Commit 469dded1 authored by Anatolij Gustschin's avatar Anatolij Gustschin Committed by Linus Torvalds

misc/eeprom: add eeprom access driver for digsy_mtc board

Both displays on digsy_mtc board obtain their configuration from microwire
EEPROMs which are connected to the SoC over GPIO lines.  We need an easy
way to access the EEPROMs to write the needed display configuration or to
read out the currently programmed configuration.  The generic
eeprom_93xx46 SPI driver added by previous patch allows EEPROM access over
sysfs.  Using the simple driver added by this patch we provide used GPIO
interface and access control description on the board for generic
eeprom_93xx46 driver and spi_gpio driver.
Signed-off-by: default avatarAnatolij Gustschin <agust@denx.de>
Cc: Jonathan Cameron <jic23@cam.ac.uk>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: default avatarAndrew Morton <akpm@linux-foundation.org>
Signed-off-by: default avatarLinus Torvalds <torvalds@linux-foundation.org>
parent 06b4501e
...@@ -83,4 +83,16 @@ config EEPROM_93XX46 ...@@ -83,4 +83,16 @@ config EEPROM_93XX46
If unsure, say N. If unsure, say N.
config EEPROM_DIGSY_MTC_CFG
bool "DigsyMTC display configuration EEPROMs device"
depends on PPC_MPC5200_GPIO && GPIOLIB && SPI_GPIO
help
This option enables access to display configuration EEPROMs
on digsy_mtc board. You have to additionally select Microwire
EEPROM 93XX46 driver. sysfs entries will be created for that
EEPROM allowing to read/write the configuration data or to
erase the whole EEPROM.
If unsure, say N.
endmenu endmenu
...@@ -4,3 +4,4 @@ obj-$(CONFIG_EEPROM_LEGACY) += eeprom.o ...@@ -4,3 +4,4 @@ obj-$(CONFIG_EEPROM_LEGACY) += eeprom.o
obj-$(CONFIG_EEPROM_MAX6875) += max6875.o obj-$(CONFIG_EEPROM_MAX6875) += max6875.o
obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o obj-$(CONFIG_EEPROM_93CX6) += eeprom_93cx6.o
obj-$(CONFIG_EEPROM_93XX46) += eeprom_93xx46.o obj-$(CONFIG_EEPROM_93XX46) += eeprom_93xx46.o
obj-$(CONFIG_EEPROM_DIGSY_MTC_CFG) += digsy_mtc_eeprom.o
/*
* EEPROMs access control driver for display configuration EEPROMs
* on DigsyMTC board.
*
* (C) 2011 DENX Software Engineering, Anatolij Gustschin <agust@denx.de>
*
* This program is free software; you can redistribute it and/or modify
* it under the terms of the GNU General Public License version 2 as
* published by the Free Software Foundation.
*/
#include <linux/gpio.h>
#include <linux/init.h>
#include <linux/platform_device.h>
#include <linux/spi/spi.h>
#include <linux/spi/spi_gpio.h>
#include <linux/eeprom_93xx46.h>
#define GPIO_EEPROM_CLK 216
#define GPIO_EEPROM_CS 210
#define GPIO_EEPROM_DI 217
#define GPIO_EEPROM_DO 249
#define GPIO_EEPROM_OE 255
#define EE_SPI_BUS_NUM 1
static void digsy_mtc_op_prepare(void *p)
{
/* enable */
gpio_set_value(GPIO_EEPROM_OE, 0);
}
static void digsy_mtc_op_finish(void *p)
{
/* disable */
gpio_set_value(GPIO_EEPROM_OE, 1);
}
struct eeprom_93xx46_platform_data digsy_mtc_eeprom_data = {
.flags = EE_ADDR8,
.prepare = digsy_mtc_op_prepare,
.finish = digsy_mtc_op_finish,
};
static struct spi_gpio_platform_data eeprom_spi_gpio_data = {
.sck = GPIO_EEPROM_CLK,
.mosi = GPIO_EEPROM_DI,
.miso = GPIO_EEPROM_DO,
.num_chipselect = 1,
};
static struct platform_device digsy_mtc_eeprom = {
.name = "spi_gpio",
.id = EE_SPI_BUS_NUM,
.dev = {
.platform_data = &eeprom_spi_gpio_data,
},
};
static struct spi_board_info digsy_mtc_eeprom_info[] __initdata = {
{
.modalias = "93xx46",
.max_speed_hz = 1000000,
.bus_num = EE_SPI_BUS_NUM,
.chip_select = 0,
.mode = SPI_MODE_0,
.controller_data = (void *)GPIO_EEPROM_CS,
.platform_data = &digsy_mtc_eeprom_data,
},
};
static int __init digsy_mtc_eeprom_devices_init(void)
{
int ret;
ret = gpio_request_one(GPIO_EEPROM_OE, GPIOF_OUT_INIT_HIGH,
"93xx46 EEPROMs OE");
if (ret) {
pr_err("can't request gpio %d\n", GPIO_EEPROM_OE);
return ret;
}
spi_register_board_info(digsy_mtc_eeprom_info,
ARRAY_SIZE(digsy_mtc_eeprom_info));
return platform_device_register(&digsy_mtc_eeprom);
}
device_initcall(digsy_mtc_eeprom_devices_init);
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment