Commit 415e0fec authored by Manuel Lauss's avatar Manuel Lauss Committed by Ralf Baechle

MIPS: Alchemy: db1x00: use clk framework

Make use of the clk framework to set up and enable all PSC clocks.
Signed-off-by: default avatarManuel Lauss <manuel.lauss@gmail.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/7469/Signed-off-by: default avatarRalf Baechle <ralf@linux-mips.org>
parent 8e211705
......@@ -18,6 +18,7 @@
* Foundation, Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
*/
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
......@@ -129,7 +130,6 @@ static int __init db1200_detect_board(void)
int __init db1200_board_setup(void)
{
unsigned long freq0, clksrc, div, pfc;
unsigned short whoami;
if (db1200_detect_board())
......@@ -149,30 +149,6 @@ int __init db1200_board_setup(void)
" Board-ID %d Daughtercard ID %d\n", get_system_type(),
(whoami >> 4) & 0xf, (whoami >> 8) & 0xf, whoami & 0xf);
/* SMBus/SPI on PSC0, Audio on PSC1 */
pfc = alchemy_rdsys(AU1000_SYS_PINFUNC);
pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
/* Clock configurations: PSC0: ~50MHz via Clkgen0, derived from
* CPU clock; all other clock generators off/unused.
*/
div = (get_au1x00_speed() + 25000000) / 50000000;
if (div & 1)
div++;
div = ((div >> 1) - 1) & 0xff;
freq0 = div << SYS_FC_FRDIV0_BIT;
alchemy_wrsys(freq0, AU1000_SYS_FREQCTRL0);
freq0 |= SYS_FC_FE0; /* enable F0 */
alchemy_wrsys(freq0, AU1000_SYS_FREQCTRL0);
/* psc0_intclk comes 1:1 from F0 */
clksrc = SYS_CS_MUX_FQ0 << SYS_CS_ME0_BIT;
alchemy_wrsys(clksrc, AU1000_SYS_CLKSRC);
return 0;
}
......@@ -843,6 +819,7 @@ int __init db1200_dev_setup(void)
unsigned long pfc;
unsigned short sw;
int swapped, bid;
struct clk *c;
bid = BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI));
if ((bid == BCSR_WHOAMI_PB1200_DDR1) ||
......@@ -855,6 +832,24 @@ int __init db1200_dev_setup(void)
irq_set_irq_type(AU1200_GPIO7_INT, IRQ_TYPE_LEVEL_LOW);
bcsr_init_irq(DB1200_INT_BEGIN, DB1200_INT_END, AU1200_GPIO7_INT);
/* SMBus/SPI on PSC0, Audio on PSC1 */
pfc = alchemy_rdsys(AU1000_SYS_PINFUNC);
pfc &= ~(SYS_PINFUNC_P0A | SYS_PINFUNC_P0B);
pfc &= ~(SYS_PINFUNC_P1A | SYS_PINFUNC_P1B | SYS_PINFUNC_FS3);
pfc |= SYS_PINFUNC_P1C; /* SPI is configured later */
alchemy_wrsys(pfc, AU1000_SYS_PINFUNC);
/* get 50MHz for I2C driver on PSC0 */
c = clk_get(NULL, "psc0_intclk");
if (!IS_ERR(c)) {
pfc = clk_round_rate(c, 50000000);
if ((pfc < 1) || (abs(50000000 - pfc) > 2500000))
pr_warn("DB1200: cant get I2C close to 50MHz\n");
else
clk_set_rate(c, pfc);
clk_put(c);
}
/* insert/eject pairs: one of both is always screaming. To avoid
* issues they must not be automatically enabled when initially
* requested.
......@@ -927,6 +922,11 @@ int __init db1200_dev_setup(void)
}
/* Audio PSC clock is supplied externally. (FIXME: platdata!!) */
c = clk_get(NULL, "psc1_intclk");
if (!IS_ERR(c)) {
clk_prepare_enable(c);
clk_put(c);
}
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
......
......@@ -4,6 +4,7 @@
* (c) 2009 Manuel Lauss <manuel.lauss@googlemail.com>
*/
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/gpio.h>
#include <linux/gpio_keys.h>
......@@ -731,6 +732,7 @@ static struct platform_device *db1300_dev[] __initdata = {
int __init db1300_dev_setup(void)
{
int swapped, cpldirq;
struct clk *c;
/* setup CPLD IRQ muxer */
cpldirq = au1300_gpio_to_irq(AU1300_PIN_EXTCLK1);
......@@ -761,6 +763,11 @@ int __init db1300_dev_setup(void)
(void __iomem *)KSEG1ADDR(AU1300_PSC2_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
/* I2C uses internal 48MHz EXTCLK1 */
c = clk_get(NULL, "psc3_intclk");
if (!IS_ERR(c)) {
clk_prepare_enable(c);
clk_put(c);
}
__raw_writel(PSC_SEL_CLK_INTCLK,
(void __iomem *)KSEG1ADDR(AU1300_PSC3_PHYS_ADDR) + PSC_SEL_OFFSET);
wmb();
......
......@@ -4,6 +4,7 @@
* (c) 2011 Manuel Lauss <manuel.lauss@googlemail.com>
*/
#include <linux/clk.h>
#include <linux/dma-mapping.h>
#include <linux/gpio.h>
#include <linux/i2c.h>
......@@ -574,6 +575,7 @@ static void __init pb1550_devices(void)
int __init db1550_dev_setup(void)
{
int swapped, id;
struct clk *c;
id = (BCSR_WHOAMI_BOARD(bcsr_read(BCSR_WHOAMI)) != BCSR_WHOAMI_DB1550);
......@@ -582,6 +584,17 @@ int __init db1550_dev_setup(void)
spi_register_board_info(db1550_spi_devs,
ARRAY_SIZE(db1550_i2c_devs));
c = clk_get(NULL, "psc0_intclk");
if (!IS_ERR(c)) {
clk_prepare_enable(c);
clk_put(c);
}
c = clk_get(NULL, "psc2_intclk");
if (!IS_ERR(c)) {
clk_prepare_enable(c);
clk_put(c);
}
/* Audio PSC clock is supplied by codecs (PSC1, 3) FIXME: platdata!! */
__raw_writel(PSC_SEL_CLK_SERCLK,
(void __iomem *)KSEG1ADDR(AU1550_PSC1_PHYS_ADDR) + PSC_SEL_OFFSET);
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment