ARM: OMAP2: Change 24xx to use new register access

This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.

Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.

The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.

Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

arch/arm/mach-omap2/board-2430sdp.c

@@ -33,7 +33,6 @@
 #include <asm/arch/board.h>
 #include <asm/arch/common.h>
 #include <asm/arch/gpmc.h>
-#include "prcm-regs.h"
 
 #include <asm/io.h>
 
@@ -125,15 +124,18 @@ static inline void __init sdp2430_init_smc91x(void)
 	int eth_cs;
 	unsigned long cs_mem_base;
 	unsigned int rate;
-	struct clk *l3ck;
+	struct clk *gpmc_fck;
 
 	eth_cs = SDP2430_SMC91X_CS;
 
-	l3ck = clk_get(NULL, "core_l3_ck");
-	if (IS_ERR(l3ck))
-		rate = 100000000;
-	else
-		rate = clk_get_rate(l3ck);
+	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
+	if (IS_ERR(gpmc_fck)) {
+		WARN_ON(1);
+		return;
+	}
+
+	clk_enable(gpmc_fck);
+	rate = clk_get_rate(gpmc_fck);
 
 	/* Make sure CS1 timings are correct, for 2430 always muxed */
 	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
@@ -160,7 +162,7 @@ static inline void __init sdp2430_init_smc91x(void)
 
 	if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
 		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
-		return;
+		goto out;
 	}
 
 	sdp2430_smc91x_resources[0].start = cs_mem_base + 0x300;
@@ -171,10 +173,13 @@ static inline void __init sdp2430_init_smc91x(void)
 		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
 			OMAP24XX_ETHR_GPIO_IRQ);
 		gpmc_cs_free(eth_cs);
-		return;
+		goto out;
 	}
 	omap_set_gpio_direction(OMAP24XX_ETHR_GPIO_IRQ, 1);
 
+out:
+	clk_disable(gpmc_fck);
+	clk_put(gpmc_fck);
 }
 
 static void __init omap_2430sdp_init_irq(void)

arch/arm/mach-omap2/board-apollon.c

@@ -26,6 +26,8 @@
 #include <linux/interrupt.h>
 #include <linux/delay.h>
 #include <linux/leds.h>
+#include <linux/err.h>
+#include <linux/clk.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>
@@ -39,7 +41,7 @@
 #include <asm/arch/board.h>
 #include <asm/arch/common.h>
 #include <asm/arch/gpmc.h>
-#include "prcm-regs.h"
+#include <asm/arch/control.h>
 
 /* LED & Switch macros */
 #define LED0_GPIO13		13
@@ -187,17 +189,47 @@ static inline void __init apollon_init_smc91x(void)
 {
 	unsigned long base;
 
+	unsigned int rate;
+	struct clk *gpmc_fck;
+	int eth_cs;
+
+	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
+	if (IS_ERR(gpmc_fck)) {
+		WARN_ON(1);
+		return;
+	}
+
+	clk_enable(gpmc_fck);
+	rate = clk_get_rate(gpmc_fck);
+
+	eth_cs = APOLLON_ETH_CS;
+
 	/* Make sure CS1 timings are correct */
-	GPMC_CONFIG1_1 = 0x00011203;
-	GPMC_CONFIG2_1 = 0x001f1f01;
-	GPMC_CONFIG3_1 = 0x00080803;
-	GPMC_CONFIG4_1 = 0x1c091c09;
-	GPMC_CONFIG5_1 = 0x041f1f1f;
-	GPMC_CONFIG6_1 = 0x000004c4;
+	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1, 0x00011200);
+
+	if (rate >= 160000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else if (rate >= 130000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else {/* rate = 100000000 */
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+	}
 
 	if (gpmc_cs_request(APOLLON_ETH_CS, SZ_16M, &base) < 0) {
 		printk(KERN_ERR "Failed to request GPMC CS for smc91x\n");
-		return;
+		goto out;
 	}
 	apollon_smc91x_resources[0].start = base + 0x300;
 	apollon_smc91x_resources[0].end   = base + 0x30f;
@@ -208,9 +240,13 @@ static inline void __init apollon_init_smc91x(void)
 		printk(KERN_ERR "Failed to request GPIO%d for smc91x IRQ\n",
 			APOLLON_ETHR_GPIO_IRQ);
 		gpmc_cs_free(APOLLON_ETH_CS);
-		return;
+		goto out;
 	}
 	omap_set_gpio_direction(APOLLON_ETHR_GPIO_IRQ, 1);
+
+out:
+	clk_disable(gpmc_fck);
+	clk_put(gpmc_fck);
 }
 
 static void __init omap_apollon_init_irq(void)
@@ -330,6 +366,8 @@ static void __init apollon_usb_init(void)
 
 static void __init omap_apollon_init(void)
 {
+	u32 v;
+
 	apollon_led_init();
 	apollon_sw_init();
 	apollon_flash_init();
@@ -339,7 +377,9 @@ static void __init omap_apollon_init(void)
 	omap_cfg_reg(W19_24XX_SYS_NIRQ);
 
 	/* Use Interal loop-back in MMC/SDIO Module Input Clock selection */
-	CONTROL_DEVCONF |= (1 << 24);
+	v = omap_ctrl_readl(OMAP2_CONTROL_DEVCONF0);
+	v |= (1 << 24);
+	omap_ctrl_writel(v, OMAP2_CONTROL_DEVCONF0);
 
 	/*
  	 * Make sure the serial ports are muxed on at this point.

arch/arm/mach-omap2/board-h4.c

@@ -19,6 +19,8 @@
 #include <linux/delay.h>
 #include <linux/workqueue.h>
 #include <linux/input.h>
+#include <linux/err.h>
+#include <linux/clk.h>
 
 #include <asm/hardware.h>
 #include <asm/mach-types.h>
@@ -26,6 +28,7 @@
 #include <asm/mach/map.h>
 #include <asm/mach/flash.h>
 
+#include <asm/arch/control.h>
 #include <asm/arch/gpio.h>
 #include <asm/arch/gpioexpander.h>
 #include <asm/arch/mux.h>
@@ -36,10 +39,13 @@
 #include <asm/arch/keypad.h>
 #include <asm/arch/menelaus.h>
 #include <asm/arch/dma.h>
-#include "prcm-regs.h"
+#include <asm/arch/gpmc.h>
 
 #include <asm/io.h>
 
+#define H4_FLASH_CS	0
+#define H4_SMC91X_CS	1
+
 static unsigned int row_gpios[6] = { 88, 89, 124, 11, 6, 96 };
 static unsigned int col_gpios[7] = { 90, 91, 100, 36, 12, 97, 98 };
 
@@ -116,8 +122,6 @@ static struct flash_platform_data h4_flash_data = {
 };
 
 static struct resource h4_flash_resource = {
-	.start		= H4_CS0_BASE,
-	.end		= H4_CS0_BASE + SZ_64M - 1,
 	.flags		= IORESOURCE_MEM,
 };
 
@@ -253,21 +257,107 @@ static struct platform_device *h4_devices[] __initdata = {
 	&h4_lcd_device,
 };
 
+/* 2420 Sysboot setup (2430 is different) */
+static u32 get_sysboot_value(void)
+{
+	return (omap_ctrl_readl(OMAP24XX_CONTROL_STATUS) &
+		(OMAP2_SYSBOOT_5_MASK | OMAP2_SYSBOOT_4_MASK |
+		 OMAP2_SYSBOOT_3_MASK | OMAP2_SYSBOOT_2_MASK |
+		 OMAP2_SYSBOOT_1_MASK | OMAP2_SYSBOOT_0_MASK));
+}
+
+/* H4-2420's always used muxed mode, H4-2422's always use non-muxed
+ *
+ * Note: OMAP-GIT doesn't correctly do is_cpu_omap2422 and is_cpu_omap2423
+ *  correctly.  The macro needs to look at production_id not just hawkeye.
+ */
+static u32 is_gpmc_muxed(void)
+{
+	u32 mux;
+	mux = get_sysboot_value();
+	if ((mux & 0xF) == 0xd)
+		return 1;	/* NAND config (could be either) */
+	if (mux & 0x2)		/* if mux'ed */
+		return 1;
+	else
+		return 0;
+}
+
 static inline void __init h4_init_debug(void)
 {
+	int eth_cs;
+	unsigned long cs_mem_base;
+	unsigned int muxed, rate;
+	struct clk *gpmc_fck;
+
+	eth_cs	= H4_SMC91X_CS;
+
+	gpmc_fck = clk_get(NULL, "gpmc_fck");	/* Always on ENABLE_ON_INIT */
+	if (IS_ERR(gpmc_fck)) {
+		WARN_ON(1);
+		return;
+	}
+
+	clk_enable(gpmc_fck);
+	rate = clk_get_rate(gpmc_fck);
+	clk_disable(gpmc_fck);
+	clk_put(gpmc_fck);
+
+	if (is_gpmc_muxed())
+		muxed = 0x200;
+	else
+		muxed = 0;
+
 	/* Make sure CS1 timings are correct */
-	GPMC_CONFIG1_1 = 0x00011200;
-	GPMC_CONFIG2_1 = 0x001f1f01;
-	GPMC_CONFIG3_1 = 0x00080803;
-	GPMC_CONFIG4_1 = 0x1c091c09;
-	GPMC_CONFIG5_1 = 0x041f1f1f;
-	GPMC_CONFIG6_1 = 0x000004c4;
-	GPMC_CONFIG7_1 = 0x00000f40 | (0x08000000 >> 24);
+	gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG1,
+			  0x00011000 | muxed);
+
+	if (rate >= 160000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f01);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080803);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1c0b1c0a);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else if (rate >= 130000000) {
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x041f1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000004C4);
+	} else {/* rate = 100000000 */
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG2, 0x001f1f00);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG3, 0x00080802);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG4, 0x1C091C09);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG5, 0x031A1F1F);
+		gpmc_cs_write_reg(eth_cs, GPMC_CS_CONFIG6, 0x000003C2);
+	}
+
+	if (gpmc_cs_request(eth_cs, SZ_16M, &cs_mem_base) < 0) {
+		printk(KERN_ERR "Failed to request GPMC mem for smc91x\n");
+		goto out;
+	}
+
 	udelay(100);
 
 	omap_cfg_reg(M15_24XX_GPIO92);
 	if (debug_card_init(cs_mem_base, OMAP24XX_ETHR_GPIO_IRQ) < 0)
 		gpmc_cs_free(eth_cs);
+
+out:
+	clk_disable(gpmc_fck);
+	clk_put(gpmc_fck);
+}
+
+static void __init h4_init_flash(void)
+{
+	unsigned long base;
+
+	if (gpmc_cs_request(H4_FLASH_CS, SZ_64M, &base) < 0) {
+		printk("Can't request GPMC CS for flash\n");
+		return;
+	}
+	h4_flash_resource.start	= base;
+	h4_flash_resource.end	= base + SZ_64M - 1;
 }
 
 static void __init omap_h4_init_irq(void)
@@ -275,6 +365,7 @@ static void __init omap_h4_init_irq(void)
 	omap2_init_common_hw();
 	omap_init_irq();
 	omap_gpio_init();
+	h4_init_flash();
 }
 
 static struct omap_uart_config h4_uart_config __initdata = {

arch/arm/mach-omap2/gpmc.c

@@ -69,7 +69,7 @@ static void __iomem *gpmc_base =
 static void __iomem *gpmc_cs_base =
 	(void __iomem *) IO_ADDRESS(GPMC_BASE) + GPMC_CS0;
 
-static struct clk *gpmc_l3_clk;
+static struct clk *gpmc_fck;
 
 static void gpmc_write_reg(int idx, u32 val)
 {
@@ -94,11 +94,10 @@ u32 gpmc_cs_read_reg(int cs, int idx)
 	return __raw_readl(gpmc_cs_base + (cs * GPMC_CS_SIZE) + idx);
 }
 
-/* TODO: Add support for gpmc_fck to clock framework and use it */
 unsigned long gpmc_get_fclk_period(void)
 {
 	/* In picoseconds */
-	return 1000000000 / ((clk_get_rate(gpmc_l3_clk)) / 1000);
+	return 1000000000 / ((clk_get_rate(gpmc_fck)) / 1000);
 }
 
 unsigned int gpmc_ns_to_ticks(unsigned int time_ns)
@@ -398,8 +397,11 @@ void __init gpmc_init(void)
 {
 	u32 l;
 
-	gpmc_l3_clk = clk_get(NULL, "core_l3_ck");
-	BUG_ON(IS_ERR(gpmc_l3_clk));
+	gpmc_fck = clk_get(NULL, "gpmc_fck"); /* Always on ENABLE_ON_INIT */
+	if (IS_ERR(gpmc_fck))
+		WARN_ON(1);
+	else
+		clk_enable(gpmc_fck);
 
 	l = gpmc_read_reg(GPMC_REVISION);
 	printk(KERN_INFO "GPMC revision %d.%d\n", (l >> 4) & 0x0f, l & 0x0f);

arch/arm/mach-omap2/memory.c

@@ -27,11 +27,16 @@
 #include <asm/arch/clock.h>
 #include <asm/arch/sram.h>
 
-#include "prcm-regs.h"
+#include "prm.h"
+
 #include "memory.h"
+#include "sdrc.h"
 
+unsigned long omap2_sdrc_base;
+unsigned long omap2_sms_base;
 
 static struct memory_timings mem_timings;
+static u32 curr_perf_level = CORE_CLK_SRC_DPLL_X2;
 
 u32 omap2_memory_get_slow_dll_ctrl(void)
 {
@@ -53,7 +58,7 @@ void omap2_init_memory_params(u32 force_lock_to_unlock_mode)
 	unsigned long dll_cnt;
 	u32 fast_dll = 0;
 
-	mem_timings.m_type = !((SDRC_MR_0 & 0x3) == 0x1); /* DDR = 1, SDR = 0 */
+	mem_timings.m_type = !((sdrc_read_reg(SDRC_MR_0) & 0x3) == 0x1); /* DDR = 1, SDR = 0 */
 
 	/* 2422 es2.05 and beyond has a single SIP DDR instead of 2 like others.
 	 * In the case of 2422, its ok to use CS1 instead of CS0.
@@ -73,11 +78,11 @@ void omap2_init_memory_params(u32 force_lock_to_unlock_mode)
 		mem_timings.dll_mode = M_LOCK;
 
 	if (mem_timings.base_cs == 0) {
-		fast_dll = SDRC_DLLA_CTRL;
-		dll_cnt = SDRC_DLLA_STATUS & 0xff00;
+		fast_dll = sdrc_read_reg(SDRC_DLLA_CTRL);
+		dll_cnt = sdrc_read_reg(SDRC_DLLA_STATUS) & 0xff00;
 	} else {
-		fast_dll = SDRC_DLLB_CTRL;
-		dll_cnt = SDRC_DLLB_STATUS & 0xff00;
+		fast_dll = sdrc_read_reg(SDRC_DLLB_CTRL);
+		dll_cnt = sdrc_read_reg(SDRC_DLLB_STATUS) & 0xff00;
 	}
 	if (force_lock_to_unlock_mode) {
 		fast_dll &= ~0xff00;
@@ -106,14 +111,13 @@ void __init omap2_init_memory(void)
 {
 	u32 l;
 
-	l = SMS_SYSCONFIG;
+	l = sms_read_reg(SMS_SYSCONFIG);
 	l &= ~(0x3 << 3);
 	l |= (0x2 << 3);
-	SMS_SYSCONFIG = l;
+	sms_write_reg(l, SMS_SYSCONFIG);
 
-	l = SDRC_SYSCONFIG;
+	l = sdrc_read_reg(SDRC_SYSCONFIG);
 	l &= ~(0x3 << 3);
 	l |= (0x2 << 3);
-	SDRC_SYSCONFIG = l;
-
+	sdrc_write_reg(l, SDRC_SYSCONFIG);
 }

arch/arm/mach-omap2/mux.c

@@ -29,6 +29,7 @@
 #include <asm/io.h>
 #include <linux/spinlock.h>
 
+#include <asm/arch/control.h>
 #include <asm/arch/mux.h>
 
 #ifdef CONFIG_OMAP_MUX
@@ -218,18 +219,16 @@ MUX_CFG_24XX("AD13_2430_MCBSP2_DR_OFF",	0x0131,	0,	0,	0,	1)
 #define OMAP24XX_PINS_SZ	0
 #endif	/* CONFIG_ARCH_OMAP24XX */
 
-#define OMAP24XX_L4_BASE	0x48000000
 #define OMAP24XX_PULL_ENA	(1 << 3)
 #define OMAP24XX_PULL_UP	(1 << 4)
 
-/* REVISIT: Convert this code to use ctrl_{read,write}_reg */
 #if defined(CONFIG_OMAP_MUX_DEBUG) || defined(CONFIG_OMAP_MUX_WARNINGS)
 void __init_or_module omap2_cfg_debug(const struct pin_config *cfg, u8 reg)
 {
 	u16 orig;
 	u8 warn = 0, debug = 0;
 
-	orig = omap_readb(OMAP24XX_L4_BASE + cfg->mux_reg);
+	orig = omap_ctrl_readb(cfg->mux_reg);
 
 #ifdef	CONFIG_OMAP_MUX_DEBUG
 	debug = cfg->debug;
@@ -238,7 +237,8 @@ void __init_or_module omap2_cfg_debug(const struct pin_config *cfg, u8 reg)
 	if (debug || warn)
 		printk(KERN_WARNING
 			"MUX: setup %s (0x%08x): 0x%02x -> 0x%02x\n",
-			cfg->name, omap_readb(OMAP24XX_L4_BASE + cfg->mux_reg));
+			cfg->name, omap_ctrl_base_get() + cfg->mux_reg,
+			orig, reg);
 }
 #else
 #define omap2_cfg_debug(x, y)	do {} while (0)
@@ -258,7 +258,7 @@ int __init_or_module omap24xx_cfg_reg(const struct pin_config *cfg)
 	if (cfg->pu_pd_val)
 		reg |= OMAP24XX_PULL_UP;
 	omap2_cfg_debug(cfg, reg);
-	omap_writeb(reg, OMAP24XX_L4_BASE + cfg->mux_reg);
+	omap_ctrl_writeb(reg, cfg->mux_reg);
 	spin_unlock_irqrestore(&mux_spin_lock, flags);
 
 	return 0;

arch/arm/mach-omap2/prcm-regs.h

@@ -23,6 +23,20 @@
 #ifndef __ARCH_ARM_MACH_OMAP2_PRCM_H
 #define __ARCH_ARM_MACH_OMAP2_PRCM_H
 
+#ifdef CONFIG_ARCH_OMAP2420
+#define OMAP24XX_32KSYNCT_BASE	(L4_24XX_BASE + 0x4000)
+#define OMAP24XX_PRCM_BASE	(L4_24XX_BASE + 0x8000)
+#define OMAP24XX_SDRC_BASE	(L3_24XX_BASE + 0x9000)
+#define OMAP242X_CONTROL_STATUS	(L4_24XX_BASE + 0x2f8)
+#endif
+
+#ifdef CONFIG_ARCH_OMAP2430
+#define OMAP24XX_32KSYNCT_BASE (L4_WK_243X_BASE + 0x20000)
+#define OMAP24XX_PRCM_BASE     (L4_WK_243X_BASE + 0x6000)
+#define OMAP24XX_SDRC_BASE     (0x6D000000)
+#define OMAP242X_CONTROL_STATUS        (L4_24XX_BASE + 0x2f8)
+#endif
+
 /* SET_PERFORMANCE_LEVEL PARAMETERS */
 #define PRCM_HALF_SPEED 1
 #define PRCM_FULL_SPEED 2

arch/arm/mach-omap2/prcm.c

@@ -17,19 +17,27 @@
 #include <linux/init.h>
 #include <linux/clk.h>
 
-#include "prcm-regs.h"
+#include <asm/io.h>
+
+#include "prm.h"
+#include "prm-regbits-24xx.h"
 
 extern void omap2_clk_prepare_for_reboot(void);
 
 u32 omap_prcm_get_reset_sources(void)
 {
-	return RM_RSTST_WKUP & 0x7f;
+	return prm_read_mod_reg(WKUP_MOD, RM_RSTST) & 0x7f;
 }
 EXPORT_SYMBOL(omap_prcm_get_reset_sources);
 
 /* Resets clock rates and reboots the system. Only called from system.h */
 void omap_prcm_arch_reset(char mode)
 {
+	u32 wkup;
 	omap2_clk_prepare_for_reboot();
-	RM_RSTCTRL_WKUP |= 2;
+
+	if (cpu_is_omap24xx()) {
+		wkup = prm_read_mod_reg(WKUP_MOD, RM_RSTCTRL) | OMAP_RST_DPLL3;
+		prm_write_mod_reg(wkup, WKUP_MOD, RM_RSTCTRL);
+	}
 }

arch/arm/mach-omap2/sleep.S

@@ -26,19 +26,10 @@
 #include <asm/arch/io.h>
 #include <asm/arch/pm.h>
 
-#define A_32KSYNC_CR_V		IO_ADDRESS(OMAP_TIMER32K_BASE+0x10)
-#define A_PRCM_VOLTCTRL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x50)
-#define A_PRCM_CLKCFG_CTRL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x80)
-#define A_CM_CLKEN_PLL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x500)
-#define A_CM_IDLEST_CKGEN_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x520)
-#define A_CM_CLKSEL1_PLL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x540)
-#define A_CM_CLKSEL2_PLL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE+0x544)
+#include "sdrc.h"
 
-#define A_SDRC_DLLA_CTRL_V	IO_ADDRESS(OMAP24XX_SDRC_BASE+0x60)
-#define	A_SDRC_POWER_V		IO_ADDRESS(OMAP24XX_SDRC_BASE+0x70)
-#define A_SDRC_RFR_CTRL_V	IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA4)
+/* First address of reserved address space?  apparently valid for OMAP2 & 3 */
 #define A_SDRC0_V		(0xC0000000)
-#define A_SDRC_MANUAL_V		IO_ADDRESS(OMAP24XX_SDRC_BASE+0xA8)
 
 	.text
 
@@ -126,17 +117,11 @@ loop2:
 	ldmfd	sp!, {r0 - r12, pc}	@ restore regs and return
 
 A_SDRC_POWER:
-	.word A_SDRC_POWER_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_POWER)
 A_SDRC0:
 	.word A_SDRC0_V
-A_CM_CLKSEL2_PLL_S:
-	.word A_CM_CLKSEL2_PLL_V
-A_CM_CLKEN_PLL:
-	.word A_CM_CLKEN_PLL_V
 A_SDRC_DLLA_CTRL_S:
-	.word A_SDRC_DLLA_CTRL_V
-A_SDRC_MANUAL_S:
-	.word A_SDRC_MANUAL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
 
 ENTRY(omap24xx_cpu_suspend_sz)
 	.word	. - omap24xx_cpu_suspend

arch/arm/mach-omap2/sram-fn.S

@@ -27,19 +27,11 @@
 #include <asm/arch/io.h>
 #include <asm/hardware.h>
 
-#include "prcm-regs.h"
+#include "sdrc.h"
+#include "prm.h"
+#include "cm.h"
 
-#define TIMER_32KSYNCT_CR_V	IO_ADDRESS(OMAP24XX_32KSYNCT_BASE + 0x010)
-
-#define CM_CLKSEL2_PLL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x544)
-#define PRCM_VOLTCTRL_V		IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x050)
-#define PRCM_CLKCFG_CTRL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x080)
-#define CM_CLKEN_PLL_V		IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x500)
-#define CM_IDLEST_CKGEN_V	IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x520)
-#define CM_CLKSEL1_PLL_V	IO_ADDRESS(OMAP24XX_PRCM_BASE + 0x540)
-
-#define SDRC_DLLA_CTRL_V	IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x060)
-#define SDRC_RFR_CTRL_V		IO_ADDRESS(OMAP24XX_SDRC_BASE + 0x0a4)
+#define TIMER_32KSYNCT_CR_V	IO_ADDRESS(OMAP2420_32KSYNCT_BASE + 0x010)
 
 	.text
 
@@ -131,11 +123,11 @@ volt_delay:
 
 /* relative load constants */
 cm_clksel2_pll:
-	.word CM_CLKSEL2_PLL_V
+	.word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
 sdrc_dlla_ctrl:
-	.word SDRC_DLLA_CTRL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
 prcm_voltctrl:
-	.word PRCM_VOLTCTRL_V
+	.word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
 prcm_mask_val:
 	.word 0xFFFF3FFC
 timer_32ksynct_cr:
@@ -225,13 +217,13 @@ volt_delay_c:
 	mov	pc, lr			@ back to caller
 
 ddr_cm_clksel2_pll:
-	.word CM_CLKSEL2_PLL_V
+	.word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL2)
 ddr_sdrc_dlla_ctrl:
-	.word SDRC_DLLA_CTRL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
 ddr_sdrc_rfr_ctrl:
-	.word SDRC_RFR_CTRL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
 ddr_prcm_voltctrl:
-	.word PRCM_VOLTCTRL_V
+	.word OMAP2420_PRM_REGADDR(OCP_MOD, 0x50)
 ddr_prcm_mask_val:
 	.word 0xFFFF3FFC
 ddr_timer_32ksynct:
@@ -316,17 +308,17 @@ wait_dll_lock:
 	ldmfd	sp!, {r0-r12, pc}	@ restore regs and return
 
 set_config:
-	.word PRCM_CLKCFG_CTRL_V
+	.word OMAP2420_PRM_REGADDR(OCP_MOD, 0x80)
 pll_ctl:
-	.word CM_CLKEN_PLL_V
+	.word OMAP2420_CM_REGADDR(PLL_MOD, CM_FCLKEN1)
 pll_stat:
-	.word CM_IDLEST_CKGEN_V
+	.word OMAP2420_CM_REGADDR(PLL_MOD, CM_IDLEST1)
 pll_div:
-	.word CM_CLKSEL1_PLL_V
+	.word OMAP2420_CM_REGADDR(PLL_MOD, CM_CLKSEL)
 sdrc_rfr:
-	.word SDRC_RFR_CTRL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_RFR_CTRL_0)
 dlla_ctrl:
-	.word SDRC_DLLA_CTRL_V
+	.word OMAP242X_SDRC_REGADDR(SDRC_DLLA_CTRL)
 
 ENTRY(sram_set_prcm_sz)
 	.word	. - sram_set_prcm

arch/arm/plat-omap/common.c

@@ -27,11 +27,16 @@
 #include <asm/setup.h>
 
 #include <asm/arch/board.h>
+#include <asm/arch/control.h>
 #include <asm/arch/mux.h>
 #include <asm/arch/fpga.h>
 
 #include <asm/arch/clock.h>
 
+#if defined(CONFIG_ARCH_OMAP2) || defined(CONFIG_ARCH_OMAP3)
+# include "../mach-omap2/sdrc.h"
+#endif
+
 #define NO_LENGTH_CHECK 0xffffffff
 
 unsigned char omap_bootloader_tag[512];
@@ -171,8 +176,8 @@ console_initcall(omap_add_serial_console);
 
 #if defined(CONFIG_ARCH_OMAP16XX)
 #define TIMER_32K_SYNCHRONIZED		0xfffbc410
-#elif defined(CONFIG_ARCH_OMAP24XX)
-#define TIMER_32K_SYNCHRONIZED		(OMAP24XX_32KSYNCT_BASE + 0x10)
+#elif defined(CONFIG_ARCH_OMAP24XX) || defined(CONFIG_ARCH_OMAP34XX)
+#define TIMER_32K_SYNCHRONIZED		(OMAP2_32KSYNCT_BASE + 0x10)
 #endif
 
 #ifdef	TIMER_32K_SYNCHRONIZED
@@ -215,7 +220,13 @@ static int __init omap_init_clocksource_32k(void)
 	static char err[] __initdata = KERN_ERR
 			"%s: can't register clocksource!\n";
 
-	if (cpu_is_omap16xx() || cpu_is_omap24xx()) {
+	if (cpu_is_omap16xx() || cpu_class_is_omap2()) {
+		struct clk *sync_32k_ick;
+
+		sync_32k_ick = clk_get(NULL, "omap_32ksync_ick");
+		if (sync_32k_ick)
+			clk_enable(sync_32k_ick);
+
 		clocksource_32k.mult = clocksource_hz2mult(32768,
 					    clocksource_32k.shift);
 
@@ -227,3 +238,33 @@ static int __init omap_init_clocksource_32k(void)
 arch_initcall(omap_init_clocksource_32k);
 
 #endif	/* TIMER_32K_SYNCHRONIZED */
+
+/* Global address base setup code */
+
+#if defined(CONFIG_ARCH_OMAP2420)
+void __init omap2_set_globals_242x(void)
+{
+	omap2_sdrc_base = OMAP2420_SDRC_BASE;
+	omap2_sms_base = OMAP2420_SMS_BASE;
+	omap_ctrl_base_set(OMAP2420_CTRL_BASE);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP2430)
+void __init omap2_set_globals_243x(void)
+{
+	omap2_sdrc_base = OMAP243X_SDRC_BASE;
+	omap2_sms_base = OMAP243X_SMS_BASE;
+	omap_ctrl_base_set(OMAP243X_CTRL_BASE);
+}
+#endif
+
+#if defined(CONFIG_ARCH_OMAP3430)
+void __init omap2_set_globals_343x(void)
+{
+	omap2_sdrc_base = OMAP343X_SDRC_BASE;
+	omap2_sms_base = OMAP343X_SMS_BASE;
+	omap_ctrl_base_set(OMAP343X_CTRL_BASE);
+}
+#endif
+

include/asm-arm/arch-omap/clock.h

@@ -88,4 +88,9 @@ extern int clk_get_usecount(struct clk *clk);
 #define CLOCK_IN_OMAP242X	(1 << 25)
 #define CLOCK_IN_OMAP243X	(1 << 26)
 
+/* CM_CLKSEL2_PLL.CORE_CLK_SRC options (24XX) */
+#define CORE_CLK_SRC_32K		0
+#define CORE_CLK_SRC_DPLL		1
+#define CORE_CLK_SRC_DPLL_X2		2
+
 #endif

include/asm-arm/arch-omap/entry-macro.S

@@ -68,7 +68,7 @@
 		.endm
 
 		.macro	get_irqnr_and_base, irqnr, irqstat, base, tmp
-		ldr	\base, =VA_IC_BASE
+		ldr	\base, =OMAP2_VA_IC_BASE
 		ldr	\irqnr, [\base, #0x98] /* IRQ pending reg 1 */
 		cmp	\irqnr, #0x0
 		bne	2222f

include/asm-arm/arch-omap/io.h

@@ -80,6 +80,13 @@
 #define OMAP243X_GPMC_PHYS	OMAP243X_GPMC_BASE	/* 0x49000000 */
 #define OMAP243X_GPMC_VIRT	0xFE000000
 #define OMAP243X_GPMC_SIZE	SZ_1M
+#define OMAP243X_SDRC_PHYS	OMAP243X_SDRC_BASE
+#define OMAP243X_SDRC_VIRT	0xFD000000
+#define OMAP243X_SDRC_SIZE	SZ_1M
+#define OMAP243X_SMS_PHYS	OMAP243X_SMS_BASE
+#define OMAP243X_SMS_VIRT	0xFC000000
+#define OMAP243X_SMS_SIZE	SZ_1M
+
 #endif
 
 #define IO_OFFSET	0x90000000
@@ -88,16 +95,73 @@
 #define io_v2p(va)	((va) - IO_OFFSET)	/* Works for L3 and L4 */
 
 /* DSP */
-#define DSP_MEM_24XX_PHYS	OMAP24XX_DSP_MEM_BASE	/* 0x58000000 */
+#define DSP_MEM_24XX_PHYS	OMAP2420_DSP_MEM_BASE	/* 0x58000000 */
 #define DSP_MEM_24XX_VIRT	0xe0000000
 #define DSP_MEM_24XX_SIZE	0x28000
-#define DSP_IPI_24XX_PHYS	OMAP24XX_DSP_IPI_BASE	/* 0x59000000 */
+#define DSP_IPI_24XX_PHYS	OMAP2420_DSP_IPI_BASE	/* 0x59000000 */
 #define DSP_IPI_24XX_VIRT	0xe1000000
 #define DSP_IPI_24XX_SIZE	SZ_4K
-#define DSP_MMU_24XX_PHYS	OMAP24XX_DSP_MMU_BASE	/* 0x5a000000 */
+#define DSP_MMU_24XX_PHYS	OMAP2420_DSP_MMU_BASE	/* 0x5a000000 */
 #define DSP_MMU_24XX_VIRT	0xe2000000
 #define DSP_MMU_24XX_SIZE	SZ_4K
 
+#elif defined(CONFIG_ARCH_OMAP3)
+
+/* We map both L3 and L4 on OMAP3 */
+#define L3_34XX_PHYS		L3_34XX_BASE	/* 0x68000000 */
+#define L3_34XX_VIRT		0xf8000000
+#define L3_34XX_SIZE		SZ_1M   /* 44kB of 128MB used, want 1MB sect */
+
+#define L4_34XX_PHYS		L4_34XX_BASE	/* 0x48000000 */
+#define L4_34XX_VIRT		0xd8000000
+#define L4_34XX_SIZE		SZ_4M   /* 1MB of 128MB used, want 1MB sect */
+
+/*
+ * Need to look at the Size 4M for L4.
+ * VPOM3430 was not working for Int controller
+ */
+
+#define L4_WK_34XX_PHYS		L4_WK_34XX_BASE /* 0x48300000 */
+#define L4_WK_34XX_VIRT		0xd8300000
+#define L4_WK_34XX_SIZE		SZ_1M
+
+#define L4_PER_34XX_PHYS	L4_PER_34XX_BASE /* 0x49000000 */
+#define L4_PER_34XX_VIRT	0xd9000000
+#define L4_PER_34XX_SIZE	SZ_1M
+
+#define L4_EMU_34XX_PHYS	L4_EMU_34XX_BASE /* 0x54000000 */
+#define L4_EMU_34XX_VIRT	0xe4000000
+#define L4_EMU_34XX_SIZE	SZ_64M
+
+#define OMAP34XX_GPMC_PHYS	OMAP34XX_GPMC_BASE /* 0x6E000000 */
+#define OMAP34XX_GPMC_VIRT	0xFE000000
+#define OMAP34XX_GPMC_SIZE	SZ_1M
+
+#define OMAP343X_SMS_PHYS	OMAP343X_SMS_BASE /* 0x6C000000 */
+#define OMAP343X_SMS_VIRT	0xFC000000
+#define OMAP343X_SMS_SIZE	SZ_1M
+
+#define OMAP343X_SDRC_PHYS	OMAP343X_SDRC_BASE /* 0x6D000000 */
+#define OMAP343X_SDRC_VIRT	0xFD000000
+#define OMAP343X_SDRC_SIZE	SZ_1M
+
+
+#define IO_OFFSET		0x90000000
+#define IO_ADDRESS(pa)		((pa) + IO_OFFSET)/* Works for L3 and L4 */
+#define io_p2v(pa)		((pa) + IO_OFFSET)/* Works for L3 and L4 */
+#define io_v2p(va)		((va) - IO_OFFSET)/* Works for L3 and L4 */
+
+/* DSP */
+#define DSP_MEM_34XX_PHYS	OMAP34XX_DSP_MEM_BASE	/* 0x58000000 */
+#define DSP_MEM_34XX_VIRT	0xe0000000
+#define DSP_MEM_34XX_SIZE	0x28000
+#define DSP_IPI_34XX_PHYS	OMAP34XX_DSP_IPI_BASE	/* 0x59000000 */
+#define DSP_IPI_34XX_VIRT	0xe1000000
+#define DSP_IPI_34XX_SIZE	SZ_4K
+#define DSP_MMU_34XX_PHYS	OMAP34XX_DSP_MMU_BASE	/* 0x5a000000 */
+#define DSP_MMU_34XX_VIRT	0xe2000000
+#define DSP_MMU_34XX_SIZE	SZ_4K
+
 #endif
 
 #ifndef __ASSEMBLER__

include/asm-arm/arch-omap/omap24xx.h

+/*
+ * include/asm-arm/arch-omap/omap24xx.h
+ *
+ * This file contains the processor specific definitions
+ * of the TI OMAP24XX.
+ *
+ * Copyright (C) 2007 Texas Instruments.
+ * Copyright (C) 2007 Nokia Corporation.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License as published by
+ * the Free Software Foundation; either version 2 of the License, or
+ * (at your option) any later version.
+ *
+ * This program is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ * GNU General Public License for more details.
+ *
+ * You should have received a copy of the GNU General Public License
+ * along with this program; if not, write to the Free Software
+ * Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA  02111-1307  USA
+ *
+ */
+
 #ifndef __ASM_ARCH_OMAP24XX_H
 #define __ASM_ARCH_OMAP24XX_H
 
@@ -13,33 +38,70 @@
 
 /* interrupt controller */
 #define OMAP24XX_IC_BASE	(L4_24XX_BASE + 0xfe000)
-#define VA_IC_BASE		IO_ADDRESS(OMAP24XX_IC_BASE)
 #define OMAP24XX_IVA_INTC_BASE	0x40000000
 #define IRQ_SIR_IRQ		0x0040
 
-#ifdef CONFIG_ARCH_OMAP2420
-#define OMAP24XX_32KSYNCT_BASE	(L4_24XX_BASE + 0x4000)
-#define OMAP24XX_PRCM_BASE	(L4_24XX_BASE + 0x8000)
-#define OMAP24XX_SDRC_BASE	(L3_24XX_BASE + 0x9000)
-#define OMAP242X_CONTROL_STATUS	(L4_24XX_BASE + 0x2f8)
-#endif
+#define OMAP2420_CTRL_BASE	L4_24XX_BASE
+#define OMAP2420_32KSYNCT_BASE	(L4_24XX_BASE + 0x4000)
+#define OMAP2420_PRCM_BASE	(L4_24XX_BASE + 0x8000)
+#define OMAP2420_CM_BASE	(L4_24XX_BASE + 0x8000)
+#define OMAP2420_PRM_BASE	OMAP2420_CM_BASE
+#define OMAP2420_SDRC_BASE	(L3_24XX_BASE + 0x9000)
+#define OMAP2420_SMS_BASE	0x68008000
 
-#ifdef CONFIG_ARCH_OMAP2430
-#define OMAP24XX_32KSYNCT_BASE	(L4_WK_243X_BASE + 0x20000)
-#define OMAP24XX_PRCM_BASE	(L4_WK_243X_BASE + 0x6000)
-#define OMAP24XX_SDRC_BASE	(0x6D000000)
-#define OMAP242X_CONTROL_STATUS	(L4_24XX_BASE + 0x2f8)
+#define OMAP2430_32KSYNCT_BASE	(L4_WK_243X_BASE + 0x20000)
+#define OMAP2430_PRCM_BASE	(L4_WK_243X_BASE + 0x6000)
+#define OMAP2430_CM_BASE	(L4_WK_243X_BASE + 0x6000)
+#define OMAP2430_PRM_BASE	OMAP2430_CM_BASE
+
+#define OMAP243X_SMS_BASE	0x6C000000
+#define OMAP243X_SDRC_BASE	0x6D000000
 #define OMAP243X_GPMC_BASE	0x6E000000
-#endif
+#define OMAP243X_SCM_BASE	(L4_WK_243X_BASE + 0x2000)
+#define OMAP243X_CTRL_BASE	OMAP243X_SCM_BASE
+#define OMAP243X_HS_BASE	(L4_24XX_BASE + 0x000ac000)
 
 /* DSP SS */
-#define OMAP24XX_DSP_BASE	0x58000000
-#define OMAP24XX_DSP_MEM_BASE	(OMAP24XX_DSP_BASE + 0x0)
-#define OMAP24XX_DSP_IPI_BASE	(OMAP24XX_DSP_BASE + 0x1000000)
-#define OMAP24XX_DSP_MMU_BASE	(OMAP24XX_DSP_BASE + 0x2000000)
+#define OMAP2420_DSP_BASE	0x58000000
+#define OMAP2420_DSP_MEM_BASE	(OMAP2420_DSP_BASE + 0x0)
+#define OMAP2420_DSP_IPI_BASE	(OMAP2420_DSP_BASE + 0x1000000)
+#define OMAP2420_DSP_MMU_BASE	(OMAP2420_DSP_BASE + 0x2000000)
+
+#define OMAP243X_DSP_BASE	0x5C000000
+#define OMAP243X_DSP_MEM_BASE	(OMAP243X_DSP_BASE + 0x0)
+#define OMAP243X_DSP_MMU_BASE	(OMAP243X_DSP_BASE + 0x1000000)
 
 /* Mailbox */
 #define OMAP24XX_MAILBOX_BASE	(L4_24XX_BASE + 0x94000)
 
+/* Camera */
+#define OMAP24XX_CAMERA_BASE	(L4_24XX_BASE + 0x52000)
+
+/* Security */
+#define OMAP24XX_SEC_BASE	(L4_24XX_BASE + 0xA0000)
+#define OMAP24XX_SEC_RNG_BASE	(OMAP24XX_SEC_BASE + 0x0000)
+#define OMAP24XX_SEC_DES_BASE	(OMAP24XX_SEC_BASE + 0x2000)
+#define OMAP24XX_SEC_SHA1MD5_BASE (OMAP24XX_SEC_BASE + 0x4000)
+#define OMAP24XX_SEC_AES_BASE	(OMAP24XX_SEC_BASE + 0x6000)
+#define OMAP24XX_SEC_PKA_BASE	(OMAP24XX_SEC_BASE + 0x8000)
+
+#if defined(CONFIG_ARCH_OMAP2420)
+
+#define OMAP2_32KSYNCT_BASE	OMAP2420_32KSYNCT_BASE
+#define OMAP2_PRCM_BASE		OMAP2420_PRCM_BASE
+#define OMAP2_CM_BASE		OMAP2420_CM_BASE
+#define OMAP2_PRM_BASE		OMAP2420_PRM_BASE
+#define OMAP2_VA_IC_BASE	IO_ADDRESS(OMAP24XX_IC_BASE)
+
+#elif defined(CONFIG_ARCH_OMAP2430)
+
+#define OMAP2_32KSYNCT_BASE	OMAP2430_32KSYNCT_BASE
+#define OMAP2_PRCM_BASE		OMAP2430_PRCM_BASE
+#define OMAP2_CM_BASE		OMAP2430_CM_BASE
+#define OMAP2_PRM_BASE		OMAP2430_PRM_BASE
+#define OMAP2_VA_IC_BASE	IO_ADDRESS(OMAP24XX_IC_BASE)
+
+#endif
+
 #endif /* __ASM_ARCH_OMAP24XX_H */