Commit 1642bf66 authored by Sebastian Reichel's avatar Sebastian Reichel Committed by Heiko Stuebner

arm64: dts: rockchip: add USB2 to rk3588s-rock5a

Enable USB2 (EHCI and OCHI mode) support for the Radxa ROCK 5 Model A.
This adds USB support for the on-board WLAN/BT chip, the two USB2
ports, the USB available from the 2x20 connector and the lower USB3
port (in USB2 mode).

The upper USB3 (further away from the PCB) uses the RK3588S USB TypeC
OTG controller for USB2 and USB3 and thus is not supported at all at
the moment.
Signed-off-by: default avatarSebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20230712165106.65603-5-sebastian.reichel@collabora.comSigned-off-by: default avatarHeiko Stuebner <heiko@sntech.de>
parent 488fc7ad
......@@ -64,6 +64,20 @@ vcc12v_dcin: vcc12v-dcin-regulator {
regulator-max-microvolt = <12000000>;
};
vcc5v0_host: vcc5v0-host-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_host";
regulator-boot-on;
regulator-always-on;
regulator-min-microvolt = <5000000>;
regulator-max-microvolt = <5000000>;
enable-active-high;
gpio = <&gpio4 RK_PB5 GPIO_ACTIVE_HIGH>;
pinctrl-names = "default";
pinctrl-0 = <&vcc5v0_host_en>;
vin-supply = <&vcc5v0_sys>;
};
vcc5v0_sys: vcc5v0-sys-regulator {
compatible = "regulator-fixed";
regulator-name = "vcc5v0_sys";
......@@ -292,6 +306,34 @@ rtl8211f_rst: rtl8211f-rst {
rockchip,pins = <3 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
usb {
vcc5v0_host_en: vcc5v0-host-en {
rockchip,pins = <4 RK_PB5 RK_FUNC_GPIO &pcfg_pull_none>;
};
};
wifibt {
wl_reset: wl-reset {
rockchip,pins = <0 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
};
wl_dis: wl-dis {
rockchip,pins = <0 RK_PD5 RK_FUNC_GPIO &pcfg_output_high>;
};
wl_wake_host: wl-wake-host {
rockchip,pins = <0 RK_PC7 RK_FUNC_GPIO &pcfg_pull_up>;
};
bt_dis: bt-dis {
rockchip,pins = <0 RK_PD4 RK_FUNC_GPIO &pcfg_output_high>;
};
bt_wake_host: bt-wake-host {
rockchip,pins = <0 RK_PC5 RK_FUNC_GPIO &pcfg_pull_up>;
};
};
};
&pwm3 {
......@@ -650,7 +692,43 @@ regulator-state-mem {
};
};
&u2phy2 {
status = "okay";
};
&u2phy2_host {
status = "okay";
phy-supply = <&vcc5v0_host>;
};
&u2phy3 {
status = "okay";
};
&u2phy3_host {
phy-supply = <&vcc5v0_host>;
status = "okay";
};
&uart2 {
pinctrl-0 = <&uart2m0_xfer>;
status = "okay";
};
&usb_host0_ehci {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&wl_reset &wl_dis &wl_wake_host &bt_dis &bt_wake_host>;
};
&usb_host0_ohci {
status = "okay";
};
&usb_host1_ehci {
status = "okay";
};
&usb_host1_ohci {
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment