Merge tag 'regulator-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator

Pull regulator updates from Mark Brown:
 "This has been a fairly quiet release for the regulator API, a few new
  drivers and a small API update:

   - Support for specifying an initial load as part of requesting
     regulators through the bulk API

   - Support for Maxim MAX597x, Qualcomm PM8074, PM8909 and Realtek
     RT5120 devices"

* tag 'regulator-v5.20' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (35 commits)
  regulator: core: Allow drivers to define their init data as const
  regulator: core: Allow specifying an initial load w/ the bulk API
  regulator: mt6380: Fix unused array warning
  regulator: Add missing type for 'regulator-microvolt-offset'
  regulator: core: Fix off-on-delay-us for always-on/boot-on regulators
  regulator: of: Fix refcount leak bug in of_get_regulation_constraints()
  regulator: pwm: Update Lee Jones' email address
  regulator: max597x: Don't return uninitialized variable in .probe
  regulator: qcom,spmi-regulator: add PMP8074 PMIC
  regulator: qcom,spmi-regulator: Convert to dtschema
  regulator: qcom_spmi: add support for PMP8074 regulators
  regulator: qcom_spmi: add support for HT_P600
  regulator: qcom_spmi: add support for HT_P150
  regulator: max597x: Remove unused including <linux/version.h>
  regulator: Fix MFD_MAX597X dependency
  regulator: Fix parameter declaration and spelling mistake.
  regulator: max597x: Add support for max597x regulator
  regulator: scmi: Add missing of_node_get()
  regulator: qcom_smd: Add PM8909 RPM regulators
  regulator: dt-bindings: qcom,smd-rpm: Add PM8909
  ...

Documentation/devicetree/bindings/regulator/mps,mp5416.yaml

@@ -15,6 +15,7 @@ properties:
   compatible:
     enum:
       - mps,mp5416
+      - mps,mp5496
 
   reg:
     maxItems: 1

Documentation/devicetree/bindings/regulator/pwm-regulator.txt

-Bindings for the Generic PWM Regulator
-======================================
-
-Currently supports 2 modes of operation:
-
-Voltage Table:		When in this mode, a voltage table (See below) of
-			predefined voltage <=> duty-cycle values must be
-			provided via DT. Limitations are that the regulator can
-			only operate at the voltages supplied in the table.
-			Intermediary duty-cycle values which would normally
-			allow finer grained voltage selection are ignored and
-			rendered useless.  Although more control is given to
-			the user if the assumptions made in continuous-voltage
-			mode do not reign true.
-
-Continuous Voltage:	This mode uses the regulator's maximum and minimum
-			supplied voltages specified in the
-			regulator-{min,max}-microvolt properties to calculate
-			appropriate duty-cycle values.  This allows for a much
-			more fine grained solution when compared with
-			voltage-table mode above.  This solution does make an
-			assumption that a %50 duty-cycle value will cause the
-			regulator voltage to run at half way between the
-			supplied max_uV and min_uV values.
-
-Required properties:
---------------------
-- compatible:		Should be "pwm-regulator"
-
-- pwms:			PWM specification (See: ../pwm/pwm.txt)
-
-Only required for Voltage Table Mode:
-- voltage-table: 	Voltage and Duty-Cycle table consisting of 2 cells
-			    First cell is voltage in microvolts (uV)
-			    Second cell is duty-cycle in percent (%)
-
-Optional properties for Continuous mode:
-- pwm-dutycycle-unit:	Integer value encoding the duty cycle unit. If not
-			defined, <100> is assumed, meaning that
-			pwm-dutycycle-range contains values expressed in
-			percent.
-
-- pwm-dutycycle-range:	Should contain 2 entries. The first entry is encoding
-			the dutycycle for regulator-min-microvolt and the
-			second one the dutycycle for regulator-max-microvolt.
-			Duty cycle values are expressed in pwm-dutycycle-unit.
-			If not defined, <0 100> is assumed.
-
-NB: To be clear, if voltage-table is provided, then the device will be used
-in Voltage Table Mode.  If no voltage-table is provided, then the device will
-be used in Continuous Voltage Mode.
-
-Optional properties:
---------------------
-- enable-gpios:		GPIO to use to enable/disable the regulator
-
-Any property defined as part of the core regulator binding can also be used.
-(See: ../regulator/regulator.txt)
-
-Continuous Voltage With Enable GPIO Example:
-	pwm_regulator {
-		compatible = "pwm-regulator";
-		pwms = <&pwm1 0 8448 0>;
-		enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
-		regulator-min-microvolt = <1016000>;
-		regulator-max-microvolt = <1114000>;
-		regulator-name = "vdd_logic";
-		/* unit == per-mille */
-		pwm-dutycycle-unit = <1000>;
-		/*
-		 * Inverted PWM logic, and the duty cycle range is limited
-		 * to 30%-70%.
-		 */
-		pwm-dutycycle-range = <700 300>; /* */
-	};
-
-Voltage Table Example:
-	pwm_regulator {
-		compatible = "pwm-regulator";
-		pwms = <&pwm1 0 8448 0>;
-		regulator-min-microvolt = <1016000>;
-		regulator-max-microvolt = <1114000>;
-		regulator-name = "vdd_logic";
-
-			      /* Voltage Duty-Cycle */
-		voltage-table = <1114000 0>,
-				<1095000 10>,
-				<1076000 20>,
-				<1056000 30>,
-				<1036000 40>,
-				<1016000 50>;
-	};

Documentation/devicetree/bindings/regulator/pwm-regulator.yaml

+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/pwm-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Bindings for the Generic PWM Regulator
+
+maintainers:
+  - Brian Norris <briannorris@chromium.org>
+  - Lee Jones <lee@kernel.org>
+  - Alexandre Courbot <acourbot@nvidia.com>
+
+description: |
+  Currently supports 2 modes of operation:
+
+  Voltage Table:
+    When in this mode, a voltage table (See below) of predefined voltage <=>
+    duty-cycle values must be provided via DT. Limitations are that the
+    regulator can only operate at the voltages supplied in the table.
+    Intermediary duty-cycle values which would normally allow finer grained
+    voltage selection are ignored and rendered useless.  Although more control
+    is given to the user if the assumptions made in continuous-voltage mode do
+    not reign true.
+
+  Continuous Voltage:
+    This mode uses the regulator's maximum and minimum supplied voltages
+    specified in the regulator-{min,max}-microvolt properties to calculate
+    appropriate duty-cycle values.  This allows for a much more fine grained
+    solution when compared with voltage-table mode above.  This solution does
+    make an assumption that a %50 duty-cycle value will cause the regulator
+    voltage to run at half way between the supplied max_uV and min_uV values.
+
+  If voltage-table is provided, then the device will be used in Voltage Table
+  Mode.  If no voltage-table is provided, then the device will be used in
+  Continuous Voltage Mode.
+
+allOf:
+  - $ref: regulator.yaml#
+
+properties:
+  compatible:
+    const: pwm-regulator
+
+  pwms:
+    maxItems: 1
+
+  voltage-table:
+    description: Voltage and Duty-Cycle table.
+    $ref: /schemas/types.yaml#/definitions/uint32-matrix
+    items:
+      items:
+        - description: voltage in microvolts (uV)
+        - description: duty-cycle in percent (%)
+
+  enable-gpios:
+    description: Regulator enable GPIO
+    maxItems: 1
+
+   # Optional properties for Continuous mode:
+  pwm-dutycycle-unit:
+    description:
+      Integer value encoding the duty cycle unit. If not
+        defined, <100> is assumed, meaning that
+        pwm-dutycycle-range contains values expressed in
+        percent.
+    default: 100
+
+  pwm-dutycycle-range:
+    description:
+      Should contain 2 entries. The first entry is encoding
+        the dutycycle for regulator-min-microvolt and the
+        second one the dutycycle for regulator-max-microvolt.
+        Duty cycle values are expressed in pwm-dutycycle-unit.
+        If not defined, <0 100> is assumed.
+    $ref: /schemas/types.yaml#/definitions/uint32-array
+    items:
+      - description: the dutycycle for regulator-min-microvolt
+      - description: the dutycycle for regulator-max-microvolt
+    default: [ 0 100 ]
+
+required:
+  - compatible
+  - pwms
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/gpio/gpio.h>
+
+    // Continuous Voltage With Enable GPIO Example:
+    regulator {
+        compatible = "pwm-regulator";
+        pwms = <&pwm1 0 8448 0>;
+        enable-gpios = <&gpio0 23 GPIO_ACTIVE_HIGH>;
+        regulator-min-microvolt = <1016000>;
+        regulator-max-microvolt = <1114000>;
+        regulator-name = "vdd_logic";
+        /* unit == per-mille */
+        pwm-dutycycle-unit = <1000>;
+        /*
+        * Inverted PWM logic, and the duty cycle range is limited
+        * to 30%-70%.
+        */
+        pwm-dutycycle-range = <700 300>; /* */
+    };
+
+  - |
+    // Voltage Table Example:
+    regulator {
+        compatible = "pwm-regulator";
+        pwms = <&pwm1 0 8448 0>;
+        regulator-min-microvolt = <1016000>;
+        regulator-max-microvolt = <1114000>;
+        regulator-name = "vdd_logic";
+
+                /* Voltage Duty-Cycle */
+        voltage-table = <1114000 0>,
+            <1095000 10>,
+            <1076000 20>,
+            <1056000 30>,
+            <1036000 40>,
+            <1016000 50>;
+    };
+...

Documentation/devicetree/bindings/regulator/qcom,smd-rpm-regulator.yaml

@@ -30,6 +30,9 @@ description:
 
   For pm8841, s1, s2, s3, s4, s5, s6, s7, s8
 
+  For pm8909, s1, s2, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
+  l14, l15, l17, l18
+
   For pm8916, s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11,
   l12, l13, l14, l15, l16, l17, l18
 
@@ -78,6 +81,7 @@ properties:
       - qcom,rpm-mp5496-regulators
       - qcom,rpm-pm8226-regulators
       - qcom,rpm-pm8841-regulators
+      - qcom,rpm-pm8909-regulators
       - qcom,rpm-pm8916-regulators
       - qcom,rpm-pm8941-regulators
       - qcom,rpm-pm8950-regulators

Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.txt

-Qualcomm SPMI Regulators
-
-- compatible:
-	Usage: required
-	Value type: <string>
-	Definition: must be one of:
-			"qcom,pm8004-regulators"
-			"qcom,pm8005-regulators"
-			"qcom,pm8226-regulators"
-			"qcom,pm8841-regulators"
-			"qcom,pm8916-regulators"
-			"qcom,pm8941-regulators"
-			"qcom,pm8950-regulators"
-			"qcom,pm8994-regulators"
-			"qcom,pmi8994-regulators"
-			"qcom,pm660-regulators"
-			"qcom,pm660l-regulators"
-			"qcom,pms405-regulators"
-
-- interrupts:
-	Usage: optional
-	Value type: <prop-encoded-array>
-	Definition: List of OCP interrupts.
-
-- interrupt-names:
-	Usage: required if 'interrupts' property present
-	Value type: <string-array>
-	Definition: List of strings defining the names of the
-		    interrupts in the 'interrupts' property 1-to-1.
-		    Supported values are "ocp-<regulator_name>", where
-		    <regulator_name> corresponds to a voltage switch
-		    type regulator.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-	Usage: optional (pm8841 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_l1_l3-supply:
-- vdd_l2-supply:
-- vdd_l4_l5_l6-supply:
-- vdd_l7-supply:
-- vdd_l8_l11_l14_l15_l16-supply:
-- vdd_l9_l10_l12_l13_l17_l18-supply:
-	Usage: optional (pm8916 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1_l3-supply:
-- vdd_l2_lvs_1_2_3-supply:
-- vdd_l4_l11-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l14_l15-supply:
-- vdd_l8_l16_l18_19-supply:
-- vdd_l9_l10_l17_l22-supply:
-- vdd_l13_l20_l23_l24-supply:
-- vdd_l21-supply:
-- vin_5vs-supply:
-	Usage: optional (pm8941 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_l1_l19-supply:
-- vdd_l2_l23-supply:
-- vdd_l3-supply:
-- vdd_l4_l5_l6_l7_l16-supply:
-- vdd_l8_l11_l12_l17_l22-supply:
-- vdd_l9_l10_l13_l14_l15_l18-supply:
-- vdd_l20-supply:
-- vdd_l21-supply:
-	Usage: optional (pm8950 only)
-	Value type: <phandle>
-	Definition: reference to regulator supplying the input pin, as
-		    described in the data sheet
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-- vdd_s7-supply:
-- vdd_s8-supply:
-- vdd_s9-supply:
-- vdd_s10-supply:
-- vdd_s11-supply:
-- vdd_s12-supply:
-- vdd_l1-supply:
-- vdd_l2_l26_l28-supply:
-- vdd_l3_l11-supply:
-- vdd_l4_l27_l31-supply:
-- vdd_l5_l7-supply:
-- vdd_l6_l12_l32-supply:
-- vdd_l8_l16_l30-supply:
-- vdd_l9_l10_l18_l22-supply:
-- vdd_l13_l19_l23_l24-supply:
-- vdd_l14_l15-supply:
-- vdd_l17_l29-supply:
-- vdd_l20_l21-supply:
-- vdd_l25-supply:
-- vdd_lvs_1_2-supply:
-	Usage: optional (pm8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_l1-supply:
-	Usage: optional (pmi8994 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l6_l7-supply:
-- vdd_l2_l3-supply:
-- vdd_l5-supply:
-- vdd_l8_l9_l10_l11_l12_l13_l14-supply:
-- vdd_l15_l16_l17_l18_l19-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s5-supply:
-- vdd_s6-supply:
-	Usage: optional (pm660 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l9_l10-supply:
-- vdd_l2-supply:
-- vdd_l3_l5_l7_l8-supply:
-- vdd_l4_l6-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply:
-	Usage: optional (pm660l only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- vdd_l1_l2-supply:
-- vdd_l3_l8-supply:
-- vdd_l4-supply:
-- vdd_l5_l6-supply:
-- vdd_l10_l11_l12_l13-supply:
-- vdd_l7-supply:
-- vdd_l9-supply:
-- vdd_s1-supply:
-- vdd_s2-supply:
-- vdd_s3-supply:
-- vdd_s4-supply:
-- vdd_s5-supply
-	Usage: optional (pms405 only)
-	Value type: <phandle>
-	Definition: Reference to regulator supplying the input pin, as
-		    described in the data sheet.
-
-- qcom,saw-reg:
-	Usage: optional
-	Value type: <phandle>
-	Description: Reference to syscon node defining the SAW registers.
-
-
-The regulator node houses sub-nodes for each regulator within the device. Each
-sub-node is identified using the node's name, with valid values listed for each
-of the PMICs below.
-
-pm8004:
-	s2, s5
-
-pm8005:
-	s1, s2, s3, s4
-
-pm8841:
-	s1, s2, s3, s4, s5, s6, s7, s8
-
-pm8916:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18
-
-pm8941:
-	s1, s2, s3, s4, l1, l2, l3, l4, l5, l6, l7, l8, l9, l10, l11, l12, l13,
-	l14, l15, l16, l17, l18, l19, l20, l21, l22, l23, l24, lvs1, lvs2, lvs3,
-	5vs1, 5vs2
-
-pm8994:
-	s1, s2, s3, s4, s5, s6, s7, s8, s9, s10, s11, s12, l1, l2, l3, l4, l5,
-	l6, l7, l8, l9, l10, l11, l12, l13, l14, l15, l16, l17, l18, l19, l20,
-	l21, l22, l23, l24, l25, l26, l27, l28, l29, l30, l31, l32, lvs1, lvs2
-
-pmi8994:
-	s1, s2, s3, l1
-
-The content of each sub-node is defined by the standard binding for regulators -
-see regulator.txt - with additional custom properties described below:
-
-- regulator-initial-mode:
-	Usage: optional
-	Value type: <u32>
-	Description: 2 = Set initial mode to auto mode (automatically select
-		    between HPM and LPM); not available on boost type
-		    regulators.
-
-		    1 = Set initial mode to high power mode (HPM), also referred
-		    to as NPM. HPM consumes more ground current than LPM, but
-		    it can source significantly higher load current. HPM is not
-		    available on boost type regulators. For voltage switch type
-		    regulators, HPM implies that over current protection and
-		    soft start are active all the time.
-
-		    0 = Set initial mode to low power mode (LPM).
-
-- qcom,ocp-max-retries:
-	Usage: optional
-	Value type: <u32>
-	Description: Maximum number of times to try toggling a voltage switch
-		     off and back on as a result of consecutive over current
-		     events.
-
-- qcom,ocp-retry-delay:
-	Usage: optional
-	Value type: <u32>
-	Description: Time to delay in milliseconds between each voltage switch
-		     toggle after an over current event takes place.
-
-- qcom,pin-ctrl-enable:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     enable the regulator, if any; supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-
-- qcom,pin-ctrl-hpm:
-	Usage: optional
-	Value type: <u32>
-	Description: Bit mask specifying which hardware pins should be used to
-		     force the regulator into high power mode, if any;
-		     supported bits are:
-			0 = ignore all hardware enable signals
-			BIT(0) = follow HW0_EN signal
-			BIT(1) = follow HW1_EN signal
-			BIT(2) = follow HW2_EN signal
-			BIT(3) = follow HW3_EN signal
-			BIT(4) = follow PMIC awake state
-
-- qcom,vs-soft-start-strength:
-	Usage: optional
-	Value type: <u32>
-	Description: This property sets the soft start strength for voltage
-		     switch type regulators; supported values are:
-			0 = 0.05 uA
-			1 = 0.25 uA
-			2 = 0.55 uA
-			3 = 0.75 uA
-
-- qcom,saw-slave:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang slave. Will not be configured.
-
-- qcom,saw-leader:
-	Usage: optional
-	Value type: <boo>
-	Description: SAW controlled gang leader. Will be configured as
-		     SAW regulator.
-
-Example:
-
-	regulators {
-		compatible = "qcom,pm8941-regulators";
-		vdd_l1_l3-supply = <&s1>;
-
-		s1: s1 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1400000>;
-		};
-
-		...
-
-		l1: l1 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		....
-	};
-
-Example 2:
-
-	saw3: syscon@9A10000 {
-		compatible = "syscon";
-		reg = <0x9A10000 0x1000>;
-	};
-
-	...
-
-	spm-regulators {
-		compatible = "qcom,pm8994-regulators";
-		qcom,saw-reg = <&saw3>;
-		s8 {
-			qcom,saw-slave;
-		};
-		s9 {
-			qcom,saw-slave;
-		};
-		s10 {
-			qcom,saw-slave;
-		};
-		pm8994_s11_saw: s11 {
-			qcom,saw-leader;
-			regulator-always-on;
-			regulator-min-microvolt = <900000>;
-			regulator-max-microvolt = <1140000>;
-		};
-	};

Documentation/devicetree/bindings/regulator/qcom,spmi-regulator.yaml

+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/regulator/qcom,spmi-regulator.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm SPMI Regulators
+
+maintainers:
+  - Robert Marko <robimarko@gmail.com>
+
+properties:
+  compatible:
+    enum:
+      - qcom,pm660-regulators
+      - qcom,pm660l-regulators
+      - qcom,pm8004-regulators
+      - qcom,pm8005-regulators
+      - qcom,pm8226-regulators
+      - qcom,pm8841-regulators
+      - qcom,pm8916-regulators
+      - qcom,pm8941-regulators
+      - qcom,pm8950-regulators
+      - qcom,pm8994-regulators
+      - qcom,pmi8994-regulators
+      - qcom,pmp8074-regulators
+      - qcom,pms405-regulators
+
+  qcom,saw-reg:
+    description: Reference to syscon node defining the SAW registers
+    $ref: /schemas/types.yaml#/definitions/phandle
+
+patternProperties:
+  "^(5vs[1-2]|(l|s)[1-9][0-9]?|lvs[1-3])$":
+    description: List of regulators and its properties
+    type: object
+    $ref: regulator.yaml#
+
+    properties:
+      qcom,ocp-max-retries:
+        description:
+          Maximum number of times to try toggling a voltage switch off and
+          back on as a result of consecutive over current events
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      qcom,ocp-retry-delay:
+        description:
+          Time to delay in milliseconds between each voltage switch toggle
+          after an over current event takes place
+        $ref: /schemas/types.yaml#/definitions/uint32
+
+      qcom,pin-ctrl-enable:
+        description:
+          Bit mask specifying which hardware pins should be used to enable the
+          regulator, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 15
+
+      qcom,pin-ctrl-hpm:
+        description:
+          Bit mask specifying which hardware pins should be used to force the
+          regulator into high power mode, if any.
+          Supported bits are
+          0 = ignore all hardware enable signals
+          BIT(0) = follow HW0_EN signal
+          BIT(1) = follow HW1_EN signal
+          BIT(2) = follow HW2_EN signal
+          BIT(3) = follow HW3_EN signal
+          BIT(4) = follow PMIC awake state
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 31
+
+      qcom,vs-soft-start-strength:
+        description:
+          This property sets the soft start strength for voltage switch type
+          regulators.
+          Supported values are
+          0 = 0.05 uA
+          1 = 0.25 uA
+          2 = 0.55 uA
+          3 = 0.75 uA
+        $ref: /schemas/types.yaml#/definitions/uint32
+        minimum: 0
+        maximum: 3
+
+      qcom,saw-slave:
+        description: SAW controlled gang slave. Will not be configured.
+        type: boolean
+
+      qcom,saw-leader:
+        description:
+          SAW controlled gang leader. Will be configured as SAW regulator.
+        type: boolean
+
+      unevaluatedProperties: false
+
+required:
+  - compatible
+
+allOf:
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm660-regulators
+    then:
+      properties:
+        vdd_l15_l16_l17_l18_l19-supply: true
+        vdd_l1_l6_l7-supply: true
+        vdd_l2_l3-supply: true
+        vdd_l5-supply: true
+        vdd_l8_l9_l10_l11_l12_l13_l14-supply: true
+      patternProperties:
+        "^vdd_s[1-6]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm660l-regulators
+    then:
+      properties:
+        vdd_l1_l9_l10-supply: true
+        vdd_l2-supply: true
+        vdd_l3_l5_l7_l8-supply: true
+        vdd_l4_l6-supply: true
+      patternProperties:
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8004-regulators
+    then:
+      patternProperties:
+        "^vdd_s[25]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8005-regulators
+    then:
+      patternProperties:
+        "^vdd_s[1-4]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8226-regulators
+    then:
+      properties:
+        vdd_l10_l11_l13-supply: true
+        vdd_l12_l14-supply: true
+        vdd_l15_l16_l17_l18-supply: true
+        vdd_l19_l20_l21_l22_l23_l28-supply: true
+        vdd_l1_l2_l4_l5-supply: true
+        vdd_l25-supply: true
+        vdd_l3_l24_l26-supply: true
+        vdd_l6_l7_l8_l9_l27-supply: true
+        vdd_lvs1-supply: true
+      patternProperties:
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8841-regulators
+    then:
+      patternProperties:
+        "^vdd_s[1-8]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8916-regulators
+    then:
+      properties:
+        vdd_l1_l3-supply: true
+        vdd_l4_l5_l6-supply: true
+        vdd_l8_l11_l14_l15_l16-supply: true
+        vdd_l9_l10_l12_l13_l17_l18-supply: true
+      patternProperties:
+        "^vdd_l[27]-supply$": true
+        "^vdd_s[1-4]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8941-regulators
+    then:
+      properties:
+        interrupts:
+          items:
+            - description: Over-current protection interrupt for 5V S1
+            - description: Over-current protection interrupt for 5V S2
+        interrupt-names:
+          items:
+            - const: ocp-5vs1
+            - const: ocp-5vs2
+        vdd_l13_l20_l23_l24-supply: true
+        vdd_l1_l3-supply: true
+        vdd_l21-supply: true
+        vdd_l2_lvs_1_2_3-supply: true
+        vdd_l4_l11-supply: true
+        vdd_l5_l7-supply: true
+        vdd_l6_l12_l14_l15-supply: true
+        vdd_l8_l16_l18_19-supply: true
+        vdd_l9_l10_l17_l22-supply: true
+        vin_5vs-supply: true
+      patternProperties:
+        "^vdd_s[1-3]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8950-regulators
+    then:
+      properties:
+        vdd_l1_l19-supply: true
+        vdd_l20-supply: true
+        vdd_l21-supply: true
+        vdd_l2_l23-supply: true
+        vdd_l3-supply: true
+        vdd_l4_l5_l6_l7_l16-supply: true
+        vdd_l8_l11_l12_l17_l22-supply: true
+        vdd_l9_l10_l13_l14_l15_l18-supply: true
+      patternProperties:
+        "^vdd_s[1-6]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pm8994-regulators
+    then:
+      properties:
+        vdd_l1-supply: true
+        vdd_l13_l19_l23_l24-supply: true
+        vdd_l14_l15-supply: true
+        vdd_l17_l29-supply: true
+        vdd_l20_l21-supply: true
+        vdd_l25-supply: true
+        vdd_l2_l26_l28-supply: true
+        vdd_l3_l11-supply: true
+        vdd_l4_l27_l31-supply: true
+        vdd_l5_l7-supply: true
+        vdd_l6_l12_l32-supply: true
+        vdd_l8_l16_l30-supply: true
+        vdd_l9_l10_l18_l22-supply: true
+        vdd_lvs_1_2-supply: true
+      patternProperties:
+        "^vdd_s[1-9][0-2]?-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pmi8994-regulators
+    then:
+      properties:
+        vdd_l1-supply: true
+      patternProperties:
+        "^vdd_s[1-3]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pmp8074-regulators
+    then:
+      properties:
+        vdd_l10_l11_l12_l13-supply: true
+        vdd_l1_l2-supply: true
+        vdd_l3_l8-supply: true
+        vdd_l5_l6_l15-supply: true
+      patternProperties:
+        "^vdd_l[479]-supply$": true
+        "^vdd_s[1-5]-supply$": true
+  - if:
+      properties:
+        compatible:
+          contains:
+            enum:
+              - qcom,pms405-regulators
+    then:
+      properties:
+        vdd_s3-supply: true
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    regulators {
+      compatible = "qcom,pm8941-regulators";
+      vdd_l1_l3-supply = <&s1>;
+
+      s1: s1 {
+        regulator-min-microvolt = <1300000>;
+        regulator-max-microvolt = <1400000>;
+      };
+
+      l1: l1 {
+        regulator-min-microvolt = <1225000>;
+        regulator-max-microvolt = <1300000>;
+      };
+    };
+...

Documentation/devicetree/bindings/regulator/regulator.yaml

@@ -23,6 +23,7 @@ properties:
 
   regulator-microvolt-offset:
     description: Offset applied to voltages to compensate for voltage drops
+    $ref: "/schemas/types.yaml#/definitions/uint32"
 
   regulator-min-microamp:
     description: smallest current consumers may set

drivers/regulator/Kconfig

@@ -546,6 +546,16 @@ config REGULATOR_MAX1586
 	  regulator via I2C bus. The provided regulator is suitable
 	  for PXA27x chips to control VCC_CORE and VCC_USIM voltages.
 
+config REGULATOR_MAX597X
+	tristate "Maxim 597x power switch and monitor"
+	depends on I2C
+	depends on OF
+	depends on MFD_MAX597X
+	help
+	  This driver controls a Maxim 5970/5978 switch via I2C bus.
+	  The MAX5970/5978 is a smart switch with no output regulation, but
+	  fault protection and voltage and current monitoring capabilities.
+
 config REGULATOR_MAX77620
 	tristate "Maxim 77620/MAX20024 voltage regulator"
 	depends on MFD_MAX77620 || COMPILE_TEST
@@ -804,6 +814,14 @@ config REGULATOR_MT6360
 	  2-channel buck with Thermal Shutdown and Overload Protection
 	  6-channel High PSRR and Low Dropout LDO.
 
+config REGULATOR_MT6370
+	tristate "MT6370 SubPMIC Regulator"
+	depends on MFD_MT6370
+	help
+	  Say Y here to enable MT6370 regulator support.
+	  This driver supports the control for DisplayBias voltages and one
+	  general purpose LDO which is commonly used to drive the vibrator.
+
 config REGULATOR_MT6380
 	tristate "MediaTek MT6380 PMIC"
 	depends on MTK_PMIC_WRAP
@@ -1047,6 +1065,16 @@ config REGULATOR_RT5033
 	  RT5033 PMIC. The device supports multiple regulators like
 	  current source, LDO and Buck.
 
+config REGULATOR_RT5120
+	tristate "Richtek RT5120 PMIC Regulators"
+	depends on MFD_RT5120
+	help
+	  This adds support for voltage regulator in Richtek RT5120 PMIC.
+	  It integrates 4 channels buck controller, 1 channel LDO, 1 EXTEN
+	  to control external power source. Only BUCK1 is adjustable from
+	  600mV to 1395mV, per step 6.250mV. The others are all fixed voltage
+	  by external hardware circuit.
+
 config REGULATOR_RT5190A
 	tristate "Richtek RT5190A PMIC"
 	depends on I2C

drivers/regulator/Makefile

@@ -67,6 +67,7 @@ obj-$(CONFIG_REGULATOR_LTC3589) += ltc3589.o
 obj-$(CONFIG_REGULATOR_LTC3676) += ltc3676.o
 obj-$(CONFIG_REGULATOR_MAX14577) += max14577-regulator.o
 obj-$(CONFIG_REGULATOR_MAX1586) += max1586.o
+obj-$(CONFIG_REGULATOR_MAX597X) += max597x-regulator.o
 obj-$(CONFIG_REGULATOR_MAX77620) += max77620-regulator.o
 obj-$(CONFIG_REGULATOR_MAX77650) += max77650-regulator.o
 obj-$(CONFIG_REGULATOR_MAX8649)	+= max8649.o
@@ -97,6 +98,7 @@ obj-$(CONFIG_REGULATOR_MT6323)	+= mt6323-regulator.o
 obj-$(CONFIG_REGULATOR_MT6358)	+= mt6358-regulator.o
 obj-$(CONFIG_REGULATOR_MT6359)	+= mt6359-regulator.o
 obj-$(CONFIG_REGULATOR_MT6360) += mt6360-regulator.o
+obj-$(CONFIG_REGULATOR_MT6370) += mt6370-regulator.o
 obj-$(CONFIG_REGULATOR_MT6380)	+= mt6380-regulator.o
 obj-$(CONFIG_REGULATOR_MT6397)	+= mt6397-regulator.o
 obj-$(CONFIG_REGULATOR_MTK_DVFSRC) += mtk-dvfsrc-regulator.o
@@ -126,6 +128,7 @@ obj-$(CONFIG_REGULATOR_ROHM)	+= rohm-regulator.o
 obj-$(CONFIG_REGULATOR_RT4801)	+= rt4801-regulator.o
 obj-$(CONFIG_REGULATOR_RT4831)	+= rt4831-regulator.o
 obj-$(CONFIG_REGULATOR_RT5033)	+= rt5033-regulator.o
+obj-$(CONFIG_REGULATOR_RT5120)	+= rt5120-regulator.o
 obj-$(CONFIG_REGULATOR_RT5190A) += rt5190a-regulator.o
 obj-$(CONFIG_REGULATOR_RT5759)	+= rt5759-regulator.o
 obj-$(CONFIG_REGULATOR_RT6160)	+= rt6160-regulator.o

drivers/regulator/core.c

@@ -1565,6 +1565,9 @@ static int set_machine_constraints(struct regulator_dev *rdev)
 			rdev->constraints->always_on = true;
 	}
 
+	if (rdev->desc->off_on_delay)
+		rdev->last_off = ktime_get();
+
 	/* If the constraints say the regulator should be on at this point
 	 * and we have control then make sure it is enabled.
 	 */
@@ -1592,8 +1595,6 @@ static int set_machine_constraints(struct regulator_dev *rdev)
 
 		if (rdev->constraints->always_on)
 			rdev->use_count++;
-	} else if (rdev->desc->off_on_delay) {
-		rdev->last_off = ktime_get();
 	}
 
 	print_constraints(rdev);
@@ -4783,22 +4784,26 @@ int regulator_bulk_get(struct device *dev, int num_consumers,
 		consumers[i].consumer = regulator_get(dev,
 						      consumers[i].supply);
 		if (IS_ERR(consumers[i].consumer)) {
-			ret = PTR_ERR(consumers[i].consumer);
 			consumers[i].consumer = NULL;
+			ret = dev_err_probe(dev, PTR_ERR(consumers[i].consumer),
+					    "Failed to get supply '%s'",
+					    consumers[i].supply);
 			goto err;
 		}
+
+		if (consumers[i].init_load_uA > 0) {
+			ret = regulator_set_load(consumers[i].consumer,
+						 consumers[i].init_load_uA);
+			if (ret) {
+				i++;
+				goto err;
+			}
+		}
 	}
 
 	return 0;
 
 err:
-	if (ret != -EPROBE_DEFER)
-		dev_err(dev, "Failed to get supply '%s': %pe\n",
-			consumers[i].supply, ERR_PTR(ret));
-	else
-		dev_dbg(dev, "Failed to get supply '%s', deferring\n",
-			consumers[i].supply);
-
 	while (--i >= 0)
 		regulator_put(consumers[i].consumer);
 

drivers/regulator/devres.c

@@ -166,6 +166,34 @@ int devm_regulator_bulk_get(struct device *dev, int num_consumers,
 }
 EXPORT_SYMBOL_GPL(devm_regulator_bulk_get);
 
+/**
+ * devm_regulator_bulk_get_const - devm_regulator_bulk_get() w/ const data
+ *
+ * @dev:           device to supply
+ * @num_consumers: number of consumers to register
+ * @in_consumers:  const configuration of consumers
+ * @out_consumers: in_consumers is copied here and this is passed to
+ *		   devm_regulator_bulk_get().
+ *
+ * This is a convenience function to allow bulk regulator configuration
+ * to be stored "static const" in files.
+ *
+ * Return: 0 on success, an errno on failure.
+ */
+int devm_regulator_bulk_get_const(struct device *dev, int num_consumers,
+				  const struct regulator_bulk_data *in_consumers,
+				  struct regulator_bulk_data **out_consumers)
+{
+	*out_consumers = devm_kmemdup(dev, in_consumers,
+				      num_consumers * sizeof(*in_consumers),
+				      GFP_KERNEL);
+	if (*out_consumers == NULL)
+		return -ENOMEM;
+
+	return devm_regulator_bulk_get(dev, num_consumers, *out_consumers);
+}
+EXPORT_SYMBOL_GPL(devm_regulator_bulk_get_const);
+
 static void devm_rdev_release(struct device *dev, void *res)
 {
 	regulator_unregister(*(struct regulator_dev **)res);

drivers/regulator/max597x-regulator.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * Device driver for regulators in MAX5970 and MAX5978 IC
+ *
+ * Copyright (c) 2022 9elements GmbH
+ *
+ * Author: Patrick Rudolph <patrick.rudolph@9elements.com>
+ */
+
+#include <linux/bitops.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/module.h>
+#include <linux/io.h>
+#include <linux/of.h>
+#include <linux/i2c.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+#include <linux/platform_device.h>
+
+#include <linux/mfd/max597x.h>
+
+struct max597x_regulator {
+	int num_switches, mon_rng, irng, shunt_micro_ohms, lim_uA;
+	struct regmap *regmap;
+};
+
+enum max597x_regulator_id {
+	MAX597X_SW0,
+	MAX597X_SW1,
+};
+
+static int max597x_uvp_ovp_check_mode(struct regulator_dev *rdev, int severity)
+{
+	int ret, reg;
+
+	/* Status1 register contains the soft strap values sampled at POR */
+	ret = regmap_read(rdev->regmap, MAX5970_REG_STATUS1, &reg);
+	if (ret)
+		return ret;
+
+	/* Check soft straps match requested mode */
+	if (severity == REGULATOR_SEVERITY_PROT) {
+		if (STATUS1_PROT(reg) != STATUS1_PROT_SHUTDOWN)
+			return -EOPNOTSUPP;
+
+		return 0;
+	}
+	if (STATUS1_PROT(reg) == STATUS1_PROT_SHUTDOWN)
+		return -EOPNOTSUPP;
+
+	return 0;
+}
+
+static int max597x_set_vp(struct regulator_dev *rdev, int lim_uV, int severity,
+			  bool enable, bool overvoltage)
+{
+	int off_h, off_l, reg, ret;
+	struct max597x_regulator *data = rdev_get_drvdata(rdev);
+	int channel = rdev_get_id(rdev);
+
+	if (overvoltage) {
+		if (severity == REGULATOR_SEVERITY_WARN) {
+			off_h = MAX5970_REG_CH_OV_WARN_H(channel);
+			off_l = MAX5970_REG_CH_OV_WARN_L(channel);
+		} else {
+			off_h = MAX5970_REG_CH_OV_CRIT_H(channel);
+			off_l = MAX5970_REG_CH_OV_CRIT_L(channel);
+		}
+	} else {
+		if (severity == REGULATOR_SEVERITY_WARN) {
+			off_h = MAX5970_REG_CH_UV_WARN_H(channel);
+			off_l = MAX5970_REG_CH_UV_WARN_L(channel);
+		} else {
+			off_h = MAX5970_REG_CH_UV_CRIT_H(channel);
+			off_l = MAX5970_REG_CH_UV_CRIT_L(channel);
+		}
+	}
+
+	if (enable)
+		/* reg = ADC_MASK * (lim_uV / 1000000) / (data->mon_rng / 1000000) */
+		reg = ADC_MASK * lim_uV / data->mon_rng;
+	else
+		reg = 0;
+
+	ret = regmap_write(rdev->regmap, off_h, MAX5970_VAL2REG_H(reg));
+	if (ret)
+		return ret;
+
+	ret = regmap_write(rdev->regmap, off_l, MAX5970_VAL2REG_L(reg));
+	if (ret)
+		return ret;
+
+	return 0;
+}
+
+static int max597x_set_uvp(struct regulator_dev *rdev, int lim_uV, int severity,
+			   bool enable)
+{
+	int ret;
+
+	/*
+	 * MAX5970 has enable control as a special value in limit reg. Can't
+	 * set limit but keep feature disabled or enable W/O given limit.
+	 */
+	if ((lim_uV && !enable) || (!lim_uV && enable))
+		return -EINVAL;
+
+	ret = max597x_uvp_ovp_check_mode(rdev, severity);
+	if (ret)
+		return ret;
+
+	return max597x_set_vp(rdev, lim_uV, severity, enable, false);
+}
+
+static int max597x_set_ovp(struct regulator_dev *rdev, int lim_uV, int severity,
+			   bool enable)
+{
+	int ret;
+
+	/*
+	 * MAX5970 has enable control as a special value in limit reg. Can't
+	 * set limit but keep feature disabled or enable W/O given limit.
+	 */
+	if ((lim_uV && !enable) || (!lim_uV && enable))
+		return -EINVAL;
+
+	ret = max597x_uvp_ovp_check_mode(rdev, severity);
+	if (ret)
+		return ret;
+
+	return max597x_set_vp(rdev, lim_uV, severity, enable, true);
+}
+
+static int max597x_set_ocp(struct regulator_dev *rdev, int lim_uA,
+			   int severity, bool enable)
+{
+	int ret, val, reg;
+	unsigned int vthst, vthfst;
+
+	struct max597x_regulator *data = rdev_get_drvdata(rdev);
+	int rdev_id = rdev_get_id(rdev);
+	/*
+	 * MAX5970 doesn't has enable control for ocp.
+	 * If limit is specified but enable is not set then hold the value in
+	 * variable & later use it when ocp needs to be enabled.
+	 */
+	if (lim_uA != 0 && lim_uA != data->lim_uA)
+		data->lim_uA = lim_uA;
+
+	if (severity != REGULATOR_SEVERITY_PROT)
+		return -EINVAL;
+
+	if (enable) {
+
+		/* Calc Vtrip threshold in uV. */
+		vthst =
+		    div_u64(mul_u32_u32(data->shunt_micro_ohms, data->lim_uA),
+			    1000000);
+
+		/*
+		 * As recommended in datasheed, add 20% margin to avoid
+		 * spurious event & passive component tolerance.
+		 */
+		vthst = div_u64(mul_u32_u32(vthst, 120), 100);
+
+		/* Calc fast Vtrip threshold in uV */
+		vthfst = vthst * (MAX5970_FAST2SLOW_RATIO / 100);
+
+		if (vthfst > data->irng) {
+			dev_err(&rdev->dev, "Current limit out of range\n");
+			return -EINVAL;
+		}
+		/* Fast trip threshold to be programmed */
+		val = div_u64(mul_u32_u32(0xFF, vthfst), data->irng);
+	} else
+		/*
+		 * Since there is no option to disable ocp, set limit to max
+		 * value
+		 */
+		val = 0xFF;
+
+	reg = MAX5970_REG_DAC_FAST(rdev_id);
+	ret = regmap_write(rdev->regmap, reg, val);
+
+	return ret;
+}
+
+static int max597x_get_status(struct regulator_dev *rdev)
+{
+	int val, ret;
+
+	ret = regmap_read(rdev->regmap, MAX5970_REG_STATUS3, &val);
+	if (ret)
+		return REGULATOR_FAILED_RETRY;
+
+	if (val & MAX5970_STATUS3_ALERT)
+		return REGULATOR_STATUS_ERROR;
+
+	ret = regulator_is_enabled_regmap(rdev);
+	if (ret < 0)
+		return ret;
+
+	if (ret)
+		return REGULATOR_STATUS_ON;
+
+	return REGULATOR_STATUS_OFF;
+}
+
+static const struct regulator_ops max597x_switch_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.get_status = max597x_get_status,
+	.set_over_voltage_protection = max597x_set_ovp,
+	.set_under_voltage_protection = max597x_set_uvp,
+	.set_over_current_protection = max597x_set_ocp,
+};
+
+static int max597x_dt_parse(struct device_node *np,
+			    const struct regulator_desc *desc,
+			    struct regulator_config *cfg)
+{
+	struct max597x_regulator *data = cfg->driver_data;
+	int ret = 0;
+
+	ret =
+	    of_property_read_u32(np, "shunt-resistor-micro-ohms",
+				 &data->shunt_micro_ohms);
+	if (ret < 0)
+		dev_err(cfg->dev,
+			"property 'shunt-resistor-micro-ohms' not found, err %d\n",
+			ret);
+	return ret;
+
+}
+
+#define MAX597X_SWITCH(_ID, _ereg, _chan, _supply) {     \
+	.name            = #_ID,                         \
+	.of_match        = of_match_ptr(#_ID),           \
+	.ops             = &max597x_switch_ops,          \
+	.regulators_node = of_match_ptr("regulators"),   \
+	.type            = REGULATOR_VOLTAGE,            \
+	.id              = MAX597X_##_ID,                \
+	.owner           = THIS_MODULE,                  \
+	.supply_name     = _supply,                      \
+	.enable_reg      = _ereg,                        \
+	.enable_mask     = CHXEN((_chan)),               \
+	.of_parse_cb	 = max597x_dt_parse,		 \
+}
+
+static const struct regulator_desc regulators[] = {
+	MAX597X_SWITCH(SW0, MAX5970_REG_CHXEN, 0, "vss1"),
+	MAX597X_SWITCH(SW1, MAX5970_REG_CHXEN, 1, "vss2"),
+};
+
+static int max597x_regmap_read_clear(struct regmap *map, unsigned int reg,
+				     unsigned int *val)
+{
+	int ret;
+
+	ret = regmap_read(map, reg, val);
+	if (ret)
+		return ret;
+
+	if (*val)
+		return regmap_write(map, reg, *val);
+
+	return 0;
+}
+
+static int max597x_irq_handler(int irq, struct regulator_irq_data *rid,
+			       unsigned long *dev_mask)
+{
+	struct regulator_err_state *stat;
+	struct max597x_regulator *d = (struct max597x_regulator *)rid->data;
+	int val, ret, i;
+
+	ret = max597x_regmap_read_clear(d->regmap, MAX5970_REG_FAULT0, &val);
+	if (ret)
+		return REGULATOR_FAILED_RETRY;
+
+	*dev_mask = 0;
+	for (i = 0; i < d->num_switches; i++) {
+		stat = &rid->states[i];
+		stat->notifs = 0;
+		stat->errors = 0;
+	}
+
+	for (i = 0; i < d->num_switches; i++) {
+		stat = &rid->states[i];
+
+		if (val & UV_STATUS_CRIT(i)) {
+			*dev_mask |= 1 << i;
+			stat->notifs |= REGULATOR_EVENT_UNDER_VOLTAGE;
+			stat->errors |= REGULATOR_ERROR_UNDER_VOLTAGE;
+		} else if (val & UV_STATUS_WARN(i)) {
+			*dev_mask |= 1 << i;
+			stat->notifs |= REGULATOR_EVENT_UNDER_VOLTAGE_WARN;
+			stat->errors |= REGULATOR_ERROR_UNDER_VOLTAGE_WARN;
+		}
+	}
+
+	ret = max597x_regmap_read_clear(d->regmap, MAX5970_REG_FAULT1, &val);
+	if (ret)
+		return REGULATOR_FAILED_RETRY;
+
+	for (i = 0; i < d->num_switches; i++) {
+		stat = &rid->states[i];
+
+		if (val & OV_STATUS_CRIT(i)) {
+			*dev_mask |= 1 << i;
+			stat->notifs |= REGULATOR_EVENT_REGULATION_OUT;
+			stat->errors |= REGULATOR_ERROR_REGULATION_OUT;
+		} else if (val & OV_STATUS_WARN(i)) {
+			*dev_mask |= 1 << i;
+			stat->notifs |= REGULATOR_EVENT_OVER_VOLTAGE_WARN;
+			stat->errors |= REGULATOR_ERROR_OVER_VOLTAGE_WARN;
+		}
+	}
+
+	ret = max597x_regmap_read_clear(d->regmap, MAX5970_REG_FAULT2, &val);
+	if (ret)
+		return REGULATOR_FAILED_RETRY;
+
+	for (i = 0; i < d->num_switches; i++) {
+		stat = &rid->states[i];
+
+		if (val & OC_STATUS_WARN(i)) {
+			*dev_mask |= 1 << i;
+			stat->notifs |= REGULATOR_EVENT_OVER_CURRENT_WARN;
+			stat->errors |= REGULATOR_ERROR_OVER_CURRENT_WARN;
+		}
+	}
+
+	ret = regmap_read(d->regmap, MAX5970_REG_STATUS0, &val);
+	if (ret)
+		return REGULATOR_FAILED_RETRY;
+
+	for (i = 0; i < d->num_switches; i++) {
+		stat = &rid->states[i];
+
+		if ((val & MAX5970_CB_IFAULTF(i))
+		    || (val & MAX5970_CB_IFAULTS(i))) {
+			*dev_mask |= 1 << i;
+			stat->notifs |=
+			    REGULATOR_EVENT_OVER_CURRENT |
+			    REGULATOR_EVENT_DISABLE;
+			stat->errors |=
+			    REGULATOR_ERROR_OVER_CURRENT | REGULATOR_ERROR_FAIL;
+
+			/* Clear the sub-IRQ status */
+			regulator_disable_regmap(stat->rdev);
+		}
+	}
+	return 0;
+}
+
+static const struct regmap_config max597x_regmap_config = {
+	.reg_bits = 8,
+	.val_bits = 8,
+	.max_register = MAX_REGISTERS,
+};
+
+static int max597x_adc_range(struct regmap *regmap, const int ch,
+			     u32 *irng, u32 *mon_rng)
+{
+	unsigned int reg;
+	int ret;
+
+	/* Decode current ADC range */
+	ret = regmap_read(regmap, MAX5970_REG_STATUS2, &reg);
+	if (ret)
+		return ret;
+	switch (MAX5970_IRNG(reg, ch)) {
+	case 0:
+		*irng = 100000;	/* 100 mV */
+		break;
+	case 1:
+		*irng = 50000;	/* 50 mV */
+		break;
+	case 2:
+		*irng = 25000;	/* 25 mV */
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	/* Decode current voltage monitor range */
+	ret = regmap_read(regmap, MAX5970_REG_MON_RANGE, &reg);
+	if (ret)
+		return ret;
+
+	*mon_rng = MAX5970_MON_MAX_RANGE_UV >> MAX5970_MON(reg, ch);
+
+	return 0;
+}
+
+static int max597x_setup_irq(struct device *dev,
+			     int irq,
+			     struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES],
+			     int num_switches, struct max597x_regulator *data)
+{
+	struct regulator_irq_desc max597x_notif = {
+		.name = "max597x-irq",
+		.map_event = max597x_irq_handler,
+		.data = data,
+	};
+	int errs = REGULATOR_ERROR_UNDER_VOLTAGE |
+	    REGULATOR_ERROR_UNDER_VOLTAGE_WARN |
+	    REGULATOR_ERROR_OVER_VOLTAGE_WARN |
+	    REGULATOR_ERROR_REGULATION_OUT |
+	    REGULATOR_ERROR_OVER_CURRENT |
+	    REGULATOR_ERROR_OVER_CURRENT_WARN | REGULATOR_ERROR_FAIL;
+	void *irq_helper;
+
+	/* Register notifiers - can fail if IRQ is not given */
+	irq_helper = devm_regulator_irq_helper(dev, &max597x_notif,
+					       irq, 0, errs, NULL,
+					       &rdevs[0], num_switches);
+	if (IS_ERR(irq_helper)) {
+		if (PTR_ERR(irq_helper) == -EPROBE_DEFER)
+			return -EPROBE_DEFER;
+
+		dev_warn(dev, "IRQ disabled %pe\n", irq_helper);
+	}
+
+	return 0;
+}
+
+static int max597x_regulator_probe(struct platform_device *pdev)
+{
+
+
+	struct max597x_data *max597x = dev_get_drvdata(pdev->dev.parent);
+	struct max597x_regulator *data;
+
+	struct regulator_config config = { };
+	struct regulator_dev *rdev;
+	struct regulator_dev *rdevs[MAX5970_NUM_SWITCHES];
+	int num_switches = max597x->num_switches;
+	int ret, i;
+
+	for (i = 0; i < num_switches; i++) {
+		data =
+		    devm_kzalloc(max597x->dev, sizeof(struct max597x_regulator),
+				 GFP_KERNEL);
+		if (!data)
+			return -ENOMEM;
+
+		data->num_switches = num_switches;
+		data->regmap = max597x->regmap;
+
+		ret = max597x_adc_range(data->regmap, i, &max597x->irng[i], &max597x->mon_rng[i]);
+		if (ret < 0)
+			return ret;
+
+		data->irng = max597x->irng[i];
+		data->mon_rng = max597x->mon_rng[i];
+
+		config.dev = max597x->dev;
+		config.driver_data = (void *)data;
+		config.regmap = data->regmap;
+		rdev = devm_regulator_register(max597x->dev,
+					       &regulators[i], &config);
+		if (IS_ERR(rdev)) {
+			dev_err(max597x->dev, "failed to register regulator %s\n",
+				regulators[i].name);
+			return PTR_ERR(rdev);
+		}
+		rdevs[i] = rdev;
+		max597x->shunt_micro_ohms[i] = data->shunt_micro_ohms;
+	}
+
+	if (max597x->irq) {
+		ret =
+		    max597x_setup_irq(max597x->dev, max597x->irq, rdevs, num_switches,
+				      data);
+		if (ret) {
+			dev_err(max597x->dev, "IRQ setup failed");
+			return ret;
+		}
+	}
+
+	return ret;
+}
+
+static struct platform_driver max597x_regulator_driver = {
+	.driver = {
+		.name = "max597x-regulator",
+	},
+	.probe = max597x_regulator_probe,
+};
+
+module_platform_driver(max597x_regulator_driver);
+
+
+MODULE_AUTHOR("Patrick Rudolph <patrick.rudolph@9elements.com>");
+MODULE_DESCRIPTION("MAX5970_hot-swap controller driver");
+MODULE_LICENSE("GPL v2");

