arm64: zynqmp: Add output-enable pins to SOMs

Now that the zynqmp pinctrl driver supports the tri-state registers, make
sure that the pins requiring output-enable are configured appropriately for
SOMs.

Without it, all tristate setting for MIOs, which are not related to SOM
itself, are using default configuration which is not correct setting.
It means SDs, USBs, ethernet, etc. are not working properly.

In past it was fixed through calling tristate configuration via bootcmd:
usb_init=mw 0xFF180208 2020
kv260_gem3=mw 0xFF18020C 0xFC0 && gpio toggle gpio@ff0a000038 && \
  gpio toggle gpio@ff0a000038
Signed-off-by: Neal Frager <neal.frager@amd.com>
Link: https://lore.kernel.org/r/9270938b48c8939ac5dca4ac2c59f1c4a8c564d8.1704728353.git.michal.simek@amd.comSigned-off-by: Michal Simek <michal.simek@amd.com>

arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revA.dtso

@@ -185,6 +185,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -236,6 +237,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -243,6 +245,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -251,6 +254,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -281,6 +285,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};

arch/arm64/boot/dts/xilinx/zynqmp-sck-kv-g-revB.dtso

@@ -168,6 +168,7 @@ conf-rx {
 		conf-tx {
 			pins = "MIO36";
 			bias-disable;
+			output-enable;
 		};
 
 		mux {
@@ -219,6 +220,7 @@ conf-rx {
 		conf-bootstrap {
 			pins = "MIO71", "MIO73", "MIO75";
 			bias-disable;
+			output-enable;
 			low-power-disable;
 		};
 
@@ -226,6 +228,7 @@ conf-tx {
 			pins = "MIO64", "MIO65", "MIO66",
 				"MIO67", "MIO68", "MIO69";
 			bias-disable;
+			output-enable;
 			low-power-enable;
 		};
 
@@ -234,6 +237,7 @@ conf-mdio {
 			slew-rate = <SLEW_RATE_SLOW>;
 			power-source = <IO_STANDARD_LVCMOS18>;
 			bias-disable;
+			output-enable;
 		};
 
 		mux-mdio {
@@ -264,6 +268,7 @@ conf-tx {
 			pins = "MIO54", "MIO56", "MIO57", "MIO58", "MIO59",
 			"MIO60", "MIO61", "MIO62", "MIO63";
 			bias-disable;
+			output-enable;
 			drive-strength = <4>;
 			slew-rate = <SLEW_RATE_SLOW>;
 		};