dmaengine: ti: cleanup comments

Remove the second 'the'

Replacements
completetion to completion
seens to seen
pendling to pending
atleast to at least
tranfer to transfer
multibple to a multiple
transfering to transferring
Signed-off-by: Tom Rix <trix@redhat.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@gmail.com>
Reviewed-by: Randy Dunlap <rdunlap@infradead.org>
Link: https://lore.kernel.org/r/20220217182546.3266909-1-trix@redhat.comSigned-off-by: Vinod Koul <vkoul@kernel.org>

drivers/dma/ti/cppi41.c

@@ -315,7 +315,7 @@ static irqreturn_t cppi41_irq(int irq, void *data)
 		val = cppi_readl(cdd->qmgr_mem + QMGR_PEND(i));
 		if (i == QMGR_PENDING_SLOT_Q(first_completion_queue) && val) {
 			u32 mask;
-			/* set corresponding bit for completetion Q 93 */
+			/* set corresponding bit for completion Q 93 */
 			mask = 1 << QMGR_PENDING_BIT_Q(first_completion_queue);
 			/* not set all bits for queues less than Q 93 */
 			mask--;
@@ -703,7 +703,7 @@ static int cppi41_tear_down_chan(struct cppi41_channel *c)
 	 * transfer descriptor followed by TD descriptor. Waiting seems not to
 	 * cause any difference.
 	 * RX seems to be thrown out right away. However once the TearDown
-	 * descriptor gets through we are done. If we have seens the transfer
+	 * descriptor gets through we are done. If we have seen the transfer
 	 * descriptor before the TD we fetch it from enqueue, it has to be
 	 * there waiting for us.
 	 */
@@ -747,7 +747,7 @@ static int cppi41_stop_chan(struct dma_chan *chan)
 		struct cppi41_channel *cc, *_ct;
 
 		/*
-		 * channels might still be in the pendling list if
+		 * channels might still be in the pending list if
 		 * cppi41_dma_issue_pending() is called after
 		 * cppi41_runtime_suspend() is called
 		 */

drivers/dma/ti/edma.c

@@ -118,10 +118,10 @@
 
 /*
  * Max of 20 segments per channel to conserve PaRAM slots
- * Also note that MAX_NR_SG should be atleast the no.of periods
+ * Also note that MAX_NR_SG should be at least the no.of periods
  * that are required for ASoC, otherwise DMA prep calls will
  * fail. Today davinci-pcm is the only user of this driver and
- * requires atleast 17 slots, so we setup the default to 20.
+ * requires at least 17 slots, so we setup the default to 20.
  */
 #define MAX_NR_SG		20
 #define EDMA_MAX_SLOTS		MAX_NR_SG
@@ -976,7 +976,7 @@ static int edma_config_pset(struct dma_chan *chan, struct edma_pset *epset,
 		 * and quotient respectively of the division of:
 		 * (dma_length / acnt) by (SZ_64K -1). This is so
 		 * that in case bcnt over flows, we have ccnt to use.
-		 * Note: In A-sync tranfer only, bcntrld is used, but it
+		 * Note: In A-sync transfer only, bcntrld is used, but it
 		 * only applies for sg_dma_len(sg) >= SZ_64K.
 		 * In this case, the best way adopted is- bccnt for the
 		 * first frame will be the remainder below. Then for
@@ -1203,7 +1203,7 @@ static struct dma_async_tx_descriptor *edma_prep_dma_memcpy(
 		 * slot2: the remaining amount of data after slot1.
 		 *	  ACNT = full_length - length1, length2 = ACNT
 		 *
-		 * When the full_length is multibple of 32767 one slot can be
+		 * When the full_length is a multiple of 32767 one slot can be
 		 * used to complete the transfer.
 		 */
 		width = array_size;
@@ -1814,7 +1814,7 @@ static void edma_issue_pending(struct dma_chan *chan)
  * This limit exists to avoid a possible infinite loop when waiting for proof
  * that a particular transfer is completed. This limit can be hit if there
  * are large bursts to/from slow devices or the CPU is never able to catch
- * the DMA hardware idle. On an AM335x transfering 48 bytes from the UART
+ * the DMA hardware idle. On an AM335x transferring 48 bytes from the UART
  * RX-FIFO, as many as 55 loops have been seen.
  */
 #define EDMA_MAX_TR_WAIT_LOOPS 1000

drivers/dma/ti/omap-dma.c

@@ -1442,7 +1442,7 @@ static int omap_dma_pause(struct dma_chan *chan)
 	 * A source-synchronised channel is one where the fetching of data is
 	 * under control of the device. In other words, a device-to-memory
 	 * transfer. So, a destination-synchronised channel (which would be a
-	 * memory-to-device transfer) undergoes an abort if the the CCR_ENABLE
+	 * memory-to-device transfer) undergoes an abort if the CCR_ENABLE
 	 * bit is cleared.
 	 * From 16.1.4.20.4.6.2 Abort: "If an abort trigger occurs, the channel
 	 * aborts immediately after completion of current read/write