Commit 246d7f77 authored by Florian Fainelli's avatar Florian Fainelli Committed by David S. Miller

net: dsa: add Broadcom SF2 switch driver

Add support for the Broadcom Starfigther 2 switch chip using a DSA
driver. This switch driver supports the following features:

- configuration of the external switch port interface: MII, RevMII,
  RGMII and RGMII_NO_ID are supported
- support for the per-port MIB counters
- support for link interrupts for special ports (e.g: MoCA)
- powering up/down of switch memories to conserve power when ports are
  unused

Finally, update the compatible property for the DSA core code to match
our switch top-level compatible node.
Signed-off-by: default avatarFlorian Fainelli <f.fainelli@gmail.com>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 5037d532
......@@ -36,4 +36,15 @@ config NET_DSA_MV88E6123_61_65
This enables support for the Marvell 88E6123/6161/6165
ethernet switch chips.
config NET_DSA_BCM_SF2
tristate "Broadcom Starfighter 2 Ethernet switch support"
select NET_DSA
select NET_DSA_TAG_BRCM
select FIXED_PHY if NET_DSA_BCM_SF2=y
select BCM7XXX_PHY
select MDIO_BCM_UNIMAC
---help---
This enables support for the Broadcom Starfighter 2 Ethernet
switch chips.
endmenu
......@@ -7,3 +7,4 @@ endif
ifdef CONFIG_NET_DSA_MV88E6131
mv88e6xxx_drv-y += mv88e6131.o
endif
obj-$(CONFIG_NET_DSA_BCM_SF2) += bcm_sf2.o
/*
* Broadcom Starfighter 2 DSA switch driver
*
* Copyright (C) 2014, Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#include <linux/list.h>
#include <linux/module.h>
#include <linux/netdevice.h>
#include <linux/interrupt.h>
#include <linux/platform_device.h>
#include <linux/of.h>
#include <linux/phy.h>
#include <linux/phy_fixed.h>
#include <linux/mii.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/of_address.h>
#include <net/dsa.h>
#include "bcm_sf2.h"
#include "bcm_sf2_regs.h"
/* String, offset, and register size in bytes if different from 4 bytes */
static const struct bcm_sf2_hw_stats bcm_sf2_mib[] = {
{ "TxOctets", 0x000, 8 },
{ "TxDropPkts", 0x020 },
{ "TxQPKTQ0", 0x030 },
{ "TxBroadcastPkts", 0x040 },
{ "TxMulticastPkts", 0x050 },
{ "TxUnicastPKts", 0x060 },
{ "TxCollisions", 0x070 },
{ "TxSingleCollision", 0x080 },
{ "TxMultipleCollision", 0x090 },
{ "TxDeferredCollision", 0x0a0 },
{ "TxLateCollision", 0x0b0 },
{ "TxExcessiveCollision", 0x0c0 },
{ "TxFrameInDisc", 0x0d0 },
{ "TxPausePkts", 0x0e0 },
{ "TxQPKTQ1", 0x0f0 },
{ "TxQPKTQ2", 0x100 },
{ "TxQPKTQ3", 0x110 },
{ "TxQPKTQ4", 0x120 },
{ "TxQPKTQ5", 0x130 },
{ "RxOctets", 0x140, 8 },
{ "RxUndersizePkts", 0x160 },
{ "RxPausePkts", 0x170 },
{ "RxPkts64Octets", 0x180 },
{ "RxPkts65to127Octets", 0x190 },
{ "RxPkts128to255Octets", 0x1a0 },
{ "RxPkts256to511Octets", 0x1b0 },
{ "RxPkts512to1023Octets", 0x1c0 },
{ "RxPkts1024toMaxPktsOctets", 0x1d0 },
{ "RxOversizePkts", 0x1e0 },
{ "RxJabbers", 0x1f0 },
{ "RxAlignmentErrors", 0x200 },
{ "RxFCSErrors", 0x210 },
{ "RxGoodOctets", 0x220, 8 },
{ "RxDropPkts", 0x240 },
{ "RxUnicastPkts", 0x250 },
{ "RxMulticastPkts", 0x260 },
{ "RxBroadcastPkts", 0x270 },
{ "RxSAChanges", 0x280 },
{ "RxFragments", 0x290 },
{ "RxJumboPkt", 0x2a0 },
{ "RxSymblErr", 0x2b0 },
{ "InRangeErrCount", 0x2c0 },
{ "OutRangeErrCount", 0x2d0 },
{ "EEELpiEvent", 0x2e0 },
{ "EEELpiDuration", 0x2f0 },
{ "RxDiscard", 0x300, 8 },
{ "TxQPKTQ6", 0x320 },
{ "TxQPKTQ7", 0x330 },
{ "TxPkts64Octets", 0x340 },
{ "TxPkts65to127Octets", 0x350 },
{ "TxPkts128to255Octets", 0x360 },
{ "TxPkts256to511Ocets", 0x370 },
{ "TxPkts512to1023Ocets", 0x380 },
{ "TxPkts1024toMaxPktOcets", 0x390 },
};
#define BCM_SF2_STATS_SIZE ARRAY_SIZE(bcm_sf2_mib)
static void bcm_sf2_sw_get_strings(struct dsa_switch *ds,
int port, uint8_t *data)
{
unsigned int i;
for (i = 0; i < BCM_SF2_STATS_SIZE; i++)
memcpy(data + i * ETH_GSTRING_LEN,
bcm_sf2_mib[i].string, ETH_GSTRING_LEN);
}
static void bcm_sf2_sw_get_ethtool_stats(struct dsa_switch *ds,
int port, uint64_t *data)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
const struct bcm_sf2_hw_stats *s;
unsigned int i;
u64 val = 0;
u32 offset;
mutex_lock(&priv->stats_mutex);
/* Now fetch the per-port counters */
for (i = 0; i < BCM_SF2_STATS_SIZE; i++) {
s = &bcm_sf2_mib[i];
/* Do a latched 64-bit read if needed */
offset = s->reg + CORE_P_MIB_OFFSET(port);
if (s->sizeof_stat == 8)
val = core_readq(priv, offset);
else
val = core_readl(priv, offset);
data[i] = (u64)val;
}
mutex_unlock(&priv->stats_mutex);
}
static int bcm_sf2_sw_get_sset_count(struct dsa_switch *ds)
{
return BCM_SF2_STATS_SIZE;
}
static char *bcm_sf2_sw_probe(struct mii_bus *bus, int sw_addr)
{
return "Broadcom Starfighter 2";
}
static void bcm_sf2_imp_setup(struct dsa_switch *ds, int port)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
unsigned int i;
u32 reg, val;
/* Enable the port memories */
reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
/* Enable Broadcast, Multicast, Unicast forwarding to IMP port */
reg = core_readl(priv, CORE_IMP_CTL);
reg |= (RX_BCST_EN | RX_MCST_EN | RX_UCST_EN);
reg &= ~(RX_DIS | TX_DIS);
core_writel(priv, reg, CORE_IMP_CTL);
/* Enable forwarding */
core_writel(priv, SW_FWDG_EN, CORE_SWMODE);
/* Enable IMP port in dumb mode */
reg = core_readl(priv, CORE_SWITCH_CTRL);
reg |= MII_DUMB_FWDG_EN;
core_writel(priv, reg, CORE_SWITCH_CTRL);
/* Resolve which bit controls the Broadcom tag */
switch (port) {
case 8:
val = BRCM_HDR_EN_P8;
break;
case 7:
val = BRCM_HDR_EN_P7;
break;
case 5:
val = BRCM_HDR_EN_P5;
break;
default:
val = 0;
break;
}
/* Enable Broadcom tags for IMP port */
reg = core_readl(priv, CORE_BRCM_HDR_CTRL);
reg |= val;
core_writel(priv, reg, CORE_BRCM_HDR_CTRL);
/* Enable reception Broadcom tag for CPU TX (switch RX) to
* allow us to tag outgoing frames
*/
reg = core_readl(priv, CORE_BRCM_HDR_RX_DIS);
reg &= ~(1 << port);
core_writel(priv, reg, CORE_BRCM_HDR_RX_DIS);
/* Enable transmission of Broadcom tags from the switch (CPU RX) to
* allow delivering frames to the per-port net_devices
*/
reg = core_readl(priv, CORE_BRCM_HDR_TX_DIS);
reg &= ~(1 << port);
core_writel(priv, reg, CORE_BRCM_HDR_TX_DIS);
/* Force link status for IMP port */
reg = core_readl(priv, CORE_STS_OVERRIDE_IMP);
reg |= (MII_SW_OR | LINK_STS);
core_writel(priv, reg, CORE_STS_OVERRIDE_IMP);
/* Enable the IMP Port to be in the same VLAN as the other ports
* on a per-port basis such that we only have Port i and IMP in
* the same VLAN.
*/
for (i = 0; i < priv->hw_params.num_ports; i++) {
if (!((1 << i) & ds->phys_port_mask))
continue;
reg = core_readl(priv, CORE_PORT_VLAN_CTL_PORT(i));
reg |= (1 << port);
core_writel(priv, reg, CORE_PORT_VLAN_CTL_PORT(i));
}
}
static void bcm_sf2_port_setup(struct dsa_switch *ds, int port)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
u32 reg;
/* Clear the memory power down */
reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
reg &= ~P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
/* Clear the Rx and Tx disable bits and set to no spanning tree */
core_writel(priv, 0, CORE_G_PCTL_PORT(port));
/* Enable port 7 interrupts to get notified */
if (port == 7)
intrl2_1_mask_clear(priv, P_IRQ_MASK(P7_IRQ_OFF));
/* Set this port, and only this one to be in the default VLAN */
reg = core_readl(priv, CORE_PORT_VLAN_CTL_PORT(port));
reg &= ~PORT_VLAN_CTRL_MASK;
reg |= (1 << port);
core_writel(priv, reg, CORE_PORT_VLAN_CTL_PORT(port));
}
static void bcm_sf2_port_disable(struct dsa_switch *ds, int port)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
u32 off, reg;
if (dsa_is_cpu_port(ds, port))
off = CORE_IMP_CTL;
else
off = CORE_G_PCTL_PORT(port);
reg = core_readl(priv, off);
reg |= RX_DIS | TX_DIS;
core_writel(priv, reg, off);
/* Power down the port memory */
reg = core_readl(priv, CORE_MEM_PSM_VDD_CTRL);
reg |= P_TXQ_PSM_VDD(port);
core_writel(priv, reg, CORE_MEM_PSM_VDD_CTRL);
}
static irqreturn_t bcm_sf2_switch_0_isr(int irq, void *dev_id)
{
struct bcm_sf2_priv *priv = dev_id;
priv->irq0_stat = intrl2_0_readl(priv, INTRL2_CPU_STATUS) &
~priv->irq0_mask;
intrl2_0_writel(priv, priv->irq0_stat, INTRL2_CPU_CLEAR);
return IRQ_HANDLED;
}
static irqreturn_t bcm_sf2_switch_1_isr(int irq, void *dev_id)
{
struct bcm_sf2_priv *priv = dev_id;
priv->irq1_stat = intrl2_1_readl(priv, INTRL2_CPU_STATUS) &
~priv->irq1_mask;
intrl2_1_writel(priv, priv->irq1_stat, INTRL2_CPU_CLEAR);
if (priv->irq1_stat & P_LINK_UP_IRQ(P7_IRQ_OFF))
priv->port_sts[7].link = 1;
if (priv->irq1_stat & P_LINK_DOWN_IRQ(P7_IRQ_OFF))
priv->port_sts[7].link = 0;
return IRQ_HANDLED;
}
static int bcm_sf2_sw_setup(struct dsa_switch *ds)
{
const char *reg_names[BCM_SF2_REGS_NUM] = BCM_SF2_REGS_NAME;
struct bcm_sf2_priv *priv = ds_to_priv(ds);
struct device_node *dn;
void __iomem **base;
unsigned int port;
unsigned int i;
u32 reg, rev;
int ret;
spin_lock_init(&priv->indir_lock);
mutex_init(&priv->stats_mutex);
/* All the interesting properties are at the parent device_node
* level
*/
dn = ds->pd->of_node->parent;
priv->irq0 = irq_of_parse_and_map(dn, 0);
priv->irq1 = irq_of_parse_and_map(dn, 1);
base = &priv->core;
for (i = 0; i < BCM_SF2_REGS_NUM; i++) {
*base = of_iomap(dn, i);
if (*base == NULL) {
pr_err("unable to find register: %s\n", reg_names[i]);
return -ENODEV;
}
base++;
}
/* Disable all interrupts and request them */
intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_MASK_SET);
intrl2_0_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
intrl2_0_writel(priv, 0, INTRL2_CPU_MASK_CLEAR);
intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_MASK_SET);
intrl2_1_writel(priv, 0xffffffff, INTRL2_CPU_CLEAR);
intrl2_1_writel(priv, 0, INTRL2_CPU_MASK_CLEAR);
ret = request_irq(priv->irq0, bcm_sf2_switch_0_isr, 0,
"switch_0", priv);
if (ret < 0) {
pr_err("failed to request switch_0 IRQ\n");
goto out_unmap;
}
ret = request_irq(priv->irq1, bcm_sf2_switch_1_isr, 0,
"switch_1", priv);
if (ret < 0) {
pr_err("failed to request switch_1 IRQ\n");
goto out_free_irq0;
}
/* Reset the MIB counters */
reg = core_readl(priv, CORE_GMNCFGCFG);
reg |= RST_MIB_CNT;
core_writel(priv, reg, CORE_GMNCFGCFG);
reg &= ~RST_MIB_CNT;
core_writel(priv, reg, CORE_GMNCFGCFG);
/* Get the maximum number of ports for this switch */
priv->hw_params.num_ports = core_readl(priv, CORE_IMP0_PRT_ID) + 1;
if (priv->hw_params.num_ports > DSA_MAX_PORTS)
priv->hw_params.num_ports = DSA_MAX_PORTS;
/* Assume a single GPHY setup if we can't read that property */
if (of_property_read_u32(dn, "brcm,num-gphy",
&priv->hw_params.num_gphy))
priv->hw_params.num_gphy = 1;
/* Enable all valid ports and disable those unused */
for (port = 0; port < priv->hw_params.num_ports; port++) {
/* IMP port receives special treatment */
if ((1 << port) & ds->phys_port_mask)
bcm_sf2_port_setup(ds, port);
else if (dsa_is_cpu_port(ds, port))
bcm_sf2_imp_setup(ds, port);
else
bcm_sf2_port_disable(ds, port);
}
/* Include the pseudo-PHY address and the broadcast PHY address to
* divert reads towards our workaround
*/
ds->phys_mii_mask |= ((1 << 30) | (1 << 0));
rev = reg_readl(priv, REG_SWITCH_REVISION);
priv->hw_params.top_rev = (rev >> SWITCH_TOP_REV_SHIFT) &
SWITCH_TOP_REV_MASK;
priv->hw_params.core_rev = (rev & SF2_REV_MASK);
pr_info("Starfighter 2 top: %x.%02x, core: %x.%02x base: 0x%p, IRQs: %d, %d\n",
priv->hw_params.top_rev >> 8, priv->hw_params.top_rev & 0xff,
priv->hw_params.core_rev >> 8, priv->hw_params.core_rev & 0xff,
priv->core, priv->irq0, priv->irq1);
return 0;
out_free_irq0:
free_irq(priv->irq0, priv);
out_unmap:
base = &priv->core;
for (i = 0; i < BCM_SF2_REGS_NUM; i++) {
iounmap(*base);
base++;
}
return ret;
}
static int bcm_sf2_sw_set_addr(struct dsa_switch *ds, u8 *addr)
{
return 0;
}
static int bcm_sf2_sw_indir_rw(struct dsa_switch *ds, int op, int addr,
int regnum, u16 val)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
int ret = 0;
u32 reg;
reg = reg_readl(priv, REG_SWITCH_CNTRL);
reg |= MDIO_MASTER_SEL;
reg_writel(priv, reg, REG_SWITCH_CNTRL);
/* Page << 8 | offset */
reg = 0x70;
reg <<= 2;
core_writel(priv, addr, reg);
/* Page << 8 | offset */
reg = 0x80 << 8 | regnum << 1;
reg <<= 2;
if (op)
ret = core_readl(priv, reg);
else
core_writel(priv, val, reg);
reg = reg_readl(priv, REG_SWITCH_CNTRL);
reg &= ~MDIO_MASTER_SEL;
reg_writel(priv, reg, REG_SWITCH_CNTRL);
return ret & 0xffff;
}
static int bcm_sf2_sw_phy_read(struct dsa_switch *ds, int addr, int regnum)
{
/* Intercept reads from the MDIO broadcast address or Broadcom
* pseudo-PHY address
*/
switch (addr) {
case 0:
case 30:
return bcm_sf2_sw_indir_rw(ds, 1, addr, regnum, 0);
default:
return 0xffff;
}
}
static int bcm_sf2_sw_phy_write(struct dsa_switch *ds, int addr, int regnum,
u16 val)
{
/* Intercept writes to the MDIO broadcast address or Broadcom
* pseudo-PHY address
*/
switch (addr) {
case 0:
case 30:
bcm_sf2_sw_indir_rw(ds, 0, addr, regnum, val);
break;
}
return 0;
}
static void bcm_sf2_sw_adjust_link(struct dsa_switch *ds, int port,
struct phy_device *phydev)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
u32 id_mode_dis = 0, port_mode;
const char *str = NULL;
u32 reg;
switch (phydev->interface) {
case PHY_INTERFACE_MODE_RGMII:
str = "RGMII (no delay)";
id_mode_dis = 1;
case PHY_INTERFACE_MODE_RGMII_TXID:
if (!str)
str = "RGMII (TX delay)";
port_mode = EXT_GPHY;
break;
case PHY_INTERFACE_MODE_MII:
str = "MII";
port_mode = EXT_EPHY;
break;
case PHY_INTERFACE_MODE_REVMII:
str = "Reverse MII";
port_mode = EXT_REVMII;
break;
default:
goto force_link;
}
/* Clear id_mode_dis bit, and the existing port mode, but
* make sure we enable the RGMII block for data to pass
*/
reg = reg_readl(priv, REG_RGMII_CNTRL_P(port));
reg &= ~ID_MODE_DIS;
reg &= ~(PORT_MODE_MASK << PORT_MODE_SHIFT);
reg &= ~(RX_PAUSE_EN | TX_PAUSE_EN);
reg |= port_mode | RGMII_MODE_EN;
if (id_mode_dis)
reg |= ID_MODE_DIS;
if (phydev->pause) {
if (phydev->asym_pause)
reg |= TX_PAUSE_EN;
reg |= RX_PAUSE_EN;
}
reg_writel(priv, reg, REG_RGMII_CNTRL_P(port));
pr_info("Port %d configured for %s\n", port, str);
force_link:
/* Force link settings detected from the PHY */
reg = SW_OVERRIDE;
switch (phydev->speed) {
case SPEED_1000:
reg |= SPDSTS_1000 << SPEED_SHIFT;
break;
case SPEED_100:
reg |= SPDSTS_100 << SPEED_SHIFT;
break;
}
if (phydev->link)
reg |= LINK_STS;
if (phydev->duplex == DUPLEX_FULL)
reg |= DUPLX_MODE;
core_writel(priv, reg, CORE_STS_OVERRIDE_GMIIP_PORT(port));
}
static void bcm_sf2_sw_fixed_link_update(struct dsa_switch *ds, int port,
struct fixed_phy_status *status)
{
struct bcm_sf2_priv *priv = ds_to_priv(ds);
u32 link, duplex, pause, speed;
u32 reg;
link = core_readl(priv, CORE_LNKSTS);
duplex = core_readl(priv, CORE_DUPSTS);
pause = core_readl(priv, CORE_PAUSESTS);
speed = core_readl(priv, CORE_SPDSTS);
speed >>= (port * SPDSTS_SHIFT);
speed &= SPDSTS_MASK;
status->link = 0;
/* Port 7 is special as we do not get link status from CORE_LNKSTS,
* which means that we need to force the link at the port override
* level to get the data to flow. We do use what the interrupt handler
* did determine before.
*/
if (port == 7) {
status->link = priv->port_sts[port].link;
reg = core_readl(priv, CORE_STS_OVERRIDE_GMIIP_PORT(7));
reg |= SW_OVERRIDE;
if (status->link)
reg |= LINK_STS;
else
reg &= ~LINK_STS;
core_writel(priv, reg, CORE_STS_OVERRIDE_GMIIP_PORT(7));
status->duplex = 1;
} else {
status->link = !!(link & (1 << port));
status->duplex = !!(duplex & (1 << port));
}
switch (speed) {
case SPDSTS_10:
status->speed = SPEED_10;
break;
case SPDSTS_100:
status->speed = SPEED_100;
break;
case SPDSTS_1000:
status->speed = SPEED_1000;
break;
}
if ((pause & (1 << port)) &&
(pause & (1 << (port + PAUSESTS_TX_PAUSE_SHIFT)))) {
status->asym_pause = 1;
status->pause = 1;
}
if (pause & (1 << port))
status->pause = 1;
}
static struct dsa_switch_driver bcm_sf2_switch_driver = {
.tag_protocol = htons(ETH_P_BRCMTAG),
.priv_size = sizeof(struct bcm_sf2_priv),
.probe = bcm_sf2_sw_probe,
.setup = bcm_sf2_sw_setup,
.set_addr = bcm_sf2_sw_set_addr,
.phy_read = bcm_sf2_sw_phy_read,
.phy_write = bcm_sf2_sw_phy_write,
.get_strings = bcm_sf2_sw_get_strings,
.get_ethtool_stats = bcm_sf2_sw_get_ethtool_stats,
.get_sset_count = bcm_sf2_sw_get_sset_count,
.adjust_link = bcm_sf2_sw_adjust_link,
.fixed_link_update = bcm_sf2_sw_fixed_link_update,
};
static int __init bcm_sf2_init(void)
{
register_switch_driver(&bcm_sf2_switch_driver);
return 0;
}
module_init(bcm_sf2_init);
static void __exit bcm_sf2_exit(void)
{
unregister_switch_driver(&bcm_sf2_switch_driver);
}
module_exit(bcm_sf2_exit);
MODULE_AUTHOR("Broadcom Corporation");
MODULE_DESCRIPTION("Driver for Broadcom Starfighter 2 ethernet switch chip");
MODULE_LICENSE("GPL");
MODULE_ALIAS("platform:brcm-sf2");
/*
* Broadcom Starfighter2 private context
*
* Copyright (C) 2014, Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __BCM_SF2_H
#define __BCM_SF2_H
#include <linux/platform_device.h>
#include <linux/kernel.h>
#include <linux/io.h>
#include <linux/spinlock.h>
#include <linux/mutex.h>
#include <linux/mii.h>
#include <net/dsa.h>
#include "bcm_sf2_regs.h"
struct bcm_sf2_hw_params {
u16 top_rev;
u16 core_rev;
u32 num_gphy;
u8 num_acb_queue;
u8 num_rgmii;
u8 num_ports;
u8 fcb_pause_override:1;
u8 acb_packets_inflight:1;
};
#define BCM_SF2_REGS_NAME {\
"core", "reg", "intrl2_0", "intrl2_1", "fcb", "acb" \
}
#define BCM_SF2_REGS_NUM 6
struct bcm_sf2_port_status {
unsigned int link;
};
struct bcm_sf2_priv {
/* Base registers, keep those in order with BCM_SF2_REGS_NAME */
void __iomem *core;
void __iomem *reg;
void __iomem *intrl2_0;
void __iomem *intrl2_1;
void __iomem *fcb;
void __iomem *acb;
/* spinlock protecting access to the indirect registers */
spinlock_t indir_lock;
int irq0;
int irq1;
u32 irq0_stat;
u32 irq0_mask;
u32 irq1_stat;
u32 irq1_mask;
/* Mutex protecting access to the MIB counters */
struct mutex stats_mutex;
struct bcm_sf2_hw_params hw_params;
struct bcm_sf2_port_status port_sts[DSA_MAX_PORTS];
};
struct bcm_sf2_hw_stats {
const char *string;
u16 reg;
u8 sizeof_stat;
};
#define SF2_IO_MACRO(name) \
static inline u32 name##_readl(struct bcm_sf2_priv *priv, u32 off) \
{ \
return __raw_readl(priv->name + off); \
} \
static inline void name##_writel(struct bcm_sf2_priv *priv, \
u32 val, u32 off) \
{ \
__raw_writel(val, priv->name + off); \
} \
/* Accesses to 64-bits register requires us to latch the hi/lo pairs
* using the REG_DIR_DATA_{READ,WRITE} ancillary registers. The 'indir_lock'
* spinlock is automatically grabbed and released to provide relative
* atomiticy with latched reads/writes.
*/
#define SF2_IO64_MACRO(name) \
static inline u64 name##_readq(struct bcm_sf2_priv *priv, u32 off) \
{ \
u32 indir, dir; \
spin_lock(&priv->indir_lock); \
indir = reg_readl(priv, REG_DIR_DATA_READ); \
dir = __raw_readl(priv->name + off); \
spin_unlock(&priv->indir_lock); \
return (u64)indir << 32 | dir; \
} \
static inline void name##_writeq(struct bcm_sf2_priv *priv, u32 off, \
u64 val) \
{ \
spin_lock(&priv->indir_lock); \
reg_writel(priv, upper_32_bits(val), REG_DIR_DATA_WRITE); \
__raw_writel(lower_32_bits(val), priv->name + off); \
spin_unlock(&priv->indir_lock); \
}
#define SWITCH_INTR_L2(which) \
static inline void intrl2_##which##_mask_clear(struct bcm_sf2_priv *priv, \
u32 mask) \
{ \
intrl2_##which##_writel(priv, mask, INTRL2_CPU_MASK_CLEAR); \
priv->irq##which##_mask &= ~(mask); \
} \
static inline void intrl2_##which##_mask_set(struct bcm_sf2_priv *priv, \
u32 mask) \
{ \
intrl2_## which##_writel(priv, mask, INTRL2_CPU_MASK_SET); \
priv->irq##which##_mask |= (mask); \
} \
SF2_IO_MACRO(core);
SF2_IO_MACRO(reg);
SF2_IO64_MACRO(core);
SF2_IO_MACRO(intrl2_0);
SF2_IO_MACRO(intrl2_1);
SF2_IO_MACRO(fcb);
SF2_IO_MACRO(acb);
SWITCH_INTR_L2(0);
SWITCH_INTR_L2(1);
#endif /* __BCM_SF2_H */
/*
* Broadcom Starfighter 2 switch register defines
*
* Copyright (C) 2014, Broadcom Corporation
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License as published by
* the Free Software Foundation; either version 2 of the License, or
* (at your option) any later version.
*/
#ifndef __BCM_SF2_REGS_H
#define __BCM_SF2_REGS_H
/* Register set relative to 'REG' */
#define REG_SWITCH_CNTRL 0x00
#define MDIO_MASTER_SEL (1 << 0)
#define REG_SWITCH_STATUS 0x04
#define REG_DIR_DATA_WRITE 0x08
#define REG_DIR_DATA_READ 0x0C
#define REG_SWITCH_REVISION 0x18
#define SF2_REV_MASK 0xffff
#define SWITCH_TOP_REV_SHIFT 16
#define SWITCH_TOP_REV_MASK 0xffff
#define REG_PHY_REVISION 0x1C
#define REG_SPHY_CNTRL 0x2C
#define IDDQ_BIAS (1 << 0)
#define EXT_PWR_DOWN (1 << 1)
#define FORCE_DLL_EN (1 << 2)
#define IDDQ_GLOBAL_PWR (1 << 3)
#define CK25_DIS (1 << 4)
#define PHY_RESET (1 << 5)
#define PHY_PHYAD_SHIFT 8
#define PHY_PHYAD_MASK 0x1F
#define REG_RGMII_0_BASE 0x34
#define REG_RGMII_CNTRL 0x00
#define REG_RGMII_IB_STATUS 0x04
#define REG_RGMII_RX_CLOCK_DELAY_CNTRL 0x08
#define REG_RGMII_CNTRL_SIZE 0x0C
#define REG_RGMII_CNTRL_P(x) (REG_RGMII_0_BASE + \
((x) * REG_RGMII_CNTRL_SIZE))
/* Relative to REG_RGMII_CNTRL */
#define RGMII_MODE_EN (1 << 0)
#define ID_MODE_DIS (1 << 1)
#define PORT_MODE_SHIFT 2
#define INT_EPHY (0 << PORT_MODE_SHIFT)
#define INT_GPHY (1 << PORT_MODE_SHIFT)
#define EXT_EPHY (2 << PORT_MODE_SHIFT)
#define EXT_GPHY (3 << PORT_MODE_SHIFT)
#define EXT_REVMII (4 << PORT_MODE_SHIFT)
#define PORT_MODE_MASK 0x7
#define RVMII_REF_SEL (1 << 5)
#define RX_PAUSE_EN (1 << 6)
#define TX_PAUSE_EN (1 << 7)
#define TX_CLK_STOP_EN (1 << 8)
#define LPI_COUNT_SHIFT 9
#define LPI_COUNT_MASK 0x3F
/* Register set relative to 'INTRL2_0' and 'INTRL2_1' */
#define INTRL2_CPU_STATUS 0x00
#define INTRL2_CPU_SET 0x04
#define INTRL2_CPU_CLEAR 0x08
#define INTRL2_CPU_MASK_STATUS 0x0c
#define INTRL2_CPU_MASK_SET 0x10
#define INTRL2_CPU_MASK_CLEAR 0x14
/* Shared INTRL2_0 and INTRL2_ interrupt sources macros */
#define P_LINK_UP_IRQ(x) (1 << (0 + (x)))
#define P_LINK_DOWN_IRQ(x) (1 << (1 + (x)))
#define P_ENERGY_ON_IRQ(x) (1 << (2 + (x)))
#define P_ENERGY_OFF_IRQ(x) (1 << (3 + (x)))
#define P_GPHY_IRQ(x) (1 << (4 + (x)))
#define P_NUM_IRQ 5
#define P_IRQ_MASK(x) (P_LINK_UP_IRQ((x)) | \
P_LINK_DOWN_IRQ((x)) | \
P_ENERGY_ON_IRQ((x)) | \
P_ENERGY_OFF_IRQ((x)) | \
P_GPHY_IRQ((x)))
/* INTRL2_0 interrupt sources */
#define P0_IRQ_OFF 0
#define MEM_DOUBLE_IRQ (1 << 5)
#define EEE_LPI_IRQ (1 << 6)
#define P5_CPU_WAKE_IRQ (1 << 7)
#define P8_CPU_WAKE_IRQ (1 << 8)
#define P7_CPU_WAKE_IRQ (1 << 9)
#define IEEE1588_IRQ (1 << 10)
#define MDIO_ERR_IRQ (1 << 11)
#define MDIO_DONE_IRQ (1 << 12)
#define GISB_ERR_IRQ (1 << 13)
#define UBUS_ERR_IRQ (1 << 14)
#define FAILOVER_ON_IRQ (1 << 15)
#define FAILOVER_OFF_IRQ (1 << 16)
#define TCAM_SOFT_ERR_IRQ (1 << 17)
/* INTRL2_1 interrupt sources */
#define P7_IRQ_OFF 0
#define P_IRQ_OFF(x) ((6 - (x)) * P_NUM_IRQ)
/* Register set relative to 'CORE' */
#define CORE_G_PCTL_PORT0 0x00000
#define CORE_G_PCTL_PORT(x) (CORE_G_PCTL_PORT0 + (x * 0x4))
#define CORE_IMP_CTL 0x00020
#define RX_DIS (1 << 0)
#define TX_DIS (1 << 1)
#define RX_BCST_EN (1 << 2)
#define RX_MCST_EN (1 << 3)
#define RX_UCST_EN (1 << 4)
#define G_MISTP_STATE_SHIFT 5
#define G_MISTP_NO_STP (0 << G_MISTP_STATE_SHIFT)
#define G_MISTP_DIS_STATE (1 << G_MISTP_STATE_SHIFT)
#define G_MISTP_BLOCK_STATE (2 << G_MISTP_STATE_SHIFT)
#define G_MISTP_LISTEN_STATE (3 << G_MISTP_STATE_SHIFT)
#define G_MISTP_LEARN_STATE (4 << G_MISTP_STATE_SHIFT)
#define G_MISTP_FWD_STATE (5 << G_MISTP_STATE_SHIFT)
#define G_MISTP_STATE_MASK 0x7
#define CORE_SWMODE 0x0002c
#define SW_FWDG_MODE (1 << 0)
#define SW_FWDG_EN (1 << 1)
#define RTRY_LMT_DIS (1 << 2)
#define CORE_STS_OVERRIDE_IMP 0x00038
#define GMII_SPEED_UP_2G (1 << 6)
#define MII_SW_OR (1 << 7)
#define CORE_NEW_CTRL 0x00084
#define IP_MC (1 << 0)
#define OUTRANGEERR_DISCARD (1 << 1)
#define INRANGEERR_DISCARD (1 << 2)
#define CABLE_DIAG_LEN (1 << 3)
