Merge branch 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata

Pull libata updates from Tejun Heo:
 "Nothing too interesting or alarming. Other than a new power saving
  mode addition to ahci and crash fix on a tracepoint, all changes are
  trivial or device-specific"

* 'for-4.15' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata: (22 commits)
  ahci: imx: Handle increased read failures for IMX53 temperature sensor in low frequency mode.
  ata: sata_dwc_460ex: Propagate platform device ID to DMA driver
  ata: fixes kernel crash while tracing ata_eh_link_autopsy event
  ata: pata_pdc2027x: Fix space before '[' error.
  libata: fix spelling mistake: 'ambigious' -> 'ambiguous'
  ata: ceva: Add SMMU support for SATA IP
  ata: ceva: Correct the suspend and resume logic for SATA
  ata: ceva: Correct the AXI bus configuration for SATA ports
  ata: ceva: Add CCI support for SATA if CCI is enabled
  ata: ceva: Make RxWaterMark value as module parameter
  ata: ceva: Disable Device Sleep capability
  ata: ceva: Add gen 3 mode support in driver
  ata: ceva: Move sata port phy oob settings to device-tree
  devicetree: bindings: Add sata port phy config parameters in ahci-ceva
  ata: mark expected switch fall-throughs
  ata: sata_mv: remove a redundant assignment to pointer ehi
  ahci: Add support for Cavium's fifth generation SATA controller
  ata: sata_rcar: Use of_device_get_match_data() helper
  libata: make ata_port_type const
  libata: make static arrays const, reduces object code size
  ...

Documentation/devicetree/bindings/ata/ahci-ceva.txt

@@ -5,6 +5,36 @@ Required properties:
   - compatible: Compatibility string. Must be 'ceva,ahci-1v84'.
   - clocks: Input clock specifier. Refer to common clock bindings.
   - interrupts: Interrupt specifier. Refer to interrupt binding.
+  - ceva,p0-cominit-params: OOB timing value for COMINIT parameter for port 0.
+  - ceva,p1-cominit-params: OOB timing value for COMINIT parameter for port 1.
+			The fields for the above parameter must be as shown below:
+			ceva,pN-cominit-params = /bits/ 8 <CIBGMN CIBGMX CIBGN CINMP>;
+			CINMP : COMINIT Negate Minimum Period.
+			CIBGN : COMINIT Burst Gap Nominal.
+			CIBGMX: COMINIT Burst Gap Maximum.
+			CIBGMN: COMINIT Burst Gap Minimum.
+  - ceva,p0-comwake-params: OOB timing value for COMWAKE parameter for port 0.
+  - ceva,p1-comwake-params: OOB timing value for COMWAKE parameter for port 1.
+			The fields for the above parameter must be as shown below:
+			ceva,pN-comwake-params = /bits/ 8 <CWBGMN CWBGMX CWBGN CWNMP>;
+			CWBGMN: COMWAKE Burst Gap Minimum.
+			CWBGMX: COMWAKE Burst Gap Maximum.
+			CWBGN: COMWAKE Burst Gap Nominal.
+			CWNMP: COMWAKE Negate Minimum Period.
+  - ceva,p0-burst-params: Burst timing value for COM parameter for port 0.
+  - ceva,p1-burst-params: Burst timing value for COM parameter for port 1.
+			The fields for the above parameter must be as shown below:
+			ceva,pN-burst-params = /bits/ 8 <BMX BNM SFD PTST>;
+			BMX: COM Burst Maximum.
+			BNM: COM Burst Nominal.
+			SFD: Signal Failure Detection value.
+			PTST: Partial to Slumber timer value.
+  - ceva,p0-retry-params: Retry interval timing value for port 0.
+  - ceva,p1-retry-params: Retry interval timing value for port 1.
+			The fields for the above parameter must be as shown below:
+			ceva,pN-retry-params = /bits/ 16 <RIT RCT>;
+			RIT:  Retry Interval Timer.
+			RCT:  Rate Change Timer.
 
 Optional properties:
   - ceva,broken-gen2: limit to gen1 speed instead of gen2.
@@ -16,5 +46,14 @@ Examples:
 		interrupt-parent = <&gic>;
 		interrupts = <0 133 4>;
 		clocks = <&clkc SATA_CLK_ID>;
+		ceva,p0-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+		ceva,p0-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+		ceva,p0-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+		ceva,p0-retry-params = /bits/ 16 <0x0216 0x7F06>;
+
+		ceva,p1-cominit-params = /bits/ 8 <0x0F 0x25 0x18 0x29>;
+		ceva,p1-comwake-params = /bits/ 8 <0x04 0x0B 0x08 0x0F>;
+		ceva,p1-burst-params = /bits/ 8 <0x0A 0x08 0x4A 0x06>;
+		ceva,p1-retry-params = /bits/ 16 <0x0216 0x7F06>;
 		ceva,broken-gen2;
 	};

drivers/ata/ahci.c

@@ -57,6 +57,7 @@ enum {
 	AHCI_PCI_BAR_STA2X11	= 0,
 	AHCI_PCI_BAR_CAVIUM	= 0,
 	AHCI_PCI_BAR_ENMOTUS	= 2,
+	AHCI_PCI_BAR_CAVIUM_GEN5	= 4,
 	AHCI_PCI_BAR_STANDARD	= 5,
 };
 
@@ -1570,8 +1571,12 @@ static int ahci_init_one(struct pci_dev *pdev, const struct pci_device_id *ent)
 		ahci_pci_bar = AHCI_PCI_BAR_STA2X11;
 	else if (pdev->vendor == 0x1c44 && pdev->device == 0x8000)
 		ahci_pci_bar = AHCI_PCI_BAR_ENMOTUS;
-	else if (pdev->vendor == 0x177d && pdev->device == 0xa01c)
-		ahci_pci_bar = AHCI_PCI_BAR_CAVIUM;
+	else if (pdev->vendor == PCI_VENDOR_ID_CAVIUM) {
+		if (pdev->device == 0xa01c)
+			ahci_pci_bar = AHCI_PCI_BAR_CAVIUM;
+		if (pdev->device == 0xa084)
+			ahci_pci_bar = AHCI_PCI_BAR_CAVIUM_GEN5;
+	}
 
 	/* acquire resources */
 	rc = pcim_enable_device(pdev);

drivers/ata/ahci_ceva.c

@@ -32,15 +32,27 @@
 #define AHCI_VEND_PP3C  0xB0
 #define AHCI_VEND_PP4C  0xB4
 #define AHCI_VEND_PP5C  0xB8
+#define AHCI_VEND_AXICC 0xBC
 #define AHCI_VEND_PAXIC 0xC0
 #define AHCI_VEND_PTC   0xC8
 
 /* Vendor Specific Register bit definitions */
 #define PAXIC_ADBW_BW64 0x1
-#define PAXIC_MAWIDD	(1 << 8)
-#define PAXIC_MARIDD	(1 << 16)
+#define PAXIC_MAWID(i)	(((i) * 2) << 4)
+#define PAXIC_MARID(i)	(((i) * 2) << 12)
+#define PAXIC_MARIDD(i)	((((i) * 2) + 1) << 16)
+#define PAXIC_MAWIDD(i)	((((i) * 2) + 1) << 8)
 #define PAXIC_OTL	(0x4 << 20)
 
+/* Register bit definitions for cache control */
+#define AXICC_ARCA_VAL  (0xF << 0)
+#define AXICC_ARCF_VAL  (0xF << 4)
+#define AXICC_ARCH_VAL  (0xF << 8)
+#define AXICC_ARCP_VAL  (0xF << 12)
+#define AXICC_AWCFD_VAL (0xF << 16)
+#define AXICC_AWCD_VAL  (0xF << 20)
+#define AXICC_AWCF_VAL  (0xF << 24)
+
 #define PCFG_TPSS_VAL	(0x32 << 16)
 #define PCFG_TPRS_VAL	(0x2 << 12)
 #define PCFG_PAD_VAL	0x2
@@ -50,21 +62,6 @@
 #define PPCFG_PSS_EN	(1 << 29)
 #define PPCFG_ESDF_EN	(1 << 31)
 
-#define PP2C_CIBGMN	0x0F
-#define PP2C_CIBGMX	(0x25 << 8)
-#define PP2C_CIBGN	(0x18 << 16)
-#define PP2C_CINMP	(0x29 << 24)
-
-#define PP3C_CWBGMN	0x04
-#define PP3C_CWBGMX	(0x0B << 8)
-#define PP3C_CWBGN	(0x08 << 16)
-#define PP3C_CWNMP	(0x0F << 24)
-
-#define PP4C_BMX	0x0a
-#define PP4C_BNM	(0x08 << 8)
-#define PP4C_SFD	(0x4a << 16)
-#define PP4C_PTST	(0x06 << 24)
-
 #define PP5C_RIT	0x60216
 #define PP5C_RCT	(0x7f0 << 20)
 
@@ -75,6 +72,7 @@
 #define PORT1_BASE	0x180
 
 /* Port Control Register Bit Definitions */
+#define PORT_SCTL_SPD_GEN3	(0x3 << 4)
 #define PORT_SCTL_SPD_GEN2	(0x2 << 4)
 #define PORT_SCTL_SPD_GEN1	(0x1 << 4)
 #define PORT_SCTL_IPM		(0x3 << 8)
@@ -85,13 +83,43 @@
 #define DRV_NAME	"ahci-ceva"
 #define CEVA_FLAG_BROKEN_GEN2	1
 
+static unsigned int rx_watermark = PTC_RX_WM_VAL;
+module_param(rx_watermark, uint, 0644);
+MODULE_PARM_DESC(rx_watermark, "RxWaterMark value (0 - 0x80)");
+
 struct ceva_ahci_priv {
 	struct platform_device *ahci_pdev;
+	/* Port Phy2Cfg Register */
+	u32 pp2c[NR_PORTS];
+	u32 pp3c[NR_PORTS];
+	u32 pp4c[NR_PORTS];
+	u32 pp5c[NR_PORTS];
+	/* Axi Cache Control Register */
+	u32 axicc;
+	bool is_cci_enabled;
 	int flags;
 };
 
+static unsigned int ceva_ahci_read_id(struct ata_device *dev,
+					struct ata_taskfile *tf, u16 *id)
+{
+	u32 err_mask;
+
+	err_mask = ata_do_dev_read_id(dev, tf, id);
+	if (err_mask)
+		return err_mask;
+	/*
+	 * Since CEVA controller does not support device sleep feature, we
+	 * need to clear DEVSLP (bit 8) in word78 of the IDENTIFY DEVICE data.
+	 */
+	id[ATA_ID_FEATURE_SUPP] &= cpu_to_le16(~(1 << 8));
+
+	return 0;
+}
+
 static struct ata_port_operations ahci_ceva_ops = {
 	.inherits = &ahci_platform_ops,
+	.read_id = ceva_ahci_read_id,
 };
 
 static const struct ata_port_info ahci_ceva_port_info = {
@@ -108,14 +136,6 @@ static void ahci_ceva_setup(struct ahci_host_priv *hpriv)
 	u32 tmp;
 	int i;
 
-	/*
-	 * AXI Data bus width to 64
-	 * Set Mem Addr Read, Write ID for data transfers
-	 * Transfer limit to 72 DWord
-	 */
-	tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD | PAXIC_MARIDD | PAXIC_OTL;
-	writel(tmp, mmio + AHCI_VEND_PAXIC);
-
 	/* Set AHCI Enable */
 	tmp = readl(mmio + HOST_CTL);
 	tmp |= HOST_AHCI_EN;
@@ -126,32 +146,48 @@ static void ahci_ceva_setup(struct ahci_host_priv *hpriv)
 		tmp = PCFG_TPSS_VAL | PCFG_TPRS_VAL | (PCFG_PAD_VAL + i);
 		writel(tmp, mmio + AHCI_VEND_PCFG);
 
+		/*
+		 * AXI Data bus width to 64
+		 * Set Mem Addr Read, Write ID for data transfers
+		 * Set Mem Addr Read ID, Write ID for non-data transfers
+		 * Transfer limit to 72 DWord
+		 */
+		tmp = PAXIC_ADBW_BW64 | PAXIC_MAWIDD(i) | PAXIC_MARIDD(i) |
+			PAXIC_MAWID(i) | PAXIC_MARID(i) | PAXIC_OTL;
+		writel(tmp, mmio + AHCI_VEND_PAXIC);
+
+		/* Set AXI cache control register if CCi is enabled */
+		if (cevapriv->is_cci_enabled) {
+			tmp = readl(mmio + AHCI_VEND_AXICC);
+			tmp |= AXICC_ARCA_VAL | AXICC_ARCF_VAL |
+				AXICC_ARCH_VAL | AXICC_ARCP_VAL |
+				AXICC_AWCFD_VAL | AXICC_AWCD_VAL |
+				AXICC_AWCF_VAL;
+			writel(tmp, mmio + AHCI_VEND_AXICC);
+		}
+
 		/* Port Phy Cfg register enables */
 		tmp = PPCFG_TTA | PPCFG_PSS_EN | PPCFG_ESDF_EN;
 		writel(tmp, mmio + AHCI_VEND_PPCFG);
 
 		/* Phy Control OOB timing parameters COMINIT */
-		tmp = PP2C_CIBGMN | PP2C_CIBGMX | PP2C_CIBGN | PP2C_CINMP;
-		writel(tmp, mmio + AHCI_VEND_PP2C);
+		writel(cevapriv->pp2c[i], mmio + AHCI_VEND_PP2C);
 
 		/* Phy Control OOB timing parameters COMWAKE */
-		tmp = PP3C_CWBGMN | PP3C_CWBGMX | PP3C_CWBGN | PP3C_CWNMP;
-		writel(tmp, mmio + AHCI_VEND_PP3C);
+		writel(cevapriv->pp3c[i], mmio + AHCI_VEND_PP3C);
 
 		/* Phy Control Burst timing setting */
-		tmp = PP4C_BMX | PP4C_BNM | PP4C_SFD | PP4C_PTST;
-		writel(tmp, mmio + AHCI_VEND_PP4C);
+		writel(cevapriv->pp4c[i], mmio + AHCI_VEND_PP4C);
 
 		/* Rate Change Timer and Retry Interval Timer setting */
-		tmp = PP5C_RIT | PP5C_RCT;
-		writel(tmp, mmio + AHCI_VEND_PP5C);
+		writel(cevapriv->pp5c[i], mmio + AHCI_VEND_PP5C);
 
 		/* Rx Watermark setting  */
-		tmp = PTC_RX_WM_VAL | PTC_RSVD;
+		tmp = rx_watermark | PTC_RSVD;
 		writel(tmp, mmio + AHCI_VEND_PTC);
 
-		/* Default to Gen 2 Speed and Gen 1 if Gen2 is broken */
-		tmp = PORT_SCTL_SPD_GEN2 | PORT_SCTL_IPM;
+		/* Default to Gen 3 Speed and Gen 1 if Gen2 is broken */
+		tmp = PORT_SCTL_SPD_GEN3 | PORT_SCTL_IPM;
 		if (cevapriv->flags & CEVA_FLAG_BROKEN_GEN2)
 			tmp = PORT_SCTL_SPD_GEN1 | PORT_SCTL_IPM;
 		writel(tmp, mmio + PORT_SCR_CTL + PORT_BASE + PORT_OFFSET * i);
@@ -168,6 +204,7 @@ static int ceva_ahci_probe(struct platform_device *pdev)
 	struct device *dev = &pdev->dev;
 	struct ahci_host_priv *hpriv;
 	struct ceva_ahci_priv *cevapriv;
+	enum dev_dma_attr attr;
 	int rc;
 
 	cevapriv = devm_kzalloc(dev, sizeof(*cevapriv), GFP_KERNEL);
@@ -187,6 +224,65 @@ static int ceva_ahci_probe(struct platform_device *pdev)
 	if (of_property_read_bool(np, "ceva,broken-gen2"))
 		cevapriv->flags = CEVA_FLAG_BROKEN_GEN2;
 
+	/* Read OOB timing value for COMINIT from device-tree */
+	if (of_property_read_u8_array(np, "ceva,p0-cominit-params",
+					(u8 *)&cevapriv->pp2c[0], 4) < 0) {
+		dev_warn(dev, "ceva,p0-cominit-params property not defined\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_u8_array(np, "ceva,p1-cominit-params",
+					(u8 *)&cevapriv->pp2c[1], 4) < 0) {
+		dev_warn(dev, "ceva,p1-cominit-params property not defined\n");
+		return -EINVAL;
+	}
+
+	/* Read OOB timing value for COMWAKE from device-tree*/
+	if (of_property_read_u8_array(np, "ceva,p0-comwake-params",
+					(u8 *)&cevapriv->pp3c[0], 4) < 0) {
+		dev_warn(dev, "ceva,p0-comwake-params property not defined\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_u8_array(np, "ceva,p1-comwake-params",
+					(u8 *)&cevapriv->pp3c[1], 4) < 0) {
+		dev_warn(dev, "ceva,p1-comwake-params property not defined\n");
+		return -EINVAL;
+	}
+
+	/* Read phy BURST timing value from device-tree */
+	if (of_property_read_u8_array(np, "ceva,p0-burst-params",
+					(u8 *)&cevapriv->pp4c[0], 4) < 0) {
+		dev_warn(dev, "ceva,p0-burst-params property not defined\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_u8_array(np, "ceva,p1-burst-params",
+					(u8 *)&cevapriv->pp4c[1], 4) < 0) {
+		dev_warn(dev, "ceva,p1-burst-params property not defined\n");
+		return -EINVAL;
+	}
+
+	/* Read phy RETRY interval timing value from device-tree */
+	if (of_property_read_u16_array(np, "ceva,p0-retry-params",
+					(u16 *)&cevapriv->pp5c[0], 2) < 0) {
+		dev_warn(dev, "ceva,p0-retry-params property not defined\n");
+		return -EINVAL;
+	}
+
+	if (of_property_read_u16_array(np, "ceva,p1-retry-params",
+					(u16 *)&cevapriv->pp5c[1], 2) < 0) {
+		dev_warn(dev, "ceva,p1-retry-params property not defined\n");
+		return -EINVAL;
+	}
+
+	/*
+	 * Check if CCI is enabled for SATA. The DEV_DMA_COHERENT is returned
+	 * if CCI is enabled, so check for DEV_DMA_COHERENT.
+	 */
+	attr = device_get_dma_attr(dev);
+	cevapriv->is_cci_enabled = (attr == DEV_DMA_COHERENT);
+
 	hpriv->plat_data = cevapriv;
 
 	/* CEVA specific initialization */
@@ -206,12 +302,37 @@ static int ceva_ahci_probe(struct platform_device *pdev)
 
 static int __maybe_unused ceva_ahci_suspend(struct device *dev)
 {
-	return ahci_platform_suspend_host(dev);
+	return ahci_platform_suspend(dev);
 }
 
 static int __maybe_unused ceva_ahci_resume(struct device *dev)
 {
-	return ahci_platform_resume_host(dev);
+	struct ata_host *host = dev_get_drvdata(dev);
+	struct ahci_host_priv *hpriv = host->private_data;
+	int rc;
+
+	rc = ahci_platform_enable_resources(hpriv);
+	if (rc)
+		return rc;
+
+	/* Configure CEVA specific config before resuming HBA */
+	ahci_ceva_setup(hpriv);
+
+	rc = ahci_platform_resume_host(dev);
+	if (rc)
+		goto disable_resources;
+
+	/* We resumed so update PM runtime state */
+	pm_runtime_disable(dev);
+	pm_runtime_set_active(dev);
+	pm_runtime_enable(dev);
+
+	return 0;
+
+disable_resources:
+	ahci_platform_disable_resources(hpriv);
+
+	return rc;
 }
 
 static SIMPLE_DEV_PM_OPS(ahci_ceva_pm_ops, ceva_ahci_suspend, ceva_ahci_resume);

drivers/ata/ahci_imx.c

@@ -230,7 +230,7 @@ static int read_adc_sum(void *dev, u16 rtune_ctl_reg, void __iomem * mmio)
 {
 	u16 adc_out_reg, read_sum;
 	u32 index, read_attempt;
-	const u32 attempt_limit = 100;
+	const u32 attempt_limit = 200;
 
 	imx_phy_reg_addressing(SATA_PHY_CR_CLOCK_RTUNE_CTL, mmio);
 	imx_phy_reg_write(rtune_ctl_reg, mmio);

drivers/ata/libahci_platform.c

@@ -295,6 +295,7 @@ static int ahci_platform_get_phy(struct ahci_host_priv *hpriv, u32 port,
 				node->name);
 			break;
 		}
+		/* fall through */
 	case -ENODEV:
 		/* continue normally */
 		hpriv->phys[port] = NULL;

drivers/ata/libata-core.c

@@ -1879,6 +1879,7 @@ int ata_dev_read_id(struct ata_device *dev, unsigned int *p_class,
 	switch (class) {
 	case ATA_DEV_SEMB:
 		class = ATA_DEV_ATA;	/* some hard drives report SEMB sig */
+		/* fall through */
 	case ATA_DEV_ATA:
 	case ATA_DEV_ZAC:
 		tf.command = ATA_CMD_ID_ATA;
@@ -2975,6 +2976,7 @@ int ata_bus_probe(struct ata_port *ap)
 	case -ENODEV:
 		/* give it just one more chance */
 		tries[dev->devno] = min(tries[dev->devno], 1);
+		/* fall through */
 	case -EIO:
 		if (tries[dev->devno] == 1) {
 			/* This is the last chance, better to slow
@@ -3462,6 +3464,7 @@ int ata_down_xfermask_limit(struct ata_device *dev, unsigned int sel)
 
 	case ATA_DNXFER_FORCE_PIO0:
 		pio_mask &= 1;
+		/* fall through */
 	case ATA_DNXFER_FORCE_PIO:
 		mwdma_mask = 0;
 		udma_mask = 0;
@@ -3964,6 +3967,7 @@ int sata_link_scr_lpm(struct ata_link *link, enum ata_lpm_policy policy,
 		scontrol &= ~(0x1 << 8);
 		scontrol |= (0x6 << 8);
 		break;
+	case ATA_LPM_MED_POWER_WITH_DIPM:
 	case ATA_LPM_MIN_POWER:
 		if (ata_link_nr_enabled(link) > 0)
 			/* no restrictions on LPM transitions */
@@ -5823,7 +5827,7 @@ void ata_host_resume(struct ata_host *host)
 }
 #endif
 
