dir685_touchkeys *tk = data;
const int num_bits = min_t(int, ARRAY_SIZE(tk->codes), 16);
unsigned long changed;
u8 buf[6];
unsigned long key;
int i;
int err;
memset(buf, 0, sizeof(buf));
err = i2c_master_recv(tk->client, buf, sizeof(buf));
if (err != sizeof(buf)) {
dev_err(tk->dev, "short read %d\n", err);
return IRQ_HANDLED;
}
dev_dbg(tk->dev, "IN: %*ph\n", (int)sizeof(buf), buf);
key = be16_to_cpup((__be16 *) &buf[4]);
/* Figure out if any bits went high or low since last message */
changed = tk->cur_key ^ key;
for_each_set_bit(i, &changed, num_bits) {
dev_dbg(tk->dev, "key %d is %s\n", i,
test_bit(i, &key) ? "down" : "up");
input_report_key(tk->input, tk->codes[i], test_bit(i, &key));
}
/* Store currently down keys */
tk->cur_key = key;
input_sync(tk->input);
return IRQ_HANDLED;
}
static int dir685_tk_probe(struct i2c_client *client,
const struct i2c_device_id *id)
{
struct dir685_touchkeys *tk;
struct device *dev = &client->dev;
u8 bl_data[] = { 0xa7, 0x40 };
int err;
int i;
tk = devm_kzalloc(&client->dev, sizeof(*tk), GFP_KERNEL);
if (!tk)
return -ENOMEM;
tk->input = devm_input_allocate_device(dev);
if (!tk->input)
return -ENOMEM;
tk->client = client;
tk->dev = dev;
tk->input->keycodesize = sizeof(u16);
tk->input->keycodemax = ARRAY_SIZE(tk->codes);
tk->input->keycode = tk->codes;
tk->codes[0] = KEY_UP;
tk->codes[1] = KEY_DOWN;
tk->codes[2] = KEY_LEFT;
tk->codes[3] = KEY_RIGHT;
tk->codes[4] = KEY_ENTER;
tk->codes[5] = KEY_WPS_BUTTON;
/*
* This key appears in the vendor driver, but I have
* not been able to activate it.
*/
tk->codes[6] = KEY_RESERVED;
__set_bit(EV_KEY, tk->input->evbit);
for (i = 0; i < ARRAY_SIZE(tk->codes); i++)
__set_bit(tk->codes[i], tk->input->keybit);
__clear_bit(KEY_RESERVED, tk->input->keybit);
tk->input->name = "D-Link DIR-685 touchkeys";
tk->input->id.bustype = BUS_I2C;
err = input_register_device(tk->input);
if (err)
return err;
/* Set the brightness to max level */
err = i2c_master_send(client, bl_data, sizeof(bl_data));
if (err != sizeof(bl_data))
dev_warn(tk->dev, "error setting brightness level\n");
if (!client->irq) {
dev_err(dev, "no IRQ on the I2C device\n");
return -ENODEV;
}
err = devm_request_threaded_irq(dev, client->irq,
NULL, dir685_tk_irq_thread,
IRQF_ONESHOT,
"dir685-tk", tk);
if (err) {
dev_err(dev, "can't request IRQ\n");
return err;
}
return 0;
}
static const struct i2c_device_id dir685_tk_id[] = {
{ "dir685tk", 0 },
{ }
};
MODULE_DEVICE_TABLE(i2c, dir685_tk_id);
#ifdef CONFIG_OF
static const struct of_device_id dir685_tk_of_match[] = {
{ .compatible = "dlink,dir685-touchkeys" },
{},
};
MODULE_DEVICE_TABLE(of, dir685_tk_of_match);
#endif
static struct i2c_driver dir685_tk_i2c_driver = {
.driver = {
.name = "dlin-dir685-touchkeys",
.of_match_table = of_match_ptr(dir685_tk_of_match),
},
.probe = dir685_tk_probe,
.id_table = dir685_tk_id,
};
module_i2c_driver(dir685_tk_i2c_driver);
MODULE_AUTHOR("Linus Walleij <linus.walleij@linaro.org>");
MODULE_DESCRIPTION("D-Link DIR-685 touchkeys driver");
MODULE_LICENSE("GPL");
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment