Merge git://github.com/Jkirsher/net-next

drivers/net/ethernet/intel/e1000/e1000_main.c

@@ -1814,8 +1814,8 @@ static void e1000_setup_rctl(struct e1000_adapter *adapter)
 
 	rctl &= ~(3 << E1000_RCTL_MO_SHIFT);
 
-	rctl |= E1000_RCTL_EN | E1000_RCTL_BAM |
-		E1000_RCTL_LBM_NO | E1000_RCTL_RDMTS_HALF |
+	rctl |= E1000_RCTL_BAM | E1000_RCTL_LBM_NO |
+		E1000_RCTL_RDMTS_HALF |
 		(hw->mc_filter_type << E1000_RCTL_MO_SHIFT);
 
 	if (hw->tbi_compatibility_on == 1)
@@ -1917,7 +1917,7 @@ static void e1000_configure_rx(struct e1000_adapter *adapter)
 	}
 
 	/* Enable Receives */
-	ew32(RCTL, rctl);
+	ew32(RCTL, rctl | E1000_RCTL_EN);
 }
 
 /**

drivers/net/ethernet/intel/ixgbe/ixgbe.h

@@ -301,26 +301,29 @@ struct ixgbe_ring_container {
  */
 struct ixgbe_q_vector {
 	struct ixgbe_adapter *adapter;
-	unsigned int v_idx; /* index of q_vector within array, also used for
-	                     * finding the bit in EICR and friends that
-	                     * represents the vector for this ring */
 #ifdef CONFIG_IXGBE_DCA
 	int cpu;	    /* CPU for DCA */
 #endif
-	struct napi_struct napi;
+	u16 v_idx;		/* index of q_vector within array, also used for
+				 * finding the bit in EICR and friends that
+				 * represents the vector for this ring */
+	u16 itr;		/* Interrupt throttle rate written to EITR */
 	struct ixgbe_ring_container rx, tx;
-	u32 eitr;
+
+	struct napi_struct napi;
 	cpumask_var_t affinity_mask;
 	char name[IFNAMSIZ + 9];
 };
 
-/* Helper macros to switch between ints/sec and what the register uses.
- * And yes, it's the same math going both ways.  The lowest value
- * supported by all of the ixgbe hardware is 8.
+/*
+ * microsecond values for various ITR rates shifted by 2 to fit itr register
+ * with the first 3 bits reserved 0
  */
-#define EITR_INTS_PER_SEC_TO_REG(_eitr) \
-	((_eitr) ? (1000000000 / ((_eitr) * 256)) : 8)
-#define EITR_REG_TO_INTS_PER_SEC EITR_INTS_PER_SEC_TO_REG
+#define IXGBE_MIN_RSC_ITR	24
+#define IXGBE_100K_ITR		40
+#define IXGBE_20K_ITR		200
+#define IXGBE_10K_ITR		400
+#define IXGBE_8K_ITR		500
 
 static inline u16 ixgbe_desc_unused(struct ixgbe_ring *ring)
 {

drivers/net/ethernet/intel/ixgbe/ixgbe_82598.c

@@ -358,7 +358,6 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 	u32 fctrl_reg;
 	u32 rmcs_reg;
 	u32 reg;
-	u32 rx_pba_size;
 	u32 link_speed = 0;
 	bool link_up;
 
@@ -461,16 +460,13 @@ static s32 ixgbe_fc_enable_82598(struct ixgbe_hw *hw, s32 packetbuf_num)
 
 	/* Set up and enable Rx high/low water mark thresholds, enable XON. */
 	if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
-		rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num));
-		rx_pba_size >>= IXGBE_RXPBSIZE_SHIFT;
-
-		reg = (rx_pba_size - hw->fc.low_water) << 6;
+		reg = hw->fc.low_water << 6;
 		if (hw->fc.send_xon)
 			reg |= IXGBE_FCRTL_XONE;
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTL(packetbuf_num), reg);
 
-		reg = (rx_pba_size - hw->fc.high_water) << 6;
+		reg = hw->fc.high_water[packetbuf_num] << 6;
 		reg |= IXGBE_FCRTH_FCEN;
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTH(packetbuf_num), reg);

drivers/net/ethernet/intel/ixgbe/ixgbe_common.c

@@ -1932,7 +1932,6 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num)
 	s32 ret_val = 0;
 	u32 mflcn_reg, fccfg_reg;
 	u32 reg;
-	u32 rx_pba_size;
 	u32 fcrtl, fcrth;
 
 #ifdef CONFIG_DCB
@@ -2012,11 +2011,8 @@ s32 ixgbe_fc_enable_generic(struct ixgbe_hw *hw, s32 packetbuf_num)
 	IXGBE_WRITE_REG(hw, IXGBE_MFLCN, mflcn_reg);
 	IXGBE_WRITE_REG(hw, IXGBE_FCCFG, fccfg_reg);
 
-	rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(packetbuf_num));
-	rx_pba_size >>= IXGBE_RXPBSIZE_SHIFT;
-
-	fcrth = (rx_pba_size - hw->fc.high_water) << 10;
-	fcrtl = (rx_pba_size - hw->fc.low_water) << 10;
+	fcrth = hw->fc.high_water[packetbuf_num] << 10;
+	fcrtl = hw->fc.low_water << 10;
 
 	if (hw->fc.current_mode & ixgbe_fc_tx_pause) {
 		fcrth |= IXGBE_FCRTH_FCEN;
@@ -2293,7 +2289,9 @@ static s32 ixgbe_setup_fc(struct ixgbe_hw *hw, s32 packetbuf_num)
 	 * Validate the water mark configuration.  Zero water marks are invalid
 	 * because it causes the controller to just blast out fc packets.
 	 */
-	if (!hw->fc.low_water || !hw->fc.high_water || !hw->fc.pause_time) {
+	if (!hw->fc.low_water ||
+	    !hw->fc.high_water[packetbuf_num] ||
+	    !hw->fc.pause_time) {
 		hw_dbg(hw, "Invalid water mark configuration\n");
 		ret_val = IXGBE_ERR_INVALID_LINK_SETTINGS;
 		goto out;

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb.h

@@ -36,7 +36,6 @@
 
 #define IXGBE_MAX_PACKET_BUFFERS 8
 #define MAX_USER_PRIORITY        8
-#define MAX_TRAFFIC_CLASS        8
 #define MAX_BW_GROUP             8
 #define BW_PERCENT               100
 

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82598.c

@@ -191,7 +191,7 @@ s32 ixgbe_dcb_config_tx_data_arbiter_82598(struct ixgbe_hw *hw,
  */
 s32 ixgbe_dcb_config_pfc_82598(struct ixgbe_hw *hw, u8 pfc_en)
 {
-	u32 reg, rx_pba_size;
+	u32 reg;
 	u8  i;
 
 	if (pfc_en) {
@@ -222,9 +222,8 @@ s32 ixgbe_dcb_config_pfc_82598(struct ixgbe_hw *hw, u8 pfc_en)
 	 */
 	for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
 		int enabled = pfc_en & (1 << i);
-		rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i));
-		rx_pba_size >>= IXGBE_RXPBSIZE_SHIFT;
-		reg = (rx_pba_size - hw->fc.low_water) << 10;
+
+		reg = hw->fc.low_water << 10;
 
 		if (enabled == pfc_enabled_tx ||
 		    enabled == pfc_enabled_full)
@@ -232,7 +231,7 @@ s32 ixgbe_dcb_config_pfc_82598(struct ixgbe_hw *hw, u8 pfc_en)
 
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTL(i), reg);
 
-		reg = (rx_pba_size - hw->fc.high_water) << 10;
+		reg = hw->fc.high_water[i] << 10;
 		if (enabled == pfc_enabled_tx ||
 		    enabled == pfc_enabled_full)
 			reg |= IXGBE_FCRTH_FCEN;

drivers/net/ethernet/intel/ixgbe/ixgbe_dcb_82599.c

@@ -210,21 +210,19 @@ s32 ixgbe_dcb_config_tx_data_arbiter_82599(struct ixgbe_hw *hw,
  */
 s32 ixgbe_dcb_config_pfc_82599(struct ixgbe_hw *hw, u8 pfc_en)
 {
-	u32 i, reg, rx_pba_size;
+	u32 i, reg;
 
 	/* Configure PFC Tx thresholds per TC */
 	for (i = 0; i < MAX_TRAFFIC_CLASS; i++) {
 		int enabled = pfc_en & (1 << i);
-		rx_pba_size = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(i));
-		rx_pba_size >>= IXGBE_RXPBSIZE_SHIFT;
 
-		reg = (rx_pba_size - hw->fc.low_water) << 10;
+		reg = hw->fc.low_water << 10;
 
 		if (enabled)
 			reg |= IXGBE_FCRTL_XONE;
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTL_82599(i), reg);
 
-		reg = (rx_pba_size - hw->fc.high_water) << 10;
+		reg = hw->fc.high_water[i] << 10;
 		if (enabled)
 			reg |= IXGBE_FCRTH_FCEN;
 		IXGBE_WRITE_REG(hw, IXGBE_FCRTH_82599(i), reg);

drivers/net/ethernet/intel/ixgbe/ixgbe_ethtool.c

@@ -2026,39 +2026,20 @@ static int ixgbe_get_coalesce(struct net_device *netdev,
 	ec->tx_max_coalesced_frames_irq = adapter->tx_work_limit;
 
 	/* only valid if in constant ITR mode */
-	switch (adapter->rx_itr_setting) {
-	case 0:
-		/* throttling disabled */
-		ec->rx_coalesce_usecs = 0;
-		break;
-	case 1:
-		/* dynamic ITR mode */
-		ec->rx_coalesce_usecs = 1;
-		break;
-	default:
-		/* fixed interrupt rate mode */
-		ec->rx_coalesce_usecs = 1000000/adapter->rx_eitr_param;
-		break;
-	}
+	if (adapter->rx_itr_setting <= 1)
+		ec->rx_coalesce_usecs = adapter->rx_itr_setting;
+	else
+		ec->rx_coalesce_usecs = adapter->rx_itr_setting >> 2;
 
 	/* if in mixed tx/rx queues per vector mode, report only rx settings */
 	if (adapter->q_vector[0]->tx.count && adapter->q_vector[0]->rx.count)
 		return 0;
 
 	/* only valid if in constant ITR mode */
-	switch (adapter->tx_itr_setting) {
-	case 0:
-		/* throttling disabled */
-		ec->tx_coalesce_usecs = 0;
-		break;
-	case 1:
-		/* dynamic ITR mode */
-		ec->tx_coalesce_usecs = 1;
-		break;
-	default:
-		ec->tx_coalesce_usecs = 1000000/adapter->tx_eitr_param;
-		break;
-	}
+	if (adapter->tx_itr_setting <= 1)
+		ec->tx_coalesce_usecs = adapter->tx_itr_setting;
+	else
+		ec->tx_coalesce_usecs = adapter->tx_itr_setting >> 2;
 
 	return 0;
 }
@@ -2077,10 +2058,9 @@ static bool ixgbe_update_rsc(struct ixgbe_adapter *adapter,
 
 	/* if interrupt rate is too high then disable RSC */
 	if (ec->rx_coalesce_usecs != 1 &&
-	    ec->rx_coalesce_usecs <= 1000000/IXGBE_MAX_RSC_INT_RATE) {
+	    ec->rx_coalesce_usecs <= (IXGBE_MIN_RSC_ITR >> 2)) {
 		if (adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED) {
-			e_info(probe, "rx-usecs set too low, "
-				      "disabling RSC\n");
+			e_info(probe, "rx-usecs set too low, disabling RSC\n");
 			adapter->flags2 &= ~IXGBE_FLAG2_RSC_ENABLED;
 			return true;
 		}
@@ -2088,8 +2068,7 @@ static bool ixgbe_update_rsc(struct ixgbe_adapter *adapter,
 		/* check the feature flag value and enable RSC if necessary */
 		if ((netdev->features & NETIF_F_LRO) &&
 		    !(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED)) {
-			e_info(probe, "rx-usecs set to %d, "
-				      "re-enabling RSC\n",
+			e_info(probe, "rx-usecs set to %d, re-enabling RSC\n",
 			       ec->rx_coalesce_usecs);
 			adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED;
 			return true;
@@ -2104,6 +2083,8 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 	struct ixgbe_adapter *adapter = netdev_priv(netdev);
 	struct ixgbe_q_vector *q_vector;
 	int i;
+	int num_vectors;
+	u16 tx_itr_param, rx_itr_param;
 	bool need_reset = false;
 
 	/* don't accept tx specific changes if we've got mixed RxTx vectors */
@@ -2114,87 +2095,47 @@ static int ixgbe_set_coalesce(struct net_device *netdev,
 	if (ec->tx_max_coalesced_frames_irq)
 		adapter->tx_work_limit = ec->tx_max_coalesced_frames_irq;
 
-	if (ec->rx_coalesce_usecs > 1) {
-		/* check the limits */
-		if ((1000000/ec->rx_coalesce_usecs > IXGBE_MAX_INT_RATE) ||
-		    (1000000/ec->rx_coalesce_usecs < IXGBE_MIN_INT_RATE))
+	if ((ec->rx_coalesce_usecs > (IXGBE_MAX_EITR >> 2)) ||
+	    (ec->tx_coalesce_usecs > (IXGBE_MAX_EITR >> 2)))
 		return -EINVAL;
 
 	/* check the old value and enable RSC if necessary */
 	need_reset = ixgbe_update_rsc(adapter, ec);
 
-		/* store the value in ints/second */
-		adapter->rx_eitr_param = 1000000/ec->rx_coalesce_usecs;
-
-		/* static value of interrupt rate */
-		adapter->rx_itr_setting = adapter->rx_eitr_param;
-		/* clear the lower bit as its used for dynamic state */
-		adapter->rx_itr_setting &= ~1;
-	} else if (ec->rx_coalesce_usecs == 1) {
-		/* check the old value and enable RSC if necessary */
-		need_reset = ixgbe_update_rsc(adapter, ec);
-
-		/* 1 means dynamic mode */
-		adapter->rx_eitr_param = 20000;
-		adapter->rx_itr_setting = 1;
-	} else {
-		/* check the old value and enable RSC if necessary */
-		need_reset = ixgbe_update_rsc(adapter, ec);
-		/*
-		 * any other value means disable eitr, which is best
-		 * served by setting the interrupt rate very high
-		 */
-		adapter->rx_eitr_param = IXGBE_MAX_INT_RATE;
-		adapter->rx_itr_setting = 0;
-	}
+	if (ec->rx_coalesce_usecs > 1)
+		adapter->rx_itr_setting = ec->rx_coalesce_usecs << 2;
+	else
+		adapter->rx_itr_setting = ec->rx_coalesce_usecs;
 
-	if (ec->tx_coalesce_usecs > 1) {
-		/*
-		 * don't have to worry about max_int as above because
-		 * tx vectors don't do hardware RSC (an rx function)
-		 */
-		/* check the limits */
-		if ((1000000/ec->tx_coalesce_usecs > IXGBE_MAX_INT_RATE) ||
-		    (1000000/ec->tx_coalesce_usecs < IXGBE_MIN_INT_RATE))
-			return -EINVAL;
+	if (adapter->rx_itr_setting == 1)
+		rx_itr_param = IXGBE_20K_ITR;
+	else
+		rx_itr_param = adapter->rx_itr_setting;
 
-		/* store the value in ints/second */
-		adapter->tx_eitr_param = 1000000/ec->tx_coalesce_usecs;
+	if (ec->tx_coalesce_usecs > 1)
+		adapter->tx_itr_setting = ec->tx_coalesce_usecs << 2;
+	else
+		adapter->tx_itr_setting = ec->tx_coalesce_usecs;
 
-		/* static value of interrupt rate */
-		adapter->tx_itr_setting = adapter->tx_eitr_param;
+	if (adapter->tx_itr_setting == 1)
+		tx_itr_param = IXGBE_10K_ITR;
+	else
+		tx_itr_param = adapter->tx_itr_setting;
 
-		/* clear the lower bit as its used for dynamic state */
-		adapter->tx_itr_setting &= ~1;
-	} else if (ec->tx_coalesce_usecs == 1) {
-		/* 1 means dynamic mode */
-		adapter->tx_eitr_param = 10000;
-		adapter->tx_itr_setting = 1;
-	} else {
-		adapter->tx_eitr_param = IXGBE_MAX_INT_RATE;
-		adapter->tx_itr_setting = 0;
-	}
+	if (adapter->flags & IXGBE_FLAG_MSIX_ENABLED)
+		num_vectors = adapter->num_msix_vectors - NON_Q_VECTORS;
+	else
+		num_vectors = 1;
 
-	/* MSI/MSIx Interrupt Mode */
-	if (adapter->flags &
-	    (IXGBE_FLAG_MSIX_ENABLED | IXGBE_FLAG_MSI_ENABLED)) {
-		int num_vectors = adapter->num_msix_vectors - NON_Q_VECTORS;
 	for (i = 0; i < num_vectors; i++) {
 		q_vector = adapter->q_vector[i];
+		q_vector->tx.work_limit = adapter->tx_work_limit;
 		if (q_vector->tx.count && !q_vector->rx.count)
 			/* tx only */
-				q_vector->eitr = adapter->tx_eitr_param;
+			q_vector->itr = tx_itr_param;
 		else
 			/* rx only or mixed */
-				q_vector->eitr = adapter->rx_eitr_param;
-			q_vector->tx.work_limit = adapter->tx_work_limit;
-			ixgbe_write_eitr(q_vector);
-		}
-	/* Legacy Interrupt Mode */
-	} else {
-		q_vector = adapter->q_vector[0];
-		q_vector->eitr = adapter->rx_eitr_param;
-		q_vector->tx.work_limit = adapter->tx_work_limit;
+			q_vector->itr = rx_itr_param;
 		ixgbe_write_eitr(q_vector);
 	}
 

drivers/net/ethernet/intel/ixgbe/ixgbe_fcoe.c

@@ -661,9 +661,7 @@ void ixgbe_configure_fcoe(struct ixgbe_adapter *adapter)
 			IXGBE_ETQS_QUEUE_EN |
 			(fcoe_q << IXGBE_ETQS_RX_QUEUE_SHIFT));
 
-	IXGBE_WRITE_REG(hw, IXGBE_FCRXCTRL,
-			IXGBE_FCRXCTRL_FCOELLI |
-			IXGBE_FCRXCTRL_FCCRCBO |
+	IXGBE_WRITE_REG(hw, IXGBE_FCRXCTRL, IXGBE_FCRXCTRL_FCCRCBO |
 			(FC_FCOE_VER << IXGBE_FCRXCTRL_FCOEVER_SHIFT));
 	return;
 

drivers/net/ethernet/intel/ixgbe/ixgbe_main.c

@@ -1500,12 +1500,19 @@ static void ixgbe_configure_msix(struct ixgbe_adapter *adapter)
 		for (ring = q_vector->tx.ring; ring != NULL; ring = ring->next)
 			ixgbe_set_ivar(adapter, 1, ring->reg_idx, v_idx);
 
-		if (q_vector->tx.ring && !q_vector->rx.ring)
-			/* tx only */
-			q_vector->eitr = adapter->tx_eitr_param;
-		else if (q_vector->rx.ring)
-			/* rx or mixed */
-			q_vector->eitr = adapter->rx_eitr_param;
+		if (q_vector->tx.ring && !q_vector->rx.ring) {
+			/* tx only vector */
+			if (adapter->tx_itr_setting == 1)
+				q_vector->itr = IXGBE_10K_ITR;
+			else
+				q_vector->itr = adapter->tx_itr_setting;
+		} else {
+			/* rx or rx/tx vector */
+			if (adapter->rx_itr_setting == 1)
+				q_vector->itr = IXGBE_20K_ITR;
+			else
+				q_vector->itr = adapter->rx_itr_setting;
+		}
 
 		ixgbe_write_eitr(q_vector);
 	}
@@ -1519,7 +1526,6 @@ static void ixgbe_configure_msix(struct ixgbe_adapter *adapter)
 	case ixgbe_mac_X540:
 		ixgbe_set_ivar(adapter, -1, 1, v_idx);
 		break;
-
 	default:
 		break;
 	}
@@ -1527,12 +1533,10 @@ static void ixgbe_configure_msix(struct ixgbe_adapter *adapter)
 
 	/* set up to autoclear timer, and the vectors */
 	mask = IXGBE_EIMS_ENABLE_MASK;
-	if (adapter->num_vfs)
 	mask &= ~(IXGBE_EIMS_OTHER |
 		  IXGBE_EIMS_MAILBOX |
 		  IXGBE_EIMS_LSC);
-	else
-		mask &= ~(IXGBE_EIMS_OTHER | IXGBE_EIMS_LSC);
+
 	IXGBE_WRITE_REG(&adapter->hw, IXGBE_EIAC, mask);
 }
 
@@ -1577,7 +1581,7 @@ static void ixgbe_update_itr(struct ixgbe_q_vector *q_vector,
 	 *  100-1249MB/s bulk (8000 ints/s)
 	 */
 	/* what was last interrupt timeslice? */
-	timepassed_us = 1000000/q_vector->eitr;
+	timepassed_us = q_vector->itr >> 2;
 	bytes_perint = bytes / timepassed_us; /* bytes/usec */
 
 	switch (itr_setting) {
@@ -1618,7 +1622,7 @@ void ixgbe_write_eitr(struct ixgbe_q_vector *q_vector)
 	struct ixgbe_adapter *adapter = q_vector->adapter;
 	struct ixgbe_hw *hw = &adapter->hw;
 	int v_idx = q_vector->v_idx;
-	u32 itr_reg = EITR_INTS_PER_SEC_TO_REG(q_vector->eitr);
+	u32 itr_reg = q_vector->itr;
 
 	switch (adapter->hw.mac.type) {
 	case ixgbe_mac_82598EB:
@@ -1627,15 +1631,6 @@ void ixgbe_write_eitr(struct ixgbe_q_vector *q_vector)
 		break;
 	case ixgbe_mac_82599EB:
 	case ixgbe_mac_X540:
-		/*
-		 * 82599 and X540 can support a value of zero, so allow it for
-		 * max interrupt rate, but there is an errata where it can
-		 * not be zero with RSC
-		 */
-		if (itr_reg == 8 &&
-		    !(adapter->flags2 & IXGBE_FLAG2_RSC_ENABLED))
-			itr_reg = 0;
-
 		/*
 		 * set the WDIS bit to not clear the timer bits and cause an
 		 * immediate assertion of the interrupt
@@ -1650,7 +1645,7 @@ void ixgbe_write_eitr(struct ixgbe_q_vector *q_vector)
 
 static void ixgbe_set_itr(struct ixgbe_q_vector *q_vector)
 {
-	u32 new_itr = q_vector->eitr;
+	u32 new_itr = q_vector->itr;
 	u8 current_itr;
 
 	ixgbe_update_itr(q_vector, &q_vector->tx);
@@ -1661,24 +1656,25 @@ static void ixgbe_set_itr(struct ixgbe_q_vector *q_vector)
 	switch (current_itr) {
 	/* counts and packets in update_itr are dependent on these numbers */
 	case lowest_latency:
-		new_itr = 100000;
+		new_itr = IXGBE_100K_ITR;
 		break;
 	case low_latency:
-		new_itr = 20000; /* aka hwitr = ~200 */
+		new_itr = IXGBE_20K_ITR;
 		break;
 	case bulk_latency:
-		new_itr = 8000;
+		new_itr = IXGBE_8K_ITR;
 		break;
 	default:
 		break;
 	}
 
-	if (new_itr != q_vector->eitr) {
+	if (new_itr != q_vector->itr) {
 		/* do an exponential smoothing */
-		new_itr = ((q_vector->eitr * 9) + new_itr)/10;
+		new_itr = (10 * new_itr * q_vector->itr) /
+			  ((9 * new_itr) + q_vector->itr);
 
 		/* save the algorithm value here */
-		q_vector->eitr = new_itr;
+		q_vector->itr = new_itr & IXGBE_MAX_EITR;
 
 		ixgbe_write_eitr(q_vector);
 	}
@@ -1755,6 +1751,39 @@ static void ixgbe_check_fan_failure(struct ixgbe_adapter *adapter, u32 eicr)
 	}
 }
 
+static void ixgbe_check_overtemp_event(struct ixgbe_adapter *adapter, u32 eicr)
+{
+	if (!(adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE))
+		return;
+
+	switch (adapter->hw.mac.type) {
+	case ixgbe_mac_82599EB:
+		/*
+		 * Need to check link state so complete overtemp check
+		 * on service task
+		 */
+		if (((eicr & IXGBE_EICR_GPI_SDP0) || (eicr & IXGBE_EICR_LSC)) &&
+		    (!test_bit(__IXGBE_DOWN, &adapter->state))) {
+			adapter->interrupt_event = eicr;
+			adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_EVENT;
+			ixgbe_service_event_schedule(adapter);
+			return;
+		}
+		return;
+	case ixgbe_mac_X540:
+		if (!(eicr & IXGBE_EICR_TS))
+			return;
+		break;
+	default:
+		return;
+	}
+
+	e_crit(drv,
+	       "Network adapter has been stopped because it has over heated. "
+	       "Restart the computer. If the problem persists, "
+	       "power off the system and replace the adapter\n");
+}
+
 static void ixgbe_check_sfp_event(struct ixgbe_adapter *adapter, u32 eicr)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
@@ -1858,7 +1887,16 @@ static inline void ixgbe_irq_enable(struct ixgbe_adapter *adapter, bool queues,
 		mask &= ~IXGBE_EIMS_LSC;
 
 	if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE)
+		switch (adapter->hw.mac.type) {
+		case ixgbe_mac_82599EB:
 			mask |= IXGBE_EIMS_GPI_SDP0;
+			break;
+		case ixgbe_mac_X540:
+			mask |= IXGBE_EIMS_TS;
+			break;
+		default:
+			break;
+		}
 	if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE)
 		mask |= IXGBE_EIMS_GPI_SDP1;
 	switch (adapter->hw.mac.type) {
@@ -1928,14 +1966,7 @@ static irqreturn_t ixgbe_msix_other(int irq, void *data)
 			}
 		}
 		ixgbe_check_sfp_event(adapter, eicr);
-		if ((adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) &&
-		    ((eicr & IXGBE_EICR_GPI_SDP0) || (eicr & IXGBE_EICR_LSC))) {
-			if (!test_bit(__IXGBE_DOWN, &adapter->state)) {
-				adapter->interrupt_event = eicr;
-				adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_EVENT;
-				ixgbe_service_event_schedule(adapter);
-			}
-		}
+		ixgbe_check_overtemp_event(adapter, eicr);
 		break;
 	default:
 		break;
@@ -2145,14 +2176,12 @@ static irqreturn_t ixgbe_intr(int irq, void *data)
 	switch (hw->mac.type) {
 	case ixgbe_mac_82599EB:
 		ixgbe_check_sfp_event(adapter, eicr);
-		if ((adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) &&
-		    ((eicr & IXGBE_EICR_GPI_SDP0) || (eicr & IXGBE_EICR_LSC))) {
-			if (!test_bit(__IXGBE_DOWN, &adapter->state)) {
-				adapter->interrupt_event = eicr;
-				adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_EVENT;
-				ixgbe_service_event_schedule(adapter);
-			}
-		}
+		/* Fall through */
+	case ixgbe_mac_X540:
+		if (eicr & IXGBE_EICR_ECC)
+			e_info(link, "Received unrecoverable ECC err, please "
+				     "reboot\n");
+		ixgbe_check_overtemp_event(adapter, eicr);
 		break;
 	default:
 		break;
@@ -2301,10 +2330,15 @@ static inline void ixgbe_irq_disable(struct ixgbe_adapter *adapter)
  **/
 static void ixgbe_configure_msi_and_legacy(struct ixgbe_adapter *adapter)
 {
-	struct ixgbe_hw *hw = &adapter->hw;
+	struct ixgbe_q_vector *q_vector = adapter->q_vector[0];
+
+	/* rx/tx vector */
+	if (adapter->rx_itr_setting == 1)
+		q_vector->itr = IXGBE_20K_ITR;
+	else
+		q_vector->itr = adapter->rx_itr_setting;
 
-	IXGBE_WRITE_REG(hw, IXGBE_EITR(0),
-			EITR_INTS_PER_SEC_TO_REG(adapter->rx_eitr_param));
+	ixgbe_write_eitr(q_vector);
 
 	ixgbe_set_ivar(adapter, 0, 0, 0);
 	ixgbe_set_ivar(adapter, 1, 0, 0);
@@ -3350,8 +3384,127 @@ static void ixgbe_configure_dcb(struct ixgbe_adapter *adapter)
 		IXGBE_WRITE_REG(hw, IXGBE_RQTC, reg);
 	}
 }
+#endif
+
+/* Additional bittime to account for IXGBE framing */
+#define IXGBE_ETH_FRAMING 20
+
+/*
+ * ixgbe_hpbthresh - calculate high water mark for flow control
+ *
+ * @adapter: board private structure to calculate for
+ * @pb - packet buffer to calculate
+ */
+static int ixgbe_hpbthresh(struct ixgbe_adapter *adapter, int pb)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	struct net_device *dev = adapter->netdev;
+	int link, tc, kb, marker;
+	u32 dv_id, rx_pba;
+
+	/* Calculate max LAN frame size */
+	tc = link = dev->mtu + ETH_HLEN + ETH_FCS_LEN + IXGBE_ETH_FRAMING;
+
+#ifdef IXGBE_FCOE
+	/* FCoE traffic class uses FCOE jumbo frames */
+	if (dev->features & NETIF_F_FCOE_MTU) {
+		int fcoe_pb = 0;
+
+#ifdef CONFIG_IXGBE_DCB
+		fcoe_pb = netdev_get_prio_tc_map(dev, adapter->fcoe.up);
 
 #endif
+		if (fcoe_pb == pb && tc < IXGBE_FCOE_JUMBO_FRAME_SIZE)
+			tc = IXGBE_FCOE_JUMBO_FRAME_SIZE;
+	}
+#endif
+
+	/* Calculate delay value for device */
+	switch (hw->mac.type) {
+	case ixgbe_mac_X540:
+		dv_id = IXGBE_DV_X540(link, tc);
+		break;
+	default:
+		dv_id = IXGBE_DV(link, tc);
+		break;
+	}
+
+	/* Loopback switch introduces additional latency */
+	if (adapter->flags & IXGBE_FLAG_SRIOV_ENABLED)
+		dv_id += IXGBE_B2BT(tc);
+
+	/* Delay value is calculated in bit times convert to KB */
+	kb = IXGBE_BT2KB(dv_id);
+	rx_pba = IXGBE_READ_REG(hw, IXGBE_RXPBSIZE(pb)) >> 10;
+
+	marker = rx_pba - kb;
+
+	/* It is possible that the packet buffer is not large enough
+	 * to provide required headroom. In this case throw an error
+	 * to user and a do the best we can.
+	 */
+	if (marker < 0) {
+		e_warn(drv, "Packet Buffer(%i) can not provide enough"
+			    "headroom to support flow control."
+			    "Decrease MTU or number of traffic classes\n", pb);
+		marker = tc + 1;
+	}
+
+	return marker;
+}
+
+/*
+ * ixgbe_lpbthresh - calculate low water mark for for flow control
+ *
+ * @adapter: board private structure to calculate for
+ * @pb - packet buffer to calculate
+ */
+static int ixgbe_lpbthresh(struct ixgbe_adapter *adapter)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	struct net_device *dev = adapter->netdev;
+	int tc;
+	u32 dv_id;
+
+	/* Calculate max LAN frame size */
+	tc = dev->mtu + ETH_HLEN + ETH_FCS_LEN;
+
+	/* Calculate delay value for device */
+	switch (hw->mac.type) {
+	case ixgbe_mac_X540:
+		dv_id = IXGBE_LOW_DV_X540(tc);
+		break;
+	default:
+		dv_id = IXGBE_LOW_DV(tc);
+		break;
+	}
+
+	/* Delay value is calculated in bit times convert to KB */
+	return IXGBE_BT2KB(dv_id);
+}
+
+/*
+ * ixgbe_pbthresh_setup - calculate and setup high low water marks
+ */
+static void ixgbe_pbthresh_setup(struct ixgbe_adapter *adapter)
+{
+	struct ixgbe_hw *hw = &adapter->hw;
+	int num_tc = netdev_get_num_tc(adapter->netdev);
+	int i;
+
+	if (!num_tc)
+		num_tc = 1;
+
+	hw->fc.low_water = ixgbe_lpbthresh(adapter);
+
+	for (i = 0; i < num_tc; i++) {
+		hw->fc.high_water[i] = ixgbe_hpbthresh(adapter, i);
+
+		/* Low water marks must not be larger than high water marks */
+		if (hw->fc.low_water > hw->fc.high_water[i])
+			hw->fc.low_water = 0;
+	}
+}
 
 static void ixgbe_configure_pb(struct ixgbe_adapter *adapter)
 {
@@ -3366,6 +3519,7 @@ static void ixgbe_configure_pb(struct ixgbe_adapter *adapter)
 		hdrm = 0;
 
 	hw->mac.ops.set_rxpba(hw, tc, hdrm, PBA_STRATEGY_EQUAL);
+	ixgbe_pbthresh_setup(adapter);
 }
 
 static void ixgbe_fdir_filter_restore(struct ixgbe_adapter *adapter)
@@ -3530,8 +3684,18 @@ static void ixgbe_setup_gpie(struct ixgbe_adapter *adapter)
 	}
 
 	/* Enable Thermal over heat sensor interrupt */
-	if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE)
+	if (adapter->flags2 & IXGBE_FLAG2_TEMP_SENSOR_CAPABLE) {
+		switch (adapter->hw.mac.type) {
+		case ixgbe_mac_82599EB:
 			gpie |= IXGBE_SDP0_GPIEN;
+			break;
+		case ixgbe_mac_X540:
+			gpie |= IXGBE_EIMS_TS;
+			break;
+		default:
+			break;
+		}
+	}
 
 	/* Enable fan failure interrupt */
 	if (adapter->flags & IXGBE_FLAG_FAN_FAIL_CAPABLE)
@@ -4613,12 +4777,6 @@ static int ixgbe_alloc_q_vectors(struct ixgbe_adapter *adapter)
 		if (!alloc_cpumask_var(&q_vector->affinity_mask, GFP_KERNEL))
 			goto err_out;
 		cpumask_set_cpu(v_idx, q_vector->affinity_mask);
-
-		if (q_vector->tx.count && !q_vector->rx.count)
-			q_vector->eitr = adapter->tx_eitr_param;
-		else
-			q_vector->eitr = adapter->rx_eitr_param;
-
 		netif_napi_add(adapter->netdev, &q_vector->napi,
 			       ixgbe_poll, 64);
 		adapter->q_vector[v_idx] = q_vector;
@@ -4774,13 +4932,11 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
 {
 	struct ixgbe_hw *hw = &adapter->hw;
 	struct pci_dev *pdev = adapter->pdev;
-	struct net_device *dev = adapter->netdev;
 	unsigned int rss;
 #ifdef CONFIG_IXGBE_DCB
 	int j;
 	struct tc_configuration *tc;
 #endif
-	int max_frame = dev->mtu + ETH_HLEN + ETH_FCS_LEN;
 
 	/* PCI config space info */
 
@@ -4800,8 +4956,9 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
 			adapter->flags |= IXGBE_FLAG_FAN_FAIL_CAPABLE;
 		adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82598;
 		break;
-	case ixgbe_mac_82599EB:
 	case ixgbe_mac_X540:
+		adapter->flags2 |= IXGBE_FLAG2_TEMP_SENSOR_CAPABLE;
+	case ixgbe_mac_82599EB:
 		adapter->max_msix_q_vectors = MAX_MSIX_Q_VECTORS_82599;
 		adapter->flags2 |= IXGBE_FLAG2_RSC_CAPABLE;
 		adapter->flags2 |= IXGBE_FLAG2_RSC_ENABLED;
@@ -4856,17 +5013,14 @@ static int __devinit ixgbe_sw_init(struct ixgbe_adapter *adapter)
 #ifdef CONFIG_DCB
 	adapter->last_lfc_mode = hw->fc.current_mode;
 #endif
-	hw->fc.high_water = FC_HIGH_WATER(max_frame);
-	hw->fc.low_water = FC_LOW_WATER(max_frame);
+	ixgbe_pbthresh_setup(adapter);
 	hw->fc.pause_time = IXGBE_DEFAULT_FCPAUSE;
 	hw->fc.send_xon = true;
 	hw->fc.disable_fc_autoneg = false;
 
 	/* enable itr by default in dynamic mode */
 	adapter->rx_itr_setting = 1;
-	adapter->rx_eitr_param = 20000;
 	adapter->tx_itr_setting = 1;
-	adapter->tx_eitr_param = 10000;
 
 	/* set defaults for eitr in MegaBytes */
 	adapter->eitr_low = 10;
@@ -5126,9 +5280,6 @@ static int ixgbe_change_mtu(struct net_device *netdev, int new_mtu)
 	/* must set new MTU before calling down or up */
 	netdev->mtu = new_mtu;
 
-	hw->fc.high_water = FC_HIGH_WATER(max_frame);
-	hw->fc.low_water = FC_LOW_WATER(max_frame);
-
 	if (netif_running(netdev))
 		ixgbe_reinit_locked(adapter);
 

drivers/net/ethernet/intel/ixgbe/ixgbe_type.h

@@ -404,6 +404,7 @@
 #define IXGBE_WUPL_LENGTH_MASK 0xFFFF
 
 /* DCB registers */
+#define MAX_TRAFFIC_CLASS        8
 #define IXGBE_RMCS      0x03D00
 #define IXGBE_DPMCS     0x07F40
 #define IXGBE_PDPMCS    0x0CD00
@@ -1279,6 +1280,7 @@ enum {
 #define IXGBE_EICR_LSC          0x00100000 /* Link Status Change */
 #define IXGBE_EICR_LINKSEC      0x00200000 /* PN Threshold */
 #define IXGBE_EICR_MNG          0x00400000 /* Manageability Event Interrupt */
+#define IXGBE_EICR_TS           0x00800000 /* Thermal Sensor Event */
 #define IXGBE_EICR_GPI_SDP0     0x01000000 /* Gen Purpose Interrupt on SDP0 */
 #define IXGBE_EICR_GPI_SDP1     0x02000000 /* Gen Purpose Interrupt on SDP1 */
 #define IXGBE_EICR_GPI_SDP2     0x04000000 /* Gen Purpose Interrupt on SDP2 */
@@ -1313,6 +1315,7 @@ enum {
 #define IXGBE_EIMS_MAILBOX      IXGBE_EICR_MAILBOX   /* VF to PF Mailbox Int */
 #define IXGBE_EIMS_LSC          IXGBE_EICR_LSC       /* Link Status Change */
 #define IXGBE_EIMS_MNG          IXGBE_EICR_MNG       /* MNG Event Interrupt */
+#define IXGBE_EIMS_TS           IXGBE_EICR_TS        /* Thermel Sensor Event */
 #define IXGBE_EIMS_GPI_SDP0     IXGBE_EICR_GPI_SDP0  /* SDP0 Gen Purpose Int */
 #define IXGBE_EIMS_GPI_SDP1     IXGBE_EICR_GPI_SDP1  /* SDP1 Gen Purpose Int */
 #define IXGBE_EIMS_GPI_SDP2     IXGBE_EICR_GPI_SDP2  /* SDP2 Gen Purpose Int */
@@ -2323,13 +2326,60 @@ typedef u32 ixgbe_physical_layer;
 #define IXGBE_PHYSICAL_LAYER_10GBASE_XAUI 0x1000
 #define IXGBE_PHYSICAL_LAYER_SFP_ACTIVE_DA 0x2000
 
-/* Flow Control Macros */
-#define PAUSE_RTT	8
-#define PAUSE_MTU(MTU)	((MTU + 1024 - 1) / 1024)
+/* Flow Control Data Sheet defined values
+ * Calculation and defines taken from 802.1bb Annex O
+ */
+
+/* BitTimes (BT) conversion */
+#define IXGBE_BT2KB(BT) ((BT + 1023) / (8 * 1024))
+#define IXGBE_B2BT(BT) (BT * 8)
+
+/* Calculate Delay to respond to PFC */
+#define IXGBE_PFC_D	672
+
+/* Calculate Cable Delay */
+#define IXGBE_CABLE_DC	5556 /* Delay Copper */
+#define IXGBE_CABLE_DO	5000 /* Delay Optical */
+
+/* Calculate Interface Delay X540 */
+#define IXGBE_PHY_DC	25600	/* Delay 10G BASET */
+#define IXGBE_MAC_DC	8192	/* Delay Copper XAUI interface */
+#define IXGBE_XAUI_DC	(2 * 2048) /* Delay Copper Phy */
+
+#define IXGBE_ID_X540	(IXGBE_MAC_DC + IXGBE_XAUI_DC + IXGBE_PHY_DC)
+
+/* Calculate Interface Delay 82598, 82599 */
+#define IXGBE_PHY_D	12800
+#define IXGBE_MAC_D	4096
+#define IXGBE_XAUI_D	(2 * 1024)
+
+#define IXGBE_ID	(IXGBE_MAC_D + IXGBE_XAUI_D + IXGBE_PHY_D)
+
+/* Calculate Delay incurred from higher layer */
+#define IXGBE_HD	6144
+
+/* Calculate PCI Bus delay for low thresholds */
+#define IXGBE_PCI_DELAY	10000
+
+/* Calculate X540 delay value in bit times */
+#define IXGBE_FILL_RATE (36 / 25)
+
+#define IXGBE_DV_X540(LINK, TC) (IXGBE_FILL_RATE * \
+				 (IXGBE_B2BT(LINK) + IXGBE_PFC_D + \
+				 (2 * IXGBE_CABLE_DC) + \
+				 (2 * IXGBE_ID_X540) + \
+				 IXGBE_HD + IXGBE_B2BT(TC)))
+
+/* Calculate 82599, 82598 delay value in bit times */
+#define IXGBE_DV(LINK, TC) (IXGBE_FILL_RATE * \
+			    (IXGBE_B2BT(LINK) + IXGBE_PFC_D + \
+			    (2 * IXGBE_CABLE_DC) + (2 * IXGBE_ID) + \
+			    IXGBE_HD + IXGBE_B2BT(TC)))
 
-#define FC_HIGH_WATER(MTU) ((((PAUSE_RTT + PAUSE_MTU(MTU)) * 144) + 99) / 100 +\
-				PAUSE_MTU(MTU))
-#define FC_LOW_WATER(MTU)  (2 * (2 * PAUSE_MTU(MTU) + PAUSE_RTT))
+/* Calculate low threshold delay values */
+#define IXGBE_LOW_DV_X540(TC) (2 * IXGBE_B2BT(TC) + \
+			       (IXGBE_FILL_RATE * IXGBE_PCI_DELAY))
+#define IXGBE_LOW_DV(TC)      (2 * IXGBE_LOW_DV_X540(TC))
 
 /* Software ATR hash keys */
 #define IXGBE_ATR_BUCKET_HASH_KEY    0x3DAD14E2
@@ -2548,7 +2598,7 @@ struct ixgbe_bus_info {
 
 /* Flow control parameters */
 struct ixgbe_fc_info {
-	u32 high_water; /* Flow Control High-water */
+	u32 high_water[MAX_TRAFFIC_CLASS]; /* Flow Control High-water */
 	u32 low_water; /* Flow Control Low-water */
 	u16 pause_time; /* Flow Control Pause timer */
 	bool send_xon; /* Flow control send XON */

drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c

@@ -293,12 +293,10 @@ static void ixgbevf_receive_skb(struct ixgbevf_q_vector *q_vector,
 {
 	struct ixgbevf_adapter *adapter = q_vector->adapter;
 	bool is_vlan = (status & IXGBE_RXD_STAT_VP);
-
-	if (is_vlan) {
 	u16 tag = le16_to_cpu(rx_desc->wb.upper.vlan);
 
+	if (is_vlan && test_bit(tag, adapter->active_vlans))
 		__vlan_hwaccel_put_tag(skb, tag);
-	}
 
 	if (!(adapter->flags & IXGBE_FLAG_IN_NETPOLL))
 			napi_gro_receive(&q_vector->napi, skb);