phy: Add USB3 PHY support for Intel LGM SoC

Add support for USB PHY on Intel LGM SoC.
Signed-off-by: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20200828022312.52724-3-vadivel.muruganx.ramuthevar@linux.intel.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

drivers/phy/Kconfig

@@ -49,6 +49,16 @@ config PHY_XGENE
 	help
 	  This option enables support for APM X-Gene SoC multi-purpose PHY.
 
+config USB_LGM_PHY
+	tristate "INTEL Lightning Mountain USB PHY Driver"
+	select USB_PHY
+	select REGULATOR
+	select REGULATOR_FIXED_VOLTAGE
+	help
+	  Enable this to support Intel DWC3 PHY USB phy. This driver provides
+	  interface to interact with USB GEN-II and USB 3.x PHY that is part
+	  of the Intel network SOC.
+
 source "drivers/phy/allwinner/Kconfig"
 source "drivers/phy/amlogic/Kconfig"
 source "drivers/phy/broadcom/Kconfig"

drivers/phy/Makefile

@@ -8,6 +8,7 @@ obj-$(CONFIG_GENERIC_PHY_MIPI_DPHY)	+= phy-core-mipi-dphy.o
 obj-$(CONFIG_PHY_LPC18XX_USB_OTG)	+= phy-lpc18xx-usb-otg.o
 obj-$(CONFIG_PHY_XGENE)			+= phy-xgene.o
 obj-$(CONFIG_PHY_PISTACHIO_USB)		+= phy-pistachio-usb.o
+obj-$(CONFIG_USB_LGM_PHY)		+= phy-lgm-usb.o
 obj-y					+= allwinner/	\
 					   amlogic/	\
 					   broadcom/	\

drivers/phy/phy-lgm-usb.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Intel LGM USB PHY driver
+ *
+ * Copyright (C) 2020 Intel Corporation.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/delay.h>
+#include <linux/iopoll.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regulator/consumer.h>
+#include <linux/reset.h>
+#include <linux/usb/phy.h>
+#include <linux/workqueue.h>
+
+#define CTRL1_OFFSET		0x14
+#define SRAM_EXT_LD_DONE	BIT(25)
+#define SRAM_INIT_DONE		BIT(26)
+
+#define TCPC_OFFSET		0x1014
+#define TCPC_MUX_CTL		GENMASK(1, 0)
+#define MUX_NC			0
+#define MUX_USB			1
+#define MUX_DP			2
+#define MUX_USBDP		3
+#define TCPC_FLIPPED		BIT(2)
+#define TCPC_LOW_POWER_EN	BIT(3)
+#define TCPC_VALID		BIT(4)
+#define TCPC_CONN		\
+	(TCPC_VALID | FIELD_PREP(TCPC_MUX_CTL, MUX_USB))
+#define TCPC_DISCONN		\
+	(TCPC_VALID | FIELD_PREP(TCPC_MUX_CTL, MUX_NC) | TCPC_LOW_POWER_EN)
+
+static const char *const PHY_RESETS[] = { "phy31", "phy", };
+static const char *const CTL_RESETS[] = { "apb", "ctrl", };
+
+struct tca_apb {
+	struct reset_control *resets[ARRAY_SIZE(PHY_RESETS)];
+	struct regulator *vbus;
+	struct work_struct wk;
+	struct usb_phy phy;
+
+	bool regulator_enabled;
+	bool phy_initialized;
+	bool connected;
+};
+
+static int get_flipped(struct tca_apb *ta, bool *flipped)
+{
+	union extcon_property_value property;
+	int ret;
+
+	ret = extcon_get_property(ta->phy.edev, EXTCON_USB_HOST,
+				  EXTCON_PROP_USB_TYPEC_POLARITY, &property);
+	if (ret) {
+		dev_err(ta->phy.dev, "no polarity property from extcon\n");
+		return ret;
+	}
+
+	*flipped = property.intval;
+
+	return 0;
+}
+
+static int phy_init(struct usb_phy *phy)
+{
+	struct tca_apb *ta = container_of(phy, struct tca_apb, phy);
+	void __iomem *ctrl1 = phy->io_priv + CTRL1_OFFSET;
+	int val, ret, i;
+
+	if (ta->phy_initialized)
+		return 0;
+
+	for (i = 0; i < ARRAY_SIZE(PHY_RESETS); i++)
+		reset_control_deassert(ta->resets[i]);
+
+	ret = readl_poll_timeout(ctrl1, val, val & SRAM_INIT_DONE, 10, 10 * 1000);
+	if (ret) {
+		dev_err(ta->phy.dev, "SRAM init failed, 0x%x\n", val);
+		return ret;
+	}
+
+	writel(readl(ctrl1) | SRAM_EXT_LD_DONE, ctrl1);
+
+	ta->phy_initialized = true;
+	if (!ta->phy.edev) {
+		writel(TCPC_CONN, ta->phy.io_priv + TCPC_OFFSET);
+		return phy->set_vbus(phy, true);
+	}
+
+	schedule_work(&ta->wk);
+
+	return ret;
+}
+
+static void phy_shutdown(struct usb_phy *phy)
+{
+	struct tca_apb *ta = container_of(phy, struct tca_apb, phy);
+	int i;
+
+	if (!ta->phy_initialized)
+		return;
+
+	ta->phy_initialized = false;
+	flush_work(&ta->wk);
+	ta->phy.set_vbus(&ta->phy, false);
+
+	ta->connected = false;
+	writel(TCPC_DISCONN, ta->phy.io_priv + TCPC_OFFSET);
+
+	for (i = 0; i < ARRAY_SIZE(PHY_RESETS); i++)
+		reset_control_assert(ta->resets[i]);
+}
+
+static int phy_set_vbus(struct usb_phy *phy, int on)
+{
+	struct tca_apb *ta = container_of(phy, struct tca_apb, phy);
+	int ret;
+
+	if (!!on == ta->regulator_enabled)
+		return 0;
+
+	if (on)
+		ret = regulator_enable(ta->vbus);
+	else
+		ret = regulator_disable(ta->vbus);
+
+	if (!ret)
+		ta->regulator_enabled = on;
+
+	dev_dbg(ta->phy.dev, "set vbus: %d\n", on);
+	return ret;
+}
+
+static void tca_work(struct work_struct *work)
+{
+	struct tca_apb *ta = container_of(work, struct tca_apb, wk);
+	bool connected;
+	bool flipped = false;
+	u32 val;
+	int ret;
+
+	ret = get_flipped(ta, &flipped);
+	if (ret)
+		return;
+
+	connected = extcon_get_state(ta->phy.edev, EXTCON_USB_HOST);
+	if (connected == ta->connected)
+		return;
+
+	ta->connected = connected;
+	if (connected) {
+		val = TCPC_CONN;
+		if (flipped)
+			val |= TCPC_FLIPPED;
+		dev_dbg(ta->phy.dev, "connected%s\n", flipped ? " flipped" : "");
+	} else {
+		val = TCPC_DISCONN;
+		dev_dbg(ta->phy.dev, "disconnected\n");
+	}
+
+	writel(val, ta->phy.io_priv + TCPC_OFFSET);
+
+	ret = ta->phy.set_vbus(&ta->phy, connected);
+	if (ret)
+		dev_err(ta->phy.dev, "failed to set VBUS\n");
+}
+
+static int id_notifier(struct notifier_block *nb, unsigned long event, void *ptr)
+{
+	struct tca_apb *ta = container_of(nb, struct tca_apb, phy.id_nb);
+
+	if (ta->phy_initialized)
+		schedule_work(&ta->wk);
+
+	return NOTIFY_DONE;
+}
+
+static int vbus_notifier(struct notifier_block *nb, unsigned long evnt, void *ptr)
+{
+	return NOTIFY_DONE;
+}
+
+static int phy_probe(struct platform_device *pdev)
+{
+	struct reset_control *resets[ARRAY_SIZE(CTL_RESETS)];
+	struct device *dev = &pdev->dev;
+	struct usb_phy *phy;
+	struct tca_apb *ta;
+	int i;
+
+	ta = devm_kzalloc(dev, sizeof(*ta), GFP_KERNEL);
+	if (!ta)
+		return -ENOMEM;
+
+	platform_set_drvdata(pdev, ta);
+	INIT_WORK(&ta->wk, tca_work);
+
+	phy = &ta->phy;
+	phy->dev = dev;
+	phy->label = dev_name(dev);
+	phy->type = USB_PHY_TYPE_USB3;
+	phy->init = phy_init;
+	phy->shutdown = phy_shutdown;
+	phy->set_vbus = phy_set_vbus;
+	phy->id_nb.notifier_call = id_notifier;
+	phy->vbus_nb.notifier_call = vbus_notifier;
+
+	phy->io_priv = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(phy->io_priv))
+		return PTR_ERR(phy->io_priv);
+
+	ta->vbus = devm_regulator_get(dev, "vbus");
+	if (IS_ERR(ta->vbus))
+		return PTR_ERR(ta->vbus);
+
+	for (i = 0; i < ARRAY_SIZE(CTL_RESETS); i++) {
+		resets[i] = devm_reset_control_get_exclusive(dev, CTL_RESETS[i]);
+		if (IS_ERR(resets[i])) {
+			dev_err(dev, "%s reset not found\n", CTL_RESETS[i]);
+			return PTR_ERR(resets[i]);
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(PHY_RESETS); i++) {
+		ta->resets[i] = devm_reset_control_get_exclusive(dev, PHY_RESETS[i]);
+		if (IS_ERR(ta->resets[i])) {
+			dev_err(dev, "%s reset not found\n", PHY_RESETS[i]);
+			return PTR_ERR(ta->resets[i]);
+		}
+	}
+
+	for (i = 0; i < ARRAY_SIZE(CTL_RESETS); i++)
+		reset_control_assert(resets[i]);
+
+	for (i = 0; i < ARRAY_SIZE(PHY_RESETS); i++)
+		reset_control_assert(ta->resets[i]);
+	/*
+	 * Out-of-band reset of the controller after PHY reset will cause
+	 * controller malfunctioning, so we should use in-band controller
+	 * reset only and leave the controller de-asserted here.
+	 */
+	for (i = 0; i < ARRAY_SIZE(CTL_RESETS); i++)
+		reset_control_deassert(resets[i]);
+
+	/* Need to wait at least 20us after de-assert the controller */
+	usleep_range(20, 100);
+
+	return usb_add_phy_dev(phy);
+}
+
+static int phy_remove(struct platform_device *pdev)
+{
+	struct tca_apb *ta = platform_get_drvdata(pdev);
+
+	usb_remove_phy(&ta->phy);
+
+	return 0;
+}
+
+static const struct of_device_id intel_usb_phy_dt_ids[] = {
+	{ .compatible = "intel,lgm-usb-phy" },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, intel_usb_phy_dt_ids);
+
+static struct platform_driver lgm_phy_driver = {
+	.driver = {
+		.name = "lgm-usb-phy",
+		.of_match_table = intel_usb_phy_dt_ids,
+	},
+	.probe = phy_probe,
+	.remove = phy_remove,
+};
+
+module_platform_driver(lgm_phy_driver);
+
+MODULE_DESCRIPTION("Intel LGM USB PHY driver");
+MODULE_AUTHOR("Li Yin <yin1.li@intel.com>");
+MODULE_AUTHOR("Vadivel Murugan R <vadivel.muruganx.ramuthevar@linux.intel.com>");
+MODULE_LICENSE("GPL v2");