drivers/regulator/mp5416.c

@@ -6,14 +6,14 @@
 //
 // Author: Saravanan Sekar <sravanhome@gmail.com>
 
-#include <linux/kernel.h>
-#include <linux/module.h>
-#include <linux/init.h>
 #include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/init.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
 #include <linux/platform_device.h>
 #include <linux/regmap.h>
 #include <linux/regulator/driver.h>
-#include <linux/i2c.h>
 
 #define MP5416_REG_CTL0			0x00
 #define MP5416_REG_CTL1			0x01
@@ -174,10 +174,22 @@ static struct regulator_desc mp5416_regulators_desc[MP5416_MAX_REGULATORS] = {
 	MP5416LDO("ldo4", 4, BIT(1)),
 };
 
+static struct regulator_desc mp5496_regulators_desc[MP5416_MAX_REGULATORS] = {
+	MP5416BUCK("buck1", 1, mp5416_I_limits1, MP5416_REG_CTL1, BIT(0), 1),
+	MP5416BUCK("buck2", 2, mp5416_I_limits2, MP5416_REG_CTL1, BIT(1), 1),
+	MP5416BUCK("buck3", 3, mp5416_I_limits1, MP5416_REG_CTL1, BIT(2), 1),
+	MP5416BUCK("buck4", 4, mp5416_I_limits2, MP5416_REG_CTL2, BIT(5), 1),
+	MP5416LDO("ldo1", 1, BIT(4)),
+	MP5416LDO("ldo2", 2, BIT(3)),
+	MP5416LDO("ldo3", 3, BIT(2)),
+	MP5416LDO("ldo4", 4, BIT(1)),
+};
+
 static int mp5416_i2c_probe(struct i2c_client *client)
 {
 	struct device *dev = &client->dev;
 	struct regulator_config config = { NULL, };
+	static const struct regulator_desc *desc;
 	struct regulator_dev *rdev;
 	struct regmap *regmap;
 	int i;
@@ -188,12 +200,16 @@ static int mp5416_i2c_probe(struct i2c_client *client)
 		return PTR_ERR(regmap);
 	}
 
+	desc = of_device_get_match_data(dev);
+	if (!desc)
+		return -ENODEV;
+
 	config.dev = dev;
 	config.regmap = regmap;
 
 	for (i = 0; i < MP5416_MAX_REGULATORS; i++) {
 		rdev = devm_regulator_register(dev,
-					       &mp5416_regulators_desc[i],
+					       &desc[i],
 					       &config);
 		if (IS_ERR(rdev)) {
 			dev_err(dev, "Failed to register regulator!\n");
@@ -205,13 +221,15 @@ static int mp5416_i2c_probe(struct i2c_client *client)
 }
 
 static const struct of_device_id mp5416_of_match[] = {
-	{ .compatible = "mps,mp5416" },
+	{ .compatible = "mps,mp5416", .data = &mp5416_regulators_desc },
+	{ .compatible = "mps,mp5496", .data = &mp5496_regulators_desc },
 	{},
 };
 MODULE_DEVICE_TABLE(of, mp5416_of_match);
 
 static const struct i2c_device_id mp5416_id[] = {
 	{ "mp5416", },
+	{ "mp5496", },
 	{ },
 };
 MODULE_DEVICE_TABLE(i2c, mp5416_id);

drivers/regulator/mt6370-regulator.c

+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/bits.h>
+#include <linux/gpio/consumer.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/mod_devicetable.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+
+enum {
+	MT6370_IDX_DSVBOOST = 0,
+	MT6370_IDX_DSVPOS,
+	MT6370_IDX_DSVNEG,
+	MT6370_IDX_VIBLDO,
+	MT6370_MAX_IDX
+};
+
+#define MT6370_REG_LDO_CFG	0x180
+#define MT6370_REG_LDO_VOUT	0x181
+#define MT6370_REG_DB_CTRL1	0x1B0
+#define MT6370_REG_DB_CTRL2	0x1B1
+#define MT6370_REG_DB_VBST	0x1B2
+#define MT6370_REG_DB_VPOS	0x1B3
+#define MT6370_REG_DB_VNEG	0x1B4
+#define MT6370_REG_LDO_STAT	0x1DC
+#define MT6370_REG_DB_STAT	0x1DF
+
+#define MT6370_LDOOMS_MASK	BIT(7)
+#define MT6370_LDOEN_MASK	BIT(7)
+#define MT6370_LDOVOUT_MASK	GENMASK(3, 0)
+#define MT6370_DBPERD_MASK	(BIT(7) | BIT(4))
+#define MT6370_DBEXTEN_MASK	BIT(0)
+#define MT6370_DBVPOSEN_MASK	BIT(6)
+#define MT6370_DBVPOSDISG_MASK	BIT(5)
+#define MT6370_DBVNEGEN_MASK	BIT(3)
+#define MT6370_DBVNEGDISG_MASK	BIT(2)
+#define MT6370_DBALLON_MASK	(MT6370_DBVPOSEN_MASK | MT6370_DBVNEGEN_MASK)
+#define MT6370_DBSLEW_MASK	GENMASK(7, 6)
+#define MT6370_DBVOUT_MASK	GENMASK(5, 0)
+#define MT6370_LDOOC_EVT_MASK	BIT(7)
+#define MT6370_POSSCP_EVT_MASK	BIT(7)
+#define MT6370_NEGSCP_EVT_MASK	BIT(6)
+#define MT6370_BSTOCP_EVT_MASK	BIT(5)
+#define MT6370_POSOCP_EVT_MASK	BIT(4)
+#define MT6370_NEGOCP_EVT_MASK	BIT(3)
+
+#define MT6370_LDO_MINUV	1600000
+#define MT6370_LDO_STPUV	200000
+#define MT6370_LDO_N_VOLT	13
+#define MT6370_DBVBOOST_MINUV	4000000
+#define MT6370_DBVBOOST_STPUV	50000
+#define MT6370_DBVBOOST_N_VOLT	45
+#define MT6370_DBVOUT_MINUV	4000000
+#define MT6370_DBVOUT_STPUV	50000
+#define MT6370_DBVOUT_N_VOLT	41
+
+struct mt6370_priv {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_dev *rdev[MT6370_MAX_IDX];
+	bool use_external_ctrl;
+};
+
+static const unsigned int mt6370_vpos_ramp_tbl[] = { 8540, 5840, 4830, 3000 };
+static const unsigned int mt6370_vneg_ramp_tbl[] = { 10090, 6310, 5050, 3150 };
+
+static int mt6370_get_error_flags(struct regulator_dev *rdev,
+				  unsigned int *flags)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int stat_reg, stat, rpt_flags = 0;
+	int rid = rdev_get_id(rdev), ret;
+
+	if (rid == MT6370_IDX_VIBLDO)
+		stat_reg = MT6370_REG_LDO_STAT;
+	else
+		stat_reg = MT6370_REG_DB_STAT;
+
+	ret = regmap_read(regmap, stat_reg, &stat);
+	if (ret)
+		return ret;
+
+	switch (rid) {
+	case MT6370_IDX_DSVBOOST:
+		if (stat & MT6370_BSTOCP_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_OVER_CURRENT;
+		break;
+	case MT6370_IDX_DSVPOS:
+		if (stat & MT6370_POSSCP_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_UNDER_VOLTAGE;
+
+		if (stat & MT6370_POSOCP_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_OVER_CURRENT;
+		break;
+	case MT6370_IDX_DSVNEG:
+		if (stat & MT6370_NEGSCP_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_UNDER_VOLTAGE;
+
+		if (stat & MT6370_NEGOCP_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_OVER_CURRENT;
+		break;
+	default:
+		if (stat & MT6370_LDOOC_EVT_MASK)
+			rpt_flags |= REGULATOR_ERROR_OVER_CURRENT;
+		break;
+	}
+
+	*flags = rpt_flags;
+	return 0;
+}
+
+static const struct regulator_ops mt6370_dbvboost_ops = {
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.get_bypass = regulator_get_bypass_regmap,
+	.set_bypass = regulator_set_bypass_regmap,
+	.get_error_flags = mt6370_get_error_flags,
+};
+
+static const struct regulator_ops mt6370_dbvout_ops = {
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.set_ramp_delay = regulator_set_ramp_delay_regmap,
+	.get_error_flags = mt6370_get_error_flags,
+};
+
+static const struct regulator_ops mt6370_ldo_ops = {
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.is_enabled = regulator_is_enabled_regmap,
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.get_error_flags = mt6370_get_error_flags,
+};
+
+static int mt6370_of_parse_cb(struct device_node *np,
+			      const struct regulator_desc *desc,
+			      struct regulator_config *config)
+{
+	struct mt6370_priv *priv = config->driver_data;
+	struct gpio_desc *enable_gpio;
+	int ret;
+
+	enable_gpio = fwnode_gpiod_get_index(of_fwnode_handle(np), "enable", 0,
+					     GPIOD_OUT_HIGH |
+					     GPIOD_FLAGS_BIT_NONEXCLUSIVE,
+					     desc->name);
+	if (IS_ERR(enable_gpio)) {
+		config->ena_gpiod = NULL;
+		return 0;
+	}
+
+	/*
+	 * RG control by default
+	 * Only if all are using external pin, change all by external control
+	 */
+	if (priv->use_external_ctrl) {
+		ret = regmap_update_bits(priv->regmap, MT6370_REG_DB_CTRL1,
+					 MT6370_DBEXTEN_MASK,
+					 MT6370_DBEXTEN_MASK);
+		if (ret)
+			return ret;
+	}
+
+	config->ena_gpiod = enable_gpio;
+	priv->use_external_ctrl = true;
+	return 0;
+}
+
+static const struct regulator_desc mt6370_regulator_descs[] = {
+	{
+		.name = "mt6370-dsv-vbst",
+		.of_match = of_match_ptr("dsvbst"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = MT6370_IDX_DSVBOOST,
+		.type = REGULATOR_VOLTAGE,
+		.owner = THIS_MODULE,
+		.ops = &mt6370_dbvboost_ops,
+		.min_uV = MT6370_DBVBOOST_MINUV,
+		.uV_step = MT6370_DBVBOOST_STPUV,
+		.n_voltages = MT6370_DBVBOOST_N_VOLT,
+		.vsel_reg = MT6370_REG_DB_VBST,
+		.vsel_mask = MT6370_DBVOUT_MASK,
+		.bypass_reg = MT6370_REG_DB_CTRL1,
+		.bypass_mask = MT6370_DBPERD_MASK,
+		.bypass_val_on = MT6370_DBPERD_MASK,
+	},
+	{
+		.name = "mt6370-dsv-vpos",
+		.of_match = of_match_ptr("dsvpos"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = MT6370_IDX_DSVPOS,
+		.type = REGULATOR_VOLTAGE,
+		.owner = THIS_MODULE,
+		.of_parse_cb = mt6370_of_parse_cb,
+		.ops = &mt6370_dbvout_ops,
+		.min_uV = MT6370_DBVOUT_MINUV,
+		.uV_step = MT6370_DBVOUT_STPUV,
+		.n_voltages = MT6370_DBVOUT_N_VOLT,
+		.vsel_reg = MT6370_REG_DB_VPOS,
+		.vsel_mask = MT6370_DBVOUT_MASK,
+		.enable_reg = MT6370_REG_DB_CTRL2,
+		.enable_mask = MT6370_DBVPOSEN_MASK,
+		.ramp_reg = MT6370_REG_DB_VPOS,
+		.ramp_mask = MT6370_DBSLEW_MASK,
+		.ramp_delay_table = mt6370_vpos_ramp_tbl,
+		.n_ramp_values = ARRAY_SIZE(mt6370_vpos_ramp_tbl),
+		.active_discharge_reg = MT6370_REG_DB_CTRL2,
+		.active_discharge_mask = MT6370_DBVPOSDISG_MASK,
+		.active_discharge_on = MT6370_DBVPOSDISG_MASK,
+	},
+	{
+		.name = "mt6370-dsv-vneg",
+		.of_match = of_match_ptr("dsvneg"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = MT6370_IDX_DSVNEG,
+		.type = REGULATOR_VOLTAGE,
+		.owner = THIS_MODULE,
+		.of_parse_cb = mt6370_of_parse_cb,
+		.ops = &mt6370_dbvout_ops,
+		.min_uV = MT6370_DBVOUT_MINUV,
+		.uV_step = MT6370_DBVOUT_STPUV,
+		.n_voltages = MT6370_DBVOUT_N_VOLT,
+		.vsel_reg = MT6370_REG_DB_VNEG,
+		.vsel_mask = MT6370_DBVOUT_MASK,
+		.enable_reg = MT6370_REG_DB_CTRL2,
+		.enable_mask = MT6370_DBVNEGEN_MASK,
+		.ramp_reg = MT6370_REG_DB_VNEG,
+		.ramp_mask = MT6370_DBSLEW_MASK,
+		.ramp_delay_table = mt6370_vneg_ramp_tbl,
+		.n_ramp_values = ARRAY_SIZE(mt6370_vneg_ramp_tbl),
+		.active_discharge_reg = MT6370_REG_DB_CTRL2,
+		.active_discharge_mask = MT6370_DBVNEGDISG_MASK,
+		.active_discharge_on = MT6370_DBVNEGDISG_MASK,
+	},
+	{
+		.name = "mt6370-vib-ldo",
+		.of_match = of_match_ptr("vibldo"),
+		.regulators_node = of_match_ptr("regulators"),
+		.id = MT6370_IDX_VIBLDO,
+		.type = REGULATOR_VOLTAGE,
+		.owner = THIS_MODULE,
+		.ops = &mt6370_ldo_ops,
+		.min_uV = MT6370_LDO_MINUV,
+		.uV_step = MT6370_LDO_STPUV,
+		.n_voltages = MT6370_LDO_N_VOLT,
+		.vsel_reg = MT6370_REG_LDO_VOUT,
+		.vsel_mask = MT6370_LDOVOUT_MASK,
+		.enable_reg = MT6370_REG_LDO_VOUT,
+		.enable_mask = MT6370_LDOEN_MASK,
+		.active_discharge_reg = MT6370_REG_LDO_CFG,
+		.active_discharge_mask = MT6370_LDOOMS_MASK,
+		.active_discharge_on = MT6370_LDOOMS_MASK,
+	}
+};
+
+static irqreturn_t mt6370_scp_handler(int irq, void *data)
+{
+	struct regulator_dev *rdev = data;
+
+	regulator_notifier_call_chain(rdev, REGULATOR_EVENT_UNDER_VOLTAGE,
+				      NULL);
+	return IRQ_HANDLED;
+}
+
+static irqreturn_t mt6370_ocp_handler(int irq, void *data)
+{
+	struct regulator_dev *rdev = data;
+
+	regulator_notifier_call_chain(rdev, REGULATOR_EVENT_OVER_CURRENT, NULL);
+	return IRQ_HANDLED;
+}
+
+static int mt6370_regulator_irq_register(struct mt6370_priv *priv)
+{
+	struct platform_device *pdev = to_platform_device(priv->dev);
+	static const struct {
+		const char *name;
+		int rid;
+		irq_handler_t handler;
+	} mt6370_irqs[] = {
+		{ "db_vpos_scp", MT6370_IDX_DSVPOS, mt6370_scp_handler },
+		{ "db_vneg_scp", MT6370_IDX_DSVNEG, mt6370_scp_handler },
+		{ "db_vbst_ocp", MT6370_IDX_DSVBOOST, mt6370_ocp_handler },
+		{ "db_vpos_ocp", MT6370_IDX_DSVPOS,  mt6370_ocp_handler },
+		{ "db_vneg_ocp", MT6370_IDX_DSVNEG, mt6370_ocp_handler },
+		{ "ldo_oc", MT6370_IDX_VIBLDO, mt6370_ocp_handler }
+	};
+	struct regulator_dev *rdev;
+	int i, irq, ret;
+
+	for (i = 0; i < ARRAY_SIZE(mt6370_irqs); i++) {
+		irq = platform_get_irq_byname(pdev, mt6370_irqs[i].name);
+
+		rdev = priv->rdev[mt6370_irqs[i].rid];
+
+		ret = devm_request_threaded_irq(priv->dev, irq, NULL,
+						mt6370_irqs[i].handler, 0,
+						mt6370_irqs[i].name, rdev);
+		if (ret) {
+			dev_err(priv->dev,
+				"Failed to register (%d) interrupt\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int mt6370_regualtor_register(struct mt6370_priv *priv)
+{
+	struct regulator_dev *rdev;
+	struct regulator_config cfg = {};
+	struct device *parent = priv->dev->parent;
+	int i;
+
+	cfg.dev = parent;
+	cfg.driver_data = priv;
+
+	for (i = 0; i < MT6370_MAX_IDX; i++) {
+		rdev = devm_regulator_register(priv->dev,
+					       mt6370_regulator_descs + i,
+					       &cfg);
+		if (IS_ERR(rdev)) {
+			dev_err(priv->dev,
+				"Failed to register (%d) regulator\n", i);
+			return PTR_ERR(rdev);
+		}
+
+		priv->rdev[i] = rdev;
+	}
+
+	return 0;
+}
+
+static int mt6370_regulator_probe(struct platform_device *pdev)
+{
+	struct mt6370_priv *priv;
+	int ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &pdev->dev;
+
+	priv->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!priv->regmap) {
+		dev_err(&pdev->dev, "Failed to init regmap\n");
+		return -ENODEV;
+	}
+
+	ret = mt6370_regualtor_register(priv);
+	if (ret)
+		return ret;
+
+	return mt6370_regulator_irq_register(priv);
+}
+
+static const struct platform_device_id mt6370_devid_table[] = {
+	{ "mt6370-regulator", 0},
+	{}
+};
+MODULE_DEVICE_TABLE(platform, mt6370_devid_table);
+
+static struct platform_driver mt6370_regulator_driver = {
+	.driver = {
+		.name = "mt6370-regulator",
+	},
+	.id_table = mt6370_devid_table,
+	.probe = mt6370_regulator_probe,
+};
+module_platform_driver(mt6370_regulator_driver);
+
+MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>");
+MODULE_DESCRIPTION("Mediatek MT6370 Regulator Driver");
+MODULE_LICENSE("GPL v2");

drivers/regulator/mt6380-regulator.c

@@ -319,7 +319,7 @@ static const struct platform_device_id mt6380_platform_ids[] = {
 };
 MODULE_DEVICE_TABLE(platform, mt6380_platform_ids);
 
-static const struct of_device_id mt6380_of_match[] = {
+static const struct of_device_id  __maybe_unused mt6380_of_match[] = {
 	{ .compatible = "mediatek,mt6380-regulator", },
 	{ /* sentinel */ },
 };

drivers/regulator/of_regulator.c

@@ -264,8 +264,12 @@ static int of_get_regulation_constraints(struct device *dev,
 		}
 
 		suspend_np = of_get_child_by_name(np, regulator_states[i]);
-		if (!suspend_np || !suspend_state)
+		if (!suspend_np)
 			continue;
+		if (!suspend_state) {
+			of_node_put(suspend_np);
+			continue;
+		}
 
 		if (!of_property_read_u32(suspend_np, "regulator-mode",
 					  &pval)) {

drivers/regulator/qcom_smd-regulator.c

@@ -205,6 +205,7 @@ static const struct regulator_ops rpm_mp5496_ops = {
 	.is_enabled = rpm_reg_is_enabled,
 	.list_voltage = regulator_list_voltage_linear_range,
 
+	.get_voltage = rpm_reg_get_voltage,
 	.set_voltage = rpm_reg_set_voltage,
 };
 
@@ -357,10 +358,10 @@ static const struct regulator_desc pm8941_switch = {
 
 static const struct regulator_desc pm8916_pldo = {
 	.linear_ranges = (struct linear_range[]) {
-		REGULATOR_LINEAR_RANGE(750000, 0, 208, 12500),
+		REGULATOR_LINEAR_RANGE(1750000, 0, 127, 12500),
 	},
 	.n_linear_ranges = 1,
-	.n_voltages = 209,
+	.n_voltages = 128,
 	.ops = &rpm_smps_ldo_ops,
 };
 
@@ -783,6 +784,29 @@ static const struct rpm_regulator_data rpm_pm8841_regulators[] = {
 	{}
 };
 
+static const struct rpm_regulator_data rpm_pm8909_regulators[] = {
+	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pm8916_buck_lvo_smps, "vdd_s1" },
+	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8916_buck_hvo_smps, "vdd_s2" },
+	{ "l1", QCOM_SMD_RPM_LDOA, 1, &pm8916_nldo, "vdd_l1" },
+	{ "l2", QCOM_SMD_RPM_LDOA, 2, &pm8916_nldo, "vdd_l2_l5" },
+	{ "l3", QCOM_SMD_RPM_LDOA, 3, &pm8916_nldo, "vdd_l3_l6_l10" },
+	{ "l4", QCOM_SMD_RPM_LDOA, 4, &pm8916_pldo, "vdd_l4_l7" },
+	{ "l5", QCOM_SMD_RPM_LDOA, 5, &pm8226_pldo, "vdd_l2_l5" },
+	{ "l6", QCOM_SMD_RPM_LDOA, 6, &pm8226_pldo, "vdd_l3_l6_l10" },
+	{ "l7", QCOM_SMD_RPM_LDOA, 7, &pm8226_pldo, "vdd_l4_l7" },
+	{ "l8", QCOM_SMD_RPM_LDOA, 8, &pm8916_pldo, "vdd_l8_l11_l15_l18" },
+	{ "l9", QCOM_SMD_RPM_LDOA, 9, &pm8916_pldo, "vdd_l9_l12_l14_l17" },
+	{ "l10", QCOM_SMD_RPM_LDOA, 10, &pm8916_nldo, "vdd_l3_l6_l10" },
+	{ "l11", QCOM_SMD_RPM_LDOA, 11, &pm8226_pldo, "vdd_l8_l11_l15_l18" },
+	{ "l12", QCOM_SMD_RPM_LDOA, 12, &pm8916_pldo, "vdd_l9_l12_l14_l17" },
+	{ "l13", QCOM_SMD_RPM_LDOA, 13, &pm8916_pldo, "vdd_l13" },
+	{ "l14", QCOM_SMD_RPM_LDOA, 14, &pm8916_pldo, "vdd_l9_l12_l14_l17" },
+	{ "l15", QCOM_SMD_RPM_LDOA, 15, &pm8916_pldo, "vdd_l8_l11_l15_l18" },
+	{ "l17", QCOM_SMD_RPM_LDOA, 17, &pm8916_pldo, "vdd_l9_l12_l14_l17" },
+	{ "l18", QCOM_SMD_RPM_LDOA, 18, &pm8916_pldo, "vdd_l8_l11_l15_l18" },
+	{}
+};
+
 static const struct rpm_regulator_data rpm_pm8916_regulators[] = {
 	{ "s1", QCOM_SMD_RPM_SMPA, 1, &pm8916_buck_lvo_smps, "vdd_s1" },
 	{ "s2", QCOM_SMD_RPM_SMPA, 2, &pm8916_buck_lvo_smps, "vdd_s2" },
@@ -1221,6 +1245,7 @@ static const struct rpm_regulator_data rpm_pm2250_regulators[] = {
 static const struct of_device_id rpm_of_match[] = {
 	{ .compatible = "qcom,rpm-mp5496-regulators", .data = &rpm_mp5496_regulators },
 	{ .compatible = "qcom,rpm-pm8841-regulators", .data = &rpm_pm8841_regulators },
+	{ .compatible = "qcom,rpm-pm8909-regulators", .data = &rpm_pm8909_regulators },
 	{ .compatible = "qcom,rpm-pm8916-regulators", .data = &rpm_pm8916_regulators },
 	{ .compatible = "qcom,rpm-pm8226-regulators", .data = &rpm_pm8226_regulators },
 	{ .compatible = "qcom,rpm-pm8941-regulators", .data = &rpm_pm8941_regulators },

drivers/regulator/qcom_spmi-regulator.c

@@ -164,6 +164,8 @@ enum spmi_regulator_subtype {
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL3	= 0x0f,
 	SPMI_REGULATOR_SUBTYPE_ULT_HF_CTL4	= 0x10,
 	SPMI_REGULATOR_SUBTYPE_HFS430		= 0x0a,
+	SPMI_REGULATOR_SUBTYPE_HT_P150		= 0x35,
+	SPMI_REGULATOR_SUBTYPE_HT_P600		= 0x3d,
 };
 
 enum spmi_common_regulator_registers {
@@ -544,6 +546,14 @@ static struct spmi_voltage_range hfs430_ranges[] = {
 	SPMI_VOLTAGE_RANGE(0, 320000, 320000, 2040000, 2040000, 8000),
 };
 
+static struct spmi_voltage_range ht_p150_ranges[] = {
+	SPMI_VOLTAGE_RANGE(0, 1616000, 1616000, 3304000, 3304000, 8000),
+};
+
+static struct spmi_voltage_range ht_p600_ranges[] = {
+	SPMI_VOLTAGE_RANGE(0, 1704000, 1704000, 1896000, 1896000, 8000),
+};
+
 static DEFINE_SPMI_SET_POINTS(pldo);
 static DEFINE_SPMI_SET_POINTS(nldo1);
 static DEFINE_SPMI_SET_POINTS(nldo2);
@@ -564,6 +574,8 @@ static DEFINE_SPMI_SET_POINTS(nldo660);
 static DEFINE_SPMI_SET_POINTS(ht_lvpldo);
 static DEFINE_SPMI_SET_POINTS(ht_nldo);
 static DEFINE_SPMI_SET_POINTS(hfs430);
+static DEFINE_SPMI_SET_POINTS(ht_p150);
+static DEFINE_SPMI_SET_POINTS(ht_p600);
 
 static inline int spmi_vreg_read(struct spmi_regulator *vreg, u16 addr, u8 *buf,
 				 int len)
@@ -1458,6 +1470,8 @@ static const struct regulator_ops spmi_hfs430_ops = {
 
 static const struct spmi_regulator_mapping supported_regulators[] = {
 	/*           type subtype dig_min dig_max ltype ops setpoints hpm_min */
+	SPMI_VREG(LDO,   HT_P600,  0, INF, HFS430, hfs430, ht_p600, 10000),
+	SPMI_VREG(LDO,   HT_P150,  0, INF, HFS430, hfs430, ht_p150, 10000),
 	SPMI_VREG(BUCK,  GP_CTL,   0, INF, SMPS,   smps,   smps,   100000),
 	SPMI_VREG(BUCK,  HFS430,   0, INF, HFS430, hfs430, hfs430,  10000),
 	SPMI_VREG(LDO,   N300,     0, INF, LDO,    ldo,    nldo1,   10000),
@@ -2125,6 +2139,28 @@ static const struct spmi_regulator_data pm8005_regulators[] = {
 	{ }
 };
 
+static const struct spmi_regulator_data pmp8074_regulators[] = {
+	{ "s1", 0x1400, "vdd_s1"},
+	{ "s2", 0x1700, "vdd_s2"},
+	{ "s3", 0x1a00, "vdd_s3"},
+	{ "s4", 0x1d00, "vdd_s4"},
+	{ "s5", 0x2000, "vdd_s5"},
+	{ "l1", 0x4000, "vdd_l1_l2"},
+	{ "l2", 0x4100, "vdd_l1_l2"},
+	{ "l3", 0x4200, "vdd_l3_l8"},
+	{ "l4", 0x4300, "vdd_l4"},
+	{ "l5", 0x4400, "vdd_l5_l6_l15"},
+	{ "l6", 0x4500, "vdd_l5_l6_l15"},
+	{ "l7", 0x4600, "vdd_l7"},
+	{ "l8", 0x4700, "vdd_l3_l8"},
+	{ "l9", 0x4800, "vdd_l9"},
+	/* l10 is currently unsupported HT_P50 */
+	{ "l11", 0x4a00, "vdd_l10_l11_l12_l13"},
+	{ "l12", 0x4b00, "vdd_l10_l11_l12_l13"},
+	{ "l13", 0x4c00, "vdd_l10_l11_l12_l13"},
+	{ }
+};
+
 static const struct spmi_regulator_data pms405_regulators[] = {
 	{ "s3", 0x1a00, "vdd_s3"},
 	{ }
@@ -2142,6 +2178,7 @@ static const struct of_device_id qcom_spmi_regulator_match[] = {
 	{ .compatible = "qcom,pmi8994-regulators", .data = &pmi8994_regulators },
 	{ .compatible = "qcom,pm660-regulators", .data = &pm660_regulators },
 	{ .compatible = "qcom,pm660l-regulators", .data = &pm660l_regulators },
+	{ .compatible = "qcom,pmp8074-regulators", .data = &pmp8074_regulators },
 	{ .compatible = "qcom,pms405-regulators", .data = &pms405_regulators },
 	{ }
 };

drivers/regulator/rpi-panel-attiny-regulator.c

@@ -187,15 +187,11 @@ static int attiny_update_status(struct backlight_device *bl)
 {
 	struct attiny_lcd *state = bl_get_data(bl);
 	struct regmap *regmap = state->regmap;
-	int brightness = bl->props.brightness;
+	int brightness = backlight_get_brightness(bl);
 	int ret, i;
 
 	mutex_lock(&state->lock);
 
-	if (bl->props.power != FB_BLANK_UNBLANK ||
-	    bl->props.fb_blank != FB_BLANK_UNBLANK)
-		brightness = 0;
-
 	for (i = 0; i < 10; i++) {
 		ret = regmap_write(regmap, REG_PWM, brightness);
 		if (!ret)

