Merge tag 'spi-nor/for-5.3-v2' of...

Merge tag 'spi-nor/for-5.3-v2' of gitolite.kernel.org:pub/scm/linux/kernel/git/mtd/linux into mtd/next

SPI-NOR core changes:
- add support for the mt25ql02g and w25q16jv flashes
- print error in case of jedec read id fails
- is25lp256: add post BFPT fix to correct the addr_width

SPI NOR controller drivers changes:
- intel-spi: Add support for Intel Elkhart Lake SPI serial flash
- smt32: remove the driver as the driver was replaced by spi-stm32-qspi.c
- cadence-quadspi: add reset control

Documentation/devicetree/bindings/mtd/cadence-quadspi.txt

@@ -35,6 +35,9 @@ custom properties:
 		  (qspi_n_ss_out).
 - cdns,tslch-ns : Delay in nanoseconds between setting qspi_n_ss_out low
                   and first bit transfer.
+- resets	: Must contain an entry for each entry in reset-names.
+		  See ../reset/reset.txt for details.
+- reset-names	: Must include either "qspi" and/or "qspi-ocp".
 
 Example:
 
@@ -50,6 +53,8 @@ Example:
 		cdns,fifo-depth = <128>;
 		cdns,fifo-width = <4>;
 		cdns,trigger-address = <0x00000000>;
+		resets = <&rst QSPI_RESET>, <&rst QSPI_OCP_RESET>;
+		reset-names = "qspi", "qspi-ocp";
 
 		flash0: n25q00@0 {
 			...

Documentation/devicetree/bindings/mtd/stm32-quadspi.txt

-* STMicroelectronics Quad Serial Peripheral Interface(QuadSPI)
-
-Required properties:
-- compatible: should be "st,stm32f469-qspi"
-- reg: the first contains the register location and length.
-       the second contains the memory mapping address and length
-- reg-names: should contain the reg names "qspi" "qspi_mm"
-- interrupts: should contain the interrupt for the device
-- clocks: the phandle of the clock needed by the QSPI controller
-- A pinctrl must be defined to set pins in mode of operation for QSPI transfer
-
-Optional properties:
-- resets: must contain the phandle to the reset controller.
-
-A spi flash must be a child of the nor_flash node and could have some
-properties. Also see jedec,spi-nor.txt.
-
-Required properties:
-- reg: chip-Select number (QSPI controller may connect 2 nor flashes)
-- spi-max-frequency: max frequency of spi bus
-
-Optional property:
-- spi-rx-bus-width: see ../spi/spi-bus.txt for the description
-
-Example:
-
-qspi: spi@a0001000 {
-	compatible = "st,stm32f469-qspi";
-	reg = <0xa0001000 0x1000>, <0x90000000 0x10000000>;
-	reg-names = "qspi", "qspi_mm";
-	interrupts = <91>;
-	resets = <&rcc STM32F4_AHB3_RESET(QSPI)>;
-	clocks = <&rcc 0 STM32F4_AHB3_CLOCK(QSPI)>;
-	pinctrl-names = "default";
-	pinctrl-0 = <&pinctrl_qspi0>;
-
-	flash@0 {
-		reg = <0>;
-		spi-rx-bus-width = <4>;
-		spi-max-frequency = <108000000>;
-		...
-	};
-};

drivers/mtd/spi-nor/Kconfig

@@ -105,11 +105,4 @@ config SPI_INTEL_SPI_PLATFORM
 	  To compile this driver as a module, choose M here: the module
 	  will be called intel-spi-platform.
 
-config SPI_STM32_QUADSPI
-	tristate "STM32 Quad SPI controller"
-	depends on ARCH_STM32 || COMPILE_TEST
-	help
-	  This enables support for the STM32 Quad SPI controller.
-	  We only connect the NOR to this controller.
-
 endif # MTD_SPI_NOR

drivers/mtd/spi-nor/Makefile

@@ -8,4 +8,3 @@ obj-$(CONFIG_SPI_NXP_SPIFI)	+= nxp-spifi.o
 obj-$(CONFIG_SPI_INTEL_SPI)	+= intel-spi.o
 obj-$(CONFIG_SPI_INTEL_SPI_PCI)	+= intel-spi-pci.o
 obj-$(CONFIG_SPI_INTEL_SPI_PLATFORM)	+= intel-spi-platform.o
-obj-$(CONFIG_SPI_STM32_QUADSPI)	+= stm32-quadspi.o

drivers/mtd/spi-nor/cadence-quadspi.c

@@ -23,6 +23,7 @@
 #include <linux/of.h>
 #include <linux/platform_device.h>
 #include <linux/pm_runtime.h>
+#include <linux/reset.h>
 #include <linux/sched.h>
 #include <linux/spi/spi.h>
 #include <linux/timer.h>
@@ -1325,6 +1326,7 @@ static int cqspi_probe(struct platform_device *pdev)
 	struct cqspi_st *cqspi;
 	struct resource *res;
 	struct resource *res_ahb;
+	struct reset_control *rstc, *rstc_ocp;
 	const struct cqspi_driver_platdata *ddata;
 	int ret;
 	int irq;
@@ -1391,6 +1393,25 @@ static int cqspi_probe(struct platform_device *pdev)
 		goto probe_clk_failed;
 	}
 
+	/* Obtain QSPI reset control */
+	rstc = devm_reset_control_get_optional_exclusive(dev, "qspi");
+	if (IS_ERR(rstc)) {
+		dev_err(dev, "Cannot get QSPI reset.\n");
+		return PTR_ERR(rstc);
+	}
+
+	rstc_ocp = devm_reset_control_get_optional_exclusive(dev, "qspi-ocp");
+	if (IS_ERR(rstc_ocp)) {
+		dev_err(dev, "Cannot get QSPI OCP reset.\n");
+		return PTR_ERR(rstc_ocp);
+	}
+
+	reset_control_assert(rstc);
+	reset_control_deassert(rstc);
+
+	reset_control_assert(rstc_ocp);
+	reset_control_deassert(rstc_ocp);
+
 	cqspi->master_ref_clk_hz = clk_get_rate(cqspi->clk);
 	ddata  = of_device_get_match_data(dev);
 	if (ddata && (ddata->quirks & CQSPI_NEEDS_WR_DELAY))

drivers/mtd/spi-nor/intel-spi-pci.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * Intel PCH/PCU SPI flash PCI driver.
  *
  * Copyright (C) 2016, Intel Corporation
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <linux/ioport.h>
@@ -67,6 +64,7 @@ static const struct pci_device_id intel_spi_pci_ids[] = {
 	{ PCI_VDEVICE(INTEL, 0x18e0), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x19e0), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0x34a4), (unsigned long)&bxt_info },
+	{ PCI_VDEVICE(INTEL, 0x4b24), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0xa1a4), (unsigned long)&bxt_info },
 	{ PCI_VDEVICE(INTEL, 0xa224), (unsigned long)&bxt_info },
 	{ },

drivers/mtd/spi-nor/intel-spi-platform.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * Intel PCH/PCU SPI flash platform driver.
  *
  * Copyright (C) 2016, Intel Corporation
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <linux/ioport.h>

drivers/mtd/spi-nor/intel-spi.c

+// SPDX-License-Identifier: GPL-2.0
 /*
  * Intel PCH/PCU SPI flash driver.
  *
  * Copyright (C) 2016, Intel Corporation
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #include <linux/err.h>

drivers/mtd/spi-nor/intel-spi.h

+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * Intel PCH/PCU SPI flash driver.
  *
  * Copyright (C) 2016, Intel Corporation
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #ifndef INTEL_SPI_H

drivers/mtd/spi-nor/spi-nor.c

@@ -200,7 +200,7 @@ struct sfdp_header {
  *         register does not modify status register 2.
  * - 101b: QE is bit 1 of status register 2. Status register 1 is read using
  *         Read Status instruction 05h. Status register2 is read using
- *         instruction 35h. QE is set via Writ Status instruction 01h with
+ *         instruction 35h. QE is set via Write Status instruction 01h with
  *         two data bytes where bit 1 of the second byte is one.
  *         [...]
  */
@@ -1686,6 +1686,28 @@ static int sr2_bit7_quad_enable(struct spi_nor *nor)
 		.addr_width = 3,					\
 		.flags = SPI_NOR_NO_FR | SPI_S3AN,
 
+static int
+is25lp256_post_bfpt_fixups(struct spi_nor *nor,
+			   const struct sfdp_parameter_header *bfpt_header,
+			   const struct sfdp_bfpt *bfpt,
+			   struct spi_nor_flash_parameter *params)
+{
+	/*
+	 * IS25LP256 supports 4B opcodes, but the BFPT advertises a
+	 * BFPT_DWORD1_ADDRESS_BYTES_3_ONLY address width.
+	 * Overwrite the address width advertised by the BFPT.
+	 */
+	if ((bfpt->dwords[BFPT_DWORD(1)] & BFPT_DWORD1_ADDRESS_BYTES_MASK) ==
+		BFPT_DWORD1_ADDRESS_BYTES_3_ONLY)
+		nor->addr_width = 4;
+
+	return 0;
+}
+
+static struct spi_nor_fixups is25lp256_fixups = {
+	.post_bfpt = is25lp256_post_bfpt_fixups,
+};
+
 static int
 mx25l25635_post_bfpt_fixups(struct spi_nor *nor,
 			    const struct sfdp_parameter_header *bfpt_header,
@@ -1827,7 +1849,8 @@ static const struct flash_info spi_nor_ids[] = {
 			SECT_4K | SPI_NOR_DUAL_READ) },
 	{ "is25lp256",  INFO(0x9d6019, 0, 64 * 1024, 512,
 			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
-			SPI_NOR_4B_OPCODES) },
+			SPI_NOR_4B_OPCODES)
+			.fixups = &is25lp256_fixups },
 	{ "is25wp032",  INFO(0x9d7016, 0, 64 * 1024,  64,
 			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ) },
 	{ "is25wp064",  INFO(0x9d7017, 0, 64 * 1024, 128,
@@ -1880,6 +1903,9 @@ static const struct flash_info spi_nor_ids[] = {
 	{ "n25q512ax3",  INFO(0x20ba20, 0, 64 * 1024, 1024, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ) },
 	{ "n25q00",      INFO(0x20ba21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
 	{ "n25q00a",     INFO(0x20bb21, 0, 64 * 1024, 2048, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
+	{ "mt25ql02g",   INFO(0x20ba22, 0, 64 * 1024, 4096,
+			      SECT_4K | USE_FSR | SPI_NOR_QUAD_READ |
+			      NO_CHIP_ERASE) },
 	{ "mt25qu02g",   INFO(0x20bb22, 0, 64 * 1024, 4096, SECT_4K | USE_FSR | SPI_NOR_QUAD_READ | NO_CHIP_ERASE) },
 
 	/* Micron */
@@ -1996,6 +2022,11 @@ static const struct flash_info spi_nor_ids[] = {
 			SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
 	},
 	{ "w25x32", INFO(0xef3016, 0, 64 * 1024,  64, SECT_4K) },
+	{
+		"w25q16jv-im/jm", INFO(0xef7015, 0, 64 * 1024,  32,
+			SECT_4K | SPI_NOR_DUAL_READ | SPI_NOR_QUAD_READ |
+			SPI_NOR_HAS_LOCK | SPI_NOR_HAS_TB)
+	},
 	{ "w25q20cl", INFO(0xef4012, 0, 64 * 1024,  4, SECT_4K) },
 	{ "w25q20bw", INFO(0xef5012, 0, 64 * 1024,  4, SECT_4K) },
 	{ "w25q20ew", INFO(0xef6012, 0, 64 * 1024,  4, SECT_4K) },
@@ -2062,7 +2093,7 @@ static const struct flash_info *spi_nor_read_id(struct spi_nor *nor)
 
 	tmp = nor->read_reg(nor, SPINOR_OP_RDID, id, SPI_NOR_MAX_ID_LEN);
 	if (tmp < 0) {
-		dev_dbg(nor->dev, "error %d reading JEDEC ID\n", tmp);
+		dev_err(nor->dev, "error %d reading JEDEC ID\n", tmp);
 		return ERR_PTR(tmp);
 	}
 

include/linux/platform_data/intel-spi.h

+/* SPDX-License-Identifier: GPL-2.0 */
 /*
  * Intel PCH/PCU SPI flash driver.
  *
  * Copyright (C) 2016, Intel Corporation
  * Author: Mika Westerberg <mika.westerberg@linux.intel.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of the GNU General Public License version 2 as
- * published by the Free Software Foundation.
  */
 
 #ifndef INTEL_SPI_PDATA_H