r8152: remove clearing bp

The xxx_clear_bp() is used to halt the firmware. It only necessary
for updating the new firmware. Besides, depend on the version of
the current firmware, it may have problem to halt the firmware
directly. Finally, halt the firmware would let the firmware code
useless, and the bugs which are fixed by the firmware would occur.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/usb/r8152.c

@@ -24,7 +24,7 @@
 #include <net/ip6_checksum.h>
 
 /* Version Information */
-#define DRIVER_VERSION "v1.06.0 (2014/03/03)"
+#define DRIVER_VERSION "v1.06.1 (2014/10/01)"
 #define DRIVER_AUTHOR "Realtek linux nic maintainers <nic_swsd@realtek.com>"
 #define DRIVER_DESC "Realtek RTL8152/RTL8153 Based USB Ethernet Adapters"
 #define MODULENAME "r8152"
@@ -2201,28 +2201,6 @@ static void rtl_phy_reset(struct r8152 *tp)
 	}
 }
 
-static void rtl_clear_bp(struct r8152 *tp)
-{
-	ocp_write_dword(tp, MCU_TYPE_PLA, PLA_BP_0, 0);
-	ocp_write_dword(tp, MCU_TYPE_PLA, PLA_BP_2, 0);
-	ocp_write_dword(tp, MCU_TYPE_PLA, PLA_BP_4, 0);
-	ocp_write_dword(tp, MCU_TYPE_PLA, PLA_BP_6, 0);
-	ocp_write_dword(tp, MCU_TYPE_USB, USB_BP_0, 0);
-	ocp_write_dword(tp, MCU_TYPE_USB, USB_BP_2, 0);
-	ocp_write_dword(tp, MCU_TYPE_USB, USB_BP_4, 0);
-	ocp_write_dword(tp, MCU_TYPE_USB, USB_BP_6, 0);
-	mdelay(3);
-	ocp_write_word(tp, MCU_TYPE_PLA, PLA_BP_BA, 0);
-	ocp_write_word(tp, MCU_TYPE_USB, USB_BP_BA, 0);
-}
-
-static void r8153_clear_bp(struct r8152 *tp)
-{
-	ocp_write_byte(tp, MCU_TYPE_PLA, PLA_BP_EN, 0);
-	ocp_write_byte(tp, MCU_TYPE_USB, USB_BP_EN, 0);
-	rtl_clear_bp(tp);
-}
-
 static void r8153_teredo_off(struct r8152 *tp)
 {
 	u32 ocp_data;
@@ -2265,8 +2243,6 @@ static void r8152b_hw_phy_cfg(struct r8152 *tp)
 		r8152_mdio_write(tp, MII_BMCR, data);
 	}
 
-	rtl_clear_bp(tp);
-
 	set_bit(PHY_RESET, &tp->flags);
 }
 
@@ -2417,8 +2393,6 @@ static void r8153_hw_phy_cfg(struct r8152 *tp)
 		r8152_mdio_write(tp, MII_BMCR, data);
 	}
 
-	r8153_clear_bp(tp);
-
 	if (tp->version == RTL_VER_03) {
 		data = ocp_reg_read(tp, OCP_EEE_CFG);
 		data &= ~CTAP_SHORT_EN;