drivers/regulator/rt5120-regulator.c

+// SPDX-License-Identifier: GPL-2.0+
+
+#include <linux/bits.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+#include <linux/regulator/driver.h>
+#include <linux/regulator/machine.h>
+#include <linux/regulator/of_regulator.h>
+
+#define RT5120_REG_PGSTAT	0x03
+#define RT5120_REG_CH1VID	0x06
+#define RT5120_REG_CH1SLPVID	0x07
+#define RT5120_REG_ENABLE	0x08
+#define RT5120_REG_MODECTL	0x09
+#define RT5120_REG_UVOVPROT	0x0A
+#define RT5120_REG_SLPCTL	0x0C
+#define RT5120_REG_INTSTAT	0x1E
+#define RT5120_REG_DISCHG	0x1F
+
+#define RT5120_OUTPG_MASK(rid)	BIT(rid + 1)
+#define RT5120_OUTUV_MASK(rid)	BIT(rid + 9)
+#define RT5120_OUTOV_MASK(rid)	BIT(rid + 16)
+#define RT5120_CH1VID_MASK	GENMASK(6, 0)
+#define RT5120_RIDEN_MASK(rid)	BIT(rid + 1)
+#define RT5120_RADEN_MASK(rid)	BIT(rid)
+#define RT5120_FPWM_MASK(rid)	BIT(rid + 1)
+#define RT5120_UVHICCUP_MASK	BIT(1)
+#define RT5120_OVHICCUP_MASK	BIT(0)
+#define RT5120_HOTDIE_MASK	BIT(1)
+
+#define RT5120_BUCK1_MINUV	600000
+#define RT5120_BUCK1_MAXUV	1393750
+#define RT5120_BUCK1_STEPUV	6250
+#define RT5120_BUCK1_NUM_VOLT	0x80
+
+#define RT5120_AUTO_MODE	0
+#define RT5120_FPWM_MODE	1
+
+enum {
+	RT5120_REGULATOR_BUCK1 = 0,
+	RT5120_REGULATOR_BUCK2,
+	RT5120_REGULATOR_BUCK3,
+	RT5120_REGULATOR_BUCK4,
+	RT5120_REGULATOR_LDO,
+	RT5120_REGULATOR_EXTEN,
+	RT5120_MAX_REGULATOR
+};
+
+struct rt5120_priv {
+	struct device *dev;
+	struct regmap *regmap;
+	struct regulator_desc rdesc[RT5120_MAX_REGULATOR];
+};
+
+static int rt5120_buck_set_mode(struct regulator_dev *rdev, unsigned int mode)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int rid = rdev_get_id(rdev);
+	unsigned int mask = RT5120_FPWM_MASK(rid), val;
+
+	switch (mode) {
+	case REGULATOR_MODE_NORMAL:
+		val = 0;
+		break;
+	case REGULATOR_MODE_FAST:
+		val = RT5120_FPWM_MASK(rid);
+		break;
+	default:
+		return -EINVAL;
+	}
+
+	return regmap_update_bits(regmap, RT5120_REG_MODECTL, mask, val);
+}
+
+static unsigned int rt5120_buck_get_mode(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int ret, rid = rdev_get_id(rdev);
+	unsigned int val;
+
+	ret = regmap_read(regmap, RT5120_REG_MODECTL, &val);
+	if (ret)
+		return REGULATOR_MODE_INVALID;
+
+	if (val & RT5120_FPWM_MASK(rid))
+		return REGULATOR_MODE_FAST;
+
+	return REGULATOR_MODE_NORMAL;
+}
+
+static int rt5120_regulator_get_error_flags(struct regulator_dev *rdev,
+					    unsigned int *flags)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	unsigned int stat, hd_stat, cur_flags = 0;
+	int rid = rdev_get_id(rdev), ret;
+
+	/*
+	 * reg 0x03/0x04/0x05 to indicate PG/UV/OV
+	 * use block read to descrease I/O xfer time
+	 */
+	ret = regmap_raw_read(regmap, RT5120_REG_PGSTAT, &stat, 3);
+	if (ret)
+		return ret;
+
+	ret = regmap_read(regmap, RT5120_REG_INTSTAT, &hd_stat);
+	if (ret)
+		return ret;
+
+	if (!(stat & RT5120_OUTPG_MASK(rid))) {
+		if (stat & RT5120_OUTUV_MASK(rid))
+			cur_flags |= REGULATOR_ERROR_UNDER_VOLTAGE;
+
+		if (stat & RT5120_OUTOV_MASK(rid))
+			cur_flags |= REGULATOR_ERROR_REGULATION_OUT;
+	}
+
+	if (hd_stat & RT5120_HOTDIE_MASK)
+		cur_flags |= REGULATOR_ERROR_OVER_TEMP;
+
+	*flags = cur_flags;
+	return 0;
+}
+
+static int rt5120_buck1_set_suspend_voltage(struct regulator_dev *rdev, int uV)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int sel;
+
+	if (uV < RT5120_BUCK1_MINUV || uV > RT5120_BUCK1_MAXUV)
+		return -EINVAL;
+
+	sel = (uV - RT5120_BUCK1_MINUV) / RT5120_BUCK1_STEPUV;
+	return regmap_write(regmap, RT5120_REG_CH1SLPVID, sel);
+}
+
+static int rt5120_regulator_set_suspend_enable(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int rid = rdev_get_id(rdev);
+	unsigned int mask = RT5120_RIDEN_MASK(rid);
+
+	return regmap_update_bits(regmap, RT5120_REG_SLPCTL, mask, mask);
+}
+
+static int rt5120_regulator_set_suspend_disable(struct regulator_dev *rdev)
+{
+	struct regmap *regmap = rdev_get_regmap(rdev);
+	int rid = rdev_get_id(rdev);
+	unsigned int mask = RT5120_RIDEN_MASK(rid);
+
+	return regmap_update_bits(regmap, RT5120_REG_SLPCTL, mask, 0);
+}
+
+static const struct regulator_ops rt5120_buck1_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.list_voltage = regulator_list_voltage_linear,
+	.set_voltage_sel = regulator_set_voltage_sel_regmap,
+	.get_voltage_sel = regulator_get_voltage_sel_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.set_mode = rt5120_buck_set_mode,
+	.get_mode = rt5120_buck_get_mode,
+	.get_error_flags = rt5120_regulator_get_error_flags,
+	.set_suspend_voltage = rt5120_buck1_set_suspend_voltage,
+	.set_suspend_enable = rt5120_regulator_set_suspend_enable,
+	.set_suspend_disable = rt5120_regulator_set_suspend_disable,
+};
+
+static const struct regulator_ops rt5120_buck234_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.set_mode = rt5120_buck_set_mode,
+	.get_mode = rt5120_buck_get_mode,
+	.get_error_flags = rt5120_regulator_get_error_flags,
+	.set_suspend_enable = rt5120_regulator_set_suspend_enable,
+	.set_suspend_disable = rt5120_regulator_set_suspend_disable,
+};
+
+static const struct regulator_ops rt5120_ldo_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_active_discharge = regulator_set_active_discharge_regmap,
+	.get_error_flags = rt5120_regulator_get_error_flags,
+	.set_suspend_enable = rt5120_regulator_set_suspend_enable,
+	.set_suspend_disable = rt5120_regulator_set_suspend_disable,
+};
+
+static const struct regulator_ops rt5120_exten_ops = {
+	.enable = regulator_enable_regmap,
+	.disable = regulator_disable_regmap,
+	.is_enabled = regulator_is_enabled_regmap,
+	.set_suspend_enable = rt5120_regulator_set_suspend_enable,
+	.set_suspend_disable = rt5120_regulator_set_suspend_disable,
+};
+
+static unsigned int rt5120_buck_of_map_mode(unsigned int mode)
+{
+	switch (mode) {
+	case RT5120_AUTO_MODE:
+		return REGULATOR_MODE_NORMAL;
+	case RT5120_FPWM_MODE:
+		return REGULATOR_MODE_FAST;
+	default:
+		return REGULATOR_MODE_INVALID;
+	}
+}
+
+static void rt5120_fillin_regulator_desc(struct regulator_desc *desc, int rid)
+{
+	static const char * const name[] = {
+		"buck1", "buck2", "buck3", "buck4", "ldo", "exten" };
+	static const char * const sname[] = {
+		"vin1", "vin2", "vin3", "vin4", "vinldo", NULL };
+
+	/* Common regulator property */
+	desc->name = name[rid];
+	desc->supply_name = sname[rid];
+	desc->owner = THIS_MODULE;
+	desc->type = REGULATOR_VOLTAGE;
+	desc->id = rid;
+	desc->enable_reg = RT5120_REG_ENABLE;
+	desc->enable_mask = RT5120_RIDEN_MASK(rid);
+	desc->active_discharge_reg = RT5120_REG_DISCHG;
+	desc->active_discharge_mask = RT5120_RADEN_MASK(rid);
+	desc->active_discharge_on = RT5120_RADEN_MASK(rid);
+	/* Config n_voltages to 1 for all*/
+	desc->n_voltages = 1;
+
+	/* Only buck support mode change */
+	if (rid >= RT5120_REGULATOR_BUCK1 && rid <= RT5120_REGULATOR_BUCK4)
+		desc->of_map_mode = rt5120_buck_of_map_mode;
+
+	/* RID specific property init */
+	switch (rid) {
+	case RT5120_REGULATOR_BUCK1:
+		/* Only buck1 support voltage change by I2C */
+		desc->n_voltages = RT5120_BUCK1_NUM_VOLT;
+		desc->min_uV = RT5120_BUCK1_MINUV;
+		desc->uV_step = RT5120_BUCK1_STEPUV;
+		desc->vsel_reg = RT5120_REG_CH1VID,
+		desc->vsel_mask = RT5120_CH1VID_MASK,
+		desc->ops = &rt5120_buck1_ops;
+		break;
+	case RT5120_REGULATOR_BUCK2 ... RT5120_REGULATOR_BUCK4:
+		desc->ops = &rt5120_buck234_ops;
+		break;
+	case RT5120_REGULATOR_LDO:
+		desc->ops = &rt5120_ldo_ops;
+		break;
+	default:
+		desc->ops = &rt5120_exten_ops;
+	}
+}
+
+static int rt5120_of_parse_cb(struct rt5120_priv *priv, int rid,
+			      struct of_regulator_match *match)
+{
+	struct regulator_desc *desc = priv->rdesc + rid;
+	struct regulator_init_data *init_data = match->init_data;
+
+	if (!init_data || rid == RT5120_REGULATOR_BUCK1)
+		return 0;
+
+	if (init_data->constraints.min_uV != init_data->constraints.max_uV) {
+		dev_err(priv->dev, "Variable voltage for fixed regulator\n");
+		return -EINVAL;
+	}
+
+	desc->fixed_uV = init_data->constraints.min_uV;
+	return 0;
+}
+
+static struct of_regulator_match rt5120_regu_match[RT5120_MAX_REGULATOR] = {
+	[RT5120_REGULATOR_BUCK1] = { .name = "buck1", },
+	[RT5120_REGULATOR_BUCK2] = { .name = "buck2", },
+	[RT5120_REGULATOR_BUCK3] = { .name = "buck3", },
+	[RT5120_REGULATOR_BUCK4] = { .name = "buck4", },
+	[RT5120_REGULATOR_LDO] = { .name = "ldo", },
+	[RT5120_REGULATOR_EXTEN] = { .name = "exten", }
+};
+
+static int rt5120_parse_regulator_dt_data(struct rt5120_priv *priv)
+{
+	struct device *dev = priv->dev->parent;
+	struct device_node *reg_node;
+	int i, ret;
+
+	for (i = 0; i < RT5120_MAX_REGULATOR; i++) {
+		rt5120_fillin_regulator_desc(priv->rdesc + i, i);
+
+		rt5120_regu_match[i].desc = priv->rdesc + i;
+	}
+
+	reg_node = of_get_child_by_name(dev->of_node, "regulators");
+	if (!reg_node) {
+		dev_err(priv->dev, "Couldn't find 'regulators' node\n");
+		return -ENODEV;
+	}
+
+	ret = of_regulator_match(priv->dev, reg_node, rt5120_regu_match,
+				 ARRAY_SIZE(rt5120_regu_match));
+
+	of_node_put(reg_node);
+
+	if (ret < 0) {
+		dev_err(priv->dev,
+			"Error parsing regulator init data (%d)\n", ret);
+		return ret;
+	}
+
+	for (i = 0; i < RT5120_MAX_REGULATOR; i++) {
+		ret = rt5120_of_parse_cb(priv, i, rt5120_regu_match + i);
+		if (ret) {
+			dev_err(priv->dev, "Failed in [%d] of_passe_cb\n", i);
+			return ret;
+		}
+	}
+
+	return 0;
+}
+
+static int rt5120_device_property_init(struct rt5120_priv *priv)
+{
+	struct device *dev = priv->dev->parent;
+	struct device_node *np = dev->of_node;
+	bool prot_enable;
+	unsigned int prot_enable_val = 0;
+
+	/* Assign UV/OV HW protection behavior */
+	prot_enable = of_property_read_bool(np,
+					    "richtek,enable-undervolt-hiccup");
+	if (prot_enable)
+		prot_enable_val |= RT5120_UVHICCUP_MASK;
+
+	prot_enable = of_property_read_bool(np,
+					    "richtek,enable-overvolt-hiccup");
+	if (prot_enable)
+		prot_enable_val |= RT5120_OVHICCUP_MASK;
+
+	return regmap_update_bits(priv->regmap, RT5120_REG_UVOVPROT,
+				  RT5120_UVHICCUP_MASK | RT5120_OVHICCUP_MASK,
+				  prot_enable_val);
+}
+
+static int rt5120_regulator_probe(struct platform_device *pdev)
+{
+	struct rt5120_priv *priv;
+	struct regulator_dev *rdev;
+	struct regulator_config config = {};
+	int i, ret;
+
+	priv = devm_kzalloc(&pdev->dev, sizeof(*priv), GFP_KERNEL);
+	if (!priv)
+		return -ENOMEM;
+
+	priv->dev = &pdev->dev;
+
+	priv->regmap = dev_get_regmap(pdev->dev.parent, NULL);
+	if (!priv->regmap) {
+		dev_err(&pdev->dev, "Failed to init regmap\n");
+		return -ENODEV;
+	}
+
+	ret = rt5120_device_property_init(priv);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to do property init\n");
+		return ret;
+	}
+
+	ret = rt5120_parse_regulator_dt_data(priv);
+	if (ret) {
+		dev_err(&pdev->dev, "Failed to parse dt data\n");
+		return ret;
+	}
+
+	config.dev = &pdev->dev;
+	config.regmap = priv->regmap;
+
+	for (i = 0; i < RT5120_MAX_REGULATOR; i++) {
+		config.of_node = rt5120_regu_match[i].of_node;
+		config.init_data = rt5120_regu_match[i].init_data;
+
+		rdev = devm_regulator_register(&pdev->dev, priv->rdesc + i,
+					       &config);
+		if (IS_ERR(rdev)) {
+			dev_err(&pdev->dev,
+				"Failed to register regulator [%d]\n", i);
+			return PTR_ERR(rdev);
+		}
+	}
+
+	return 0;
+}
+
+static const struct platform_device_id rt5120_regulator_dev_table[] = {
+	{ "rt5120-regulator", 0 },
+	{}
+};
+MODULE_DEVICE_TABLE(platform, rt5120_regulator_dev_table);
+
+static struct platform_driver rt5120_regulator_driver = {
+	.driver = {
+		.name = "rt5120-regulator",
+	},
+	.id_table = rt5120_regulator_dev_table,
+	.probe = rt5120_regulator_probe,
+};
+module_platform_driver(rt5120_regulator_driver);
+
+MODULE_AUTHOR("ChiYuan Huang <cy_huang@richtek.com>");
+MODULE_DESCRIPTION("Richtek RT5120 regulator driver");
+MODULE_LICENSE("GPL v2");

drivers/regulator/rt5190a-regulator.c

@@ -224,6 +224,9 @@ static int rt5190a_of_parse_cb(struct rt5190a_priv *priv, int rid,
 	bool latchup_enable;
 	unsigned int mask = RT5190A_RID_BITMASK(rid), val;
 
+	if (!init_data)
+		return 0;
+
 	switch (rid) {
 	case RT5190A_IDX_BUCK1:
 	case RT5190A_IDX_BUCK4:

drivers/regulator/scmi-regulator.c

@@ -343,6 +343,7 @@ static int scmi_regulator_probe(struct scmi_device *sdev)
 	 * plausible SCMI Voltage Domain number, all belonging to this SCMI
 	 * platform instance node (handle->dev->of_node).
 	 */
+	of_node_get(handle->dev->of_node);
 	np = of_find_node_by_name(handle->dev->of_node, "regulators");
 	for_each_child_of_node(np, child) {
 		ret = process_scmi_regulator_of_node(sdev, ph, child, rinfo);

drivers/regulator/ti-abb-regulator.c

@@ -309,7 +309,7 @@ static int ti_abb_set_opp(struct regulator_dev *rdev, struct ti_abb *abb,
  *
  * Return: 0 on success or appropriate error value when fails
  */
-static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned sel)
+static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned int sel)
 {
 	const struct regulator_desc *desc = rdev->desc;
 	struct ti_abb *abb = rdev_get_drvdata(rdev);
@@ -344,7 +344,7 @@ static int ti_abb_set_voltage_sel(struct regulator_dev *rdev, unsigned sel)
 
 	info = &abb->info[sel];
 	/*
-	 * When Linux kernel is starting up, we are'nt sure of the
+	 * When Linux kernel is starting up, we aren't sure of the
 	 * Bias configuration that bootloader has configured.
 	 * So, we get to know the actual setting the first time
 	 * we are asked to transition.

include/linux/regulator/consumer.h

@@ -173,6 +173,9 @@ struct regulator;
  *
  * @supply:       The name of the supply.  Initialised by the user before
  *                using the bulk regulator APIs.
+ * @init_load_uA: After getting the regulator, regulator_set_load() will be
+ *                called with this load.  Initialised by the user before
+ *                using the bulk regulator APIs.
  * @consumer:     The regulator consumer for the supply.  This will be managed
  *                by the bulk API.
  *
@@ -182,6 +185,7 @@ struct regulator;
  */
 struct regulator_bulk_data {
 	const char *supply;
+	int init_load_uA;
 	struct regulator *consumer;
 
 	/* private: Internal use */
@@ -240,6 +244,10 @@ int __must_check regulator_bulk_get(struct device *dev, int num_consumers,
 				    struct regulator_bulk_data *consumers);
 int __must_check devm_regulator_bulk_get(struct device *dev, int num_consumers,
 					 struct regulator_bulk_data *consumers);
+int __must_check devm_regulator_bulk_get_const(
+	struct device *dev, int num_consumers,
+	const struct regulator_bulk_data *in_consumers,
+	struct regulator_bulk_data **out_consumers);
 int __must_check regulator_bulk_enable(int num_consumers,
 				       struct regulator_bulk_data *consumers);
 int regulator_bulk_disable(int num_consumers,

include/linux/regulator/driver.h

@@ -348,6 +348,7 @@ enum regulator_type {
  * @ramp_delay_table:	Table for mapping the regulator ramp-rate values. Values
  *			should be given in units of V/S (uV/uS). See the
  *			regulator_set_ramp_delay_regmap().
+ * @n_ramp_values:	number of elements at @ramp_delay_table.
  *
  * @enable_time: Time taken for initial enable of regulator (in uS).
  * @off_on_delay: guard time (in uS), before re-enabling a regulator