net: ethernet: Add helper to remove a supported link mode

Some MAC hardware cannot support a subset of link modes. e.g. often
1Gbps Full duplex is supported, but Half duplex is not. Add a helper
to remove such a link mode.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/ethernet/apm/xgene/xgene_enet_hw.c

@@ -895,9 +895,9 @@ int xgene_enet_phy_connect(struct net_device *ndev)
 	}
 
 	pdata->phy_speed = SPEED_UNKNOWN;
-	phy_dev->supported &= ~SUPPORTED_10baseT_Half &
-			      ~SUPPORTED_100baseT_Half &
-			      ~SUPPORTED_1000baseT_Half;
+	phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+	phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+	phy_remove_link_mode(phy_dev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 	phy_dev->supported |= SUPPORTED_Pause |
 			      SUPPORTED_Asym_Pause;
 	phy_dev->advertising = phy_dev->supported;

drivers/net/ethernet/cadence/macb_main.c

@@ -549,9 +549,8 @@ static int macb_mii_probe(struct net_device *dev)
 		phy_set_max_speed(phydev, SPEED_100);
 
 	if (bp->caps & MACB_CAPS_NO_GIGABIT_HALF)
-		phydev->supported &= ~SUPPORTED_1000baseT_Half;
-
-	phydev->advertising = phydev->supported;
+		phy_remove_link_mode(phydev,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 
 	bp->link = 0;
 	bp->speed = 0;

drivers/net/ethernet/freescale/fec_main.c

@@ -1947,7 +1947,8 @@ static int fec_enet_mii_probe(struct net_device *ndev)
 	/* mask with MAC supported features */
 	if (fep->quirks & FEC_QUIRK_HAS_GBIT) {
 		phy_set_max_speed(phy_dev, 1000);
-		phy_dev->supported &= ~SUPPORTED_1000baseT_Half;
+		phy_remove_link_mode(phy_dev,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 #if !defined(CONFIG_M5272)
 		phy_dev->supported |= SUPPORTED_Pause;
 #endif

drivers/net/ethernet/microchip/lan743x_main.c

@@ -1013,7 +1013,7 @@ static int lan743x_phy_open(struct lan743x_adapter *adapter)
 		goto return_error;
 
 	/* MAC doesn't support 1000T Half */
-	phydev->supported &= ~SUPPORTED_1000baseT_Half;
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 
 	/* support both flow controls */
 	phy->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);

drivers/net/ethernet/renesas/ravb_main.c

@@ -1074,7 +1074,8 @@ static int ravb_phy_init(struct net_device *ndev)
 	}
 
 	/* 10BASE is not supported */
-	phydev->supported &= ~PHY_10BT_FEATURES;
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_10baseT_Full_BIT);
 
 	phy_attached_info(phydev);
 

drivers/net/ethernet/stmicro/stmmac/stmmac_main.c

@@ -993,10 +993,14 @@ static int stmmac_init_phy(struct net_device *dev)
 	 * Half-duplex mode not supported with multiqueue
 	 * half-duplex can only works with single queue
 	 */
-	if (tx_cnt > 1)
-		phydev->supported &= ~(SUPPORTED_1000baseT_Half |
-				       SUPPORTED_100baseT_Half |
-				       SUPPORTED_10baseT_Half);
+	if (tx_cnt > 1) {
+		phy_remove_link_mode(phydev,
+				     ETHTOOL_LINK_MODE_10baseT_Half_BIT);
+		phy_remove_link_mode(phydev,
+				     ETHTOOL_LINK_MODE_100baseT_Half_BIT);
+		phy_remove_link_mode(phydev,
+				     ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
+	}
 
 	/*
 	 * Broken HW is sometimes missing the pull-up resistor on the

drivers/net/phy/phy_device.c

@@ -1765,6 +1765,24 @@ int phy_set_max_speed(struct phy_device *phydev, u32 max_speed)
 }
 EXPORT_SYMBOL(phy_set_max_speed);
 
+/**
+ * phy_remove_link_mode - Remove a supported link mode
+ * @phydev: phy_device structure to remove link mode from
+ * @link_mode: Link mode to be removed
+ *
+ * Description: Some MACs don't support all link modes which the PHY
+ * does.  e.g. a 1G MAC often does not support 1000Half. Add a helper
+ * to remove a link mode.
+ */
+void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode)
+{
+	WARN_ON(link_mode > 31);
+
+	phydev->supported &= ~BIT(link_mode);
+	phydev->advertising = phydev->supported;
+}
+EXPORT_SYMBOL(phy_remove_link_mode);
+
 static void of_set_phy_supported(struct phy_device *phydev)
 {
 	struct device_node *node = phydev->mdio.dev.of_node;

drivers/net/usb/lan78xx.c

@@ -2166,7 +2166,7 @@ static int lan78xx_phy_init(struct lan78xx_net *dev)
 	}
 
 	/* MAC doesn't support 1000T Half */
-	phydev->supported &= ~SUPPORTED_1000baseT_Half;
+	phy_remove_link_mode(phydev, ETHTOOL_LINK_MODE_1000baseT_Half_BIT);
 
 	/* support both flow controls */
 	dev->fc_request_control = (FLOW_CTRL_RX | FLOW_CTRL_TX);

include/linux/phy.h

@@ -1049,6 +1049,7 @@ int phy_mii_ioctl(struct phy_device *phydev, struct ifreq *ifr, int cmd);
 int phy_start_interrupts(struct phy_device *phydev);
 void phy_print_status(struct phy_device *phydev);
 int phy_set_max_speed(struct phy_device *phydev, u32 max_speed);
+void phy_remove_link_mode(struct phy_device *phydev, u32 link_mode);
 
 int phy_register_fixup(const char *bus_id, u32 phy_uid, u32 phy_uid_mask,
 		       int (*run)(struct phy_device *));