-struct device_type ata_port_type = {
+const struct device_type ata_port_type = {
 	.name = "ata_port",
 #ifdef CONFIG_PM
 	.pm = &ata_port_pm_ops,
@@ -6903,7 +6907,7 @@ static int __init ata_parse_force_one(char **cur,
 		return -EINVAL;
 	}
 	if (nr_matches > 1) {
-		*reason = "ambigious value";
+		*reason = "ambiguous value";
 		return -EINVAL;
 	}
 

drivers/ata/libata-eh.c

@@ -2264,8 +2264,8 @@ static void ata_eh_link_autopsy(struct ata_link *link)
 		if (dev->flags & ATA_DFLAG_DUBIOUS_XFER)
 			eflags |= ATA_EFLAG_DUBIOUS_XFER;
 		ehc->i.action |= ata_eh_speed_down(dev, eflags, all_err_mask);
+		trace_ata_eh_link_autopsy(dev, ehc->i.action, all_err_mask);
 	}
-	trace_ata_eh_link_autopsy(dev, ehc->i.action, all_err_mask);
 	DPRINTK("EXIT\n");
 }
 
@@ -3454,9 +3454,9 @@ static int ata_eh_maybe_retry_flush(struct ata_device *dev)
  *	@r_failed_dev: out parameter for failed device
  *
  *	Enable SATA Interface power management.  This will enable
- *	Device Interface Power Management (DIPM) for min_power
- * 	policy, and then call driver specific callbacks for
- *	enabling Host Initiated Power management.
+ *	Device Interface Power Management (DIPM) for min_power and
+ *	medium_power_with_dipm policies, and then call driver specific
+ *	callbacks for enabling Host Initiated Power management.
  *
  *	LOCKING:
  *	EH context.
@@ -3502,7 +3502,7 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
 			hints &= ~ATA_LPM_HIPM;
 
 		/* disable DIPM before changing link config */
-		if (policy != ATA_LPM_MIN_POWER && dipm) {
+		if (policy < ATA_LPM_MED_POWER_WITH_DIPM && dipm) {
 			err_mask = ata_dev_set_feature(dev,
 					SETFEATURES_SATA_DISABLE, SATA_DIPM);
 			if (err_mask && err_mask != AC_ERR_DEV) {
@@ -3545,7 +3545,7 @@ static int ata_eh_set_lpm(struct ata_link *link, enum ata_lpm_policy policy,
 
 	/* host config updated, enable DIPM if transitioning to MIN_POWER */
 	ata_for_each_dev(dev, link, ENABLED) {
-		if (policy == ATA_LPM_MIN_POWER && !no_dipm &&
+		if (policy >= ATA_LPM_MED_POWER_WITH_DIPM && !no_dipm &&
 		    ata_id_has_dipm(dev->id)) {
 			err_mask = ata_dev_set_feature(dev,
 					SETFEATURES_SATA_ENABLE, SATA_DIPM);
@@ -3711,9 +3711,11 @@ static int ata_eh_handle_dev_fail(struct ata_device *dev, int err)
 	case -ENODEV:
 		/* device missing or wrong IDENTIFY data, schedule probing */
 		ehc->i.probe_mask |= (1 << dev->devno);
+		/* fall through */
 	case -EINVAL:
 		/* give it just one more chance */
 		ehc->tries[dev->devno] = min(ehc->tries[dev->devno], 1);
+		/* fall through */
 	case -EIO:
 		if (ehc->tries[dev->devno] == 1) {
 			/* This is the last chance, better to slow

drivers/ata/libata-scsi.c

@@ -106,10 +106,11 @@ static const u8 def_control_mpage[CONTROL_MPAGE_LEN] = {
 };
 
 static const char *ata_lpm_policy_names[] = {
-	[ATA_LPM_UNKNOWN]	= "max_performance",
-	[ATA_LPM_MAX_POWER]	= "max_performance",
-	[ATA_LPM_MED_POWER]	= "medium_power",
-	[ATA_LPM_MIN_POWER]	= "min_power",
+	[ATA_LPM_UNKNOWN]		= "max_performance",
+	[ATA_LPM_MAX_POWER]		= "max_performance",
+	[ATA_LPM_MED_POWER]		= "medium_power",
+	[ATA_LPM_MED_POWER_WITH_DIPM]	= "med_power_with_dipm",
+	[ATA_LPM_MIN_POWER]		= "min_power",
 };
 
 static ssize_t ata_scsi_lpm_store(struct device *device,
@@ -2145,7 +2146,7 @@ static void ata_scsi_rbuf_fill(struct ata_scsi_args *args,
  */
 static unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf)
 {
-	const u8 versions[] = {
+	static const u8 versions[] = {
 		0x00,
 		0x60,	/* SAM-3 (no version claimed) */
 