#define OVERRIDE_AUTO_PD_WAR (1 << 4)
#define EN_AUTO_PD_WAR (1 << 5)
#define UC_FWD_EN (1 << 6)
#define MC_FWD_EN (1 << 7)
#define CORE_SWITCH_CTRL 0x00088
#define MII_DUMB_FWDG_EN (1 << 6)
#define CORE_SFT_LRN_CTRL 0x000f8
#define SW_LEARN_CNTL(x) (1 << (x))
#define CORE_STS_OVERRIDE_GMIIP_PORT(x) (0x160 + (x) * 4)
#define LINK_STS (1 << 0)
#define DUPLX_MODE (1 << 1)
#define SPEED_SHIFT 2
#define SPEED_MASK 0x3
#define RXFLOW_CNTL (1 << 4)
#define TXFLOW_CNTL (1 << 5)
#define SW_OVERRIDE (1 << 6)
#define CORE_WATCHDOG_CTRL 0x001e4
#define SOFTWARE_RESET (1 << 7)
#define EN_CHIP_RST (1 << 6)
#define EN_SW_RESET (1 << 4)
#define CORE_LNKSTS 0x00400
#define LNK_STS_MASK 0x1ff
#define CORE_SPDSTS 0x00410
#define SPDSTS_10 0
#define SPDSTS_100 1
#define SPDSTS_1000 2
#define SPDSTS_SHIFT 2
#define SPDSTS_MASK 0x3
#define CORE_DUPSTS 0x00420
#define CORE_DUPSTS_MASK 0x1ff
#define CORE_PAUSESTS 0x00428
#define PAUSESTS_TX_PAUSE_SHIFT 9
#define CORE_GMNCFGCFG 0x0800
#define RST_MIB_CNT (1 << 0)
#define RXBPDU_EN (1 << 1)
#define CORE_IMP0_PRT_ID 0x0804
#define CORE_BRCM_HDR_CTRL 0x0080c
#define BRCM_HDR_EN_P8 (1 << 0)
#define BRCM_HDR_EN_P5 (1 << 1)
#define BRCM_HDR_EN_P7 (1 << 2)
#define CORE_BRCM_HDR_CTRL2 0x0828
#define CORE_HL_PRTC_CTRL 0x0940
#define ARP_EN (1 << 0)
#define RARP_EN (1 << 1)
#define DHCP_EN (1 << 2)
#define ICMPV4_EN (1 << 3)
#define ICMPV6_EN (1 << 4)
#define ICMPV6_FWD_MODE (1 << 5)
#define IGMP_DIP_EN (1 << 8)
#define IGMP_RPTLVE_EN (1 << 9)
#define IGMP_RTPLVE_FWD_MODE (1 << 10)
#define IGMP_QRY_EN (1 << 11)
#define IGMP_QRY_FWD_MODE (1 << 12)
#define IGMP_UKN_EN (1 << 13)
#define IGMP_UKN_FWD_MODE (1 << 14)
#define MLD_RPTDONE_EN (1 << 15)
#define MLD_RPTDONE_FWD_MODE (1 << 16)
#define MLD_QRY_EN (1 << 17)
#define MLD_QRY_FWD_MODE (1 << 18)
#define CORE_RST_MIB_CNT_EN 0x0950
#define CORE_BRCM_HDR_RX_DIS 0x0980
#define CORE_BRCM_HDR_TX_DIS 0x0988
#define CORE_MEM_PSM_VDD_CTRL 0x2380
#define P_TXQ_PSM_VDD_SHIFT 2
#define P_TXQ_PSM_VDD_MASK 0x3
#define P_TXQ_PSM_VDD(x) (P_TXQ_PSM_VDD_MASK << \
((x) * P_TXQ_PSM_VDD_SHIFT))
#define CORE_P0_MIB_OFFSET 0x8000
#define P_MIB_SIZE 0x400
#define CORE_P_MIB_OFFSET(x) (CORE_P0_MIB_OFFSET + (x) * P_MIB_SIZE)
#define CORE_PORT_VLAN_CTL_PORT(x) (0xc400 + ((x) * 0x8))
#define PORT_VLAN_CTRL_MASK 0x1ff
#endif /* __BCM_SF2_REGS_H */
......@@ -635,6 +635,7 @@ struct packet_type dsa_pack_type __read_mostly = {
};
static const struct of_device_id dsa_of_match_table[] = {
{ .compatible = "brcm,bcm7445-switch-v4.0" },
{ .compatible = "marvell,dsa", },
{}
};
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment