Merge branch 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging

* 'i2c-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jdelvare/staging:
  i2c-stub: Documentation update
  i2c-stub: Allow user to disable some commands
  i2c-stub: Implement I2C block support
  i2c: Refactor for_each callbacks
  i2c-i801: Retry on lost arbitration
  i2c: Remove big kernel lock from i2cdev_open
  ics932s401: Clean up detect function
  i2c: Simplify i2c_detect_address
  i2c: Drop probe, ignore and force module parameters
  i2c: Add missing __devinit markers to old i2c adapter drivers
  i2c: Bus drivers don't have to support I2C_M_REV_DIR_ADDR
  i2c: Prevent priority inversion on top of bus lock
  i2c-voodoo3: Delete
  i2c-powermac: Drop temporary name buffer
  i2c-powermac: Include the i2c_adapter in struct pmac_i2c_bus
  i2c-powermac: Log errors
  i2c-powermac: Refactor i2c_powermac_smbus_xfer
  i2c-powermac: Reject unsupported I2C transactions
  i2c/chips: Move ds1682 to drivers/misc

Documentation/feature-removal-schedule.txt

@@ -407,15 +407,6 @@ Who:	Alex Chiang <achiang@hp.com>
 
 ---------------------------
 
-What:	i2c-voodoo3 driver
-When:	October 2009
-Why:	Superseded by tdfxfb. I2C/DDC support used to live in a separate
-	driver but this caused driver conflicts.
-Who:	Jean Delvare <khali@linux-fr.org>
-	Krzysztof Helt <krzysztof.h1@wp.pl>
-
----------------------------
-
 What:	CONFIG_RFKILL_INPUT
 When:	2.6.33
 Why:	Should be implemented in userspace, policy daemon.

Documentation/i2c/busses/i2c-voodoo3

-Kernel driver i2c-voodoo3
-
-Supported adapters:
-  * 3dfx Voodoo3 based cards
-  * Voodoo Banshee based cards
-
-Authors: 
-	Frodo Looijaard <frodol@dds.nl>, 
-	Philip Edelbrock <phil@netroedge.com>, 
-	Ralph Metzler <rjkm@thp.uni-koeln.de>,
-	Mark D. Studebaker <mdsxyz123@yahoo.com>
-
-Main contact: Philip Edelbrock <phil@netroedge.com>
-	
-The code is based upon Ralph's test code (he did the hard stuff ;')
-
-Description
------------
-
-The 3dfx Voodoo3 chip contains two I2C interfaces (aka a I2C 'master' or
-'host'). 
-
-The first interface is used for DDC (Data Display Channel) which is a
-serial channel through the VGA monitor connector to a DDC-compliant
-monitor. This interface is defined by the Video Electronics Standards
-Association (VESA). The standards are available for purchase at
-http://www.vesa.org .
-
-The second interface is a general-purpose I2C bus. The intent by 3dfx was
-to allow manufacturers to add extra chips to the video card such as a
-TV-out chip such as the BT869 or possibly even I2C based temperature
-sensors like the ADM1021 or LM75.
-
-Stability
----------
-
-Seems to be stable on the test machine, but needs more testing on other
-machines. Simultaneous accesses of the DDC and I2C busses may cause errors.
-
-Supported Devices
------------------
-
-Specifically, this driver was written and tested on the '3dfx Voodoo3 AGP
-3000' which has a tv-out feature (s-video or composite).  According to the
-docs and discussions, this code should work for any Voodoo3 based cards as
-well as Voodoo Banshee based cards.  The DDC interface has been tested on a
-Voodoo Banshee card.
-	
-Issues
-------
-
-Probably many, but it seems to work OK on my system. :')
-
-
-External Device Connection
---------------------------
-
-The digital video input jumpers give availability to the I2C bus. 
-Specifically, pins 13 and 25 (bottom row middle, and bottom right-end) are     
-the I2C clock and I2C data lines, respectively. +5V and GND are probably
-also easily available making the addition of extra I2C/SMBus devices easy
-to implement.

Documentation/i2c/i2c-stub

@@ -2,9 +2,9 @@ MODULE: i2c-stub
 
 DESCRIPTION:
 
-This module is a very simple fake I2C/SMBus driver.  It implements four
-types of SMBus commands: write quick, (r/w) byte, (r/w) byte data, and
-(r/w) word data.
+This module is a very simple fake I2C/SMBus driver.  It implements five
+types of SMBus commands: write quick, (r/w) byte, (r/w) byte data, (r/w)
+word data, and (r/w) I2C block data.
 
 You need to provide chip addresses as a module parameter when loading this
 driver, which will then only react to SMBus commands to these addresses.
@@ -21,8 +21,8 @@ EEPROMs, among others.
 
 The typical use-case is like this:
 	1. load this module
-	2. use i2cset (from lm_sensors project) to pre-load some data
-	3. load the target sensors chip driver module
+	2. use i2cset (from the i2c-tools project) to pre-load some data
+	3. load the target chip driver module
 	4. observe its behavior in the kernel log
 
 There's a script named i2c-stub-from-dump in the i2c-tools package which
@@ -33,6 +33,12 @@ PARAMETERS:
 int chip_addr[10]:
 	The SMBus addresses to emulate chips at.
 
+unsigned long functionality:
+	Functionality override, to disable some commands. See I2C_FUNC_*
+	constants in <linux/i2c.h> for the suitable values. For example,
+	value 0x1f0000 would only enable the quick, byte and byte data
+	commands.
+
 CAVEATS:
 
 If your target driver polls some byte or word waiting for it to change, the

Documentation/i2c/old-module-parameters

+I2C device driver binding control from user-space
+=================================================
+
+Up to kernel 2.6.32, many i2c drivers used helper macros provided by
+<linux/i2c.h> which created standard module parameters to let the user
+control how the driver would probe i2c buses and attach to devices. These
+parameters were known as "probe" (to let the driver probe for an extra
+address), "force" (to forcibly attach the driver to a given device) and
+"ignore" (to prevent a driver from probing a given address).
+
+With the conversion of the i2c subsystem to the standard device driver
+binding model, it became clear that these per-module parameters were no
+longer needed, and that a centralized implementation was possible. The new,
+sysfs-based interface is described in the documentation file
+"instantiating-devices", section "Method 4: Instantiate from user-space".
+
+Below is a mapping from the old module parameters to the new interface.
+
+Attaching a driver to an I2C device
+-----------------------------------
+
+Old method (module parameters):
+# modprobe <driver> probe=1,0x2d
+# modprobe <driver> force=1,0x2d
+# modprobe <driver> force_<device>=1,0x2d
+
+New method (sysfs interface):
+# echo <device> 0x2d > /sys/bus/i2c/devices/i2c-1/new_device
+
+Preventing a driver from attaching to an I2C device
+---------------------------------------------------
+
+Old method (module parameters):
+# modprobe <driver> ignore=1,0x2f
+
+New method (sysfs interface):
+# echo dummy 0x2f > /sys/bus/i2c/devices/i2c-1/new_device
+# modprobe <driver>
+
+Of course, it is important to instantiate the "dummy" device before loading
+the driver. The dummy device will be handled by i2c-core itself, preventing
+other drivers from binding to it later on. If there is a real device at the
+problematic address, and you want another driver to bind to it, then simply
+pass the name of the device in question instead of "dummy".

arch/powerpc/include/asm/pmac_low_i2c.h

@@ -72,11 +72,7 @@ extern int pmac_i2c_get_type(struct pmac_i2c_bus *bus);
 extern int pmac_i2c_get_flags(struct pmac_i2c_bus *bus);
 extern int pmac_i2c_get_channel(struct pmac_i2c_bus *bus);
 
