ARM: dts: Add exynos5420 peach-pit board support

Adds the google peach-pit board dts file which uses
exynos5420 SoC.
Signed-off-by: Arun Kumar K <arun.kk@samsung.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>

arch/arm/boot/dts/Makefile

@@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
 	exynos5250-smdk5250.dtb \
 	exynos5250-snow.dtb \
 	exynos5420-arndale-octa.dtb \
+	exynos5420-peach-pit.dtb \
 	exynos5420-smdk5420.dtb \
 	exynos5440-sd5v1.dtb \
 	exynos5440-ssdk5440.dtb

arch/arm/boot/dts/exynos5420-peach-pit.dts

+/*
+ * Google Peach Pit Rev 6+ board device tree source
+ *
+ * Copyright (c) 2014 Google, Inc
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "exynos5420.dtsi"
+
+/ {
+	model = "Google Peach Pit Rev 6+";
+
+	compatible = "google,pit-rev16",
+		"google,pit-rev15", "google,pit-rev14",
+		"google,pit-rev13", "google,pit-rev12",
+		"google,pit-rev11", "google,pit-rev10",
+		"google,pit-rev9", "google,pit-rev8",
+		"google,pit-rev7", "google,pit-rev6",
+		"google,pit", "google,peach","samsung,exynos5420",
+		"samsung,exynos5";
+
+	memory {
+		reg = <0x20000000 0x80000000>;
+	};
+
+	fixed-rate-clocks {
+		oscclk {
+			compatible = "samsung,exynos5420-oscclk";
+			clock-frequency = <24000000>;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&power_key_irq>;
+
+		power {
+			label = "Power";
+			gpios = <&gpx1 2 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_POWER>;
+			gpio-key,wakeup;
+		};
+	};
+
+	backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pwm 0 1000000 0>;
+		brightness-levels = <0 100 500 1000 1500 2000 2500 2800>;
+		default-brightness-level = <7>;
+		pinctrl-0 = <&pwm0_out>;
+		pinctrl-names = "default";
+	};
+};
+
+&pinctrl_0 {
+	tpm_irq: tpm-irq {
+		samsung,pins = "gpx1-0";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+
+	power_key_irq: power-key-irq {
+		samsung,pins = "gpx1-2";
+		samsung,pin-function = <0>;
+		samsung,pin-pud = <0>;
+		samsung,pin-drv = <0>;
+	};
+};
+
+&rtc {
+	status = "okay";
+};
+
+&uart_3 {
+	status = "okay";
+};
+
+&mmc_0 {
+	status = "okay";
+	num-slots = <1>;
+	broken-cd;
+	caps2-mmc-hs200-1_8v;
+	supports-highspeed;
+	non-removable;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <0 4>;
+	samsung,dw-mshc-ddr-timing = <0 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd0_clk &sd0_cmd &sd0_bus4 &sd0_bus8>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <8>;
+	};
+};
+
+&mmc_2 {
+	status = "okay";
+	num-slots = <1>;
+	supports-highspeed;
+	card-detect-delay = <200>;
+	clock-frequency = <400000000>;
+	samsung,dw-mshc-ciu-div = <3>;
+	samsung,dw-mshc-sdr-timing = <2 3>;
+	samsung,dw-mshc-ddr-timing = <1 2>;
+	pinctrl-names = "default";
+	pinctrl-0 = <&sd2_clk &sd2_cmd &sd2_cd &sd2_bus4>;
+
+	slot@0 {
+		reg = <0>;
+		bus-width = <4>;
+	};
+};
+
+&hsi2c_9 {
+	status = "okay";
+	clock-frequency = <400000>;
+
+	tpm@20 {
+		compatible = "infineon,slb9645tt";
+		reg = <0x20>;
+
+		/* Unused irq; but still need to configure the pins */
+		pinctrl-names = "default";
+		pinctrl-0 = <&tpm_irq>;
+	};
+};
+
+/*
+ * Use longest HW watchdog in SoC (32 seconds) since the hardware
+ * watchdog provides no debugging information (compared to soft/hard
+ * lockup detectors) and so should be last resort.
+ */
+&watchdog {
+	timeout-sec = <32>;
+};