Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input

Pull input updates from Dmitry Torokhov:
 - new driver for eGalaxTouch serial touchscreen
 - new driver for TS-4800 touchscreen
 - an update for Goodix touchscreen driver
 - PS/2 mouse module was reworked to limit number of protocols we try on
   pass-through ports to speed up their detection time
 - wacom_w8001 touchscreen driver now reports pen and touch via separate
   instances of input devices
 - other driver changes

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (42 commits)
  Input: elantech - mark protocols v2 and v3 as semi-mt
  Input: wacom_w8001 - drop use of ABS_MT_TOOL_TYPE
  Input: gpio-keys - fix check for disabling unsupported keys
  Input: omap-keypad - remove dead check
  Input: ti_am335x_tsc - fix HWPEN interrupt handling
  Input: omap-keypad - set tasklet data earlier
  Input: rohm_bu21023 - fix handling of retrying firmware update
  Input: ALPS - report v3 pinnacle trackstick device only if is present
  Input: ALPS - detect trackstick presence for v7 protocol
  Input: pcap_ts - use to_delayed_work
  Input: bma150 - constify bma150_cfg structure
  Input: i8042 - add Fujitsu Lifebook U745 to the nomux list
  Input: egalax_ts_serial - fix potential NULL dereference on error
  Input: uinput - sanity check on ff_effects_max and EV_FF
  Input: uinput - rework ABS validation
  Input: uinput - add new UINPUT_DEV_SETUP and UI_ABS_SETUP ioctl
  Input: goodix - use "inverted_[xy]" flags instead of "rotated_screen"
  Input: goodix - add axis swapping and axis inversion support
  Input: goodix - use goodix_i2c_write_u8 instead of i2c_master_send
  Input: goodix - add power management support
  ...

Documentation/devicetree/bindings/input/touchscreen/goodix.txt

@@ -13,6 +13,17 @@ Required properties:
  - interrupt-parent	: Interrupt controller to which the chip is connected
  - interrupts		: Interrupt to which the chip is connected
 
+Optional properties:
+
+ - irq-gpios		: GPIO pin used for IRQ. The driver uses the
+			  interrupt gpio pin as output to reset the device.
+ - reset-gpios		: GPIO pin used for reset
+
+ - touchscreen-inverted-x  : X axis is inverted (boolean)
+ - touchscreen-inverted-y  : Y axis is inverted (boolean)
+ - touchscreen-swapped-x-y : X and Y axis are swapped (boolean)
+                             (swapping is done after inverting the axis)
+
 Example:
 
 	i2c@00000000 {
@@ -23,6 +34,9 @@ Example:
 			reg = <0x5d>;
 			interrupt-parent = <&gpio>;
 			interrupts = <0 0>;
+
+			irq-gpios = <&gpio1 0 0>;
+			reset-gpios = <&gpio1 1 0>;
 		};
 
 		/* ... */

Documentation/devicetree/bindings/input/touchscreen/pixcir_i2c_ts.txt

@@ -9,7 +9,9 @@ Required properties:
 - touchscreen-size-y: vertical resolution of touchscreen (in pixels)
 
 Optional properties:
-- reset-gpio: GPIO connected to the RESET line of the chip
+- reset-gpios: GPIO connected to the RESET line of the chip
+- enable-gpios: GPIO connected to the ENABLE line of the chip
+- wake-gpios: GPIO connected to the WAKE line of the chip
 
 Example:
 

Documentation/devicetree/bindings/input/touchscreen/ts4800-ts.txt

+* TS-4800 Touchscreen bindings
+
+Required properties:
+- compatible: must be "technologic,ts4800-ts"
+- reg: physical base address of the controller and length of memory mapped
+  region.
+- syscon: phandle / integers array that points to the syscon node which
+          describes the FPGA's syscon registers.
+          - phandle to FPGA's syscon
+          - offset to the touchscreen register
+          - offset to the touchscreen enable bit

drivers/gpio/gpiolib-acpi.c

@@ -943,3 +943,46 @@ int acpi_gpio_count(struct device *dev, const char *con_id)
 	}
 	return count;
 }
+
+struct acpi_crs_lookup {
+	struct list_head node;
+	struct acpi_device *adev;
+	const char *con_id;
+};
+
+static DEFINE_MUTEX(acpi_crs_lookup_lock);
+static LIST_HEAD(acpi_crs_lookup_list);
+
+bool acpi_can_fallback_to_crs(struct acpi_device *adev, const char *con_id)
+{
+	struct acpi_crs_lookup *l, *lookup = NULL;
+
+	/* Never allow fallback if the device has properties */
+	if (adev->data.properties || adev->driver_gpios)
+		return false;
+
+	mutex_lock(&acpi_crs_lookup_lock);
+
+	list_for_each_entry(l, &acpi_crs_lookup_list, node) {
+		if (l->adev == adev) {
+			lookup = l;
+			break;
+		}
+	}
+
+	if (!lookup) {
+		lookup = kmalloc(sizeof(*lookup), GFP_KERNEL);
+		if (lookup) {
+			lookup->adev = adev;
+			lookup->con_id = con_id;
+			list_add_tail(&lookup->node, &acpi_crs_lookup_list);
+		}
+	}
+
+	mutex_unlock(&acpi_crs_lookup_lock);
+
+	return lookup &&
+		((!lookup->con_id && !con_id) ||
+		 (lookup->con_id && con_id &&
+		  strcmp(lookup->con_id, con_id) == 0));
+}

drivers/gpio/gpiolib.c

@@ -1874,6 +1874,9 @@ static struct gpio_desc *acpi_find_gpio(struct device *dev, const char *con_id,
 
 	/* Then from plain _CRS GPIOs */
 	if (IS_ERR(desc)) {
+		if (!acpi_can_fallback_to_crs(adev, con_id))
+			return ERR_PTR(-ENOENT);
+
 		desc = acpi_get_gpiod_by_index(adev, NULL, idx, &info);
 		if (IS_ERR(desc))
 			return desc;

drivers/gpio/gpiolib.h

@@ -48,6 +48,8 @@ struct gpio_desc *acpi_node_get_gpiod(struct fwnode_handle *fwnode,
 				      struct acpi_gpio_info *info);
 
 int acpi_gpio_count(struct device *dev, const char *con_id);
+
+bool acpi_can_fallback_to_crs(struct acpi_device *adev, const char *con_id);
 #else
 static inline void acpi_gpiochip_add(struct gpio_chip *chip) { }
 static inline void acpi_gpiochip_remove(struct gpio_chip *chip) { }
@@ -74,6 +76,12 @@ static inline int acpi_gpio_count(struct device *dev, const char *con_id)
 {
 	return -ENODEV;
 }
+
+static inline bool acpi_can_fallback_to_crs(struct acpi_device *adev,
+					    const char *con_id)
+{
+	return false;
+}
 #endif
 
 struct gpio_desc *of_get_named_gpiod_flags(struct device_node *np,

drivers/input/keyboard/gpio_keys.c

@@ -96,13 +96,29 @@ struct gpio_keys_drvdata {
  * Return value of this function can be used to allocate bitmap
  * large enough to hold all bits for given type.
  */
-static inline int get_n_events_by_type(int type)
+static int get_n_events_by_type(int type)
 {
 	BUG_ON(type != EV_SW && type != EV_KEY);
 
 	return (type == EV_KEY) ? KEY_CNT : SW_CNT;
 }
 
+/**
+ * get_bm_events_by_type() - returns bitmap of supported events per @type
+ * @input: input device from which bitmap is retrieved
+ * @type: type of button (%EV_KEY, %EV_SW)
+ *
+ * Return value of this function can be used to allocate bitmap
+ * large enough to hold all bits for given type.
+ */
+static const unsigned long *get_bm_events_by_type(struct input_dev *dev,
+						  int type)
+{
+	BUG_ON(type != EV_SW && type != EV_KEY);
+
+	return (type == EV_KEY) ? dev->keybit : dev->swbit;
+}
+
 /**
  * gpio_keys_disable_button() - disables given GPIO button
  * @bdata: button data for button to be disabled
@@ -213,6 +229,7 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 					   const char *buf, unsigned int type)
 {
 	int n_events = get_n_events_by_type(type);
+	const unsigned long *bitmap = get_bm_events_by_type(ddata->input, type);
 	unsigned long *bits;
 	ssize_t error;
 	int i;
@@ -226,6 +243,11 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 		goto out;
 
 	/* First validate */
+	if (!bitmap_subset(bits, bitmap, n_events)) {
+		error = -EINVAL;
+		goto out;
+	}
+
 	for (i = 0; i < ddata->pdata->nbuttons; i++) {
 		struct gpio_button_data *bdata = &ddata->data[i];
 
@@ -239,11 +261,6 @@ static ssize_t gpio_keys_attr_store_helper(struct gpio_keys_drvdata *ddata,
 		}
 	}
 
-	if (i == ddata->pdata->nbuttons) {
-		error = -EINVAL;
-		goto out;
-	}
-
 	mutex_lock(&ddata->disable_lock);
 
 	for (i = 0; i < ddata->pdata->nbuttons; i++) {

drivers/input/keyboard/omap-keypad.c

@@ -155,14 +155,6 @@ static void omap_kp_tasklet(unsigned long data)
 			       "pressed" : "released");
 #else
 			key = keycodes[MATRIX_SCAN_CODE(row, col, row_shift)];
-			if (key < 0) {
-				printk(KERN_WARNING
-				      "omap-keypad: Spurious key event %d-%d\n",
-				       col, row);
-				/* We scan again after a couple of seconds */
-				spurious = 1;
-				continue;
-			}
 
 			if (!(kp_cur_group == (key & GROUP_MASK) ||
 			      kp_cur_group == -1))
@@ -292,8 +284,8 @@ static int omap_kp_probe(struct platform_device *pdev)
 	setup_timer(&omap_kp->timer, omap_kp_timer, (unsigned long)omap_kp);
 
 	/* get the irq and init timer*/
-	tasklet_enable(&kp_tasklet);
 	kp_tasklet.data = (unsigned long) omap_kp;
+	tasklet_enable(&kp_tasklet);
 
 	ret = device_create_file(&pdev->dev, &dev_attr_enable);
 	if (ret < 0)

drivers/input/misc/bma150.c

@@ -147,7 +147,7 @@ struct bma150_data {
  * are stated and verified by Bosch Sensortec where they are configured
  * to provide a generic sensitivity performance.
  */
-static struct bma150_cfg default_cfg = {
+static const struct bma150_cfg default_cfg = {
 	.any_motion_int = 1,
 	.hg_int = 1,
 	.lg_int = 1,

drivers/input/misc/da9063_onkey.c

@@ -179,13 +179,13 @@ static irqreturn_t da9063_onkey_irq_handler(int irq, void *data)
 		input_report_key(onkey->input, KEY_POWER, 1);
 		input_sync(onkey->input);
 		schedule_delayed_work(&onkey->work, 0);
-		dev_dbg(onkey->dev, "KEY_POWER pressed.\n");
+		dev_dbg(onkey->dev, "KEY_POWER long press.\n");
 	} else {
-		input_report_key(onkey->input, KEY_SLEEP, 1);
+		input_report_key(onkey->input, KEY_POWER, 1);
 		input_sync(onkey->input);
-		input_report_key(onkey->input, KEY_SLEEP, 0);
+		input_report_key(onkey->input, KEY_POWER, 0);
 		input_sync(onkey->input);
-		dev_dbg(onkey->dev, "KEY_SLEEP pressed.\n");
+		dev_dbg(onkey->dev, "KEY_POWER short press.\n");
 	}
 
 	return IRQ_HANDLED;

drivers/input/misc/sparcspkr.c

@@ -345,23 +345,19 @@ static struct platform_driver grover_beep_driver = {
 	.shutdown	= sparcspkr_shutdown,
 };
 
+static struct platform_driver * const drivers[] = {
+	&bbc_beep_driver,
+	&grover_beep_driver,
+};
+
 static int __init sparcspkr_init(void)
 {
-	int err = platform_driver_register(&bbc_beep_driver);
-
-	if (!err) {
-		err = platform_driver_register(&grover_beep_driver);
-		if (err)
-			platform_driver_unregister(&bbc_beep_driver);
-	}
-
-	return err;
+	return platform_register_drivers(drivers, ARRAY_SIZE(drivers));
 }
 
 static void __exit sparcspkr_exit(void)
 {
-	platform_driver_unregister(&bbc_beep_driver);
-	platform_driver_unregister(&grover_beep_driver);
+	platform_unregister_drivers(drivers, ARRAY_SIZE(drivers));
 }
 
 module_init(sparcspkr_init);

drivers/input/misc/uinput.c

@@ -256,13 +256,29 @@ static void uinput_destroy_device(struct uinput_device *udev)
 static int uinput_create_device(struct uinput_device *udev)
 {
 	struct input_dev *dev = udev->dev;
-	int error;
+	int error, nslot;
 
 	if (udev->state != UIST_SETUP_COMPLETE) {
 		printk(KERN_DEBUG "%s: write device info first\n", UINPUT_NAME);
 		return -EINVAL;
 	}
 
+	if (test_bit(ABS_MT_SLOT, dev->absbit)) {
+		nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1;
+		error = input_mt_init_slots(dev, nslot, 0);
+		if (error)
+			goto fail1;
+	} else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) {
+		input_set_events_per_packet(dev, 60);
+	}
+
+	if (test_bit(EV_FF, dev->evbit) && !udev->ff_effects_max) {
+		printk(KERN_DEBUG "%s: ff_effects_max should be non-zero when FF_BIT is set\n",
+			UINPUT_NAME);
+		error = -EINVAL;
+		goto fail1;
+	}
+
 	if (udev->ff_effects_max) {
 		error = input_ff_create(dev, udev->ff_effects_max);
 		if (error)
@@ -308,51 +324,50 @@ static int uinput_open(struct inode *inode, struct file *file)
 	return 0;
 }
 
-static int uinput_validate_absbits(struct input_dev *dev)
+static int uinput_validate_absinfo(struct input_dev *dev, unsigned int code,
+				   const struct input_absinfo *abs)
 {
-	unsigned int cnt;
-	int nslot;
-
-	if (!test_bit(EV_ABS, dev->evbit))
-		return 0;
-
-	/*
-	 * Check if absmin/absmax/absfuzz/absflat are sane.
-	 */
-
-	for_each_set_bit(cnt, dev->absbit, ABS_CNT) {
 	int min, max;
 
-		min = input_abs_get_min(dev, cnt);
-		max = input_abs_get_max(dev, cnt);
+	min = abs->minimum;
+	max = abs->maximum;
 
 	if ((min != 0 || max != 0) && max <= min) {
 		printk(KERN_DEBUG
 		       "%s: invalid abs[%02x] min:%d max:%d\n",
-				UINPUT_NAME, cnt,
-				input_abs_get_min(dev, cnt),
-				input_abs_get_max(dev, cnt));
+		       UINPUT_NAME, code, min, max);
 		return -EINVAL;
 	}
 
-		if (input_abs_get_flat(dev, cnt) >
-		    input_abs_get_max(dev, cnt) - input_abs_get_min(dev, cnt)) {
+	if (abs->flat > max - min) {
 		printk(KERN_DEBUG
-				"%s: abs_flat #%02x out of range: %d "
-				"(min:%d/max:%d)\n",
-				UINPUT_NAME, cnt,
-				input_abs_get_flat(dev, cnt),
-				input_abs_get_min(dev, cnt),
-				input_abs_get_max(dev, cnt));
+		       "%s: abs_flat #%02x out of range: %d (min:%d/max:%d)\n",
+		       UINPUT_NAME, code, abs->flat, min, max);
 		return -EINVAL;
 	}
-	}
 
-	if (test_bit(ABS_MT_SLOT, dev->absbit)) {
-		nslot = input_abs_get_max(dev, ABS_MT_SLOT) + 1;
-		input_mt_init_slots(dev, nslot, 0);
-	} else if (test_bit(ABS_MT_POSITION_X, dev->absbit)) {
-		input_set_events_per_packet(dev, 60);
+	return 0;
+}
+
+static int uinput_validate_absbits(struct input_dev *dev)
+{
+	unsigned int cnt;
+	int error;
+
+	if (!test_bit(EV_ABS, dev->evbit))
+		return 0;
+
+	/*
+	 * Check if absmin/absmax/absfuzz/absflat are sane.
+	 */
+
+	for_each_set_bit(cnt, dev->absbit, ABS_CNT) {
+		if (!dev->absinfo)
+			return -EINVAL;
+
+		error = uinput_validate_absinfo(dev, cnt, &dev->absinfo[cnt]);
+		if (error)
+			return error;
 	}
 
 	return 0;
@@ -370,7 +385,70 @@ static int uinput_allocate_device(struct uinput_device *udev)
 	return 0;
 }
 
-static int uinput_setup_device(struct uinput_device *udev,
+static int uinput_dev_setup(struct uinput_device *udev,
+			    struct uinput_setup __user *arg)
+{
+	struct uinput_setup setup;
+	struct input_dev *dev;
+
+	if (udev->state == UIST_CREATED)
+		return -EINVAL;
+
+	if (copy_from_user(&setup, arg, sizeof(setup)))
+		return -EFAULT;
+
+	if (!setup.name[0])
+		return -EINVAL;
+
+	dev = udev->dev;
+	dev->id = setup.id;
+	udev->ff_effects_max = setup.ff_effects_max;
+
+	kfree(dev->name);
+	dev->name = kstrndup(setup.name, UINPUT_MAX_NAME_SIZE, GFP_KERNEL);
+	if (!dev->name)
+		return -ENOMEM;
+
+	udev->state = UIST_SETUP_COMPLETE;
+	return 0;
+}
+
+static int uinput_abs_setup(struct uinput_device *udev,
+			    struct uinput_setup __user *arg, size_t size)
+{
+	struct uinput_abs_setup setup = {};
+	struct input_dev *dev;
+	int error;
+
+	if (size > sizeof(setup))
+		return -E2BIG;
+
+	if (udev->state == UIST_CREATED)
+		return -EINVAL;
+
+	if (copy_from_user(&setup, arg, size))
+		return -EFAULT;
+
+	if (setup.code > ABS_MAX)
+		return -ERANGE;
+
+	dev = udev->dev;
+
+	error = uinput_validate_absinfo(dev, setup.code, &setup.absinfo);
+	if (error)
+		return error;
+
+	input_alloc_absinfo(dev);
+	if (!dev->absinfo)
+		return -ENOMEM;
+
+	set_bit(setup.code, dev->absbit);
+	dev->absinfo[setup.code] = setup.absinfo;
+	return 0;
+}
+
+/* legacy setup via write() */
+static int uinput_setup_device_legacy(struct uinput_device *udev,
 				      const char __user *buffer, size_t count)
 {
 	struct uinput_user_dev	*user_dev;
@@ -474,7 +552,7 @@ static ssize_t uinput_write(struct file *file, const char __user *buffer,
 
 	retval = udev->state == UIST_CREATED ?
 			uinput_inject_events(udev, buffer, count) :
-			uinput_setup_device(udev, buffer, count);
+			uinput_setup_device_legacy(udev, buffer, count);
 
 	mutex_unlock(&udev->mutex);
 
@@ -735,6 +813,12 @@ static long uinput_ioctl_handler(struct file *file, unsigned int cmd,
 			uinput_destroy_device(udev);
 			goto out;
 
+		case UI_DEV_SETUP:
+			retval = uinput_dev_setup(udev, p);
+			goto out;
+
+		/* UI_ABS_SETUP is handled in the variable size ioctls */
+
 		case UI_SET_EVBIT:
 			retval = uinput_set_bit(arg, evbit, EV_MAX);
 			goto out;
@@ -879,6 +963,10 @@ static long uinput_ioctl_handler(struct file *file, unsigned int cmd,
 		name = dev_name(&udev->dev->dev);
 		retval = uinput_str_to_user(p, name, size);
 		goto out;
+
+	case UI_ABS_SETUP & ~IOCSIZE_MASK:
+		retval = uinput_abs_setup(udev, p, size);
+		goto out;
 	}
 
 	retval = -EINVAL;

drivers/input/mouse/alps.c

@@ -31,6 +31,7 @@
 #define ALPS_CMD_NIBBLE_10	0x01f2
 
 #define ALPS_REG_BASE_RUSHMORE	0xc2c0
+#define ALPS_REG_BASE_V7	0xc2c0
 #define ALPS_REG_BASE_PINNACLE	0x0000
 
 static const struct alps_nibble_commands alps_v3_nibble_commands[] = {
@@ -2047,7 +2048,7 @@ static int alps_absolute_mode_v3(struct psmouse *psmouse)
 	return 0;
 }
 
-static int alps_probe_trackstick_v3(struct psmouse *psmouse, int reg_base)
+static int alps_probe_trackstick_v3_v7(struct psmouse *psmouse, int reg_base)
 {
 	int ret = -EIO, reg_val;
 
@@ -2128,15 +2129,12 @@ static int alps_setup_trackstick_v3(struct psmouse *psmouse, int reg_base)
 
 static int alps_hw_init_v3(struct psmouse *psmouse)
 {
+	struct alps_data *priv = psmouse->private;
 	struct ps2dev *ps2dev = &psmouse->ps2dev;
 	int reg_val;
 	unsigned char param[4];
 
-	reg_val = alps_probe_trackstick_v3(psmouse, ALPS_REG_BASE_PINNACLE);
-	if (reg_val == -EIO)
-		goto error;
-
-	if (reg_val == 0 &&
+	if ((priv->flags & ALPS_DUALPOINT) &&
 	    alps_setup_trackstick_v3(psmouse, ALPS_REG_BASE_PINNACLE) == -EIO)
 		goto error;
 
@@ -2613,6 +2611,11 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		priv->decode_fields = alps_decode_pinnacle;
 		priv->nibble_commands = alps_v3_nibble_commands;
 		priv->addr_command = PSMOUSE_CMD_RESET_WRAP;
+
+		if (alps_probe_trackstick_v3_v7(psmouse,
+						ALPS_REG_BASE_PINNACLE) < 0)
+			priv->flags &= ~ALPS_DUALPOINT;
+
 		break;
 
 	case ALPS_PROTO_V3_RUSHMORE:
@@ -2625,7 +2628,7 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		priv->x_bits = 16;
 		priv->y_bits = 12;
 
-		if (alps_probe_trackstick_v3(psmouse,
+		if (alps_probe_trackstick_v3_v7(psmouse,
 						ALPS_REG_BASE_RUSHMORE) < 0)
 			priv->flags &= ~ALPS_DUALPOINT;
 
@@ -2676,6 +2679,9 @@ static int alps_set_protocol(struct psmouse *psmouse,
 		if (priv->fw_ver[1] != 0xba)
 			priv->flags |= ALPS_BUTTONPAD;
 
+		if (alps_probe_trackstick_v3_v7(psmouse, ALPS_REG_BASE_V7) < 0)
+			priv->flags &= ~ALPS_DUALPOINT;
+
 		break;
 
 	case ALPS_PROTO_V8:

drivers/input/mouse/elantech.c

@@ -1222,7 +1222,7 @@ static int elantech_set_input_params(struct psmouse *psmouse)
 			input_set_abs_params(dev, ABS_TOOL_WIDTH, ETP_WMIN_V2,
 					     ETP_WMAX_V2, 0, 0);
 		}
-		input_mt_init_slots(dev, 2, 0);
+		input_mt_init_slots(dev, 2, INPUT_MT_SEMI_MT);
 		input_set_abs_params(dev, ABS_MT_POSITION_X, x_min, x_max, 0, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_Y, y_min, y_max, 0, 0);
 		break;

drivers/input/mouse/focaltech.c

@@ -49,12 +49,6 @@ int focaltech_detect(struct psmouse *psmouse, bool set_properties)
 	return 0;
 }
 
-static void focaltech_reset(struct psmouse *psmouse)
-{
-	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
-	psmouse_reset(psmouse);
-}
-
 #ifdef CONFIG_MOUSE_PS2_FOCALTECH
 
 /*
@@ -300,6 +294,12 @@ static int focaltech_switch_protocol(struct psmouse *psmouse)
 	return 0;
 }
 
+static void focaltech_reset(struct psmouse *psmouse)
+{
+	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
+	psmouse_reset(psmouse);
+}
+
 static void focaltech_disconnect(struct psmouse *psmouse)
 {
 	focaltech_reset(psmouse);
@@ -456,14 +456,4 @@ int focaltech_init(struct psmouse *psmouse)
 	kfree(priv);
 	return error;
 }
-
-#else /* CONFIG_MOUSE_PS2_FOCALTECH */
-
-int focaltech_init(struct psmouse *psmouse)
-{
-	focaltech_reset(psmouse);
-
-	return 0;
-}
-
 #endif /* CONFIG_MOUSE_PS2_FOCALTECH */

drivers/input/mouse/focaltech.h

@@ -18,6 +18,14 @@
 #define _FOCALTECH_H
 
 int focaltech_detect(struct psmouse *psmouse, bool set_properties);
+
+#ifdef CONFIG_MOUSE_PS2_FOCALTECH
 int focaltech_init(struct psmouse *psmouse);
+#else
+static inline int focaltech_init(struct psmouse *psmouse)
+{
+	return -ENOSYS;
+}
+#endif
 
 #endif

drivers/input/mouse/logips2pp.c

@@ -325,7 +325,7 @@ static void ps2pp_set_model_properties(struct psmouse *psmouse,
  * that support it.
  */
 
-int ps2pp_init(struct psmouse *psmouse, bool set_properties)
+int ps2pp_detect(struct psmouse *psmouse, bool set_properties)
 {
 	struct ps2dev *ps2dev = &psmouse->ps2dev;
 	unsigned char param[4];

drivers/input/mouse/logips2pp.h

@@ -12,9 +12,9 @@
 #define _LOGIPS2PP_H
 
 #ifdef CONFIG_MOUSE_PS2_LOGIPS2PP
-int ps2pp_init(struct psmouse *psmouse, bool set_properties);
+int ps2pp_detect(struct psmouse *psmouse, bool set_properties);
 #else
-inline int ps2pp_init(struct psmouse *psmouse, bool set_properties)
+static inline int ps2pp_detect(struct psmouse *psmouse, bool set_properties)
 {
 	return -ENOSYS;
 }

drivers/input/mouse/psmouse-base.c

@@ -119,6 +119,7 @@ struct psmouse_protocol {
 	enum psmouse_type type;
 	bool maxproto;
 	bool ignore_parity; /* Protocol should ignore parity errors from KBC */
+	bool try_passthru; /* Try protocol also on passthrough ports */
 	const char *name;
 	const char *alias;
 	int (*detect)(struct psmouse *, bool);
@@ -129,7 +130,6 @@ struct psmouse_protocol {
  * psmouse_process_byte() analyzes the PS/2 data stream and reports
  * relevant events to the input module once full packet has arrived.
  */
-
 psmouse_ret_t psmouse_process_byte(struct psmouse *psmouse)
 {
 	struct input_dev *dev = psmouse->dev;
@@ -138,22 +138,16 @@ psmouse_ret_t psmouse_process_byte(struct psmouse *psmouse)
 	if (psmouse->pktcnt < psmouse->pktsize)
 		return PSMOUSE_GOOD_DATA;
 
-/*
- * Full packet accumulated, process it
- */
-
-/*
- * Scroll wheel on IntelliMice, scroll buttons on NetMice
- */
+	/* Full packet accumulated, process it */
 
-	if (psmouse->type == PSMOUSE_IMPS || psmouse->type == PSMOUSE_GENPS)
+	switch (psmouse->type) {
+	case PSMOUSE_IMPS:
+		/* IntelliMouse has scroll wheel */
 		input_report_rel(dev, REL_WHEEL, -(signed char) packet[3]);
+		break;
 
-/*
- * Scroll wheel and buttons on IntelliMouse Explorer
- */
-
-	if (psmouse->type == PSMOUSE_IMEX) {
+	case PSMOUSE_IMEX:
+		/* Scroll wheel and buttons on IntelliMouse Explorer */
 		switch (packet[3] & 0xC0) {
 		case 0x80: /* vertical scroll on IntelliMouse Explorer 4.0 */
 			input_report_rel(dev, REL_WHEEL, (int) (packet[3] & 32) - (int) (packet[3] & 31));
@@ -168,39 +162,42 @@ psmouse_ret_t psmouse_process_byte(struct psmouse *psmouse)
 			input_report_key(dev, BTN_EXTRA, (packet[3] >> 5) & 1);
 			break;
 		}
-	}
+		break;
 
-/*
- * Extra buttons on Genius NewNet 3D
- */
+	case PSMOUSE_GENPS:
+		/* Report scroll buttons on NetMice */
+		input_report_rel(dev, REL_WHEEL, -(signed char) packet[3]);
 
-	if (psmouse->type == PSMOUSE_GENPS) {
+		/* Extra buttons on Genius NewNet 3D */
 		input_report_key(dev, BTN_SIDE, (packet[0] >> 6) & 1);
 		input_report_key(dev, BTN_EXTRA, (packet[0] >> 7) & 1);
-	}
+		break;
 
-/*
- * Extra button on ThinkingMouse
- */
-	if (psmouse->type == PSMOUSE_THINKPS) {
+	case PSMOUSE_THINKPS:
+		/* Extra button on ThinkingMouse */
 		input_report_key(dev, BTN_EXTRA, (packet[0] >> 3) & 1);
-		/* Without this bit of weirdness moving up gives wildly high Y changes. */
+
+		/*
+		 * Without this bit of weirdness moving up gives wildly
+		 * high Y changes.
+		 */
 		packet[1] |= (packet[0] & 0x40) << 1;
-	}
+		break;
 
-/*
- * Cortron PS2 Trackball reports SIDE button on the 4th bit of the first
- * byte.
+	case PSMOUSE_CORTRON:
+		/*
+		 * Cortron PS2 Trackball reports SIDE button in the
+		 * 4th bit of the first byte.
 		 */
-	if (psmouse->type == PSMOUSE_CORTRON) {
 		input_report_key(dev, BTN_SIDE, (packet[0] >> 3) & 1);
 		packet[0] |= 0x08;
-	}
+		break;
 
-/*
- * Generic PS/2 Mouse
- */
+	default:
+		break;
+	}
 
+	/* Generic PS/2 Mouse */
 	input_report_key(dev, BTN_LEFT,    packet[0]       & 1);
 	input_report_key(dev, BTN_MIDDLE, (packet[0] >> 2) & 1);
 	input_report_key(dev, BTN_RIGHT,  (packet[0] >> 1) & 1);
@@ -222,7 +219,6 @@ void psmouse_queue_work(struct psmouse *psmouse, struct delayed_work *work,
 /*
  * __psmouse_set_state() sets new psmouse state and resets all flags.
  */
-
 static inline void __psmouse_set_state(struct psmouse *psmouse, enum psmouse_state new_state)
 {
 	psmouse->state = new_state;
@@ -231,13 +227,11 @@ static inline void __psmouse_set_state(struct psmouse *psmouse, enum psmouse_sta
 	psmouse->last = jiffies;
 }
 
-
 /*
  * psmouse_set_state() sets new psmouse state and resets all flags and
  * counters while holding serio lock so fighting with interrupt handler
  * is not a concern.
  */
-
 void psmouse_set_state(struct psmouse *psmouse, enum psmouse_state new_state)
 {
 	serio_pause_rx(psmouse->ps2dev.serio);
@@ -249,7 +243,6 @@ void psmouse_set_state(struct psmouse *psmouse, enum psmouse_state new_state)
  * psmouse_handle_byte() processes one byte of the input data stream
  * by calling corresponding protocol handler.
  */
-
 static int psmouse_handle_byte(struct psmouse *psmouse)
 {
 	psmouse_ret_t rc = psmouse->protocol_handler(psmouse);
@@ -292,7 +285,6 @@ static int psmouse_handle_byte(struct psmouse *psmouse)
  * psmouse_interrupt() handles incoming characters, either passing them
  * for normal processing or gathering them as command response.
  */
-
 static irqreturn_t psmouse_interrupt(struct serio *serio,
 		unsigned char data, unsigned int flags)
 {
@@ -335,9 +327,8 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 	}
 
 	psmouse->packet[psmouse->pktcnt++] = data;
-/*
- * Check if this is a new device announcement (0xAA 0x00)
- */
+
+	/* Check if this is a new device announcement (0xAA 0x00) */
 	if (unlikely(psmouse->packet[0] == PSMOUSE_RET_BAT && psmouse->pktcnt <= 2)) {
 		if (psmouse->pktcnt == 1) {
 			psmouse->last = jiffies;
@@ -351,9 +342,8 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 			serio_reconnect(serio);
 			goto out;
 		}
-/*
- * Not a new device, try processing first byte normally
- */
+
+		/* Not a new device, try processing first byte normally */
 		psmouse->pktcnt = 1;
 		if (psmouse_handle_byte(psmouse))
 			goto out;
@@ -361,8 +351,9 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 		psmouse->packet[psmouse->pktcnt++] = data;
 	}
 
-/*
- * See if we need to force resync because mouse was idle for too long
+	/*
+	 * See if we need to force resync because mouse was idle for
+	 * too long.
 	 */
 	if (psmouse->state == PSMOUSE_ACTIVATED &&
 	    psmouse->pktcnt == 1 && psmouse->resync_time &&
@@ -380,7 +371,6 @@ static irqreturn_t psmouse_interrupt(struct serio *serio,
 	return IRQ_HANDLED;
 }
 
-
 /*
  * psmouse_sliced_command() sends an extended PS/2 command to the mouse
  * using sliced syntax, understood by advanced devices, such as Logitech
@@ -404,7 +394,6 @@ int psmouse_sliced_command(struct psmouse *psmouse, unsigned char command)
 	return 0;
 }
 
-
 /*
  * psmouse_reset() resets the mouse into power-on state.
  */
@@ -424,7 +413,6 @@ int psmouse_reset(struct psmouse *psmouse)
 /*
  * Here we set the mouse resolution.
  */
-
 void psmouse_set_resolution(struct psmouse *psmouse, unsigned int resolution)
 {
 	static const unsigned char params[] = { 0, 1, 2, 2, 3 };
@@ -441,7 +429,6 @@ void psmouse_set_resolution(struct psmouse *psmouse, unsigned int resolution)
 /*
  * Here we set the mouse report rate.
  */
-
 static void psmouse_set_rate(struct psmouse *psmouse, unsigned int rate)
 {
 	static const unsigned char rates[] = { 200, 100, 80, 60, 40, 20, 10, 0 };
@@ -457,7 +444,6 @@ static void psmouse_set_rate(struct psmouse *psmouse, unsigned int rate)
 /*
  * Here we set the mouse scaling.
  */
-
 static void psmouse_set_scale(struct psmouse *psmouse, enum psmouse_scale scale)
 {
 	ps2_command(&psmouse->ps2dev, NULL,
@@ -468,7 +454,6 @@ static void psmouse_set_scale(struct psmouse *psmouse, enum psmouse_scale scale)
 /*
  * psmouse_poll() - default poll handler. Everyone except for ALPS uses it.
  */
-
 static int psmouse_poll(struct psmouse *psmouse)
 {
 	return ps2_command(&psmouse->ps2dev, psmouse->packet,
@@ -602,7 +587,7 @@ static int im_explorer_detect(struct psmouse *psmouse, bool set_properties)
 	if (param[0] != 4)
 		return -1;
 
-/* Magic to enable horizontal scrolling on IntelliMouse 4.0 */
+	/* Magic to enable horizontal scrolling on IntelliMouse 4.0 */
 	param[0] = 200;
 	ps2_command(ps2dev, param, PSMOUSE_CMD_SETRATE);
 	param[0] =  80;
@@ -672,7 +657,7 @@ static int ps2bare_detect(struct psmouse *psmouse, bool set_properties)
 		if (!psmouse->name)
 			psmouse->name = "Mouse";
 
-/*
+		/*
 		 * We have no way of figuring true number of buttons so let's
 		 * assume that the device has 3.
 		 */
@@ -699,284 +684,6 @@ static int cortron_detect(struct psmouse *psmouse, bool set_properties)
 	return 0;
 }
 
-/*
- * Apply default settings to the psmouse structure. Most of them will
- * be overridden by individual protocol initialization routines.
- */
-
-static void psmouse_apply_defaults(struct psmouse *psmouse)
-{
-	struct input_dev *input_dev = psmouse->dev;
-
-	memset(input_dev->evbit, 0, sizeof(input_dev->evbit));
-	memset(input_dev->keybit, 0, sizeof(input_dev->keybit));
-	memset(input_dev->relbit, 0, sizeof(input_dev->relbit));
-	memset(input_dev->absbit, 0, sizeof(input_dev->absbit));
-	memset(input_dev->mscbit, 0, sizeof(input_dev->mscbit));
-
-	__set_bit(EV_KEY, input_dev->evbit);
-	__set_bit(EV_REL, input_dev->evbit);
-
-	__set_bit(BTN_LEFT, input_dev->keybit);
-	__set_bit(BTN_RIGHT, input_dev->keybit);
-
-	__set_bit(REL_X, input_dev->relbit);
-	__set_bit(REL_Y, input_dev->relbit);
-
-	__set_bit(INPUT_PROP_POINTER, input_dev->propbit);
-
-	psmouse->set_rate = psmouse_set_rate;
-	psmouse->set_resolution = psmouse_set_resolution;
-	psmouse->set_scale = psmouse_set_scale;
-	psmouse->poll = psmouse_poll;
-	psmouse->protocol_handler = psmouse_process_byte;
-	psmouse->pktsize = 3;
-	psmouse->reconnect = NULL;
-	psmouse->disconnect = NULL;
-	psmouse->cleanup = NULL;
-	psmouse->pt_activate = NULL;
-	psmouse->pt_deactivate = NULL;
-}
-
-/*
- * Apply default settings to the psmouse structure and call specified
- * protocol detection or initialization routine.
- */
-static int psmouse_do_detect(int (*detect)(struct psmouse *psmouse,
-					   bool set_properties),
-			     struct psmouse *psmouse, bool set_properties)
-{
-	if (set_properties)
-		psmouse_apply_defaults(psmouse);
-
-	return detect(psmouse, set_properties);
-}
-
-/*
- * psmouse_extensions() probes for any extensions to the basic PS/2 protocol
- * the mouse may have.
- */
-
-static int psmouse_extensions(struct psmouse *psmouse,
-			      unsigned int max_proto, bool set_properties)
-{
-	bool synaptics_hardware = false;
-
-/* Always check for focaltech, this is safe as it uses pnp-id matching */
-	if (psmouse_do_detect(focaltech_detect, psmouse, set_properties) == 0) {
-		if (max_proto > PSMOUSE_IMEX) {
-			if (!set_properties || focaltech_init(psmouse) == 0) {
-				if (IS_ENABLED(CONFIG_MOUSE_PS2_FOCALTECH))
-					return PSMOUSE_FOCALTECH;
-				/*
-				 * Note that we need to also restrict
-				 * psmouse_max_proto so that psmouse_initialize()
-				 * does not try to reset rate and resolution,
-				 * because even that upsets the device.
-				 */
-				psmouse_max_proto = PSMOUSE_PS2;
-				return PSMOUSE_PS2;
-			}
-		}
-	}
-
-/*
- * We always check for lifebook because it does not disturb mouse
- * (it only checks DMI information).
- */
-	if (psmouse_do_detect(lifebook_detect, psmouse, set_properties) == 0) {
-		if (max_proto > PSMOUSE_IMEX) {
-			if (!set_properties || lifebook_init(psmouse) == 0)
-				return PSMOUSE_LIFEBOOK;
-		}
-	}
-
-	if (psmouse_do_detect(vmmouse_detect, psmouse, set_properties) == 0) {
-		if (max_proto > PSMOUSE_IMEX) {
-			if (!set_properties || vmmouse_init(psmouse) == 0)
-				return PSMOUSE_VMMOUSE;
-		}
-	}
-
-/*
- * Try Kensington ThinkingMouse (we try first, because synaptics probe
- * upsets the thinkingmouse).
- */
-
-	if (max_proto > PSMOUSE_IMEX &&
-	    psmouse_do_detect(thinking_detect, psmouse, set_properties) == 0) {
-		return PSMOUSE_THINKPS;
-	}
-
-/*
- * Try Synaptics TouchPad. Note that probing is done even if Synaptics protocol
- * support is disabled in config - we need to know if it is synaptics so we
- * can reset it properly after probing for intellimouse.
- */
-	if (max_proto > PSMOUSE_PS2 &&
-	    psmouse_do_detect(synaptics_detect, psmouse, set_properties) == 0) {
-		synaptics_hardware = true;
-
-		if (max_proto > PSMOUSE_IMEX) {
-/*
- * Try activating protocol, but check if support is enabled first, since
- * we try detecting Synaptics even when protocol is disabled.
- */
-			if (IS_ENABLED(CONFIG_MOUSE_PS2_SYNAPTICS) &&
-			    (!set_properties || synaptics_init(psmouse) == 0)) {
-				return PSMOUSE_SYNAPTICS;
-			}
-
-/*
- * Some Synaptics touchpads can emulate extended protocols (like IMPS/2).
- * Unfortunately Logitech/Genius probes confuse some firmware versions so
- * we'll have to skip them.
- */
-			max_proto = PSMOUSE_IMEX;
-		}
-/*
- * Make sure that touchpad is in relative mode, gestures (taps) are enabled
- */
-		synaptics_reset(psmouse);
-	}
-
-/*
- * Try Cypress Trackpad.
- * Must try it before Finger Sensing Pad because Finger Sensing Pad probe
- * upsets some modules of Cypress Trackpads.
- */
-	if (max_proto > PSMOUSE_IMEX &&
-			cypress_detect(psmouse, set_properties) == 0) {
-		if (IS_ENABLED(CONFIG_MOUSE_PS2_CYPRESS)) {
-			if (cypress_init(psmouse) == 0)
-				return PSMOUSE_CYPRESS;
-
-			/*
-			 * Finger Sensing Pad probe upsets some modules of
-			 * Cypress Trackpad, must avoid Finger Sensing Pad
-			 * probe if Cypress Trackpad device detected.
-			 */
-			return PSMOUSE_PS2;
-		}
-
-		max_proto = PSMOUSE_IMEX;
-	}
-
-/*
- * Try ALPS TouchPad
- */
-	if (max_proto > PSMOUSE_IMEX) {
-		ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
-		if (psmouse_do_detect(alps_detect,
-				      psmouse, set_properties) == 0) {
-			if (!set_properties || alps_init(psmouse) == 0)
-				return PSMOUSE_ALPS;
-/*
- * Init failed, try basic relative protocols
- */
-			max_proto = PSMOUSE_IMEX;
-		}
-	}
-
-/*
- * Try OLPC HGPK touchpad.
- */
-	if (max_proto > PSMOUSE_IMEX &&
-	    psmouse_do_detect(hgpk_detect, psmouse, set_properties) == 0) {
-		if (!set_properties || hgpk_init(psmouse) == 0)
-			return PSMOUSE_HGPK;
-/*
- * Init failed, try basic relative protocols
- */
-		max_proto = PSMOUSE_IMEX;
-	}
-
-/*
- * Try Elantech touchpad.
- */
-	if (max_proto > PSMOUSE_IMEX &&
-	    psmouse_do_detect(elantech_detect, psmouse, set_properties) == 0) {
-		if (!set_properties || elantech_init(psmouse) == 0)
-			return PSMOUSE_ELANTECH;
-/*
- * Init failed, try basic relative protocols
- */
-		max_proto = PSMOUSE_IMEX;
-	}
-
-	if (max_proto > PSMOUSE_IMEX) {
-		if (psmouse_do_detect(genius_detect,
-				      psmouse, set_properties) == 0)
-			return PSMOUSE_GENPS;
-
-		if (psmouse_do_detect(ps2pp_init,
-				      psmouse, set_properties) == 0)
-			return PSMOUSE_PS2PP;
-
-		if (psmouse_do_detect(trackpoint_detect,
-				      psmouse, set_properties) == 0)
-			return PSMOUSE_TRACKPOINT;
-
-		if (psmouse_do_detect(touchkit_ps2_detect,
-				      psmouse, set_properties) == 0)
-			return PSMOUSE_TOUCHKIT_PS2;
-	}
-
-/*
- * Try Finger Sensing Pad. We do it here because its probe upsets
- * Trackpoint devices (causing TP_READ_ID command to time out).
- */
-	if (max_proto > PSMOUSE_IMEX) {
-		if (psmouse_do_detect(fsp_detect,
-				      psmouse, set_properties) == 0) {
-			if (!set_properties || fsp_init(psmouse) == 0)
-				return PSMOUSE_FSP;
-/*
- * Init failed, try basic relative protocols
- */
-			max_proto = PSMOUSE_IMEX;
-		}
-	}
-
-/*
- * Reset to defaults in case the device got confused by extended
- * protocol probes. Note that we follow up with full reset because
- * some mice put themselves to sleep when they see PSMOUSE_RESET_DIS.
- */
-	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
-	psmouse_reset(psmouse);
-
-	if (max_proto >= PSMOUSE_IMEX &&
-	    psmouse_do_detect(im_explorer_detect,
-			      psmouse, set_properties) == 0) {
-		return PSMOUSE_IMEX;
-	}
-
-	if (max_proto >= PSMOUSE_IMPS &&
-	    psmouse_do_detect(intellimouse_detect,
-			      psmouse, set_properties) == 0) {
-		return PSMOUSE_IMPS;
-	}
-
-/*
- * Okay, all failed, we have a standard mouse here. The number of the buttons
- * is still a question, though. We assume 3.
- */
-	psmouse_do_detect(ps2bare_detect, psmouse, set_properties);
-
-	if (synaptics_hardware) {
-/*
- * We detected Synaptics hardware but it did not respond to IMPS/2 probes.
- * We need to reset the touchpad because if there is a track point on the
- * pass through port it could get disabled while probing for protocol
- * extensions.
- */
-		psmouse_reset(psmouse);
-	}
-
-	return PSMOUSE_PS2;
-}
-
 static const struct psmouse_protocol psmouse_protocols[] = {
 	{
 		.type		= PSMOUSE_PS2,
@@ -985,13 +692,14 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 		.maxproto	= true,
 		.ignore_parity	= true,
 		.detect		= ps2bare_detect,
+		.try_passthru	= true,
 	},
 #ifdef CONFIG_MOUSE_PS2_LOGIPS2PP
 	{
 		.type		= PSMOUSE_PS2PP,
 		.name		= "PS2++",
 		.alias		= "logitech",
-		.detect		= ps2pp_init,
+		.detect		= ps2pp_detect,
 	},
 #endif
 	{
@@ -1022,6 +730,7 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 		.maxproto	= true,
 		.ignore_parity	= true,
 		.detect		= intellimouse_detect,
+		.try_passthru	= true,
 	},
 	{
 		.type		= PSMOUSE_IMEX,
@@ -1030,6 +739,7 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 		.maxproto	= true,
 		.ignore_parity	= true,
 		.detect		= im_explorer_detect,
+		.try_passthru	= true,
 	},
 #ifdef CONFIG_MOUSE_PS2_SYNAPTICS
 	{
@@ -1061,6 +771,7 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 		.type		= PSMOUSE_LIFEBOOK,
 		.name		= "LBPS/2",
 		.alias		= "lifebook",
+		.detect		= lifebook_detect,
 		.init		= lifebook_init,
 	},
 #endif
@@ -1070,6 +781,7 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 		.name		= "TPPS/2",
 		.alias		= "trackpoint",
 		.detect		= trackpoint_detect,
+		.try_passthru	= true,
 	},
 #endif
 #ifdef CONFIG_MOUSE_PS2_TOUCHKIT
@@ -1138,7 +850,7 @@ static const struct psmouse_protocol psmouse_protocols[] = {
 	},
 };
 
-static const struct psmouse_protocol *psmouse_protocol_by_type(enum psmouse_type type)
+static const struct psmouse_protocol *__psmouse_protocol_by_type(enum psmouse_type type)
 {
 	int i;
 
@@ -1146,6 +858,17 @@ static const struct psmouse_protocol *psmouse_protocol_by_type(enum psmouse_type
 		if (psmouse_protocols[i].type == type)
 			return &psmouse_protocols[i];
 
+	return NULL;
+}
+
+static const struct psmouse_protocol *psmouse_protocol_by_type(enum psmouse_type type)
+{
+	const struct psmouse_protocol *proto;
+
+	proto = __psmouse_protocol_by_type(type);
+	if (proto)
+		return proto;
+
 	WARN_ON(1);
 	return &psmouse_protocols[0];
 }
@@ -1166,23 +889,288 @@ static const struct psmouse_protocol *psmouse_protocol_by_name(const char *name,
 	return NULL;
 }
 
+/*
+ * Apply default settings to the psmouse structure. Most of them will
+ * be overridden by individual protocol initialization routines.
+ */
+static void psmouse_apply_defaults(struct psmouse *psmouse)
+{
+	struct input_dev *input_dev = psmouse->dev;
+
+	memset(input_dev->evbit, 0, sizeof(input_dev->evbit));
+	memset(input_dev->keybit, 0, sizeof(input_dev->keybit));
+	memset(input_dev->relbit, 0, sizeof(input_dev->relbit));
+	memset(input_dev->absbit, 0, sizeof(input_dev->absbit));
+	memset(input_dev->mscbit, 0, sizeof(input_dev->mscbit));
+
+	__set_bit(EV_KEY, input_dev->evbit);
+	__set_bit(EV_REL, input_dev->evbit);
+
+	__set_bit(BTN_LEFT, input_dev->keybit);
+	__set_bit(BTN_RIGHT, input_dev->keybit);
+
+	__set_bit(REL_X, input_dev->relbit);
+	__set_bit(REL_Y, input_dev->relbit);
+
+	__set_bit(INPUT_PROP_POINTER, input_dev->propbit);
+
+	psmouse->set_rate = psmouse_set_rate;
+	psmouse->set_resolution = psmouse_set_resolution;
+	psmouse->set_scale = psmouse_set_scale;
+	psmouse->poll = psmouse_poll;
+	psmouse->protocol_handler = psmouse_process_byte;
+	psmouse->pktsize = 3;
+	psmouse->reconnect = NULL;
+	psmouse->disconnect = NULL;
+	psmouse->cleanup = NULL;
+	psmouse->pt_activate = NULL;
+	psmouse->pt_deactivate = NULL;
+}
+
+static bool psmouse_try_protocol(struct psmouse *psmouse,
+				 enum psmouse_type type,
+				 unsigned int *max_proto,
+				 bool set_properties, bool init_allowed)
+{
+	const struct psmouse_protocol *proto;
+
+	proto = __psmouse_protocol_by_type(type);
+	if (!proto)
+		return false;
+
+	if (psmouse->ps2dev.serio->id.type == SERIO_PS_PSTHRU &&
+	    !proto->try_passthru) {
+		return false;
+	}
+
+	if (set_properties)
+		psmouse_apply_defaults(psmouse);
+
+	if (proto->detect(psmouse, set_properties) != 0)
+		return false;
+
+	if (set_properties && proto->init && init_allowed) {
+		if (proto->init(psmouse) != 0) {
+			/*
+			 * We detected device, but init failed. Adjust
+			 * max_proto so we only try standard protocols.
+			 */
+			if (*max_proto > PSMOUSE_IMEX)
+				*max_proto = PSMOUSE_IMEX;
+
+			return false;
+		}
+	}
+
+	return true;
+}
 
 /*
- * psmouse_probe() probes for a PS/2 mouse.
+ * psmouse_extensions() probes for any extensions to the basic PS/2 protocol
+ * the mouse may have.
  */
+static int psmouse_extensions(struct psmouse *psmouse,
+			      unsigned int max_proto, bool set_properties)
+{
+	bool synaptics_hardware = false;
 
+	/*
+	 * Always check for focaltech, this is safe as it uses pnp-id
+	 * matching.
+	 */
+	if (psmouse_try_protocol(psmouse, PSMOUSE_FOCALTECH,
+				 &max_proto, set_properties, false)) {
+		if (max_proto > PSMOUSE_IMEX &&
+		    IS_ENABLED(CONFIG_MOUSE_PS2_FOCALTECH) &&
+		    (!set_properties || focaltech_init(psmouse) == 0)) {
+			return PSMOUSE_FOCALTECH;
+		}
+		/*
+		 * Restrict psmouse_max_proto so that psmouse_initialize()
+		 * does not try to reset rate and resolution, because even
+		 * that upsets the device.
+		 * This also causes us to basically fall through to basic
+		 * protocol detection, where we fully reset the mouse,
+		 * and set it up as bare PS/2 protocol device.
+		 */
+		psmouse_max_proto = max_proto = PSMOUSE_PS2;
+	}
+
+	/*
+	 * We always check for LifeBook because it does not disturb mouse
+	 * (it only checks DMI information).
+	 */
+	if (psmouse_try_protocol(psmouse, PSMOUSE_LIFEBOOK, &max_proto,
+				 set_properties, max_proto > PSMOUSE_IMEX))
+		return PSMOUSE_LIFEBOOK;
+
+	if (psmouse_try_protocol(psmouse, PSMOUSE_VMMOUSE, &max_proto,
+				 set_properties, max_proto > PSMOUSE_IMEX))
+		return PSMOUSE_VMMOUSE;
+
+	/*
+	 * Try Kensington ThinkingMouse (we try first, because Synaptics
+	 * probe upsets the ThinkingMouse).
+	 */
+	if (max_proto > PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_THINKPS, &max_proto,
+				 set_properties, true)) {
+		return PSMOUSE_THINKPS;
+	}
+
+	/*
+	 * Try Synaptics TouchPad. Note that probing is done even if
+	 * Synaptics protocol support is disabled in config - we need to
+	 * know if it is Synaptics so we can reset it properly after
+	 * probing for IntelliMouse.
+	 */
+	if (max_proto > PSMOUSE_PS2 &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_SYNAPTICS, &max_proto,
+				 set_properties, false)) {
+		synaptics_hardware = true;
+
+		if (max_proto > PSMOUSE_IMEX) {
+			/*
+			 * Try activating protocol, but check if support is
+			 * enabled first, since we try detecting Synaptics
+			 * even when protocol is disabled.
+			 */
+			if (IS_ENABLED(CONFIG_MOUSE_PS2_SYNAPTICS) &&
+			    (!set_properties || synaptics_init(psmouse) == 0)) {
+				return PSMOUSE_SYNAPTICS;
+			}
+
+			/*
+			 * Some Synaptics touchpads can emulate extended
+			 * protocols (like IMPS/2).  Unfortunately
+			 * Logitech/Genius probes confuse some firmware
+			 * versions so we'll have to skip them.
+			 */
+			max_proto = PSMOUSE_IMEX;
+		}
+
+		/*
+		 * Make sure that touchpad is in relative mode, gestures
+		 * (taps) are enabled.
+		 */
+		synaptics_reset(psmouse);
+	}
+
+	/*
+	 * Try Cypress Trackpad. We must try it before Finger Sensing Pad
+	 * because Finger Sensing Pad probe upsets some modules of Cypress
+	 * Trackpads.
+	 */
+	if (max_proto > PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_CYPRESS, &max_proto,
+				 set_properties, true)) {
+		return PSMOUSE_CYPRESS;
+	}
+
+	/* Try ALPS TouchPad */
+	if (max_proto > PSMOUSE_IMEX) {
+		ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
+		if (psmouse_try_protocol(psmouse, PSMOUSE_ALPS,
+					 &max_proto, set_properties, true))
+			return PSMOUSE_ALPS;
+	}
+
+	/* Try OLPC HGPK touchpad */
+	if (max_proto > PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_HGPK, &max_proto,
+				 set_properties, true)) {
+		return PSMOUSE_HGPK;
+	}
+
+	/* Try Elantech touchpad */
+	if (max_proto > PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_ELANTECH,
+				 &max_proto, set_properties, true)) {
+		return PSMOUSE_ELANTECH;
+	}
+
+	if (max_proto > PSMOUSE_IMEX) {
+		if (psmouse_try_protocol(psmouse, PSMOUSE_GENPS,
+					 &max_proto, set_properties, true))
+			return PSMOUSE_GENPS;
+
+		if (psmouse_try_protocol(psmouse, PSMOUSE_PS2PP,
+					 &max_proto, set_properties, true))
+			return PSMOUSE_PS2PP;
+
+		if (psmouse_try_protocol(psmouse, PSMOUSE_TRACKPOINT,
+					 &max_proto, set_properties, true))
+			return PSMOUSE_TRACKPOINT;
+
+		if (psmouse_try_protocol(psmouse, PSMOUSE_TOUCHKIT_PS2,
+					 &max_proto, set_properties, true))
+			return PSMOUSE_TOUCHKIT_PS2;
+	}
+
+	/*
+	 * Try Finger Sensing Pad. We do it here because its probe upsets
+	 * Trackpoint devices (causing TP_READ_ID command to time out).
+	 */
+	if (max_proto > PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_FSP,
+				 &max_proto, set_properties, true)) {
+		return PSMOUSE_FSP;
+	}
+
+	/*
+	 * Reset to defaults in case the device got confused by extended
+	 * protocol probes. Note that we follow up with full reset because
+	 * some mice put themselves to sleep when they see PSMOUSE_RESET_DIS.
+	 */
+	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
+	psmouse_reset(psmouse);
+
+	if (max_proto >= PSMOUSE_IMEX &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_IMEX,
+				 &max_proto, set_properties, true)) {
+		return PSMOUSE_IMEX;
+	}
+
+	if (max_proto >= PSMOUSE_IMPS &&
+	    psmouse_try_protocol(psmouse, PSMOUSE_IMPS,
+				 &max_proto, set_properties, true)) {
+		return PSMOUSE_IMPS;
+	}
+
+	/*
+	 * Okay, all failed, we have a standard mouse here. The number of
+	 * the buttons is still a question, though. We assume 3.
+	 */
+	psmouse_try_protocol(psmouse, PSMOUSE_PS2,
+			     &max_proto, set_properties, true);
+
+	if (synaptics_hardware) {
+		/*
+		 * We detected Synaptics hardware but it did not respond to
+		 * IMPS/2 probes.  We need to reset the touchpad because if
+		 * there is a track point on the pass through port it could
+		 * get disabled while probing for protocol extensions.
+		 */
+		psmouse_reset(psmouse);
+	}
+
+	return PSMOUSE_PS2;
+}
+
+/*
+ * psmouse_probe() probes for a PS/2 mouse.
+ */
 static int psmouse_probe(struct psmouse *psmouse)
 {
 	struct ps2dev *ps2dev = &psmouse->ps2dev;
 	unsigned char param[2];
 
-/*
- * First, we check if it's a mouse. It should send 0x00 or 0x03
- * in case of an IntelliMouse in 4-byte mode or 0x04 for IM Explorer.
- * Sunrex K8561 IR Keyboard/Mouse reports 0xff on second and subsequent
- * ID queries, probably due to a firmware bug.
+	/*
+	 * First, we check if it's a mouse. It should send 0x00 or 0x03 in
+	 * case of an IntelliMouse in 4-byte mode or 0x04 for IM Explorer.
+	 * Sunrex K8561 IR Keyboard/Mouse reports 0xff on second and
+	 * subsequent ID queries, probably due to a firmware bug.
 	 */
-
 	param[0] = 0xa5;
 	if (ps2_command(ps2dev, param, PSMOUSE_CMD_GETID))
 		return -1;
@@ -1191,10 +1179,10 @@ static int psmouse_probe(struct psmouse *psmouse)
 	    param[0] != 0x04 && param[0] != 0xff)
 		return -1;
 
-/*
- * Then we reset and disable the mouse so that it doesn't generate events.
+	/*
+	 * Then we reset and disable the mouse so that it doesn't generate
+	 * events.
 	 */
-
 	if (ps2_command(ps2dev, NULL, PSMOUSE_CMD_RESET_DIS))
 		psmouse_warn(psmouse, "Failed to reset mouse on %s\n",
 			     ps2dev->serio->phys);
@@ -1205,13 +1193,11 @@ static int psmouse_probe(struct psmouse *psmouse)
 /*
  * psmouse_initialize() initializes the mouse to a sane state.
  */
-
 static void psmouse_initialize(struct psmouse *psmouse)
 {
-/*
+	/*
 	 * We set the mouse report rate, resolution and scaling.
 	 */
-
 	if (psmouse_max_proto != PSMOUSE_PS2) {
 		psmouse->set_rate(psmouse, psmouse->rate);
 		psmouse->set_resolution(psmouse, psmouse->resolution);
@@ -1222,7 +1208,6 @@ static void psmouse_initialize(struct psmouse *psmouse)
 /*
  * psmouse_activate() enables the mouse so that we get motion reports from it.
  */
-
 int psmouse_activate(struct psmouse *psmouse)
 {
 	if (ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_ENABLE)) {
@@ -1236,10 +1221,9 @@ int psmouse_activate(struct psmouse *psmouse)
 }
 
 /*
- * psmouse_deactivate() puts the mouse into poll mode so that we don't get motion
- * reports from it unless we explicitly request it.
+ * psmouse_deactivate() puts the mouse into poll mode so that we don't get
+ * motion reports from it unless we explicitly request it.
  */
-
 int psmouse_deactivate(struct psmouse *psmouse)
 {
 	if (ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_DISABLE)) {
@@ -1252,11 +1236,9 @@ int psmouse_deactivate(struct psmouse *psmouse)
 	return 0;
 }
 
-
 /*
  * psmouse_resync() attempts to re-validate current protocol.
  */
-
 static void psmouse_resync(struct work_struct *work)
 {
 	struct psmouse *parent = NULL, *psmouse =
@@ -1276,7 +1258,7 @@ static void psmouse_resync(struct work_struct *work)
 		psmouse_deactivate(parent);
 	}
 
-/*
+	/*
 	 * Some mice don't ACK commands sent while they are in the middle of
 	 * transmitting motion packet. To avoid delay we use ps2_sendbyte()
 	 * instead of ps2_command() which would wait for 200ms for an ACK
@@ -1294,7 +1276,7 @@ static void psmouse_resync(struct work_struct *work)
 	} else
 		psmouse->acks_disable_command = true;
 
-/*
+	/*
 	 * Poll the mouse. If it was reset the packet will be shorter than
 	 * psmouse->pktsize and ps2_command will fail. We do not expect and
 	 * do not handle scenario when mouse "upgrades" its protocol while
@@ -1317,10 +1299,11 @@ static void psmouse_resync(struct work_struct *work)
 			psmouse_set_state(psmouse, PSMOUSE_RESYNCING);
 		}
 	}
-/*
- * Now try to enable mouse. We try to do that even if poll failed and also
- * repeat our attempts 5 times, otherwise we may be left out with disabled
- * mouse.
+
+	/*
+	 * Now try to enable mouse. We try to do that even if poll failed
+	 * and also repeat our attempts 5 times, otherwise we may be left
+	 * out with disabled mouse.
 	 */
 	for (i = 0; i < 5; i++) {
 		if (!ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_ENABLE)) {
@@ -1353,7 +1336,6 @@ static void psmouse_resync(struct work_struct *work)
 /*
  * psmouse_cleanup() resets the mouse into power-on state.
  */
-
 static void psmouse_cleanup(struct serio *serio)
 {
 	struct psmouse *psmouse = serio_get_drvdata(serio);
@@ -1378,12 +1360,12 @@ static void psmouse_cleanup(struct serio *serio)
 	if (psmouse->cleanup)
 		psmouse->cleanup(psmouse);
 
-/*
+	/*
 	 * Reset the mouse to defaults (bare PS/2 protocol).
 	 */
 	ps2_command(&psmouse->ps2dev, NULL, PSMOUSE_CMD_RESET_DIS);
 
-/*
+	/*
 	 * Some boxes, such as HP nx7400, get terribly confused if mouse
 	 * is not fully enabled before suspending/shutting down.
 	 */
@@ -1402,7 +1384,6 @@ static void psmouse_cleanup(struct serio *serio)
 /*
  * psmouse_disconnect() closes and frees.
  */
-
 static void psmouse_disconnect(struct serio *serio)
 {
 	struct psmouse *psmouse, *parent = NULL;
@@ -1602,7 +1583,6 @@ static int psmouse_connect(struct serio *serio, struct serio_driver *drv)
 	goto out;
 }
 
-
 static int psmouse_reconnect(struct serio *serio)
 {
 	struct psmouse *psmouse = serio_get_drvdata(serio);

drivers/input/serio/i8042-x86ia64io.h

@@ -257,6 +257,13 @@ static const struct dmi_system_id __initconst i8042_dmi_nomux_table[] = {
 			DMI_MATCH(DMI_PRODUCT_NAME, "LifeBook S6230"),
 		},
 	},
+	{
+		/* Fujitsu Lifebook U745 */
+		.matches = {
+			DMI_MATCH(DMI_SYS_VENDOR, "FUJITSU"),
+			DMI_MATCH(DMI_PRODUCT_NAME, "LIFEBOOK U745"),
+		},
+	},
 	{
 		/* Fujitsu T70H */
 		.matches = {

drivers/input/touchscreen/Kconfig

@@ -295,6 +295,16 @@ config TOUCHSCREEN_EGALAX
 	  To compile this driver as a module, choose M here: the
 	  module will be called egalax_ts.
 
+config TOUCHSCREEN_EGALAX_SERIAL
+	tristate "EETI eGalax serial touchscreen"
+	select SERIO
+	help
+	  Say Y here to enable support for serial connected EETI
+	  eGalax touch panels.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called egalax_ts_serial.
+
 config TOUCHSCREEN_FT6236
 	tristate "FT6236 I2C touchscreen"
 	depends on I2C
@@ -324,6 +334,7 @@ config TOUCHSCREEN_FUJITSU
 config TOUCHSCREEN_GOODIX
 	tristate "Goodix I2C touchscreen"
 	depends on I2C
+	depends on GPIOLIB
 	help
 	  Say Y here if you have the Goodix touchscreen (such as one
 	  installed in Onda v975w tablets) connected to your
@@ -927,6 +938,22 @@ config TOUCHSCREEN_TOUCHIT213
 	  To compile this driver as a module, choose M here: the
 	  module will be called touchit213.
 
+config TOUCHSCREEN_TS4800
+	tristate "TS-4800 touchscreen"
+	depends on HAS_IOMEM && OF
+	select MFD_SYSCON
+	select INPUT_POLLDEV
+	help
+	  Say Y here if you have a touchscreen on a TS-4800 board.
+
+	  On TS-4800, the touchscreen is not handled directly by Linux but by
+	  a companion FPGA.
+
+	  If unsure, say N.
+
+	  To compile this driver as a module, choose M here: the
+	  module will be called ts4800_ts.
+
 config TOUCHSCREEN_TSC_SERIO
 	tristate "TSC-10/25/40 serial touchscreen support"
 	select SERIO

drivers/input/touchscreen/Makefile

@@ -35,6 +35,7 @@ obj-$(CONFIG_TOUCHSCREEN_EETI)		+= eeti_ts.o
 obj-$(CONFIG_TOUCHSCREEN_ELAN)		+= elants_i2c.o
 obj-$(CONFIG_TOUCHSCREEN_ELO)		+= elo.o
 obj-$(CONFIG_TOUCHSCREEN_EGALAX)	+= egalax_ts.o
+obj-$(CONFIG_TOUCHSCREEN_EGALAX_SERIAL)	+= egalax_ts_serial.o
 obj-$(CONFIG_TOUCHSCREEN_FT6236)	+= ft6236.o
 obj-$(CONFIG_TOUCHSCREEN_FUJITSU)	+= fujitsu_ts.o
 obj-$(CONFIG_TOUCHSCREEN_GOODIX)	+= goodix.o
@@ -68,6 +69,7 @@ obj-$(CONFIG_TOUCHSCREEN_TI_AM335X_TSC)	+= ti_am335x_tsc.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHIT213)	+= touchit213.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHRIGHT)	+= touchright.o
 obj-$(CONFIG_TOUCHSCREEN_TOUCHWIN)	+= touchwin.o
+obj-$(CONFIG_TOUCHSCREEN_TS4800)	+= ts4800-ts.o
 obj-$(CONFIG_TOUCHSCREEN_TSC_SERIO)	+= tsc40.o
 obj-$(CONFIG_TOUCHSCREEN_TSC200X_CORE)	+= tsc200x-core.o
 obj-$(CONFIG_TOUCHSCREEN_TSC2004)	+= tsc2004.o

drivers/input/touchscreen/egalax_ts_serial.c

+/*
+ * EETI Egalax serial touchscreen driver
+ *
+ * Copyright (c) 2015 Zoltán Böszörményi <zboszor@pr.hu>
+ *
+ * based on the
+ *
+ * Hampshire serial touchscreen driver (Copyright (c) 2010 Adam Bennett)
+ */
+
+/*
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of the GNU General Public License version 2 as published by
+ * the Free Software Foundation.
+ */
+
+#include <linux/errno.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/slab.h>
+#include <linux/input.h>
+#include <linux/serio.h>
+
+#define DRIVER_DESC	"EETI Egalax serial touchscreen driver"
+
+/*
+ * Definitions & global arrays.
+ */
+
+#define EGALAX_FORMAT_MAX_LENGTH	6
+#define EGALAX_FORMAT_START_BIT		BIT(7)
+#define EGALAX_FORMAT_PRESSURE_BIT	BIT(6)
+#define EGALAX_FORMAT_TOUCH_BIT		BIT(0)
+#define EGALAX_FORMAT_RESOLUTION_MASK	0x06
+
+#define EGALAX_MIN_XC			0
+#define EGALAX_MAX_XC			0x4000
+#define EGALAX_MIN_YC			0
+#define EGALAX_MAX_YC			0x4000
+
+/*
+ * Per-touchscreen data.
+ */
+struct egalax {
+	struct input_dev *input;
+	struct serio *serio;
+	int idx;
+	u8 data[EGALAX_FORMAT_MAX_LENGTH];
+	char phys[32];
+};
+
+static void egalax_process_data(struct egalax *egalax)
+{
+	struct input_dev *dev = egalax->input;
+	u8 *data = egalax->data;
+	u16 x, y;
+	u8 shift;
+	u8 mask;
+
+	shift = 3 - ((data[0] & EGALAX_FORMAT_RESOLUTION_MASK) >> 1);
+	mask = 0xff >> (shift + 1);
+
+	x = (((u16)(data[1] & mask) << 7) | (data[2] & 0x7f)) << shift;
+	y = (((u16)(data[3] & mask) << 7) | (data[4] & 0x7f)) << shift;
+
+	input_report_key(dev, BTN_TOUCH, data[0] & EGALAX_FORMAT_TOUCH_BIT);
+	input_report_abs(dev, ABS_X, x);
+	input_report_abs(dev, ABS_Y, y);
+	input_sync(dev);
+}
+
+static irqreturn_t egalax_interrupt(struct serio *serio,
+				    unsigned char data, unsigned int flags)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+	int pkt_len;
+
+	egalax->data[egalax->idx++] = data;
+
+	if (likely(egalax->data[0] & EGALAX_FORMAT_START_BIT)) {
+		pkt_len = egalax->data[0] & EGALAX_FORMAT_PRESSURE_BIT ? 6 : 5;
+		if (pkt_len == egalax->idx) {
+			egalax_process_data(egalax);
+			egalax->idx = 0;
+		}
+	} else {
+		dev_dbg(&serio->dev, "unknown/unsynchronized data: %x\n",
+			egalax->data[0]);
+		egalax->idx = 0;
+	}
+
+	return IRQ_HANDLED;
+}
+
+/*
+ * egalax_connect() is the routine that is called when someone adds a
+ * new serio device that supports egalax protocol and registers it as
+ * an input device. This is usually accomplished using inputattach.
+ */
+static int egalax_connect(struct serio *serio, struct serio_driver *drv)
+{
+	struct egalax *egalax;
+	struct input_dev *input_dev;
+	int error;
+
+	egalax = kzalloc(sizeof(struct egalax), GFP_KERNEL);
+	input_dev = input_allocate_device();
+	if (!egalax || !input_dev) {
+		error = -ENOMEM;
+		goto err_free_mem;
+	}
+
+	egalax->serio = serio;
+	egalax->input = input_dev;
+	snprintf(egalax->phys, sizeof(egalax->phys),
+		 "%s/input0", serio->phys);
+
+	input_dev->name = "EETI eGalaxTouch Serial TouchScreen";
+	input_dev->phys = egalax->phys;
+	input_dev->id.bustype = BUS_RS232;
+	input_dev->id.vendor = SERIO_EGALAX;
+	input_dev->id.product = 0;
+	input_dev->id.version = 0x0001;
+	input_dev->dev.parent = &serio->dev;
+
+	input_set_capability(input_dev, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(input_dev, ABS_X,
+			     EGALAX_MIN_XC, EGALAX_MAX_XC, 0, 0);
+	input_set_abs_params(input_dev, ABS_Y,
+			     EGALAX_MIN_YC, EGALAX_MAX_YC, 0, 0);
+
+	serio_set_drvdata(serio, egalax);
+
+	error = serio_open(serio, drv);
+	if (error)
+		goto err_reset_drvdata;
+
+	error = input_register_device(input_dev);
+	if (error)
+		goto err_close_serio;
+
+	return 0;
+
+err_close_serio:
+	serio_close(serio);
+err_reset_drvdata:
+	serio_set_drvdata(serio, NULL);
+err_free_mem:
+	input_free_device(input_dev);
+	kfree(egalax);
+	return error;
+}
+
+static void egalax_disconnect(struct serio *serio)
+{
+	struct egalax *egalax = serio_get_drvdata(serio);
+
+	serio_close(serio);
+	serio_set_drvdata(serio, NULL);
+	input_unregister_device(egalax->input);
+	kfree(egalax);
+}
+
+/*
+ * The serio driver structure.
+ */
+
+static const struct serio_device_id egalax_serio_ids[] = {
+	{
+		.type	= SERIO_RS232,
+		.proto	= SERIO_EGALAX,
+		.id	= SERIO_ANY,
+		.extra	= SERIO_ANY,
+	},
+	{ 0 }
+};
+
+MODULE_DEVICE_TABLE(serio, egalax_serio_ids);
+
+static struct serio_driver egalax_drv = {
+	.driver		= {
+		.name	= "egalax",
+	},
+	.description	= DRIVER_DESC,
+	.id_table	= egalax_serio_ids,
+	.interrupt	= egalax_interrupt,
+	.connect	= egalax_connect,
+	.disconnect	= egalax_disconnect,
+};
+module_serio_driver(egalax_drv);
+
+MODULE_AUTHOR("Zoltán Böszörményi <zboszor@pr.hu>");
+MODULE_DESCRIPTION(DRIVER_DESC);
+MODULE_LICENSE("GPL v2");

drivers/input/touchscreen/goodix.c

@@ -2,6 +2,7 @@
  *  Driver for Goodix Touchscreens
  *
  *  Copyright (c) 2014 Red Hat Inc.
+ *  Copyright (c) 2015 K. Merker <merker@debian.org>
  *
  *  This code is based on gt9xx.c authored by andrew@goodix.com:
  *
@@ -16,6 +17,8 @@
 
 #include <linux/kernel.h>
 #include <linux/dmi.h>
+#include <linux/firmware.h>
+#include <linux/gpio/consumer.h>
 #include <linux/i2c.h>
 #include <linux/input.h>
 #include <linux/input/mt.h>
@@ -33,11 +36,24 @@ struct goodix_ts_data {
 	struct input_dev *input_dev;
 	int abs_x_max;
 	int abs_y_max;
+	bool swapped_x_y;
+	bool inverted_x;
+	bool inverted_y;
 	unsigned int max_touch_num;
 	unsigned int int_trigger_type;
-	bool rotated_screen;
+	int cfg_len;
+	struct gpio_desc *gpiod_int;
+	struct gpio_desc *gpiod_rst;
+	u16 id;
+	u16 version;
+	const char *cfg_name;
+	struct completion firmware_loading_complete;
+	unsigned long irq_flags;
 };
 
+#define GOODIX_GPIO_INT_NAME		"irq"
+#define GOODIX_GPIO_RST_NAME		"reset"
+
 #define GOODIX_MAX_HEIGHT		4096
 #define GOODIX_MAX_WIDTH		4096
 #define GOODIX_INT_TRIGGER		1
@@ -45,8 +61,13 @@ struct goodix_ts_data {
 #define GOODIX_MAX_CONTACTS		10
 
 #define GOODIX_CONFIG_MAX_LENGTH	240
+#define GOODIX_CONFIG_911_LENGTH	186
+#define GOODIX_CONFIG_967_LENGTH	228
 
 /* Register defines */
+#define GOODIX_REG_COMMAND		0x8040
+#define GOODIX_CMD_SCREEN_OFF		0x05
+
 #define GOODIX_READ_COOR_ADDR		0x814E
 #define GOODIX_REG_CONFIG_DATA		0x8047
 #define GOODIX_REG_ID			0x8140
@@ -115,6 +136,63 @@ static int goodix_i2c_read(struct i2c_client *client,
 	return ret < 0 ? ret : (ret != ARRAY_SIZE(msgs) ? -EIO : 0);
 }
 
+/**
+ * goodix_i2c_write - write data to a register of the i2c slave device.
+ *
+ * @client: i2c device.
+ * @reg: the register to write to.
+ * @buf: raw data buffer to write.
+ * @len: length of the buffer to write
+ */
+static int goodix_i2c_write(struct i2c_client *client, u16 reg, const u8 *buf,
+			    unsigned len)
+{
+	u8 *addr_buf;
+	struct i2c_msg msg;
+	int ret;
+
+	addr_buf = kmalloc(len + 2, GFP_KERNEL);
+	if (!addr_buf)
+		return -ENOMEM;
+
+	addr_buf[0] = reg >> 8;
+	addr_buf[1] = reg & 0xFF;
+	memcpy(&addr_buf[2], buf, len);
+
+	msg.flags = 0;
+	msg.addr = client->addr;
+	msg.buf = addr_buf;
+	msg.len = len + 2;
+
+	ret = i2c_transfer(client->adapter, &msg, 1);
+	kfree(addr_buf);
+	return ret < 0 ? ret : (ret != 1 ? -EIO : 0);
+}
+
+static int goodix_i2c_write_u8(struct i2c_client *client, u16 reg, u8 value)
+{
+	return goodix_i2c_write(client, reg, &value, sizeof(value));
+}
+
+static int goodix_get_cfg_len(u16 id)
+{
+	switch (id) {
+	case 911:
+	case 9271:
+	case 9110:
+	case 927:
+	case 928:
+		return GOODIX_CONFIG_911_LENGTH;
+
+	case 912:
+	case 967:
+		return GOODIX_CONFIG_967_LENGTH;
+
+	default:
+		return GOODIX_CONFIG_MAX_LENGTH;
+	}
+}
+
 static int goodix_ts_read_input_report(struct goodix_ts_data *ts, u8 *data)
 {
 	int touch_num;
@@ -155,10 +233,13 @@ static void goodix_ts_report_touch(struct goodix_ts_data *ts, u8 *coor_data)
 	int input_y = get_unaligned_le16(&coor_data[3]);
 	int input_w = get_unaligned_le16(&coor_data[5]);
 
-	if (ts->rotated_screen) {
+	/* Inversions have to happen before axis swapping */
+	if (ts->inverted_x)
 		input_x = ts->abs_x_max - input_x;
+	if (ts->inverted_y)
 		input_y = ts->abs_y_max - input_y;
-	}
+	if (ts->swapped_x_y)
+		swap(input_x, input_y);
 
 	input_mt_slot(ts->input_dev, id);
 	input_mt_report_slot_state(ts->input_dev, MT_TOOL_FINGER, true);
@@ -202,21 +283,195 @@ static void goodix_process_events(struct goodix_ts_data *ts)
  */
 static irqreturn_t goodix_ts_irq_handler(int irq, void *dev_id)
 {
-	static const u8 end_cmd[] = {
-		GOODIX_READ_COOR_ADDR >> 8,
-		GOODIX_READ_COOR_ADDR & 0xff,
-		0
-	};
 	struct goodix_ts_data *ts = dev_id;
 
 	goodix_process_events(ts);
 
-	if (i2c_master_send(ts->client, end_cmd, sizeof(end_cmd)) < 0)
+	if (goodix_i2c_write_u8(ts->client, GOODIX_READ_COOR_ADDR, 0) < 0)
 		dev_err(&ts->client->dev, "I2C write end_cmd error\n");
 
 	return IRQ_HANDLED;
 }
 
+static void goodix_free_irq(struct goodix_ts_data *ts)
+{
+	devm_free_irq(&ts->client->dev, ts->client->irq, ts);
+}
+
+static int goodix_request_irq(struct goodix_ts_data *ts)
+{
+	return devm_request_threaded_irq(&ts->client->dev, ts->client->irq,
+					 NULL, goodix_ts_irq_handler,
+					 ts->irq_flags, ts->client->name, ts);
+}
+
+/**
+ * goodix_check_cfg - Checks if config fw is valid
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: firmware config data
+ */
+static int goodix_check_cfg(struct goodix_ts_data *ts,
+			    const struct firmware *cfg)
+{
+	int i, raw_cfg_len;
+	u8 check_sum = 0;
+
+	if (cfg->size > GOODIX_CONFIG_MAX_LENGTH) {
+		dev_err(&ts->client->dev,
+			"The length of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	raw_cfg_len = cfg->size - 2;
+	for (i = 0; i < raw_cfg_len; i++)
+		check_sum += cfg->data[i];
+	check_sum = (~check_sum) + 1;
+	if (check_sum != cfg->data[raw_cfg_len]) {
+		dev_err(&ts->client->dev,
+			"The checksum of the config fw is not correct");
+		return -EINVAL;
+	}
+
+	if (cfg->data[raw_cfg_len + 1] != 1) {
+		dev_err(&ts->client->dev,
+			"Config fw must have Config_Fresh register set");
+		return -EINVAL;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_send_cfg - Write fw config to device
+ *
+ * @ts: goodix_ts_data pointer
+ * @cfg: config firmware to write to device
+ */
+static int goodix_send_cfg(struct goodix_ts_data *ts,
+			   const struct firmware *cfg)
+{
+	int error;
+
+	error = goodix_check_cfg(ts, cfg);
+	if (error)
+		return error;
+
+	error = goodix_i2c_write(ts->client, GOODIX_REG_CONFIG_DATA, cfg->data,
+				 cfg->size);
+	if (error) {
+		dev_err(&ts->client->dev, "Failed to write config data: %d",
+			error);
+		return error;
+	}
+	dev_dbg(&ts->client->dev, "Config sent successfully.");
+
+	/* Let the firmware reconfigure itself, so sleep for 10ms */
+	usleep_range(10000, 11000);
+
+	return 0;
+}
+
+static int goodix_int_sync(struct goodix_ts_data *ts)
+{
+	int error;
+
+	error = gpiod_direction_output(ts->gpiod_int, 0);
+	if (error)
+		return error;
+
+	msleep(50);				/* T5: 50ms */
+
+	error = gpiod_direction_input(ts->gpiod_int);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+/**
+ * goodix_reset - Reset device during power on
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_reset(struct goodix_ts_data *ts)
+{
+	int error;
+
+	/* begin select I2C slave addr */
+	error = gpiod_direction_output(ts->gpiod_rst, 0);
+	if (error)
+		return error;
+
+	msleep(20);				/* T2: > 10ms */
+
+	/* HIGH: 0x28/0x29, LOW: 0xBA/0xBB */
+	error = gpiod_direction_output(ts->gpiod_int, ts->client->addr == 0x14);
+	if (error)
+		return error;
+
+	usleep_range(100, 2000);		/* T3: > 100us */
+
+	error = gpiod_direction_output(ts->gpiod_rst, 1);
+	if (error)
+		return error;
+
+	usleep_range(6000, 10000);		/* T4: > 5ms */
+
+	/* end select I2C slave addr */
+	error = gpiod_direction_input(ts->gpiod_rst);
+	if (error)
+		return error;
+
+	error = goodix_int_sync(ts);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+/**
+ * goodix_get_gpio_config - Get GPIO config from ACPI/DT
+ *
+ * @ts: goodix_ts_data pointer
+ */
+static int goodix_get_gpio_config(struct goodix_ts_data *ts)
+{
+	int error;
+	struct device *dev;
+	struct gpio_desc *gpiod;
+
+	if (!ts->client)
+		return -EINVAL;
+	dev = &ts->client->dev;
+
+	/* Get the interrupt GPIO pin number */
+	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_INT_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_INT_NAME, error);
+		return error;
+	}
+
+	ts->gpiod_int = gpiod;
+
+	/* Get the reset line GPIO pin number */
+	gpiod = devm_gpiod_get_optional(dev, GOODIX_GPIO_RST_NAME, GPIOD_IN);
+	if (IS_ERR(gpiod)) {
+		error = PTR_ERR(gpiod);
+		if (error != -EPROBE_DEFER)
+			dev_dbg(dev, "Failed to get %s GPIO: %d\n",
+				GOODIX_GPIO_RST_NAME, error);
+		return error;
+	}
+
+	ts->gpiod_rst = gpiod;
+
+	return 0;
+}
+
 /**
  * goodix_read_config - Read the embedded configuration of the panel
  *
@@ -230,14 +485,15 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 	int error;
 
 	error = goodix_i2c_read(ts->client, GOODIX_REG_CONFIG_DATA,
-				config,
-				GOODIX_CONFIG_MAX_LENGTH);
+				config, ts->cfg_len);
 	if (error) {
 		dev_warn(&ts->client->dev,
 			 "Error reading config (%d), using defaults\n",
 			 error);
 		ts->abs_x_max = GOODIX_MAX_WIDTH;
 		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+		if (ts->swapped_x_y)
+			swap(ts->abs_x_max, ts->abs_y_max);
 		ts->int_trigger_type = GOODIX_INT_TRIGGER;
 		ts->max_touch_num = GOODIX_MAX_CONTACTS;
 		return;
@@ -245,6 +501,8 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 
 	ts->abs_x_max = get_unaligned_le16(&config[RESOLUTION_LOC]);
 	ts->abs_y_max = get_unaligned_le16(&config[RESOLUTION_LOC + 2]);
+	if (ts->swapped_x_y)
+		swap(ts->abs_x_max, ts->abs_y_max);
 	ts->int_trigger_type = config[TRIGGER_LOC] & 0x03;
 	ts->max_touch_num = config[MAX_CONTACTS_LOC] & 0x0f;
 	if (!ts->abs_x_max || !ts->abs_y_max || !ts->max_touch_num) {
@@ -252,42 +510,45 @@ static void goodix_read_config(struct goodix_ts_data *ts)
 			"Invalid config, using defaults\n");
 		ts->abs_x_max = GOODIX_MAX_WIDTH;
 		ts->abs_y_max = GOODIX_MAX_HEIGHT;
+		if (ts->swapped_x_y)
+			swap(ts->abs_x_max, ts->abs_y_max);
 		ts->max_touch_num = GOODIX_MAX_CONTACTS;
 	}
 
-	ts->rotated_screen = dmi_check_system(rotated_screen);
-	if (ts->rotated_screen)
+	if (dmi_check_system(rotated_screen)) {
+		ts->inverted_x = true;
+		ts->inverted_y = true;
 		dev_dbg(&ts->client->dev,
 			 "Applying '180 degrees rotated screen' quirk\n");
+	}
 }
 
 /**
  * goodix_read_version - Read goodix touchscreen version
  *
- * @client: the i2c client
- * @version: output buffer containing the version on success
- * @id: output buffer containing the id on success
+ * @ts: our goodix_ts_data pointer
  */
-static int goodix_read_version(struct i2c_client *client, u16 *version, u16 *id)
+static int goodix_read_version(struct goodix_ts_data *ts)
 {
 	int error;
 	u8 buf[6];
 	char id_str[5];
 
-	error = goodix_i2c_read(client, GOODIX_REG_ID, buf, sizeof(buf));
+	error = goodix_i2c_read(ts->client, GOODIX_REG_ID, buf, sizeof(buf));
 	if (error) {
-		dev_err(&client->dev, "read version failed: %d\n", error);
+		dev_err(&ts->client->dev, "read version failed: %d\n", error);
 		return error;
 	}
 
 	memcpy(id_str, buf, 4);
 	id_str[4] = 0;
-	if (kstrtou16(id_str, 10, id))
-		*id = 0x1001;
+	if (kstrtou16(id_str, 10, &ts->id))
+		ts->id = 0x1001;
 
-	*version = get_unaligned_le16(&buf[4]);
+	ts->version = get_unaligned_le16(&buf[4]);
 
-	dev_info(&client->dev, "ID %d, version: %04x\n", *id, *version);
+	dev_info(&ts->client->dev, "ID %d, version: %04x\n", ts->id,
+		 ts->version);
 
 	return 0;
 }
@@ -321,13 +582,10 @@ static int goodix_i2c_test(struct i2c_client *client)
  * goodix_request_input_dev - Allocate, populate and register the input device
  *
  * @ts: our goodix_ts_data pointer
- * @version: device firmware version
- * @id: device ID
  *
  * Must be called during probe
  */
-static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
-				    u16 id)
+static int goodix_request_input_dev(struct goodix_ts_data *ts)
 {
 	int error;
 
@@ -351,8 +609,8 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	ts->input_dev->phys = "input/ts";
 	ts->input_dev->id.bustype = BUS_I2C;
 	ts->input_dev->id.vendor = 0x0416;
-	ts->input_dev->id.product = id;
-	ts->input_dev->id.version = version;
+	ts->input_dev->id.product = ts->id;
+	ts->input_dev->id.version = ts->version;
 
 	error = input_register_device(ts->input_dev);
 	if (error) {
@@ -364,13 +622,75 @@ static int goodix_request_input_dev(struct goodix_ts_data *ts, u16 version,
 	return 0;
 }
 
+/**
+ * goodix_configure_dev - Finish device initialization
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * Must be called from probe to finish initialization of the device.
+ * Contains the common initialization code for both devices that
+ * declare gpio pins and devices that do not. It is either called
+ * directly from probe or from request_firmware_wait callback.
+ */
+static int goodix_configure_dev(struct goodix_ts_data *ts)
+{
+	int error;
+
+	ts->swapped_x_y = device_property_read_bool(&ts->client->dev,
+						    "touchscreen-swapped-x-y");
+	ts->inverted_x = device_property_read_bool(&ts->client->dev,
+						   "touchscreen-inverted-x");
+	ts->inverted_y = device_property_read_bool(&ts->client->dev,
+						   "touchscreen-inverted-y");
+
+	goodix_read_config(ts);
+
+	error = goodix_request_input_dev(ts);
+	if (error)
+		return error;
+
+	ts->irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
+	error = goodix_request_irq(ts);
+	if (error) {
+		dev_err(&ts->client->dev, "request IRQ failed: %d\n", error);
+		return error;
+	}
+
+	return 0;
+}
+
+/**
+ * goodix_config_cb - Callback to finish device init
+ *
+ * @ts: our goodix_ts_data pointer
+ *
+ * request_firmware_wait callback that finishes
+ * initialization of the device.
+ */
+static void goodix_config_cb(const struct firmware *cfg, void *ctx)
+{
+	struct goodix_ts_data *ts = ctx;
+	int error;
+
+	if (cfg) {
+		/* send device configuration to the firmware */
+		error = goodix_send_cfg(ts, cfg);
+		if (error)
+			goto err_release_cfg;
+	}
+
+	goodix_configure_dev(ts);
+
+err_release_cfg:
+	release_firmware(cfg);
+	complete_all(&ts->firmware_loading_complete);
+}
+
 static int goodix_ts_probe(struct i2c_client *client,
 			   const struct i2c_device_id *id)
 {
 	struct goodix_ts_data *ts;
-	unsigned long irq_flags;
 	int error;
-	u16 version_info, id_info;
 
 	dev_dbg(&client->dev, "I2C Address: 0x%02x\n", client->addr);
 
@@ -385,6 +705,20 @@ static int goodix_ts_probe(struct i2c_client *client,
 
 	ts->client = client;
 	i2c_set_clientdata(client, ts);
+	init_completion(&ts->firmware_loading_complete);
+
+	error = goodix_get_gpio_config(ts);
+	if (error)
+		return error;
+
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* reset the controller */
+		error = goodix_reset(ts);
+		if (error) {
+			dev_err(&client->dev, "Controller reset failed.\n");
+			return error;
+		}
+	}
 
 	error = goodix_i2c_test(client);
 	if (error) {
@@ -392,30 +726,125 @@ static int goodix_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
-	error = goodix_read_version(client, &version_info, &id_info);
+	error = goodix_read_version(ts);
 	if (error) {
 		dev_err(&client->dev, "Read version failed.\n");
 		return error;
 	}
 
-	goodix_read_config(ts);
+	ts->cfg_len = goodix_get_cfg_len(ts->id);
+
+	if (ts->gpiod_int && ts->gpiod_rst) {
+		/* update device config */
+		ts->cfg_name = devm_kasprintf(&client->dev, GFP_KERNEL,
+					      "goodix_%d_cfg.bin", ts->id);
+		if (!ts->cfg_name)
+			return -ENOMEM;
+
+		error = request_firmware_nowait(THIS_MODULE, true, ts->cfg_name,
+						&client->dev, GFP_KERNEL, ts,
+						goodix_config_cb);
+		if (error) {
+			dev_err(&client->dev,
+				"Failed to invoke firmware loader: %d\n",
+				error);
+			return error;
+		}
 
-	error = goodix_request_input_dev(ts, version_info, id_info);
+		return 0;
+	} else {
+		error = goodix_configure_dev(ts);
 		if (error)
 			return error;
+	}
 
-	irq_flags = goodix_irq_flags[ts->int_trigger_type] | IRQF_ONESHOT;
-	error = devm_request_threaded_irq(&ts->client->dev, client->irq,
-					  NULL, goodix_ts_irq_handler,
-					  irq_flags, client->name, ts);
+	return 0;
+}
+
+static int goodix_ts_remove(struct i2c_client *client)
+{
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+
+	if (ts->gpiod_int && ts->gpiod_rst)
+		wait_for_completion(&ts->firmware_loading_complete);
+
+	return 0;
+}
+
+static int __maybe_unused goodix_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	/* We need gpio pins to suspend/resume */
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	wait_for_completion(&ts->firmware_loading_complete);
+
+	/* Free IRQ as IRQ pin is used as output in the suspend sequence */
+	goodix_free_irq(ts);
+
+	/* Output LOW on the INT pin for 5 ms */
+	error = gpiod_direction_output(ts->gpiod_int, 0);
 	if (error) {
-		dev_err(&client->dev, "request IRQ failed: %d\n", error);
+		goodix_request_irq(ts);
 		return error;
 	}
 
+	usleep_range(5000, 6000);
+
+	error = goodix_i2c_write_u8(ts->client, GOODIX_REG_COMMAND,
+				    GOODIX_CMD_SCREEN_OFF);
+	if (error) {
+		dev_err(&ts->client->dev, "Screen off command failed\n");
+		gpiod_direction_input(ts->gpiod_int);
+		goodix_request_irq(ts);
+		return -EAGAIN;
+	}
+
+	/*
+	 * The datasheet specifies that the interval between sending screen-off
+	 * command and wake-up should be longer than 58 ms. To avoid waking up
+	 * sooner, delay 58ms here.
+	 */
+	msleep(58);
 	return 0;
 }
 
+static int __maybe_unused goodix_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct goodix_ts_data *ts = i2c_get_clientdata(client);
+	int error;
+
+	if (!ts->gpiod_int || !ts->gpiod_rst)
+		return 0;
+
+	/*
+	 * Exit sleep mode by outputting HIGH level to INT pin
+	 * for 2ms~5ms.
+	 */
+	error = gpiod_direction_output(ts->gpiod_int, 1);
+	if (error)
+		return error;
+
+	usleep_range(2000, 5000);
+
+	error = goodix_int_sync(ts);
+	if (error)
+		return error;
+
+	error = goodix_request_irq(ts);
+	if (error)
+		return error;
+
+	return 0;
+}
+
+static SIMPLE_DEV_PM_OPS(goodix_pm_ops, goodix_suspend, goodix_resume);
+
 static const struct i2c_device_id goodix_ts_id[] = {
 	{ "GDIX1001:00", 0 },
 	{ }
@@ -446,11 +875,13 @@ MODULE_DEVICE_TABLE(of, goodix_of_match);
 
 static struct i2c_driver goodix_ts_driver = {
 	.probe = goodix_ts_probe,
+	.remove = goodix_ts_remove,
 	.id_table = goodix_ts_id,
 	.driver = {
 		.name = "Goodix-TS",
 		.acpi_match_table = ACPI_PTR(goodix_acpi_match),
 		.of_match_table = of_match_ptr(goodix_of_match),
+		.pm = &goodix_pm_ops,
 	},
 };
 module_i2c_driver(goodix_ts_driver);

drivers/input/touchscreen/pcap_ts.c

@@ -87,7 +87,7 @@ static void pcap_ts_read_xy(void *data, u16 res[2])
 
 static void pcap_ts_work(struct work_struct *work)
 {
-	struct delayed_work *dw = container_of(work, struct delayed_work, work);
+	struct delayed_work *dw = to_delayed_work(work);
 	struct pcap_ts *pcap_ts = container_of(dw, struct pcap_ts, work);
 	u8 ch[2];
 

drivers/input/touchscreen/pixcir_i2c_ts.c

@@ -38,6 +38,8 @@ struct pixcir_i2c_ts_data {
 	struct input_dev *input;
 	struct gpio_desc *gpio_attb;
 	struct gpio_desc *gpio_reset;
+	struct gpio_desc *gpio_enable;
+	struct gpio_desc *gpio_wake;
 	const struct pixcir_i2c_chip_data *chip;
 	int max_fingers;	/* Max fingers supported in this instance */
 	bool running;
@@ -208,6 +210,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 	struct device *dev = &ts->client->dev;
 	int ret;
 
+	if (mode == PIXCIR_POWER_ACTIVE || mode == PIXCIR_POWER_IDLE) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 1);
+	}
+
 	ret = i2c_smbus_read_byte_data(ts->client, PIXCIR_REG_POWER_MODE);
 	if (ret < 0) {
 		dev_err(dev, "%s: can't read reg 0x%x : %d\n",
@@ -228,6 +235,11 @@ static int pixcir_set_power_mode(struct pixcir_i2c_ts_data *ts,
 		return ret;
 	}
 
+	if (mode == PIXCIR_POWER_HALT) {
+		if (ts->gpio_wake)
+			gpiod_set_value_cansleep(ts->gpio_wake, 0);
+	}
+
 	return 0;
 }
 
@@ -302,6 +314,11 @@ static int pixcir_start(struct pixcir_i2c_ts_data *ts)
 	struct device *dev = &ts->client->dev;
 	int error;
 
+	if (ts->gpio_enable) {
+		gpiod_set_value_cansleep(ts->gpio_enable, 1);
+		msleep(100);
+	}
+
 	/* LEVEL_TOUCH interrupt with active low polarity */
 	error = pixcir_set_int_mode(ts, PIXCIR_INT_LEVEL_TOUCH, 0);
 	if (error) {
@@ -343,6 +360,9 @@ static int pixcir_stop(struct pixcir_i2c_ts_data *ts)
 	/* Wait till running ISR is complete */
 	synchronize_irq(ts->client->irq);
 
+	if (ts->gpio_enable)
+		gpiod_set_value_cansleep(ts->gpio_enable, 0);
+
 	return 0;
 }
 
@@ -534,6 +554,27 @@ static int pixcir_i2c_ts_probe(struct i2c_client *client,
 		return error;
 	}
 
+	tsdata->gpio_wake = devm_gpiod_get_optional(dev, "wake",
+						    GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_wake)) {
+		error = PTR_ERR(tsdata->gpio_wake);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get wake gpio: %d\n", error);
+		return error;
+	}
+
+	tsdata->gpio_enable = devm_gpiod_get_optional(dev, "enable",
+						      GPIOD_OUT_HIGH);
+	if (IS_ERR(tsdata->gpio_enable)) {
+		error = PTR_ERR(tsdata->gpio_enable);
+		if (error != -EPROBE_DEFER)
+			dev_err(dev, "Failed to get enable gpio: %d\n", error);
+		return error;
+	}
+
+	if (tsdata->gpio_enable)
+		msleep(100);
+
 	error = devm_request_threaded_irq(dev, client->irq, NULL, pixcir_ts_isr,
 					  IRQF_TRIGGER_FALLING | IRQF_ONESHOT,
 					  client->name, tsdata);

drivers/input/touchscreen/rohm_bu21023.c

@@ -725,7 +725,7 @@ static int rohm_ts_load_firmware(struct i2c_client *client,
 			break;
 
 		error = -EIO;
-	} while (++retry >= FIRMWARE_RETRY_MAX);
+	} while (++retry <= FIRMWARE_RETRY_MAX);
 
 out:
 	error2 = i2c_smbus_write_byte_data(client, INT_MASK, INT_ALL);

drivers/input/touchscreen/ti_am335x_tsc.c

@@ -273,8 +273,6 @@ static irqreturn_t titsc_irq(int irq, void *dev)
 	status = titsc_readl(ts_dev, REG_RAWIRQSTATUS);
 	if (status & IRQENB_HW_PEN) {
 		ts_dev->pen_down = true;
-		titsc_writel(ts_dev, REG_IRQWAKEUP, 0x00);
-		titsc_writel(ts_dev, REG_IRQCLR, IRQENB_HW_PEN);
 		irqclr |= IRQENB_HW_PEN;
 	}
 

drivers/input/touchscreen/ts4800-ts.c

+/*
+ * Touchscreen driver for the TS-4800 board
+ *
+ * Copyright (c) 2015 - Savoir-faire Linux
+ *
+ * This file is licensed under the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+ */
+
+#include <linux/bitops.h>
+#include <linux/input.h>
+#include <linux/input-polldev.h>
+#include <linux/io.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* polling interval in ms */
+#define POLL_INTERVAL		3
+
+#define DEBOUNCE_COUNT		1
+
+/* sensor values are 12-bit wide */
+#define MAX_12BIT		((1 << 12) - 1)
+
+#define PENDOWN_MASK		0x1
+
+#define X_OFFSET		0x0
+#define Y_OFFSET		0x2
+
+struct ts4800_ts {
+	struct input_polled_dev *poll_dev;
+	struct device           *dev;
+	char                    phys[32];
+
+	void __iomem            *base;
+	struct regmap           *regmap;
+	unsigned int            reg;
+	unsigned int            bit;
+
+	bool                    pendown;
+	int                     debounce;
+};
+
+static void ts4800_ts_open(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ts->pendown = false;
+	ts->debounce = DEBOUNCE_COUNT;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, ts->bit);
+	if (ret)
+		dev_warn(ts->dev, "Failed to enable touchscreen\n");
+}
+
+static void ts4800_ts_close(struct input_polled_dev *dev)
+{
+	struct ts4800_ts *ts = dev->private;
+	int ret;
+
+	ret = regmap_update_bits(ts->regmap, ts->reg, ts->bit, 0);
+	if (ret)
+		dev_warn(ts->dev, "Failed to disable touchscreen\n");
+
+}
+
+static void ts4800_ts_poll(struct input_polled_dev *dev)
+{
+	struct input_dev *input_dev = dev->input;
+	struct ts4800_ts *ts = dev->private;
+	u16 last_x = readw(ts->base + X_OFFSET);
+	u16 last_y = readw(ts->base + Y_OFFSET);
+	bool pendown = last_x & PENDOWN_MASK;
+
+	if (pendown) {
+		if (ts->debounce) {
+			ts->debounce--;
+			return;
+		}
+
+		if (!ts->pendown) {
+			input_report_key(input_dev, BTN_TOUCH, 1);
+			ts->pendown = true;
+		}
+
+		last_x = ((~last_x) >> 4) & MAX_12BIT;
+		last_y = ((~last_y) >> 4) & MAX_12BIT;
+
+		input_report_abs(input_dev, ABS_X, last_x);
+		input_report_abs(input_dev, ABS_Y, last_y);
+		input_sync(input_dev);
+	} else if (ts->pendown) {
+		ts->pendown = false;
+		ts->debounce = DEBOUNCE_COUNT;
+		input_report_key(input_dev, BTN_TOUCH, 0);
+		input_sync(input_dev);
+	}
+}
+
+static int ts4800_parse_dt(struct platform_device *pdev,
+			   struct ts4800_ts *ts)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct device_node *syscon_np;
+	u32 reg, bit;
+	int error;
+
+	syscon_np = of_parse_phandle(np, "syscon", 0);
+	if (!syscon_np) {
+		dev_err(dev, "no syscon property\n");
+		return -ENODEV;
+	}
+
+	error = of_property_read_u32_index(np, "syscon", 1, &reg);
+	if (error < 0) {
+		dev_err(dev, "no offset in syscon\n");
+		return error;
+	}
+
+	ts->reg = reg;
+
+	error = of_property_read_u32_index(np, "syscon", 2, &bit);
+	if (error < 0) {
+		dev_err(dev, "no bit in syscon\n");
+		return error;
+	}
+
+	ts->bit = BIT(bit);
+
+	ts->regmap = syscon_node_to_regmap(syscon_np);
+	if (IS_ERR(ts->regmap)) {
+		dev_err(dev, "cannot get parent's regmap\n");
+		return PTR_ERR(ts->regmap);
+	}
+
+	return 0;
+}
+
+static int ts4800_ts_probe(struct platform_device *pdev)
+{
+	struct input_polled_dev *poll_dev;
+	struct ts4800_ts *ts;
+	struct resource *res;
+	int error;
+
+	ts = devm_kzalloc(&pdev->dev, sizeof(*ts), GFP_KERNEL);
+	if (!ts)
+		return -ENOMEM;
+
+	error = ts4800_parse_dt(pdev, ts);
+	if (error)
+		return error;
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	ts->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(ts->base))
+		return PTR_ERR(ts->base);
+
+	poll_dev = devm_input_allocate_polled_device(&pdev->dev);
+	if (!poll_dev)
+		return -ENOMEM;
+
+	snprintf(ts->phys, sizeof(ts->phys), "%s/input0", dev_name(&pdev->dev));
+	ts->poll_dev = poll_dev;
+	ts->dev = &pdev->dev;
+
+	poll_dev->private = ts;
+	poll_dev->poll_interval = POLL_INTERVAL;
+	poll_dev->open = ts4800_ts_open;
+	poll_dev->close = ts4800_ts_close;
+	poll_dev->poll = ts4800_ts_poll;
+
+	poll_dev->input->name = "TS-4800 Touchscreen";
+	poll_dev->input->phys = ts->phys;
+
+	input_set_capability(poll_dev->input, EV_KEY, BTN_TOUCH);
+	input_set_abs_params(poll_dev->input, ABS_X, 0, MAX_12BIT, 0, 0);
+	input_set_abs_params(poll_dev->input, ABS_Y, 0, MAX_12BIT, 0, 0);
+
+	error = input_register_polled_device(poll_dev);
+	if (error) {
+		dev_err(&pdev->dev,
+			"Unabled to register polled input device (%d)\n",
+			error);
+		return error;
+	}
+
+	return 0;
+}
+
+static const struct of_device_id ts4800_ts_of_match[] = {
+	{ .compatible = "technologic,ts4800-ts", },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, ts4800_ts_of_match);
+
+static struct platform_driver ts4800_ts_driver = {
+	.driver = {
+		.name = "ts4800-ts",
+		.of_match_table = ts4800_ts_of_match,
+	},
+	.probe = ts4800_ts_probe,
+};
+module_platform_driver(ts4800_ts_driver);
+
+MODULE_AUTHOR("Damien Riegel <damien.riegel@savoirfairelinux.com>");
+MODULE_DESCRIPTION("TS-4800 Touchscreen Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_ALIAS("platform:ts4800_ts");

drivers/input/touchscreen/wacom_w8001.c

@@ -80,7 +80,8 @@ struct w8001_touch_query {
  */
 
 struct w8001 {
-	struct input_dev *dev;
+	struct input_dev *pen_dev;
+	struct input_dev *touch_dev;
 	struct serio *serio;
 	struct completion cmd_done;
 	int id;
@@ -95,7 +96,10 @@ struct w8001 {
 	u16 max_touch_y;
 	u16 max_pen_x;
 	u16 max_pen_y;
-	char name[64];
+	char pen_name[64];
+	char touch_name[64];
+	int open_count;
+	struct mutex mutex;
 };
 
 static void parse_pen_data(u8 *data, struct w8001_coord *coord)
@@ -141,7 +145,7 @@ static void scale_touch_coordinates(struct w8001 *w8001,
 
 static void parse_multi_touch(struct w8001 *w8001)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->touch_dev;
 	unsigned char *data = w8001->data;
 	unsigned int x, y;
 	int i;
@@ -151,7 +155,6 @@ static void parse_multi_touch(struct w8001 *w8001)
 		bool touch = data[0] & (1 << i);
 
 		input_mt_slot(dev, i);
-		input_mt_report_slot_state(dev, MT_TOOL_FINGER, touch);
 		if (touch) {
 			x = (data[6 * i + 1] << 7) | data[6 * i + 2];
 			y = (data[6 * i + 3] << 7) | data[6 * i + 4];
@@ -207,7 +210,7 @@ static void parse_touchquery(u8 *data, struct w8001_touch_query *query)
 
 static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->pen_dev;
 
 	/*
 	 * We have 1 bit for proximity (rdy) and 3 bits for tip, side,
@@ -233,11 +236,6 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 		break;
 
 	case BTN_TOOL_FINGER:
-		input_report_key(dev, BTN_TOUCH, 0);
-		input_report_key(dev, BTN_TOOL_FINGER, 0);
-		input_sync(dev);
-		/* fall through */
-
 	case KEY_RESERVED:
 		w8001->type = coord->f2 ? BTN_TOOL_RUBBER : BTN_TOOL_PEN;
 		break;
@@ -261,7 +259,7 @@ static void report_pen_events(struct w8001 *w8001, struct w8001_coord *coord)
 
 static void report_single_touch(struct w8001 *w8001, struct w8001_coord *coord)
 {
-	struct input_dev *dev = w8001->dev;
+	struct input_dev *dev = w8001->touch_dev;
 	unsigned int x = coord->x;
 	unsigned int y = coord->y;
 
@@ -271,7 +269,6 @@ static void report_single_touch(struct w8001 *w8001, struct w8001_coord *coord)
 	input_report_abs(dev, ABS_X, x);
 	input_report_abs(dev, ABS_Y, y);
 	input_report_key(dev, BTN_TOUCH, coord->tsw);
-	input_report_key(dev, BTN_TOOL_FINGER, coord->tsw);
 
 	input_sync(dev);
 
@@ -369,22 +366,36 @@ static int w8001_command(struct w8001 *w8001, unsigned char command,
 static int w8001_open(struct input_dev *dev)
 {
 	struct w8001 *w8001 = input_get_drvdata(dev);
+	int err;
 
-	return w8001_command(w8001, W8001_CMD_START, false);
+	err = mutex_lock_interruptible(&w8001->mutex);
+	if (err)
+		return err;
+
+	if (w8001->open_count++ == 0) {
+		err = w8001_command(w8001, W8001_CMD_START, false);
+		if (err)
+			w8001->open_count--;
+	}
+
+	mutex_unlock(&w8001->mutex);
+	return err;
 }
 
 static void w8001_close(struct input_dev *dev)
 {
 	struct w8001 *w8001 = input_get_drvdata(dev);
 
+	mutex_lock(&w8001->mutex);
+
+	if (--w8001->open_count == 0)
 		w8001_command(w8001, W8001_CMD_STOP, false);
+
+	mutex_unlock(&w8001->mutex);
 }
 
-static int w8001_setup(struct w8001 *w8001)
+static int w8001_detect(struct w8001 *w8001)
 {
-	struct input_dev *dev = w8001->dev;
-	struct w8001_coord coord;
-	struct w8001_touch_query touch;
 	int error;
 
 	error = w8001_command(w8001, W8001_CMD_STOP, false);
@@ -393,19 +404,29 @@ static int w8001_setup(struct w8001 *w8001)
 
 	msleep(250);	/* wait 250ms before querying the device */
 
-	dev->evbit[0] = BIT_MASK(EV_KEY) | BIT_MASK(EV_ABS);
-	strlcat(w8001->name, "Wacom Serial", sizeof(w8001->name));
+	return 0;
+}
 
-	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
+static int w8001_setup_pen(struct w8001 *w8001, char *basename,
+			   size_t basename_sz)
+{
+	struct input_dev *dev = w8001->pen_dev;
+	struct w8001_coord coord;
+	int error;
 
 	/* penabled? */
 	error = w8001_command(w8001, W8001_CMD_QUERY, true);
-	if (!error) {
+	if (error)
+		return error;
+
+	__set_bit(EV_KEY, dev->evbit);
+	__set_bit(EV_ABS, dev->evbit);
 	__set_bit(BTN_TOUCH, dev->keybit);
 	__set_bit(BTN_TOOL_PEN, dev->keybit);
 	__set_bit(BTN_TOOL_RUBBER, dev->keybit);
 	__set_bit(BTN_STYLUS, dev->keybit);
 	__set_bit(BTN_STYLUS2, dev->keybit);
+	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
 
 	parse_pen_data(w8001->response, &coord);
 	w8001->max_pen_x = coord.x;
@@ -420,20 +441,36 @@ static int w8001_setup(struct w8001 *w8001)
 		input_set_abs_params(dev, ABS_TILT_X, 0, coord.tilt_x, 0, 0);
 		input_set_abs_params(dev, ABS_TILT_Y, 0, coord.tilt_y, 0, 0);
 	}
+
 	w8001->id = 0x90;
-		strlcat(w8001->name, " Penabled", sizeof(w8001->name));
-	}
+	strlcat(basename, " Penabled", basename_sz);
+
+	return 0;
+}
+
+static int w8001_setup_touch(struct w8001 *w8001, char *basename,
+			     size_t basename_sz)
+{
+	struct input_dev *dev = w8001->touch_dev;
+	struct w8001_touch_query touch;
+	int error;
+
 
 	/* Touch enabled? */
 	error = w8001_command(w8001, W8001_CMD_TOUCHQUERY, true);
-
+	if (error)
+		return error;
 	/*
 	 * Some non-touch devices may reply to the touch query. But their
 	 * second byte is empty, which indicates touch is not supported.
 	 */
-	if (!error && w8001->response[1]) {
+	if (!w8001->response[1])
+		return -ENXIO;
+
+	__set_bit(EV_KEY, dev->evbit);
+	__set_bit(EV_ABS, dev->evbit);
 	__set_bit(BTN_TOUCH, dev->keybit);
-		__set_bit(BTN_TOOL_FINGER, dev->keybit);
+	__set_bit(INPUT_PROP_DIRECT, dev->propbit);
 
 	parse_touchquery(w8001->response, &touch);
 	w8001->max_touch_x = touch.x;
@@ -456,42 +493,56 @@ static int w8001_setup(struct w8001 *w8001)
 	case 2:
 		w8001->pktlen = W8001_PKTLEN_TOUCH93;
 		w8001->id = 0x93;
-			strlcat(w8001->name, " 1FG", sizeof(w8001->name));
+		strlcat(basename, " 1FG", basename_sz);
 		break;
 
 	case 1:
 	case 3:
 	case 4:
 		w8001->pktlen = W8001_PKTLEN_TOUCH9A;
-			strlcat(w8001->name, " 1FG", sizeof(w8001->name));
+		strlcat(basename, " 1FG", basename_sz);
 		w8001->id = 0x9a;
 		break;
 
 	case 5:
 		w8001->pktlen = W8001_PKTLEN_TOUCH2FG;
 
+		__set_bit(BTN_TOOL_DOUBLETAP, dev->keybit);
 		input_mt_init_slots(dev, 2, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_X,
 					0, touch.x, 0, 0);
 		input_set_abs_params(dev, ABS_MT_POSITION_Y,
 					0, touch.y, 0, 0);
-			input_set_abs_params(dev, ABS_MT_TOOL_TYPE,
-						0, MT_TOOL_MAX, 0, 0);
 
-			strlcat(w8001->name, " 2FG", sizeof(w8001->name));
+		strlcat(basename, " 2FG", basename_sz);
 		if (w8001->max_pen_x && w8001->max_pen_y)
 			w8001->id = 0xE3;
 		else
 			w8001->id = 0xE2;
 		break;
 	}
-	}
 
-	strlcat(w8001->name, " Touchscreen", sizeof(w8001->name));
+	strlcat(basename, " Touchscreen", basename_sz);
 
 	return 0;
 }
 
+static void w8001_set_devdata(struct input_dev *dev, struct w8001 *w8001,
+			      struct serio *serio)
+{
+	dev->phys = w8001->phys;
+	dev->id.bustype = BUS_RS232;
+	dev->id.product = w8001->id;
+	dev->id.vendor = 0x056a;
+	dev->id.version = 0x0100;
+	dev->open = w8001_open;
+	dev->close = w8001_close;
+
+	dev->dev.parent = &serio->dev;
+
+	input_set_drvdata(dev, w8001);
+}
+
 /*
  * w8001_disconnect() is the opposite of w8001_connect()
  */
@@ -502,7 +553,10 @@ static void w8001_disconnect(struct serio *serio)
 
 	serio_close(serio);
 
-	input_unregister_device(w8001->dev);
+	if (w8001->pen_dev)
+		input_unregister_device(w8001->pen_dev);
+	if (w8001->touch_dev)
+		input_unregister_device(w8001->touch_dev);
 	kfree(w8001);
 
 	serio_set_drvdata(serio, NULL);
@@ -517,18 +571,23 @@ static void w8001_disconnect(struct serio *serio)
 static int w8001_connect(struct serio *serio, struct serio_driver *drv)
 {
 	struct w8001 *w8001;
-	struct input_dev *input_dev;
-	int err;
+	struct input_dev *input_dev_pen;
+	struct input_dev *input_dev_touch;
+	char basename[64];
+	int err, err_pen, err_touch;
 
 	w8001 = kzalloc(sizeof(struct w8001), GFP_KERNEL);
-	input_dev = input_allocate_device();
-	if (!w8001 || !input_dev) {
+	input_dev_pen = input_allocate_device();
+	input_dev_touch = input_allocate_device();
+	if (!w8001 || !input_dev_pen || !input_dev_touch) {
 		err = -ENOMEM;
 		goto fail1;
 	}
 
 	w8001->serio = serio;
-	w8001->dev = input_dev;
+	w8001->pen_dev = input_dev_pen;
+	w8001->touch_dev = input_dev_touch;
+	mutex_init(&w8001->mutex);
 	init_completion(&w8001->cmd_done);
 	snprintf(w8001->phys, sizeof(w8001->phys), "%s/input0", serio->phys);
 
@@ -537,35 +596,67 @@ static int w8001_connect(struct serio *serio, struct serio_driver *drv)
 	if (err)
 		goto fail2;
 
-	err = w8001_setup(w8001);
+	err = w8001_detect(w8001);
 	if (err)
 		goto fail3;
 
-	input_dev->name = w8001->name;
-	input_dev->phys = w8001->phys;
-	input_dev->id.product = w8001->id;
-	input_dev->id.bustype = BUS_RS232;
-	input_dev->id.vendor = 0x056a;
-	input_dev->id.version = 0x0100;
-	input_dev->dev.parent = &serio->dev;
+	/* For backwards-compatibility we compose the basename based on
+	 * capabilities and then just append the tool type
+	 */
+	strlcpy(basename, "Wacom Serial", sizeof(basename));
+
+	err_pen = w8001_setup_pen(w8001, basename, sizeof(basename));
+	err_touch = w8001_setup_touch(w8001, basename, sizeof(basename));
+	if (err_pen && err_touch) {
+		err = -ENXIO;
+		goto fail3;
+	}
 
-	input_dev->open = w8001_open;
-	input_dev->close = w8001_close;
+	if (!err_pen) {
+		strlcpy(w8001->pen_name, basename, sizeof(w8001->pen_name));
+		strlcat(w8001->pen_name, " Pen", sizeof(w8001->pen_name));
+		input_dev_pen->name = w8001->pen_name;
 
-	input_set_drvdata(input_dev, w8001);
+		w8001_set_devdata(input_dev_pen, w8001, serio);
 
-	err = input_register_device(w8001->dev);
+		err = input_register_device(w8001->pen_dev);
 		if (err)
 			goto fail3;
+	} else {
+		input_free_device(input_dev_pen);
+		input_dev_pen = NULL;
+		w8001->pen_dev = NULL;
+	}
+
+	if (!err_touch) {
+		strlcpy(w8001->touch_name, basename, sizeof(w8001->touch_name));
+		strlcat(w8001->touch_name, " Finger",
+			sizeof(w8001->touch_name));
+		input_dev_touch->name = w8001->touch_name;
+
+		w8001_set_devdata(input_dev_touch, w8001, serio);
+
+		err = input_register_device(w8001->touch_dev);
+		if (err)
+			goto fail4;
+	} else {
+		input_free_device(input_dev_touch);
+		input_dev_touch = NULL;
+		w8001->touch_dev = NULL;
+	}
 
 	return 0;
 
+fail4:
+	if (w8001->pen_dev)
+		input_unregister_device(w8001->pen_dev);
 fail3:
 	serio_close(serio);
 fail2:
 	serio_set_drvdata(serio, NULL);
 fail1:
-	input_free_device(input_dev);
+	input_free_device(input_dev_pen);
+	input_free_device(input_dev_touch);
 	kfree(w8001);
 	return err;
 }

include/linux/uinput.h

@@ -20,6 +20,11 @@
  * Author: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
  *
  * Changes/Revisions:
+ *	0.5	08/13/2015 (David Herrmann <dh.herrmann@gmail.com> &
+ *			    Benjamin Tissoires <benjamin.tissoires@redhat.com>)
+ *		- add UI_DEV_SETUP ioctl
+ *		- add UI_ABS_SETUP ioctl
+ *		- add UI_GET_VERSION ioctl
  *	0.4	01/09/2014 (Benjamin Tissoires <benjamin.tissoires@redhat.com>)
  *		- add UI_GET_SYSNAME ioctl
  *	0.3	24/05/2006 (Anssi Hannula <anssi.hannulagmail.com>)

include/uapi/linux/serio.h

@@ -77,5 +77,6 @@
 #define SERIO_PS2MULT	0x3c
 #define SERIO_TSC40	0x3d
 #define SERIO_WACOM_IV	0x3e
+#define SERIO_EGALAX	0x3f
 
 #endif /* _UAPI_SERIO_H */

include/uapi/linux/uinput.h

@@ -20,6 +20,11 @@
  * Author: Aristeu Sergio Rozanski Filho <aris@cathedrallabs.org>
  *
  * Changes/Revisions:
+ *	0.5	08/13/2015 (David Herrmann <dh.herrmann@gmail.com> &
+ *			    Benjamin Tissoires <benjamin.tissoires@redhat.com>)
+ *		- add UI_DEV_SETUP ioctl
+ *		- add UI_ABS_SETUP ioctl
+ *		- add UI_GET_VERSION ioctl
  *	0.4	01/09/2014 (Benjamin Tissoires <benjamin.tissoires@redhat.com>)
  *		- add UI_GET_SYSNAME ioctl
  *	0.3	24/05/2006 (Anssi Hannula <anssi.hannulagmail.com>)
@@ -37,8 +42,8 @@
 #include <linux/types.h>
 #include <linux/input.h>
 
-#define UINPUT_VERSION		4
-
+#define UINPUT_VERSION		5
+#define UINPUT_MAX_NAME_SIZE	80
 
 struct uinput_ff_upload {
 	__u32			request_id;
@@ -58,6 +63,76 @@ struct uinput_ff_erase {
 #define UI_DEV_CREATE		_IO(UINPUT_IOCTL_BASE, 1)
 #define UI_DEV_DESTROY		_IO(UINPUT_IOCTL_BASE, 2)
 
+struct uinput_setup {
+	struct input_id id;
+	char name[UINPUT_MAX_NAME_SIZE];
+	__u32 ff_effects_max;
+};
+
+/**
+ * UI_DEV_SETUP - Set device parameters for setup
+ *
+ * This ioctl sets parameters for the input device to be created.  It
+ * supersedes the old "struct uinput_user_dev" method, which wrote this data
+ * via write(). To actually set the absolute axes UI_ABS_SETUP should be
+ * used.
+ *
+ * The ioctl takes a "struct uinput_setup" object as argument. The fields of
+ * this object are as follows:
+ *              id: See the description of "struct input_id". This field is
+ *                  copied unchanged into the new device.
+ *            name: This is used unchanged as name for the new device.
+ *  ff_effects_max: This limits the maximum numbers of force-feedback effects.
+ *                  See below for a description of FF with uinput.
+ *
+ * This ioctl can be called multiple times and will overwrite previous values.
+ * If this ioctl fails with -EINVAL, it is recommended to use the old
+ * "uinput_user_dev" method via write() as a fallback, in case you run on an
+ * old kernel that does not support this ioctl.
+ *
+ * This ioctl may fail with -EINVAL if it is not supported or if you passed
+ * incorrect values, -ENOMEM if the kernel runs out of memory or -EFAULT if the
+ * passed uinput_setup object cannot be read/written.
+ * If this call fails, partial data may have already been applied to the
+ * internal device.
+ */
+#define UI_DEV_SETUP _IOW(UINPUT_IOCTL_BASE, 3, struct uinput_setup)
+
+struct uinput_abs_setup {
+	__u16  code; /* axis code */
+	/* __u16 filler; */
+	struct input_absinfo absinfo;
+};
+
+/**
+ * UI_ABS_SETUP - Set absolute axis information for the device to setup
+ *
+ * This ioctl sets one absolute axis information for the input device to be
+ * created. It supersedes the old "struct uinput_user_dev" method, which wrote
+ * part of this data and the content of UI_DEV_SETUP via write().
+ *
+ * The ioctl takes a "struct uinput_abs_setup" object as argument. The fields
+ * of this object are as follows:
+ *            code: The corresponding input code associated with this axis
+ *                  (ABS_X, ABS_Y, etc...)
+ *         absinfo: See "struct input_absinfo" for a description of this field.
+ *                  This field is copied unchanged into the kernel for the
+ *                  specified axis. If the axis is not enabled via
+ *                  UI_SET_ABSBIT, this ioctl will enable it.
+ *
+ * This ioctl can be called multiple times and will overwrite previous values.
+ * If this ioctl fails with -EINVAL, it is recommended to use the old
+ * "uinput_user_dev" method via write() as a fallback, in case you run on an
+ * old kernel that does not support this ioctl.
+ *
+ * This ioctl may fail with -EINVAL if it is not supported or if you passed
+ * incorrect values, -ENOMEM if the kernel runs out of memory or -EFAULT if the
+ * passed uinput_setup object cannot be read/written.
+ * If this call fails, partial data may have already been applied to the
+ * internal device.
+ */
+#define UI_ABS_SETUP _IOW(UINPUT_IOCTL_BASE, 4, struct uinput_abs_setup)
+
 #define UI_SET_EVBIT		_IOW(UINPUT_IOCTL_BASE, 100, int)
 #define UI_SET_KEYBIT		_IOW(UINPUT_IOCTL_BASE, 101, int)
 #define UI_SET_RELBIT		_IOW(UINPUT_IOCTL_BASE, 102, int)
@@ -144,7 +219,6 @@ struct uinput_ff_erase {
 #define UI_FF_UPLOAD		1
 #define UI_FF_ERASE		2
 
-#define UINPUT_MAX_NAME_SIZE	80
 struct uinput_user_dev {
 	char name[UINPUT_MAX_NAME_SIZE];
 	struct input_id id;