-/* i2c layer adapter attach/detach */
-extern void pmac_i2c_attach_adapter(struct pmac_i2c_bus *bus,
-				    struct i2c_adapter *adapter);
-extern void pmac_i2c_detach_adapter(struct pmac_i2c_bus *bus,
-				    struct i2c_adapter *adapter);
+/* i2c layer adapter helpers */
 extern struct i2c_adapter *pmac_i2c_get_adapter(struct pmac_i2c_bus *bus);
 extern struct pmac_i2c_bus *pmac_i2c_adapter_to_bus(struct i2c_adapter *adapter);
 

arch/powerpc/platforms/powermac/low_i2c.c

@@ -42,6 +42,7 @@
 #include <linux/interrupt.h>
 #include <linux/timer.h>
 #include <linux/mutex.h>
+#include <linux/i2c.h>
 #include <asm/keylargo.h>
 #include <asm/uninorth.h>
 #include <asm/io.h>
@@ -80,7 +81,7 @@ struct pmac_i2c_bus
 	struct device_node	*busnode;
 	int			type;
 	int			flags;
-	struct i2c_adapter	*adapter;
+	struct i2c_adapter	adapter;
 	void			*hostdata;
 	int			channel;	/* some hosts have multiple */
 	int			mode;		/* current mode */
@@ -1014,25 +1015,9 @@ int pmac_i2c_get_channel(struct pmac_i2c_bus *bus)
 EXPORT_SYMBOL_GPL(pmac_i2c_get_channel);
 
 
-void pmac_i2c_attach_adapter(struct pmac_i2c_bus *bus,
-			     struct i2c_adapter *adapter)
-{
-	WARN_ON(bus->adapter != NULL);
-	bus->adapter = adapter;
-}
-EXPORT_SYMBOL_GPL(pmac_i2c_attach_adapter);
-
-void pmac_i2c_detach_adapter(struct pmac_i2c_bus *bus,
-			     struct i2c_adapter *adapter)
-{
-	WARN_ON(bus->adapter != adapter);
-	bus->adapter = NULL;
-}
-EXPORT_SYMBOL_GPL(pmac_i2c_detach_adapter);
-
 struct i2c_adapter *pmac_i2c_get_adapter(struct pmac_i2c_bus *bus)
 {
-	return bus->adapter;
+	return &bus->adapter;
 }
 EXPORT_SYMBOL_GPL(pmac_i2c_get_adapter);
 
@@ -1041,7 +1026,7 @@ struct pmac_i2c_bus *pmac_i2c_adapter_to_bus(struct i2c_adapter *adapter)
 	struct pmac_i2c_bus *bus;
 
 	list_for_each_entry(bus, &pmac_i2c_busses, link)
-		if (bus->adapter == adapter)
+		if (&bus->adapter == adapter)
 			return bus;
 	return NULL;
 }
@@ -1053,7 +1038,7 @@ int pmac_i2c_match_adapter(struct device_node *dev, struct i2c_adapter *adapter)
 
 	if (bus == NULL)
 		return 0;
-	return (bus->adapter == adapter);
+	return (&bus->adapter == adapter);
 }
 EXPORT_SYMBOL_GPL(pmac_i2c_match_adapter);
 

drivers/i2c/Kconfig

@@ -5,6 +5,7 @@
 menuconfig I2C
 	tristate "I2C support"
 	depends on HAS_IOMEM
+	select RT_MUTEXES
 	---help---
 	  I2C (pronounce: I-square-C) is a slow serial bus protocol used in
 	  many micro controller applications and developed by Philips.  SMBus,

drivers/i2c/busses/Kconfig

@@ -640,22 +640,6 @@ config I2C_TINY_USB
 	  This driver can also be built as a module.  If so, the module
 	  will be called i2c-tiny-usb.
 
-comment "Graphics adapter I2C/DDC channel drivers"
-	depends on PCI
-
-config I2C_VOODOO3
-	tristate "Voodoo 3 (DEPRECATED)"
-	depends on PCI
-	select I2C_ALGOBIT
-	help
-	  If you say yes to this option, support will be included for the
-	  Voodoo 3 I2C interface. This driver is deprecated and you should
-	  use the tdfxfb driver instead, which additionally provides
-	  framebuffer support.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called i2c-voodoo3.
-
 comment "Other I2C/SMBus bus drivers"
 
 config I2C_ACORN

drivers/i2c/busses/Makefile

@@ -61,9 +61,6 @@ obj-$(CONFIG_I2C_PARPORT_LIGHT)	+= i2c-parport-light.o
 obj-$(CONFIG_I2C_TAOS_EVM)	+= i2c-taos-evm.o
 obj-$(CONFIG_I2C_TINY_USB)	+= i2c-tiny-usb.o
 
-# Graphics adapter I2C/DDC channel drivers
-obj-$(CONFIG_I2C_VOODOO3)	+= i2c-voodoo3.o
-
 # Other I2C/SMBus bus drivers
 obj-$(CONFIG_I2C_ACORN)		+= i2c-acorn.o
 obj-$(CONFIG_I2C_ELEKTOR)	+= i2c-elektor.o

drivers/i2c/busses/i2c-ali1535.c

@@ -138,7 +138,7 @@ static unsigned short ali1535_smba;
    Note the differences between kernels with the old PCI BIOS interface and
    newer kernels with the real PCI interface. In compat.h some things are
    defined to make the transition easier. */
-static int ali1535_setup(struct pci_dev *dev)
+static int __devinit ali1535_setup(struct pci_dev *dev)
 {
 	int retval = -ENODEV;
 	unsigned char temp;

drivers/i2c/busses/i2c-ali15x3.c

@@ -131,7 +131,7 @@ MODULE_PARM_DESC(force_addr,
 static struct pci_driver ali15x3_driver;
 static unsigned short ali15x3_smba;
 
-static int ali15x3_setup(struct pci_dev *ALI15X3_dev)
+static int __devinit ali15x3_setup(struct pci_dev *ALI15X3_dev)
 {
 	u16 a;
 	unsigned char temp;

drivers/i2c/busses/i2c-i801.c

@@ -767,6 +767,9 @@ static int __devinit i801_probe(struct pci_dev *dev, const struct pci_device_id
 	/* set up the sysfs linkage to our parent device */
 	i801_adapter.dev.parent = &dev->dev;
 
+	/* Retry up to 3 times on lost arbitration */
+	i801_adapter.retries = 3;
+
 	snprintf(i801_adapter.name, sizeof(i801_adapter.name),
 		"SMBus I801 adapter at %04lx", i801_smba);
 	err = i2c_add_adapter(&i801_adapter);

drivers/i2c/busses/i2c-iop3xx.c

@@ -56,12 +56,6 @@ iic_cook_addr(struct i2c_msg *msg)
 	if (msg->flags & I2C_M_RD)
 		addr |= 1;
 
-	/*
-	 * Read or Write?
-	 */
-	if (msg->flags & I2C_M_REV_DIR_ADDR)
-		addr ^= 1;
-
 	return addr;   
 }
 

drivers/i2c/busses/i2c-mv64xxx.c

@@ -338,9 +338,6 @@ mv64xxx_i2c_prepare_for_io(struct mv64xxx_i2c_data *drv_data,
 	if (msg->flags & I2C_M_RD)
 		dir = 1;
 
-	if (msg->flags & I2C_M_REV_DIR_ADDR)
-		dir ^= 1;
-
 	if (msg->flags & I2C_M_TEN) {
 		drv_data->addr1 = 0xf0 | (((u32)msg->addr & 0x300) >> 7) | dir;
 		drv_data->addr2 = (u32)msg->addr & 0xff;

drivers/i2c/busses/i2c-powermac.c

@@ -49,48 +49,38 @@ static s32 i2c_powermac_smbus_xfer(	struct i2c_adapter*	adap,
 	int			rc = 0;
 	int			read = (read_write == I2C_SMBUS_READ);
 	int			addrdir = (addr << 1) | read;
+	int			mode, subsize, len;
+	u32			subaddr;
+	u8			*buf;
 	u8			local[2];
 
-	rc = pmac_i2c_open(bus, 0);
-	if (rc)
-		return rc;
+	if (size == I2C_SMBUS_QUICK || size == I2C_SMBUS_BYTE) {
+		mode = pmac_i2c_mode_std;
+		subsize = 0;
+		subaddr = 0;
+	} else {
+		mode = read ? pmac_i2c_mode_combined : pmac_i2c_mode_stdsub;
+		subsize = 1;
+		subaddr = command;
+	}
 
 	switch (size) {
         case I2C_SMBUS_QUICK:
-		rc = pmac_i2c_setmode(bus, pmac_i2c_mode_std);
-		if (rc)
-			goto bail;
-		rc = pmac_i2c_xfer(bus, addrdir, 0, 0, NULL, 0);
+		buf = NULL;
+		len = 0;
 	    	break;
         case I2C_SMBUS_BYTE:
-		rc = pmac_i2c_setmode(bus, pmac_i2c_mode_std);
-		if (rc)
-			goto bail;
-		rc = pmac_i2c_xfer(bus, addrdir, 0, 0, &data->byte, 1);
-	    	break;
         case I2C_SMBUS_BYTE_DATA:
-		rc = pmac_i2c_setmode(bus, read ?
-				      pmac_i2c_mode_combined :
-				      pmac_i2c_mode_stdsub);
-		if (rc)
-			goto bail;
-		rc = pmac_i2c_xfer(bus, addrdir, 1, command, &data->byte, 1);
+		buf = &data->byte;
+		len = 1;
 	    	break;
         case I2C_SMBUS_WORD_DATA:
-		rc = pmac_i2c_setmode(bus, read ?
-				      pmac_i2c_mode_combined :
-				      pmac_i2c_mode_stdsub);
-		if (rc)
-			goto bail;
 		if (!read) {
 			local[0] = data->word & 0xff;
 			local[1] = (data->word >> 8) & 0xff;
 		}
-		rc = pmac_i2c_xfer(bus, addrdir, 1, command, local, 2);
-		if (rc == 0 && read) {
-			data->word = ((u16)local[1]) << 8;
-			data->word |= local[0];
-		}
+		buf = local;
+		len = 2;
 	    	break;
 
 	/* Note that these are broken vs. the expected smbus API where
@@ -105,28 +95,44 @@ static s32 i2c_powermac_smbus_xfer(	struct i2c_adapter*	adap,
 	 * a repeat start/addr phase (but not stop in between)
 	 */
         case I2C_SMBUS_BLOCK_DATA:
-		rc = pmac_i2c_setmode(bus, read ?
-				      pmac_i2c_mode_combined :
-				      pmac_i2c_mode_stdsub);
-		if (rc)
-			goto bail;
-		rc = pmac_i2c_xfer(bus, addrdir, 1, command, data->block,
-				   data->block[0] + 1);
-
+		buf = data->block;
+		len = data->block[0] + 1;
 		break;
 	case I2C_SMBUS_I2C_BLOCK_DATA:
-		rc = pmac_i2c_setmode(bus, read ?
-				      pmac_i2c_mode_combined :
-				      pmac_i2c_mode_stdsub);
-		if (rc)
-			goto bail;
-		rc = pmac_i2c_xfer(bus, addrdir, 1, command,
-				   &data->block[1], data->block[0]);
+		buf = &data->block[1];
+		len = data->block[0];
 		break;
 
         default:
-	    	rc = -EINVAL;
+		return -EINVAL;
+	}
+
+	rc = pmac_i2c_open(bus, 0);
+	if (rc) {
+		dev_err(&adap->dev, "Failed to open I2C, err %d\n", rc);
+		return rc;
+	}
+
+	rc = pmac_i2c_setmode(bus, mode);
+	if (rc) {
+		dev_err(&adap->dev, "Failed to set I2C mode %d, err %d\n",
+			mode, rc);
+		goto bail;
 	}
+
+	rc = pmac_i2c_xfer(bus, addrdir, subsize, subaddr, buf, len);
+	if (rc) {
+		dev_err(&adap->dev,
+			"I2C transfer at 0x%02x failed, size %d, err %d\n",
+			addrdir >> 1, size, rc);
+		goto bail;
+	}
+
+	if (size == I2C_SMBUS_WORD_DATA && read) {
+		data->word = ((u16)local[1]) << 8;
+		data->word |= local[0];
+	}
+
  bail:
 	pmac_i2c_close(bus);
 	return rc;
@@ -146,20 +152,33 @@ static int i2c_powermac_master_xfer(	struct i2c_adapter *adap,
 	int			read;
 	int			addrdir;
 
+	if (num != 1) {
+		dev_err(&adap->dev,
+			"Multi-message I2C transactions not supported\n");
+		return -EOPNOTSUPP;
+	}
+
 	if (msgs->flags & I2C_M_TEN)
 		return -EINVAL;
 	read = (msgs->flags & I2C_M_RD) != 0;
 	addrdir = (msgs->addr << 1) | read;
-	if (msgs->flags & I2C_M_REV_DIR_ADDR)
-		addrdir ^= 1;
 
 	rc = pmac_i2c_open(bus, 0);
-	if (rc)
+	if (rc) {
+		dev_err(&adap->dev, "Failed to open I2C, err %d\n", rc);
 		return rc;
+	}
 	rc = pmac_i2c_setmode(bus, pmac_i2c_mode_std);
-	if (rc)
+	if (rc) {
+		dev_err(&adap->dev, "Failed to set I2C mode %d, err %d\n",
+			pmac_i2c_mode_std, rc);
 		goto bail;
+	}
 	rc = pmac_i2c_xfer(bus, addrdir, 0, 0, msgs->buf, msgs->len);
+	if (rc < 0)
+		dev_err(&adap->dev, "I2C %s 0x%02x failed, err %d\n",
+			addrdir & 1 ? "read from" : "write to", addrdir >> 1,
+			rc);
  bail:
 	pmac_i2c_close(bus);
 	return rc < 0 ? rc : 1;
@@ -183,19 +202,16 @@ static const struct i2c_algorithm i2c_powermac_algorithm = {
 static int __devexit i2c_powermac_remove(struct platform_device *dev)
 {
 	struct i2c_adapter	*adapter = platform_get_drvdata(dev);
-	struct pmac_i2c_bus	*bus = i2c_get_adapdata(adapter);
 	int			rc;
 
 	rc = i2c_del_adapter(adapter);
-	pmac_i2c_detach_adapter(bus, adapter);
-	i2c_set_adapdata(adapter, NULL);
 	/* We aren't that prepared to deal with this... */
 	if (rc)
 		printk(KERN_WARNING
 		       "i2c-powermac.c: Failed to remove bus %s !\n",
 		       adapter->name);
 	platform_set_drvdata(dev, NULL);
-	kfree(adapter);
+	memset(adapter, 0, sizeof(*adapter));
 
 	return 0;
 }
@@ -206,12 +222,12 @@ static int __devinit i2c_powermac_probe(struct platform_device *dev)
 	struct pmac_i2c_bus *bus = dev->dev.platform_data;
 	struct device_node *parent = NULL;
 	struct i2c_adapter *adapter;
-	char name[32];
 	const char *basename;
 	int rc;
 
 	if (bus == NULL)
 		return -EINVAL;
+	adapter = pmac_i2c_get_adapter(bus);
 
 	/* Ok, now we need to make up a name for the interface that will
 	 * match what we used to do in the past, that is basically the
@@ -237,29 +253,22 @@ static int __devinit i2c_powermac_probe(struct platform_device *dev)
 	default:
 		return -EINVAL;
 	}
-	snprintf(name, 32, "%s %d", basename, pmac_i2c_get_channel(bus));
+	snprintf(adapter->name, sizeof(adapter->name), "%s %d", basename,
+		 pmac_i2c_get_channel(bus));
 	of_node_put(parent);
 
