KVM: VMX: pass correct DR6 for GD userspace exit

When KVM_EXIT_DEBUG is raised for the disabled-breakpoints case (DR7.GD),
DR6 was incorrectly copied from the value in the VM.  Instead,
DR6.BD should be set in order to catch this case.

On AMD this does not need any special code because the processor triggers
a #DB exception that is intercepted.  However, the testcase would fail
without the previous patch because both DR6.BS and DR6.BD would be set.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>

arch/x86/kvm/vmx/vmx.c

@@ -4927,7 +4927,7 @@ static int handle_dr(struct kvm_vcpu *vcpu)
 		 * guest debugging itself.
 		 */
 		if (vcpu->guest_debug & KVM_GUESTDBG_USE_HW_BP) {
-			vcpu->run->debug.arch.dr6 = vcpu->arch.dr6;
+			vcpu->run->debug.arch.dr6 = DR6_BD | DR6_RTM | DR6_FIXED_1;
 			vcpu->run->debug.arch.dr7 = dr7;
 			vcpu->run->debug.arch.pc = kvm_get_linear_rip(vcpu);
 			vcpu->run->debug.arch.exception = DB_VECTOR;

tools/testing/selftests/kvm/x86_64/debug_regs.c

@@ -11,10 +11,13 @@
 
 #define VCPU_ID 0
 
+#define DR6_BD		(1 << 13)
+#define DR7_GD		(1 << 13)
+
 /* For testing data access debug BP */
 uint32_t guest_value;
 
-extern unsigned char sw_bp, hw_bp, write_data, ss_start;
+extern unsigned char sw_bp, hw_bp, write_data, ss_start, bd_start;
 
 static void guest_code(void)
 {
@@ -43,6 +46,8 @@ static void guest_code(void)
 		     "rdmsr\n\t"
 		     : : : "rax", "ecx");
 
+	/* DR6.BD test */
+	asm volatile("bd_start: mov %%dr0, %%rax" : : : "rax");
 	GUEST_DONE();
 }
 
@@ -165,6 +170,23 @@ int main(void)
 			    target_dr6);
 	}
 
+	/* Finally test global disable */
+	CLEAR_DEBUG();
+	debug.control = KVM_GUESTDBG_ENABLE | KVM_GUESTDBG_USE_HW_BP;
+	debug.arch.debugreg[7] = 0x400 | DR7_GD;
+	APPLY_DEBUG();
+	vcpu_run(vm, VCPU_ID);
+	target_dr6 = 0xffff0ff0 | DR6_BD;
+	TEST_ASSERT(run->exit_reason == KVM_EXIT_DEBUG &&
+		    run->debug.arch.exception == DB_VECTOR &&
+		    run->debug.arch.pc == CAST_TO_RIP(bd_start) &&
+		    run->debug.arch.dr6 == target_dr6,
+			    "DR7.GD: exit %d exception %d rip 0x%llx "
+			    "(should be 0x%llx) dr6 0x%llx (should be 0x%llx)",
+			    run->exit_reason, run->debug.arch.exception,
+			    run->debug.arch.pc, target_rip, run->debug.arch.dr6,
+			    target_dr6);
+
 	/* Disable all debug controls, run to the end */
 	CLEAR_DEBUG();
 	APPLY_DEBUG();