mtd: at91: atmel_nand: add Programmable Multibit ECC controller support

The Programmable Multibit ECC (PMECC) controller is a programmable binary
BCH(Bose, Chaudhuri and Hocquenghem) encoder and decoder. This controller
can be used to support both SLC and MLC NAND Flash devices. It supports to
generate ECC to correct 2, 4, 8, 12 or 24 bits of error per sector of data.

To use PMECC in this driver, the user needs to set the address and size of
PMECC, PMECC error location controllers and ROM. And also needs to pass the
correction capability, the sector size and ROM lookup table offsets via dt.

This driver has been tested on AT91SAM9X5-EK and AT91SAM9N12-EK with JFFS2,
YAFFS2, UBIFS and mtd-utils.
Signed-off-by: Hong Xu <hong.xu@atmel.com>
Signed-off-by: Josh Wu <josh.wu@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>

drivers/mtd/nand/atmel_nand_ecc.h

@@ -3,7 +3,7 @@
  * Based on AT91SAM9260 datasheet revision B.
  *
  * Copyright (C) 2007 Andrew Victor
- * Copyright (C) 2007 Atmel Corporation.
+ * Copyright (C) 2007 - 2012 Atmel Corporation.
  *
  * This program is free software; you can redistribute it and/or modify it
  * under the terms of the GNU General Public License as published by the
@@ -36,4 +36,116 @@
 #define ATMEL_ECC_NPR		0x10			/* NParity register */
 #define		ATMEL_ECC_NPARITY	(0xffff << 0)		/* NParity */
 
+/* PMECC Register Definitions */
+#define ATMEL_PMECC_CFG			0x000	/* Configuration Register */
+#define		PMECC_CFG_BCH_ERR2		(0 << 0)
+#define		PMECC_CFG_BCH_ERR4		(1 << 0)
+#define		PMECC_CFG_BCH_ERR8		(2 << 0)
+#define		PMECC_CFG_BCH_ERR12		(3 << 0)
+#define		PMECC_CFG_BCH_ERR24		(4 << 0)
+
+#define		PMECC_CFG_SECTOR512		(0 << 4)
+#define		PMECC_CFG_SECTOR1024		(1 << 4)
+
+#define		PMECC_CFG_PAGE_1SECTOR		(0 << 8)
+#define		PMECC_CFG_PAGE_2SECTORS		(1 << 8)
+#define		PMECC_CFG_PAGE_4SECTORS		(2 << 8)
+#define		PMECC_CFG_PAGE_8SECTORS		(3 << 8)
+
+#define		PMECC_CFG_READ_OP		(0 << 12)
+#define		PMECC_CFG_WRITE_OP		(1 << 12)
+
+#define		PMECC_CFG_SPARE_ENABLE		(1 << 16)
+#define		PMECC_CFG_SPARE_DISABLE		(0 << 16)
+
+#define		PMECC_CFG_AUTO_ENABLE		(1 << 20)
+#define		PMECC_CFG_AUTO_DISABLE		(0 << 20)
+
+#define ATMEL_PMECC_SAREA		0x004	/* Spare area size */
+#define ATMEL_PMECC_SADDR		0x008	/* PMECC starting address */
+#define ATMEL_PMECC_EADDR		0x00c	/* PMECC ending address */
+#define ATMEL_PMECC_CLK			0x010	/* PMECC clock control */
+#define		PMECC_CLK_133MHZ		(2 << 0)
+
+#define ATMEL_PMECC_CTRL		0x014	/* PMECC control register */
+#define		PMECC_CTRL_RST			(1 << 0)
+#define		PMECC_CTRL_DATA			(1 << 1)
+#define		PMECC_CTRL_USER			(1 << 2)
+#define		PMECC_CTRL_ENABLE		(1 << 4)
+#define		PMECC_CTRL_DISABLE		(1 << 5)
+
+#define ATMEL_PMECC_SR			0x018	/* PMECC status register */
+#define		PMECC_SR_BUSY			(1 << 0)
+#define		PMECC_SR_ENABLE			(1 << 4)
+
+#define ATMEL_PMECC_IER			0x01c	/* PMECC interrupt enable */
+#define		PMECC_IER_ENABLE		(1 << 0)
+#define ATMEL_PMECC_IDR			0x020	/* PMECC interrupt disable */
+#define		PMECC_IER_DISABLE		(1 << 0)
+#define ATMEL_PMECC_IMR			0x024	/* PMECC interrupt mask */
+#define		PMECC_IER_MASK			(1 << 0)
+#define ATMEL_PMECC_ISR			0x028	/* PMECC interrupt status */
+#define ATMEL_PMECC_ECCx		0x040	/* PMECC ECC x */
+#define ATMEL_PMECC_REMx		0x240	/* PMECC REM x */
+
+/* PMERRLOC Register Definitions */
+#define ATMEL_PMERRLOC_ELCFG		0x000	/* Error location config */
+#define		PMERRLOC_ELCFG_SECTOR_512	(0 << 0)
+#define		PMERRLOC_ELCFG_SECTOR_1024	(1 << 0)
+#define		PMERRLOC_ELCFG_NUM_ERRORS(n)	((n) << 16)
+
+#define ATMEL_PMERRLOC_ELPRIM		0x004	/* Error location primitive */
+#define ATMEL_PMERRLOC_ELEN		0x008	/* Error location enable */
+#define ATMEL_PMERRLOC_ELDIS		0x00c	/* Error location disable */
+#define		PMERRLOC_DISABLE		(1 << 0)
+
+#define ATMEL_PMERRLOC_ELSR		0x010	/* Error location status */
+#define		PMERRLOC_ELSR_BUSY		(1 << 0)
+#define ATMEL_PMERRLOC_ELIER		0x014	/* Error location int enable */
+#define ATMEL_PMERRLOC_ELIDR		0x018	/* Error location int disable */
+#define ATMEL_PMERRLOC_ELIMR		0x01c	/* Error location int mask */
+#define ATMEL_PMERRLOC_ELISR		0x020	/* Error location int status */
+#define		PMERRLOC_ERR_NUM_MASK		(0x1f << 8)
+#define		PMERRLOC_CALC_DONE		(1 << 0)
+#define ATMEL_PMERRLOC_SIGMAx		0x028	/* Error location SIGMA x */
+#define ATMEL_PMERRLOC_ELx		0x08c	/* Error location x */
+
+/* Register access macros for PMECC */
+#define pmecc_readl_relaxed(addr, reg) \
+	readl_relaxed((addr) + ATMEL_PMECC_##reg)
+
+#define pmecc_writel(addr, reg, value) \
+	writel((value), (addr) + ATMEL_PMECC_##reg)
+
+#define pmecc_readb_ecc_relaxed(addr, sector, n) \
+	readb_relaxed((addr) + ATMEL_PMECC_ECCx + ((sector) * 0x40) + (n))
+
+#define pmecc_readl_rem_relaxed(addr, sector, n) \
+	readl_relaxed((addr) + ATMEL_PMECC_REMx + ((sector) * 0x40) + ((n) * 4))
+
+#define pmerrloc_readl_relaxed(addr, reg) \
+	readl_relaxed((addr) + ATMEL_PMERRLOC_##reg)
+
+#define pmerrloc_writel(addr, reg, value) \
+	writel((value), (addr) + ATMEL_PMERRLOC_##reg)
+
+#define pmerrloc_writel_sigma_relaxed(addr, n, value) \
+	writel_relaxed((value), (addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
+
+#define pmerrloc_readl_sigma_relaxed(addr, n) \
+	readl_relaxed((addr) + ATMEL_PMERRLOC_SIGMAx + ((n) * 4))
+
+#define pmerrloc_readl_el_relaxed(addr, n) \
+	readl_relaxed((addr) + ATMEL_PMERRLOC_ELx + ((n) * 4))
+
+/* Galois field dimension */
+#define PMECC_GF_DIMENSION_13			13
+#define PMECC_GF_DIMENSION_14			14
+
+#define PMECC_LOOKUP_TABLE_SIZE_512		0x2000
+#define PMECC_LOOKUP_TABLE_SIZE_1024		0x4000
+
+/* Time out value for reading PMECC status register */
+#define PMECC_MAX_TIMEOUT_MS			100
+
 #endif