Merge tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC driver updates from Olof Johansson:
 "Driver updates for ARM SoCs.

  A slew of changes this release cycle.  The reset driver tree, that we
  merge through arm-soc for historical reasons, is also sizable this
  time around.

  Among the changes:

   - clps711x: Treewide changes to compatible strings, merged here for simplicity.
   - Qualcomm: SCM firmware driver cleanups, move to platform driver
   - ux500: Major cleanups, removal of old mach-specific infrastructure.
   - Atmel external bus memory driver
   - Move of brcmstb platform to the rest of bcm
   - PMC driver updates for tegra, various fixes and improvements
   - Samsung platform driver updates to support 64-bit Exynos platforms
   - Reset controller cleanups moving to devm_reset_controller_register() APIs
   - Reset controller driver for Amlogic Meson
   - Reset controller driver for Hisilicon hi6220
   - ARM SCPI power domain support"

* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
  ARM: ux500: consolidate base platform files
  ARM: ux500: move soc_id driver to drivers/soc
  ARM: ux500: call ux500_setup_id later
  ARM: ux500: consolidate soc_device code in id.c
  ARM: ux500: remove cpu_is_u* helpers
  ARM: ux500: use CLK_OF_DECLARE()
  ARM: ux500: move l2x0 init to .init_irq
  mfd: db8500 stop passing around platform data
  ASoC: ab8500-codec: remove platform data based probe
  ARM: ux500: move ab8500_regulator_plat_data into driver
  ARM: ux500: remove unused regulator data
  soc: raspberrypi-power: add CONFIG_OF dependency
  firmware: scpi: add CONFIG_OF dependency
  video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
  input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
  pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
  serial: clps711x: Changing the compatibility string to match with the smallest supported chip
  irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
  clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
  clk: clps711x: Changing the compatibility string to match with the smallest supported chip
  ...

Documentation/devicetree/bindings/arm/arm,scpi.txt

@@ -87,10 +87,33 @@ Required properties:
 			 implementation for the IDs to use. For Juno
 			 R0 and Juno R1 refer to [3].
 
+Power domain bindings for the power domains based on SCPI Message Protocol
+------------------------------------------------------------
+
+This binding uses the generic power domain binding[4].
+
+PM domain providers
+===================
+
+Required properties:
+ - #power-domain-cells : Should be 1. Contains the device or the power
+			 domain ID value used by SCPI commands.
+ - num-domains: Total number of power domains provided by SCPI. This is
+		needed as the SCPI message protocol lacks a mechanism to
+		query this information at runtime.
+
+PM domain consumers
+===================
+
+Required properties:
+ - power-domains : A phandle and PM domain specifier as defined by bindings of
+                   the power controller specified by phandle.
+
 [0] http://infocenter.arm.com/help/topic/com.arm.doc.dui0922b/index.html
 [1] Documentation/devicetree/bindings/clock/clock-bindings.txt
 [2] Documentation/devicetree/bindings/thermal/thermal.txt
 [3] http://infocenter.arm.com/help/index.jsp?topic=/com.arm.doc.dui0922b/apas03s22.html
+[4] Documentation/devicetree/bindings/power/power_domain.txt
 
 Example:
 
@@ -144,6 +167,12 @@ scpi_protocol: scpi@2e000000 {
 		compatible = "arm,scpi-sensors";
 		#thermal-sensor-cells = <1>;
 	};
+
+	scpi_devpd: scpi-power-domains {
+		compatible = "arm,scpi-power-domains";
+		num-domains = <2>;
+		#power-domain-cells = <1>;
+	};
 };
 
 cpu@0 {
@@ -156,6 +185,7 @@ hdlcd@7ff60000 {
 	...
 	reg = <0 0x7ff60000 0 0x1000>;
 	clocks = <&scpi_clk 4>;
+	power-domains = <&scpi_devpd 1>;
 };
 
 thermal-zones {
@@ -186,3 +216,7 @@ The thermal-sensors property in the soc_thermal node uses the
 temperature sensor provided by SCP firmware to setup a thermal
 zone. The ID "3" is the sensor identifier for the temperature sensor
 as used by the firmware.
+
+The num-domains property in scpi-power-domains domain specifies that
+SCPI provides 2 power domains. The hdlcd node uses the power domain with
+domain ID 1.

Documentation/devicetree/bindings/bus/nvidia,tegra210-aconnect.txt

+NVIDIA Tegra ACONNECT Bus
+
+The Tegra ACONNECT bus is an AXI switch which is used to connnect various
+components inside the Audio Processing Engine (APE). All CPU accesses to
+the APE subsystem go through the ACONNECT via an APB to AXI wrapper.
+
+Required properties:
+- compatible: Must be "nvidia,tegra210-aconnect".
+- clocks: Must contain the entries for the APE clock (TEGRA210_CLK_APE),
+  and APE interface clock (TEGRA210_CLK_APB2APE).
+- clock-names: Must contain the names "ape" and "apb2ape" for the corresponding
+  'clocks' entries.
+- power-domains: Must contain a phandle that points to the audio powergate
+  (namely 'aud') for Tegra210.
+- #address-cells: The number of cells used to represent physical base addresses
+  in the aconnect address space. Should be 1.
+- #size-cells: The number of cells used to represent the size of an address
+  range in the aconnect address space. Should be 1.
+- ranges: Mapping of the aconnect address space to the CPU address space.
+
+All devices accessed via the ACONNNECT are described by child-nodes.
+
+Example:
+
+	aconnect@702c0000 {
+		compatible = "nvidia,tegra210-aconnect";
+		clocks = <&tegra_car TEGRA210_CLK_APE>,
+			 <&tegra_car TEGRA210_CLK_APB2APE>;
+		clock-names = "ape", "apb2ape";
+		power-domains = <&pd_audio>;
+
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges = <0x702c0000 0x0 0x702c0000 0x00040000>;
+
+		status = "disabled";
+
+		child1 {
+			...
+		};
+
+		child2 {
+			...
+		};
+	};

Documentation/devicetree/bindings/clock/clps711x-clock.txt

 * Clock bindings for the Cirrus Logic CLPS711X CPUs
 
 Required properties:
-- compatible       : Shall contain "cirrus,clps711x-clk".
+- compatible       : Shall contain "cirrus,ep7209-clk".
 - reg              : Address of the internal register set.
 - startup-frequency: Factory set CPU startup frequency in HZ.
 - #clock-cells     : Should be <1>.
@@ -13,7 +13,7 @@ for the full list of CLPS711X clock IDs.
 Example:
 	clks: clks@80000000 {
 		#clock-cells = <1>;
-		compatible = "cirrus,ep7312-clk", "cirrus,clps711x-clk";
+		compatible = "cirrus,ep7312-clk", "cirrus,ep7209-clk";
 		reg = <0x80000000 0xc000>;
 		startup-frequency = <73728000>;
 	};

Documentation/devicetree/bindings/display/cirrus,clps711x-fb.txt

 * Currus Logic CLPS711X Framebuffer
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-fb".
+- compatible: Shall contain "cirrus,ep7209-fb".
 - reg       : Physical base address and length of the controller's registers +
               location and size of the framebuffer memory.
 - clocks    : phandle + clock specifier pair of the FB reference clock.
@@ -18,7 +18,7 @@ Optional properties:
 
 Example:
 	fb: fb@800002c0 {
-		compatible = "cirrus,ep7312-fb", "cirrus,clps711x-fb";
+		compatible = "cirrus,ep7312-fb", "cirrus,ep7209-fb";
 		reg = <0x800002c0 0xd44>, <0x60000000 0xc000>;
 		clocks = <&clks 2>;
 		lcd-supply = <&reg5v0>;

Documentation/devicetree/bindings/input/clps711x-keypad.txt

 * Cirrus Logic CLPS711X matrix keypad device tree bindings
 
 Required Properties:
-- compatible:    Shall contain "cirrus,clps711x-keypad".
+- compatible:    Shall contain "cirrus,ep7209-keypad".
 - row-gpios:     List of GPIOs used as row lines.
 - poll-interval: Poll interval time in milliseconds.
 - linux,keymap:  The definition can be found at
@@ -12,7 +12,7 @@ Optional Properties:
 
 Example:
 	keypad {
-		compatible = "cirrus,ep7312-keypad", "cirrus,clps711x-keypad";
+		compatible = "cirrus,ep7312-keypad", "cirrus,ep7209-keypad";
 		autorepeat;
 		poll-interval = <120>;
 		row-gpios = <&porta 0 0>,

Documentation/devicetree/bindings/interrupt-controller/cirrus,clps711x-intc.txt

@@ -2,7 +2,7 @@ Cirrus Logic CLPS711X Interrupt Controller
 
 Required properties:
 
-- compatible: Should be "cirrus,clps711x-intc".
+- compatible: Should be "cirrus,ep7209-intc".
 - reg: Specifies base physical address of the registers set.
 - interrupt-controller: Identifies the node as an interrupt controller.
 - #interrupt-cells: Specifies the number of cells needed to encode an
@@ -34,7 +34,7 @@ ID	Name	Description
 
 Example:
 	intc: interrupt-controller {
-		compatible = "cirrus,clps711x-intc";
+		compatible = "cirrus,ep7312-intc", "cirrus,ep7209-intc";
 		reg = <0x80000000 0x4000>;
 		interrupt-controller;
 		#interrupt-cells = <1>;

Documentation/devicetree/bindings/media/nokia,n900-ir

+Device-Tree bindings for LIRC TX driver for Nokia N900(RX51)
+
+Required properties:
+	- compatible: should be "nokia,n900-ir".
+	- pwms: specifies PWM used for IR signal transmission.
+
+Example node:
+
+	pwm9: dmtimer-pwm@9 {
+		compatible = "ti,omap-dmtimer-pwm";
+		ti,timers = <&timer9>;
+		ti,clock-source = <0x00>; /* timer_sys_ck */
+		#pwm-cells = <3>;
+	};
+
+	ir: n900-ir {
+		compatible = "nokia,n900-ir";
+
+		pwms = <&pwm9 0 26316 0>; /* 38000 Hz */
+	};

Documentation/devicetree/bindings/memory-controllers/atmel,ebi.txt

+* Device tree bindings for Atmel EBI
+
+The External Bus Interface (EBI) controller is a bus where you can connect
+asynchronous (NAND, NOR, SRAM, ....) and synchronous memories (SDR/DDR SDRAMs).
+The EBI provides a glue-less interface to asynchronous memories through the SMC
+(Static Memory Controller).
+
+Required properties:
+
+- compatible:		"atmel,at91sam9260-ebi"
+			"atmel,at91sam9261-ebi"
+			"atmel,at91sam9263-ebi0"
+			"atmel,at91sam9263-ebi1"
+			"atmel,at91sam9rl-ebi"
+			"atmel,at91sam9g45-ebi"
+			"atmel,at91sam9x5-ebi"
+			"atmel,sama5d3-ebi"
+
+- reg:			Contains offset/length value for EBI memory mapping.
+			This property might contain several entries if the EBI
+			memory range is not contiguous
+
+- #address-cells:	Must be 2.
+			The first cell encodes the CS.
+			The second cell encode the offset into the CS memory
+			range.
+
+- #size-cells:		Must be set to 1.
+
+- ranges:		Encodes CS to memory region association.
+
+- clocks:		Clock feeding the EBI controller.
+			See clock-bindings.txt
+
+Children device nodes are representing device connected to the EBI bus.
+
+Required device node properties:
+
+- reg:			Contains the chip-select id, the offset and the length
+			of the memory region requested by the device.
+
+EBI bus configuration will be defined directly in the device subnode.
+
+Optional EBI/SMC properties:
+
+- atmel,smc-bus-width:		width of the asynchronous device's data bus
+				8, 16 or 32.
+				Default to 8 when undefined.
+
+- atmel,smc-byte-access-type	"write" or "select" (see Atmel datasheet).
+				Default to "select" when undefined.
+
+- atmel,smc-read-mode		"nrd" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-write-mode		"nwe" or "ncs".
+				Default to "ncs" when undefined.
+
+- atmel,smc-exnw-mode		"disabled", "frozen" or "ready".
+				Default to "disabled" when undefined.
+
+- atmel,smc-page-mode		enable page mode if present. The provided value
+				defines the page size (supported values: 4, 8,
+				16 and 32).
+
+- atmel,smc-tdf-mode:		"normal" or "optimized". When set to
+				"optimized" the data float time is optimized
+				depending on the next device being accessed
+				(next device setup time is subtracted to the
+				current device data float time).
+				Default to "normal" when undefined.
+
+If at least one atmel,smc- property is defined the following SMC timing
+properties become mandatory. In the other hand, if none of the atmel,smc-
+properties are specified, we assume that the EBI bus configuration will be
+handled by the sub-device driver, and none of those properties should be
+defined.
+
+All the timings are expressed in nanoseconds (see Atmel datasheet for a full
+description).
+
+- atmel,smc-ncs-rd-setup-ns
+- atmel,smc-nrd-setup-ns
+- atmel,smc-ncs-wr-setup-ns
+- atmel,smc-nwe-setup-ns
+- atmel,smc-ncs-rd-pulse-ns
+- atmel,smc-nrd-pulse-ns
+- atmel,smc-ncs-wr-pulse-ns
+- atmel,smc-nwe-pulse-ns
+- atmel,smc-nwe-cycle-ns
+- atmel,smc-nrd-cycle-ns
+- atmel,smc-tdf-ns
+
+Example:
+
+	ebi: ebi@10000000 {
+		compatible = "atmel,sama5d3-ebi";
+		#address-cells = <2>;
+		#size-cells = <1>;
+		atmel,smc = <&hsmc>;
+		atmel,matrix = <&matrix>;
+		reg = <0x10000000 0x10000000
+		       0x40000000 0x30000000>;
+		ranges = <0x0 0x0 0x10000000 0x10000000
+			  0x1 0x0 0x40000000 0x10000000
+			  0x2 0x0 0x50000000 0x10000000
+			  0x3 0x0 0x60000000 0x10000000>;
+		clocks = <&mck>;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_ebi_addr>;
+
+		nor: flash@0,0 {
+			compatible = "cfi-flash";
+			#address-cells = <1>;
+			#size-cells = <1>;
+			reg = <0x0 0x0 0x1000000>;
+			bank-width = <2>;
+
+			atmel,smc-read-mode = "nrd";
+			atmel,smc-write-mode = "nwe";
+			atmel,smc-bus-width = <16>;
+			atmel,smc-ncs-rd-setup-ns = <0>;
+			atmel,smc-ncs-wr-setup-ns = <0>;
+			atmel,smc-nwe-setup-ns = <8>;
+			atmel,smc-nrd-setup-ns = <16>;
+			atmel,smc-ncs-rd-pulse-ns = <84>;
+			atmel,smc-ncs-wr-pulse-ns = <84>;
+			atmel,smc-nrd-pulse-ns = <76>;
+			atmel,smc-nwe-pulse-ns = <76>;
+			atmel,smc-nrd-cycle-ns = <107>;
+			atmel,smc-nwe-cycle-ns = <84>;
+			atmel,smc-tdf-ns = <16>;
+		};
+	};
+

Documentation/devicetree/bindings/pwm/cirrus,clps711x-pwm.txt

 * Cirris Logic CLPS711X PWM controller
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-pwm".
+- compatible: Shall contain "cirrus,ep7209-pwm".
 - reg: Physical base address and length of the controller's registers.
 - clocks: phandle + clock specifier pair of the PWM reference clock.
 - #pwm-cells: Should be 1. The cell specifies the index of the channel.
 
 Example:
 	pwm: pwm@80000400 {
-		compatible = "cirrus,ep7312-pwm",
-			     "cirrus,clps711x-pwm";
+		compatible = "cirrus,ep7312-pwm", "cirrus,ep7209-pwm";
 		reg = <0x80000400 0x4>;
 		clocks = <&clks 8>;
 		#pwm-cells = <1>;

Documentation/devicetree/bindings/pwm/pwm-omap-dmtimer.txt

@@ -9,6 +9,10 @@ Required properties:
 
 Optional properties:
 - ti,prescaler: Should be a value between 0 and 7, see the timers datasheet
+- ti,clock-source: Set dmtimer parent clock, values between 0 and 2:
+  - 0x00 - high-frequency system clock (timer_sys_ck)
+  - 0x01 - 32-kHz always-on clock (timer_32k_ck)
+  - 0x02 - external clock (timer_ext_ck, OMAP2 only)
 
 Example:
 	pwm9: dmtimer-pwm@9 {

Documentation/devicetree/bindings/reset/amlogic,meson-reset.txt

+Amlogic Meson SoC Reset Controller
+=======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+- compatible: Should be "amlogic,meson8b-reset" or "amlogic,meson-gxbb-reset"
+- reg: should contain the register address base
+- #reset-cells: 1, see below
+
+example:
+
+reset: reset-controller {
+	compatible = "amlogic,meson-gxbb-reset";
+	reg = <0x0 0x04404 0x0 0x20>;
+	#reset-cells = <1>;
+};

Documentation/devicetree/bindings/reset/hisilicon,hi6220-reset.txt

@@ -8,7 +8,9 @@ The reset controller registers are part of the system-ctl block on
 hi6220 SoC.
 
 Required properties:
-- compatible: may be "hisilicon,hi6220-sysctrl"
+- compatible: should be one of the following:
+  - "hisilicon,hi6220-sysctrl", "syscon" : For peripheral reset controller.
+  - "hisilicon,hi6220-mediactrl", "syscon" : For media reset controller.
 - reg: should be register base and length as documented in the
   datasheet
 - #reset-cells: 1, see below

Documentation/devicetree/bindings/reset/ti-syscon-reset.txt

+TI SysCon Reset Controller
+=======================
+
+Almost all SoCs have hardware modules that require reset control in addition
+to clock and power control for their functionality. The reset control is
+typically provided by means of memory-mapped I/O registers. These registers are
+sometimes a part of a larger register space region implementing various
+functionalities. This register range is best represented as a syscon node to
+allow multiple entities to access their relevant registers in the common
+register space.
+
+A SysCon Reset Controller node defines a device that uses a syscon node
+and provides reset management functionality for various hardware modules
+present on the SoC.
+
+SysCon Reset Controller Node
+============================
+Each of the reset provider/controller nodes should be a child of a syscon
+node and have the following properties.
+
+Required properties:
+--------------------
+ - compatible		: Should be,
+			    "ti,k2e-pscrst"
+			    "ti,k2l-pscrst"
+			    "ti,k2hk-pscrst"
+			    "ti,syscon-reset"
+ - #reset-cells		: Should be 1. Please see the reset consumer node below
+			  for usage details
+ - ti,reset-bits	: Contains the reset control register information
+			  Should contain 7 cells for each reset exposed to
+			  consumers, defined as:
+			    Cell #1 : offset of the reset assert control
+			              register from the syscon register base
+			    Cell #2 : bit position of the reset in the reset
+			              assert control register
+			    Cell #3 : offset of the reset deassert control
+			              register from the syscon register base
+			    Cell #4 : bit position of the reset in the reset
+			              deassert control register
+			    Cell #5 : offset of the reset status register
+			              from the syscon register base
+			    Cell #6 : bit position of the reset in the
+			              reset status register
+			    Cell #7 : Flags used to control reset behavior,
+			              availible flags defined in the DT include
+			              file <dt-bindings/reset/ti-syscon.h>
+
+SysCon Reset Consumer Nodes
+===========================
+Each of the reset consumer nodes should have the following properties,
+in addition to their own properties.
+
+Required properties:
+--------------------
+ - resets	: A phandle to the reset controller node and an index number
+		  to a reset specifier as defined above.
+
+Please also refer to Documentation/devicetree/bindings/reset/reset.txt for
+common reset controller usage by consumers.
+
+Example:
+--------
+The following example demonstrates a syscon node, the reset controller node
+using the syscon node, and a consumer (a DSP device) on the TI Keystone 2
+Edison SoC.
+
+/ {
+	soc {
+		psc: power-sleep-controller@02350000 {
+			compatible = "syscon", "simple-mfd";
+			reg = <0x02350000 0x1000>;
+
+			pscrst: psc-reset {
+				compatible = "ti,k2e-pscrst", "ti,syscon-reset";
+				#reset-cells = <1>;
+
+				ti,reset-bits = <
+					0xa3c 8 0xa3c 8 0x83c 8 (ASSERT_SET|DEASSERT_CLEAR|STATUS_SET)   /* 0: pcrst-dsp0 */
+					0xa40 5 0xa44 3 0     0 (ASSERT_SET|DEASSERT_CLEAR|STATUS_NONE)  /* 1: pcrst-example */
+				>;
+			};
+		};
+
+		dsp0: dsp0 {
+			...
+			resets = <&pscrst 0>;
+			...
+		};
+	};
+};

Documentation/devicetree/bindings/serial/cirrus,clps711x-uart.txt

 * Cirrus Logic CLPS711X Universal Asynchronous Receiver/Transmitter (UART)
 
 Required properties:
-- compatible: Should be "cirrus,clps711x-uart".
+- compatible: Should be "cirrus,ep7209-uart".
 - reg: Address and length of the register set for the device.
 - interrupts: Should contain UART TX and RX interrupt.
 - clocks: Should contain UART core clock number.
@@ -20,7 +20,7 @@ Example:
 	};
 
 	uart1: uart@80000480 {
-		compatible = "cirrus,clps711x-uart";
+		compatible = "cirrus,ep7312-uart","cirrus,ep7209-uart";
 		reg = <0x80000480 0x80>;
 		interrupts = <12 13>;
 		clocks = <&clks 11>;

Documentation/devicetree/bindings/soc/qcom/qcom,smp2p.txt

@@ -68,7 +68,7 @@ important.
 	Value type: <u32>
 	Definition: must be 2 - denoting the bit in the entry and IRQ flags
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for outgoing entries
 	Value type: <u32>
 	Definition: must be 1 - denoting the bit in the entry
@@ -92,7 +92,7 @@ wcnss-smp2p {
 	wcnss_smp2p_out: master-kernel {
 		qcom,entry-name = "master-kernel";
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smp2p_in: slave-kernel {

Documentation/devicetree/bindings/soc/qcom/qcom,smsm.txt

@@ -51,7 +51,7 @@ important.
 	Definition: specifies the offset, in words, of the first bit for this
 		    entry
 
-- #qcom,state-cells:
+- #qcom,smem-state-cells:
 	Usage: required for local entry
 	Value type: <u32>
 	Definition: must be 1 - denotes bit number
@@ -91,7 +91,7 @@ smsm {
 	apps_smsm: apps@0 {
 		reg = <0>;
 
-		#qcom,state-cells = <1>;
+		#qcom,smem-state-cells = <1>;
 	};
 
 	wcnss_smsm: wcnss@7 {

Documentation/devicetree/bindings/timer/cirrus,clps711x-timer.txt

 * Cirrus Logic CLPS711X Timer Counter
 
 Required properties:
-- compatible: Shall contain "cirrus,clps711x-timer".
+- compatible: Shall contain "cirrus,ep7209-timer".
 - reg       : Address and length of the register set.
 - interrupts: The interrupt number of the timer.
 - clocks    : phandle of timer reference clock.
@@ -15,14 +15,14 @@ Example:
 	};
 
 	timer1: timer@80000300 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000300 0x4>;
 		interrupts = <8>;
 		clocks = <&clks 5>;
 	};
 
 	timer2: timer@80000340 {
-		compatible = "cirrus,ep7312-timer", "cirrus,clps711x-timer";
+		compatible = "cirrus,ep7312-timer", "cirrus,ep7209-timer";
 		reg = <0x80000340 0x4>;
 		interrupts = <9>;
 		clocks = <&clks 6>;

Documentation/driver-model/devres.txt

@@ -352,6 +352,10 @@ REGULATOR
   devm_regulator_put()
   devm_regulator_register()
 
+RESET
+  devm_reset_control_get()
+  devm_reset_controller_register()
+
 SLAVE DMA ENGINE
   devm_acpi_dma_controller_register()
 

MAINTAINERS

@@ -1536,6 +1536,7 @@ M:	David Brown <david.brown@linaro.org>
 L:	linux-arm-msm@vger.kernel.org
 L:	linux-soc@vger.kernel.org
 S:	Maintained
+F:	Documentation/devicetree/bindings/soc/qcom/
 F:	arch/arm/boot/dts/qcom-*.dts
 F:	arch/arm/boot/dts/qcom-*.dtsi
 F:	arch/arm/mach-qcom/
@@ -1841,7 +1842,6 @@ L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
 T:	git git://git.linaro.org/people/ulfh/clk.git
 S:	Maintained
 F:	drivers/clk/ux500/
-F:	include/linux/platform_data/clk-ux500.h
 
 ARM/VERSATILE EXPRESS PLATFORM
 M:	Liviu Dudau <liviu.dudau@arm.com>

arch/arm/boot/dts/exynos-mfc-reserved-memory.dtsi

+/*
+ * Samsung's Exynos SoC MFC (Video Codec) reserved memory common definition.
+ *
+ * Copyright (c) 2016 Samsung Electronics Co., Ltd
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/ {
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		mfc_left: region@51000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x51000000 0x800000>;
+		};
+
+		mfc_right: region@43000000 {
+			compatible = "shared-dma-pool";
+			no-map;
+			reg = <0x43000000 0x800000>;
+		};
+	};
+};

arch/arm/boot/dts/exynos4210-origen.dts

@@ -18,6 +18,7 @@
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4210";
@@ -288,8 +289,7 @@ buck7_reg: BUCK7 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 

arch/arm/boot/dts/exynos4210-smdkv310.dts

@@ -17,6 +17,7 @@
 /dts-v1/;
 #include "exynos4210.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung smdkv310 evaluation board based on Exynos4210";
@@ -133,8 +134,7 @@ key_e {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 

arch/arm/boot/dts/exynos4412-odroid-common.dtsi

@@ -13,6 +13,7 @@
 #include "exynos4412.dtsi"
 #include "exynos4412-ppmu-common.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	chosen {
@@ -499,6 +500,11 @@ &i2s0 {
 	clock-names = "iis", "i2s_opclk0", "i2s_opclk1";
 };
 
+&mfc {
+	memory-region = <&mfc_left>, <&mfc_right>;
+	status = "okay";
+};
+
 &mixer {
 	status = "okay";
 };

arch/arm/boot/dts/exynos4412-origen.dts

@@ -16,6 +16,7 @@
 #include "exynos4412.dtsi"
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/input/input.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Origen evaluation board based on Exynos4412";
@@ -466,8 +467,7 @@ key_enter {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 

arch/arm/boot/dts/exynos4412-smdk4412.dts

@@ -14,6 +14,7 @@
 
 /dts-v1/;
 #include "exynos4412.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung SMDK evaluation board based on Exynos4412";
@@ -112,8 +113,7 @@ key_E {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 	status = "okay";
 };
 

arch/arm/boot/dts/exynos5250-arndale.dts

@@ -14,6 +14,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Arndale evaluation board based on EXYNOS5250";
@@ -516,8 +517,7 @@ &i2s0 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5250-smdk5250.dts

@@ -13,6 +13,7 @@
 #include <dt-bindings/gpio/gpio.h>
 #include <dt-bindings/interrupt-controller/irq.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "SAMSUNG SMDK5250 board based on EXYNOS5250";
@@ -344,8 +345,7 @@ &i2s0 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5250-spring.dts

@@ -14,6 +14,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include "exynos5250.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Spring";
@@ -425,8 +426,7 @@ &i2s0 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5420-arndale-octa.dts

@@ -16,6 +16,7 @@
 #include <dt-bindings/interrupt-controller/irq.h>
 #include <dt-bindings/input/input.h>
 #include <dt-bindings/clock/samsung,s2mps11.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Insignal Arndale Octa evaluation board based on EXYNOS5420";
@@ -347,8 +348,7 @@ buck10_reg: BUCK10 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5420-peach-pit.dts

@@ -16,6 +16,7 @@
 #include <dt-bindings/regulator/maxim,max77802.h>
 #include "exynos5420.dtsi"
 #include "exynos5420-cpus.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Peach Pit Rev 6+";
@@ -702,8 +703,7 @@ &i2s0 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5420-smdk5420.dts

@@ -13,6 +13,7 @@
 #include "exynos5420.dtsi"
 #include "exynos5420-cpus.dtsi"
 #include <dt-bindings/gpio/gpio.h>
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Samsung SMDK5420 board based on EXYNOS5420";
@@ -355,8 +356,7 @@ hdmiddc@50 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5422-odroidxu3-common.dtsi

@@ -17,6 +17,7 @@
 #include "exynos5800.dtsi"
 #include "exynos5422-cpus.dtsi"
 #include "exynos5422-cpu-thermal.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	memory {
@@ -406,8 +407,7 @@ hdmiddc@50 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/boot/dts/exynos5800-peach-pi.dts

@@ -16,6 +16,7 @@
 #include <dt-bindings/regulator/maxim,max77802.h>
 #include "exynos5800.dtsi"
 #include "exynos5420-cpus.dtsi"
+#include "exynos-mfc-reserved-memory.dtsi"
 
 / {
 	model = "Google Peach Pi Rev 10+";
@@ -670,8 +671,7 @@ &i2s0 {
 };
 
 &mfc {
-	samsung,mfc-r = <0x43000000 0x800000>;
-	samsung,mfc-l = <0x51000000 0x800000>;
+	memory-region = <&mfc_left>, <&mfc_right>;
 };
 
 &mmc_0 {

arch/arm/mach-exynos/Kconfig

@@ -18,6 +18,7 @@ menuconfig ARCH_EXYNOS
 	select EXYNOS_THERMAL
 	select EXYNOS_PMU
 	select EXYNOS_SROM
+	select EXYNOS_PM_DOMAINS if PM_GENERIC_DOMAINS
 	select GPIOLIB
 	select HAVE_ARM_SCU if SMP
 	select HAVE_S3C2410_I2C if I2C

arch/arm/mach-exynos/Makefile

@@ -13,7 +13,6 @@ obj-$(CONFIG_ARCH_EXYNOS)	+= exynos.o exynos-smc.o firmware.o
 
 obj-$(CONFIG_EXYNOS_CPU_SUSPEND) += pm.o sleep.o
 obj-$(CONFIG_PM_SLEEP)		+= suspend.o
-obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o
 
 obj-$(CONFIG_SMP)		+= platsmp.o headsmp.o
 
@@ -23,5 +22,3 @@ AFLAGS_sleep.o			:=-Wa,-march=armv7-a$(plus_sec)
 
 obj-$(CONFIG_EXYNOS5420_MCPM)	+= mcpm-exynos.o
 CFLAGS_mcpm-exynos.o		+= -march=armv7-a
-
-obj-$(CONFIG_S5P_DEV_MFC)	+= s5p-dev-mfc.o

arch/arm/mach-exynos/exynos.c

@@ -27,7 +27,6 @@
 #include <plat/cpu.h>
 
 #include "common.h"
-#include "mfc.h"
 
 static struct map_desc exynos4_iodesc[] __initdata = {
 	{
@@ -235,23 +234,6 @@ static char const *const exynos_dt_compat[] __initconst = {
 	NULL
 };
 
-static void __init exynos_reserve(void)
-{
-#ifdef CONFIG_S5P_DEV_MFC
-	int i;
-	char *mfc_mem[] = {
-		"samsung,mfc-v5",
-		"samsung,mfc-v6",
-		"samsung,mfc-v7",
-		"samsung,mfc-v8",
-	};
-
-	for (i = 0; i < ARRAY_SIZE(mfc_mem); i++)
-		if (of_scan_flat_dt(s5p_fdt_alloc_mfc_mem, mfc_mem[i]))
-			break;
-#endif
-}
-
 static void __init exynos_dt_fixup(void)
 {
 	/*
@@ -273,6 +255,5 @@ DT_MACHINE_START(EXYNOS_DT, "SAMSUNG EXYNOS (Flattened Device Tree)")
 	.init_machine	= exynos_dt_machine_init,
 	.init_late	= exynos_init_late,
 	.dt_compat	= exynos_dt_compat,
-	.reserve	= exynos_reserve,
 	.dt_fixup	= exynos_dt_fixup,
 MACHINE_END

arch/arm/mach-exynos/mfc.h

-/*
- * Copyright (C) 2013 Samsung Electronics Co.Ltd
- *
- * This program is free software; you can redistribute  it and/or modify it
- * under  the terms of  the GNU General  Public License as published by the
- * Free Software Foundation;  either version 2 of the  License, or (at your
- * option) any later version.
- */
-
-#ifndef __MACH_EXYNOS_MFC_H
-#define __MACH_EXYNOS_MFC_H __FILE__
-
-int __init s5p_fdt_alloc_mfc_mem(unsigned long node, const char *uname,
-				int depth, void *data);
-
-#endif /* __MACH_EXYNOS_MFC_H */

arch/arm/mach-exynos/s5p-dev-mfc.c

-/*
- * Copyright (C) 2010-2011 Samsung Electronics Co.Ltd
- *
- * Base S5P MFC resource and device definitions
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
- */
-
-#include <linux/kernel.h>
-#include <linux/platform_device.h>
-#include <linux/dma-mapping.h>
-#include <linux/memblock.h>
-#include <linux/ioport.h>
-#include <linux/of_fdt.h>
-#include <linux/of.h>
-
-static struct platform_device s5p_device_mfc_l;
-static struct platform_device s5p_device_mfc_r;
-
-struct s5p_mfc_dt_meminfo {
-	unsigned long	loff;
-	unsigned long	lsize;
-	unsigned long	roff;
-	unsigned long	rsize;
-	char		*compatible;
-};
-
-struct s5p_mfc_reserved_mem {
-	phys_addr_t	base;
-	unsigned long	size;
-	struct device	*dev;
-};
-
-static struct s5p_mfc_reserved_mem s5p_mfc_mem[2] __initdata;
-
-
-static void __init s5p_mfc_reserve_mem(phys_addr_t rbase, unsigned int rsize,
-				phys_addr_t lbase, unsigned int lsize)
-{
-	int i;
-
-	s5p_mfc_mem[0].dev = &s5p_device_mfc_r.dev;
-	s5p_mfc_mem[0].base = rbase;
-	s5p_mfc_mem[0].size = rsize;
-
-	s5p_mfc_mem[1].dev = &s5p_device_mfc_l.dev;
-	s5p_mfc_mem[1].base = lbase;
-	s5p_mfc_mem[1].size = lsize;
-
-	for (i = 0; i < ARRAY_SIZE(s5p_mfc_mem); i++) {
-		struct s5p_mfc_reserved_mem *area = &s5p_mfc_mem[i];
-		if (memblock_remove(area->base, area->size)) {
-			printk(KERN_ERR "Failed to reserve memory for MFC device (%ld bytes at 0x%08lx)\n",
-			       area->size, (unsigned long) area->base);
-			area->base = 0;
-		}
-	}
-}
-
-int __init s5p_fdt_alloc_mfc_mem(unsigned long node, const char *uname,
-				int depth, void *data)
-{
-	const __be32 *prop;
-	int len;
-	struct s5p_mfc_dt_meminfo mfc_mem;
-
-	if (!data)
-		return 0;
-
-	if (!of_flat_dt_is_compatible(node, data))
-		return 0;
-
-	prop = of_get_flat_dt_prop(node, "samsung,mfc-l", &len);
-	if (!prop || (len != 2 * sizeof(unsigned long)))
-		return 0;
-
-	mfc_mem.loff = be32_to_cpu(prop[0]);
-	mfc_mem.lsize = be32_to_cpu(prop[1]);
-
-	prop = of_get_flat_dt_prop(node, "samsung,mfc-r", &len);
-	if (!prop || (len != 2 * sizeof(unsigned long)))
-		return 0;
-
-	mfc_mem.roff = be32_to_cpu(prop[0]);
-	mfc_mem.rsize = be32_to_cpu(prop[1]);
-
-	s5p_mfc_reserve_mem(mfc_mem.roff, mfc_mem.rsize,
-			mfc_mem.loff, mfc_mem.lsize);
-
-	return 1;
-}

arch/arm/mach-omap2/board-rx51-peripherals.c

@@ -1242,11 +1242,6 @@ static struct pwm_omap_dmtimer_pdata __maybe_unused pwm_dmtimer_pdata = {
 #if defined(CONFIG_IR_RX51) || defined(CONFIG_IR_RX51_MODULE)
 static struct lirc_rx51_platform_data rx51_lirc_data = {
 	.set_max_mpu_wakeup_lat = omap_pm_set_max_mpu_wakeup_lat,
-	.pwm_timer = 9, /* Use GPT 9 for CIR */
-#if IS_ENABLED(CONFIG_OMAP_DM_TIMER)
-	.dmtimer = &pwm_dmtimer_pdata,
-#endif
-
 };
 
 static struct platform_device rx51_lirc_device = {

arch/arm/mach-omap2/pdata-quirks.c

@@ -274,8 +274,6 @@ static struct platform_device omap3_rom_rng_device = {
 	},
 };
 
-static struct platform_device rx51_lirc_device;
-
 static void __init nokia_n900_legacy_init(void)
 {
 	hsmmc2_internal_input_clk();
@@ -294,10 +292,7 @@ static void __init nokia_n900_legacy_init(void)
 
 		pr_info("RX-51: Registering OMAP3 HWRNG device\n");
 		platform_device_register(&omap3_rom_rng_device);
-
 	}
-
-	platform_device_register(&rx51_lirc_device);
 }
 
 static void __init omap3_tao3530_legacy_init(void)
@@ -492,10 +487,6 @@ static struct pwm_omap_dmtimer_pdata pwm_dmtimer_pdata = {
 
 static struct lirc_rx51_platform_data __maybe_unused rx51_lirc_data = {
 	.set_max_mpu_wakeup_lat = omap_pm_set_max_mpu_wakeup_lat,
-	.pwm_timer = 9, /* Use GPT 9 for CIR */
-#if IS_ENABLED(CONFIG_OMAP_DM_TIMER)
-	.dmtimer = &pwm_dmtimer_pdata,
-#endif
 };
 
 static struct platform_device __maybe_unused rx51_lirc_device = {
@@ -543,6 +534,7 @@ static struct of_dev_auxdata omap_auxdata_lookup[] __initdata = {
 		       &omap3_iommu_pdata),
 	OF_DEV_AUXDATA("ti,omap3-hsmmc", 0x4809c000, "4809c000.mmc", &mmc_pdata[0]),
 	OF_DEV_AUXDATA("ti,omap3-hsmmc", 0x480b4000, "480b4000.mmc", &mmc_pdata[1]),
+	OF_DEV_AUXDATA("nokia,n900-ir", 0, "n900-ir", &rx51_lirc_data),
 	/* Only on am3517 */
 	OF_DEV_AUXDATA("ti,davinci_mdio", 0x5c030000, "davinci_mdio.0", NULL),
 	OF_DEV_AUXDATA("ti,am3517-emac", 0x5c000000, "davinci_emac.0",

arch/arm/mach-ux500/Makefile

@@ -2,11 +2,9 @@
 # Makefile for the linux kernel, U8500 machine.
 #
 
-obj-y				:= cpu.o id.o pm.o
-obj-$(CONFIG_CACHE_L2X0)	+= cache-l2x0.o
+obj-y				:= pm.o
 obj-$(CONFIG_UX500_SOC_DB8500)	+= cpu-db8500.o
-obj-$(CONFIG_MACH_MOP500)	+= board-mop500-regulators.o \
-				board-mop500-audio.o
+obj-$(CONFIG_MACH_MOP500)	+= board-mop500-audio.o
 obj-$(CONFIG_SMP)		+= platsmp.o
 obj-$(CONFIG_HOTPLUG_CPU)	+= hotplug.o
 obj-$(CONFIG_PM_GENERIC_DOMAINS) += pm_domains.o

arch/arm/mach-ux500/board-mop500-regulators.h

-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * License Terms: GNU General Public License v2
- *
- * Author: Bengt Jonsson <bengt.g.jonsson@stericsson.com> for ST-Ericsson
- *
- * MOP500 board specific initialization for regulators
- */
-
-#ifndef __BOARD_MOP500_REGULATORS_H
-#define __BOARD_MOP500_REGULATORS_H
-
-#include <linux/regulator/machine.h>
-#include <linux/regulator/ab8500.h>
-
-extern struct ab8500_regulator_platform_data ab8500_regulator_plat_data;
-extern struct ab8500_regulator_platform_data ab8505_regulator_plat_data;
-extern struct regulator_init_data tps61052_regulator;
-extern struct regulator_init_data gpio_en_3v3_regulator;
-
-void mop500_regulator_init(void);
-
-#endif

arch/arm/mach-ux500/cache-l2x0.c

-/*
- * Copyright (C) ST-Ericsson SA 2011
- *
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/io.h>
-#include <linux/of.h>
-#include <linux/of_address.h>
-
-#include <asm/outercache.h>
-#include <asm/hardware/cache-l2x0.h>
-
-#include "db8500-regs.h"
-#include "id.h"
-
-static int __init ux500_l2x0_unlock(void)
-{
-	int i;
-	struct device_node *np;
-	void __iomem *l2x0_base;
-
-	np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
-	l2x0_base = of_iomap(np, 0);
-	of_node_put(np);
-	if (!l2x0_base)
-		return -ENODEV;
-
-	/*
-	 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
-	 * apparently locks both caches before jumping to the kernel. The
-	 * l2x0 core will not touch the unlock registers if the l2x0 is
-	 * already enabled, so we do it right here instead. The PL310 has
-	 * 8 sets of registers, one per possible CPU.
-	 */
-	for (i = 0; i < 8; i++) {
-		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
-			       i * L2X0_LOCKDOWN_STRIDE);
-		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
-			       i * L2X0_LOCKDOWN_STRIDE);
-	}
-	iounmap(l2x0_base);
-	return 0;
-}
-
-static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
-{
-	/*
-	 * We can't write to secure registers as we are in non-secure
-	 * mode, until we have some SMI service available.
-	 */
-}
-
-static int __init ux500_l2x0_init(void)
-{
-	/* Multiplatform guard */
-	if (!((cpu_is_u8500_family() || cpu_is_ux540_family())))
-		return -ENODEV;
-
-	/* Unlock before init */
-	ux500_l2x0_unlock();
-	outer_cache.write_sec = ux500_l2c310_write_sec;
-	l2x0_of_init(0, ~0);
-
-	return 0;
-}
-early_initcall(ux500_l2x0_init);

arch/arm/mach-ux500/cpu-db8500.c

@@ -12,41 +12,107 @@
 #include <linux/init.h>
 #include <linux/device.h>
 #include <linux/amba/bus.h>
+#include <linux/init.h>
 #include <linux/interrupt.h>
 #include <linux/irq.h>
+#include <linux/irqchip.h>
+#include <linux/irqchip/arm-gic.h>
+#include <linux/mfd/dbx500-prcmu.h>
+#include <linux/platform_data/arm-ux500-pm.h>
 #include <linux/platform_device.h>
 #include <linux/io.h>
-#include <linux/mfd/abx500/ab8500.h>
-#include <linux/mfd/dbx500-prcmu.h>
 #include <linux/of.h>
+#include <linux/of_address.h>
 #include <linux/of_platform.h>
 #include <linux/perf/arm_pmu.h>
 #include <linux/regulator/machine.h>
-#include <linux/random.h>
 
+#include <asm/outercache.h>
+#include <asm/hardware/cache-l2x0.h>
 #include <asm/mach/map.h>
+#include <asm/mach/arch.h>
 
 #include "setup.h"
 
-#include "board-mop500-regulators.h"
 #include "board-mop500.h"
 #include "db8500-regs.h"
-#include "id.h"
 
-static struct ab8500_platform_data ab8500_platdata = {
-	.regulator	= &ab8500_regulator_plat_data,
-};
+static int __init ux500_l2x0_unlock(void)
+{
+	int i;
+	struct device_node *np;
+	void __iomem *l2x0_base;
 
-static struct prcmu_pdata db8500_prcmu_pdata = {
-	.ab_platdata	= &ab8500_platdata,
-	.version_offset	= DB8500_PRCMU_FW_VERSION_OFFSET,
-	.legacy_offset	= DB8500_PRCMU_LEGACY_OFFSET,
-};
+	np = of_find_compatible_node(NULL, NULL, "arm,pl310-cache");
+	l2x0_base = of_iomap(np, 0);
+	of_node_put(np);
+	if (!l2x0_base)
+		return -ENODEV;
+
+	/*
+	 * Unlock Data and Instruction Lock if locked. Ux500 U-Boot versions
+	 * apparently locks both caches before jumping to the kernel. The
+	 * l2x0 core will not touch the unlock registers if the l2x0 is
+	 * already enabled, so we do it right here instead. The PL310 has
+	 * 8 sets of registers, one per possible CPU.
+	 */
+	for (i = 0; i < 8; i++) {
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_D_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+		writel_relaxed(0x0, l2x0_base + L2X0_LOCKDOWN_WAY_I_BASE +
+			       i * L2X0_LOCKDOWN_STRIDE);
+	}
+	iounmap(l2x0_base);
+	return 0;
+}
+
+static void ux500_l2c310_write_sec(unsigned long val, unsigned reg)
+{
+	/*
+	 * We can't write to secure registers as we are in non-secure
+	 * mode, until we have some SMI service available.
+	 */
+}
 
-static void __init u8500_map_io(void)
+/*
+ * FIXME: Should we set up the GPIO domain here?
+ *
+ * The problem is that we cannot put the interrupt resources into the platform
+ * device until the irqdomain has been added. Right now, we set the GIC interrupt
+ * domain from init_irq(), then load the gpio driver from
+ * core_initcall(nmk_gpio_init) and add the platform devices from
+ * arch_initcall(customize_machine).
+ *
+ * This feels fragile because it depends on the gpio device getting probed
+ * _before_ any device uses the gpio interrupts.
+*/
+static void __init ux500_init_irq(void)
+{
+	struct device_node *np;
+	struct resource r;
+
+	irqchip_init();
+	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
+	of_address_to_resource(np, 0, &r);
+	of_node_put(np);
+	if (!r.start) {
+		pr_err("could not find PRCMU base resource\n");
+		return;
+	}
+	prcmu_early_init(r.start, r.end-r.start);
+	ux500_pm_init(r.start, r.end-r.start);
+
+	/* Unlock before init */
+	ux500_l2x0_unlock();
+	outer_cache.write_sec = ux500_l2c310_write_sec;
+}
+
+static void ux500_restart(enum reboot_mode mode, const char *cmd)
 {
-	debug_ll_io_init();
-	ux500_setup_id();
+	local_irq_disable();
+	local_fiq_disable();
+
+	prcmu_system_reset(0);
 }
 
 /*
@@ -73,31 +139,6 @@ static struct arm_pmu_platdata db8500_pmu_platdata = {
 	.handle_irq		= db8500_pmu_handler,
 };
 
-static const char *db8500_read_soc_id(void)
-{
-	void __iomem *uid;
-	const char *retstr;
-
-	uid = ioremap(U8500_BB_UID_BASE, 0x20);
-	if (!uid)
-		return NULL;
-	/* Throw these device-specific numbers into the entropy pool */
-	add_device_randomness(uid, 0x14);
-	retstr = kasprintf(GFP_KERNEL, "%08x%08x%08x%08x%08x",
-			 readl((u32 *)uid+0),
-			 readl((u32 *)uid+1), readl((u32 *)uid+2),
-			 readl((u32 *)uid+3), readl((u32 *)uid+4));
-	iounmap(uid);
-	return retstr;
-}
-
-static struct device * __init db8500_soc_device_init(void)
-{
-	const char *soc_id = db8500_read_soc_id();
-
-	return ux500_soc_device_init(soc_id);
-}
-
 static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	/* Requires call-back bindings. */
 	OF_DEV_AUXDATA("arm,cortex-a9-pmu", 0, "arm-pmu", &db8500_pmu_platdata),
@@ -111,8 +152,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 	OF_DEV_AUXDATA("stericsson,ux500-msp-i2s", 0x80125000,
 		       "ux500-msp-i2s.3", &msp3_platform_data),
 	/* Requires non-DT:able platform data. */
-	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
-			&db8500_prcmu_pdata),
+	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", NULL),
 	OF_DEV_AUXDATA("stericsson,ux500-cryp", 0xa03cb000, "cryp1", NULL),
 	OF_DEV_AUXDATA("stericsson,ux500-hash", 0xa03c2000, "hash1", NULL),
 	OF_DEV_AUXDATA("stericsson,snd-soc-mop500", 0, "snd-soc-mop500.0",
@@ -121,8 +161,7 @@ static struct of_dev_auxdata u8500_auxdata_lookup[] __initdata = {
 };
 
 static struct of_dev_auxdata u8540_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu",
-			&db8500_prcmu_pdata),
+	OF_DEV_AUXDATA("stericsson,db8500-prcmu", 0x80157000, "db8500-prcmu", NULL),
 	{},
 };
 
@@ -136,15 +175,13 @@ static const struct of_device_id u8500_local_bus_nodes[] = {
 
 static void __init u8500_init_machine(void)
 {
-	struct device *parent = db8500_soc_device_init();
-
 	/* automatically probe child nodes of dbx5x0 devices */
 	if (of_machine_is_compatible("st-ericsson,u8540"))
 		of_platform_populate(NULL, u8500_local_bus_nodes,
-				     u8540_auxdata_lookup, parent);
+				     u8540_auxdata_lookup, NULL);
 	else
 		of_platform_populate(NULL, u8500_local_bus_nodes,
-				     u8500_auxdata_lookup, parent);
+				     u8500_auxdata_lookup, NULL);
 }
 
 static const char * stericsson_dt_platform_compat[] = {
@@ -156,10 +193,10 @@ static const char * stericsson_dt_platform_compat[] = {
 };
 
 DT_MACHINE_START(U8500_DT, "ST-Ericsson Ux5x0 platform (Device Tree Support)")
-	.map_io		= u8500_map_io,
+	.l2c_aux_val    = 0,
+	.l2c_aux_mask	= ~0,
 	.init_irq	= ux500_init_irq,
 	.init_machine	= u8500_init_machine,
-	.init_late	= NULL,
 	.dt_compat      = stericsson_dt_platform_compat,
 	.restart        = ux500_restart,
 MACHINE_END

arch/arm/mach-ux500/cpu.c

-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * Author: Lee Jones <lee.jones@linaro.org> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#include <linux/platform_device.h>
-#include <linux/io.h>
-#include <linux/mfd/dbx500-prcmu.h>
-#include <linux/sys_soc.h>
-#include <linux/err.h>
-#include <linux/slab.h>
-#include <linux/stat.h>
-#include <linux/of.h>
-#include <linux/of_irq.h>
-#include <linux/of_address.h>
-#include <linux/irq.h>
-#include <linux/irqchip.h>
-#include <linux/irqchip/arm-gic.h>
-#include <linux/platform_data/clk-ux500.h>
-#include <linux/platform_data/arm-ux500-pm.h>
-
-#include <asm/mach/map.h>
-
-#include "setup.h"
-
-#include "board-mop500.h"
-#include "db8500-regs.h"
-#include "id.h"
-
-void ux500_restart(enum reboot_mode mode, const char *cmd)
-{
-	local_irq_disable();
-	local_fiq_disable();
-
-	prcmu_system_reset(0);
-}
-
-/*
- * FIXME: Should we set up the GPIO domain here?
- *
- * The problem is that we cannot put the interrupt resources into the platform
- * device until the irqdomain has been added. Right now, we set the GIC interrupt
- * domain from init_irq(), then load the gpio driver from
- * core_initcall(nmk_gpio_init) and add the platform devices from
- * arch_initcall(customize_machine).
- *
- * This feels fragile because it depends on the gpio device getting probed
- * _before_ any device uses the gpio interrupts.
-*/
-void __init ux500_init_irq(void)
-{
-	struct device_node *np;
-	struct resource r;
-
-	irqchip_init();
-	np = of_find_compatible_node(NULL, NULL, "stericsson,db8500-prcmu");
-	of_address_to_resource(np, 0, &r);
-	of_node_put(np);
-	if (!r.start) {
-		pr_err("could not find PRCMU base resource\n");
-		return;
-	}
-	prcmu_early_init(r.start, r.end-r.start);
-	ux500_pm_init(r.start, r.end-r.start);
-
-	/*
-	 * Init clocks here so that they are available for system timer
-	 * initialization.
-	 */
-	if (cpu_is_u8500_family())
-		u8500_clk_init();
-	else if (cpu_is_u9540())
-		u9540_clk_init();
-	else if (cpu_is_u8540())
-		u8540_clk_init();
-}
-
-static const char * __init ux500_get_machine(void)
-{
-	return kasprintf(GFP_KERNEL, "DB%4x", dbx500_partnumber());
-}
-
-static const char * __init ux500_get_family(void)
-{
-	return kasprintf(GFP_KERNEL, "ux500");
-}
-
-static const char * __init ux500_get_revision(void)
-{
-	unsigned int rev = dbx500_revision();
-
-	if (rev == 0x01)
-		return kasprintf(GFP_KERNEL, "%s", "ED");
-	else if (rev >= 0xA0)
-		return kasprintf(GFP_KERNEL, "%d.%d",
-				 (rev >> 4) - 0xA + 1, rev & 0xf);
-
-	return kasprintf(GFP_KERNEL, "%s", "Unknown");
-}
-
-static ssize_t ux500_get_process(struct device *dev,
-					struct device_attribute *attr,
-					char *buf)
-{
-	if (dbx500_id.process == 0x00)
-		return sprintf(buf, "Standard\n");
-
-	return sprintf(buf, "%02xnm\n", dbx500_id.process);
-}
-
-static void __init soc_info_populate(struct soc_device_attribute *soc_dev_attr,
-				     const char *soc_id)
-{
-	soc_dev_attr->soc_id   = soc_id;
-	soc_dev_attr->machine  = ux500_get_machine();
-	soc_dev_attr->family   = ux500_get_family();
-	soc_dev_attr->revision = ux500_get_revision();
-}
-
-static const struct device_attribute ux500_soc_attr =
-	__ATTR(process,  S_IRUGO, ux500_get_process,  NULL);
-
-struct device * __init ux500_soc_device_init(const char *soc_id)
-{
-	struct device *parent;
-	struct soc_device *soc_dev;
-	struct soc_device_attribute *soc_dev_attr;
-
-	soc_dev_attr = kzalloc(sizeof(*soc_dev_attr), GFP_KERNEL);
-	if (!soc_dev_attr)
-		return ERR_PTR(-ENOMEM);
-
-	soc_info_populate(soc_dev_attr, soc_id);
-
-	soc_dev = soc_device_register(soc_dev_attr);
-	if (IS_ERR(soc_dev)) {
-	        kfree(soc_dev_attr);
-		return NULL;
-	}
-
-	parent = soc_device_to_device(soc_dev);
-	device_create_file(parent, &ux500_soc_attr);
-
-	return parent;
-}

arch/arm/mach-ux500/id.h

-/*
- * Copyright (C) ST-Ericsson SA 2010
- *
- * Author: Rabin Vincent <rabin.vincent@stericsson.com> for ST-Ericsson
- * License terms: GNU General Public License (GPL) version 2
- */
-
-#ifndef __MACH_UX500_ID
-#define __MACH_UX500_ID
-
-/**
- * struct dbx500_asic_id - fields of the ASIC ID
- * @process: the manufacturing process, 0x40 is 40 nm 0x00 is "standard"
- * @partnumber: hithereto 0x8500 for DB8500
- * @revision: version code in the series
- */
-struct dbx500_asic_id {
-	u16	partnumber;
-	u8	revision;
-	u8	process;
-};
-
-extern struct dbx500_asic_id dbx500_id;
-
-static inline unsigned int __attribute_const__ dbx500_partnumber(void)
-{
-	return dbx500_id.partnumber;
-}
-
-static inline unsigned int __attribute_const__ dbx500_revision(void)
-{
-	return dbx500_id.revision;
-}
-
-/*
- * SOCs
- */
-
-static inline bool __attribute_const__ cpu_is_u8500(void)
-{
-	return dbx500_partnumber() == 0x8500;
-}
-
-static inline bool __attribute_const__ cpu_is_u8520(void)
-{
-	return dbx500_partnumber() == 0x8520;
-}
-
-static inline bool cpu_is_u8500_family(void)
-{
-	return cpu_is_u8500() || cpu_is_u8520();
-}
-
-static inline bool __attribute_const__ cpu_is_u9540(void)
-{
-	return dbx500_partnumber() == 0x9540;
-}
-
-static inline bool __attribute_const__ cpu_is_u8540(void)
-{
-	return dbx500_partnumber() == 0x8540;
-}
-
-static inline bool __attribute_const__ cpu_is_u8580(void)
-{
-	return dbx500_partnumber() == 0x8580;
-}
-
-static inline bool cpu_is_ux540_family(void)
-{
-	return cpu_is_u9540() || cpu_is_u8540() || cpu_is_u8580();
-}
-
-/*
- * 8500 revisions
- */
-
-static inline bool __attribute_const__ cpu_is_u8500ed(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0x00;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v1(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() & 0xf0) == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v10(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v11(void)
-{
-	return cpu_is_u8500() && dbx500_revision() == 0xA1;
-}
-
-static inline bool __attribute_const__ cpu_is_u8500v2(void)
-{
-	return cpu_is_u8500() && ((dbx500_revision() & 0xf0) == 0xB0);
-}
-
-static inline bool cpu_is_u8500v20(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB0);
-}
-
-static inline bool cpu_is_u8500v21(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB1);
-}
-
-static inline bool cpu_is_u8500v22(void)
-{
-	return cpu_is_u8500() && (dbx500_revision() == 0xB2);
-}
-
-static inline bool cpu_is_u8500v20_or_later(void)
-{
-	return (cpu_is_u8500() && !cpu_is_u8500v10() && !cpu_is_u8500v11());
-}
-
-/*
- * 8540 revisions
- */
-
-static inline bool __attribute_const__ cpu_is_u8540v10(void)
-{
-	return cpu_is_u8540() && dbx500_revision() == 0xA0;
-}
-
-static inline bool __attribute_const__ cpu_is_u8580v10(void)
-{
-	return cpu_is_u8580() && dbx500_revision() == 0xA0;
-}
-
-static inline bool ux500_is_svp(void)
-{
-	return false;
-}
-
-#define ux500_unknown_soc()	BUG()
-
-#endif

arch/arm/mach-ux500/platsmp.c

@@ -26,7 +26,6 @@
 #include "setup.h"
 
 #include "db8500-regs.h"
-#include "id.h"
 
 /* Magic triggers in backup RAM */
 #define UX500_CPU1_JUMPADDR_OFFSET 0x1FF4

arch/arm/mach-ux500/setup.h

@@ -11,18 +11,6 @@
 #ifndef __ASM_ARCH_SETUP_H
 #define __ASM_ARCH_SETUP_H
 
-#include <asm/mach/arch.h>
-#include <linux/init.h>
-#include <linux/mfd/abx500/ab8500.h>
-
-void ux500_restart(enum reboot_mode mode, const char *cmd);
-
-void __init ux500_setup_id(void);
-
-extern void __init ux500_init_irq(void);
-
-extern struct device *ux500_soc_device_init(const char *soc_id);
-
 extern void ux500_cpu_die(unsigned int cpu);
 
 #endif /*  __ASM_ARCH_SETUP_H */

arch/arm64/boot/dts/hisilicon/hi6220.dtsi

@@ -5,6 +5,7 @@
  */
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/hisi,hi6220-resets.h>
 #include <dt-bindings/clock/hi6220-clock.h>
 #include <dt-bindings/pinctrl/hisi.h>
 #include <dt-bindings/thermal/thermal.h>
@@ -252,6 +253,7 @@ media_ctrl: media_ctrl@f4410000 {
 			compatible = "hisilicon,hi6220-mediactrl", "syscon";
 			reg = <0x0 0xf4410000 0x0 0x1000>;
 			#clock-cells = <1>;
+			#reset-cells = <1>;
 		};
 
 		pm_ctrl: pm_ctrl@f7032000 {

drivers/bus/Kconfig

@@ -132,6 +132,19 @@ config SUNXI_RSB
 	  with various RSB based devices, such as AXP223, AXP8XX PMICs,
 	  and AC100/AC200 ICs.
 
+# TODO: This uses pm_clk_*() symbols that aren't exported in v4.7 and hence
+# the driver will fail to build as a module. However there are patches to
+# address that queued for v4.8, so this can be turned into a tristate symbol
+# after v4.8-rc1.
+config TEGRA_ACONNECT
+	bool "Tegra ACONNECT Bus Driver"
+	depends on ARCH_TEGRA_210_SOC
+	depends on OF && PM
+	select PM_CLK
+	help
+	  Driver for the Tegra ACONNECT bus which is used to interface with
+	  the devices inside the Audio Processing Engine (APE) for Tegra210.
+
 config UNIPHIER_SYSTEM_BUS
 	tristate "UniPhier System Bus driver"
 	depends on ARCH_UNIPHIER && OF

drivers/bus/Makefile

@@ -17,5 +17,6 @@ obj-$(CONFIG_OMAP_INTERCONNECT)	+= omap_l3_smx.o omap_l3_noc.o
 obj-$(CONFIG_OMAP_OCP2SCP)	+= omap-ocp2scp.o
 obj-$(CONFIG_SUNXI_RSB)		+= sunxi-rsb.o
 obj-$(CONFIG_SIMPLE_PM_BUS)	+= simple-pm-bus.o
+obj-$(CONFIG_TEGRA_ACONNECT)	+= tegra-aconnect.o
 obj-$(CONFIG_UNIPHIER_SYSTEM_BUS)	+= uniphier-system-bus.o
 obj-$(CONFIG_VEXPRESS_CONFIG)	+= vexpress-config.o

drivers/bus/tegra-aconnect.c

+/*
+ * Tegra ACONNECT Bus Driver
+ *
+ * Copyright (C) 2016, NVIDIA CORPORATION.  All rights reserved.
+ *
+ * This file is subject to the terms and conditions of the GNU General Public
+ * License.  See the file "COPYING" in the main directory of this archive
+ * for more details.
+ */
+
+#include <linux/clk.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/platform_device.h>
+#include <linux/pm_clock.h>
+#include <linux/pm_runtime.h>
+
+static int tegra_aconnect_add_clock(struct device *dev, char *name)
+{
+	struct clk *clk;
+	int ret;
+
+	clk = clk_get(dev, name);
+	if (IS_ERR(clk)) {
+		dev_err(dev, "%s clock not found\n", name);
+		return PTR_ERR(clk);
+	}
+
+	ret = pm_clk_add_clk(dev, clk);
+	if (ret)
+		clk_put(clk);
+
+	return ret;
+}
+
+static int tegra_aconnect_probe(struct platform_device *pdev)
+{
+	int ret;
+
+	if (!pdev->dev.of_node)
+		return -EINVAL;
+
+	ret = pm_clk_create(&pdev->dev);
+	if (ret)
+		return ret;
+
+	ret = tegra_aconnect_add_clock(&pdev->dev, "ape");
+	if (ret)
+		goto clk_destroy;
+
+	ret = tegra_aconnect_add_clock(&pdev->dev, "apb2ape");
+	if (ret)
+		goto clk_destroy;
+
+	pm_runtime_enable(&pdev->dev);
+
+	of_platform_populate(pdev->dev.of_node, NULL, NULL, &pdev->dev);
+
+	dev_info(&pdev->dev, "Tegra ACONNECT bus registered\n");
+
+	return 0;
+
+clk_destroy:
+	pm_clk_destroy(&pdev->dev);
+
+	return ret;
+}
+
+static int tegra_aconnect_remove(struct platform_device *pdev)
+{
+	pm_runtime_disable(&pdev->dev);
+
+	pm_clk_destroy(&pdev->dev);
+
+	return 0;
+}
+
+static int tegra_aconnect_runtime_resume(struct device *dev)
+{
+	return pm_clk_resume(dev);
+}
+
+static int tegra_aconnect_runtime_suspend(struct device *dev)
+{
+	return pm_clk_suspend(dev);
+}
+
+static const struct dev_pm_ops tegra_aconnect_pm_ops = {
+	SET_RUNTIME_PM_OPS(tegra_aconnect_runtime_suspend,
+			   tegra_aconnect_runtime_resume, NULL)
+};
+
+static const struct of_device_id tegra_aconnect_of_match[] = {
+	{ .compatible = "nvidia,tegra210-aconnect", },
+	{ }
+};
+MODULE_DEVICE_TABLE(of, tegra_aconnect_of_match);
+
+static struct platform_driver tegra_aconnect_driver = {
+	.probe = tegra_aconnect_probe,
+	.remove = tegra_aconnect_remove,
+	.driver = {
+		.name = "tegra-aconnect",
+		.of_match_table = tegra_aconnect_of_match,
+		.pm = &tegra_aconnect_pm_ops,
+	},
+};
+module_platform_driver(tegra_aconnect_driver);
+
+MODULE_DESCRIPTION("NVIDIA Tegra ACONNECT Bus Driver");
+MODULE_AUTHOR("Jon Hunter <jonathanh@nvidia.com>");
+MODULE_LICENSE("GPL v2");

drivers/clk/clk-clps711x.c

@@ -184,5 +184,5 @@ static void __init clps711x_clk_init_dt(struct device_node *np)
 	of_clk_add_provider(np, of_clk_src_onecell_get,
 			    &clps711x_clk->clk_data);
 }
-CLK_OF_DECLARE(clps711x, "cirrus,clps711x-clk", clps711x_clk_init_dt);
+CLK_OF_DECLARE(clps711x, "cirrus,ep7209-clk", clps711x_clk_init_dt);
 #endif

drivers/clk/ux500/u8500_of_clk.c

@@ -11,7 +11,6 @@
 #include <linux/of_address.h>
 #include <linux/clk-provider.h>
 #include <linux/mfd/dbx500-prcmu.h>
-#include <linux/platform_data/clk-ux500.h>
 #include "clk.h"
 
 #define PRCC_NUM_PERIPH_CLUSTERS 6
@@ -48,11 +47,6 @@ static struct clk *ux500_twocell_get(struct of_phandle_args *clkspec,
 	return PRCC_SHOW(clk_data, base, bit);
 }
 
-static const struct of_device_id u8500_clk_of_match[] = {
-	{ .compatible = "stericsson,u8500-clks", },
-	{ },
-};
-
 /* CLKRST4 is missing making it hard to index things */
 enum clkrst_index {
 	CLKRST1_INDEX = 0,
@@ -63,22 +57,15 @@ enum clkrst_index {
 	CLKRST_MAX,
 };
 
-void u8500_clk_init(void)
+static void u8500_clk_init(struct device_node *np)
 {
 	struct prcmu_fw_version *fw_version;
-	struct device_node *np = NULL;
 	struct device_node *child = NULL;
 	const char *sgaclk_parent = NULL;
 	struct clk *clk, *rtc_clk, *twd_clk;
 	u32 bases[CLKRST_MAX];
 	int i;
 
-	if (of_have_populated_dt())
-		np = of_find_matching_node(NULL, u8500_clk_of_match);
-	if (!np) {
-		pr_err("Either DT or U8500 Clock node not found\n");
-		return;
-	}
 	for (i = 0; i < ARRAY_SIZE(bases); i++) {
 		struct resource r;
 
@@ -573,3 +560,4 @@ void u8500_clk_init(void)
 			of_clk_add_provider(child, of_clk_src_simple_get, twd_clk);
 	}
 }
+CLK_OF_DECLARE(u8500_clks, "stericsson,u8500-clks", u8500_clk_init);

drivers/clk/ux500/u8540_clk.c

@@ -12,14 +12,8 @@
 #include <linux/clkdev.h>
 #include <linux/clk-provider.h>
 #include <linux/mfd/dbx500-prcmu.h>
-#include <linux/platform_data/clk-ux500.h>
 #include "clk.h"
 
-static const struct of_device_id u8540_clk_of_match[] = {
-	{ .compatible = "stericsson,u8540-clks", },
-	{ }
-};
-
 /* CLKRST4 is missing making it hard to index things */
 enum clkrst_index {
 	CLKRST1_INDEX = 0,
@@ -30,19 +24,12 @@ enum clkrst_index {
 	CLKRST_MAX,
 };
 
-void u8540_clk_init(void)
+static void u8540_clk_init(struct device_node *np)
 {
 	struct clk *clk;
-	struct device_node *np = NULL;
 	u32 bases[CLKRST_MAX];
 	int i;
 
-	if (of_have_populated_dt())
-		np = of_find_matching_node(NULL, u8540_clk_of_match);
-	if (!np) {
-		pr_err("Either DT or U8540 Clock node not found\n");
-		return;
-	}
 	for (i = 0; i < ARRAY_SIZE(bases); i++) {
 		struct resource r;
 
@@ -607,3 +594,4 @@ void u8540_clk_init(void)
 			bases[CLKRST6_INDEX], BIT(0), CLK_SET_RATE_GATE);
 	clk_register_clkdev(clk, NULL, "rng");
 }
+CLK_OF_DECLARE(u8540_clks, "stericsson,u8540-clks", u8540_clk_init);

drivers/clk/ux500/u9540_clk.c

@@ -9,10 +9,10 @@
 
 #include <linux/clk-provider.h>
 #include <linux/mfd/dbx500-prcmu.h>
-#include <linux/platform_data/clk-ux500.h>
 #include "clk.h"
 
-void u9540_clk_init(void)
+static void u9540_clk_init(struct device_node *np)
 {
 	/* register clocks here */
 }
+CLK_OF_DECLARE(u9540_clks, "stericsson,u9540-clks", u9540_clk_init);

drivers/clocksource/clps711x-timer.c

@@ -119,5 +119,5 @@ static int __init clps711x_timer_init(struct device_node *np)
 		return -EINVAL;
 	}
 }
-CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,clps711x-timer", clps711x_timer_init);
+CLOCKSOURCE_OF_DECLARE(clps711x, "cirrus,ep7209-timer", clps711x_timer_init);
 #endif

drivers/cpufreq/s5pv210-cpufreq.c

@@ -220,7 +220,7 @@ static void s5pv210_set_refresh(enum s5pv210_dmc_port ch, unsigned long freq)
 
 	tmp1 /= tmp;
 
-	__raw_writel(tmp1, reg);
+	writel_relaxed(tmp1, reg);
 }
 
 static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
@@ -296,29 +296,29 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 		 * 1. Temporary Change divider for MFC and G3D
 		 * SCLKA2M(200/1=200)->(200/4=50)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_DIV2);
+		reg = readl_relaxed(S5P_CLK_DIV2);
 		reg &= ~(S5P_CLKDIV2_G3D_MASK | S5P_CLKDIV2_MFC_MASK);
 		reg |= (3 << S5P_CLKDIV2_G3D_SHIFT) |
 			(3 << S5P_CLKDIV2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV2);
+		writel_relaxed(reg, S5P_CLK_DIV2);
 
 		/* For MFC, G3D dividing */
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT0);
+			reg = readl_relaxed(S5P_CLKDIV_STAT0);
 		} while (reg & ((1 << 16) | (1 << 17)));
 
 		/*
 		 * 2. Change SCLKA2M(200Mhz)to SCLKMPLL in MFC_MUX, G3D MUX
 		 * (200/4=50)->(667/4=166)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_SRC2);
+		reg = readl_relaxed(S5P_CLK_SRC2);
 		reg &= ~(S5P_CLKSRC2_G3D_MASK | S5P_CLKSRC2_MFC_MASK);
 		reg |= (1 << S5P_CLKSRC2_G3D_SHIFT) |
 			(1 << S5P_CLKSRC2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC2);
+		writel_relaxed(reg, S5P_CLK_SRC2);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT1);
+			reg = readl_relaxed(S5P_CLKMUX_STAT1);
 		} while (reg & ((1 << 7) | (1 << 3)));
 
 		/*
@@ -330,19 +330,19 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 			s5pv210_set_refresh(DMC1, 133000);
 
 		/* 4. SCLKAPLL -> SCLKMPLL */
-		reg = __raw_readl(S5P_CLK_SRC0);
+		reg = readl_relaxed(S5P_CLK_SRC0);
 		reg &= ~(S5P_CLKSRC0_MUX200_MASK);
 		reg |= (0x1 << S5P_CLKSRC0_MUX200_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC0);
+		writel_relaxed(reg, S5P_CLK_SRC0);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT0);
+			reg = readl_relaxed(S5P_CLKMUX_STAT0);
 		} while (reg & (0x1 << 18));
 
 	}
 
 	/* Change divider */
-	reg = __raw_readl(S5P_CLK_DIV0);
+	reg = readl_relaxed(S5P_CLK_DIV0);
 
 	reg &= ~(S5P_CLKDIV0_APLL_MASK | S5P_CLKDIV0_A2M_MASK |
 		S5P_CLKDIV0_HCLK200_MASK | S5P_CLKDIV0_PCLK100_MASK |
@@ -358,25 +358,25 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 		(clkdiv_val[index][6] << S5P_CLKDIV0_HCLK133_SHIFT) |
 		(clkdiv_val[index][7] << S5P_CLKDIV0_PCLK66_SHIFT));
 
-	__raw_writel(reg, S5P_CLK_DIV0);
+	writel_relaxed(reg, S5P_CLK_DIV0);
 
 	do {
-		reg = __raw_readl(S5P_CLKDIV_STAT0);
+		reg = readl_relaxed(S5P_CLKDIV_STAT0);
 	} while (reg & 0xff);
 
 	/* ARM MCS value changed */
-	reg = __raw_readl(S5P_ARM_MCS_CON);
+	reg = readl_relaxed(S5P_ARM_MCS_CON);
 	reg &= ~0x3;
 	if (index >= L3)
 		reg |= 0x3;
 	else
 		reg |= 0x1;
 
-	__raw_writel(reg, S5P_ARM_MCS_CON);
+	writel_relaxed(reg, S5P_ARM_MCS_CON);
 
 	if (pll_changing) {
 		/* 5. Set Lock time = 30us*24Mhz = 0x2cf */
-		__raw_writel(0x2cf, S5P_APLL_LOCK);
+		writel_relaxed(0x2cf, S5P_APLL_LOCK);
 
 		/*
 		 * 6. Turn on APLL
@@ -384,12 +384,12 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 		 * 6-2. Wait untile the PLL is locked
 		 */
 		if (index == L0)
-			__raw_writel(APLL_VAL_1000, S5P_APLL_CON);
+			writel_relaxed(APLL_VAL_1000, S5P_APLL_CON);
 		else
-			__raw_writel(APLL_VAL_800, S5P_APLL_CON);
+			writel_relaxed(APLL_VAL_800, S5P_APLL_CON);
 
 		do {
-			reg = __raw_readl(S5P_APLL_CON);
+			reg = readl_relaxed(S5P_APLL_CON);
 		} while (!(reg & (0x1 << 29)));
 
 		/*
@@ -397,39 +397,39 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 		 * to SCLKA2M(200Mhz) in MFC_MUX and G3D MUX
 		 * (667/4=166)->(200/4=50)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_SRC2);
+		reg = readl_relaxed(S5P_CLK_SRC2);
 		reg &= ~(S5P_CLKSRC2_G3D_MASK | S5P_CLKSRC2_MFC_MASK);
 		reg |= (0 << S5P_CLKSRC2_G3D_SHIFT) |
 			(0 << S5P_CLKSRC2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC2);
+		writel_relaxed(reg, S5P_CLK_SRC2);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT1);
+			reg = readl_relaxed(S5P_CLKMUX_STAT1);
 		} while (reg & ((1 << 7) | (1 << 3)));
 
 		/*
 		 * 8. Change divider for MFC and G3D
 		 * (200/4=50)->(200/1=200)Mhz
 		 */
-		reg = __raw_readl(S5P_CLK_DIV2);
+		reg = readl_relaxed(S5P_CLK_DIV2);
 		reg &= ~(S5P_CLKDIV2_G3D_MASK | S5P_CLKDIV2_MFC_MASK);
 		reg |= (clkdiv_val[index][10] << S5P_CLKDIV2_G3D_SHIFT) |
 			(clkdiv_val[index][9] << S5P_CLKDIV2_MFC_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV2);
+		writel_relaxed(reg, S5P_CLK_DIV2);
 
 		/* For MFC, G3D dividing */
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT0);
+			reg = readl_relaxed(S5P_CLKDIV_STAT0);
 		} while (reg & ((1 << 16) | (1 << 17)));
 
 		/* 9. Change MPLL to APLL in MSYS_MUX */
-		reg = __raw_readl(S5P_CLK_SRC0);
+		reg = readl_relaxed(S5P_CLK_SRC0);
 		reg &= ~(S5P_CLKSRC0_MUX200_MASK);
 		reg |= (0x0 << S5P_CLKSRC0_MUX200_SHIFT);
-		__raw_writel(reg, S5P_CLK_SRC0);
+		writel_relaxed(reg, S5P_CLK_SRC0);
 
 		do {
-			reg = __raw_readl(S5P_CLKMUX_STAT0);
+			reg = readl_relaxed(S5P_CLKMUX_STAT0);
 		} while (reg & (0x1 << 18));
 
 		/*
@@ -446,13 +446,13 @@ static int s5pv210_target(struct cpufreq_policy *policy, unsigned int index)
 	 * and memory refresh parameter should be changed
 	 */
 	if (bus_speed_changing) {
-		reg = __raw_readl(S5P_CLK_DIV6);
+		reg = readl_relaxed(S5P_CLK_DIV6);
 		reg &= ~S5P_CLKDIV6_ONEDRAM_MASK;
 		reg |= (clkdiv_val[index][8] << S5P_CLKDIV6_ONEDRAM_SHIFT);
-		__raw_writel(reg, S5P_CLK_DIV6);
+		writel_relaxed(reg, S5P_CLK_DIV6);
 
 		do {
-			reg = __raw_readl(S5P_CLKDIV_STAT1);
+			reg = readl_relaxed(S5P_CLKDIV_STAT1);
 		} while (reg & (1 << 15));
 
 		/* Reconfigure DRAM refresh counter value */
@@ -492,7 +492,7 @@ static int check_mem_type(void __iomem *dmc_reg)
 {
 	unsigned long val;
 
-	val = __raw_readl(dmc_reg + 0x4);
+	val = readl_relaxed(dmc_reg + 0x4);
 	val = (val & (0xf << 8));
 
 	return val >> 8;
@@ -537,10 +537,10 @@ static int s5pv210_cpu_init(struct cpufreq_policy *policy)
 	}
 
 	/* Find current refresh counter and frequency each DMC */
-	s5pv210_dram_conf[0].refresh = (__raw_readl(dmc_base[0] + 0x30) * 1000);
+	s5pv210_dram_conf[0].refresh = (readl_relaxed(dmc_base[0] + 0x30) * 1000);
 	s5pv210_dram_conf[0].freq = clk_get_rate(dmc0_clk);
 
-	s5pv210_dram_conf[1].refresh = (__raw_readl(dmc_base[1] + 0x30) * 1000);
+	s5pv210_dram_conf[1].refresh = (readl_relaxed(dmc_base[1] + 0x30) * 1000);
 	s5pv210_dram_conf[1].freq = clk_get_rate(dmc1_clk);
 
 	policy->suspend_freq = SLEEP_FREQ;

drivers/firmware/Kconfig

@@ -10,7 +10,7 @@ config ARM_PSCI_FW
 
 config ARM_SCPI_PROTOCOL
 	tristate "ARM System Control and Power Interface (SCPI) Message Protocol"
-	depends on ARM_MHU
+	depends on MAILBOX
 	help
 	  System Control and Power Interface (SCPI) Message Protocol is
 	  defined for the purpose of communication between the Application
@@ -27,6 +27,15 @@ config ARM_SCPI_PROTOCOL
 	  This protocol library provides interface for all the client drivers
 	  making use of the features offered by the SCP.
 
+config ARM_SCPI_POWER_DOMAIN
+	tristate "SCPI power domain driver"
+	depends on ARM_SCPI_PROTOCOL || (COMPILE_TEST && OF)
+	default y
+	select PM_GENERIC_DOMAINS if PM
+	help
+	  This enables support for the SCPI power domains which can be
+	  enabled or disabled via the SCP firmware
+
 config EDD
 	tristate "BIOS Enhanced Disk Drive calls determine boot disk"
 	depends on X86
@@ -184,6 +193,7 @@ config FW_CFG_SYSFS_CMDLINE
 config QCOM_SCM
 	bool
 	depends on ARM || ARM64
+	select RESET_CONTROLLER
 
 config QCOM_SCM_32
 	def_bool y

drivers/firmware/Makefile

@@ -3,6 +3,7 @@
 #
 obj-$(CONFIG_ARM_PSCI_FW)	+= psci.o
 obj-$(CONFIG_ARM_SCPI_PROTOCOL)	+= arm_scpi.o
+obj-$(CONFIG_ARM_SCPI_POWER_DOMAIN) += scpi_pm_domain.o
 obj-$(CONFIG_DMI)		+= dmi_scan.o
 obj-$(CONFIG_DMI_SYSFS)		+= dmi-sysfs.o
 obj-$(CONFIG_EDD)		+= edd.o

drivers/firmware/arm_scpi.c

@@ -210,10 +210,6 @@ struct dvfs_info {
 	} opps[MAX_DVFS_OPPS];
 } __packed;
 
-struct dvfs_get {
-	u8 index;
-} __packed;
-
 struct dvfs_set {
 	u8 domain;
 	u8 index;
@@ -235,6 +231,11 @@ struct sensor_value {
 	__le32 hi_val;
 } __packed;
 
+struct dev_pstate_set {
+	u16 dev_id;
+	u8 pstate;
+} __packed;
+
 static struct scpi_drvinfo *scpi_info;
 
 static int scpi_linux_errmap[SCPI_ERR_MAX] = {
@@ -431,11 +432,11 @@ static int scpi_clk_set_val(u16 clk_id, unsigned long rate)
 static int scpi_dvfs_get_idx(u8 domain)
 {
 	int ret;
-	struct dvfs_get dvfs;
+	u8 dvfs_idx;
 
 	ret = scpi_send_message(SCPI_CMD_GET_DVFS, &domain, sizeof(domain),
-				&dvfs, sizeof(dvfs));
-	return ret ? ret : dvfs.index;
+				&dvfs_idx, sizeof(dvfs_idx));
+	return ret ? ret : dvfs_idx;
 }
 
 static int scpi_dvfs_set_idx(u8 domain, u8 index)
@@ -526,7 +527,7 @@ static int scpi_sensor_get_info(u16 sensor_id, struct scpi_sensor_info *info)
 	return ret;
 }
 
-int scpi_sensor_get_value(u16 sensor, u64 *val)
+static int scpi_sensor_get_value(u16 sensor, u64 *val)
 {
 	__le16 id = cpu_to_le16(sensor);
 	struct sensor_value buf;
@@ -541,6 +542,29 @@ int scpi_sensor_get_value(u16 sensor, u64 *val)
 	return ret;
 }
 
+static int scpi_device_get_power_state(u16 dev_id)
+{
+	int ret;
+	u8 pstate;
+	__le16 id = cpu_to_le16(dev_id);
+
+	ret = scpi_send_message(SCPI_CMD_GET_DEVICE_PWR_STATE, &id,
+				sizeof(id), &pstate, sizeof(pstate));
+	return ret ? ret : pstate;
+}
+
+static int scpi_device_set_power_state(u16 dev_id, u8 pstate)
+{
+	int stat;
+	struct dev_pstate_set dev_set = {
+		.dev_id = cpu_to_le16(dev_id),
+		.pstate = pstate,
+	};
+
+	return scpi_send_message(SCPI_CMD_SET_DEVICE_PWR_STATE, &dev_set,
+				 sizeof(dev_set), &stat, sizeof(stat));
+}
+
 static struct scpi_ops scpi_ops = {
 	.get_version = scpi_get_version,
 	.clk_get_range = scpi_clk_get_range,
@@ -552,6 +576,8 @@ static struct scpi_ops scpi_ops = {
 	.sensor_get_capability = scpi_sensor_get_capability,
 	.sensor_get_info = scpi_sensor_get_info,
 	.sensor_get_value = scpi_sensor_get_value,
+	.device_get_power_state = scpi_device_get_power_state,
+	.device_set_power_state = scpi_device_set_power_state,
 };
 
 struct scpi_ops *get_scpi_ops(void)

drivers/firmware/qcom_scm-64.c

@@ -12,7 +12,150 @@
 
 #include <linux/io.h>
 #include <linux/errno.h>
+#include <linux/delay.h>
+#include <linux/mutex.h>
+#include <linux/slab.h>
+#include <linux/types.h>
 #include <linux/qcom_scm.h>
+#include <linux/arm-smccc.h>
+#include <linux/dma-mapping.h>
+
+#include "qcom_scm.h"
+
+#define QCOM_SCM_FNID(s, c) ((((s) & 0xFF) << 8) | ((c) & 0xFF))
+
+#define MAX_QCOM_SCM_ARGS 10
+#define MAX_QCOM_SCM_RETS 3
+
+enum qcom_scm_arg_types {
+	QCOM_SCM_VAL,
+	QCOM_SCM_RO,
+	QCOM_SCM_RW,
+	QCOM_SCM_BUFVAL,
+};
+
+#define QCOM_SCM_ARGS_IMPL(num, a, b, c, d, e, f, g, h, i, j, ...) (\
+			   (((a) & 0x3) << 4) | \
+			   (((b) & 0x3) << 6) | \
+			   (((c) & 0x3) << 8) | \
+			   (((d) & 0x3) << 10) | \
+			   (((e) & 0x3) << 12) | \
+			   (((f) & 0x3) << 14) | \
+			   (((g) & 0x3) << 16) | \
+			   (((h) & 0x3) << 18) | \
+			   (((i) & 0x3) << 20) | \
+			   (((j) & 0x3) << 22) | \
+			   ((num) & 0xf))
+
+#define QCOM_SCM_ARGS(...) QCOM_SCM_ARGS_IMPL(__VA_ARGS__, 0, 0, 0, 0, 0, 0, 0, 0, 0, 0)
+
+/**
+ * struct qcom_scm_desc
+ * @arginfo:	Metadata describing the arguments in args[]
+ * @args:	The array of arguments for the secure syscall
+ * @res:	The values returned by the secure syscall
+ */
+struct qcom_scm_desc {
+	u32 arginfo;
+	u64 args[MAX_QCOM_SCM_ARGS];
+};
+
+static u64 qcom_smccc_convention = -1;
+static DEFINE_MUTEX(qcom_scm_lock);
+
+#define QCOM_SCM_EBUSY_WAIT_MS 30
+#define QCOM_SCM_EBUSY_MAX_RETRY 20
+
+#define N_EXT_QCOM_SCM_ARGS 7
+#define FIRST_EXT_ARG_IDX 3
+#define N_REGISTER_ARGS (MAX_QCOM_SCM_ARGS - N_EXT_QCOM_SCM_ARGS + 1)
+
+/**
+ * qcom_scm_call() - Invoke a syscall in the secure world
+ * @dev:	device
+ * @svc_id:	service identifier
+ * @cmd_id:	command identifier
+ * @desc:	Descriptor structure containing arguments and return values
+ *
+ * Sends a command to the SCM and waits for the command to finish processing.
+ * This should *only* be called in pre-emptible context.
+*/
+static int qcom_scm_call(struct device *dev, u32 svc_id, u32 cmd_id,
+			 const struct qcom_scm_desc *desc,
+			 struct arm_smccc_res *res)
+{
+	int arglen = desc->arginfo & 0xf;
+	int retry_count = 0, i;
+	u32 fn_id = QCOM_SCM_FNID(svc_id, cmd_id);
+	u64 cmd, x5 = desc->args[FIRST_EXT_ARG_IDX];
+	dma_addr_t args_phys = 0;
+	void *args_virt = NULL;
+	size_t alloc_len;
+
+	if (unlikely(arglen > N_REGISTER_ARGS)) {
+		alloc_len = N_EXT_QCOM_SCM_ARGS * sizeof(u64);
+		args_virt = kzalloc(PAGE_ALIGN(alloc_len), GFP_KERNEL);
+
+		if (!args_virt)
+			return -ENOMEM;
+
+		if (qcom_smccc_convention == ARM_SMCCC_SMC_32) {
+			__le32 *args = args_virt;
+
+			for (i = 0; i < N_EXT_QCOM_SCM_ARGS; i++)
+				args[i] = cpu_to_le32(desc->args[i +
+						      FIRST_EXT_ARG_IDX]);
+		} else {
+			__le64 *args = args_virt;
+
+			for (i = 0; i < N_EXT_QCOM_SCM_ARGS; i++)
+				args[i] = cpu_to_le64(desc->args[i +
+						      FIRST_EXT_ARG_IDX]);
+		}
+
+		args_phys = dma_map_single(dev, args_virt, alloc_len,
+					   DMA_TO_DEVICE);
+
+		if (dma_mapping_error(dev, args_phys)) {
+			kfree(args_virt);
+			return -ENOMEM;
+		}
+
+		x5 = args_phys;
+	}
+
+	do {
+		mutex_lock(&qcom_scm_lock);
+
+		cmd = ARM_SMCCC_CALL_VAL(ARM_SMCCC_STD_CALL,
+					 qcom_smccc_convention,
+					 ARM_SMCCC_OWNER_SIP, fn_id);
+
+		do {
+			arm_smccc_smc(cmd, desc->arginfo, desc->args[0],
+				      desc->args[1], desc->args[2], x5, 0, 0,
+				      res);
+		} while (res->a0 == QCOM_SCM_INTERRUPTED);
+
+		mutex_unlock(&qcom_scm_lock);
+
+		if (res->a0 == QCOM_SCM_V2_EBUSY) {
+			if (retry_count++ > QCOM_SCM_EBUSY_MAX_RETRY)
+				break;
+			msleep(QCOM_SCM_EBUSY_WAIT_MS);
+		}
+	}  while (res->a0 == QCOM_SCM_V2_EBUSY);
+
+	if (args_virt) {
+		dma_unmap_single(dev, args_phys, alloc_len, DMA_TO_DEVICE);
+		kfree(args_virt);
+	}
+
+	if (res->a0 < 0)
+		return qcom_scm_remap_error(res->a0);
+
+	return 0;
+}
 
 /**
  * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
@@ -29,13 +172,15 @@ int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus)
 
 /**
  * qcom_scm_set_warm_boot_addr() - Set the warm boot address for cpus
+ * @dev: Device pointer
  * @entry: Entry point function for the cpus
  * @cpus: The cpumask of cpus that will use the entry point
  *
  * Set the Linux entry point for the SCM to transfer control to when coming
  * out of a power down. CPU power down may be executed on cpuidle or hotplug.
  */
-int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
+int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
+				  const cpumask_t *cpus)
 {
 	return -ENOTSUPP;
 }
@@ -52,12 +197,164 @@ void __qcom_scm_cpu_power_down(u32 flags)
 {
 }
 
-int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id)
+int __qcom_scm_is_call_available(struct device *dev, u32 svc_id, u32 cmd_id)
 {
-	return -ENOTSUPP;
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.arginfo = QCOM_SCM_ARGS(1);
+	desc.args[0] = QCOM_SCM_FNID(svc_id, cmd_id) |
+			(ARM_SMCCC_OWNER_SIP << ARM_SMCCC_OWNER_SHIFT);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD,
+			    &desc, &res);
+
+	return ret ? : res.a1;
 }
 
-int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
+int __qcom_scm_hdcp_req(struct device *dev, struct qcom_scm_hdcp_req *req,
+			u32 req_cnt, u32 *resp)
 {
-	return -ENOTSUPP;
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	if (req_cnt > QCOM_SCM_HDCP_MAX_REQ_CNT)
+		return -ERANGE;
+
+	desc.args[0] = req[0].addr;
+	desc.args[1] = req[0].val;
+	desc.args[2] = req[1].addr;
+	desc.args[3] = req[1].val;
+	desc.args[4] = req[2].addr;
+	desc.args[5] = req[2].val;
+	desc.args[6] = req[3].addr;
+	desc.args[7] = req[3].val;
+	desc.args[8] = req[4].addr;
+	desc.args[9] = req[4].val;
+	desc.arginfo = QCOM_SCM_ARGS(10);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_HDCP, QCOM_SCM_CMD_HDCP, &desc,
+			    &res);
+	*resp = res.a1;
+
+	return ret;
+}
+
+void __qcom_scm_init(void)
+{
+	u64 cmd;
+	struct arm_smccc_res res;
+	u32 function = QCOM_SCM_FNID(QCOM_SCM_SVC_INFO, QCOM_IS_CALL_AVAIL_CMD);
+
+	/* First try a SMC64 call */
+	cmd = ARM_SMCCC_CALL_VAL(ARM_SMCCC_FAST_CALL, ARM_SMCCC_SMC_64,
+				 ARM_SMCCC_OWNER_SIP, function);
+
+	arm_smccc_smc(cmd, QCOM_SCM_ARGS(1), cmd & (~BIT(ARM_SMCCC_TYPE_SHIFT)),
+		      0, 0, 0, 0, 0, &res);
+
+	if (!res.a0 && res.a1)
+		qcom_smccc_convention = ARM_SMCCC_SMC_64;
+	else
+		qcom_smccc_convention = ARM_SMCCC_SMC_32;
+}
+
+bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+				QCOM_SCM_PAS_IS_SUPPORTED_CMD,
+				&desc, &res);
+
+	return ret ? false : !!res.a1;
+}
+
+int __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
+			      dma_addr_t metadata_phys)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.args[1] = metadata_phys;
+	desc.arginfo = QCOM_SCM_ARGS(2, QCOM_SCM_VAL, QCOM_SCM_RW);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_INIT_IMAGE_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
+			      phys_addr_t addr, phys_addr_t size)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.args[1] = addr;
+	desc.args[2] = size;
+	desc.arginfo = QCOM_SCM_ARGS(3);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_MEM_SETUP_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL,
+				QCOM_SCM_PAS_AUTH_AND_RESET_CMD,
+				&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral)
+{
+	int ret;
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+
+	desc.args[0] = peripheral;
+	desc.arginfo = QCOM_SCM_ARGS(1);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_SHUTDOWN_CMD,
+			&desc, &res);
+
+	return ret ? : res.a1;
+}
+
+int __qcom_scm_pas_mss_reset(struct device *dev, bool reset)
+{
+	struct qcom_scm_desc desc = {0};
+	struct arm_smccc_res res;
+	int ret;
+
+	desc.args[0] = reset;
+	desc.args[1] = 0;
+	desc.arginfo = QCOM_SCM_ARGS(2);
+
+	ret = qcom_scm_call(dev, QCOM_SCM_SVC_PIL, QCOM_SCM_PAS_MSS_RESET, &desc,
+			    &res);
+
+	return ret ? : res.a1;
 }

drivers/firmware/qcom_scm.c

@@ -10,19 +10,64 @@
  * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
  * GNU General Public License for more details.
  *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, write to the Free Software
- * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA
- * 02110-1301, USA.
  */
-
+#include <linux/platform_device.h>
+#include <linux/module.h>
 #include <linux/cpumask.h>
 #include <linux/export.h>
+#include <linux/dma-mapping.h>
 #include <linux/types.h>
 #include <linux/qcom_scm.h>
+#include <linux/of.h>
+#include <linux/of_platform.h>
+#include <linux/clk.h>
+#include <linux/reset-controller.h>
 
 #include "qcom_scm.h"
 
+struct qcom_scm {
+	struct device *dev;
+	struct clk *core_clk;
+	struct clk *iface_clk;
+	struct clk *bus_clk;
+	struct reset_controller_dev reset;
+};
+
+static struct qcom_scm *__scm;
+
+static int qcom_scm_clk_enable(void)
+{
+	int ret;
+
+	ret = clk_prepare_enable(__scm->core_clk);
+	if (ret)
+		goto bail;
+
+	ret = clk_prepare_enable(__scm->iface_clk);
+	if (ret)
+		goto disable_core;
+
+	ret = clk_prepare_enable(__scm->bus_clk);
+	if (ret)
+		goto disable_iface;
+
+	return 0;
+
+disable_iface:
+	clk_disable_unprepare(__scm->iface_clk);
+disable_core:
+	clk_disable_unprepare(__scm->core_clk);
+bail:
+	return ret;
+}
+
+static void qcom_scm_clk_disable(void)
+{
+	clk_disable_unprepare(__scm->core_clk);
+	clk_disable_unprepare(__scm->iface_clk);
+	clk_disable_unprepare(__scm->bus_clk);
+}
+
 /**
  * qcom_scm_set_cold_boot_addr() - Set the cold boot address for cpus
  * @entry: Entry point function for the cpus
@@ -47,7 +92,7 @@ EXPORT_SYMBOL(qcom_scm_set_cold_boot_addr);
  */
 int qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus)
 {
-	return __qcom_scm_set_warm_boot_addr(entry, cpus);
+	return __qcom_scm_set_warm_boot_addr(__scm->dev, entry, cpus);
 }
 EXPORT_SYMBOL(qcom_scm_set_warm_boot_addr);
 
@@ -72,12 +117,17 @@ EXPORT_SYMBOL(qcom_scm_cpu_power_down);
  */
 bool qcom_scm_hdcp_available(void)
 {
-	int ret;
+	int ret = qcom_scm_clk_enable();
 
-	ret = __qcom_scm_is_call_available(QCOM_SCM_SVC_HDCP,
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_HDCP,
 						QCOM_SCM_CMD_HDCP);
 
-	return (ret > 0) ? true : false;
+	qcom_scm_clk_disable();
+
+	return ret > 0 ? true : false;
 }
 EXPORT_SYMBOL(qcom_scm_hdcp_available);
 
@@ -91,6 +141,287 @@ EXPORT_SYMBOL(qcom_scm_hdcp_available);
  */
 int qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp)
 {
-	return __qcom_scm_hdcp_req(req, req_cnt, resp);
+	int ret = qcom_scm_clk_enable();
+
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_hdcp_req(__scm->dev, req, req_cnt, resp);
+	qcom_scm_clk_disable();
+	return ret;
 }
 EXPORT_SYMBOL(qcom_scm_hdcp_req);
+
+/**
+ * qcom_scm_pas_supported() - Check if the peripheral authentication service is
+ *			      available for the given peripherial
+ * @peripheral:	peripheral id
+ *
+ * Returns true if PAS is supported for this peripheral, otherwise false.
+ */
+bool qcom_scm_pas_supported(u32 peripheral)
+{
+	int ret;
+
+	ret = __qcom_scm_is_call_available(__scm->dev, QCOM_SCM_SVC_PIL,
+					   QCOM_SCM_PAS_IS_SUPPORTED_CMD);
+	if (ret <= 0)
+		return false;
+
+	return __qcom_scm_pas_supported(__scm->dev, peripheral);
+}
+EXPORT_SYMBOL(qcom_scm_pas_supported);
+
+/**
+ * qcom_scm_pas_init_image() - Initialize peripheral authentication service
+ *			       state machine for a given peripheral, using the
+ *			       metadata
+ * @peripheral: peripheral id
+ * @metadata:	pointer to memory containing ELF header, program header table
+ *		and optional blob of data used for authenticating the metadata
+ *		and the rest of the firmware
+ * @size:	size of the metadata
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_init_image(u32 peripheral, const void *metadata, size_t size)
+{
+	dma_addr_t mdata_phys;
+	void *mdata_buf;
+	int ret;
+
+	/*
+	 * During the scm call memory protection will be enabled for the meta
+	 * data blob, so make sure it's physically contiguous, 4K aligned and
+	 * non-cachable to avoid XPU violations.
+	 */
+	mdata_buf = dma_alloc_coherent(__scm->dev, size, &mdata_phys,
+				       GFP_KERNEL);
+	if (!mdata_buf) {
+		dev_err(__scm->dev, "Allocation of metadata buffer failed.\n");
+		return -ENOMEM;
+	}
+	memcpy(mdata_buf, metadata, size);
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		goto free_metadata;
+
+	ret = __qcom_scm_pas_init_image(__scm->dev, peripheral, mdata_phys);
+
+	qcom_scm_clk_disable();
+
+free_metadata:
+	dma_free_coherent(__scm->dev, size, mdata_buf, mdata_phys);
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_init_image);
+
+/**
+ * qcom_scm_pas_mem_setup() - Prepare the memory related to a given peripheral
+ *			      for firmware loading
+ * @peripheral:	peripheral id
+ * @addr:	start address of memory area to prepare
+ * @size:	size of the memory area to prepare
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_mem_setup(u32 peripheral, phys_addr_t addr, phys_addr_t size)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_mem_setup(__scm->dev, peripheral, addr, size);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_mem_setup);
+
+/**
+ * qcom_scm_pas_auth_and_reset() - Authenticate the given peripheral firmware
+ *				   and reset the remote processor
+ * @peripheral:	peripheral id
+ *
+ * Return 0 on success.
+ */
+int qcom_scm_pas_auth_and_reset(u32 peripheral)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_auth_and_reset(__scm->dev, peripheral);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_auth_and_reset);
+
+/**
+ * qcom_scm_pas_shutdown() - Shut down the remote processor
+ * @peripheral: peripheral id
+ *
+ * Returns 0 on success.
+ */
+int qcom_scm_pas_shutdown(u32 peripheral)
+{
+	int ret;
+
+	ret = qcom_scm_clk_enable();
+	if (ret)
+		return ret;
+
+	ret = __qcom_scm_pas_shutdown(__scm->dev, peripheral);
+	qcom_scm_clk_disable();
+
+	return ret;
+}
+EXPORT_SYMBOL(qcom_scm_pas_shutdown);
+
+static int qcom_scm_pas_reset_assert(struct reset_controller_dev *rcdev,
+				     unsigned long idx)
+{
+	if (idx != 0)
+		return -EINVAL;
+
+	return __qcom_scm_pas_mss_reset(__scm->dev, 1);
+}
+
+static int qcom_scm_pas_reset_deassert(struct reset_controller_dev *rcdev,
+				       unsigned long idx)
+{
+	if (idx != 0)
+		return -EINVAL;
+
+	return __qcom_scm_pas_mss_reset(__scm->dev, 0);
+}
+
+static const struct reset_control_ops qcom_scm_pas_reset_ops = {
+	.assert = qcom_scm_pas_reset_assert,
+	.deassert = qcom_scm_pas_reset_deassert,
+};
+
+/**
+ * qcom_scm_is_available() - Checks if SCM is available
+ */
+bool qcom_scm_is_available(void)
+{
+	return !!__scm;
+}
+EXPORT_SYMBOL(qcom_scm_is_available);
+
+static int qcom_scm_probe(struct platform_device *pdev)
+{
+	struct qcom_scm *scm;
+	int ret;
+
+	scm = devm_kzalloc(&pdev->dev, sizeof(*scm), GFP_KERNEL);
+	if (!scm)
+		return -ENOMEM;
+
+	scm->core_clk = devm_clk_get(&pdev->dev, "core");
+	if (IS_ERR(scm->core_clk)) {
+		if (PTR_ERR(scm->core_clk) == -EPROBE_DEFER)
+			return PTR_ERR(scm->core_clk);
+
+		scm->core_clk = NULL;
+	}
+
+	if (of_device_is_compatible(pdev->dev.of_node, "qcom,scm")) {
+		scm->iface_clk = devm_clk_get(&pdev->dev, "iface");
+		if (IS_ERR(scm->iface_clk)) {
+			if (PTR_ERR(scm->iface_clk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to acquire iface clk\n");
+			return PTR_ERR(scm->iface_clk);
+		}
+
+		scm->bus_clk = devm_clk_get(&pdev->dev, "bus");
+		if (IS_ERR(scm->bus_clk)) {
+			if (PTR_ERR(scm->bus_clk) != -EPROBE_DEFER)
+				dev_err(&pdev->dev, "failed to acquire bus clk\n");
+			return PTR_ERR(scm->bus_clk);
+		}
+	}
+
+	scm->reset.ops = &qcom_scm_pas_reset_ops;
+	scm->reset.nr_resets = 1;
+	scm->reset.of_node = pdev->dev.of_node;
+	reset_controller_register(&scm->reset);
+
+	/* vote for max clk rate for highest performance */
+	ret = clk_set_rate(scm->core_clk, INT_MAX);
+	if (ret)
+		return ret;
+
+	__scm = scm;
+	__scm->dev = &pdev->dev;
+
+	__qcom_scm_init();
+
+	return 0;
+}
+
+static const struct of_device_id qcom_scm_dt_match[] = {
+	{ .compatible = "qcom,scm-apq8064",},
+	{ .compatible = "qcom,scm-msm8660",},
+	{ .compatible = "qcom,scm-msm8960",},
+	{ .compatible = "qcom,scm",},
+	{}
+};
+
+MODULE_DEVICE_TABLE(of, qcom_scm_dt_match);
+
+static struct platform_driver qcom_scm_driver = {
+	.driver = {
+		.name	= "qcom_scm",
+		.of_match_table = qcom_scm_dt_match,
+	},
+	.probe = qcom_scm_probe,
+};
+
+static int __init qcom_scm_init(void)
+{
+	struct device_node *np, *fw_np;
+	int ret;
+
+	fw_np = of_find_node_by_name(NULL, "firmware");
+
+	if (!fw_np)
+		return -ENODEV;
+
+	np = of_find_matching_node(fw_np, qcom_scm_dt_match);
+
+	if (!np) {
+		of_node_put(fw_np);
+		return -ENODEV;
+	}
+
+	of_node_put(np);
+
+	ret = of_platform_populate(fw_np, qcom_scm_dt_match, NULL, NULL);
+
+	of_node_put(fw_np);
+
+	if (ret)
+		return ret;
+
+	return platform_driver_register(&qcom_scm_driver);
+}
+
+subsys_initcall(qcom_scm_init);
+
+static void __exit qcom_scm_exit(void)
+{
+	platform_driver_unregister(&qcom_scm_driver);
+}
+module_exit(qcom_scm_exit);
+
+MODULE_DESCRIPTION("Qualcomm SCM driver");
+MODULE_LICENSE("GPL v2");

drivers/firmware/qcom_scm.h

@@ -19,7 +19,8 @@
 #define QCOM_SCM_FLAG_HLOS		0x01
 #define QCOM_SCM_FLAG_COLDBOOT_MC	0x02
 #define QCOM_SCM_FLAG_WARMBOOT_MC	0x04
-extern int __qcom_scm_set_warm_boot_addr(void *entry, const cpumask_t *cpus);
+extern int __qcom_scm_set_warm_boot_addr(struct device *dev, void *entry,
+		const cpumask_t *cpus);
 extern int __qcom_scm_set_cold_boot_addr(void *entry, const cpumask_t *cpus);
 
 #define QCOM_SCM_CMD_TERMINATE_PC	0x2
@@ -29,14 +30,34 @@ extern void __qcom_scm_cpu_power_down(u32 flags);
 
 #define QCOM_SCM_SVC_INFO		0x6
 #define QCOM_IS_CALL_AVAIL_CMD		0x1
-extern int __qcom_scm_is_call_available(u32 svc_id, u32 cmd_id);
+extern int __qcom_scm_is_call_available(struct device *dev, u32 svc_id,
+		u32 cmd_id);
 
 #define QCOM_SCM_SVC_HDCP		0x11
 #define QCOM_SCM_CMD_HDCP		0x01
-extern int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt,
-		u32 *resp);
+extern int __qcom_scm_hdcp_req(struct device *dev,
+		struct qcom_scm_hdcp_req *req, u32 req_cnt, u32 *resp);
+
+extern void __qcom_scm_init(void);
+
+#define QCOM_SCM_SVC_PIL		0x2
+#define QCOM_SCM_PAS_INIT_IMAGE_CMD	0x1
+#define QCOM_SCM_PAS_MEM_SETUP_CMD	0x2
+#define QCOM_SCM_PAS_AUTH_AND_RESET_CMD	0x5
+#define QCOM_SCM_PAS_SHUTDOWN_CMD	0x6
+#define QCOM_SCM_PAS_IS_SUPPORTED_CMD	0x7
+#define QCOM_SCM_PAS_MSS_RESET		0xa
+extern bool __qcom_scm_pas_supported(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_init_image(struct device *dev, u32 peripheral,
+		dma_addr_t metadata_phys);
+extern int  __qcom_scm_pas_mem_setup(struct device *dev, u32 peripheral,
+		phys_addr_t addr, phys_addr_t size);
+extern int  __qcom_scm_pas_auth_and_reset(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_shutdown(struct device *dev, u32 peripheral);
+extern int  __qcom_scm_pas_mss_reset(struct device *dev, bool reset);
 
 /* common error codes */
+#define QCOM_SCM_V2_EBUSY	-12
 #define QCOM_SCM_ENOMEM		-5
 #define QCOM_SCM_EOPNOTSUPP	-4
 #define QCOM_SCM_EINVAL_ADDR	-3
@@ -44,4 +65,22 @@ extern int __qcom_scm_hdcp_req(struct qcom_scm_hdcp_req *req, u32 req_cnt,
 #define QCOM_SCM_ERROR		-1
 #define QCOM_SCM_INTERRUPTED	1
 
+static inline int qcom_scm_remap_error(int err)
+{
+	switch (err) {
+	case QCOM_SCM_ERROR:
+		return -EIO;
+	case QCOM_SCM_EINVAL_ADDR:
+	case QCOM_SCM_EINVAL_ARG:
+		return -EINVAL;
+	case QCOM_SCM_EOPNOTSUPP:
+		return -EOPNOTSUPP;
+	case QCOM_SCM_ENOMEM:
+		return -ENOMEM;
+	case QCOM_SCM_V2_EBUSY:
+		return -EBUSY;
+	}
+	return -EINVAL;
+}
+
 #endif

drivers/firmware/scpi_pm_domain.c

+/*
+ * SCPI Generic power domain support.
+ *
+ * Copyright (C) 2016 ARM Ltd.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms and conditions of the GNU General Public License,
+ * version 2, as published by the Free Software Foundation.
+ *
+ * This program is distributed in the hope it will be useful, but WITHOUT
+ * ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
+ * FITNESS FOR A PARTICULAR PURPOSE. See the GNU General Public License for
+ * more details.
+ *
+ * You should have received a copy of the GNU General Public License along
+ * with this program. If not, see <http://www.gnu.org/licenses/>.
+ */
+
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of_platform.h>
+#include <linux/pm_domain.h>
+#include <linux/scpi_protocol.h>
+
+struct scpi_pm_domain {
+	struct generic_pm_domain genpd;
+	struct scpi_ops *ops;
+	u32 domain;
+	char name[30];
+};
+
+/*
+ * These device power state values are not well-defined in the specification.
+ * In case, different implementations use different values, we can make these
+ * specific to compatibles rather than getting these values from device tree.
+ */
+enum scpi_power_domain_state {
+	SCPI_PD_STATE_ON = 0,
+	SCPI_PD_STATE_OFF = 3,
+};
+
+#define to_scpi_pd(gpd) container_of(gpd, struct scpi_pm_domain, genpd)
+
+static int scpi_pd_power(struct scpi_pm_domain *pd, bool power_on)
+{
+	int ret;
+	enum scpi_power_domain_state state;
+
+	if (power_on)
+		state = SCPI_PD_STATE_ON;
+	else
+		state = SCPI_PD_STATE_OFF;
+
+	ret = pd->ops->device_set_power_state(pd->domain, state);
+	if (ret)
+		return ret;
+
+	return !(state == pd->ops->device_get_power_state(pd->domain));
+}
+
+static int scpi_pd_power_on(struct generic_pm_domain *domain)
+{
+	struct scpi_pm_domain *pd = to_scpi_pd(domain);
+
+	return scpi_pd_power(pd, true);
+}
+
+static int scpi_pd_power_off(struct generic_pm_domain *domain)
+{
+	struct scpi_pm_domain *pd = to_scpi_pd(domain);
+
+	return scpi_pd_power(pd, false);
+}
+
+static int scpi_pm_domain_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct device_node *np = dev->of_node;
+	struct scpi_pm_domain *scpi_pd;
+	struct genpd_onecell_data *scpi_pd_data;
+	struct generic_pm_domain **domains;
+	struct scpi_ops *scpi_ops;
+	int ret, num_domains, i;
+
+	scpi_ops = get_scpi_ops();
+	if (!scpi_ops)
+		return -EPROBE_DEFER;
+
+	if (!np) {
+		dev_err(dev, "device tree node not found\n");
+		return -ENODEV;
+	}
+
+	if (!scpi_ops->device_set_power_state ||
+	    !scpi_ops->device_get_power_state) {
+		dev_err(dev, "power domains not supported in the firmware\n");
+		return -ENODEV;
+	}
+
+	ret = of_property_read_u32(np, "num-domains", &num_domains);
+	if (ret) {
+		dev_err(dev, "number of domains not found\n");
+		return -EINVAL;
+	}
+
+	scpi_pd = devm_kcalloc(dev, num_domains, sizeof(*scpi_pd), GFP_KERNEL);
+	if (!scpi_pd)
+		return -ENOMEM;
+
+	scpi_pd_data = devm_kzalloc(dev, sizeof(*scpi_pd_data), GFP_KERNEL);
+	if (!scpi_pd_data)
+		return -ENOMEM;
+
+	domains = devm_kcalloc(dev, num_domains, sizeof(*domains), GFP_KERNEL);
+	if (!domains)
+		return -ENOMEM;
+
+	for (i = 0; i < num_domains; i++, scpi_pd++) {
+		domains[i] = &scpi_pd->genpd;
+
+		scpi_pd->domain = i;
+		scpi_pd->ops = scpi_ops;
+		sprintf(scpi_pd->name, "%s.%d", np->name, i);
+		scpi_pd->genpd.name = scpi_pd->name;
+		scpi_pd->genpd.power_off = scpi_pd_power_off;
+		scpi_pd->genpd.power_on = scpi_pd_power_on;
+
+		/*
+		 * Treat all power domains as off at boot.
+		 *
+		 * The SCP firmware itself may have switched on some domains,
+		 * but for reference counting purpose, keep it this way.
+		 */
+		pm_genpd_init(&scpi_pd->genpd, NULL, true);
+	}
+
+	scpi_pd_data->domains = domains;
+	scpi_pd_data->num_domains = num_domains;
+
+	of_genpd_add_provider_onecell(np, scpi_pd_data);
+
+	return 0;
+}
+
+static const struct of_device_id scpi_power_domain_ids[] = {
+	{ .compatible = "arm,scpi-power-domains", },
+	{ /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, scpi_power_domain_ids);
+
+static struct platform_driver scpi_power_domain_driver = {
+	.driver	= {
+		.name = "scpi_power_domain",
+		.of_match_table = scpi_power_domain_ids,
+	},
+	.probe = scpi_pm_domain_probe,
+};
+module_platform_driver(scpi_power_domain_driver);
+
+MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
+MODULE_DESCRIPTION("ARM SCPI power domain driver");
+MODULE_LICENSE("GPL v2");

drivers/input/keyboard/clps711x-keypad.c

@@ -101,7 +101,7 @@ static int clps711x_keypad_probe(struct platform_device *pdev)
 		return -ENOMEM;
 
 	priv->syscon =
-		syscon_regmap_lookup_by_compatible("cirrus,clps711x-syscon1");
+		syscon_regmap_lookup_by_compatible("cirrus,ep7209-syscon1");
 	if (IS_ERR(priv->syscon))
 		return PTR_ERR(priv->syscon);
 
@@ -181,7 +181,7 @@ static int clps711x_keypad_remove(struct platform_device *pdev)
 }
 
 static const struct of_device_id clps711x_keypad_of_match[] = {
-	{ .compatible = "cirrus,clps711x-keypad", },
+	{ .compatible = "cirrus,ep7209-keypad", },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, clps711x_keypad_of_match);

drivers/irqchip/irq-clps711x.c

@@ -234,5 +234,5 @@ static int __init clps711x_intc_init_dt(struct device_node *np,
 
 	return _clps711x_intc_init(np, res.start, resource_size(&res));
 }
-IRQCHIP_DECLARE(clps711x, "cirrus,clps711x-intc", clps711x_intc_init_dt);
+IRQCHIP_DECLARE(clps711x, "cirrus,ep7209-intc", clps711x_intc_init_dt);
 #endif

drivers/media/rc/Kconfig

@@ -336,7 +336,7 @@ config IR_TTUSBIR
 
 config IR_RX51
 	tristate "Nokia N900 IR transmitter diode"
-	depends on OMAP_DM_TIMER && ARCH_OMAP2PLUS && LIRC && !ARCH_MULTIPLATFORM
+	depends on OMAP_DM_TIMER && PWM_OMAP_DMTIMER && ARCH_OMAP2PLUS && LIRC
 	---help---
 	   Say Y or M here if you want to enable support for the IR
 	   transmitter diode built in the Nokia N900 (RX51) device.

drivers/memory/Kconfig

@@ -25,6 +25,17 @@ config ATMEL_SDRAMC
 	  Starting with the at91sam9g45, this controller supports SDR, DDR and
 	  LP-DDR memories.
 
+config ATMEL_EBI
+	bool "Atmel EBI driver"
+	default y
+	depends on ARCH_AT91 && OF
+	select MFD_SYSCON
+	help
+	  Driver for Atmel EBI controller.
+	  Used to configure the EBI (external bus interface) when the device-
+	  tree is used. This bus supports NANDs, external ethernet controller,
+	  SRAMs, ATA devices, etc.
+
 config TI_AEMIF
 	tristate "Texas Instruments AEMIF driver"
 	depends on (ARCH_DAVINCI || ARCH_KEYSTONE) && OF

drivers/memory/Makefile

@@ -7,6 +7,7 @@ obj-$(CONFIG_OF)		+= of_memory.o
 endif
 obj-$(CONFIG_ARM_PL172_MPMC)	+= pl172.o
 obj-$(CONFIG_ATMEL_SDRAMC)	+= atmel-sdramc.o
+obj-$(CONFIG_ATMEL_EBI)		+= atmel-ebi.o
 obj-$(CONFIG_TI_AEMIF)		+= ti-aemif.o
 obj-$(CONFIG_TI_EMIF)		+= emif.o
 obj-$(CONFIG_OMAP_GPMC)		+= omap-gpmc.o

drivers/memory/atmel-sdramc.c

 /*
  * Atmel (Multi-port DDR-)SDRAM Controller driver
  *
+ * Author: Alexandre Belloni <alexandre.belloni@free-electrons.com>
+ *
  * Copyright (C) 2014 Atmel
  *
  * This program is free software: you can redistribute it and/or modify
@@ -20,7 +22,7 @@
 #include <linux/clk.h>
 #include <linux/err.h>
 #include <linux/kernel.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/of_platform.h>
 #include <linux/platform_device.h>
 
@@ -48,7 +50,6 @@ static const struct of_device_id atmel_ramc_of_match[] = {
 	{ .compatible = "atmel,sama5d3-ddramc", .data = &sama5d3_caps, },
 	{},
 };
-MODULE_DEVICE_TABLE(of, atmel_ramc_of_match);
 
 static int atmel_ramc_probe(struct platform_device *pdev)
 {
@@ -90,8 +91,4 @@ static int __init atmel_ramc_init(void)
 {
 	return platform_driver_register(&atmel_ramc_driver);
 }
-module_init(atmel_ramc_init);
-
-MODULE_LICENSE("GPL v2");
-MODULE_AUTHOR("Alexandre Belloni <alexandre.belloni@free-electrons.com>");
-MODULE_DESCRIPTION("Atmel (Multi-port DDR-)SDRAM Controller");
+device_initcall(atmel_ramc_init);

drivers/memory/omap-gpmc.c

@@ -20,7 +20,6 @@
 #include <linux/ioport.h>
 #include <linux/spinlock.h>
 #include <linux/io.h>
-#include <linux/module.h>
 #include <linux/gpio/driver.h>
 #include <linux/interrupt.h>
 #include <linux/irqdomain.h>
@@ -1807,7 +1806,6 @@ static const struct of_device_id gpmc_dt_ids[] = {
 	{ .compatible = "ti,am3352-gpmc" },	/* am335x devices */
 	{ }
 };
-MODULE_DEVICE_TABLE(of, gpmc_dt_ids);
 
 /**
  * gpmc_read_settings_dt - read gpmc settings from device-tree
@@ -2154,68 +2152,6 @@ static int gpmc_probe_generic_child(struct platform_device *pdev,
 	return ret;
 }
 
-static int gpmc_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
-{
-	return 1;	/* we're input only */
-}
-
-static int gpmc_gpio_direction_input(struct gpio_chip *chip,
-				     unsigned int offset)
-{
-	return 0;	/* we're input only */
-}
-
-static int gpmc_gpio_direction_output(struct gpio_chip *chip,
-				      unsigned int offset, int value)
-{
-	return -EINVAL;	/* we're input only */
-}
-
-static void gpmc_gpio_set(struct gpio_chip *chip, unsigned int offset,
-			  int value)
-{
-}
-
-static int gpmc_gpio_get(struct gpio_chip *chip, unsigned int offset)
-{
-	u32 reg;
-
-	offset += 8;
-
-	reg = gpmc_read_reg(GPMC_STATUS) & BIT(offset);
-
-	return !!reg;
-}
-
-static int gpmc_gpio_init(struct gpmc_device *gpmc)
-{
-	int ret;
-
-	gpmc->gpio_chip.parent = gpmc->dev;
-	gpmc->gpio_chip.owner = THIS_MODULE;
-	gpmc->gpio_chip.label = DEVICE_NAME;
-	gpmc->gpio_chip.ngpio = gpmc_nr_waitpins;
-	gpmc->gpio_chip.get_direction = gpmc_gpio_get_direction;
-	gpmc->gpio_chip.direction_input = gpmc_gpio_direction_input;
-	gpmc->gpio_chip.direction_output = gpmc_gpio_direction_output;
-	gpmc->gpio_chip.set = gpmc_gpio_set;
-	gpmc->gpio_chip.get = gpmc_gpio_get;
-	gpmc->gpio_chip.base = -1;
-
-	ret = gpiochip_add(&gpmc->gpio_chip);
-	if (ret < 0) {
-		dev_err(gpmc->dev, "could not register gpio chip: %d\n", ret);
-		return ret;
-	}
-
-	return 0;
-}
-
-static void gpmc_gpio_exit(struct gpmc_device *gpmc)
-{
-	gpiochip_remove(&gpmc->gpio_chip);
-}
-
 static int gpmc_probe_dt(struct platform_device *pdev)
 {
 	int ret;
@@ -2280,7 +2216,69 @@ static int gpmc_probe_dt_children(struct platform_device *pdev)
 {
 	return 0;
 }
-#endif
+#endif /* CONFIG_OF */
+
+static int gpmc_gpio_get_direction(struct gpio_chip *chip, unsigned int offset)
+{
+	return 1;	/* we're input only */
+}
+
+static int gpmc_gpio_direction_input(struct gpio_chip *chip,
+				     unsigned int offset)
+{
+	return 0;	/* we're input only */
+}
+
+static int gpmc_gpio_direction_output(struct gpio_chip *chip,
+				      unsigned int offset, int value)
+{
+	return -EINVAL;	/* we're input only */
+}
+
+static void gpmc_gpio_set(struct gpio_chip *chip, unsigned int offset,
+			  int value)
+{
+}
+
+static int gpmc_gpio_get(struct gpio_chip *chip, unsigned int offset)
+{
+	u32 reg;
+
+	offset += 8;
+
+	reg = gpmc_read_reg(GPMC_STATUS) & BIT(offset);
+
+	return !!reg;
+}
+
+static int gpmc_gpio_init(struct gpmc_device *gpmc)
+{
+	int ret;
+
+	gpmc->gpio_chip.parent = gpmc->dev;
+	gpmc->gpio_chip.owner = THIS_MODULE;
+	gpmc->gpio_chip.label = DEVICE_NAME;
+	gpmc->gpio_chip.ngpio = gpmc_nr_waitpins;
+	gpmc->gpio_chip.get_direction = gpmc_gpio_get_direction;
+	gpmc->gpio_chip.direction_input = gpmc_gpio_direction_input;
+	gpmc->gpio_chip.direction_output = gpmc_gpio_direction_output;
+	gpmc->gpio_chip.set = gpmc_gpio_set;
+	gpmc->gpio_chip.get = gpmc_gpio_get;
+	gpmc->gpio_chip.base = -1;
+
+	ret = gpiochip_add(&gpmc->gpio_chip);
+	if (ret < 0) {
+		dev_err(gpmc->dev, "could not register gpio chip: %d\n", ret);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void gpmc_gpio_exit(struct gpmc_device *gpmc)
+{
+	gpiochip_remove(&gpmc->gpio_chip);
+}
 
 static int gpmc_probe(struct platform_device *pdev)
 {
@@ -2436,15 +2434,7 @@ static __init int gpmc_init(void)
 {
 	return platform_driver_register(&gpmc_driver);
 }
-
-static __exit void gpmc_exit(void)
-{
-	platform_driver_unregister(&gpmc_driver);
-
-}
-
 postcore_initcall(gpmc_init);
-module_exit(gpmc_exit);
 
 static struct omap3_gpmc_regs gpmc_context;
 

drivers/memory/samsung/exynos-srom.c

@@ -11,7 +11,7 @@
  */
 
 #include <linux/io.h>
-#include <linux/module.h>
+#include <linux/init.h>
 #include <linux/of.h>
 #include <linux/of_address.h>
 #include <linux/of_platform.h>
@@ -91,11 +91,11 @@ static int exynos_srom_configure_bank(struct exynos_srom *srom,
 	if (width == 2)
 		cs |= 1 << EXYNOS_SROM_BW__DATAWIDTH__SHIFT;
 
-	bw = __raw_readl(srom->reg_base + EXYNOS_SROM_BW);
+	bw = readl_relaxed(srom->reg_base + EXYNOS_SROM_BW);
 	bw = (bw & ~(EXYNOS_SROM_BW__CS_MASK << bank)) | (cs << bank);
-	__raw_writel(bw, srom->reg_base + EXYNOS_SROM_BW);
+	writel_relaxed(bw, srom->reg_base + EXYNOS_SROM_BW);
 
-	__raw_writel(pmc | (timing[0] << EXYNOS_SROM_BCX__TACP__SHIFT) |
+	writel_relaxed(pmc | (timing[0] << EXYNOS_SROM_BCX__TACP__SHIFT) |
 		       (timing[1] << EXYNOS_SROM_BCX__TCAH__SHIFT) |
 		       (timing[2] << EXYNOS_SROM_BCX__TCOH__SHIFT) |
 		       (timing[3] << EXYNOS_SROM_BCX__TACC__SHIFT) |
@@ -134,7 +134,7 @@ static int exynos_srom_probe(struct platform_device *pdev)
 	platform_set_drvdata(pdev, srom);
 
 	srom->reg_offset = exynos_srom_alloc_reg_dump(exynos_srom_offsets,
-			sizeof(exynos_srom_offsets));
+			ARRAY_SIZE(exynos_srom_offsets));
 	if (!srom->reg_offset) {
 		iounmap(srom->reg_base);
 		return -ENOMEM;
@@ -159,16 +159,6 @@ static int exynos_srom_probe(struct platform_device *pdev)
 	return of_platform_populate(np, NULL, NULL, dev);
 }
 
-static int exynos_srom_remove(struct platform_device *pdev)
-{
-	struct exynos_srom *srom = platform_get_drvdata(pdev);
-
-	kfree(srom->reg_offset);
-	iounmap(srom->reg_base);
-
-	return 0;
-}
-
 #ifdef CONFIG_PM_SLEEP
 static void exynos_srom_save(void __iomem *base,
 				    struct exynos_srom_reg_dump *rd,
@@ -211,21 +201,16 @@ static const struct of_device_id of_exynos_srom_ids[] = {
 	},
 	{},
 };
-MODULE_DEVICE_TABLE(of, of_exynos_srom_ids);
 
 static SIMPLE_DEV_PM_OPS(exynos_srom_pm_ops, exynos_srom_suspend, exynos_srom_resume);
 
 static struct platform_driver exynos_srom_driver = {
 	.probe = exynos_srom_probe,
-	.remove = exynos_srom_remove,
 	.driver = {
 		.name = "exynos-srom",
 		.of_match_table = of_exynos_srom_ids,
 		.pm = &exynos_srom_pm_ops,
+		.suppress_bind_attrs = true,
 	},
 };
-module_platform_driver(exynos_srom_driver);
-
-MODULE_AUTHOR("Pankaj Dubey <pankaj.dubey@samsung.com>");
-MODULE_DESCRIPTION("Exynos SROM Controller Driver");
-MODULE_LICENSE("GPL");
+builtin_platform_driver(exynos_srom_driver);

drivers/mfd/ab8500-core.c

@@ -1087,7 +1087,6 @@ static int ab8500_probe(struct platform_device *pdev)
 		"Vbus Detect (USB)",
 		"USB ID Detect",
 		"UART Factory Mode Detect"};
-	struct ab8500_platform_data *plat = dev_get_platdata(&pdev->dev);
 	const struct platform_device_id *platid = platform_get_device_id(pdev);
 	enum ab8500_version version = AB8500_VERSION_UNDEFINED;
 	struct device_node *np = pdev->dev.of_node;
@@ -1219,9 +1218,6 @@ static int ab8500_probe(struct platform_device *pdev)
 		pr_cont("None\n");
 	}
 
-	if (plat && plat->init)
-		plat->init(ab8500);
-
 	if (is_ab9540(ab8500)) {
 		ret = get_register_interruptible(ab8500, AB8500_CHARGER,
 			AB8500_CH_USBCH_STAT1_REG, &value);