-	adapter = kzalloc(sizeof(struct i2c_adapter), GFP_KERNEL);
-	if (adapter == NULL) {
-		printk(KERN_ERR "i2c-powermac: can't allocate inteface !\n");
-		return -ENOMEM;
-	}
 	platform_set_drvdata(dev, adapter);
-	strcpy(adapter->name, name);
 	adapter->algo = &i2c_powermac_algorithm;
 	i2c_set_adapdata(adapter, bus);
 	adapter->dev.parent = &dev->dev;
-	pmac_i2c_attach_adapter(bus, adapter);
 	rc = i2c_add_adapter(adapter);
 	if (rc) {
 		printk(KERN_ERR "i2c-powermac: Adapter %s registration "
-		       "failed\n", name);
-		i2c_set_adapdata(adapter, NULL);
-		pmac_i2c_detach_adapter(bus, adapter);
+		       "failed\n", adapter->name);
+		memset(adapter, 0, sizeof(*adapter));
 	}
 
-	printk(KERN_INFO "PowerMac i2c bus %s registered\n", name);
+	printk(KERN_INFO "PowerMac i2c bus %s registered\n", adapter->name);
 
 	if (!strncmp(basename, "uni-n", 5)) {
 		struct device_node *np;

drivers/i2c/busses/i2c-sis5595.c

@@ -142,7 +142,7 @@ static void sis5595_write(u8 reg, u8 data)
 	outb(data, sis5595_base + SMB_DAT);
 }
 
-static int sis5595_setup(struct pci_dev *SIS5595_dev)
+static int __devinit sis5595_setup(struct pci_dev *SIS5595_dev)
 {
 	u16 a;
 	u8 val;

drivers/i2c/busses/i2c-sis630.c

@@ -389,7 +389,7 @@ static u32 sis630_func(struct i2c_adapter *adapter)
 		I2C_FUNC_SMBUS_BLOCK_DATA;
 }
 
-static int sis630_setup(struct pci_dev *sis630_dev)
+static int __devinit sis630_setup(struct pci_dev *sis630_dev)
 {
 	unsigned char b;
 	struct pci_dev *dummy = NULL;

drivers/i2c/busses/i2c-stub.c

@@ -35,6 +35,10 @@ module_param_array(chip_addr, ushort, NULL, S_IRUGO);
 MODULE_PARM_DESC(chip_addr,
 		 "Chip addresses (up to 10, between 0x03 and 0x77)");
 
+static unsigned long functionality = ~0UL;
+module_param(functionality, ulong, S_IRUGO | S_IWUSR);
+MODULE_PARM_DESC(functionality, "Override functionality bitfield");
+
 struct stub_chip {
 	u8 pointer;
 	u16 words[256];		/* Byte operations use the LSB as per SMBus
@@ -48,7 +52,7 @@ static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags,
 	char read_write, u8 command, int size, union i2c_smbus_data * data)
 {
 	s32 ret;
-	int i;
+	int i, len;
 	struct stub_chip *chip = NULL;
 
 	/* Search for the right chip */
@@ -118,6 +122,29 @@ static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags,
 		ret = 0;
 		break;
 
+	case I2C_SMBUS_I2C_BLOCK_DATA:
+		len = data->block[0];
+		if (read_write == I2C_SMBUS_WRITE) {
+			for (i = 0; i < len; i++) {
+				chip->words[command + i] &= 0xff00;
+				chip->words[command + i] |= data->block[1 + i];
+			}
+			dev_dbg(&adap->dev, "i2c block data - addr 0x%02x, "
+					"wrote %d bytes at 0x%02x.\n",
+					addr, len, command);
+		} else {
+			for (i = 0; i < len; i++) {
+				data->block[1 + i] =
+					chip->words[command + i] & 0xff;
+			}
+			dev_dbg(&adap->dev, "i2c block data - addr 0x%02x, "
+					"read  %d bytes at 0x%02x.\n",
+					addr, len, command);
+		}
+
+		ret = 0;
+		break;
+
 	default:
 		dev_dbg(&adap->dev, "Unsupported I2C/SMBus command\n");
 		ret = -EOPNOTSUPP;
@@ -129,8 +156,9 @@ static s32 stub_xfer(struct i2c_adapter * adap, u16 addr, unsigned short flags,
 
 static u32 stub_func(struct i2c_adapter *adapter)
 {
-	return I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
-		I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA;
+	return (I2C_FUNC_SMBUS_QUICK | I2C_FUNC_SMBUS_BYTE |
+		I2C_FUNC_SMBUS_BYTE_DATA | I2C_FUNC_SMBUS_WORD_DATA |
+		I2C_FUNC_SMBUS_I2C_BLOCK) & functionality;
 }
 
 static const struct i2c_algorithm smbus_algorithm = {

drivers/i2c/busses/i2c-voodoo3.c

-/*
-    Copyright (c) 1998, 1999  Frodo Looijaard <frodol@dds.nl>,
-    Philip Edelbrock <phil@netroedge.com>,
-    Ralph Metzler <rjkm@thp.uni-koeln.de>, and
-    Mark D. Studebaker <mdsxyz123@yahoo.com>
-    
-    Based on code written by Ralph Metzler <rjkm@thp.uni-koeln.de> and
-    Simon Vogl
-
-    This program is free software; you can redistribute it and/or modify
-    it under the terms of the GNU General Public License as published by
-    the Free Software Foundation; either version 2 of the License, or
-    (at your option) any later version.
-
-    This program is distributed in the hope that it will be useful,
-    but WITHOUT ANY WARRANTY; without even the implied warranty of
-    MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
-    GNU General Public License for more details.
-
-    You should have received a copy of the GNU General Public License
-    along with this program; if not, write to the Free Software
-    Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA.
-*/
-
-/* This interfaces to the I2C bus of the Voodoo3 to gain access to
-    the BT869 and possibly other I2C devices. */
-
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
-#include <linux/pci.h>
-#include <linux/i2c.h>
-#include <linux/i2c-algo-bit.h>
-#include <asm/io.h>
-
-/* the only registers we use */
-#define REG		0x78
-#define REG2 		0x70
-
-/* bit locations in the register */
-#define DDC_ENAB	0x00040000
-#define DDC_SCL_OUT	0x00080000
-#define DDC_SDA_OUT	0x00100000
-#define DDC_SCL_IN	0x00200000
-#define DDC_SDA_IN	0x00400000
-#define I2C_ENAB	0x00800000
-#define I2C_SCL_OUT	0x01000000
-#define I2C_SDA_OUT	0x02000000
-#define I2C_SCL_IN	0x04000000
-#define I2C_SDA_IN	0x08000000
-
-/* initialization states */
-#define INIT2		0x2
-#define INIT3		0x4
-
-/* delays */
-#define CYCLE_DELAY	10
-#define TIMEOUT		(HZ / 2)
-
-
-static void __iomem *ioaddr;
-
-/* The voo GPIO registers don't have individual masks for each bit
-   so we always have to read before writing. */
-
-static void bit_vooi2c_setscl(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if (val)
-		r |= I2C_SCL_OUT;
-	else
-		r &= ~I2C_SCL_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-static void bit_vooi2c_setsda(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if (val)
-		r |= I2C_SDA_OUT;
-	else
-		r &= ~I2C_SDA_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-/* The GPIO pins are open drain, so the pins always remain outputs.
-   We rely on the i2c-algo-bit routines to set the pins high before
-   reading the input from other chips. */
-
-static int bit_vooi2c_getscl(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & I2C_SCL_IN));
-}
-
-static int bit_vooi2c_getsda(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & I2C_SDA_IN));
-}
-
-static void bit_vooddc_setscl(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if (val)
-		r |= DDC_SCL_OUT;
-	else
-		r &= ~DDC_SCL_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-static void bit_vooddc_setsda(void *data, int val)
-{
-	unsigned int r;
-	r = readl(ioaddr + REG);
-	if (val)
-		r |= DDC_SDA_OUT;
-	else
-		r &= ~DDC_SDA_OUT;
-	writel(r, ioaddr + REG);
-	readl(ioaddr + REG);	/* flush posted write */
-}
-
-static int bit_vooddc_getscl(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & DDC_SCL_IN));
-}
-
-static int bit_vooddc_getsda(void *data)
-{
-	return (0 != (readl(ioaddr + REG) & DDC_SDA_IN));
-}
-
-static int config_v3(struct pci_dev *dev)
-{
-	unsigned long cadr;
-
-	/* map Voodoo3 memory */
-	cadr = dev->resource[0].start;
-	cadr &= PCI_BASE_ADDRESS_MEM_MASK;
-	ioaddr = ioremap_nocache(cadr, 0x1000);
-	if (ioaddr) {
-		writel(0x8160, ioaddr + REG2);
-		writel(0xcffc0020, ioaddr + REG);
-		dev_info(&dev->dev, "Using Banshee/Voodoo3 I2C device at %p\n", ioaddr);
-		return 0;
-	}
-	return -ENODEV;
-}
-
-static struct i2c_algo_bit_data voo_i2c_bit_data = {
-	.setsda		= bit_vooi2c_setsda,
-	.setscl		= bit_vooi2c_setscl,
-	.getsda		= bit_vooi2c_getsda,
-	.getscl		= bit_vooi2c_getscl,
-	.udelay		= CYCLE_DELAY,
-	.timeout	= TIMEOUT
-};
-
-static struct i2c_adapter voodoo3_i2c_adapter = {
-	.owner		= THIS_MODULE,
-	.name		= "I2C Voodoo3/Banshee adapter",
-	.algo_data	= &voo_i2c_bit_data,
-};
-
-static struct i2c_algo_bit_data voo_ddc_bit_data = {
-	.setsda		= bit_vooddc_setsda,
-	.setscl		= bit_vooddc_setscl,
-	.getsda		= bit_vooddc_getsda,
-	.getscl		= bit_vooddc_getscl,
-	.udelay		= CYCLE_DELAY,
-	.timeout	= TIMEOUT
-};
-
-static struct i2c_adapter voodoo3_ddc_adapter = {
-	.owner		= THIS_MODULE,
-	.class		= I2C_CLASS_DDC, 
-	.name		= "DDC Voodoo3/Banshee adapter",
-	.algo_data	= &voo_ddc_bit_data,
-};
-
-static struct pci_device_id voodoo3_ids[] __devinitdata = {
-	{ PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_VOODOO3) },
-	{ PCI_DEVICE(PCI_VENDOR_ID_3DFX, PCI_DEVICE_ID_3DFX_BANSHEE) },
-	{ 0, }
-};
-
-MODULE_DEVICE_TABLE (pci, voodoo3_ids);
-
-static int __devinit voodoo3_probe(struct pci_dev *dev, const struct pci_device_id *id)
-{
-	int retval;
-
-	retval = config_v3(dev);
-	if (retval)
-		return retval;
-
-	/* set up the sysfs linkage to our parent device */
-	voodoo3_i2c_adapter.dev.parent = &dev->dev;
-	voodoo3_ddc_adapter.dev.parent = &dev->dev;
-
-	retval = i2c_bit_add_bus(&voodoo3_i2c_adapter);
-	if (retval)
-		return retval;
-	retval = i2c_bit_add_bus(&voodoo3_ddc_adapter);
-	if (retval)
-		i2c_del_adapter(&voodoo3_i2c_adapter);
-	return retval;
-}
-
-static void __devexit voodoo3_remove(struct pci_dev *dev)
-{
-	i2c_del_adapter(&voodoo3_i2c_adapter);
-	i2c_del_adapter(&voodoo3_ddc_adapter);
-	iounmap(ioaddr);
-}
-
-static struct pci_driver voodoo3_driver = {
-	.name		= "voodoo3_smbus",
-	.id_table	= voodoo3_ids,
-	.probe		= voodoo3_probe,
-	.remove		= __devexit_p(voodoo3_remove),
-};
-
-static int __init i2c_voodoo3_init(void)
-{
-	return pci_register_driver(&voodoo3_driver);
-}
-
-static void __exit i2c_voodoo3_exit(void)
-{
-	pci_unregister_driver(&voodoo3_driver);
-}
-
-
-MODULE_AUTHOR("Frodo Looijaard <frodol@dds.nl>, "
-		"Philip Edelbrock <phil@netroedge.com>, "
-		"Ralph Metzler <rjkm@thp.uni-koeln.de>, "
-		"and Mark D. Studebaker <mdsxyz123@yahoo.com>");
-MODULE_DESCRIPTION("Voodoo3 I2C/SMBus driver");
-MODULE_LICENSE("GPL");
-
-module_init(i2c_voodoo3_init);
-module_exit(i2c_voodoo3_exit);

drivers/i2c/chips/Kconfig

@@ -6,16 +6,6 @@
 
 menu "Miscellaneous I2C Chip support"
 
-config DS1682
-	tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
-	depends on EXPERIMENTAL
-	help
-	  If you say yes here you get support for Dallas Semiconductor
-	  DS1682 Total Elapsed Time Recorder.
-
-	  This driver can also be built as a module.  If so, the module
-	  will be called ds1682.
-
 config SENSORS_TSL2550
 	tristate "Taos TSL2550 ambient light sensor"
 	depends on EXPERIMENTAL

drivers/i2c/chips/Makefile

@@ -10,7 +10,6 @@
 # * I/O expander drivers go to drivers/gpio
 #
 
-obj-$(CONFIG_DS1682)		+= ds1682.o
 obj-$(CONFIG_SENSORS_TSL2550)	+= tsl2550.o
 
 ifeq ($(CONFIG_I2C_DEBUG_CHIP),y)

drivers/i2c/i2c-core.c

@@ -558,11 +558,9 @@ static void i2c_scan_static_board_info(struct i2c_adapter *adapter)
 	up_read(&__i2c_board_lock);
 }
 
-static int i2c_do_add_adapter(struct device_driver *d, void *data)
+static int i2c_do_add_adapter(struct i2c_driver *driver,
+			      struct i2c_adapter *adap)
 {
-	struct i2c_driver *driver = to_i2c_driver(d);
-	struct i2c_adapter *adap = data;
-
 	/* Detect supported devices on that bus, and instantiate them */
 	i2c_detect(adap, driver);
 
@@ -574,6 +572,11 @@ static int i2c_do_add_adapter(struct device_driver *d, void *data)
 	return 0;
 }
 
+static int __process_new_adapter(struct device_driver *d, void *data)
+{
+	return i2c_do_add_adapter(to_i2c_driver(d), data);
+}
+
 static int i2c_register_adapter(struct i2c_adapter *adap)
 {
 	int res = 0, dummy;
@@ -584,7 +587,7 @@ static int i2c_register_adapter(struct i2c_adapter *adap)
 		goto out_list;
 	}
 
-	mutex_init(&adap->bus_lock);
+	rt_mutex_init(&adap->bus_lock);
 
 	/* Set default timeout to 1 second if not already set */
 	if (adap->timeout == 0)
@@ -614,7 +617,7 @@ static int i2c_register_adapter(struct i2c_adapter *adap)
 	/* Notify drivers */
 	mutex_lock(&core_lock);
 	dummy = bus_for_each_drv(&i2c_bus_type, NULL, adap,
-				 i2c_do_add_adapter);
+				 __process_new_adapter);
 	mutex_unlock(&core_lock);
 
 	return 0;
@@ -715,10 +718,9 @@ int i2c_add_numbered_adapter(struct i2c_adapter *adap)
 }
 EXPORT_SYMBOL_GPL(i2c_add_numbered_adapter);
 
-static int i2c_do_del_adapter(struct device_driver *d, void *data)
+static int i2c_do_del_adapter(struct i2c_driver *driver,
+			      struct i2c_adapter *adapter)
 {
-	struct i2c_driver *driver = to_i2c_driver(d);
-	struct i2c_adapter *adapter = data;
 	struct i2c_client *client, *_n;
 	int res;
 
@@ -750,6 +752,11 @@ static int __unregister_client(struct device *dev, void *dummy)
 	return 0;
 }
 
+static int __process_removed_adapter(struct device_driver *d, void *data)
+{
+	return i2c_do_del_adapter(to_i2c_driver(d), data);
+}
+
 /**
  * i2c_del_adapter - unregister I2C adapter
  * @adap: the adapter being unregistered
@@ -777,7 +784,7 @@ int i2c_del_adapter(struct i2c_adapter *adap)
 	/* Tell drivers about this removal */
 	mutex_lock(&core_lock);
 	res = bus_for_each_drv(&i2c_bus_type, NULL, adap,
-			       i2c_do_del_adapter);
+			       __process_removed_adapter);
 	mutex_unlock(&core_lock);
 	if (res)
 		return res;
@@ -826,22 +833,11 @@ EXPORT_SYMBOL(i2c_del_adapter);
 
 /* ------------------------------------------------------------------------- */
 
-static int __attach_adapter(struct device *dev, void *data)
+static int __process_new_driver(struct device *dev, void *data)
 {
-	struct i2c_adapter *adapter;
-	struct i2c_driver *driver = data;
-
 	if (dev->type != &i2c_adapter_type)
 		return 0;
-	adapter = to_i2c_adapter(dev);
-
-	i2c_detect(adapter, driver);
-
-	/* Legacy drivers scan i2c busses directly */
-	if (driver->attach_adapter)
-		driver->attach_adapter(adapter);
-
-	return 0;
+	return i2c_do_add_adapter(data, to_i2c_adapter(dev));
 }
 
 /*
@@ -873,40 +869,18 @@ int i2c_register_driver(struct module *owner, struct i2c_driver *driver)
 	INIT_LIST_HEAD(&driver->clients);
 	/* Walk the adapters that are already present */
 	mutex_lock(&core_lock);
-	bus_for_each_dev(&i2c_bus_type, NULL, driver, __attach_adapter);
+	bus_for_each_dev(&i2c_bus_type, NULL, driver, __process_new_driver);
 	mutex_unlock(&core_lock);
 
 	return 0;
 }
 EXPORT_SYMBOL(i2c_register_driver);
 
-static int __detach_adapter(struct device *dev, void *data)
+static int __process_removed_driver(struct device *dev, void *data)
 {
-	struct i2c_adapter *adapter;
-	struct i2c_driver *driver = data;
-	struct i2c_client *client, *_n;
-
 	if (dev->type != &i2c_adapter_type)
 		return 0;
-	adapter = to_i2c_adapter(dev);
-
-	/* Remove the devices we created ourselves as the result of hardware
-	 * probing (using a driver's detect method) */
-	list_for_each_entry_safe(client, _n, &driver->clients, detected) {
-		dev_dbg(&adapter->dev, "Removing %s at 0x%x\n",
-			client->name, client->addr);
-		list_del(&client->detected);
-		i2c_unregister_device(client);
-	}
-
-	if (driver->detach_adapter) {
-		if (driver->detach_adapter(adapter))
-			dev_err(&adapter->dev,
-				"detach_adapter failed for driver [%s]\n",
-				driver->driver.name);
-	}
-
-	return 0;
+	return i2c_do_del_adapter(data, to_i2c_adapter(dev));
 }
 
 /**
@@ -917,7 +891,7 @@ static int __detach_adapter(struct device *dev, void *data)
 void i2c_del_driver(struct i2c_driver *driver)
 {
 	mutex_lock(&core_lock);
-	bus_for_each_dev(&i2c_bus_type, NULL, driver, __detach_adapter);
+	bus_for_each_dev(&i2c_bus_type, NULL, driver, __process_removed_driver);
 	mutex_unlock(&core_lock);
 
 	driver_unregister(&driver->driver);
@@ -1092,12 +1066,12 @@ int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
 #endif
 
 		if (in_atomic() || irqs_disabled()) {
-			ret = mutex_trylock(&adap->bus_lock);
+			ret = rt_mutex_trylock(&adap->bus_lock);
 			if (!ret)
 				/* I2C activity is ongoing. */
 				return -EAGAIN;
 		} else {
-			mutex_lock_nested(&adap->bus_lock, adap->level);
+			rt_mutex_lock(&adap->bus_lock);
 		}
 
 		/* Retry automatically on arbitration loss */
@@ -1109,7 +1083,7 @@ int i2c_transfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
 			if (time_after(jiffies, orig_jiffies + adap->timeout))
 				break;
 		}
-		mutex_unlock(&adap->bus_lock);
+		rt_mutex_unlock(&adap->bus_lock);
 
 		return ret;
 	} else {
@@ -1180,7 +1154,7 @@ EXPORT_SYMBOL(i2c_master_recv);
  * ----------------------------------------------------
  */
 
-static int i2c_detect_address(struct i2c_client *temp_client, int kind,
+static int i2c_detect_address(struct i2c_client *temp_client,
 			      struct i2c_driver *driver)
 {
 	struct i2c_board_info info;
@@ -1199,22 +1173,18 @@ static int i2c_detect_address(struct i2c_client *temp_client, int kind,
 	if (i2c_check_addr(adapter, addr))
 		return 0;
 
-	/* Make sure there is something at this address, unless forced */
-	if (kind < 0) {
-		if (i2c_smbus_xfer(adapter, addr, 0, 0, 0,
-				   I2C_SMBUS_QUICK, NULL) < 0)
-			return 0;
+	/* Make sure there is something at this address */
+	if (i2c_smbus_xfer(adapter, addr, 0, 0, 0, I2C_SMBUS_QUICK, NULL) < 0)
+		return 0;
 
-		/* prevent 24RF08 corruption */
-		if ((addr & ~0x0f) == 0x50)
-			i2c_smbus_xfer(adapter, addr, 0, 0, 0,
-				       I2C_SMBUS_QUICK, NULL);
-	}
+	/* Prevent 24RF08 corruption */
+	if ((addr & ~0x0f) == 0x50)
+		i2c_smbus_xfer(adapter, addr, 0, 0, 0, I2C_SMBUS_QUICK, NULL);
 
 	/* Finally call the custom detection function */
 	memset(&info, 0, sizeof(struct i2c_board_info));
 	info.addr = addr;
-	err = driver->detect(temp_client, kind, &info);
+	err = driver->detect(temp_client, -1, &info);
 	if (err) {
 		/* -ENODEV is returned if the detection fails. We catch it
 		   here as this isn't an error. */
@@ -1259,40 +1229,13 @@ static int i2c_detect(struct i2c_adapter *adapter, struct i2c_driver *driver)
 		return -ENOMEM;
 	temp_client->adapter = adapter;
 
-	/* Force entries are done first, and are not affected by ignore
-	   entries */
-	if (address_data->forces) {
-		const unsigned short * const *forces = address_data->forces;
-		int kind;
-
-		for (kind = 0; forces[kind]; kind++) {
-			for (i = 0; forces[kind][i] != I2C_CLIENT_END;
-			     i += 2) {
-				if (forces[kind][i] == adap_id
-				 || forces[kind][i] == ANY_I2C_BUS) {
-					dev_dbg(&adapter->dev, "found force "
-						"parameter for adapter %d, "
-						"addr 0x%02x, kind %d\n",
-						adap_id, forces[kind][i + 1],
-						kind);
-					temp_client->addr = forces[kind][i + 1];
-					err = i2c_detect_address(temp_client,
-						kind, driver);
-					if (err)
-						goto exit_free;
-				}
-			}
-		}
-	}
-
 	/* Stop here if the classes do not match */
 	if (!(adapter->class & driver->class))
 		goto exit_free;
 
 	/* Stop here if we can't use SMBUS_QUICK */
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_QUICK)) {
-		if (address_data->probe[0] == I2C_CLIENT_END
-		 && address_data->normal_i2c[0] == I2C_CLIENT_END)
+		if (address_data->normal_i2c[0] == I2C_CLIENT_END)
 			goto exit_free;
 
 		dev_warn(&adapter->dev, "SMBus Quick command not supported, "
@@ -1301,48 +1244,12 @@ static int i2c_detect(struct i2c_adapter *adapter, struct i2c_driver *driver)
 		goto exit_free;
 	}
 
-	/* Probe entries are done second, and are not affected by ignore
-	   entries either */
-	for (i = 0; address_data->probe[i] != I2C_CLIENT_END; i += 2) {
-		if (address_data->probe[i] == adap_id
-		 || address_data->probe[i] == ANY_I2C_BUS) {
-			dev_dbg(&adapter->dev, "found probe parameter for "
-				"adapter %d, addr 0x%02x\n", adap_id,
-				address_data->probe[i + 1]);
-			temp_client->addr = address_data->probe[i + 1];
-			err = i2c_detect_address(temp_client, -1, driver);
-			if (err)
-				goto exit_free;
-		}
-	}
-
-	/* Normal entries are done last, unless shadowed by an ignore entry */
 	for (i = 0; address_data->normal_i2c[i] != I2C_CLIENT_END; i += 1) {
-		int j, ignore;
-
-		ignore = 0;
-		for (j = 0; address_data->ignore[j] != I2C_CLIENT_END;
-		     j += 2) {
-			if ((address_data->ignore[j] == adap_id ||
-			     address_data->ignore[j] == ANY_I2C_BUS)
-			 && address_data->ignore[j + 1]
-			    == address_data->normal_i2c[i]) {
-				dev_dbg(&adapter->dev, "found ignore "
-					"parameter for adapter %d, "
-					"addr 0x%02x\n", adap_id,
-					address_data->ignore[j + 1]);
-				ignore = 1;
-				break;
-			}
-		}
-		if (ignore)
-			continue;
-
 		dev_dbg(&adapter->dev, "found normal entry for adapter %d, "
 			"addr 0x%02x\n", adap_id,
 			address_data->normal_i2c[i]);
 		temp_client->addr = address_data->normal_i2c[i];
-		err = i2c_detect_address(temp_client, -1, driver);
+		err = i2c_detect_address(temp_client, driver);
 		if (err)
 			goto exit_free;
 	}
@@ -1913,7 +1820,7 @@ s32 i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr, unsigned short flags,
 	flags &= I2C_M_TEN | I2C_CLIENT_PEC;
 
 	if (adapter->algo->smbus_xfer) {
-		mutex_lock(&adapter->bus_lock);
+		rt_mutex_lock(&adapter->bus_lock);
 
 		/* Retry automatically on arbitration loss */
 		orig_jiffies = jiffies;
@@ -1927,7 +1834,7 @@ s32 i2c_smbus_xfer(struct i2c_adapter *adapter, u16 addr, unsigned short flags,
 				       orig_jiffies + adapter->timeout))
 				break;
 		}
-		mutex_unlock(&adapter->bus_lock);
+		rt_mutex_unlock(&adapter->bus_lock);
 	} else
 		res = i2c_smbus_xfer_emulated(adapter,addr,flags,read_write,
 					      command, protocol, data);

drivers/i2c/i2c-dev.c

@@ -34,7 +34,6 @@
 #include <linux/list.h>
 #include <linux/i2c.h>
 #include <linux/i2c-dev.h>
-#include <linux/smp_lock.h>
 #include <linux/jiffies.h>
 #include <asm/uaccess.h>
 
@@ -445,20 +444,14 @@ static int i2cdev_open(struct inode *inode, struct file *file)
 	struct i2c_client *client;
 	struct i2c_adapter *adap;
 	struct i2c_dev *i2c_dev;
-	int ret = 0;
 
-	lock_kernel();
 	i2c_dev = i2c_dev_get_by_minor(minor);
-	if (!i2c_dev) {
-		ret = -ENODEV;
-		goto out;
-	}
+	if (!i2c_dev)
+		return -ENODEV;
 
 	adap = i2c_get_adapter(i2c_dev->adap->nr);
-	if (!adap) {
-		ret = -ENODEV;
-		goto out;
-	}
+	if (!adap)
+		return -ENODEV;
 
 	/* This creates an anonymous i2c_client, which may later be
 	 * pointed to some address using I2C_SLAVE or I2C_SLAVE_FORCE.
@@ -470,8 +463,7 @@ static int i2cdev_open(struct inode *inode, struct file *file)
 	client = kzalloc(sizeof(*client), GFP_KERNEL);
 	if (!client) {
 		i2c_put_adapter(adap);
-		ret = -ENOMEM;
-		goto out;
+		return -ENOMEM;
 	}
 	snprintf(client->name, I2C_NAME_SIZE, "i2c-dev %d", adap->nr);
 	client->driver = &i2cdev_driver;
@@ -479,9 +471,7 @@ static int i2cdev_open(struct inode *inode, struct file *file)
 	client->adapter = adap;
 	file->private_data = client;
 
-out:
-	unlock_kernel();
-	return ret;
+	return 0;
 }
 
 static int i2cdev_release(struct inode *inode, struct file *file)

drivers/misc/Kconfig

@@ -246,6 +246,16 @@ config EP93XX_PWM
 	  To compile this driver as a module, choose M here: the module will
 	  be called ep93xx_pwm.
 
+config DS1682
+	tristate "Dallas DS1682 Total Elapsed Time Recorder with Alarm"
+	depends on I2C && EXPERIMENTAL
+	help
+	  If you say yes here you get support for Dallas Semiconductor
+	  DS1682 Total Elapsed Time Recorder.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called ds1682.
+
 source "drivers/misc/c2port/Kconfig"
 source "drivers/misc/eeprom/Kconfig"
 source "drivers/misc/cb710/Kconfig"

drivers/misc/Makefile

@@ -20,6 +20,7 @@ obj-$(CONFIG_SGI_GRU)		+= sgi-gru/
 obj-$(CONFIG_HP_ILO)		+= hpilo.o
 obj-$(CONFIG_ISL29003)		+= isl29003.o
 obj-$(CONFIG_EP93XX_PWM)	+= ep93xx_pwm.o
+obj-$(CONFIG_DS1682)		+= ds1682.o
 obj-$(CONFIG_C2PORT)		+= c2port/
 obj-$(CONFIG_IWMC3200TOP)      += iwmc3200top/
 obj-y				+= eeprom/

drivers/misc/ics932s401.c

@@ -417,32 +417,25 @@ static int ics932s401_detect(struct i2c_client *client, int kind,
 			  struct i2c_board_info *info)
 {
 	struct i2c_adapter *adapter = client->adapter;
+	int vendor, device, revision;
 
 	if (!i2c_check_functionality(adapter, I2C_FUNC_SMBUS_BYTE_DATA))
 		return -ENODEV;
 
-	if (kind <= 0) {
-		int vendor, device, revision;
-
-		vendor = i2c_smbus_read_word_data(client,
-						  ICS932S401_REG_VENDOR_REV);
-		vendor >>= 8;
-		revision = vendor >> ICS932S401_REV_SHIFT;
-		vendor &= ICS932S401_VENDOR_MASK;
-		if (vendor != ICS932S401_VENDOR)
-			return -ENODEV;
-
-		device = i2c_smbus_read_word_data(client,
-						  ICS932S401_REG_DEVICE);
-		device >>= 8;
-		if (device != ICS932S401_DEVICE)
-			return -ENODEV;
-
-		if (revision != ICS932S401_REV)
-			dev_info(&adapter->dev, "Unknown revision %d\n",
-				 revision);
-	} else
-		dev_dbg(&adapter->dev, "detection forced\n");
+	vendor = i2c_smbus_read_word_data(client, ICS932S401_REG_VENDOR_REV);
+	vendor >>= 8;
+	revision = vendor >> ICS932S401_REV_SHIFT;
+	vendor &= ICS932S401_VENDOR_MASK;
+	if (vendor != ICS932S401_VENDOR)
+		return -ENODEV;
+
+	device = i2c_smbus_read_word_data(client, ICS932S401_REG_DEVICE);
+	device >>= 8;
+	if (device != ICS932S401_DEVICE)
+		return -ENODEV;
+
+	if (revision != ICS932S401_REV)
+		dev_info(&adapter->dev, "Unknown revision %d\n", revision);
 
 	strlcpy(info->type, "ics932s401", I2C_NAME_SIZE);
 

include/linux/i2c.h

@@ -110,7 +110,7 @@ extern s32 i2c_smbus_write_i2c_block_data(struct i2c_client *client,
  * @driver: Device driver model driver
  * @id_table: List of I2C devices supported by this driver
  * @detect: Callback for device detection
- * @address_data: The I2C addresses to probe, ignore or force (for detect)
+ * @address_data: The I2C addresses to probe (for detect)
  * @clients: List of detected clients we created (for i2c-core use only)
  *
  * The driver.owner field should be set to the module owner of this driver.
@@ -338,8 +338,7 @@ struct i2c_adapter {
 	void *algo_data;
 
 	/* data fields that are valid for all devices	*/
-	u8 level; 			/* nesting level for lockdep */
-	struct mutex bus_lock;
+	struct rt_mutex bus_lock;
 
 	int timeout;			/* in jiffies */
 	int retries;
@@ -367,7 +366,7 @@ static inline void i2c_set_adapdata(struct i2c_adapter *dev, void *data)
  */
 static inline void i2c_lock_adapter(struct i2c_adapter *adapter)
 {
-	mutex_lock(&adapter->bus_lock);
+	rt_mutex_lock(&adapter->bus_lock);
 }
 
 /**
@@ -376,7 +375,7 @@ static inline void i2c_lock_adapter(struct i2c_adapter *adapter)
  */
 static inline void i2c_unlock_adapter(struct i2c_adapter *adapter)
 {
-	mutex_unlock(&adapter->bus_lock);
+	rt_mutex_unlock(&adapter->bus_lock);
 }
 
 /*flags for the client struct: */
@@ -398,9 +397,6 @@ static inline void i2c_unlock_adapter(struct i2c_adapter *adapter)
  */
 struct i2c_client_address_data {
 	const unsigned short *normal_i2c;
-	const unsigned short *probe;
-	const unsigned short *ignore;
-	const unsigned short * const *forces;
 };
 
 /* Internal numbers to terminate lists */
@@ -614,134 +610,48 @@ union i2c_smbus_data {
   module_param_array(var, short, &var##_num, 0); \
   MODULE_PARM_DESC(var, desc)
 
-#define I2C_CLIENT_MODULE_PARM_FORCE(name)				\
-I2C_CLIENT_MODULE_PARM(force_##name,					\
-		       "List of adapter,address pairs which are "	\
-		       "unquestionably assumed to contain a `"		\
-		       # name "' chip")
-
-
 #define I2C_CLIENT_INSMOD_COMMON					\
-I2C_CLIENT_MODULE_PARM(probe, "List of adapter,address pairs to scan "	\
-		       "additionally");					\
-I2C_CLIENT_MODULE_PARM(ignore, "List of adapter,address pairs not to "	\
-		       "scan");						\
 static const struct i2c_client_address_data addr_data = {		\
 	.normal_i2c	= normal_i2c,					\
-	.probe		= probe,					\
-	.ignore		= ignore,					\
-	.forces		= forces,					\
 }
 
-#define I2C_CLIENT_FORCE_TEXT \
-	"List of adapter,address pairs to boldly assume to be present"
-
 /* These are the ones you want to use in your own drivers. Pick the one
    which matches the number of devices the driver differenciates between. */
 #define I2C_CLIENT_INSMOD						\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-static const unsigned short * const forces[] = { force, NULL };		\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_1(chip1)					\
 enum chips { any_chip, chip1 };						\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-static const unsigned short * const forces[] =	{ force,		\
-	force_##chip1, NULL };						\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_2(chip1, chip2)				\
 enum chips { any_chip, chip1, chip2 };					\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-static const unsigned short * const forces[] =	{ force,		\
-	force_##chip1, force_##chip2, NULL };				\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_3(chip1, chip2, chip3)			\
 enum chips { any_chip, chip1, chip2, chip3 };				\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-static const unsigned short * const forces[] =	{ force,		\
-	force_##chip1, force_##chip2, force_##chip3, NULL };		\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_4(chip1, chip2, chip3, chip4)			\
 enum chips { any_chip, chip1, chip2, chip3, chip4 };			\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip4);					\
-static const unsigned short * const forces[] =	{ force,		\
-	force_##chip1, force_##chip2, force_##chip3,			\
-	force_##chip4, NULL};						\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_5(chip1, chip2, chip3, chip4, chip5)		\
 enum chips { any_chip, chip1, chip2, chip3, chip4, chip5 };		\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip4);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip5);					\
-static const unsigned short * const forces[] = { force,			\
-	force_##chip1, force_##chip2, force_##chip3,			\
-	force_##chip4, force_##chip5, NULL };				\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_6(chip1, chip2, chip3, chip4, chip5, chip6)	\
 enum chips { any_chip, chip1, chip2, chip3, chip4, chip5, chip6 };	\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip4);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip5);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip6);					\
-static const unsigned short * const forces[] = { force,			\
-	force_##chip1, force_##chip2, force_##chip3,			\
-	force_##chip4, force_##chip5, force_##chip6, NULL };		\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_7(chip1, chip2, chip3, chip4, chip5, chip6, chip7) \
 enum chips { any_chip, chip1, chip2, chip3, chip4, chip5, chip6,	\
 	     chip7 };							\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip4);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip5);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip6);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip7);					\
-static const unsigned short * const forces[] = { force,			\
-	force_##chip1, force_##chip2, force_##chip3,			\
-	force_##chip4, force_##chip5, force_##chip6,			\
-	force_##chip7, NULL };						\
 I2C_CLIENT_INSMOD_COMMON
 
 #define I2C_CLIENT_INSMOD_8(chip1, chip2, chip3, chip4, chip5, chip6, chip7, chip8) \
 enum chips { any_chip, chip1, chip2, chip3, chip4, chip5, chip6,	\
 	     chip7, chip8 };						\
-I2C_CLIENT_MODULE_PARM(force, I2C_CLIENT_FORCE_TEXT);			\
-I2C_CLIENT_MODULE_PARM_FORCE(chip1);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip2);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip3);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip4);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip5);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip6);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip7);					\
-I2C_CLIENT_MODULE_PARM_FORCE(chip8);					\
-static const unsigned short * const forces[] = { force,			\
-	force_##chip1, force_##chip2, force_##chip3,			\
-	force_##chip4, force_##chip5, force_##chip6,			\
-	force_##chip7, force_##chip8, NULL };				\
 I2C_CLIENT_INSMOD_COMMON
 #endif /* __KERNEL__ */
 #endif /* _LINUX_I2C_H */