Commit 2c7c040c authored by Stefan Wahren's avatar Stefan Wahren Committed by Eric Anholt

ARM: dts: bcm2835: Add Raspberry Pi Zero W

The Raspberry Pi Zero W has the same components like the Zero plus
a Cypress CYW43438 wireless chip (wifi + bl).
Signed-off-by: default avatarStefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: default avatarEric Anholt <eric@anholt.net>
Reviewed-by: default avatarEric Anholt <eric@anholt.net>
parent 79c2a9d3
......@@ -73,7 +73,8 @@ dtb-$(CONFIG_ARCH_BCM2835) += \
bcm2835-rpi-a-plus.dtb \
bcm2836-rpi-2-b.dtb \
bcm2837-rpi-3-b.dtb \
bcm2835-rpi-zero.dtb
bcm2835-rpi-zero.dtb \
bcm2835-rpi-zero-w.dtb
dtb-$(CONFIG_ARCH_BCM_5301X) += \
bcm4708-asus-rt-ac56u.dtb \
bcm4708-asus-rt-ac68u.dtb \
......
/*
* Copyright (C) 2017 Stefan Wahren <stefan.wahren@i2se.com>
*
* The code contained herein is licensed under the GNU General Public
* License. You may obtain a copy of the GNU General Public License
* Version 2 or later at the following locations:
*
* http://www.opensource.org/licenses/gpl-license.html
* http://www.gnu.org/copyleft/gpl.html
*/
/dts-v1/;
#include "bcm2835.dtsi"
#include "bcm2835-rpi.dtsi"
#include "bcm283x-rpi-usb-host.dtsi"
/ {
compatible = "raspberrypi,model-zero-w", "brcm,bcm2835";
model = "Raspberry Pi Zero W";
/* Needed by firmware to properly init UARTs */
aliases {
uart0 = "/soc/serial@7e201000";
uart1 = "/soc/serial@7e215040";
serial0 = "/soc/serial@7e201000";
serial1 = "/soc/serial@7e215040";
};
leds {
act {
gpios = <&gpio 47 GPIO_ACTIVE_HIGH>;
};
};
wifi_pwrseq: wifi-pwrseq {
compatible = "mmc-pwrseq-simple";
pinctrl-names = "default";
pinctrl-0 = <&wl_on>;
reset-gpios = <&gpio 41 GPIO_ACTIVE_LOW>;
};
};
&gpio {
/*
* This is based on the official GPU firmware DT blob.
*
* Legend:
* "NC" = not connected (no rail from the SoC)
* "FOO" = GPIO line named "FOO" on the schematic
* "FOO_N" = GPIO line named "FOO" on schematic, active low
*/
gpio-line-names = "GPIO0",
"GPIO1",
"SDA1",
"SCL1",
"GPIO_GCLK",
"GPIO5",
"GPIO6",
"SPI_CE1_N",
"SPI_CE0_N",
"SPI_MISO",
"SPI_MOSI",
"SPI_SCLK",
"GPIO12",
"GPIO13",
/* Serial port */
"TXD0",
"RXD0",
"GPIO16",
"GPIO17",
"GPIO18",
"GPIO19",
"GPIO20",
"GPIO21",
"GPIO22",
"GPIO23",
"GPIO24",
"GPIO25",
"GPIO26",
"GPIO27",
"SDA0",
"SCL0",
"NC", /* GPIO30 */
"NC", /* GPIO31 */
"NC", /* GPIO32 */
"NC", /* GPIO33 */
"NC", /* GPIO34 */
"NC", /* GPIO35 */
"NC", /* GPIO36 */
"NC", /* GPIO37 */
"NC", /* GPIO38 */
"NC", /* GPIO39 */
"CAM_GPIO1", /* GPIO40 */
"WL_ON", /* GPIO41 */
"NC", /* GPIO42 */
"WIFI_CLK", /* GPIO43 */
"CAM_GPIO0", /* GPIO44 */
"BT_ON", /* GPIO45 */
"HDMI_HPD_N",
"STATUS_LED_N",
/* Used by SD Card */
"SD_CLK_R",
"SD_CMD_R",
"SD_DATA0_R",
"SD_DATA1_R",
"SD_DATA2_R",
"SD_DATA3_R";
pinctrl-0 = <&gpioout &alt0>;
wl_on: wl-on {
brcm,pins = <41>;
brcm,function = <BCM2835_FSEL_GPIO_OUT>;
};
};
&hdmi {
hpd-gpios = <&gpio 46 GPIO_ACTIVE_LOW>;
};
&sdhci {
#address-cells = <1>;
#size-cells = <0>;
pinctrl-0 = <&emmc_gpio34 &gpclk2_gpio43>;
mmc-pwrseq = <&wifi_pwrseq>;
non-removable;
status = "okay";
brcmf: wifi@1 {
reg = <1>;
compatible = "brcm,bcm4329-fmac";
};
};
&uart0 {
pinctrl-names = "default";
pinctrl-0 = <&uart0_gpio14>;
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment