Merge branch 'next-s3c' of git://aeryn.fluff.org.uk/bjdooks/linux into devel-stable

Documentation/arm/Samsung-S3C24XX/CPUfreq.txt

+		S3C24XX CPUfreq support
+		=======================
+
+Introduction
+------------
+
+ The S3C24XX series support a number of power saving systems, such as
+ the ability to change the core, memory and peripheral operating
+ frequencies. The core control is exported via the CPUFreq driver
+ which has a number of different manual or automatic controls over the
+ rate the core is running at.
+
+ There are two forms of the driver depending on the specific CPU and
+ how the clocks are arranged. The first implementation used as single
+ PLL to feed the ARM, memory and peripherals via a series of dividers
+ and muxes and this is the implementation that is documented here. A
+ newer version where there is a seperate PLL and clock divider for the
+ ARM core is available as a seperate driver.
+
+
+Layout
+------
+
+ The code core manages the CPU specific drivers, any data that they
+ need to register and the interface to the generic drivers/cpufreq
+ system. Each CPU registers a driver to control the PLL, clock dividers
+ and anything else associated with it. Any board that wants to use this
+ framework needs to supply at least basic details of what is required.
+
+ The core registers with drivers/cpufreq at init time if all the data
+ necessary has been supplied.
+
+
+CPU support
+-----------
+
+ The support for each CPU depends on the facilities provided by the
+ SoC and the driver as each device has different PLL and clock chains
+ associated with it.
+
+
+Slow Mode
+---------
+
+ The SLOW mode where the PLL is turned off altogether and the
+ system is fed by the external crystal input is currently not
+ supported.
+
+
+sysfs
+-----
+
+ The core code exports extra information via sysfs in the directory
+ devices/system/cpu/cpu0/arch-freq.
+
+
+Board Support
+-------------
+
+ Each board that wants to use the cpufreq code must register some basic
+ information with the core driver to provide information about what the
+ board requires and any restrictions being placed on it.
+
+ The board needs to supply information about whether it needs the IO bank
+ timings changing, any maximum frequency limits and information about the
+ SDRAM refresh rate.
+
+
+
+
+Document Author
+---------------
+
+Ben Dooks, Copyright 2009 Simtec Electronics
+Licensed under GPLv2

arch/arm/Kconfig

@@ -122,6 +122,13 @@ config ARCH_HAS_ILOG2_U32
 config ARCH_HAS_ILOG2_U64
 	bool
 
+config ARCH_HAS_CPUFREQ
+	bool
+	help
+	  Internal node to signify that the ARCH has CPUFREQ support
+	  and that the relevant menu configurations are displayed for
+	  it.
+
 config GENERIC_HWEIGHT
 	bool
 	default y
@@ -206,6 +213,7 @@ config ARCH_AAEC2000
 config ARCH_INTEGRATOR
 	bool "ARM Ltd. Integrator family"
 	select ARM_AMBA
+	select ARCH_HAS_CPUFREQ
 	select HAVE_CLK
 	select COMMON_CLKDEV
 	select ICST525
@@ -512,6 +520,7 @@ config ARCH_PXA
 	bool "PXA2xx/PXA3xx-based"
 	depends on MMU
 	select ARCH_MTD_XIP
+	select ARCH_HAS_CPUFREQ
 	select GENERIC_GPIO
 	select HAVE_CLK
 	select COMMON_CLKDEV
@@ -554,6 +563,7 @@ config ARCH_SA1100
 	select ISA
 	select ARCH_SPARSEMEM_ENABLE
 	select ARCH_MTD_XIP
+	select ARCH_HAS_CPUFREQ
 	select GENERIC_GPIO
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
@@ -566,6 +576,7 @@ config ARCH_SA1100
 config ARCH_S3C2410
 	bool "Samsung S3C2410, S3C2412, S3C2413, S3C2440, S3C2442, S3C2443"
 	select GENERIC_GPIO
+	select ARCH_HAS_CPUFREQ
 	select HAVE_CLK
 	help
 	  Samsung S3C2410X CPU based systems, such as the Simtec Electronics
@@ -576,9 +587,18 @@ config ARCH_S3C64XX
 	bool "Samsung S3C64XX"
 	select GENERIC_GPIO
 	select HAVE_CLK
+	select ARCH_HAS_CPUFREQ
 	help
 	  Samsung S3C64XX series based systems
 
+config ARCH_S5PC1XX
+	bool "Samsung S5PC1XX"
+	select GENERIC_GPIO
+	select HAVE_CLK
+	select CPU_V7
+	help
+	  Samsung S5PC1XX series based systems
+
 config ARCH_SHARK
 	bool "Shark"
 	select CPU_SA110
@@ -635,6 +655,7 @@ config ARCH_OMAP
 	select GENERIC_GPIO
 	select HAVE_CLK
 	select ARCH_REQUIRE_GPIOLIB
+	select ARCH_HAS_CPUFREQ
 	select GENERIC_TIME
 	select GENERIC_CLOCKEVENTS
 	help
@@ -688,6 +709,7 @@ source "arch/arm/mach-kirkwood/Kconfig"
 source "arch/arm/plat-s3c24xx/Kconfig"
 source "arch/arm/plat-s3c64xx/Kconfig"
 source "arch/arm/plat-s3c/Kconfig"
+source "arch/arm/plat-s5pc1xx/Kconfig"
 
 if ARCH_S3C2410
 source "arch/arm/mach-s3c2400/Kconfig"
@@ -705,6 +727,10 @@ endif
 
 source "arch/arm/plat-stmp3xxx/Kconfig"
 
+if ARCH_S5PC1XX
+source "arch/arm/mach-s5pc100/Kconfig"
+endif
+
 source "arch/arm/mach-lh7a40x/Kconfig"
 
 source "arch/arm/mach-h720x/Kconfig"
@@ -1248,7 +1274,7 @@ endmenu
 
 menu "CPU Power Management"
 
-if (ARCH_SA1100 || ARCH_INTEGRATOR || ARCH_OMAP || ARCH_PXA || ARCH_S3C64XX)
+if ARCH_HAS_CPUFREQ
 
 source "drivers/cpufreq/Kconfig"
 
@@ -1283,6 +1309,52 @@ config CPU_FREQ_S3C64XX
 	bool "CPUfreq support for Samsung S3C64XX CPUs"
 	depends on CPU_FREQ && CPU_S3C6410
 
+config CPU_FREQ_S3C
+	bool
+	help
+	  Internal configuration node for common cpufreq on Samsung SoC
+
+config CPU_FREQ_S3C24XX
+	bool "CPUfreq driver for Samsung S3C24XX series CPUs"
+	depends on ARCH_S3C2410 && CPU_FREQ && EXPERIMENTAL
+	select CPU_FREQ_S3C
+	help
+	  This enables the CPUfreq driver for the Samsung S3C24XX family
+	  of CPUs.
+
+	  For details, take a look at <file:Documentation/cpu-freq>.
+
+	  If in doubt, say N.
+
+config CPU_FREQ_S3C24XX_PLL
+	bool "Support CPUfreq changing of PLL frequency"
+	depends on CPU_FREQ_S3C24XX && EXPERIMENTAL
+	help
+	  Compile in support for changing the PLL frequency from the
+	  S3C24XX series CPUfreq driver. The PLL takes time to settle
+	  after a frequency change, so by default it is not enabled.
+
+	  This also means that the PLL tables for the selected CPU(s) will
+	  be built which may increase the size of the kernel image.
+
+config CPU_FREQ_S3C24XX_DEBUG
+	bool "Debug CPUfreq Samsung driver core"
+	depends on CPU_FREQ_S3C24XX
+	help
+	  Enable s3c_freq_dbg for the Samsung S3C CPUfreq core
+
+config CPU_FREQ_S3C24XX_IODEBUG
+	bool "Debug CPUfreq Samsung driver IO timing"
+	depends on CPU_FREQ_S3C24XX
+	help
+	  Enable s3c_freq_iodbg for the Samsung S3C CPUfreq core
+
+config CPU_FREQ_S3C24XX_DEBUGFS
+	bool "Export debugfs for CPUFreq"
+	depends on CPU_FREQ_S3C24XX && DEBUG_FS
+	help
+	  Export status information via debugfs.
+
 endif
 
 source "drivers/cpuidle/Kconfig"

arch/arm/Makefile

@@ -158,6 +158,7 @@ machine-$(CONFIG_ARCH_RPC)		:= rpc
 machine-$(CONFIG_ARCH_S3C2410)		:= s3c2410 s3c2400 s3c2412 s3c2440 s3c2442 s3c2443
 machine-$(CONFIG_ARCH_S3C24A0)		:= s3c24a0
 machine-$(CONFIG_ARCH_S3C64XX)		:= s3c6400 s3c6410
+machine-$(CONFIG_ARCH_S5PC1XX)		:= s5pc100
 machine-$(CONFIG_ARCH_SA1100)		:= sa1100
 machine-$(CONFIG_ARCH_SHARK)		:= shark
 machine-$(CONFIG_ARCH_STMP378X)		:= stmp378x
@@ -177,6 +178,7 @@ plat-$(CONFIG_PLAT_ORION)	:= orion
 plat-$(CONFIG_PLAT_PXA)		:= pxa
 plat-$(CONFIG_PLAT_S3C24XX)	:= s3c24xx s3c
 plat-$(CONFIG_PLAT_S3C64XX)	:= s3c64xx s3c
+plat-$(CONFIG_PLAT_S5PC1XX)	:= s5pc1xx s3c
 plat-$(CONFIG_ARCH_STMP3XXX)	:= stmp3xxx
 
 ifeq ($(CONFIG_ARCH_EBSA110),y)

arch/arm/kernel/irq.c

@@ -86,7 +86,7 @@ int show_interrupts(struct seq_file *p, void *v)
 unlock:
 		spin_unlock_irqrestore(&irq_desc[i].lock, flags);
 	} else if (i == NR_IRQS) {
-#ifdef CONFIG_ARCH_ACORN
+#ifdef CONFIG_FIQ
 		show_fiq_list(p, v);
 #endif
 #ifdef CONFIG_SMP

arch/arm/mach-s3c2410/Kconfig

@@ -12,6 +12,7 @@ config CPU_S3C2410
 	select S3C2410_GPIO
 	select CPU_LLSERIAL_S3C2410
 	select S3C2410_PM if PM
+	select S3C2410_CPUFREQ if CPU_FREQ_S3C24XX
 	help
 	  Support for S3C2410 and S3C2410A family from the S3C24XX line
 	  of Samsung Mobile CPUs.
@@ -45,6 +46,22 @@ config MACH_BAST_IDE
 	  Internal node for machines with an BAST style IDE
 	  interface
 
+# cpu frequency scaling support
+
+config S3C2410_CPUFREQ
+	bool
+	depends on CPU_FREQ_S3C24XX && CPU_S3C2410
+	select S3C2410_CPUFREQ_UTILS
+	help
+	  CPU Frequency scaling support for S3C2410
+
+config S3C2410_PLLTABLE
+	bool
+	depends on S3C2410_CPUFREQ && CPU_FREQ_S3C24XX_PLL
+	default y
+	help
+	  Select the PLL table for the S3C2410
+
 menu "S3C2410 Machines"
 
 config ARCH_SMDK2410
@@ -79,6 +96,7 @@ config MACH_N30
 config ARCH_BAST
 	bool "Simtec Electronics BAST (EB2410ITX)"
 	select CPU_S3C2410
+	select S3C2410_IOTIMING if S3C2410_CPUFREQ
 	select PM_SIMTEC if PM
 	select SIMTEC_NOR
 	select MACH_BAST_IDE

arch/arm/mach-s3c2410/Makefile

@@ -15,6 +15,8 @@ obj-$(CONFIG_CPU_S3C2410_DMA)	+= dma.o
 obj-$(CONFIG_CPU_S3C2410_DMA)	+= dma.o
 obj-$(CONFIG_S3C2410_PM)	+= pm.o sleep.o
 obj-$(CONFIG_S3C2410_GPIO)	+= gpio.o
+obj-$(CONFIG_S3C2410_CPUFREQ)	+= cpu-freq.o
+obj-$(CONFIG_S3C2410_PLLTABLE)	+= pll.o
 
 # Machine support
 

arch/arm/mach-s3c2410/cpu-freq.c

+/* linux/arch/arm/mach-s3c2410/cpu-freq.c
+ *
+ * Copyright (c) 2006,2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2410 CPU Frequency scaling
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#include <linux/sysdev.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/regs-clock.h>
+
+#include <plat/cpu.h>
+#include <plat/clock.h>
+#include <plat/cpu-freq-core.h>
+
+/* Note, 2410A has an extra mode for 1:4:4 ratio, bit 2 of CLKDIV */
+
+static void s3c2410_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
+{
+	u32 clkdiv = 0;
+
+	if (cfg->divs.h_divisor == 2)
+		clkdiv |= S3C2410_CLKDIVN_HDIVN;
+
+	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
+		clkdiv |= S3C2410_CLKDIVN_PDIVN;
+
+	__raw_writel(clkdiv, S3C2410_CLKDIVN);
+}
+
+static int s3c2410_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
+{
+	unsigned long hclk, fclk, pclk;
+	unsigned int hdiv, pdiv;
+	unsigned long hclk_max;
+
+	fclk = cfg->freq.fclk;
+	hclk_max = cfg->max.hclk;
+
+	cfg->freq.armclk = fclk;
+
+	s3c_freq_dbg("%s: fclk is %lu, max hclk %lu\n",
+		      __func__, fclk, hclk_max);
+
+	hdiv = (fclk > cfg->max.hclk) ? 2 : 1;
+	hclk = fclk / hdiv;
+
+	if (hclk > cfg->max.hclk) {
+		s3c_freq_dbg("%s: hclk too big\n", __func__);
+		return -EINVAL;
+	}
+
+	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
+	pclk = hclk / pdiv;
+
+	if (pclk > cfg->max.pclk) {
+		s3c_freq_dbg("%s: pclk too big\n", __func__);
+		return -EINVAL;
+	}
+
+	pdiv *= hdiv;
+
+	/* record the result */
+	cfg->divs.p_divisor = pdiv;
+	cfg->divs.h_divisor = hdiv;
+
+	return 0      ;
+}
+
+static struct s3c_cpufreq_info s3c2410_cpufreq_info = {
+	.max		= {
+		.fclk	= 200000000,
+		.hclk	= 100000000,
+		.pclk	=  50000000,
+	},
+
+	/* transition latency is about 5ms worst-case, so
+	 * set 10ms to be sure */
+	.latency	= 10000000,
+
+	.locktime_m	= 150,
+	.locktime_u	= 150,
+	.locktime_bits	= 12,
+
+	.need_pll	= 1,
+
+	.name		= "s3c2410",
+	.calc_iotiming	= s3c2410_iotiming_calc,
+	.set_iotiming	= s3c2410_iotiming_set,
+	.get_iotiming	= s3c2410_iotiming_get,
+	.resume_clocks	= s3c2410_setup_clocks,
+
+	.set_fvco	= s3c2410_set_fvco,
+	.set_refresh	= s3c2410_cpufreq_setrefresh,
+	.set_divs	= s3c2410_cpufreq_setdivs,
+	.calc_divs	= s3c2410_cpufreq_calcdivs,
+
+	.debug_io_show	= s3c_cpufreq_debugfs_call(s3c2410_iotiming_debugfs),
+};
+
+static int s3c2410_cpufreq_add(struct sys_device *sysdev)
+{
+	return s3c_cpufreq_register(&s3c2410_cpufreq_info);
+}
+
+static struct sysdev_driver s3c2410_cpufreq_driver = {
+	.add		= s3c2410_cpufreq_add,
+};
+
+static int __init s3c2410_cpufreq_init(void)
+{
+	return sysdev_driver_register(&s3c2410_sysclass,
+				      &s3c2410_cpufreq_driver);
+}
+
+arch_initcall(s3c2410_cpufreq_init);
+
+static int s3c2410a_cpufreq_add(struct sys_device *sysdev)
+{
+	/* alter the maximum freq settings for S3C2410A. If a board knows
+	 * it only has a maximum of 200, then it should register its own
+	 * limits. */
+
+	s3c2410_cpufreq_info.max.fclk = 266000000;
+	s3c2410_cpufreq_info.max.hclk = 133000000;
+	s3c2410_cpufreq_info.max.pclk =  66500000;
+	s3c2410_cpufreq_info.name = "s3c2410a";
+
+	return s3c2410_cpufreq_add(sysdev);
+}
+
+static struct sysdev_driver s3c2410a_cpufreq_driver = {
+	.add		= s3c2410a_cpufreq_add,
+};
+
+static int __init s3c2410a_cpufreq_init(void)
+{
+	return sysdev_driver_register(&s3c2410a_sysclass,
+				      &s3c2410a_cpufreq_driver);
+}
+
+arch_initcall(s3c2410a_cpufreq_init);

arch/arm/mach-s3c2410/dma.c

@@ -164,6 +164,17 @@ static int __init s3c2410_dma_drvinit(void)
 }
 
 arch_initcall(s3c2410_dma_drvinit);
+
+static struct sysdev_driver s3c2410a_dma_driver = {
+	.add	= s3c2410_dma_add,
+};
+
+static int __init s3c2410a_dma_drvinit(void)
+{
+	return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_dma_driver);
+}
+
+arch_initcall(s3c2410a_dma_drvinit);
 #endif
 
 #if defined(CONFIG_CPU_S3C2442)

arch/arm/mach-s3c2410/include/mach/gpio-core.h

@@ -28,7 +28,7 @@ static inline struct s3c_gpio_chip *s3c_gpiolib_getchip(unsigned int pin)
 		return NULL;
 
 	chip = &s3c24xx_gpios[pin/32];
-	return (S3C2410_GPIO_OFFSET(pin) > chip->chip.ngpio) ? chip : NULL;
+	return (S3C2410_GPIO_OFFSET(pin) < chip->chip.ngpio) ? chip : NULL;
 }
 
 #endif /* __ASM_ARCH_GPIO_CORE_H */

arch/arm/mach-s3c2410/include/mach/irqs.h

@@ -164,6 +164,12 @@
 #define IRQ_S3CUART_TX3		IRQ_S3C2443_TX3
 #define IRQ_S3CUART_ERR3	IRQ_S3C2443_ERR3
 
+#ifdef CONFIG_CPU_S3C2440
+#define IRQ_S3C244x_AC97 IRQ_S3C2440_AC97
+#else
+#define IRQ_S3C244x_AC97 IRQ_S3C2443_AC97
+#endif
+
 /* Our FIQs are routable from IRQ_EINT0 to IRQ_ADCPARENT */
 #define FIQ_START		IRQ_EINT0
 

arch/arm/mach-s3c2410/include/mach/map.h

@@ -67,6 +67,13 @@
 #define S3C2443_PA_HSMMC   (0x4A800000)
 #define S3C2443_SZ_HSMMC   (256)
 
+/* S3C2412 memory and IO controls */
+#define S3C2412_PA_SSMC	(0x4F000000)
+#define S3C2412_VA_SSMC	S3C_ADDR_CPU(0x00000000)
+
+#define S3C2412_PA_EBI	(0x48800000)
+#define S3C2412_VA_EBI	S3C_ADDR_CPU(0x00010000)
+
 /* physical addresses of all the chip-select areas */
 
 #define S3C2410_CS0 (0x00000000)
@@ -103,5 +110,6 @@
 #define S3C_PA_UART	    S3C24XX_PA_UART
 #define S3C_PA_USBHOST	S3C2410_PA_USBHOST
 #define S3C_PA_HSMMC0	    S3C2443_PA_HSMMC
+#define S3C_PA_NAND	    S3C24XX_PA_NAND
 
 #endif /* __ASM_ARCH_MAP_H */

arch/arm/mach-s3c2410/include/mach/regs-gpio.h

@@ -328,13 +328,15 @@
 
 #define S3C2410_GPD8_VD16	(0x02 << 16)
 #define S3C2400_GPD8_TOUT3	(0x02 << 16)
+#define S3C2440_GPD8_SPIMISO1	(0x03 << 16)
 
 #define S3C2410_GPD9_VD17	(0x02 << 18)
 #define S3C2400_GPD9_TCLK0	(0x02 << 18)
-#define S3C2410_GPD9_MASK       (0x03 << 18)
+#define S3C2440_GPD9_SPIMOSI1	(0x03 << 18)
 
 #define S3C2410_GPD10_VD18	(0x02 << 20)
 #define S3C2400_GPD10_nWAIT	(0x02 << 20)
+#define S3C2440_GPD10_SPICLK1	(0x03 << 20)
 
 #define S3C2410_GPD11_VD19	(0x02 << 22)
 

arch/arm/mach-s3c2410/include/mach/regs-mem.h

@@ -73,6 +73,16 @@
 #define S3C2410_BWSCON_WS7		(1<<30)
 #define S3C2410_BWSCON_ST7		(1<<31)
 
+/* accesor functions for getting BANK(n) configuration. (n != 0) */
+
+#define S3C2410_BWSCON_GET(_bwscon, _bank) (((_bwscon) >> ((_bank) * 4)) & 0xf)
+
+#define S3C2410_BWSCON_DW8		(0)
+#define S3C2410_BWSCON_DW16		(1)
+#define S3C2410_BWSCON_DW32		(2)
+#define S3C2410_BWSCON_WS		(1 << 2)
+#define S3C2410_BWSCON_ST		(1 << 3)
+
 /* memory set (rom, ram) */
 #define S3C2410_BANKCON0		S3C2410_MEMREG(0x0004)
 #define S3C2410_BANKCON1		S3C2410_MEMREG(0x0008)

arch/arm/mach-s3c2410/include/mach/regs-s3c2412-mem.h

@@ -14,9 +14,11 @@
 #ifndef __ASM_ARM_REGS_S3C2412_MEM
 #define __ASM_ARM_REGS_S3C2412_MEM
 
-#ifndef S3C2412_MEMREG
 #define S3C2412_MEMREG(x) (S3C24XX_VA_MEMCTRL + (x))
-#endif
+#define S3C2412_EBIREG(x) (S3C2412_VA_EBI + (x))
+
+#define S3C2412_SSMCREG(x) (S3C2412_VA_SSMC + (x))
+#define S3C2412_SSMC(x, o) (S3C2412_SSMCREG((x * 0x20) + (o)))
 
 #define S3C2412_BANKCFG			S3C2412_MEMREG(0x00)
 #define S3C2412_BANKCON1		S3C2412_MEMREG(0x04)
@@ -26,4 +28,21 @@
 #define S3C2412_REFRESH			S3C2412_MEMREG(0x10)
 #define S3C2412_TIMEOUT			S3C2412_MEMREG(0x14)
 
+/* EBI control registers */
+
+#define S3C2412_EBI_PR			S3C2412_EBIREG(0x00)
+#define S3C2412_EBI_BANKCFG		S3C2412_EBIREG(0x04)
+
+/* SSMC control registers */
+
+#define S3C2412_SSMC_BANK(x)		S3C2412_SSMC(x, 0x00)
+#define S3C2412_SMIDCYR(x)		S3C2412_SSMC(x, 0x00)
+#define S3C2412_SMBWSTRD(x)		S3C2412_SSMC(x, 0x04)
+#define S3C2412_SMBWSTWRR(x)		S3C2412_SSMC(x, 0x08)
+#define S3C2412_SMBWSTOENR(x)		S3C2412_SSMC(x, 0x0C)
+#define S3C2412_SMBWSTWENR(x)		S3C2412_SSMC(x, 0x10)
+#define S3C2412_SMBCR(x)		S3C2412_SSMC(x, 0x14)
+#define S3C2412_SMBSR(x)		S3C2412_SSMC(x, 0x18)
+#define S3C2412_SMBWSTBRDR(x)		S3C2412_SSMC(x, 0x1C)
+
 #endif /*  __ASM_ARM_REGS_S3C2412_MEM */

arch/arm/mach-s3c2410/include/mach/spi.h

@@ -30,4 +30,7 @@ extern void s3c24xx_spi_gpiocfg_bus0_gpe11_12_13(struct s3c2410_spi_info *spi,
 extern void s3c24xx_spi_gpiocfg_bus1_gpg5_6_7(struct s3c2410_spi_info *spi,
 					      int enable);
 
+extern void s3c24xx_spi_gpiocfg_bus1_gpd8_9_10(struct s3c2410_spi_info *spi,
+					       int enable);
+
 #endif /* __ASM_ARCH_SPI_H */

arch/arm/mach-s3c2410/irq.c

@@ -39,9 +39,22 @@ static struct sysdev_driver s3c2410_irq_driver = {
 	.resume		= s3c24xx_irq_resume,
 };
 
-static int s3c2410_irq_init(void)
+static int __init s3c2410_irq_init(void)
 {
 	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_irq_driver);
 }
 
 arch_initcall(s3c2410_irq_init);
+
+static struct sysdev_driver s3c2410a_irq_driver = {
+	.add		= s3c2410_irq_add,
+	.suspend	= s3c24xx_irq_suspend,
+	.resume		= s3c24xx_irq_resume,
+};
+
+static int __init s3c2410a_irq_init(void)
+{
+	return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_irq_driver);
+}
+
+arch_initcall(s3c2410a_irq_init);

arch/arm/mach-s3c2410/mach-bast.c

@@ -45,6 +45,7 @@
 #include <mach/regs-mem.h>
 #include <mach/regs-lcd.h>
 
+#include <plat/hwmon.h>
 #include <plat/nand.h>
 #include <plat/iic.h>
 #include <mach/fb.h>
@@ -59,6 +60,7 @@
 #include <plat/clock.h>
 #include <plat/devs.h>
 #include <plat/cpu.h>
+#include <plat/cpu-freq.h>
 
 #include "usb-simtec.h"
 #include "nor-simtec.h"
@@ -547,7 +549,35 @@ static struct i2c_board_info bast_i2c_devs[] __initdata = {
 	},
 };
 
+static struct s3c_hwmon_pdata bast_hwmon_info = {
+	/* LCD contrast (0-6.6V) */
+	.in[0] = &(struct s3c_hwmon_chcfg) {
+		.name		= "lcd-contrast",
+		.mult		= 3300,
+		.div		= 512,
+	},
+	/* LED current feedback */
+	.in[1] = &(struct s3c_hwmon_chcfg) {
+		.name		= "led-feedback",
+		.mult		= 3300,
+		.div		= 1024,
+	},
+	/* LCD feedback (0-6.6V) */
+	.in[2] = &(struct s3c_hwmon_chcfg) {
+		.name		= "lcd-feedback",
+		.mult		= 3300,
+		.div		= 512,
+	},
+	/* Vcore (1.8-2.0V), Vref 3.3V  */
+	.in[3] = &(struct s3c_hwmon_chcfg) {
+		.name		= "vcore",
+		.mult		= 3300,
+		.div		= 1024,
+	},
+};
+
 /* Standard BAST devices */
+// cat /sys/devices/platform/s3c24xx-adc/s3c-hwmon/in_0
 
 static struct platform_device *bast_devices[] __initdata = {
 	&s3c_device_usb,
@@ -556,6 +586,8 @@ static struct platform_device *bast_devices[] __initdata = {
 	&s3c_device_i2c0,
  	&s3c_device_rtc,
 	&s3c_device_nand,
+	&s3c_device_adc,
+	&s3c_device_hwmon,
 	&bast_device_dm9k,
 	&bast_device_asix,
 	&bast_device_axpp,
@@ -570,6 +602,12 @@ static struct clk *bast_clocks[] __initdata = {
 	&s3c24xx_uclk,
 };
 
+static struct s3c_cpufreq_board __initdata bast_cpufreq = {
+	.refresh	= 7800, /* 7.8usec */
+	.auto_io	= 1,
+	.need_io	= 1,
+};
+
 static void __init bast_map_io(void)
 {
 	/* initialise the clocks */
@@ -588,6 +626,7 @@ static void __init bast_map_io(void)
 	s3c24xx_register_clocks(bast_clocks, ARRAY_SIZE(bast_clocks));
 
 	s3c_device_nand.dev.platform_data = &bast_nand_info;
+	s3c_device_hwmon.dev.platform_data = &bast_hwmon_info;
 
 	s3c24xx_init_io(bast_iodesc, ARRAY_SIZE(bast_iodesc));
 	s3c24xx_init_clocks(0);
@@ -608,6 +647,8 @@ static void __init bast_init(void)
 
 	usb_simtec_init();
 	nor_simtec_init();
+
+	s3c_cpufreq_setboard(&bast_cpufreq);
 }
 
 MACHINE_START(BAST, "Simtec-BAST")

arch/arm/mach-s3c2410/pll.c

+/* arch/arm/mach-s3c2410/pll.c
+ *
+ * Copyright (c) 2006,2007 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	Vincent Sanders <vince@arm.linux.org.uk>
+ *
+ * S3C2410 CPU PLL tables
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+*/
+
+#include <linux/types.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/sysdev.h>
+#include <linux/list.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+
+#include <plat/cpu.h>
+#include <plat/cpu-freq-core.h>
+
+static struct cpufreq_frequency_table pll_vals_12MHz[] = {
+    { .frequency = 34000000,  .index = PLLVAL(82, 2, 3),   },
+    { .frequency = 45000000,  .index = PLLVAL(82, 1, 3),   },
+    { .frequency = 51000000,  .index = PLLVAL(161, 3, 3),  },
+    { .frequency = 48000000,  .index = PLLVAL(120, 2, 3),  },
+    { .frequency = 56000000,  .index = PLLVAL(142, 2, 3),  },
+    { .frequency = 68000000,  .index = PLLVAL(82, 2, 2),   },
+    { .frequency = 79000000,  .index = PLLVAL(71, 1, 2),   },
+    { .frequency = 85000000,  .index = PLLVAL(105, 2, 2),  },
+    { .frequency = 90000000,  .index = PLLVAL(112, 2, 2),  },
+    { .frequency = 101000000, .index = PLLVAL(127, 2, 2),  },
+    { .frequency = 113000000, .index = PLLVAL(105, 1, 2),  },
+    { .frequency = 118000000, .index = PLLVAL(150, 2, 2),  },
+    { .frequency = 124000000, .index = PLLVAL(116, 1, 2),  },
+    { .frequency = 135000000, .index = PLLVAL(82, 2, 1),   },
+    { .frequency = 147000000, .index = PLLVAL(90, 2, 1),   },
+    { .frequency = 152000000, .index = PLLVAL(68, 1, 1),   },
+    { .frequency = 158000000, .index = PLLVAL(71, 1, 1),   },
+    { .frequency = 170000000, .index = PLLVAL(77, 1, 1),   },
+    { .frequency = 180000000, .index = PLLVAL(82, 1, 1),   },
+    { .frequency = 186000000, .index = PLLVAL(85, 1, 1),   },
+    { .frequency = 192000000, .index = PLLVAL(88, 1, 1),   },
+    { .frequency = 203000000, .index = PLLVAL(161, 3, 1),  },
+
+    /* 2410A extras */
+
+    { .frequency = 210000000, .index = PLLVAL(132, 2, 1),  },
+    { .frequency = 226000000, .index = PLLVAL(105, 1, 1),  },
+    { .frequency = 266000000, .index = PLLVAL(125, 1, 1),  },
+    { .frequency = 268000000, .index = PLLVAL(126, 1, 1),  },
+    { .frequency = 270000000, .index = PLLVAL(127, 1, 1),  },
+};
+
+static int s3c2410_plls_add(struct sys_device *dev)
+{
+	return s3c_plltab_register(pll_vals_12MHz, ARRAY_SIZE(pll_vals_12MHz));
+}
+
+static struct sysdev_driver s3c2410_plls_drv = {
+	.add	= s3c2410_plls_add,
+};
+
+static int __init s3c2410_pll_init(void)
+{
+	return sysdev_driver_register(&s3c2410_sysclass, &s3c2410_plls_drv);
+
+}
+
+arch_initcall(s3c2410_pll_init);
+
+static struct sysdev_driver s3c2410a_plls_drv = {
+	.add	= s3c2410_plls_add,
+};
+
+static int __init s3c2410a_pll_init(void)
+{
+	return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_plls_drv);
+}
+
+arch_initcall(s3c2410a_pll_init);

arch/arm/mach-s3c2410/pm.c

@@ -119,6 +119,18 @@ static int __init s3c2410_pm_drvinit(void)
 }
 
 arch_initcall(s3c2410_pm_drvinit);
+
+static struct sysdev_driver s3c2410a_pm_driver = {
+	.add		= s3c2410_pm_add,
+	.resume		= s3c2410_pm_resume,
+};
+
+static int __init s3c2410a_pm_drvinit(void)
+{
+	return sysdev_driver_register(&s3c2410a_sysclass, &s3c2410a_pm_driver);
+}
+
+arch_initcall(s3c2410a_pm_drvinit);
 #endif
 
 #if defined(CONFIG_CPU_S3C2440)

arch/arm/mach-s3c2410/s3c2410.c

@@ -105,17 +105,33 @@ void __init_or_cpufreq s3c2410_setup_clocks(void)
 	s3c24xx_setup_clocks(fclk, hclk, pclk);
 }
 
+/* fake ARMCLK for use with cpufreq, etc. */
+
+static struct clk s3c2410_armclk = {
+	.name	= "armclk",
+	.parent	= &clk_f,
+	.id	= -1,
+};
+
 void __init s3c2410_init_clocks(int xtal)
 {
 	s3c24xx_register_baseclocks(xtal);
 	s3c2410_setup_clocks();
 	s3c2410_baseclk_add();
+	s3c24xx_register_clock(&s3c2410_armclk);
 }
 
 struct sysdev_class s3c2410_sysclass = {
 	.name = "s3c2410-core",
 };
 
+/* Note, we would have liked to name this s3c2410-core, but we cannot
+ * register two sysdev_class with the same name.
+ */
+struct sysdev_class s3c2410a_sysclass = {
+	.name = "s3c2410a-core",
+};
+
 static struct sys_device s3c2410_sysdev = {
 	.cls		= &s3c2410_sysclass,
 };
@@ -133,9 +149,22 @@ static int __init s3c2410_core_init(void)
 
 core_initcall(s3c2410_core_init);
 
+static int __init s3c2410a_core_init(void)
+{
+	return sysdev_class_register(&s3c2410a_sysclass);
+}
+
+core_initcall(s3c2410a_core_init);
+
 int __init s3c2410_init(void)
 {
 	printk("S3C2410: Initialising architecture\n");
 
 	return sysdev_register(&s3c2410_sysdev);
 }
+
+int __init s3c2410a_init(void)
+{
+	s3c2410_sysdev.cls = &s3c2410a_sysclass;
+	return s3c2410_init();
+}

arch/arm/mach-s3c2412/Kconfig

@@ -32,6 +32,15 @@ config S3C2412_PM
 	help
 	  Internal config node to apply S3C2412 power management
 
+# Note, the S3C2412 IOtiming support is in plat-s3c24xx
+
+config S3C2412_CPUFREQ
+	bool
+	depends on CPU_FREQ_S3C24XX && CPU_S3C2412
+	select S3C2412_IOTIMING
+	default y
+	help
+	  CPU Frequency scaling support for S3C2412 and S3C2413 SoC CPUs.
 
 menu "S3C2412 Machines"
 

arch/arm/mach-s3c2412/Makefile

@@ -15,6 +15,7 @@ obj-$(CONFIG_CPU_S3C2412)	+= clock.o
 obj-$(CONFIG_CPU_S3C2412)	+= gpio.o
 obj-$(CONFIG_S3C2412_DMA)	+= dma.o
 obj-$(CONFIG_S3C2412_PM)	+= pm.o sleep.o
+obj-$(CONFIG_S3C2412_CPUFREQ)	+= cpu-freq.o
 
 # Machine support
 

arch/arm/mach-s3c2412/cpu-freq.c

+/* linux/arch/arm/mach-s3c2412/cpu-freq.c
+ *
+ * Copyright 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C2412 CPU Frequency scalling
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#include <linux/sysdev.h>
+#include <linux/delay.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/regs-clock.h>
+#include <mach/regs-s3c2412-mem.h>
+
+#include <plat/cpu.h>
+#include <plat/clock.h>
+#include <plat/cpu-freq-core.h>
+
+/* our clock resources. */
+static struct clk *xtal;
+static struct clk *fclk;
+static struct clk *hclk;
+static struct clk *armclk;
+
+/* HDIV: 1, 2, 3, 4, 6, 8 */
+
+static int s3c2412_cpufreq_calcdivs(struct s3c_cpufreq_config *cfg)
+{
+	unsigned int hdiv, pdiv, armdiv, dvs;
+	unsigned long hclk, fclk, armclk, armdiv_clk;
+	unsigned long hclk_max;
+
+	fclk = cfg->freq.fclk;
+	armclk = cfg->freq.armclk;
+	hclk_max = cfg->max.hclk;
+
+	/* We can't run hclk above armclk as at the best we have to
+	 * have armclk and hclk in dvs mode. */
+
+	if (hclk_max > armclk)
+		hclk_max = armclk;
+
+	s3c_freq_dbg("%s: fclk=%lu, armclk=%lu, hclk_max=%lu\n",
+		     __func__, fclk, armclk, hclk_max);
+	s3c_freq_dbg("%s: want f=%lu, arm=%lu, h=%lu, p=%lu\n",
+		     __func__, cfg->freq.fclk, cfg->freq.armclk,
+		     cfg->freq.hclk, cfg->freq.pclk);
+
+	armdiv = fclk / armclk;
+
+	if (armdiv < 1)
+		armdiv = 1;
+	if (armdiv > 2)
+		armdiv = 2;
+
+	cfg->divs.arm_divisor = armdiv;
+	armdiv_clk = fclk / armdiv;
+
+	hdiv = armdiv_clk / hclk_max;
+	if (hdiv < 1)
+		hdiv = 1;
+
+	cfg->freq.hclk = hclk = armdiv_clk / hdiv;
+
+	/* set dvs depending on whether we reached armclk or not. */
+	cfg->divs.dvs = dvs = armclk < armdiv_clk;
+
+	/* update the actual armclk we achieved. */
+	cfg->freq.armclk = dvs ? hclk : armdiv_clk;
+
+	s3c_freq_dbg("%s: armclk %lu, hclk %lu, armdiv %d, hdiv %d, dvs %d\n",
+		     __func__, armclk, hclk, armdiv, hdiv, cfg->divs.dvs);
+
+	if (hdiv > 4)
+		goto invalid;
+
+	pdiv = (hclk > cfg->max.pclk) ? 2 : 1;
+
+	if ((hclk / pdiv) > cfg->max.pclk)
+		pdiv++;
+
+	cfg->freq.pclk = hclk / pdiv;
+
+	s3c_freq_dbg("%s: pdiv %d\n", __func__, pdiv);
+
+	if (pdiv > 2)
+		goto invalid;
+
+	pdiv *= hdiv;
+
+	/* store the result, and then return */
+
+	cfg->divs.h_divisor = hdiv * armdiv;
+	cfg->divs.p_divisor = pdiv * armdiv;
+
+	return 0;
+
+ invalid:
+	return -EINVAL;
+}
+
+static void s3c2412_cpufreq_setdivs(struct s3c_cpufreq_config *cfg)
+{
+	unsigned long clkdiv;
+	unsigned long olddiv;
+
+	olddiv = clkdiv = __raw_readl(S3C2410_CLKDIVN);
+
+	/* clear off current clock info */
+
+	clkdiv &= ~S3C2412_CLKDIVN_ARMDIVN;
+	clkdiv &= ~S3C2412_CLKDIVN_HDIVN_MASK;
+	clkdiv &= ~S3C2412_CLKDIVN_PDIVN;
+
+	if (cfg->divs.arm_divisor == 2)
+		clkdiv |= S3C2412_CLKDIVN_ARMDIVN;
+
+	clkdiv |= ((cfg->divs.h_divisor / cfg->divs.arm_divisor) - 1);
+
+	if (cfg->divs.p_divisor != cfg->divs.h_divisor)
+		clkdiv |= S3C2412_CLKDIVN_PDIVN;
+
+	s3c_freq_dbg("%s: div %08lx => %08lx\n", __func__, olddiv, clkdiv);
+	__raw_writel(clkdiv, S3C2410_CLKDIVN);
+
+	clk_set_parent(armclk, cfg->divs.dvs ? hclk : fclk);
+}
+
+static void s3c2412_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg)
+{
+	struct s3c_cpufreq_board *board = cfg->board;
+	unsigned long refresh;
+
+	s3c_freq_dbg("%s: refresh %u ns, hclk %lu\n", __func__,
+		     board->refresh, cfg->freq.hclk);
+
+	/* Reduce both the refresh time (in ns) and the frequency (in MHz)
+	 * by 10 each to ensure that we do not overflow 32 bit numbers. This
+	 * should work for HCLK up to 133MHz and refresh period up to 30usec.
+	 */
+
+	refresh = (board->refresh / 10);
+	refresh *= (cfg->freq.hclk / 100);
+	refresh /= (1 * 1000 * 1000);	/* 10^6 */
+
+	s3c_freq_dbg("%s: setting refresh 0x%08lx\n", __func__, refresh);
+	__raw_writel(refresh, S3C2412_REFRESH);
+}
+
+/* set the default cpu frequency information, based on an 200MHz part
+ * as we have no other way of detecting the speed rating in software.
+ */
+
+static struct s3c_cpufreq_info s3c2412_cpufreq_info = {
+	.max		= {
+		.fclk	= 200000000,
+		.hclk	= 100000000,
+		.pclk	=  50000000,
+	},
+
+	.latency	= 5000000, /* 5ms */
+
+	.locktime_m	= 150,
+	.locktime_u	= 150,
+	.locktime_bits	= 16,
+
+	.name		= "s3c2412",
+	.set_refresh	= s3c2412_cpufreq_setrefresh,
+	.set_divs	= s3c2412_cpufreq_setdivs,
+	.calc_divs	= s3c2412_cpufreq_calcdivs,
+
+	.calc_iotiming	= s3c2412_iotiming_calc,
+	.set_iotiming	= s3c2412_iotiming_set,
+	.get_iotiming	= s3c2412_iotiming_get,
+
+	.resume_clocks	= s3c2412_setup_clocks,
+
+	.debug_io_show  = s3c_cpufreq_debugfs_call(s3c2412_iotiming_debugfs),
+};
+
+static int s3c2412_cpufreq_add(struct sys_device *sysdev)
+{
+	unsigned long fclk_rate;
+
+	hclk = clk_get(NULL, "hclk");
+	if (IS_ERR(hclk)) {
+		printk(KERN_ERR "%s: cannot find hclk clock\n", __func__);
+		return -ENOENT;
+	}
+
+	fclk = clk_get(NULL, "fclk");
+	if (IS_ERR(fclk)) {
+		printk(KERN_ERR "%s: cannot find fclk clock\n", __func__);
+		goto err_fclk;
+	}
+
+	fclk_rate = clk_get_rate(fclk);
+	if (fclk_rate > 200000000) {
+		printk(KERN_INFO
+		       "%s: fclk %ld MHz, assuming 266MHz capable part\n",
+		       __func__, fclk_rate / 1000000);
+		s3c2412_cpufreq_info.max.fclk = 266000000;
+		s3c2412_cpufreq_info.max.hclk = 133000000;
+		s3c2412_cpufreq_info.max.pclk =  66000000;
+	}
+
+	armclk = clk_get(NULL, "armclk");
+	if (IS_ERR(armclk)) {
+		printk(KERN_ERR "%s: cannot find arm clock\n", __func__);
+		goto err_armclk;
+	}
+
+	xtal = clk_get(NULL, "xtal");
+	if (IS_ERR(xtal)) {
+		printk(KERN_ERR "%s: cannot find xtal clock\n", __func__);
+		goto err_xtal;
+	}
+
+	return s3c_cpufreq_register(&s3c2412_cpufreq_info);
+
+err_xtal:
+	clk_put(armclk);
+err_armclk:
+	clk_put(fclk);
+err_fclk:
+	clk_put(hclk);
+
+	return -ENOENT;
+}
+
+static struct sysdev_driver s3c2412_cpufreq_driver = {
+	.add		= s3c2412_cpufreq_add,
+};
+
+static int s3c2412_cpufreq_init(void)
+{
+	return sysdev_driver_register(&s3c2412_sysclass,
+				      &s3c2412_cpufreq_driver);
+}
+
+arch_initcall(s3c2412_cpufreq_init);

arch/arm/mach-s3c2412/s3c2412.c

@@ -69,6 +69,18 @@ static struct map_desc s3c2412_iodesc[] __initdata = {
 	IODESC_ENT(CLKPWR),
 	IODESC_ENT(TIMER),
 	IODESC_ENT(WATCHDOG),
+	{
+		.virtual = (unsigned long)S3C2412_VA_SSMC,
+		.pfn	 = __phys_to_pfn(S3C2412_PA_SSMC),
+		.length	 = SZ_1M,
+		.type	 = MT_DEVICE,
+	},
+	{
+		.virtual = (unsigned long)S3C2412_VA_EBI,
+		.pfn	 = __phys_to_pfn(S3C2412_PA_EBI),
+		.length	 = SZ_1M,
+		.type	 = MT_DEVICE,
+	},
 };
 
 /* uart registration process */

arch/arm/mach-s3c2440/Kconfig

@@ -33,6 +33,7 @@ config MACH_ANUBIS
 	select PM_SIMTEC if PM
 	select HAVE_PATA_PLATFORM
 	select S3C24XX_GPIO_EXTRA64
+	select S3C2440_XTAL_12000000
 	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Simtec Electronics ANUBIS
@@ -44,6 +45,8 @@ config MACH_OSIRIS
 	select S3C24XX_DCLK
 	select PM_SIMTEC if PM
 	select S3C24XX_GPIO_EXTRA128
+	select S3C2440_XTAL_12000000
+	select S3C2410_IOTIMING if S3C2440_CPUFREQ
 	select S3C_DEV_USB_HOST
 	help
 	  Say Y here if you are using the Simtec IM2440D20 module, also
@@ -52,6 +55,7 @@ config MACH_OSIRIS
 config MACH_RX3715
 	bool "HP iPAQ rx3715"
 	select CPU_S3C2440
+	select S3C2440_XTAL_16934400
 	select PM_H1940 if PM
 	help
 	  Say Y here if you are using the HP iPAQ rx3715.
@@ -59,6 +63,7 @@ config MACH_RX3715
 config ARCH_S3C2440
 	bool "SMDK2440"
 	select CPU_S3C2440
+	select S3C2440_XTAL_16934400
 	select MACH_SMDK
 	select S3C_DEV_USB_HOST
 	help
@@ -67,6 +72,7 @@ config ARCH_S3C2440
 config MACH_NEXCODER_2440
  	bool "NexVision NEXCODER 2440 Light Board"
  	select CPU_S3C2440
+	select S3C2440_XTAL_12000000
 	select S3C_DEV_USB_HOST
 	help
  	  Say Y here if you are using the Nex Vision NEXCODER 2440 Light Board
@@ -75,6 +81,7 @@ config SMDK2440_CPU2440
 	bool "SMDK2440 with S3C2440 CPU module"
 	depends on ARCH_S3C2440
 	default y if ARCH_S3C2440
+	select S3C2440_XTAL_16934400
 	select CPU_S3C2440
 
 config MACH_AT2440EVB

arch/arm/mach-s3c2440/mach-osiris.c

@@ -34,6 +34,7 @@
 #include <asm/irq.h>
 #include <asm/mach-types.h>
 
+#include <plat/cpu-freq.h>
 #include <plat/regs-serial.h>
 #include <mach/regs-gpio.h>
 #include <mach/regs-mem.h>
@@ -351,6 +352,12 @@ static struct clk *osiris_clocks[] __initdata = {
 	&s3c24xx_uclk,
 };
 
+static struct s3c_cpufreq_board __initdata osiris_cpufreq = {
+	.refresh	= 7800, /* refresh period is 7.8usec */
+	.auto_io	= 1,
+	.need_io	= 1,
+};
+
 static void __init osiris_map_io(void)
 {
 	unsigned long flags;
@@ -402,6 +409,8 @@ static void __init osiris_init(void)
 
 	s3c_i2c0_set_platdata(NULL);
 
+	s3c_cpufreq_setboard(&osiris_cpufreq);
+
 	i2c_register_board_info(0, osiris_i2c_devs,
 				ARRAY_SIZE(osiris_i2c_devs));
 

arch/arm/mach-s3c24a0/include/mach/map.h

@@ -81,5 +81,6 @@
 
 #define S3C_PA_UART		S3C24A0_PA_UART
 #define S3C_PA_IIC		S3C24A0_PA_IIC
+#define S3C_PA_NAND		S3C24XX_PA_NAND
 
 #endif /* __ASM_ARCH_24A0_MAP_H */

arch/arm/mach-s3c6400/include/mach/map.h

@@ -38,18 +38,21 @@
 #define S3C_VA_UART2		S3C_VA_UARTx(2)
 #define S3C_VA_UART3		S3C_VA_UARTx(3)
 
+#define S3C64XX_PA_NAND		(0x70200000)
 #define S3C64XX_PA_FB		(0x77100000)
 #define S3C64XX_PA_USB_HSOTG	(0x7C000000)
 #define S3C64XX_PA_WATCHDOG	(0x7E004000)
 #define S3C64XX_PA_SYSCON	(0x7E00F000)
+#define S3C64XX_PA_AC97		(0x7F001000)
 #define S3C64XX_PA_IIS0		(0x7F002000)
 #define S3C64XX_PA_IIS1		(0x7F003000)
 #define S3C64XX_PA_TIMER	(0x7F006000)
 #define S3C64XX_PA_IIC0		(0x7F004000)
+#define S3C64XX_PA_IISV4	(0x7F00D000)
 #define S3C64XX_PA_IIC1		(0x7F00F000)
 
 #define S3C64XX_PA_GPIO		(0x7F008000)
-#define S3C64XX_VA_GPIO		S3C_ADDR(0x00500000)
+#define S3C64XX_VA_GPIO		S3C_ADDR_CPU(0x00000000)
 #define S3C64XX_SZ_GPIO		SZ_4K
 
 #define S3C64XX_PA_SDRAM	(0x50000000)
@@ -57,7 +60,7 @@
 #define S3C64XX_PA_VIC1		(0x71300000)
 
 #define S3C64XX_PA_MODEM	(0x74108000)
-#define S3C64XX_VA_MODEM	S3C_ADDR(0x00600000)
+#define S3C64XX_VA_MODEM	S3C_ADDR_CPU(0x00100000)
 
 #define S3C64XX_PA_USBHOST	(0x74300000)
 
@@ -72,6 +75,7 @@
 #define S3C_PA_HSMMC2		S3C64XX_PA_HSMMC2
 #define S3C_PA_IIC		S3C64XX_PA_IIC0
 #define S3C_PA_IIC1		S3C64XX_PA_IIC1
+#define S3C_PA_NAND		S3C64XX_PA_NAND
 #define S3C_PA_FB		S3C64XX_PA_FB
 #define S3C_PA_USBHOST		S3C64XX_PA_USBHOST
 #define S3C_PA_USB_HSOTG	S3C64XX_PA_USB_HSOTG

arch/arm/mach-s3c6400/s3c6400.c

@@ -48,6 +48,8 @@ void __init s3c6400_map_io(void)
 
 	/* the i2c devices are directly compatible with s3c2440 */
 	s3c_i2c0_setname("s3c2440-i2c");
+
+	s3c_device_nand.name = "s3c6400-nand";
 }
 
 void __init s3c6400_init_clocks(int xtal)

arch/arm/mach-s3c6410/Kconfig

@@ -97,3 +97,13 @@ config MACH_NCP
 	select S3C64XX_SETUP_I2C1
 	help
           Machine support for the Samsung NCP
+
+config MACH_HMT
+	bool "Airgoo HMT"
+	select CPU_S3C6410
+	select S3C_DEV_FB
+	select S3C_DEV_USB_HOST
+	select S3C64XX_SETUP_FB_24BPP
+	select HAVE_PWM
+	help
+	  Machine support for the Airgoo HMT

arch/arm/mach-s3c6410/Makefile

@@ -23,5 +23,4 @@ obj-$(CONFIG_S3C6410_SETUP_SDHCI)	+= setup-sdhci.o
 obj-$(CONFIG_MACH_ANW6410)	+= mach-anw6410.o
 obj-$(CONFIG_MACH_SMDK6410)	+= mach-smdk6410.o
 obj-$(CONFIG_MACH_NCP)		+= mach-ncp.o
-
-
+obj-$(CONFIG_MACH_HMT)		+= mach-hmt.o

arch/arm/mach-s3c6410/cpu.c

@@ -62,6 +62,8 @@ void __init s3c6410_map_io(void)
 	/* the i2c devices are directly compatible with s3c2440 */
 	s3c_i2c0_setname("s3c2440-i2c");
 	s3c_i2c1_setname("s3c2440-i2c");
+
+	s3c_device_nand.name = "s3c6400-nand";
 }
 
 void __init s3c6410_init_clocks(int xtal)

arch/arm/mach-s3c6410/mach-hmt.c

+/* mach-hmt.c - Platform code for Airgoo HMT
+ *
+ * Copyright 2009 Peter Korsgaard <jacmet@sunsite.dk>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/gpio.h>
+#include <linux/delay.h>
+#include <linux/leds.h>
+#include <linux/pwm_backlight.h>
+#include <linux/mtd/mtd.h>
+#include <linux/mtd/partitions.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/regs-fb.h>
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+#include <plat/iic.h>
+#include <plat/fb.h>
+#include <plat/nand.h>
+
+#include <plat/s3c6410.h>
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+
+#define UCON S3C2410_UCON_DEFAULT
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE)
+#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
+
+static struct s3c2410_uartcfg hmt_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+};
+
+static int hmt_bl_init(struct device *dev)
+{
+	int ret;
+
+	ret = gpio_request(S3C64XX_GPB(4), "lcd backlight enable");
+	if (!ret)
+		ret = gpio_direction_output(S3C64XX_GPB(4), 0);
+
+	return ret;
+}
+
+static int hmt_bl_notify(int brightness)
+{
+	/*
+	 * translate from CIELUV/CIELAB L*->brightness, E.G. from
+	 * perceived luminance to light output. Assumes range 0..25600
+	 */
+	if (brightness < 0x800) {
+		/* Y = Yn * L / 903.3 */
+		brightness = (100*256 * brightness + 231245/2) / 231245;
+	} else {
+		/* Y = Yn * ((L + 16) / 116 )^3 */
+		int t = (brightness*4 + 16*1024 + 58)/116;
+		brightness = 25 * ((t * t * t + 0x100000/2) / 0x100000);
+	}
+
+	gpio_set_value(S3C64XX_GPB(4), brightness);
+
+	return brightness;
+}
+
+static void hmt_bl_exit(struct device *dev)
+{
+	gpio_free(S3C64XX_GPB(4));
+}
+
+static struct platform_pwm_backlight_data hmt_backlight_data = {
+	.pwm_id		= 1,
+	.max_brightness	= 100 * 256,
+	.dft_brightness	= 40 * 256,
+	.pwm_period_ns	= 1000000000 / (100 * 256 * 20),
+	.init		= hmt_bl_init,
+	.notify		= hmt_bl_notify,
+	.exit		= hmt_bl_exit,
+
+};
+
+static struct platform_device hmt_backlight_device = {
+	.name		= "pwm-backlight",
+	.dev		= {
+		.parent	= &s3c_device_timer[1].dev,
+		.platform_data = &hmt_backlight_data,
+	},
+};
+
+static struct s3c_fb_pd_win hmt_fb_win0 = {
+	.win_mode	= {
+		.pixclock	= 41094,
+		.left_margin	= 8,
+		.right_margin	= 13,
+		.upper_margin	= 7,
+		.lower_margin	= 5,
+		.hsync_len	= 3,
+		.vsync_len	= 1,
+		.xres		= 800,
+		.yres		= 480,
+	},
+	.max_bpp	= 32,
+	.default_bpp	= 16,
+};
+
+/* 405566 clocks per frame => 60Hz refresh requires 24333960Hz clock */
+static struct s3c_fb_platdata hmt_lcd_pdata __initdata = {
+	.setup_gpio	= s3c64xx_fb_gpio_setup_24bpp,
+	.win[0]		= &hmt_fb_win0,
+	.vidcon0	= VIDCON0_VIDOUT_RGB | VIDCON0_PNRMODE_RGB,
+	.vidcon1	= VIDCON1_INV_HSYNC | VIDCON1_INV_VSYNC,
+};
+
+static struct mtd_partition hmt_nand_part[] = {
+	[0] = {
+		.name	= "uboot",
+		.size	= SZ_512K,
+		.offset	= 0,
+	},
+	[1] = {
+		.name	= "uboot-env1",
+		.size	= SZ_256K,
+		.offset	= SZ_512K,
+	},
+	[2] = {
+		.name	= "uboot-env2",
+		.size	= SZ_256K,
+		.offset	= SZ_512K + SZ_256K,
+	},
+	[3] = {
+		.name	= "kernel",
+		.size	= SZ_2M,
+		.offset	= SZ_1M,
+	},
+	[4] = {
+		.name	= "rootfs",
+		.size	= MTDPART_SIZ_FULL,
+		.offset	= SZ_1M + SZ_2M,
+	},
+};
+
+static struct s3c2410_nand_set hmt_nand_sets[] = {
+	[0] = {
+		.name		= "nand",
+		.nr_chips	= 1,
+		.nr_partitions	= ARRAY_SIZE(hmt_nand_part),
+		.partitions	= hmt_nand_part,
+	},
+};
+
+static struct s3c2410_platform_nand hmt_nand_info = {
+	.tacls		= 25,
+	.twrph0		= 55,
+	.twrph1		= 40,
+	.nr_sets	= ARRAY_SIZE(hmt_nand_sets),
+	.sets		= hmt_nand_sets,
+};
+
+static struct gpio_led hmt_leds[] = {
+	{ /* left function keys */
+		.name			= "left:blue",
+		.gpio			= S3C64XX_GPO(12),
+		.default_trigger	= "default-on",
+	},
+	{ /* right function keys - red */
+		.name			= "right:red",
+		.gpio			= S3C64XX_GPO(13),
+	},
+	{ /* right function keys - green */
+		.name			= "right:green",
+		.gpio			= S3C64XX_GPO(14),
+	},
+	{ /* right function keys - blue */
+		.name			= "right:blue",
+		.gpio			= S3C64XX_GPO(15),
+		.default_trigger	= "default-on",
+	},
+};
+
+static struct gpio_led_platform_data hmt_led_data = {
+	.num_leds = ARRAY_SIZE(hmt_leds),
+	.leds = hmt_leds,
+};
+
+static struct platform_device hmt_leds_device = {
+	.name			= "leds-gpio",
+	.id			= -1,
+	.dev.platform_data	= &hmt_led_data,
+};
+
+static struct map_desc hmt_iodesc[] = {};
+
+static struct platform_device *hmt_devices[] __initdata = {
+	&s3c_device_i2c0,
+	&s3c_device_nand,
+	&s3c_device_fb,
+	&s3c_device_usb,
+	&s3c_device_timer[1],
+	&hmt_backlight_device,
+	&hmt_leds_device,
+};
+
+static void __init hmt_map_io(void)
+{
+	s3c64xx_init_io(hmt_iodesc, ARRAY_SIZE(hmt_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(hmt_uartcfgs, ARRAY_SIZE(hmt_uartcfgs));
+}
+
+static void __init hmt_machine_init(void)
+{
+	s3c_i2c0_set_platdata(NULL);
+	s3c_fb_set_platdata(&hmt_lcd_pdata);
+	s3c_device_nand.dev.platform_data = &hmt_nand_info;
+
+	gpio_request(S3C64XX_GPC(7), "usb power");
+	gpio_direction_output(S3C64XX_GPC(7), 0);
+	gpio_request(S3C64XX_GPM(0), "usb power");
+	gpio_direction_output(S3C64XX_GPM(0), 1);
+	gpio_request(S3C64XX_GPK(7), "usb power");
+	gpio_direction_output(S3C64XX_GPK(7), 1);
+	gpio_request(S3C64XX_GPF(13), "usb power");
+	gpio_direction_output(S3C64XX_GPF(13), 1);
+
+	platform_add_devices(hmt_devices, ARRAY_SIZE(hmt_devices));
+}
+
+MACHINE_START(HMT, "Airgoo-HMT")
+	/* Maintainer: Peter Korsgaard <jacmet@sunsite.dk> */
+	.phys_io	= S3C_PA_UART & 0xfff00000,
+	.io_pg_offst	= (((u32)S3C_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S3C64XX_PA_SDRAM + 0x100,
+	.init_irq	= s3c6410_init_irq,
+	.map_io		= hmt_map_io,
+	.init_machine	= hmt_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/mach-s3c6410/mach-ncp.c

@@ -79,7 +79,7 @@ static struct platform_device *ncp_devices[] __initdata = {
 	&s3c_device_i2c0,
 };
 
-struct map_desc ncp_iodesc[] = {};
+static struct map_desc ncp_iodesc[] __initdata = {};
 
 static void __init ncp_map_io(void)
 {

arch/arm/mach-s3c6410/mach-smdk6410.c

@@ -65,16 +65,30 @@ static struct s3c2410_uartcfg smdk6410_uartcfgs[] __initdata = {
 	[0] = {
 		.hwport	     = 0,
 		.flags	     = 0,
-		.ucon	     = 0x3c5,
-		.ulcon	     = 0x03,
-		.ufcon	     = 0x51,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
 	},
 	[1] = {
 		.hwport	     = 1,
 		.flags	     = 0,
-		.ucon	     = 0x3c5,
-		.ulcon	     = 0x03,
-		.ufcon	     = 0x51,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
+	},
+	[3] = {
+		.hwport	     = 3,
+		.flags	     = 0,
+		.ucon	     = UCON,
+		.ulcon	     = ULCON,
+		.ufcon	     = UFCON,
 	},
 };
 

arch/arm/mach-s5pc100/Kconfig

+# arch/arm/mach-s5pc100/Kconfig
+#
+# Copyright 2009 Samsung Electronics Co.
+#	Byungho Min <bhmin@samsung.com>
+#
+# Licensed under GPLv2
+
+# Configuration options for the S5PC100 CPU
+
+config CPU_S5PC100
+	bool
+	select CPU_S5PC100_INIT
+	select CPU_S5PC100_CLOCK
+	help
+	  Enable S5PC100 CPU support
+
+config MACH_SMDKC100
+	bool "SMDKC100"
+	select CPU_S5PC100
+	select S5PC1XX_SETUP_I2C1
+	help
+	  Machine support for the Samsung SMDKC100

arch/arm/mach-s5pc100/Makefile

+# arch/arm/mach-s5pc100/Makefile
+#
+# Copyright 2009 Samsung Electronics Co.
+#
+# Licensed under GPLv2
+
+obj-y				:=
+obj-m				:=
+obj-n				:=
+obj-				:=
+
+# Core support for S5PC100 system
+
+obj-$(CONFIG_CPU_S5PC100)	+= cpu.o
+
+# machine support
+obj-$(CONFIG_MACH_SMDKC100)	+= mach-smdkc100.o

arch/arm/mach-s5pc100/Makefile.boot

+   zreladdr-y	:= 0x20008000
+params_phys-y	:= 0x20000100

arch/arm/mach-s5pc100/cpu.c

+/* linux/arch/arm/mach-s5pc100/cpu.c
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * Based on mach-s3c6410/cpu.c
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/clk.h>
+#include <linux/io.h>
+#include <linux/sysdev.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+#include <asm/mach/irq.h>
+
+#include <mach/hardware.h>
+#include <mach/map.h>
+#include <asm/irq.h>
+
+#include <plat/cpu-freq.h>
+#include <plat/regs-serial.h>
+
+#include <plat/cpu.h>
+#include <plat/devs.h>
+#include <plat/clock.h>
+#include <plat/sdhci.h>
+#include <plat/iic-core.h>
+#include <plat/s5pc100.h>
+
+/* Initial IO mappings */
+
+static struct map_desc s5pc100_iodesc[] __initdata = {
+};
+
+/* s5pc100_map_io
+ *
+ * register the standard cpu IO areas
+*/
+
+void __init s5pc100_map_io(void)
+{
+	iotable_init(s5pc100_iodesc, ARRAY_SIZE(s5pc100_iodesc));
+
+	/* initialise device information early */
+}
+
+void __init s5pc100_init_clocks(int xtal)
+{
+	printk(KERN_DEBUG "%s: initialising clocks\n", __func__);
+	s3c24xx_register_baseclocks(xtal);
+	s5pc1xx_register_clocks();
+	s5pc100_register_clocks();
+	s5pc100_setup_clocks();
+}
+
+void __init s5pc100_init_irq(void)
+{
+	u32 vic_valid[] = {~0, ~0, ~0};
+
+	/* VIC0, VIC1, and VIC2 are fully populated. */
+	s5pc1xx_init_irq(vic_valid, ARRAY_SIZE(vic_valid));
+}
+
+struct sysdev_class s5pc100_sysclass = {
+	.name	= "s5pc100-core",
+};
+
+static struct sys_device s5pc100_sysdev = {
+	.cls	= &s5pc100_sysclass,
+};
+
+static int __init s5pc100_core_init(void)
+{
+	return sysdev_class_register(&s5pc100_sysclass);
+}
+
+core_initcall(s5pc100_core_init);
+
+int __init s5pc100_init(void)
+{
+	printk(KERN_DEBUG "S5PC100: Initialising architecture\n");
+
+	return sysdev_register(&s5pc100_sysdev);
+}

arch/arm/mach-s5pc100/include/mach/debug-macro.S

+/* arch/arm/mach-s5pc100/include/mach/debug-macro.S
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ *
+ * Based on mach-s3c6400/include/mach/debug-macro.S
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+/* pull in the relevant register and map files. */
+
+#include <mach/map.h>
+#include <plat/regs-serial.h>
+
+	/* note, for the boot process to work we have to keep the UART
+	 * virtual address aligned to an 1MiB boundary for the L1
+	 * mapping the head code makes. We keep the UART virtual address
+	 * aligned and add in the offset when we load the value here.
+	 */
+
+	.macro addruart, rx
+		mrc	p15, 0, \rx, c1, c0
+		tst	\rx, #1
+		ldreq	\rx, = S3C_PA_UART
+		ldrne	\rx, = (S3C_VA_UART + S3C_PA_UART & 0xfffff)
+		add	\rx, \rx, #(0x400 * CONFIG_DEBUG_S3C_UART)
+	.endm
+
+/* include the reset of the code which will do the work, we're only
+ * compiling for a single cpu processor type so the default of s3c2440
+ * will be fine with us.
+ */
+
+#include <plat/debug-macro.S>

arch/arm/mach-s5pc100/include/mach/entry-macro.S

+/* arch/arm/mach-s5pc100/include/mach/entry-macro.S
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * Based on mach-s3c6400/include/mach/entry-macro.S
+ *
+ * Low-level IRQ helper macros for the Samsung S5PC1XX series
+ *
+ * This file is licensed under  the terms of the GNU General Public
+ * License version 2. This program is licensed "as is" without any
+ * warranty of any kind, whether express or implied.
+*/
+
+#include <asm/hardware/vic.h>
+#include <mach/map.h>
+#include <plat/irqs.h>
+
+	.macro	disable_fiq
+	.endm
+
+	.macro	get_irqnr_preamble, base, tmp
+	ldr	\base, =S3C_VA_VIC0
+	.endm
+
+	.macro	arch_ret_to_user, tmp1, tmp2
+	.endm
+
+	.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
+
+	@ check the vic0
+	mov	\irqnr, # S3C_IRQ_OFFSET + 31
+	ldr	\irqstat, [ \base, # VIC_IRQ_STATUS ]
+	teq	\irqstat, #0
+
+	@ otherwise try vic1
+	addeq	\tmp, \base, #(S3C_VA_VIC1 - S3C_VA_VIC0)
+	addeq	\irqnr, \irqnr, #32
+	ldreq	\irqstat, [ \tmp, # VIC_IRQ_STATUS ]
+	teqeq	\irqstat, #0
+
+	@ otherwise try vic2
+	addeq	\tmp, \base, #(S3C_VA_VIC2 - S3C_VA_VIC0)
+	addeq	\irqnr, \irqnr, #32
+	ldreq	\irqstat, [ \tmp, # VIC_IRQ_STATUS ]
+	teqeq	\irqstat, #0
+
+	clzne	\irqstat, \irqstat
+	subne	\irqnr, \irqnr, \irqstat
+	.endm

arch/arm/mach-s5pc100/include/mach/gpio-core.h

+/* arch/arm/mach-s5pc100/include/mach/gpio-core.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - GPIO core support
+ *
+ * Based on mach-s3c6400/include/mach/gpio-core.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_GPIO_CORE_H
+#define __ASM_ARCH_GPIO_CORE_H __FILE__
+
+/* currently we just include the platform support */
+#include <plat/gpio-core.h>
+
+#endif /* __ASM_ARCH_GPIO_CORE_H */

arch/arm/mach-s5pc100/include/mach/gpio.h

+/* arch/arm/mach-s5pc100/include/mach/gpio.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - GPIO lib support
+ *
+ * Base on mach-s3c6400/include/mach/gpio.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#define gpio_get_value	__gpio_get_value
+#define gpio_set_value	__gpio_set_value
+#define gpio_cansleep	__gpio_cansleep
+#define gpio_to_irq	__gpio_to_irq
+
+/* GPIO bank sizes */
+#define S5PC1XX_GPIO_A0_NR	(8)
+#define S5PC1XX_GPIO_A1_NR	(5)
+#define S5PC1XX_GPIO_B_NR	(8)
+#define S5PC1XX_GPIO_C_NR	(5)
+#define S5PC1XX_GPIO_D_NR	(7)
+#define S5PC1XX_GPIO_E0_NR	(8)
+#define S5PC1XX_GPIO_E1_NR	(6)
+#define S5PC1XX_GPIO_F0_NR	(8)
+#define S5PC1XX_GPIO_F1_NR	(8)
+#define S5PC1XX_GPIO_F2_NR	(8)
+#define S5PC1XX_GPIO_F3_NR	(4)
+#define S5PC1XX_GPIO_G0_NR	(8)
+#define S5PC1XX_GPIO_G1_NR	(3)
+#define S5PC1XX_GPIO_G2_NR	(7)
+#define S5PC1XX_GPIO_G3_NR	(7)
+#define S5PC1XX_GPIO_H0_NR	(8)
+#define S5PC1XX_GPIO_H1_NR	(8)
+#define S5PC1XX_GPIO_H2_NR	(8)
+#define S5PC1XX_GPIO_H3_NR	(8)
+#define S5PC1XX_GPIO_I_NR	(8)
+#define S5PC1XX_GPIO_J0_NR	(8)
+#define S5PC1XX_GPIO_J1_NR	(5)
+#define S5PC1XX_GPIO_J2_NR	(8)
+#define S5PC1XX_GPIO_J3_NR	(8)
+#define S5PC1XX_GPIO_J4_NR	(4)
+#define S5PC1XX_GPIO_K0_NR	(8)
+#define S5PC1XX_GPIO_K1_NR	(6)
+#define S5PC1XX_GPIO_K2_NR	(8)
+#define S5PC1XX_GPIO_K3_NR	(8)
+#define S5PC1XX_GPIO_MP00_NR	(8)
+#define S5PC1XX_GPIO_MP01_NR	(8)
+#define S5PC1XX_GPIO_MP02_NR	(8)
+#define S5PC1XX_GPIO_MP03_NR	(8)
+#define S5PC1XX_GPIO_MP04_NR	(5)
+
+/* GPIO bank numbes */
+
+/* CONFIG_S3C_GPIO_SPACE allows the user to select extra
+ * space for debugging purposes so that any accidental
+ * change from one gpio bank to another can be caught.
+*/
+
+#define S5PC1XX_GPIO_NEXT(__gpio) \
+	((__gpio##_START) + (__gpio##_NR) + CONFIG_S3C_GPIO_SPACE + 1)
+
+enum s3c_gpio_number {
+	S5PC1XX_GPIO_A0_START 	= 0,
+	S5PC1XX_GPIO_A1_START 	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_A0),
+	S5PC1XX_GPIO_B_START 	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_A1),
+	S5PC1XX_GPIO_C_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_B),
+	S5PC1XX_GPIO_D_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_C),
+	S5PC1XX_GPIO_E0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_D),
+	S5PC1XX_GPIO_E1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_E0),
+	S5PC1XX_GPIO_F0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_E1),
+	S5PC1XX_GPIO_F1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_F0),
+	S5PC1XX_GPIO_F2_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_F1),
+	S5PC1XX_GPIO_F3_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_F2),
+	S5PC1XX_GPIO_G0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_F3),
+	S5PC1XX_GPIO_G1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_G0),
+	S5PC1XX_GPIO_G2_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_G1),
+	S5PC1XX_GPIO_G3_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_G2),
+	S5PC1XX_GPIO_H0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_G3),
+	S5PC1XX_GPIO_H1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_H0),
+	S5PC1XX_GPIO_H2_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_H1),
+	S5PC1XX_GPIO_H3_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_H2),
+	S5PC1XX_GPIO_I_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_H3),
+	S5PC1XX_GPIO_J0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_I),
+	S5PC1XX_GPIO_J1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_J0),
+	S5PC1XX_GPIO_J2_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_J1),
+	S5PC1XX_GPIO_J3_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_J2),
+	S5PC1XX_GPIO_J4_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_J3),
+	S5PC1XX_GPIO_K0_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_J4),
+	S5PC1XX_GPIO_K1_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_K0),
+	S5PC1XX_GPIO_K2_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_K1),
+	S5PC1XX_GPIO_K3_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_K2),
+	S5PC1XX_GPIO_MP00_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_K3),
+	S5PC1XX_GPIO_MP01_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_MP00),
+	S5PC1XX_GPIO_MP02_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_MP01),
+	S5PC1XX_GPIO_MP03_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_MP02),
+	S5PC1XX_GPIO_MP04_START	= S5PC1XX_GPIO_NEXT(S5PC1XX_GPIO_MP03),
+};
+
+/* S5PC1XX GPIO number definitions. */
+#define S5PC1XX_GPA0(_nr)	(S5PC1XX_GPIO_A0_START + (_nr))
+#define S5PC1XX_GPA1(_nr)	(S5PC1XX_GPIO_A1_START + (_nr))
+#define S5PC1XX_GPB(_nr)	(S5PC1XX_GPIO_B_START + (_nr))
+#define S5PC1XX_GPC(_nr)	(S5PC1XX_GPIO_C_START + (_nr))
+#define S5PC1XX_GPD(_nr)	(S5PC1XX_GPIO_D_START + (_nr))
+#define S5PC1XX_GPE0(_nr)	(S5PC1XX_GPIO_E0_START + (_nr))
+#define S5PC1XX_GPE1(_nr)	(S5PC1XX_GPIO_E1_START + (_nr))
+#define S5PC1XX_GPF0(_nr)	(S5PC1XX_GPIO_F0_START + (_nr))
+#define S5PC1XX_GPF1(_nr)	(S5PC1XX_GPIO_F1_START + (_nr))
+#define S5PC1XX_GPF2(_nr)	(S5PC1XX_GPIO_F2_START + (_nr))
+#define S5PC1XX_GPF3(_nr)	(S5PC1XX_GPIO_F3_START + (_nr))
+#define S5PC1XX_GPG0(_nr)	(S5PC1XX_GPIO_G0_START + (_nr))
+#define S5PC1XX_GPG1(_nr)	(S5PC1XX_GPIO_G1_START + (_nr))
+#define S5PC1XX_GPG2(_nr)	(S5PC1XX_GPIO_G2_START + (_nr))
+#define S5PC1XX_GPG3(_nr)	(S5PC1XX_GPIO_G3_START + (_nr))
+#define S5PC1XX_GPH0(_nr)	(S5PC1XX_GPIO_H0_START + (_nr))
+#define S5PC1XX_GPH1(_nr)	(S5PC1XX_GPIO_H1_START + (_nr))
+#define S5PC1XX_GPH2(_nr)	(S5PC1XX_GPIO_H2_START + (_nr))
+#define S5PC1XX_GPH3(_nr)	(S5PC1XX_GPIO_H3_START + (_nr))
+#define S5PC1XX_GPI(_nr)	(S5PC1XX_GPIO_I_START + (_nr))
+#define S5PC1XX_GPJ0(_nr)	(S5PC1XX_GPIO_J0_START + (_nr))
+#define S5PC1XX_GPJ1(_nr)	(S5PC1XX_GPIO_J1_START + (_nr))
+#define S5PC1XX_GPJ2(_nr)	(S5PC1XX_GPIO_J2_START + (_nr))
+#define S5PC1XX_GPJ3(_nr)	(S5PC1XX_GPIO_J3_START + (_nr))
+#define S5PC1XX_GPJ4(_nr)	(S5PC1XX_GPIO_J4_START + (_nr))
+#define S5PC1XX_GPK0(_nr)	(S5PC1XX_GPIO_K0_START + (_nr))
+#define S5PC1XX_GPK1(_nr)	(S5PC1XX_GPIO_K1_START + (_nr))
+#define S5PC1XX_GPK2(_nr)	(S5PC1XX_GPIO_K2_START + (_nr))
+#define S5PC1XX_GPK3(_nr)	(S5PC1XX_GPIO_K3_START + (_nr))
+#define S5PC1XX_MP00(_nr)	(S5PC1XX_GPIO_MP00_START + (_nr))
+#define S5PC1XX_MP01(_nr)	(S5PC1XX_GPIO_MP01_START + (_nr))
+#define S5PC1XX_MP02(_nr)	(S5PC1XX_GPIO_MP02_START + (_nr))
+#define S5PC1XX_MP03(_nr)	(S5PC1XX_GPIO_MP03_START + (_nr))
+#define S5PC1XX_MP04(_nr)	(S5PC1XX_GPIO_MP04_START + (_nr))
+
+/* the end of the S5PC1XX specific gpios */
+#define S5PC1XX_GPIO_END	(S5PC1XX_MP04(S5PC1XX_GPIO_MP04_NR) + 1)
+#define S3C_GPIO_END		S5PC1XX_GPIO_END
+
+/* define the number of gpios we need to the one after the MP04() range */
+#define ARCH_NR_GPIOS	(S5PC1XX_MP04(S5PC1XX_GPIO_MP04_NR) + 1)
+
+#include <asm-generic/gpio.h>

arch/arm/mach-s5pc100/include/mach/hardware.h

+/* linux/arch/arm/mach-s5pc100/include/mach/hardware.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - Hardware support
+ */
+
+#ifndef __ASM_ARCH_HARDWARE_H
+#define __ASM_ARCH_HARDWARE_H __FILE__
+
+/* currently nothing here, placeholder */
+
+#endif /* __ASM_ARCH_HARDWARE_H */

arch/arm/mach-s5pc100/include/mach/irqs.h

+/* linux/arch/arm/mach-s5pc100/include/mach/irqs.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - IRQ definitions
+ */
+
+#ifndef __ASM_ARCH_IRQS_H
+#define __ASM_ARCH_IRQS_H __FILE__
+
+#include <plat/irqs.h>
+
+#endif /* __ASM_ARCH_IRQ_H */

arch/arm/mach-s5pc100/include/mach/map.h

+/* linux/arch/arm/mach-s5pc100/include/mach/map.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * Based on mach-s3c6400/include/mach/map.h
+ *
+ * S5PC1XX - Memory map definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_MAP_H
+#define __ASM_ARCH_MAP_H __FILE__
+
+#include <plat/map-base.h>
+
+
+/* Chip ID */
+#define S5PC100_PA_CHIPID	(0xE0000000)
+#define S5PC1XX_PA_CHIPID	S5PC100_PA_CHIPID
+#define S5PC1XX_VA_CHIPID	S3C_VA_SYS
+
+/* System */
+#define S5PC100_PA_SYS		(0xE0100000)
+#define S5PC100_PA_CLK		(S5PC100_PA_SYS + 0x0)
+#define S5PC100_PA_PWR		(S5PC100_PA_SYS + 0x8000)
+#define S5PC1XX_PA_CLK		S5PC100_PA_CLK
+#define S5PC1XX_PA_PWR		S5PC100_PA_PWR
+#define S5PC1XX_VA_CLK		(S3C_VA_SYS + 0x10000)
+#define S5PC1XX_VA_PWR		(S3C_VA_SYS + 0x20000)
+
+/* Interrupt */
+#define S5PC100_PA_VIC		(0xE4000000)
+#define S5PC100_VA_VIC		S3C_VA_IRQ
+#define S5PC100_PA_VIC_OFFSET	0x100000
+#define S5PC100_VA_VIC_OFFSET	0x10000
+#define S5PC1XX_PA_VIC(x)	(S5PC100_PA_VIC + ((x) * S5PC100_PA_VIC_OFFSET))
+#define S5PC1XX_VA_VIC(x)	(S5PC100_VA_VIC + ((x) * S5PC100_VA_VIC_OFFSET))
+
+/* Timer */
+#define S5PC100_PA_TIMER	(0xEA000000)
+#define S5PC1XX_PA_TIMER	S5PC100_PA_TIMER
+#define S5PC1XX_VA_TIMER	S3C_VA_TIMER
+
+/* UART */
+#define S5PC100_PA_UART		(0xEC000000)
+#define S5PC1XX_PA_UART		S5PC100_PA_UART
+#define S5PC1XX_VA_UART		S3C_VA_UART
+
+/* IIC */
+#define S5PC100_PA_IIC		(0xEC100000)
+
+/* ETC */
+#define S5PC100_PA_SDRAM	(0x20000000)
+
+/* compatibility defines. */
+#define S3C_PA_UART		S5PC100_PA_UART
+#define S3C_PA_UART0		(S5PC100_PA_UART + 0x0)
+#define S3C_PA_UART1		(S5PC100_PA_UART + 0x400)
+#define S3C_PA_UART2		(S5PC100_PA_UART + 0x800)
+#define S3C_PA_UART3		(S5PC100_PA_UART + 0xC00)
+#define S3C_VA_UART0		(S3C_VA_UART + 0x0)
+#define S3C_VA_UART1		(S3C_VA_UART + 0x400)
+#define S3C_VA_UART2		(S3C_VA_UART + 0x800)
+#define S3C_VA_UART3		(S3C_VA_UART + 0xC00)
+#define S3C_UART_OFFSET		0x400
+#define S3C_VA_VIC0		(S3C_VA_IRQ + 0x0)
+#define S3C_VA_VIC1		(S3C_VA_IRQ + 0x10000)
+#define S3C_VA_VIC2		(S3C_VA_IRQ + 0x20000)
+#define S3C_PA_IIC		S5PC100_PA_IIC
+
+#endif /* __ASM_ARCH_C100_MAP_H */

arch/arm/mach-s5pc100/include/mach/memory.h

+/* arch/arm/mach-s5pc100/include/mach/memory.h
+ *
+ * Copyright 2008 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * Based on mach-s3c6400/include/mach/memory.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_MEMORY_H
+#define __ASM_ARCH_MEMORY_H
+
+#define PHYS_OFFSET     	UL(0x20000000)
+
+#endif

arch/arm/mach-s5pc100/include/mach/pwm-clock.h

+/* linux/arch/arm/mach-s5pc100/include/mach/pwm-clock.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - pwm clock and timer support
+ *
+ * Based on mach-s3c6400/include/mach/pwm-clock.h
+ */
+
+/**
+ * pwm_cfg_src_is_tclk() - return whether the given mux config is a tclk
+ * @tcfg: The timer TCFG1 register bits shifted down to 0.
+ *
+ * Return true if the given configuration from TCFG1 is a TCLK instead
+ * any of the TDIV clocks.
+ */
+static inline int pwm_cfg_src_is_tclk(unsigned long tcfg)
+{
+	return tcfg >= S3C64XX_TCFG1_MUX_TCLK;
+}
+
+/**
+ * tcfg_to_divisor() - convert tcfg1 setting to a divisor
+ * @tcfg1: The tcfg1 setting, shifted down.
+ *
+ * Get the divisor value for the given tcfg1 setting. We assume the
+ * caller has already checked to see if this is not a TCLK source.
+ */
+static inline unsigned long tcfg_to_divisor(unsigned long tcfg1)
+{
+	return 1 << tcfg1;
+}
+
+/**
+ * pwm_tdiv_has_div1() - does the tdiv setting have a /1
+ *
+ * Return true if we have a /1 in the tdiv setting.
+ */
+static inline unsigned int pwm_tdiv_has_div1(void)
+{
+	return 1;
+}
+
+/**
+ * pwm_tdiv_div_bits() - calculate TCFG1 divisor value.
+ * @div: The divisor to calculate the bit information for.
+ *
+ * Turn a divisor into the necessary bit field for TCFG1.
+ */
+static inline unsigned long pwm_tdiv_div_bits(unsigned int div)
+{
+	return ilog2(div);
+}
+
+#define S3C_TCFG1_MUX_TCLK S3C64XX_TCFG1_MUX_TCLK

arch/arm/mach-s5pc100/include/mach/regs-irq.h

+/* linux/arch/arm/mach-s5pc100/include/mach/regs-irq.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC1XX - IRQ register definitions
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_REGS_IRQ_H
+#define __ASM_ARCH_REGS_IRQ_H __FILE__
+
+#include <mach/map.h>
+#include <asm/hardware/vic.h>
+
+/* interrupt controller */
+#define S5PC1XX_VIC0REG(x)          		((x) + S5PC1XX_VA_VIC(0))
+#define S5PC1XX_VIC1REG(x)          		((x) + S5PC1XX_VA_VIC(1))
+#define S5PC1XX_VIC2REG(x)         		((x) + S5PC1XX_VA_VIC(2))
+
+#endif /* __ASM_ARCH_REGS_IRQ_H */

arch/arm/mach-s5pc100/include/mach/system.h

+/* linux/arch/arm/mach-s5pc100/include/mach/system.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *      Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC1XX - system implementation
+ *
+ * Based on mach-s3c6400/include/mach/system.h
+ */
+
+#ifndef __ASM_ARCH_SYSTEM_H
+#define __ASM_ARCH_SYSTEM_H __FILE__
+
+static void arch_idle(void)
+{
+	/* nothing here yet */
+}
+
+static void arch_reset(char mode, const char *cmd)
+{
+	/* nothing here yet */
+}
+
+#endif /* __ASM_ARCH_IRQ_H */

arch/arm/mach-s5pc100/include/mach/tick.h

+/* linux/arch/arm/mach-s5pc100/include/mach/tick.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * S3C64XX - Timer tick support definitions
+ *
+ * Based on mach-s3c6400/include/mach/tick.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_TICK_H
+#define __ASM_ARCH_TICK_H __FILE__
+
+/* note, the timer interrutps turn up in 2 places, the vic and then
+ * the timer block. We take the VIC as the base at the moment.
+ */
+static inline u32 s3c24xx_ostimer_pending(void)
+{
+	u32 pend = __raw_readl(S3C_VA_VIC0 + VIC_RAW_STATUS);
+	return pend & 1 << (IRQ_TIMER4 - S5PC1XX_IRQ_VIC0(0));
+}
+
+#define TICK_MAX	(0xffffffff)
+
+#endif /* __ASM_ARCH_TICK_H */

arch/arm/mach-s5pc100/include/mach/uncompress.h

+/* arch/arm/mach-s5pc100/include/mach/uncompress.h
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ *	Byungho Min <bhmin@samsung.com>
+ *
+ * S5PC100 - uncompress code
+ *
+ * Based on mach-s3c6400/include/mach/uncompress.h
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_UNCOMPRESS_H
+#define __ASM_ARCH_UNCOMPRESS_H
+
+#include <mach/map.h>
+#include <plat/uncompress.h>
+
+static void arch_detect_cpu(void)
+{
+	/* we do not need to do any cpu detection here at the moment. */
+	fifo_mask = S3C2440_UFSTAT_TXMASK;
+	fifo_max = 63 << S3C2440_UFSTAT_TXSHIFT;
+}
+
+#endif /* __ASM_ARCH_UNCOMPRESS_H */

arch/arm/mach-s5pc100/mach-smdkc100.c

+/* linux/arch/arm/mach-s5pc100/mach-smdkc100.c
+ *
+ * Copyright 2009 Samsung Electronics Co.
+ * Author: Byungho Min <bhmin@samsung.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+*/
+
+#include <linux/kernel.h>
+#include <linux/types.h>
+#include <linux/interrupt.h>
+#include <linux/list.h>
+#include <linux/timer.h>
+#include <linux/init.h>
+#include <linux/serial_core.h>
+#include <linux/platform_device.h>
+#include <linux/io.h>
+#include <linux/gpio.h>
+#include <linux/i2c.h>
+#include <linux/fb.h>
+#include <linux/delay.h>
+
+#include <asm/mach/arch.h>
+#include <asm/mach/map.h>
+
+#include <mach/map.h>
+
+#include <asm/irq.h>
+#include <asm/mach-types.h>
+
+#include <plat/regs-serial.h>
+
+#include <plat/clock.h>
+#include <plat/devs.h>
+#include <plat/cpu.h>
+#include <plat/s5pc100.h>
+
+#define UCON (S3C2410_UCON_DEFAULT | S3C2410_UCON_UCLK)
+#define ULCON (S3C2410_LCON_CS8 | S3C2410_LCON_PNONE | S3C2410_LCON_STOPB)
+#define UFCON (S3C2410_UFCON_RXTRIG8 | S3C2410_UFCON_FIFOMODE)
+
+static struct s3c2410_uartcfg smdkc100_uartcfgs[] __initdata = {
+	[0] = {
+		.hwport	     = 0,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[1] = {
+		.hwport	     = 1,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[2] = {
+		.hwport	     = 2,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+	[3] = {
+		.hwport	     = 3,
+		.flags	     = 0,
+		.ucon	     = 0x3c5,
+		.ulcon	     = 0x03,
+		.ufcon	     = 0x51,
+	},
+};
+
+static struct map_desc smdkc100_iodesc[] = {};
+
+static struct platform_device *smdkc100_devices[] __initdata = {
+};
+
+static void __init smdkc100_map_io(void)
+{
+	s5pc1xx_init_io(smdkc100_iodesc, ARRAY_SIZE(smdkc100_iodesc));
+	s3c24xx_init_clocks(12000000);
+	s3c24xx_init_uarts(smdkc100_uartcfgs, ARRAY_SIZE(smdkc100_uartcfgs));
+}
+
+static void __init smdkc100_machine_init(void)
+{
+	platform_add_devices(smdkc100_devices, ARRAY_SIZE(smdkc100_devices));
+}
+
+MACHINE_START(SMDKC100, "SMDKC100")
+	/* Maintainer: Byungho Min <bhmin@samsung.com> */
+	.phys_io	= S5PC1XX_PA_UART & 0xfff00000,
+	.io_pg_offst	= (((u32)S5PC1XX_VA_UART) >> 18) & 0xfffc,
+	.boot_params	= S5PC100_PA_SDRAM + 0x100,
+
+	.init_irq	= s5pc100_init_irq,
+	.map_io		= smdkc100_map_io,
+	.init_machine	= smdkc100_machine_init,
+	.timer		= &s3c24xx_timer,
+MACHINE_END

arch/arm/plat-s3c/Kconfig

@@ -198,4 +198,9 @@ config S3C_DEV_USB_HSOTG
 	help
 	  Compile in platform device definition for USB high-speed OtG
 
+config S3C_DEV_NAND
+	bool
+	help
+	  Compile in platform device definition for NAND controller
+
 endif

arch/arm/plat-s3c/Makefile

@@ -28,13 +28,17 @@ obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_PM)		+= pm-gpio.o
 obj-$(CONFIG_S3C2410_PM_CHECK)	+= pm-check.o
 
+# PWM support
+
+obj-$(CONFIG_HAVE_PWM)		+= pwm.o
+
 # devices
 
 obj-$(CONFIG_S3C_DEV_HSMMC)	+= dev-hsmmc.o
 obj-$(CONFIG_S3C_DEV_HSMMC1)	+= dev-hsmmc1.o
 obj-y				+= dev-i2c0.o
 obj-$(CONFIG_S3C_DEV_I2C1)	+= dev-i2c1.o
-obj-$(CONFIG_SND_S3C64XX_SOC_I2S)	+= dev-audio.o
 obj-$(CONFIG_S3C_DEV_FB)	+= dev-fb.o
 obj-$(CONFIG_S3C_DEV_USB_HOST)	+= dev-usb.o
 obj-$(CONFIG_S3C_DEV_USB_HSOTG)	+= dev-usb-hsotg.o
+obj-$(CONFIG_S3C_DEV_NAND)	+= dev-nand.o

arch/arm/plat-s3c/dev-nand.c

+/*
+ * S3C series device definition for nand device
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/platform_device.h>
+
+#include <mach/map.h>
+#include <plat/devs.h>
+
+static struct resource s3c_nand_resource[] = {
+	[0] = {
+		.start = S3C_PA_NAND,
+		.end   = S3C_PA_NAND + SZ_1M,
+		.flags = IORESOURCE_MEM,
+	}
+};
+
+struct platform_device s3c_device_nand = {
+	.name		  = "s3c2410-nand",
+	.id		  = -1,
+	.num_resources	  = ARRAY_SIZE(s3c_nand_resource),
+	.resource	  = s3c_nand_resource,
+};
+
+EXPORT_SYMBOL(s3c_device_nand);

arch/arm/plat-s3c/include/plat/adc.h

@@ -19,10 +19,14 @@ struct s3c_adc_client;
 extern int s3c_adc_start(struct s3c_adc_client *client,
 			 unsigned int channel, unsigned int nr_samples);
 
+extern int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch);
+
 extern struct s3c_adc_client *
 	s3c_adc_register(struct platform_device *pdev,
-			 void (*select)(unsigned selected),
-			 void (*conv)(unsigned d0, unsigned d1,
+			 void (*select)(struct s3c_adc_client *client,
+					unsigned selected),
+			 void (*conv)(struct s3c_adc_client *client,
+				      unsigned d0, unsigned d1,
 				      unsigned *samples_left),
 			 unsigned int is_ts);
 

arch/arm/plat-s3c/include/plat/cpu-freq.h

@@ -17,6 +17,21 @@ struct s3c_cpufreq_info;
 struct s3c_cpufreq_board;
 struct s3c_iotimings;
 
+/**
+ * struct s3c_freq - frequency information (mainly for core drivers)
+ * @fclk: The FCLK frequency in Hz.
+ * @armclk: The ARMCLK frequency in Hz.
+ * @hclk_tns: HCLK cycle time in 10ths of nano-seconds.
+ * @hclk: The HCLK frequency in Hz.
+ * @pclk: The PCLK frequency in Hz.
+ *
+ * This contains the frequency information about the current configuration
+ * mainly for the core drivers to ensure we do not end up passing about
+ * a large number of parameters.
+ *
+ * The @hclk_tns field is a useful cache for the parts of the drivers that
+ * need to calculate IO timings and suchlike.
+ */
 struct s3c_freq {
 	unsigned long	fclk;
 	unsigned long	armclk;
@@ -25,48 +40,84 @@ struct s3c_freq {
 	unsigned long	pclk;
 };
 
-/* wrapper 'struct cpufreq_freqs' so that any drivers receiving the
+/**
+ * struct s3c_cpufreq_freqs - s3c cpufreq notification information.
+ * @freqs: The cpufreq setting information.
+ * @old: The old clock settings.
+ * @new: The new clock settings.
+ * @pll_changing: Set if the PLL is changing.
+ *
+ * Wrapper 'struct cpufreq_freqs' so that any drivers receiving the
  * notification can use this information that is not provided by just
  * having the core frequency alone.
+ *
+ * The pll_changing flag is used to indicate if the PLL itself is
+ * being set during this change. This is important as the clocks
+ * will temporarily be set to the XTAL clock during this time, so
+ * drivers may want to close down their output during this time.
+ *
+ * Note, this is not being used by any current drivers and therefore
+ * may be removed in the future.
  */
-
 struct s3c_cpufreq_freqs {
 	struct cpufreq_freqs	freqs;
 	struct s3c_freq		old;
 	struct s3c_freq		new;
+
+	unsigned int		pll_changing:1;
 };
 
 #define to_s3c_cpufreq(_cf) container_of(_cf, struct s3c_cpufreq_freqs, freqs)
 
+/**
+ * struct s3c_clkdivs - clock divisor information
+ * @p_divisor: Divisor from FCLK to PCLK.
+ * @h_divisor: Divisor from FCLK to HCLK.
+ * @arm_divisor: Divisor from FCLK to ARMCLK (not all CPUs).
+ * @dvs: Non-zero if using DVS mode for ARMCLK.
+ *
+ * Divisor settings for the core clocks.
+ */
 struct s3c_clkdivs {
-	int		p_divisor;	/* fclk / pclk */
-	int		h_divisor;	/* fclk / hclk */
-	int		arm_divisor;	/* not all cpus have this. */
-	unsigned char	dvs;		/* using dvs mode to arm. */
+	int		p_divisor;
+	int		h_divisor;
+	int		arm_divisor;
+	unsigned char	dvs;
 };
 
 #define PLLVAL(_m, _p, _s) (((_m) << 12) | ((_p) << 4) | (_s))
 
+/**
+ * struct s3c_pllval - PLL value entry.
+ * @freq: The frequency for this entry in Hz.
+ * @pll_reg: The PLL register setting for this PLL value.
+ */
 struct s3c_pllval {
 	unsigned long		freq;
 	unsigned long		pll_reg;
 };
 
-struct s3c_cpufreq_config {
-	struct s3c_freq		freq;
-	struct s3c_pllval	pll;
-	struct s3c_clkdivs	divs;
-	struct s3c_cpufreq_info *info;	/* for core, not drivers */
-	struct s3c_cpufreq_board *board;
-};
-
-/* s3c_cpufreq_board
+/**
+ * struct s3c_cpufreq_board - per-board cpu frequency informatin
+ * @refresh: The SDRAM refresh period in nanoseconds.
+ * @auto_io: Set if the IO timing settings should be generated from the
+ *	initialisation time hardware registers.
+ * @need_io: Set if the board has external IO on any of the chipselect
+ *	lines that will require the hardware timing registers to be
+ *	updated on a clock change.
+ * @max: The maxium frequency limits for the system. Any field that
+ *	is left at zero will use the CPU's settings.
+ *
+ * This contains the board specific settings that affect how the CPU
+ * drivers chose settings. These include the memory refresh and IO
+ * timing information.
  *
- * per-board configuraton information, such as memory refresh and
- * how to initialise IO timings.
+ * Registration depends on the driver being used, the ARMCLK only
+ * implementation does not currently need this but the older style
+ * driver requires this to be available.
  */
 struct s3c_cpufreq_board {
-	unsigned int	refresh;	/* refresh period in ns */
+	unsigned int	refresh;
 	unsigned int	auto_io:1;	/* automatically init io timings. */
 	unsigned int	need_io:1;	/* set if needs io timing support. */
 

arch/arm/plat-s3c/include/plat/cpu.h

@@ -65,6 +65,7 @@ extern struct sys_timer s3c24xx_timer;
 /* system device classes */
 
 extern struct sysdev_class s3c2410_sysclass;
+extern struct sysdev_class s3c2410a_sysclass;
 extern struct sysdev_class s3c2412_sysclass;
 extern struct sysdev_class s3c2440_sysclass;
 extern struct sysdev_class s3c2442_sysclass;

arch/arm/plat-s3c/include/plat/devs.h

@@ -46,6 +46,8 @@ extern struct platform_device s3c_device_hsmmc2;
 extern struct platform_device s3c_device_spi0;
 extern struct platform_device s3c_device_spi1;
 
+extern struct platform_device s3c_device_hwmon;
+
 extern struct platform_device s3c_device_nand;
 
 extern struct platform_device s3c_device_usbgadget;
@@ -56,5 +58,6 @@ extern struct platform_device s3c_device_usb_hsotg;
 #ifdef CONFIG_CPU_S3C2440
 
 extern struct platform_device s3c_device_camif;
+extern struct platform_device s3c_device_ac97;
 
 #endif

arch/arm/plat-s3c/include/plat/hwmon.h

+/* linux/arch/arm/plat-s3c/include/plat/hwmon.h
+ *
+ * Copyright 2005 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *	http://armlinux.simtec.co.uk/
+ *
+ * S3C - HWMon interface for ADC
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#ifndef __ASM_ARCH_ADC_HWMON_H
+#define __ASM_ARCH_ADC_HWMON_H __FILE__
+
+/**
+ * s3c_hwmon_chcfg - channel configuration
+ * @name: The name to give this channel.
+ * @mult: Multiply the ADC value read by this.
+ * @div: Divide the value from the ADC by this.
+ *
+ * The value read from the ADC is converted to a value that
+ * hwmon expects (mV) by result = (value_read * @mult) / @div.
+ */
+struct s3c_hwmon_chcfg {
+	const char	*name;
+	unsigned int	mult;
+	unsigned int	div;
+};
+
+/**
+ * s3c_hwmon_pdata - HWMON platform data
+ * @in: One configuration for each possible channel used.
+ */
+struct s3c_hwmon_pdata {
+	struct s3c_hwmon_chcfg	*in[8];
+};
+
+#endif /* __ASM_ARCH_ADC_HWMON_H */
+

arch/arm/plat-s3c/include/plat/map-base.h

@@ -32,9 +32,15 @@
 
 #define S3C_VA_IRQ	S3C_ADDR(0x00000000)	/* irq controller(s) */
 #define S3C_VA_SYS	S3C_ADDR(0x00100000)	/* system control */
-#define S3C_VA_MEM	S3C_ADDR(0x00200000)	/* system control */
+#define S3C_VA_MEM	S3C_ADDR(0x00200000)	/* memory control */
 #define S3C_VA_TIMER	S3C_ADDR(0x00300000)	/* timer block */
 #define S3C_VA_WATCHDOG	S3C_ADDR(0x00400000)	/* watchdog */
 #define S3C_VA_UART	S3C_ADDR(0x01000000)	/* UART */
 
+/* This is used for the CPU specific mappings that may be needed, so that
+ * they do not need to directly used S3C_ADDR() and thus make it easier to
+ * modify the space for mapping.
+ */
+#define S3C_ADDR_CPU(x)	S3C_ADDR(0x00500000 + (x))
+
 #endif /* __ASM_PLAT_MAP_H */

arch/arm/plat-s3c24xx/pwm.c → arch/arm/plat-s3c/pwm.c

-/* arch/arm/plat-s3c24xx/pwm.c
+/* arch/arm/plat-s3c/pwm.c
  *
  * Copyright (c) 2007 Ben Dooks
  * Copyright (c) 2008 Simtec Electronics
  *	Ben Dooks <ben@simtec.co.uk>, <ben-linux@fluff.org>
  *
- * S3C24XX PWM device core
+ * S3C series PWM device core
  *
  * This program is free software; you can redistribute it and/or modify
  * it under the terms of the GNU General Public License as published by
@@ -20,6 +20,7 @@
 #include <linux/pwm.h>
 
 #include <mach/irqs.h>
+#include <mach/map.h>
 
 #include <plat/devs.h>
 #include <plat/regs-timer.h>

arch/arm/plat-s3c24xx/Kconfig

@@ -10,6 +10,7 @@ config PLAT_S3C24XX
 	default y
 	select NO_IOPORT
 	select ARCH_REQUIRE_GPIOLIB
+	select S3C_DEVICE_NAND
 	help
 	  Base platform code for any Samsung S3C24XX device
 
@@ -34,6 +35,40 @@ config CPU_S3C244X
 	help
 	  Support for S3C2440 and S3C2442 Samsung Mobile CPU based systems.
 
+config S3C2440_CPUFREQ
+	bool "S3C2440/S3C2442 CPU Frequency scaling support"
+	depends on CPU_FREQ_S3C24XX && (CPU_S3C2440 || CPU_S3C2442)
+	select S3C2410_CPUFREQ_UTILS
+	default y
+	help
+	  CPU Frequency scaling support for S3C2440 and S3C2442 SoC CPUs.
+
+config S3C2440_XTAL_12000000
+	bool
+	help
+	  Indicate that the build needs to support 12MHz system
+	  crystal.
+
+config S3C2440_XTAL_16934400
+	bool
+	help
+	  Indicate that the build needs to support 16.9344MHz system
+	  crystal.
+
+config S3C2440_PLL_12000000
+	bool
+	depends on S3C2440_CPUFREQ && S3C2440_XTAL_12000000
+	default y if CPU_FREQ_S3C24XX_PLL
+	help
+	  PLL tables for S3C2440 or S3C2442 CPUs with 12MHz crystals.
+
+config S3C2440_PLL_16934400
+	bool
+	depends on S3C2440_CPUFREQ && S3C2440_XTAL_16934400
+	default y if CPU_FREQ_S3C24XX_PLL
+	help
+	  PLL tables for S3C2440 or S3C2442 CPUs with 16.934MHz crystals.
+
 config S3C24XX_PWM
 	bool "PWM device support"
 	select HAVE_PWM
@@ -105,8 +140,39 @@ config S3C24XX_SPI_BUS1_GPG5_GPG6_GPG7
 	  SPI GPIO configuration code for BUS 1 when connected to
 	  GPG5, GPG6 and GPG7.
 
+config S3C24XX_SPI_BUS1_GPD8_GPD9_GPD10
+	bool
+	help
+	  SPI GPIO configuration code for BUS 1 when connected to
+	  GPD8, GPD9 and GPD10.
+
 # common code for s3c24xx based machines, such as the SMDKs.
 
+# cpu frequency items common between s3c2410 and s3c2440/s3c2442
+
+config S3C2410_IOTIMING
+	bool
+	depends on CPU_FREQ_S3C24XX
+	help
+	  Internal node to select io timing code that is common to the s3c2410
+	  and s3c2440/s3c2442 cpu frequency support.
+
+config S3C2410_CPUFREQ_UTILS
+	bool
+	depends on CPU_FREQ_S3C24XX
+	help
+	  Internal node to select timing code that is common to the s3c2410
+	  and s3c2440/s3c244 cpu frequency support.
+
+# cpu frequency support common to s3c2412, s3c2413 and s3c2442
+
+config S3C2412_IOTIMING
+	bool
+	depends on CPU_FREQ_S3C24XX && (CPU_S3C2412 || CPU_S3C2443)
+	help
+	  Intel node to select io timing code that is common to the s3c2412
+	  and the s3c2443.
+
 config MACH_SMDK
 	bool
 	help

arch/arm/plat-s3c24xx/Makefile

@@ -20,19 +20,28 @@ obj-y				+= gpiolib.o
 obj-y				+= clock.o
 obj-$(CONFIG_S3C24XX_DCLK)	+= clock-dclk.o
 
+obj-$(CONFIG_CPU_FREQ_S3C24XX)	+= cpu-freq.o
+obj-$(CONFIG_CPU_FREQ_S3C24XX_DEBUGFS) += cpu-freq-debugfs.o
+
 # Architecture dependant builds
 
 obj-$(CONFIG_CPU_S3C244X)	+= s3c244x.o
 obj-$(CONFIG_CPU_S3C244X)	+= s3c244x-irq.o
 obj-$(CONFIG_CPU_S3C244X)	+= s3c244x-clock.o
+obj-$(CONFIG_S3C2440_CPUFREQ)	+= s3c2440-cpufreq.o
+obj-$(CONFIG_S3C2440_PLL_12000000) += s3c2440-pll-12000000.o
+obj-$(CONFIG_S3C2440_PLL_16934400) += s3c2440-pll-16934400.o
+
 obj-$(CONFIG_PM_SIMTEC)		+= pm-simtec.o
 obj-$(CONFIG_PM)		+= pm.o
 obj-$(CONFIG_PM)		+= irq-pm.o
 obj-$(CONFIG_PM)		+= sleep.o
-obj-$(CONFIG_S3C24XX_PWM)	+= pwm.o
 obj-$(CONFIG_S3C2410_CLOCK)	+= s3c2410-clock.o
 obj-$(CONFIG_S3C2410_DMA)	+= dma.o
 obj-$(CONFIG_S3C24XX_ADC)	+= adc.o
+obj-$(CONFIG_S3C2410_IOTIMING)	+= s3c2410-iotiming.o
+obj-$(CONFIG_S3C2412_IOTIMING)	+= s3c2412-iotiming.o
+obj-$(CONFIG_S3C2410_CPUFREQ_UTILS) += s3c2410-cpufreq-utils.o
 
 # device specific setup and/or initialisation
 obj-$(CONFIG_ARCH_S3C2410)	+= setup-i2c.o
@@ -41,6 +50,7 @@ obj-$(CONFIG_ARCH_S3C2410)	+= setup-i2c.o
 
 obj-$(CONFIG_S3C24XX_SPI_BUS0_GPE11_GPE12_GPE13) += spi-bus0-gpe11_12_13.o
 obj-$(CONFIG_S3C24XX_SPI_BUS1_GPG5_GPG6_GPG7)    += spi-bus1-gpg5_6_7.o
+obj-$(CONFIG_S3C24XX_SPI_BUS1_GPD8_GPD9_GPD10)	 += spi-bus1-gpd8_9_10.o
 
 # machine common support
 

arch/arm/plat-s3c24xx/adc.c

@@ -39,13 +39,16 @@
 struct s3c_adc_client {
 	struct platform_device	*pdev;
 	struct list_head	 pend;
+	wait_queue_head_t	*wait;
 
 	unsigned int		 nr_samples;
+	int			 result;
 	unsigned char		 is_ts;
 	unsigned char		 channel;
 
-	void	(*select_cb)(unsigned selected);
-	void	(*convert_cb)(unsigned val1, unsigned val2,
+	void	(*select_cb)(struct s3c_adc_client *c, unsigned selected);
+	void	(*convert_cb)(struct s3c_adc_client *c,
+			      unsigned val1, unsigned val2,
 			      unsigned *samples_left);
 };
 
@@ -81,7 +84,7 @@ static inline void s3c_adc_select(struct adc_device *adc,
 {
 	unsigned con = readl(adc->regs + S3C2410_ADCCON);
 
-	client->select_cb(1);
+	client->select_cb(client, 1);
 
 	con &= ~S3C2410_ADCCON_MUXMASK;
 	con &= ~S3C2410_ADCCON_STDBM;
@@ -153,25 +156,61 @@ int s3c_adc_start(struct s3c_adc_client *client,
 }
 EXPORT_SYMBOL_GPL(s3c_adc_start);
 
-static void s3c_adc_default_select(unsigned select)
+static void s3c_convert_done(struct s3c_adc_client *client,
+			     unsigned v, unsigned u, unsigned *left)
+{
+	client->result = v;
+	wake_up(client->wait);
+}
+
+int s3c_adc_read(struct s3c_adc_client *client, unsigned int ch)
+{
+	DECLARE_WAIT_QUEUE_HEAD_ONSTACK(wake);
+	int ret;
+
+	client->convert_cb = s3c_convert_done;
+	client->wait = &wake;
+	client->result = -1;
+
+	ret = s3c_adc_start(client, ch, 1);
+	if (ret < 0)
+		goto err;
+
+	ret = wait_event_timeout(wake, client->result >= 0, HZ / 2);
+	if (client->result < 0) {
+		ret = -ETIMEDOUT;
+		goto err;
+	}
+
+	client->convert_cb = NULL;
+	return client->result;
+
+err:
+	return ret;
+}
+EXPORT_SYMBOL_GPL(s3c_adc_convert);
+
+static void s3c_adc_default_select(struct s3c_adc_client *client,
+				   unsigned select)
 {
 }
 
 struct s3c_adc_client *s3c_adc_register(struct platform_device *pdev,
-					void (*select)(unsigned int selected),
-					void (*conv)(unsigned d0, unsigned d1,
+					void (*select)(struct s3c_adc_client *client,
+						       unsigned int selected),
+					void (*conv)(struct s3c_adc_client *client,
+						     unsigned d0, unsigned d1,
 						     unsigned *samples_left),
 					unsigned int is_ts)
 {
 	struct s3c_adc_client *client;
 
 	WARN_ON(!pdev);
-	WARN_ON(!conv);
 
 	if (!select)
 		select = s3c_adc_default_select;
 
-	if (!conv || !pdev)
+	if (!pdev)
 		return ERR_PTR(-EINVAL);
 
 	client = kzalloc(sizeof(struct s3c_adc_client), GFP_KERNEL);
@@ -230,16 +269,19 @@ static irqreturn_t s3c_adc_irq(int irq, void *pw)
 	adc_dbg(adc, "read %d: 0x%04x, 0x%04x\n", client->nr_samples, data0, data1);
 
 	client->nr_samples--;
-	(client->convert_cb)(data0 & 0x3ff, data1 & 0x3ff, &client->nr_samples);
+
+	if (client->convert_cb)
+		(client->convert_cb)(client, data0 & 0x3ff, data1 & 0x3ff,
+				     &client->nr_samples);
 
 	if (client->nr_samples > 0) {
 		/* fire another conversion for this */
 
-		client->select_cb(1);
+		client->select_cb(client, 1);
 		s3c_adc_convert(adc);
 	} else {
 		local_irq_save(flags);
-		(client->select_cb)(0);
+		(client->select_cb)(client, 0);
 		adc->cur = NULL;
 
 		s3c_adc_try(adc);

arch/arm/plat-s3c24xx/cpu-freq-debugfs.c

+/* linux/arch/arm/plat-s3c24xx/cpu-freq-debugfs.c
+ *
+ * Copyright (c) 2009 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX CPU Frequency scaling - debugfs status support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/interrupt.h>
+#include <linux/ioport.h>
+#include <linux/cpufreq.h>
+#include <linux/debugfs.h>
+#include <linux/seq_file.h>
+#include <linux/err.h>
+
+#include <plat/cpu-freq-core.h>
+
+static struct dentry *dbgfs_root;
+static struct dentry *dbgfs_file_io;
+static struct dentry *dbgfs_file_info;
+static struct dentry *dbgfs_file_board;
+
+#define print_ns(x) ((x) / 10), ((x) % 10)
+
+static void show_max(struct seq_file *seq, struct s3c_freq *f)
+{
+	seq_printf(seq, "MAX: F=%lu, H=%lu, P=%lu, A=%lu\n",
+		   f->fclk, f->hclk, f->pclk, f->armclk);
+}
+
+static int board_show(struct seq_file *seq, void *p)
+{
+	struct s3c_cpufreq_config *cfg;
+	struct s3c_cpufreq_board *brd;
+
+	cfg = s3c_cpufreq_getconfig();
+	if (!cfg) {
+		seq_printf(seq, "no configuration registered\n");
+		return 0;
+	}
+
+	brd = cfg->board;
+	if (!brd) {
+		seq_printf(seq, "no board definition set?\n");
+		return 0;
+	}
+
+	seq_printf(seq, "SDRAM refresh %u ns\n", brd->refresh);
+	seq_printf(seq, "auto_io=%u\n", brd->auto_io);
+	seq_printf(seq, "need_io=%u\n", brd->need_io);
+
+	show_max(seq, &brd->max);
+
+
+	return 0;
+}
+
+static int fops_board_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, board_show, NULL);
+}
+
+static const struct file_operations fops_board = {
+	.open		= fops_board_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+	.owner		= THIS_MODULE,
+};
+
+static int info_show(struct seq_file *seq, void *p)
+{
+	struct s3c_cpufreq_config *cfg;
+
+	cfg = s3c_cpufreq_getconfig();
+	if (!cfg) {
+		seq_printf(seq, "no configuration registered\n");
+		return 0;
+	}
+
+	seq_printf(seq, "  FCLK %ld Hz\n", cfg->freq.fclk);
+	seq_printf(seq, "  HCLK %ld Hz (%lu.%lu ns)\n",
+		   cfg->freq.hclk, print_ns(cfg->freq.hclk_tns));
+	seq_printf(seq, "  PCLK %ld Hz\n", cfg->freq.hclk);
+	seq_printf(seq, "ARMCLK %ld Hz\n", cfg->freq.armclk);
+	seq_printf(seq, "\n");
+
+	show_max(seq, &cfg->max);
+
+	seq_printf(seq, "Divisors: P=%d, H=%d, A=%d, dvs=%s\n",
+		   cfg->divs.h_divisor, cfg->divs.p_divisor,
+		   cfg->divs.arm_divisor, cfg->divs.dvs ? "on" : "off");
+	seq_printf(seq, "\n");
+
+	seq_printf(seq, "lock_pll=%u\n", cfg->lock_pll);
+
+	return 0;
+}
+
+static int fops_info_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, info_show, NULL);
+}
+
+static const struct file_operations fops_info = {
+	.open		= fops_info_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+	.owner		= THIS_MODULE,
+};
+
+static int io_show(struct seq_file *seq, void *p)
+{
+	void (*show_bank)(struct seq_file *, struct s3c_cpufreq_config *, union s3c_iobank *);
+	struct s3c_cpufreq_config *cfg;
+	struct s3c_iotimings *iot;
+	union s3c_iobank *iob;
+	int bank;
+
+	cfg = s3c_cpufreq_getconfig();
+	if (!cfg) {
+		seq_printf(seq, "no configuration registered\n");
+		return 0;
+	}
+
+	show_bank = cfg->info->debug_io_show;
+	if (!show_bank) {
+		seq_printf(seq, "no code to show bank timing\n");
+		return 0;
+	}
+
+	iot = s3c_cpufreq_getiotimings();
+	if (!iot) {
+		seq_printf(seq, "no io timings registered\n");
+		return 0;
+	}
+
+	seq_printf(seq, "hclk period is %lu.%lu ns\n", print_ns(cfg->freq.hclk_tns));
+
+	for (bank = 0; bank < MAX_BANKS; bank++) {
+		iob = &iot->bank[bank];
+
+		seq_printf(seq, "bank %d: ", bank);
+
+		if (!iob->io_2410) {
+			seq_printf(seq, "nothing set\n");
+			continue;
+		}
+
+		show_bank(seq, cfg, iob);
+	}
+
+	return 0;
+}
+
+static int fops_io_open(struct inode *inode, struct file *file)
+{
+	return single_open(file, io_show, NULL);
+}
+
+static const struct file_operations fops_io = {
+	.open		= fops_io_open,
+	.read		= seq_read,
+	.llseek		= seq_lseek,
+	.release	= single_release,
+	.owner		= THIS_MODULE,
+};
+
+
+static int __init s3c_freq_debugfs_init(void)
+{
+	dbgfs_root = debugfs_create_dir("s3c-cpufreq", NULL);
+	if (IS_ERR(dbgfs_root)) {
+		printk(KERN_ERR "%s: error creating debugfs root\n", __func__);
+		return PTR_ERR(dbgfs_root);
+	}
+
+	dbgfs_file_io = debugfs_create_file("io-timing", S_IRUGO, dbgfs_root,
+					    NULL, &fops_io);
+
+	dbgfs_file_info = debugfs_create_file("info", S_IRUGO, dbgfs_root,
+					      NULL, &fops_info);
+
+	dbgfs_file_board = debugfs_create_file("board", S_IRUGO, dbgfs_root,
+					       NULL, &fops_board);
+
+	return 0;
+}
+
+late_initcall(s3c_freq_debugfs_init);
+

arch/arm/plat-s3c24xx/cpu.c

@@ -81,7 +81,7 @@ static struct cpu_table cpu_ids[] __initdata = {
 		.map_io		= s3c2410_map_io,
 		.init_clocks	= s3c2410_init_clocks,
 		.init_uarts	= s3c2410_init_uarts,
-		.init		= s3c2410_init,
+		.init		= s3c2410a_init,
 		.name		= name_s3c2410a
 	},
 	{

arch/arm/plat-s3c24xx/devs.c

@@ -26,6 +26,8 @@
 #include <asm/mach/irq.h>
 #include <mach/fb.h>
 #include <mach/hardware.h>
+#include <mach/dma.h>
+#include <mach/irqs.h>
 #include <asm/irq.h>
 
 #include <plat/regs-serial.h>
@@ -180,25 +182,6 @@ void __init s3c24xx_fb_set_platdata(struct s3c2410fb_mach_info *pd)
 	}
 }
 
-/* NAND Controller */
-
-static struct resource s3c_nand_resource[] = {
-	[0] = {
-		.start = S3C24XX_PA_NAND,
-		.end   = S3C24XX_PA_NAND + S3C24XX_SZ_NAND - 1,
-		.flags = IORESOURCE_MEM,
-	}
-};
-
-struct platform_device s3c_device_nand = {
-	.name		  = "s3c2410-nand",
-	.id		  = -1,
-	.num_resources	  = ARRAY_SIZE(s3c_nand_resource),
-	.resource	  = s3c_nand_resource,
-};
-
-EXPORT_SYMBOL(s3c_device_nand);
-
 /* USB Device (Gadget)*/
 
 static struct resource s3c_usbgadget_resource[] = {
@@ -348,7 +331,7 @@ struct platform_device s3c_device_adc = {
 /* HWMON */
 
 struct platform_device s3c_device_hwmon = {
-	.name		= "s3c24xx-hwmon",
+	.name		= "s3c-hwmon",
 	.id		= -1,
 	.dev.parent	= &s3c_device_adc.dev,
 };
@@ -473,4 +456,52 @@ struct platform_device s3c_device_camif = {
 
 EXPORT_SYMBOL(s3c_device_camif);
 
+/* AC97 */
+
+static struct resource s3c_ac97_resource[] = {
+	[0] = {
+		.start = S3C2440_PA_AC97,
+		.end   = S3C2440_PA_AC97 + S3C2440_SZ_AC97 -1,
+		.flags = IORESOURCE_MEM,
+	},
+	[1] = {
+		.start = IRQ_S3C244x_AC97,
+		.end   = IRQ_S3C244x_AC97,
+		.flags = IORESOURCE_IRQ,
+	},
+	[2] = {
+		.name  = "PCM out",
+		.start = DMACH_PCM_OUT,
+		.end   = DMACH_PCM_OUT,
+		.flags = IORESOURCE_DMA,
+	},
+	[3] = {
+		.name  = "PCM in",
+		.start = DMACH_PCM_IN,
+		.end   = DMACH_PCM_IN,
+		.flags = IORESOURCE_DMA,
+	},
+	[4] = {
+		.name  = "Mic in",
+		.start = DMACH_MIC_IN,
+		.end   = DMACH_MIC_IN,
+		.flags = IORESOURCE_DMA,
+	},
+};
+
+static u64 s3c_device_ac97_dmamask = 0xffffffffUL;
+
+struct platform_device s3c_device_ac97 = {
+	.name		  = "s3c-ac97",
+	.id		  = -1,
+	.num_resources	  = ARRAY_SIZE(s3c_ac97_resource),
+	.resource	  = s3c_ac97_resource,
+	.dev              = {
+		.dma_mask = &s3c_device_ac97_dmamask,
+		.coherent_dma_mask = 0xffffffffUL
+	}
+};
+
+EXPORT_SYMBOL(s3c_device_ac97);
+
 #endif // CONFIG_CPU_S32440

arch/arm/plat-s3c24xx/include/plat/fiq.h

+/* linux/include/asm-arm/plat-s3c24xx/fiq.h
+ *
+ * Copyright (c) 2009 Simtec Electronics
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * Header file for S3C24XX CPU FIQ support
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+extern int s3c24xx_set_fiq(unsigned int irq, bool on);

arch/arm/plat-s3c24xx/include/plat/s3c2410.h

@@ -14,6 +14,7 @@
 #ifdef CONFIG_CPU_S3C2410
 
 extern  int s3c2410_init(void);
+extern  int s3c2410a_init(void);
 
 extern void s3c2410_map_io(void);
 

arch/arm/plat-s3c24xx/irq.c

@@ -493,6 +493,38 @@ s3c_irq_demux_extint4t7(unsigned int irq,
 	}
 }
 
+#ifdef CONFIG_FIQ
+/**
+ * s3c24xx_set_fiq - set the FIQ routing
+ * @irq: IRQ number to route to FIQ on processor.
+ * @on: Whether to route @irq to the FIQ, or to remove the FIQ routing.
+ *
+ * Change the state of the IRQ to FIQ routing depending on @irq and @on. If
+ * @on is true, the @irq is checked to see if it can be routed and the
+ * interrupt controller updated to route the IRQ. If @on is false, the FIQ
+ * routing is cleared, regardless of which @irq is specified.
+ */
+int s3c24xx_set_fiq(unsigned int irq, bool on)
+{
+	u32 intmod;
+	unsigned offs;
+
+	if (on) {
+		offs = irq - FIQ_START;
+		if (offs > 31)
+			return -EINVAL;
+
+		intmod = 1 << offs;
+	} else {
+		intmod = 0;
+	}
+
+	__raw_writel(intmod, S3C2410_INTMOD);
+	return 0;
+}
+#endif
+
+
 /* s3c24xx_init_irq
  *
  * Initialise S3C2410 IRQ system
@@ -505,6 +537,10 @@ void __init s3c24xx_init_irq(void)
 	int irqno;
 	int i;
 
+#ifdef CONFIG_FIQ
+	init_FIQ();
+#endif
+
 	irqdbf("s3c2410_init_irq: clearing interrupt status flags\n");
 
 	/* first, clear all interrupts pending... */

arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c

+/* linux/arch/arm/plat-s3c24xx/s3c2410-cpufreq-utils.c
+ *
+ * Copyright (c) 2009 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX CPU Frequency scaling - utils for S3C2410/S3C2440/S3C2442
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+*/
+
+#include <linux/kernel.h>
+#include <linux/errno.h>
+#include <linux/cpufreq.h>
+#include <linux/io.h>
+
+#include <mach/map.h>
+#include <mach/regs-mem.h>
+#include <mach/regs-clock.h>
+
+#include <plat/cpu-freq-core.h>
+
+/**
+ * s3c2410_cpufreq_setrefresh - set SDRAM refresh value
+ * @cfg: The frequency configuration
+ *
+ * Set the SDRAM refresh value appropriately for the configured
+ * frequency.
+ */
+void s3c2410_cpufreq_setrefresh(struct s3c_cpufreq_config *cfg)
+{
+	struct s3c_cpufreq_board *board = cfg->board;
+	unsigned long refresh;
+	unsigned long refval;
+
+	/* Reduce both the refresh time (in ns) and the frequency (in MHz)
+	 * down to ensure that we do not overflow 32 bit numbers.
+	 *
+	 * This should work for HCLK up to 133MHz and refresh period up
+	 * to 30usec.
+	 */
+
+	refresh = (cfg->freq.hclk / 100) * (board->refresh / 10);
+	refresh = DIV_ROUND_UP(refresh, (1000 * 1000)); /* apply scale  */
+	refresh = (1 << 11) + 1 - refresh;
+
+	s3c_freq_dbg("%s: refresh value %lu\n", __func__, refresh);
+
+	refval = __raw_readl(S3C2410_REFRESH);
+	refval &= ~((1 << 12) - 1);
+	refval |= refresh;
+	__raw_writel(refval, S3C2410_REFRESH);
+}
+
+/**
+ * s3c2410_set_fvco - set the PLL value
+ * @cfg: The frequency configuration
+ */
+void s3c2410_set_fvco(struct s3c_cpufreq_config *cfg)
+{
+	__raw_writel(cfg->pll.index, S3C2410_MPLLCON);
+}

arch/arm/plat-s3c24xx/spi-bus1-gpd8_9_10.c

+/* linux/arch/arm/plat-s3c24xx/spi-bus0-gpd8_9_10.c
+ *
+ * Copyright (c) 2008 Simtec Electronics
+ *	http://armlinux.simtec.co.uk/
+ *	Ben Dooks <ben@simtec.co.uk>
+ *
+ * S3C24XX SPI - gpio configuration for bus 1 on gpd8,9,10
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License.
+*/
+
+#include <linux/kernel.h>
+#include <linux/gpio.h>
+
+#include <mach/spi.h>
+#include <mach/regs-gpio.h>
+
+void s3c24xx_spi_gpiocfg_bus1_gpd8_9_10(struct s3c2410_spi_info *spi,
+					int enable)
+{
+
+	printk(KERN_INFO "%s(%d)\n", __func__, enable);
+	if (enable) {
+		s3c2410_gpio_cfgpin(S3C2410_GPD(10), S3C2440_GPD10_SPICLK1);
+		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2440_GPD9_SPIMOSI1);
+		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2440_GPD8_SPIMISO1);
+		s3c2410_gpio_pullup(S3C2410_GPD(10), 0);
+		s3c2410_gpio_pullup(S3C2410_GPD(9), 0);
+	} else {
+		s3c2410_gpio_cfgpin(S3C2410_GPD(8), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_cfgpin(S3C2410_GPD(9), S3C2410_GPIO_INPUT);
+		s3c2410_gpio_pullup(S3C2410_GPD(10), 1);
+		s3c2410_gpio_pullup(S3C2410_GPD(9), 1);
+		s3c2410_gpio_pullup(S3C2410_GPD(8), 1);
+	}
+}