Skip to content

L
linux
Commit 2ed25580 authored by Arnd Bergmann's avatar Arnd Bergmann
Browse files
Options

Merge tag 'omap-for-v4.2/clean' of... 

Merge tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/cleanup

Merge "Clean-up for omaps for v4.2 merge window" from Tony Lindgren:

Drop more omap3 legacy board-*.c files for v4.2. This time we're
dropping the board files for beagle, overo and cm-t35.

The reason for dropping these now rather than later is that now
we can simply revert the patches in case of unexpected issues as
we are not dropping any platform data at this point.

This leaves us with only the following board-*.c files:

BOARD                   REASON NEEDED
board-ldp.c             Still used in RMKs boot test system
board-omap3logic.c      Getting a .dts file for v4.2
board-omap3pandora.c    Got a .dts file for v4.1
board-rx51-*.c          Needs /proc/atags support for user space

I'm hoping we can drop the remaining board-*.c for v4.3 merge
window, then keep the platform data around for one more merge
window in case of reverting needed, then drop the platform data
too for v4.4 if no issues needing reverting are found.

Also, few patches to clean-up the usage of Linux generic
macros:

- Use define for console loglevel

- Use const for struct irq_domain_ops

- Use PTR_ERR_OR_ZERO instead of PTR_RET

* tag 'omap-for-v4.2/clean' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
  mach-omap2: Remove use of deprecated marco, PTR_RET in devices.c
  ARM: OMAP2+: Remove calls to deprecacted marco,PTR_RET in the files,fb.c and pmu.c
  ARM: OMAP2+: Constify irq_domain_ops
  ARM: OMAP2+: use symbolic defines for console loglevels instead of numbers
  ARM: OMAP2+: Remove legacy booting support for Beagleboards
  ARM: OMAP2+: Remove legacy booting support for Overo
  ARM: OMAP2+: Remove legacy booting support for cm-t35
parents cbdf76ab fd0dbc83
Show whitespace changes
Inline Side-by-side
Showing with 6 additions and 1966 deletions
arch/arm/mach-omap2/Kconfig
View file @ 2ed25580
......@@ -171,12 +171,6 @@ config MACH_OMAP2_TUSB6010
depends on ARCH_OMAP2 && SOC_OMAP2420
default y if MACH_NOKIA_N8X0
config MACH_OMAP3_BEAGLE
bool "OMAP3 BEAGLE board"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
config MACH_OMAP_LDP
bool "OMAP3 LDP board"
depends on ARCH_OMAP3
......@@ -203,12 +197,6 @@ config MACH_OMAP3_TORPEDO
for full description please see the products webpage at
http://www.logicpd.com/products/development-kits/zoom-omap35x-torpedo-development-kit
config MACH_OVERO
bool "Gumstix Overo board"
depends on ARCH_OMAP3
default y
select OMAP_PACKAGE_CBB
config MACH_OMAP3517EVM
bool "OMAP3517/ AM3517 EVM board"
depends on ARCH_OMAP3
......@@ -240,16 +228,6 @@ config MACH_NOKIA_RX51
default y
select OMAP_PACKAGE_CBB
config MACH_CM_T35
bool "CompuLab CM-T35/CM-T3730 modules"
depends on ARCH_OMAP3
default y
select MACH_CM_T3730
select OMAP_PACKAGE_CUS
config MACH_CM_T3730
bool
config OMAP3_SDRC_AC_TIMING
bool "Enable SDRC AC timing register changes"
depends on ARCH_OMAP3
......
arch/arm/mach-omap2/Makefile
View file @ 2ed25580
......@@ -242,17 +242,14 @@ obj-$(CONFIG_SOC_OMAP2420) += msdi.o
# Specific board support
obj-$(CONFIG_MACH_OMAP_GENERIC) += board-generic.o pdata-quirks.o
obj-$(CONFIG_MACH_OMAP3_BEAGLE) += board-omap3beagle.o
obj-$(CONFIG_MACH_OMAP_LDP) += board-ldp.o
obj-$(CONFIG_MACH_OMAP3530_LV_SOM) += board-omap3logic.o
obj-$(CONFIG_MACH_OMAP3_TORPEDO) += board-omap3logic.o
obj-$(CONFIG_MACH_OVERO) += board-overo.o
obj-$(CONFIG_MACH_OMAP3_PANDORA) += board-omap3pandora.o
obj-$(CONFIG_MACH_NOKIA_N8X0) += board-n8x0.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51.o sdram-nokia.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-peripherals.o
obj-$(CONFIG_MACH_NOKIA_RX51) += board-rx51-video.o
obj-$(CONFIG_MACH_CM_T35) += board-cm-t35.o
# Platform specific device init code
......
arch/arm/mach-omap2/board-cm-t35.c deleted 100644 → 0
View file @ cbdf76ab
/*
* CompuLab CM-T35/CM-T3730 modules support
*
* Copyright (C) 2009-2011 CompuLab, Ltd.
* Authors: Mike Rapoport <mike@compulab.co.il>
* Igor Grinberg <grinberg@compulab.co.il>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
*/
#include <linux/clk-provider.h>
#include <linux/clkdev.h>
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/input.h>
#include <linux/input/matrix_keypad.h>
#include <linux/delay.h>
#include <linux/gpio.h>
#include <linux/omap-gpmc.h>
#include <linux/platform_data/gpio-omap.h>
#include <linux/platform_data/at24.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/fixed.h>
#include <linux/regulator/machine.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/spi/spi.h>
#include <linux/spi/tdo24m.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include "common.h"
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "hsmmc.h"
#include "common-board-devices.h"
#define CM_T35_GPIO_PENDOWN 57
#define SB_T35_USB_HUB_RESET_GPIO 167
#define CM_T35_SMSC911X_CS 5
#define CM_T35_SMSC911X_GPIO 163
#define SB_T35_SMSC911X_CS 4
#define SB_T35_SMSC911X_GPIO 65
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
#include "gpmc-smsc911x.h"
static struct omap_smsc911x_platform_data cm_t35_smsc911x_cfg = {
.id = 0,
.cs = CM_T35_SMSC911X_CS,
.gpio_irq = CM_T35_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static struct omap_smsc911x_platform_data sb_t35_smsc911x_cfg = {
.id = 1,
.cs = SB_T35_SMSC911X_CS,
.gpio_irq = SB_T35_SMSC911X_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT | SMSC911X_SAVE_MAC_ADDRESS,
};
static struct regulator_consumer_supply cm_t35_smsc911x_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
};
static struct regulator_consumer_supply sb_t35_smsc911x_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
};
static void __init cm_t35_init_ethernet(void)
{
regulator_register_fixed(0, cm_t35_smsc911x_supplies,
ARRAY_SIZE(cm_t35_smsc911x_supplies));
regulator_register_fixed(1, sb_t35_smsc911x_supplies,
ARRAY_SIZE(sb_t35_smsc911x_supplies));
gpmc_smsc911x_init(&cm_t35_smsc911x_cfg);
gpmc_smsc911x_init(&sb_t35_smsc911x_cfg);
}
#else
static inline void __init cm_t35_init_ethernet(void) { return; }
#endif
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
static struct gpio_led cm_t35_leds[] = {
[0] = {
.gpio = 186,
.name = "cm-t35:green",
.default_trigger = "heartbeat",
.active_low = 0,
},
};
static struct gpio_led_platform_data cm_t35_led_pdata = {
.num_leds = ARRAY_SIZE(cm_t35_leds),
.leds = cm_t35_leds,
};
static struct platform_device cm_t35_led_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &cm_t35_led_pdata,
},
};
static void __init cm_t35_init_led(void)
{
platform_device_register(&cm_t35_led_device);
}
#else
static inline void cm_t35_init_led(void) {}
#endif
#if defined(CONFIG_MTD_NAND_OMAP2) || defined(CONFIG_MTD_NAND_OMAP2_MODULE)
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
static struct mtd_partition cm_t35_nand_partitions[] = {
{
.name = "xloader",
.offset = 0, /* Offset = 0x00000 */
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE
},
{
.name = "uboot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 15 * NAND_BLOCK_SIZE,
},
{
.name = "uboot environment",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
.size = 2 * NAND_BLOCK_SIZE,
},
{
.name = "linux",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x2A0000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x6A0000 */
.size = MTDPART_SIZ_FULL,
},
};
static struct omap_nand_platform_data cm_t35_nand_data = {
.parts = cm_t35_nand_partitions,
.nr_parts = ARRAY_SIZE(cm_t35_nand_partitions),
.cs = 0,
};
static void __init cm_t35_init_nand(void)
{
if (gpmc_nand_init(&cm_t35_nand_data, NULL) < 0)
pr_err("CM-T35: Unable to register NAND device\n");
}
#else
static inline void cm_t35_init_nand(void) {}
#endif
#define CM_T35_LCD_EN_GPIO 157
#define CM_T35_LCD_BL_GPIO 58
#define CM_T35_DVI_EN_GPIO 54
static const struct display_timing cm_t35_lcd_videomode = {
.pixelclock = { 0, 26000000, 0 },
.hactive = { 0, 480, 0 },
.hfront_porch = { 0, 104, 0 },
.hback_porch = { 0, 8, 0 },
.hsync_len = { 0, 8, 0 },
.vactive = { 0, 640, 0 },
.vfront_porch = { 0, 4, 0 },
.vback_porch = { 0, 2, 0 },
.vsync_len = { 0, 2, 0 },
.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_NEGEDGE,
};
static struct panel_dpi_platform_data cm_t35_lcd_pdata = {
.name = "lcd",
.source = "dpi.0",
.data_lines = 18,
.display_timing = &cm_t35_lcd_videomode,
.enable_gpio = -1,
.backlight_gpio = CM_T35_LCD_BL_GPIO,
};
static struct platform_device cm_t35_lcd_device = {
.name = "panel-dpi",
.id = 0,
.dev.platform_data = &cm_t35_lcd_pdata,
};
static struct connector_dvi_platform_data cm_t35_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = -1,
};
static struct platform_device cm_t35_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &cm_t35_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data cm_t35_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = CM_T35_DVI_EN_GPIO,
};
static struct platform_device cm_t35_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &cm_t35_tfp410_pdata,
};
static struct connector_atv_platform_data cm_t35_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device cm_t35_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &cm_t35_tv_pdata,
};
static struct omap_dss_board_info cm_t35_dss_data = {
.default_display_name = "dvi",
};
static struct omap2_mcspi_device_config tdo24m_mcspi_config = {
.turbo_mode = 0,
};
static struct tdo24m_platform_data tdo24m_config = {
.model = TDO35S,
};
static struct spi_board_info cm_t35_lcd_spi_board_info[] __initdata = {
{
.modalias = "tdo24m",
.bus_num = 4,
.chip_select = 0,
.max_speed_hz = 1000000,
.controller_data = &tdo24m_mcspi_config,
.platform_data = &tdo24m_config,
},
};
static void __init cm_t35_init_display(void)
{
int err;
spi_register_board_info(cm_t35_lcd_spi_board_info,
ARRAY_SIZE(cm_t35_lcd_spi_board_info));
err = gpio_request_one(CM_T35_LCD_EN_GPIO, GPIOF_OUT_INIT_LOW,
"lcd bl enable");
if (err) {
pr_err("CM-T35: failed to request LCD EN GPIO\n");
return;
}
msleep(50);
gpio_set_value(CM_T35_LCD_EN_GPIO, 1);
err = omap_display_init(&cm_t35_dss_data);
if (err) {
pr_err("CM-T35: failed to register DSS device\n");
gpio_free(CM_T35_LCD_EN_GPIO);
}
platform_device_register(&cm_t35_tfp410_device);
platform_device_register(&cm_t35_dvi_connector_device);
platform_device_register(&cm_t35_lcd_device);
platform_device_register(&cm_t35_tv_connector_device);
}
static struct regulator_consumer_supply cm_t35_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
static struct regulator_consumer_supply cm_t35_vsim_supply[] = {
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
};
static struct regulator_consumer_supply cm_t35_vio_supplies[] = {
REGULATOR_SUPPLY("vcc", "spi1.0"),
REGULATOR_SUPPLY("vdds_dsi", "omapdss"),
REGULATOR_SUPPLY("vdds_dsi", "omapdss_dpi.0"),
REGULATOR_SUPPLY("vdds_dsi", "omapdss_dsi.0"),
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data cm_t35_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(cm_t35_vmmc1_supply),
.consumer_supplies = cm_t35_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data cm_t35_vsim = {
.constraints = {
.min_uV = 1800000,
.max_uV = 3000000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(cm_t35_vsim_supply),
.consumer_supplies = cm_t35_vsim_supply,
};
static struct regulator_init_data cm_t35_vio = {
.constraints = {
.min_uV = 1800000,
.max_uV = 1800000,
.apply_uV = true,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_MODE,
},
.num_consumer_supplies = ARRAY_SIZE(cm_t35_vio_supplies),
.consumer_supplies = cm_t35_vio_supplies,
};
static uint32_t cm_t35_keymap[] = {
KEY(0, 0, KEY_A), KEY(0, 1, KEY_B), KEY(0, 2, KEY_LEFT),
KEY(1, 0, KEY_UP), KEY(1, 1, KEY_ENTER), KEY(1, 2, KEY_DOWN),
KEY(2, 0, KEY_RIGHT), KEY(2, 1, KEY_C), KEY(2, 2, KEY_D),
};
static struct matrix_keymap_data cm_t35_keymap_data = {
.keymap = cm_t35_keymap,
.keymap_size = ARRAY_SIZE(cm_t35_keymap),
};
static struct twl4030_keypad_data cm_t35_kp_data = {
.keymap_data = &cm_t35_keymap_data,
.rows = 3,
.cols = 3,
.rep = 1,
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.deferred = true,
},
{
.mmc = 2,
.caps = MMC_CAP_4_BIT_DATA,
.transceiver = 1,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.ocr_mask = 0x00100000, /* 3.3V */
},
{} /* Terminator */
};
static struct usbhs_phy_data phy_data[] __initdata = {
{
.port = 1,
.reset_gpio = OMAP_MAX_GPIO_LINES + 6,
.vcc_gpio = -EINVAL,
},
{
.port = 2,
.reset_gpio = OMAP_MAX_GPIO_LINES + 7,
.vcc_gpio = -EINVAL,
},
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[0] = OMAP_EHCI_PORT_MODE_PHY,
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
static void __init cm_t35_init_usbh(void)
{
int err;
err = gpio_request_one(SB_T35_USB_HUB_RESET_GPIO,
GPIOF_OUT_INIT_LOW, "usb hub rst");
if (err) {
pr_err("SB-T35: usb hub rst gpio request failed: %d\n", err);
} else {
udelay(10);
gpio_set_value(SB_T35_USB_HUB_RESET_GPIO, 1);
msleep(1);
}
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
}
static int cm_t35_twl_gpio_setup(struct device *dev, unsigned gpio,
unsigned ngpio)
{
int wlan_rst = gpio + 2;
if (gpio_request_one(wlan_rst, GPIOF_OUT_INIT_HIGH, "WLAN RST") == 0) {
gpio_export(wlan_rst, 0);
udelay(10);
gpio_set_value_cansleep(wlan_rst, 0);
udelay(10);
gpio_set_value_cansleep(wlan_rst, 1);
} else {
pr_err("CM-T35: could not obtain gpio for WiFi reset\n");
}
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap_hsmmc_late_init(mmc);
return 0;
}
static struct twl4030_gpio_platform_data cm_t35_gpio_data = {
.setup = cm_t35_twl_gpio_setup,
};
static struct twl4030_power_data cm_t35_power_data = {
.use_poweroff = true,
};
static struct twl4030_platform_data cm_t35_twldata = {
/* platform_data for children goes here */
.keypad = &cm_t35_kp_data,
.gpio = &cm_t35_gpio_data,
.vmmc1 = &cm_t35_vmmc1,
.vsim = &cm_t35_vsim,
.vio = &cm_t35_vio,
.power = &cm_t35_power_data,
};
#if defined(CONFIG_VIDEO_OMAP3) || defined(CONFIG_VIDEO_OMAP3_MODULE)
#include <media/omap3isp.h>
#include "devices.h"
static struct isp_platform_subdev cm_t35_isp_subdevs[] = {
{
.board_info = &(struct i2c_board_info){
I2C_BOARD_INFO("mt9t001", 0x5d)
},
.i2c_adapter_id = 3,
.bus = &(struct isp_bus_cfg){
.interface = ISP_INTERFACE_PARALLEL,
.bus = {
.parallel = {
.clk_pol = 1,
},
},
},
},
{
.board_info = &(struct i2c_board_info){
I2C_BOARD_INFO("tvp5150", 0x5c),
},
.i2c_adapter_id = 3,
.bus = &(struct isp_bus_cfg){
.interface = ISP_INTERFACE_PARALLEL,
.bus = {
.parallel = {
.clk_pol = 0,
},
},
},
},
{ 0 },
};
static struct isp_platform_data cm_t35_isp_pdata = {
.subdevs = cm_t35_isp_subdevs,
};
static struct regulator_consumer_supply cm_t35_camera_supplies[] = {
REGULATOR_SUPPLY("vaa", "3-005d"),
REGULATOR_SUPPLY("vdd", "3-005d"),
};
static void __init cm_t35_init_camera(void)
{
struct clk *clk;
clk = clk_register_fixed_rate(NULL, "mt9t001-clkin", NULL, CLK_IS_ROOT,
48000000);
clk_register_clkdev(clk, NULL, "3-005d");
regulator_register_fixed(2, cm_t35_camera_supplies,
ARRAY_SIZE(cm_t35_camera_supplies));
if (omap3_init_camera(&cm_t35_isp_pdata) < 0)
pr_warn("CM-T3x: Failed registering camera device!\n");
}
#else
static inline void cm_t35_init_camera(void) {}
#endif /* CONFIG_VIDEO_OMAP3 */
static void __init cm_t35_init_i2c(void)
{
omap3_pmic_get_config(&cm_t35_twldata, TWL_COMMON_PDATA_USB,
TWL_COMMON_REGULATOR_VDAC |
TWL_COMMON_PDATA_AUDIO);
omap3_pmic_init("tps65930", &cm_t35_twldata);
omap_register_i2c_bus(3, 400, NULL, 0);
}
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
/* nCS and IRQ for CM-T35 ethernet */
OMAP3_MUX(GPMC_NCS5, OMAP_MUX_MODE0),
OMAP3_MUX(UART3_CTS_RCTX, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
/* nCS and IRQ for SB-T35 ethernet */
OMAP3_MUX(GPMC_NCS4, OMAP_MUX_MODE0),
OMAP3_MUX(GPMC_WAIT3, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLUP),
/* PENDOWN GPIO */
OMAP3_MUX(GPMC_NCS6, OMAP_MUX_MODE4 | OMAP_PIN_INPUT),
/* mUSB */
OMAP3_MUX(HSUSB0_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_STP, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(HSUSB0_DIR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_NXT, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(HSUSB0_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
/* MMC 2 */
OMAP3_MUX(SDMMC2_DAT4, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
OMAP3_MUX(SDMMC2_DAT5, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
OMAP3_MUX(SDMMC2_DAT6, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
OMAP3_MUX(SDMMC2_DAT7, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
/* McSPI 1 */
OMAP3_MUX(MCSPI1_CLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCSPI1_SIMO, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCSPI1_SOMI, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCSPI1_CS0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
/* McSPI 4 */
OMAP3_MUX(MCBSP1_CLKR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_DX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_DR, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP1_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT_PULLUP),
/* McBSP 2 */
OMAP3_MUX(MCBSP2_FSX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP2_CLKX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP2_DR, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(MCBSP2_DX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
/* serial ports */
OMAP3_MUX(MCBSP3_CLKX, OMAP_MUX_MODE1 | OMAP_PIN_OUTPUT),
OMAP3_MUX(MCBSP3_FSX, OMAP_MUX_MODE1 | OMAP_PIN_INPUT),
OMAP3_MUX(UART1_TX, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(UART1_RX, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
/* common DSS */
OMAP3_MUX(DSS_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_HSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_VSYNC, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_ACBIAS, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA6, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA7, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA8, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA9, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA10, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA11, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA12, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA13, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA14, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA15, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA16, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
OMAP3_MUX(DSS_DATA17, OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT),
/* Camera */
OMAP3_MUX(CAM_HS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_VS, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_XCLKA, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_PCLK, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_FLD, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D0, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D1, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D2, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D3, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D4, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D5, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D6, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D7, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D8, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
OMAP3_MUX(CAM_D9, OMAP_MUX_MODE0 | OMAP_PIN_INPUT_PULLDOWN),
OMAP3_MUX(CAM_STROBE, OMAP_MUX_MODE0 | OMAP_PIN_INPUT),
OMAP3_MUX(CAM_D10, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
OMAP3_MUX(CAM_D11, OMAP_MUX_MODE4 | OMAP_PIN_INPUT_PULLDOWN),
/* display controls */
OMAP3_MUX(MCBSP1_FSR, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
OMAP3_MUX(GPMC_NCS7, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
OMAP3_MUX(GPMC_NCS3, OMAP_MUX_MODE4 | OMAP_PIN_OUTPUT),
/* TPS IRQ */
OMAP3_MUX(SYS_NIRQ, OMAP_MUX_MODE0 | OMAP_WAKEUP_EN | \
OMAP_PIN_INPUT_PULLUP),
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
static void __init cm_t3x_common_dss_mux_init(int mux_mode)
{
omap_mux_init_signal("dss_data18", mux_mode);
omap_mux_init_signal("dss_data19", mux_mode);
omap_mux_init_signal("dss_data20", mux_mode);
omap_mux_init_signal("dss_data21", mux_mode);
omap_mux_init_signal("dss_data22", mux_mode);
omap_mux_init_signal("dss_data23", mux_mode);
}
static void __init cm_t35_init_mux(void)
{
int mux_mode = OMAP_MUX_MODE0 | OMAP_PIN_OUTPUT;
omap_mux_init_signal("dss_data0.dss_data0", mux_mode);
omap_mux_init_signal("dss_data1.dss_data1", mux_mode);
omap_mux_init_signal("dss_data2.dss_data2", mux_mode);
omap_mux_init_signal("dss_data3.dss_data3", mux_mode);
omap_mux_init_signal("dss_data4.dss_data4", mux_mode);
omap_mux_init_signal("dss_data5.dss_data5", mux_mode);
cm_t3x_common_dss_mux_init(mux_mode);
}
static void __init cm_t3730_init_mux(void)
{
int mux_mode = OMAP_MUX_MODE3 | OMAP_PIN_OUTPUT;
omap_mux_init_signal("sys_boot0", mux_mode);
omap_mux_init_signal("sys_boot1", mux_mode);
omap_mux_init_signal("sys_boot3", mux_mode);
omap_mux_init_signal("sys_boot4", mux_mode);
omap_mux_init_signal("sys_boot5", mux_mode);
omap_mux_init_signal("sys_boot6", mux_mode);
cm_t3x_common_dss_mux_init(mux_mode);
}
#else
static inline void cm_t35_init_mux(void) {}
static inline void cm_t3730_init_mux(void) {}
#endif
static void __init cm_t3x_common_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CUS);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
omap_hsmmc_init(mmc);
cm_t35_init_i2c();
omap_ads7846_init(1, CM_T35_GPIO_PENDOWN, 0, NULL);
cm_t35_init_ethernet();
cm_t35_init_led();
cm_t35_init_display();
omap_twl4030_audio_init("cm-t3x", NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
cm_t35_init_usbh();
cm_t35_init_camera();
}
static void __init cm_t35_init(void)
{
cm_t3x_common_init();
cm_t35_init_mux();
cm_t35_init_nand();
}
static void __init cm_t3730_init(void)
{
cm_t3x_common_init();
cm_t3730_init_mux();
}
MACHINE_START(CM_T35, "Compulab CM-T35")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap35xx_init_early,
.init_irq = omap3_init_irq,
.init_machine = cm_t35_init,
.init_late = omap35xx_init_late,
.init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
MACHINE_START(CM_T3730, "Compulab CM-T3730")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3630_init_early,
.init_irq = omap3_init_irq,
.init_machine = cm_t3730_init,
.init_late = omap3630_init_late,
.init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
arch/arm/mach-omap2/board-omap3beagle.c deleted 100644 → 0
View file @ cbdf76ab
/*
* linux/arch/arm/mach-omap2/board-omap3beagle.c
*
* Copyright (C) 2008 Texas Instruments
*
* Modified from mach-omap2/board-3430sdp.c
*
* Initial code: Syed Mohammed Khasim
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/kernel.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/clk.h>
#include <linux/io.h>
#include <linux/leds.h>
#include <linux/pwm.h>
#include <linux/leds_pwm.h>
#include <linux/gpio.h>
#include <linux/input.h>
#include <linux/gpio_keys.h>
#include <linux/pm_opp.h>
#include <linux/cpu.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/partitions.h>
#include <linux/mtd/nand.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/regulator/machine.h>
#include <linux/i2c/twl.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/map.h>
#include <asm/mach/flash.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include "common.h"
#include "omap_device.h"
#include "gpmc.h"
#include "soc.h"
#include "mux.h"
#include "hsmmc.h"
#include "pm.h"
#include "board-flash.h"
#include "common-board-devices.h"
#define NAND_CS 0
static struct pwm_lookup pwm_lookup[] = {
/* LEDB -> PMU_STAT */
PWM_LOOKUP("twl-pwmled", 1, "leds_pwm", "beagleboard::pmu_stat",
7812500, PWM_POLARITY_NORMAL),
};
static struct led_pwm pwm_leds[] = {
{
.name = "beagleboard::pmu_stat",
.max_brightness = 127,
.pwm_period_ns = 7812500,
},
};
static struct led_pwm_platform_data pwm_data = {
.num_leds = ARRAY_SIZE(pwm_leds),
.leds = pwm_leds,
};
static struct platform_device leds_pwm = {
.name = "leds_pwm",
.id = -1,
.dev = {
.platform_data = &pwm_data,
},
};
/*
* OMAP3 Beagle revision
* Run time detection of Beagle revision is done by reading GPIO.
* GPIO ID -
* AXBX = GPIO173, GPIO172, GPIO171: 1 1 1
* C1_3 = GPIO173, GPIO172, GPIO171: 1 1 0
* C4 = GPIO173, GPIO172, GPIO171: 1 0 1
* XMA/XMB = GPIO173, GPIO172, GPIO171: 0 0 0
* XMC = GPIO173, GPIO172, GPIO171: 0 1 0
*/
enum {
OMAP3BEAGLE_BOARD_UNKN = 0,
OMAP3BEAGLE_BOARD_AXBX,
OMAP3BEAGLE_BOARD_C1_3,
OMAP3BEAGLE_BOARD_C4,
OMAP3BEAGLE_BOARD_XM,
OMAP3BEAGLE_BOARD_XMC,
};
static u8 omap3_beagle_version;
/*
* Board-specific configuration
* Defaults to BeagleBoard-xMC
*/
static struct {
int mmc1_gpio_wp;
bool usb_pwr_level; /* 0 - Active Low, 1 - Active High */
int dvi_pd_gpio;
int usr_button_gpio;
int mmc_caps;
} beagle_config = {
.mmc1_gpio_wp = -EINVAL,
.usb_pwr_level = 0,
.dvi_pd_gpio = -EINVAL,
.usr_button_gpio = 4,
.mmc_caps = MMC_CAP_4_BIT_DATA | MMC_CAP_8_BIT_DATA,
};
static struct gpio omap3_beagle_rev_gpios[] __initdata = {
{ 171, GPIOF_IN, "rev_id_0" },
{ 172, GPIOF_IN, "rev_id_1" },
{ 173, GPIOF_IN, "rev_id_2" },
};
static void __init omap3_beagle_init_rev(void)
{
int ret;
u16 beagle_rev = 0;
omap_mux_init_gpio(171, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(172, OMAP_PIN_INPUT_PULLUP);
omap_mux_init_gpio(173, OMAP_PIN_INPUT_PULLUP);
ret = gpio_request_array(omap3_beagle_rev_gpios,
ARRAY_SIZE(omap3_beagle_rev_gpios));
if (ret < 0) {
printk(KERN_ERR "Unable to get revision detection GPIO pins\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
return;
}
beagle_rev = gpio_get_value(171) | (gpio_get_value(172) << 1)
| (gpio_get_value(173) << 2);
gpio_free_array(omap3_beagle_rev_gpios,
ARRAY_SIZE(omap3_beagle_rev_gpios));
switch (beagle_rev) {
case 7:
printk(KERN_INFO "OMAP3 Beagle Rev: Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_AXBX;
beagle_config.mmc1_gpio_wp = 29;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 6:
printk(KERN_INFO "OMAP3 Beagle Rev: C1/C2/C3\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C1_3;
beagle_config.mmc1_gpio_wp = 23;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 5:
printk(KERN_INFO "OMAP3 Beagle Rev: C4\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_C4;
beagle_config.mmc1_gpio_wp = 23;
beagle_config.dvi_pd_gpio = 170;
beagle_config.usr_button_gpio = 7;
break;
case 0:
printk(KERN_INFO "OMAP3 Beagle Rev: xM Ax/Bx\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XM;
beagle_config.usb_pwr_level = 1;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
case 2:
printk(KERN_INFO "OMAP3 Beagle Rev: xM C\n");
omap3_beagle_version = OMAP3BEAGLE_BOARD_XMC;
beagle_config.mmc_caps &= ~MMC_CAP_8_BIT_DATA;
break;
default:
printk(KERN_INFO "OMAP3 Beagle Rev: unknown %hd\n", beagle_rev);
omap3_beagle_version = OMAP3BEAGLE_BOARD_UNKN;
}
}
static struct mtd_partition omap3beagle_nand_partitions[] = {
/* All the partition sizes are listed in terms of NAND block size */
{
.name = "X-Loader",
.offset = 0,
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
{
.name = "U-Boot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 15 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE, /* force read-only */
},
{
.name = "U-Boot Env",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x260000 */
.size = 1 * NAND_BLOCK_SIZE,
},
{
.name = "Kernel",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "File System",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
.size = MTDPART_SIZ_FULL,
},
};
/* DSS */
static struct connector_dvi_platform_data beagle_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = 3,
};
static struct platform_device beagle_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &beagle_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data beagle_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = -1,
};
static struct platform_device beagle_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &beagle_tfp410_pdata,
};
static struct connector_atv_platform_data beagle_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device beagle_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &beagle_tv_pdata,
};
static struct omap_dss_board_info beagle_dss_data = {
.default_display_name = "dvi",
};
#include "sdram-micron-mt46h32m32lf-6.h"
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_wp = -EINVAL,
.deferred = true,
},
{} /* Terminator */
};
static struct regulator_consumer_supply beagle_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
static struct regulator_consumer_supply beagle_vsim_supply[] = {
REGULATOR_SUPPLY("vmmc_aux", "omap_hsmmc.0"),
};
static struct gpio_led gpio_leds[];
static struct usbhs_phy_data phy_data[] = {
{
.port = 2,
.reset_gpio = 147,
.vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */
.vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */
},
};
static int beagle_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
int r;
mmc[0].gpio_wp = beagle_config.mmc1_gpio_wp;
/* gpio + 0 is "mmc0_cd" (input/IRQ) */
mmc[0].gpio_cd = gpio + 0;
omap_hsmmc_late_init(mmc);
/*
* TWL4030_GPIO_MAX + 0 == ledA, EHCI nEN_USB_PWR (out, XM active
* high / others active low)
* DVI reset GPIO is different between beagle revisions
*/
/* Valid for all -xM revisions */
if (cpu_is_omap3630()) {
/*
* gpio + 1 on Xm controls the TFP410's enable line (active low)
* gpio + 2 control varies depending on the board rev as below:
* P7/P8 revisions(prototype): Camera EN
* A2+ revisions (production): LDO (DVI, serial, led blocks)
*/
r = gpio_request_one(gpio + 1, GPIOF_OUT_INIT_LOW,
"nDVI_PWR_EN");
if (r)
pr_err("%s: unable to configure nDVI_PWR_EN\n",
__func__);
beagle_config.dvi_pd_gpio = gpio + 2;
} else {
/*
* REVISIT: need ehci-omap hooks for external VBUS
* power switch and overcurrent detect
*/
if (gpio_request_one(gpio + 1, GPIOF_IN, "EHCI_nOC"))
pr_err("%s: unable to configure EHCI_nOC\n", __func__);
}
beagle_tfp410_pdata.power_down_gpio = beagle_config.dvi_pd_gpio;
platform_device_register(&beagle_tfp410_device);
platform_device_register(&beagle_dvi_connector_device);
platform_device_register(&beagle_tv_connector_device);
/* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */
phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX;
phy_data[0].vcc_polarity = beagle_config.usb_pwr_level;
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
return 0;
}
static struct twl4030_gpio_platform_data beagle_gpio_data = {
.use_leds = true,
.pullups = BIT(1),
.pulldowns = BIT(2) | BIT(6) | BIT(7) | BIT(8) | BIT(13)
| BIT(15) | BIT(16) | BIT(17),
.setup = beagle_twl_gpio_setup,
};
/* VMMC1 for MMC1 pins CMD, CLK, DAT0..DAT3 (20 mA, plus card == max 220 mA) */
static struct regulator_init_data beagle_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(beagle_vmmc1_supply),
.consumer_supplies = beagle_vmmc1_supply,
};
/* VSIM for MMC1 pins DAT4..DAT7 (2 mA, plus card == max 50 mA) */
static struct regulator_init_data beagle_vsim = {
.constraints = {
.min_uV = 1800000,
.max_uV = 3000000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(beagle_vsim_supply),
.consumer_supplies = beagle_vsim_supply,
};
static struct twl4030_platform_data beagle_twldata = {
/* platform_data for children goes here */
.gpio = &beagle_gpio_data,
.vmmc1 = &beagle_vmmc1,
.vsim = &beagle_vsim,
};
static struct i2c_board_info __initdata beagle_i2c_eeprom[] = {
{
I2C_BOARD_INFO("eeprom", 0x50),
},
};
static int __init omap3_beagle_i2c_init(void)
{
omap3_pmic_get_config(&beagle_twldata,
TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_MADC |
TWL_COMMON_PDATA_AUDIO,
TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
beagle_twldata.vpll2->constraints.name = "VDVI";
omap3_pmic_init("twl4030", &beagle_twldata);
/* Bus 3 is attached to the DVI port where devices like the pico DLP
* projector don't work reliably with 400kHz */
omap_register_i2c_bus(3, 100, beagle_i2c_eeprom, ARRAY_SIZE(beagle_i2c_eeprom));
return 0;
}
static struct gpio_led gpio_leds[] = {
{
.name = "beagleboard::usr0",
.default_trigger = "heartbeat",
.gpio = 150,
},
{
.name = "beagleboard::usr1",
.default_trigger = "mmc0",
.gpio = 149,
},
};
static struct gpio_led_platform_data gpio_led_info = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device leds_gpio = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_led_info,
},
};
static struct gpio_keys_button gpio_buttons[] = {
{
.code = BTN_EXTRA,
/* Dynamically assigned depending on board */
.gpio = -EINVAL,
.desc = "user",
.wakeup = 1,
},
};
static struct gpio_keys_platform_data gpio_key_info = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device keys_gpio = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &gpio_key_info,
},
};
static struct platform_device madc_hwmon = {
.name = "twl4030_madc_hwmon",
.id = -1,
};
static struct platform_device *omap3_beagle_devices[] __initdata = {
&leds_gpio,
&keys_gpio,
&madc_hwmon,
&leds_pwm,
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static int __init beagle_opp_init(void)
{
int r = 0;
if (!machine_is_omap3_beagle())
return 0;
/* Initialize the omap3 opp table if not already created. */
r = omap3_opp_init();
if (r < 0 && (r != -EEXIST)) {
pr_err("%s: opp default init failed\n", __func__);
return r;
}
/* Custom OPP enabled for all xM versions */
if (cpu_is_omap3630()) {
struct device *mpu_dev, *iva_dev;
mpu_dev = get_cpu_device(0);
iva_dev = omap_device_get_by_hwmod_name("iva");
if (!mpu_dev || IS_ERR(iva_dev)) {
pr_err("%s: Aiee.. no mpu/dsp devices? %p %p\n",
__func__, mpu_dev, iva_dev);
return -ENODEV;
}
/* Enable MPU 1GHz and lower opps */
r = dev_pm_opp_enable(mpu_dev, 800000000);
/* TODO: MPU 1GHz needs SR and ABB */
/* Enable IVA 800MHz and lower opps */
r |= dev_pm_opp_enable(iva_dev, 660000000);
/* TODO: DSP 800MHz needs SR and ABB */
if (r) {
pr_err("%s: failed to enable higher opp %d\n",
__func__, r);
/*
* Cleanup - disable the higher freqs - we dont care
* about the results
*/
dev_pm_opp_disable(mpu_dev, 800000000);
dev_pm_opp_disable(iva_dev, 660000000);
}
}
return 0;
}
omap_device_initcall(beagle_opp_init);
static void __init omap3_beagle_init(void)
{
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
omap3_beagle_init_rev();
if (gpio_is_valid(beagle_config.mmc1_gpio_wp))
omap_mux_init_gpio(beagle_config.mmc1_gpio_wp, OMAP_PIN_INPUT);
mmc[0].caps = beagle_config.mmc_caps;
omap_hsmmc_init(mmc);
omap3_beagle_i2c_init();
gpio_buttons[0].gpio = beagle_config.usr_button_gpio;
platform_add_devices(omap3_beagle_devices,
ARRAY_SIZE(omap3_beagle_devices));
if (gpio_is_valid(beagle_config.dvi_pd_gpio))
omap_mux_init_gpio(beagle_config.dvi_pd_gpio, OMAP_PIN_OUTPUT);
omap_display_init(&beagle_dss_data);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
usbhs_init(&usbhs_bdata);
board_nand_init(omap3beagle_nand_partitions,
ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS,
NAND_BUSWIDTH_16, NULL);
omap_twl4030_audio_init("omap3beagle", NULL);
/* Ensure msecure is mux'd to be able to set the RTC. */
omap_mux_init_signal("sys_drm_msecure", OMAP_PIN_OFF_OUTPUT_HIGH);
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
pwm_add_table(pwm_lookup, ARRAY_SIZE(pwm_lookup));
}
MACHINE_START(OMAP3_BEAGLE, "OMAP3 Beagle Board")
/* Maintainer: Syed Mohammed Khasim - http://beagleboard.org */
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap3_init_early,
.init_irq = omap3_init_irq,
.init_machine = omap3_beagle_init,
.init_late = omap3_init_late,
.init_time = omap3_secure_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
arch/arm/mach-omap2/board-overo.c deleted 100644 → 0
View file @ cbdf76ab
/*
* board-overo.c (Gumstix Overo)
*
* Initial code: Steve Sakoman <steve@sakoman.com>
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* version 2 as published by the Free Software Foundation.
*
* This program is distributed in the hope that it will be useful, but
* WITHOUT ANY WARRANTY; without even the implied warranty of
* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
* General Public License for more details.
*
* You should have received a copy of the GNU General Public License
* along with this program; if not, write to the Free Software
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA
* 02110-1301 USA
*
*/
#include <linux/clk.h>
#include <linux/delay.h>
#include <linux/err.h>
#include <linux/init.h>
#include <linux/io.h>
#include <linux/gpio.h>
#include <linux/kernel.h>
#include <linux/platform_device.h>
#include <linux/i2c/twl.h>
#include <linux/regulator/machine.h>
#include <linux/regulator/fixed.h>
#include <linux/spi/spi.h>
#include <linux/mtd/mtd.h>
#include <linux/mtd/nand.h>
#include <linux/mtd/partitions.h>
#include <linux/mmc/host.h>
#include <linux/usb/phy.h>
#include <linux/platform_data/mtd-nand-omap2.h>
#include <linux/platform_data/spi-omap2-mcspi.h>
#include <asm/mach-types.h>
#include <asm/mach/arch.h>
#include <asm/mach/flash.h>
#include <asm/mach/map.h>
#include <video/omapdss.h>
#include <video/omap-panel-data.h>
#include "common.h"
#include "mux.h"
#include "sdram-micron-mt46h32m32lf-6.h"
#include "gpmc.h"
#include "hsmmc.h"
#include "board-flash.h"
#include "common-board-devices.h"
#define NAND_CS 0
#define OVERO_GPIO_BT_XGATE 15
#define OVERO_GPIO_W2W_NRESET 16
#define OVERO_GPIO_PENDOWN 114
#define OVERO_GPIO_BT_NRESET 164
#define OVERO_GPIO_USBH_CPEN 168
#define OVERO_GPIO_USBH_NRESET 183
#define OVERO_SMSC911X_CS 5
#define OVERO_SMSC911X_GPIO 176
#define OVERO_SMSC911X_NRESET 64
#define OVERO_SMSC911X2_CS 4
#define OVERO_SMSC911X2_GPIO 65
/* whether to register LCD35 instead of LCD43 */
static bool overo_use_lcd35;
#if defined(CONFIG_TOUCHSCREEN_ADS7846) || \
defined(CONFIG_TOUCHSCREEN_ADS7846_MODULE)
/* fixed regulator for ads7846 */
static struct regulator_consumer_supply ads7846_supply[] = {
REGULATOR_SUPPLY("vcc", "spi1.0"),
};
static struct regulator_init_data vads7846_regulator = {
.constraints = {
.valid_ops_mask = REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(ads7846_supply),
.consumer_supplies = ads7846_supply,
};
static struct fixed_voltage_config vads7846 = {
.supply_name = "vads7846",
.microvolts = 3300000, /* 3.3V */
.gpio = -EINVAL,
.startup_delay = 0,
.init_data = &vads7846_regulator,
};
static struct platform_device vads7846_device = {
.name = "reg-fixed-voltage",
.id = 1,
.dev = {
.platform_data = &vads7846,
},
};
static void __init overo_ads7846_init(void)
{
omap_ads7846_init(1, OVERO_GPIO_PENDOWN, 0, NULL);
platform_device_register(&vads7846_device);
}
#else
static inline void __init overo_ads7846_init(void) { return; }
#endif
#if defined(CONFIG_SMSC911X) || defined(CONFIG_SMSC911X_MODULE)
#include <linux/smsc911x.h>
#include "gpmc-smsc911x.h"
static struct omap_smsc911x_platform_data smsc911x_cfg = {
.id = 0,
.cs = OVERO_SMSC911X_CS,
.gpio_irq = OVERO_SMSC911X_GPIO,
.gpio_reset = OVERO_SMSC911X_NRESET,
.flags = SMSC911X_USE_32BIT,
};
static struct omap_smsc911x_platform_data smsc911x2_cfg = {
.id = 1,
.cs = OVERO_SMSC911X2_CS,
.gpio_irq = OVERO_SMSC911X2_GPIO,
.gpio_reset = -EINVAL,
.flags = SMSC911X_USE_32BIT,
};
static void __init overo_init_smsc911x(void)
{
gpmc_smsc911x_init(&smsc911x_cfg);
gpmc_smsc911x_init(&smsc911x2_cfg);
}
#else
static inline void __init overo_init_smsc911x(void) { return; }
#endif
/* DSS */
#define OVERO_GPIO_LCD_EN 144
#define OVERO_GPIO_LCD_BL 145
static struct connector_atv_platform_data overo_tv_pdata = {
.name = "tv",
.source = "venc.0",
.connector_type = OMAP_DSS_VENC_TYPE_SVIDEO,
.invert_polarity = false,
};
static struct platform_device overo_tv_connector_device = {
.name = "connector-analog-tv",
.id = 0,
.dev.platform_data = &overo_tv_pdata,
};
static const struct display_timing overo_lcd43_videomode = {
.pixelclock = { 0, 9200000, 0 },
.hactive = { 0, 480, 0 },
.hfront_porch = { 0, 8, 0 },
.hback_porch = { 0, 4, 0 },
.hsync_len = { 0, 41, 0 },
.vactive = { 0, 272, 0 },
.vfront_porch = { 0, 4, 0 },
.vback_porch = { 0, 2, 0 },
.vsync_len = { 0, 10, 0 },
.flags = DISPLAY_FLAGS_HSYNC_LOW | DISPLAY_FLAGS_VSYNC_LOW |
DISPLAY_FLAGS_DE_HIGH | DISPLAY_FLAGS_PIXDATA_POSEDGE,
};
static struct panel_dpi_platform_data overo_lcd43_pdata = {
.name = "lcd43",
.source = "dpi.0",
.data_lines = 24,
.display_timing = &overo_lcd43_videomode,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
static struct platform_device overo_lcd43_device = {
.name = "panel-dpi",
.id = 0,
.dev.platform_data = &overo_lcd43_pdata,
};
static struct connector_dvi_platform_data overo_dvi_connector_pdata = {
.name = "dvi",
.source = "tfp410.0",
.i2c_bus_num = 3,
};
static struct platform_device overo_dvi_connector_device = {
.name = "connector-dvi",
.id = 0,
.dev.platform_data = &overo_dvi_connector_pdata,
};
static struct encoder_tfp410_platform_data overo_tfp410_pdata = {
.name = "tfp410.0",
.source = "dpi.0",
.data_lines = 24,
.power_down_gpio = -1,
};
static struct platform_device overo_tfp410_device = {
.name = "tfp410",
.id = 0,
.dev.platform_data = &overo_tfp410_pdata,
};
static struct omap_dss_board_info overo_dss_data = {
.default_display_name = "lcd43",
};
static void __init overo_display_init(void)
{
omap_display_init(&overo_dss_data);
if (!overo_use_lcd35)
platform_device_register(&overo_lcd43_device);
platform_device_register(&overo_tfp410_device);
platform_device_register(&overo_dvi_connector_device);
platform_device_register(&overo_tv_connector_device);
}
static struct mtd_partition overo_nand_partitions[] = {
{
.name = "xloader",
.offset = 0, /* Offset = 0x00000 */
.size = 4 * NAND_BLOCK_SIZE,
.mask_flags = MTD_WRITEABLE
},
{
.name = "uboot",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x80000 */
.size = 14 * NAND_BLOCK_SIZE,
},
{
.name = "uboot environment",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x240000 */
.size = 2 * NAND_BLOCK_SIZE,
},
{
.name = "linux",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x280000 */
.size = 32 * NAND_BLOCK_SIZE,
},
{
.name = "rootfs",
.offset = MTDPART_OFS_APPEND, /* Offset = 0x680000 */
.size = MTDPART_SIZ_FULL,
},
};
static struct omap2_hsmmc_info mmc[] = {
{
.mmc = 1,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
},
{
.mmc = 2,
.caps = MMC_CAP_4_BIT_DATA,
.gpio_cd = -EINVAL,
.gpio_wp = -EINVAL,
.transceiver = true,
.ocr_mask = 0x00100000, /* 3.3V */
},
{} /* Terminator */
};
static struct regulator_consumer_supply overo_vmmc1_supply[] = {
REGULATOR_SUPPLY("vmmc", "omap_hsmmc.0"),
};
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
#include <linux/leds.h>
static struct gpio_led gpio_leds[] = {
{
.name = "overo:red:gpio21",
.default_trigger = "heartbeat",
.gpio = 21,
.active_low = true,
},
{
.name = "overo:blue:gpio22",
.default_trigger = "none",
.gpio = 22,
.active_low = true,
},
{
.name = "overo:blue:COM",
.default_trigger = "mmc0",
.gpio = -EINVAL, /* gets replaced */
.active_low = true,
},
};
static struct gpio_led_platform_data gpio_leds_pdata = {
.leds = gpio_leds,
.num_leds = ARRAY_SIZE(gpio_leds),
};
static struct platform_device gpio_leds_device = {
.name = "leds-gpio",
.id = -1,
.dev = {
.platform_data = &gpio_leds_pdata,
},
};
static void __init overo_init_led(void)
{
platform_device_register(&gpio_leds_device);
}
#else
static inline void __init overo_init_led(void) { return; }
#endif
#if defined(CONFIG_KEYBOARD_GPIO) || defined(CONFIG_KEYBOARD_GPIO_MODULE)
#include <linux/input.h>
#include <linux/gpio_keys.h>
static struct gpio_keys_button gpio_buttons[] = {
{
.code = BTN_0,
.gpio = 23,
.desc = "button0",
.wakeup = 1,
},
{
.code = BTN_1,
.gpio = 14,
.desc = "button1",
.wakeup = 1,
},
};
static struct gpio_keys_platform_data gpio_keys_pdata = {
.buttons = gpio_buttons,
.nbuttons = ARRAY_SIZE(gpio_buttons),
};
static struct platform_device gpio_keys_device = {
.name = "gpio-keys",
.id = -1,
.dev = {
.platform_data = &gpio_keys_pdata,
},
};
static void __init overo_init_keys(void)
{
platform_device_register(&gpio_keys_device);
}
#else
static inline void __init overo_init_keys(void) { return; }
#endif
static int overo_twl_gpio_setup(struct device *dev,
unsigned gpio, unsigned ngpio)
{
#if defined(CONFIG_LEDS_GPIO) || defined(CONFIG_LEDS_GPIO_MODULE)
/* TWL4030_GPIO_MAX + 1 == ledB, PMU_STAT (out, active low LED) */
gpio_leds[2].gpio = gpio + TWL4030_GPIO_MAX + 1;
#endif
return 0;
}
static struct twl4030_gpio_platform_data overo_gpio_data = {
.use_leds = true,
.setup = overo_twl_gpio_setup,
};
static struct regulator_init_data overo_vmmc1 = {
.constraints = {
.min_uV = 1850000,
.max_uV = 3150000,
.valid_modes_mask = REGULATOR_MODE_NORMAL
| REGULATOR_MODE_STANDBY,
.valid_ops_mask = REGULATOR_CHANGE_VOLTAGE
| REGULATOR_CHANGE_MODE
| REGULATOR_CHANGE_STATUS,
},
.num_consumer_supplies = ARRAY_SIZE(overo_vmmc1_supply),
.consumer_supplies = overo_vmmc1_supply,
};
static struct twl4030_platform_data overo_twldata = {
.gpio = &overo_gpio_data,
.vmmc1 = &overo_vmmc1,
};
static int __init overo_i2c_init(void)
{
omap3_pmic_get_config(&overo_twldata,
TWL_COMMON_PDATA_USB | TWL_COMMON_PDATA_AUDIO,
TWL_COMMON_REGULATOR_VDAC | TWL_COMMON_REGULATOR_VPLL2);
overo_twldata.vpll2->constraints.name = "VDVI";
omap3_pmic_init("tps65950", &overo_twldata);
/* i2c2 pins are used for gpio */
omap_register_i2c_bus(3, 400, NULL, 0);
return 0;
}
static struct panel_lb035q02_platform_data overo_lcd35_pdata = {
.name = "lcd35",
.source = "dpi.0",
.data_lines = 24,
.enable_gpio = OVERO_GPIO_LCD_EN,
.backlight_gpio = OVERO_GPIO_LCD_BL,
};
/*
* NOTE: We need to add either the lgphilips panel, or the lcd43 panel. The
* selection is done based on the overo_use_lcd35 field. If new SPI
* devices are added here, extra work is needed to make only the lgphilips panel
* affected by the overo_use_lcd35 field.
*/
static struct spi_board_info overo_spi_board_info[] __initdata = {
{
.modalias = "panel_lgphilips_lb035q02",
.bus_num = 1,
.chip_select = 1,
.max_speed_hz = 500000,
.mode = SPI_MODE_3,
.platform_data = &overo_lcd35_pdata,
},
};
static int __init overo_spi_init(void)
{
overo_ads7846_init();
if (overo_use_lcd35) {
spi_register_board_info(overo_spi_board_info,
ARRAY_SIZE(overo_spi_board_info));
}
return 0;
}
static struct usbhs_phy_data phy_data[] __initdata = {
{
.port = 2,
.reset_gpio = OVERO_GPIO_USBH_NRESET,
.vcc_gpio = -EINVAL,
},
};
static struct usbhs_omap_platform_data usbhs_bdata __initdata = {
.port_mode[1] = OMAP_EHCI_PORT_MODE_PHY,
};
#ifdef CONFIG_OMAP_MUX
static struct omap_board_mux board_mux[] __initdata = {
{ .reg_offset = OMAP_MUX_TERMINATOR },
};
#endif
static struct gpio overo_bt_gpios[] __initdata = {
{ OVERO_GPIO_BT_XGATE, GPIOF_OUT_INIT_LOW, "lcd enable" },
{ OVERO_GPIO_BT_NRESET, GPIOF_OUT_INIT_HIGH, "lcd bl enable" },
};
static struct regulator_consumer_supply dummy_supplies[] = {
REGULATOR_SUPPLY("vddvario", "smsc911x.0"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.0"),
REGULATOR_SUPPLY("vddvario", "smsc911x.1"),
REGULATOR_SUPPLY("vdd33a", "smsc911x.1"),
};
static void __init overo_init(void)
{
int ret;
if (strstr(boot_command_line, "omapdss.def_disp=lcd35"))
overo_use_lcd35 = true;
regulator_register_fixed(0, dummy_supplies, ARRAY_SIZE(dummy_supplies));
omap3_mux_init(board_mux, OMAP_PACKAGE_CBB);
overo_i2c_init();
omap_hsmmc_init(mmc);
omap_serial_init();
omap_sdrc_init(mt46h32m32lf6_sdrc_params,
mt46h32m32lf6_sdrc_params);
board_nand_init(overo_nand_partitions,
ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL);
usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb");
usb_musb_init(NULL);
usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data));
usbhs_init(&usbhs_bdata);
overo_spi_init();
overo_init_smsc911x();
overo_init_led();
overo_init_keys();
omap_twl4030_audio_init("overo", NULL);
overo_display_init();
/* Ensure SDRC pins are mux'd for self-refresh */
omap_mux_init_signal("sdrc_cke0", OMAP_PIN_OUTPUT);
omap_mux_init_signal("sdrc_cke1", OMAP_PIN_OUTPUT);
ret = gpio_request_one(OVERO_GPIO_W2W_NRESET, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_W2W_NRESET");
if (ret == 0) {
gpio_export(OVERO_GPIO_W2W_NRESET, 0);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 0);
udelay(10);
gpio_set_value(OVERO_GPIO_W2W_NRESET, 1);
} else {
pr_err("could not obtain gpio for OVERO_GPIO_W2W_NRESET\n");
}
ret = gpio_request_array(overo_bt_gpios, ARRAY_SIZE(overo_bt_gpios));
if (ret) {
pr_err("%s: could not obtain BT gpios\n", __func__);
} else {
gpio_export(OVERO_GPIO_BT_XGATE, 0);
gpio_export(OVERO_GPIO_BT_NRESET, 0);
gpio_set_value(OVERO_GPIO_BT_NRESET, 0);
mdelay(6);
gpio_set_value(OVERO_GPIO_BT_NRESET, 1);
}
ret = gpio_request_one(OVERO_GPIO_USBH_CPEN, GPIOF_OUT_INIT_HIGH,
"OVERO_GPIO_USBH_CPEN");
if (ret == 0)
gpio_export(OVERO_GPIO_USBH_CPEN, 0);
else
pr_err("could not obtain gpio for OVERO_GPIO_USBH_CPEN\n");
}
MACHINE_START(OVERO, "Gumstix Overo")
.atag_offset = 0x100,
.reserve = omap_reserve,
.map_io = omap3_map_io,
.init_early = omap35xx_init_early,
.init_irq = omap3_init_irq,
.init_machine = overo_init,
.init_late = omap35xx_init_late,
.init_time = omap3_sync32k_timer_init,
.restart = omap3xxx_restart,
MACHINE_END
arch/arm/mach-omap2/devices.c
View file @ 2ed25580
......@@ -63,7 +63,7 @@ static int __init omap3_l3_init(void)
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap3_l3_init);
......@@ -333,6 +333,6 @@ static int __init omap_gpmc_init(void)
pdev = omap_device_build("omap-gpmc", -1, oh, NULL, 0);
WARN(IS_ERR(pdev), "could not build omap_device for %s\n", oh_name);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
omap_postcore_initcall(omap_gpmc_init);
arch/arm/mach-omap2/fb.c
View file @ 2ed25580
......@@ -84,7 +84,7 @@ int __init omap_init_vrfb(void)
pdev = platform_device_register_resndata(NULL, "omapvrfb", -1,
res, num_res, NULL, 0);
return PTR_RET(pdev);
return PTR_ERR_OR_ZERO(pdev);
}
#else
int __init omap_init_vrfb(void) { return 0; }
......
arch/arm/mach-omap2/omap-wakeupgen.c
View file @ 2ed25580
......@@ -444,7 +444,7 @@ static int wakeupgen_domain_alloc(struct irq_domain *domain,
return irq_domain_alloc_irqs_parent(domain, virq, nr_irqs, &parent_args);
}
static struct irq_domain_ops wakeupgen_domain_ops = {
static const struct irq_domain_ops wakeupgen_domain_ops = {
.xlate = wakeupgen_domain_xlate,
.alloc = wakeupgen_domain_alloc,
.free = irq_domain_free_irqs_common,
......
arch/arm/mach-omap2/pmu.c
View file @ 2ed25580
......@@ -55,7 +55,7 @@ static int __init omap2_init_pmu(unsigned oh_num, char *oh_names[])
WARN(IS_ERR(omap_pmu_dev), "Can't build omap_device for %s.\n",
dev_name);
return PTR_RET(omap_pmu_dev);
return PTR_ERR_OR_ZERO(omap_pmu_dev);
}
static int __init omap_init_pmu(void)
......
arch/arm/mach-omap2/serial.c
View file @ 2ed25580
......@@ -203,7 +203,7 @@ static int __init omap_serial_early_init(void)
if (cmdline_find_option(uart_name)) {
console_uart_id = uart->num;
if (console_loglevel >= 10) {
if (console_loglevel >= CONSOLE_LOGLEVEL_DEBUG) {
uart_debug = true;
pr_info("%s used as console in debug mode: uart%d clocks will not be gated",
uart_name, uart->num);
......
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7