@@ -2155,7 +2156,7 @@ static unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf)
 		0x03,
 		0x00	/* SPC-3 (no version claimed) */
 	};
-	const u8 versions_zbc[] = {
+	static const u8 versions_zbc[] = {
 		0x00,
 		0xA0,	/* SAM-5 (no version claimed) */
 
@@ -2227,7 +2228,7 @@ static unsigned int ata_scsiop_inq_std(struct ata_scsi_args *args, u8 *rbuf)
 static unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf)
 {
 	int num_pages;
-	const u8 pages[] = {
+	static const u8 pages[] = {
 		0x00,	/* page 0x00, this page */
 		0x80,	/* page 0x80, unit serial no page */
 		0x83,	/* page 0x83, device ident page */
@@ -2258,7 +2259,7 @@ static unsigned int ata_scsiop_inq_00(struct ata_scsi_args *args, u8 *rbuf)
  */
 static unsigned int ata_scsiop_inq_80(struct ata_scsi_args *args, u8 *rbuf)
 {
-	const u8 hdr[] = {
+	static const u8 hdr[] = {
 		0,
 		0x80,			/* this page code */
 		0,
@@ -2580,7 +2581,7 @@ static unsigned int ata_scsiop_mode_sense(struct ata_scsi_args *args, u8 *rbuf)
 {
 	struct ata_device *dev = args->dev;
 	u8 *scsicmd = args->cmd->cmnd, *p = rbuf;
-	const u8 sat_blk_desc[] = {
+	static const u8 sat_blk_desc[] = {
 		0, 0, 0, 0,	/* number of blocks: sat unspecified */
 		0,
 		0, 0x2, 0x0	/* block length: 512 bytes */

drivers/ata/libata.h

@@ -51,7 +51,7 @@ extern int atapi_passthru16;
 extern int libata_fua;
 extern int libata_noacpi;
 extern int libata_allow_tpm;
-extern struct device_type ata_port_type;
+extern const struct device_type ata_port_type;
 extern struct ata_link *ata_dev_phys_link(struct ata_device *dev);
 extern void ata_force_cbl(struct ata_port *ap);
 extern u64 ata_tf_to_lba(const struct ata_taskfile *tf);

drivers/ata/pata_artop.c

@@ -242,7 +242,7 @@ static void artop6210_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 
 static void artop6260_set_dmamode (struct ata_port *ap, struct ata_device *adev)
 {
-	unsigned int pio	= adev->pio_mode - XFER_PIO_0;
+	unsigned int pio;
 	struct pci_dev *pdev	= to_pci_dev(ap->host->dev);
 	u8 ultra;
 

drivers/ata/pata_atp867x.c

@@ -171,6 +171,7 @@ static int atp867x_get_active_clocks_shifted(struct ata_port *ap,
 	default:
 		printk(KERN_WARNING "ATP867X: active %dclk is invalid. "
 			"Using 12clk.\n", clk);
+		/* fall through */
 	case 9 ... 12:
 		clocks = 7;	/* 12 clk */
 		break;
@@ -203,6 +204,7 @@ static int atp867x_get_recover_clocks_shifted(unsigned int clk)
 	default:
 		printk(KERN_WARNING "ATP867X: recover %dclk is invalid. "
 			"Using default 12clk.\n", clk);
+		/* fall through */
 	case 12:	/* default 12 clk */
 		clocks = 0;
 		break;

drivers/ata/pata_pdc2027x.c

@@ -84,7 +84,7 @@ static int pdc2027x_set_mode(struct ata_link *link, struct ata_device **r_failed
  */
 static struct pdc2027x_pio_timing {
 	u8 value0, value1, value2;
-} pdc2027x_pio_timing_tbl [] = {
+} pdc2027x_pio_timing_tbl[] = {
 	{ 0xfb, 0x2b, 0xac }, /* PIO mode 0 */
 	{ 0x46, 0x29, 0xa4 }, /* PIO mode 1 */
 	{ 0x23, 0x26, 0x64 }, /* PIO mode 2 */
@@ -94,7 +94,7 @@ static struct pdc2027x_pio_timing {
 
 static struct pdc2027x_mdma_timing {
 	u8 value0, value1;
-} pdc2027x_mdma_timing_tbl [] = {
+} pdc2027x_mdma_timing_tbl[] = {
 	{ 0xdf, 0x5f }, /* MDMA mode 0 */
 	{ 0x6b, 0x27 }, /* MDMA mode 1 */
 	{ 0x69, 0x25 }, /* MDMA mode 2 */
@@ -102,7 +102,7 @@ static struct pdc2027x_mdma_timing {
 
 static struct pdc2027x_udma_timing {
 	u8 value0, value1, value2;
-} pdc2027x_udma_timing_tbl [] = {
+} pdc2027x_udma_timing_tbl[] = {
 	{ 0x4a, 0x0f, 0xd5 }, /* UDMA mode 0 */
 	{ 0x3a, 0x0a, 0xd0 }, /* UDMA mode 1 */
 	{ 0x2a, 0x07, 0xcd }, /* UDMA mode 2 */

drivers/ata/sata_dwc_460ex.c

@@ -248,6 +248,7 @@ static int sata_dwc_dma_init_old(struct platform_device *pdev,
 		return -ENOMEM;
 
 	hsdev->dma->dev = &pdev->dev;
+	hsdev->dma->id = pdev->id;
 
 	/* Get SATA DMA interrupt number */
 	hsdev->dma->irq = irq_of_parse_and_map(np, 1);

drivers/ata/sata_mv.c

@@ -2387,7 +2387,7 @@ static unsigned int mv_qc_issue(struct ata_queued_cmd *qc)
 				      ": attempting PIO w/multiple DRQ: "
 				      "this may fail due to h/w errata\n");
 		}
-		/* drop through */
+		/* fall through */
 	case ATA_PROT_NODATA:
 	case ATAPI_PROT_PIO:
 	case ATAPI_PROT_NODATA:
@@ -2478,20 +2478,18 @@ static unsigned int mv_get_err_pmp_map(struct ata_port *ap)
 
 static void mv_pmp_eh_prep(struct ata_port *ap, unsigned int pmp_map)
 {
-	struct ata_eh_info *ehi;
 	unsigned int pmp;
 
 	/*
 	 * Initialize EH info for PMPs which saw device errors
 	 */
-	ehi = &ap->link.eh_info;
 	for (pmp = 0; pmp_map != 0; pmp++) {
 		unsigned int this_pmp = (1 << pmp);
 		if (pmp_map & this_pmp) {
 			struct ata_link *link = &ap->pmp_link[pmp];
+			struct ata_eh_info *ehi = &link->eh_info;
 
 			pmp_map &= ~this_pmp;
-			ehi = &link->eh_info;
 			ata_ehi_clear_desc(ehi);
 			ata_ehi_push_desc(ehi, "dev err");
 			ehi->err_mask |= AC_ERR_DEV;
@@ -3877,7 +3875,7 @@ static int mv_chip_id(struct ata_host *host, unsigned int board_idx)
 				" and avoid the final two gigabytes on"
 				" all RocketRAID BIOS initialized drives.\n");
 		}
-		/* drop through */
+		/* fall through */
 	case chip_6042:
 		hpriv->ops = &mv6xxx_ops;
 		hp_flags |= MV_HP_GEN_IIE;

drivers/ata/sata_rcar.c

@@ -872,7 +872,6 @@ MODULE_DEVICE_TABLE(of, sata_rcar_match);
 
 static int sata_rcar_probe(struct platform_device *pdev)
 {
-	const struct of_device_id *of_id;
 	struct ata_host *host;
 	struct sata_rcar_priv *priv;
 	struct resource *mem;
@@ -888,11 +887,7 @@ static int sata_rcar_probe(struct platform_device *pdev)
 	if (!priv)
 		return -ENOMEM;
 
-	of_id = of_match_device(sata_rcar_match, &pdev->dev);
-	if (!of_id)
-		return -ENODEV;
-
-	priv->type = (enum sata_rcar_type)of_id->data;
+	priv->type = (enum sata_rcar_type)of_device_get_match_data(&pdev->dev);
 	priv->clk = devm_clk_get(&pdev->dev, NULL);
 	if (IS_ERR(priv->clk)) {
 		dev_err(&pdev->dev, "failed to get access to sata clock\n");

include/linux/libata.h

@@ -522,6 +522,7 @@ enum ata_lpm_policy {
 	ATA_LPM_UNKNOWN,
 	ATA_LPM_MAX_POWER,
 	ATA_LPM_MED_POWER,
+	ATA_LPM_MED_POWER_WITH_DIPM, /* Med power + DIPM as win IRST does */
 	ATA_LPM_MIN_POWER,
 };