net: phy: correct format of block comments

Block comments should not use a trailing */ on a separate line and every
line of a block comment should start with an '*'.
Signed-off-by: Wenpeng Liang <liangwenpeng@huawei.com>
Signed-off-by: Weihang Li <liweihang@huawei.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/phy/national.c

@@ -68,7 +68,8 @@ static int ns_ack_interrupt(struct phy_device *phydev)
 		return ret;
 
 	/* Clear the interrupt status bit by writing a “1”
-	 * to the corresponding bit in INT_CLEAR (2:0 are reserved) */
+	 * to the corresponding bit in INT_CLEAR (2:0 are reserved)
+	 */
 	ret = phy_write(phydev, DP83865_INT_CLEAR, ret & ~0x7);
 
 	return ret;
@@ -150,7 +151,8 @@ static int ns_config_init(struct phy_device *phydev)
 {
 	ns_giga_speed_fallback(phydev, ALL_FALLBACK_ON);
 	/* In the latest MAC or switches design, the 10 Mbps loopback
-	   is desired to be turned off. */
+	 * is desired to be turned off.
+	 */
 	ns_10_base_t_hdx_loopack(phydev, hdx_loopback_off);
 	return ns_ack_interrupt(phydev);
 }

drivers/net/phy/phy-core.c

@@ -76,7 +76,8 @@ EXPORT_SYMBOL_GPL(phy_duplex_to_str);
 
 /* A mapping of all SUPPORTED settings to speed/duplex.  This table
  * must be grouped by speed and sorted in descending match priority
- * - iow, descending speed. */
+ * - iow, descending speed.
+ */
 
 #define PHY_SETTING(s, d, b) { .speed = SPEED_ ## s, .duplex = DUPLEX_ ## d, \
 			       .bit = ETHTOOL_LINK_MODE_ ## b ## _BIT}

drivers/net/phy/phylink.c

@@ -182,7 +182,8 @@ static int phylink_parse_fixedlink(struct phylink *pl,
 			pl->link_config.duplex = DUPLEX_FULL;
 
 		/* We treat the "pause" and "asym-pause" terminology as
-		 * defining the link partner's ability. */
+		 * defining the link partner's ability.
+		 */
 		if (fwnode_property_read_bool(fixed_node, "pause"))
 			__set_bit(ETHTOOL_LINK_MODE_Pause_BIT,
 				  pl->link_config.lp_advertising);
@@ -685,7 +686,8 @@ static void phylink_resolve(struct work_struct *w)
 			phylink_mac_pcs_get_state(pl, &link_state);
 
 			/* If we have a phy, the "up" state is the union of
-			 * both the PHY and the MAC */
+			 * both the PHY and the MAC
+			 */
 			if (pl->phydev)
 				link_state.link &= pl->phy_state.link;
 
@@ -694,7 +696,8 @@ static void phylink_resolve(struct work_struct *w)
 				link_state.interface = pl->phy_state.interface;
 
 				/* If we have a PHY, we need to update with
-				 * the PHY flow control bits. */
+				 * the PHY flow control bits.
+				 */
 				link_state.pause = pl->phy_state.pause;
 				mac_config = true;
 			}

drivers/net/phy/vitesse.c

@@ -249,7 +249,8 @@ static int vsc73xx_config_aneg(struct phy_device *phydev)
 
 /* This adds a skew for both TX and RX clocks, so the skew should only be
  * applied to "rgmii-id" interfaces. It may not work as expected
- * on "rgmii-txid", "rgmii-rxid" or "rgmii" interfaces. */
+ * on "rgmii-txid", "rgmii-rxid" or "rgmii" interfaces.
+ */
 static int vsc8601_add_skew(struct phy_device *phydev)
 {
 	int ret;