Merge mandrakesoft.com:/home/jgarzik/vanilla/linus-2.5

into mandrakesoft.com:/home/jgarzik/repo/net-drivers-2.5

Documentation/networking/e100.txt

+Linux* Base Driver for the Intel(R) PRO/100 Family of Adapters
+==============================================================
+
+April 9, 2002
+
+
+Contents
+========
+
+- In This Release
+- Supported Adapters
+- Command Line Parameters
+- CPU Cycle Saver
+- Additional Configurations
+- Support
+
+
+In This Release
+===============
+
+This file describes the Linux* Base Driver for the Intel(R) PRO/100 Family of
+Adapters, version 2.0.x.  This driver includes support for Itanium(TM)-based 
+systems.
+
+New for this release:
+
+   - Additional ethtool functionality, including link status test and EEPROM 
+     read/write. A third-party application can use the ethtool interface to 
+     get and set driver parameters.
+
+   - Support for Zero copy on 82550-based adapters. This feature provides 
+     faster data throughput and significant CPU usage improvement in systems 
+     that use the relevant system call (sendfile(2)).
+
+   - Support for large MTU-enabling interface (1504 bytes) with kernel's 
+     VLAN module
+
+   - Support for polling on RX
+
+   - Support for Wake On LAN* on 82550 and 82559-based adapters
+
+
+Supported Adapters
+==================
+
+The following Intel network adapters are compatible with the drivers 
+in this release:
+
+Controller  Adapter Name                            Board IDs
+----------  ------------                            ---------
+
+82558       PRO/100+ PCI Adapter                    668081-xxx, 689661-xxx
+
+82558       PRO/100+ Management Adapter             691334-xxx, 701738-xxx,
+                                                    721383-xxx
+
+82558       PRO/100+ Dual Port Server Adapter       714303-xxx, 711269-xxx, 
+                                                    A28276-xxx
+
+82558       PRO/100+ PCI Server Adapter             710550-xxx
+
+82550       PRO/100 S Server Adapter                752438-xxx (82550)
+82559                                               A56831-xxx, A10563-xxx,
+                                                    A12171-xxx, A12321-xxx, 
+                                                    A12320-xxx, A12170-xxx
+                                                    748568-xxx (82559)
+                                                    748565-xxx (82559)
+
+
+82550       PRO/100 S Desktop Adapter               751767-xxx (82550)
+82559                                               748592-xxx, A12167-xxx, 
+                                                    A12318-xxx, A12317-xxx, 
+                                                    A12165-xxx
+                                                    748569-xxx (82559)
+
+
+
+82559       PRO/100+ Server Adapter                 729757-xxx
+
+82559       PRO/100 S Management Adapter            748566-xxx, 748564-xxx
+
+82550       PRO/100 S Dual Port Server Adapter      A56831-xxx
+
+82551       PRO/100 M Desktop Adapter               A80897-xxx
+
+            PRO/100 S Advanced Management Adapter   747842-xxx, 745171-xxx
+
+CNR         PRO/100 VE Desktop Adapter              A10386-xxx, A10725-xxx, 
+                                                    A23801-xxx, A19716-xxx
+
+
+            PRO/100 VM Desktop Adapter              A14323-xxx, A19725-xxx, 
+                                                    A23801-xxx, A22220-xxx, 
+                                                    A23796-xxx
+   
+
+To verify that your adapter is supported, find the board ID number on the 
+adapter. Look for a label that has a barcode and a number in the format 
+123456-001 (six digits hyphen three digits). Match this to the list of 
+numbers above.
+
+For more information on how to identify your adapter, go to the Adapter & 
+Driver ID Guide at:
+
+  http://support.intel.com/support/network/adapter/pro100/21397.htm
+
+For the latest Intel PRO/100 network driver for Linux, see:
+
+  http://appsr.intel.com/scripts-df/support_intel.asp
+
+
+Command Line Parameters
+=======================
+
+The following parameters are used by entering them on the command line with 
+the modprobe or insmod command. For example, with two Intel PRO/100 PCI 
+adapters, entering:
+	
+     modprobe e100 TxDescriptors=32,128
+
+loads the e100 driver with 32 TX resources for the first adapter and 128 TX 
+resources for the second adapter. This configuration favors the second 
+adapter. The driver supports up to 16 network adapters concurrently.
+
+NOTE: Giving any command line option the value "-1" causes the driver to use 
+      the appropriate default value for that option, as if no value was 
+      specified.
+
+
+BundleMax
+Valid Range: 0x1-0xFFFF
+Default Value: 6
+   This parameter holds the maximum number of packets in a bundle. Suggested 
+   values range from 2 to 10. See "CPU Cycle Saver."
+
+BundleSmallFr
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 0
+   The value 1 (on) causes small packets (less than 128 bytes) to be bundled. 
+   See "CPU Cycle Saver."
+
+e100_speed_duplex
+Valid Range: 0-4 (1=10half;2=10full;3=100half;4=100full)
+Default Value: 0
+   The default value of 0 is set to auto-negotiate if the link partner is set
+   to auto-negotiate. If the link partner is forced, e100_speed_duplex 
+   defaults to half-duplex. 
+   Example usage: insmod e100.o e100_speed_duplex=4,4 (for two adapters)
+
+flow_control
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 0
+   This parameter controls the automatic generation(Tx) and response(Rx) to 
+   Ethernet PAUSE frames. flow_control should NOT be set to 1 when the e100 
+   adapter is connected to an interface that does not support Ethernet PAUSE 
+   frames and when the e100_speed_duplex parameter is NOT set to zero. 
+
+IntDelay
+Valid Range: 0-0xFFFF (0=off)
+Default Value: 1536
+   This parameter holds the number of time units (in adapter terminology)
+   until the adapter generates an interrupt. The recommended value for 
+   IntDelay is 0x600 (upon initialization). Suggested values range from 
+   0x200h to 0x800. See "CPU Cycle Saver."
+
+IFS
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 1
+  Inter Frame Spacing (IFS) aims to reduce the number of Ethernet frame
+  collisions by altering the time between frame transmissions. When IFS is 
+  enabled the driver tries to find an optimal IFS value. However, some 
+  switches function better when IFS is disabled.
+
+PollingMaxWork
+Valid Range: 1-1024 (max number of RxDescriptors)
+Default Value: Specified number of RxDescriptors
+  This value specifies the maximum number of receive packets that are 
+  processed on a single polling call. This parameter is invalid if 
+  RxCongestionControl is set to 0.
+
+RxCongestionControl
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 1
+  1 enables polling mode. When the link is congested, the driver can decide 
+  to handle received packets by polling them, instead of waiting until 
+  interrupts occur.
+
+RxDescriptors
+Valid Range: 8-1024
+Default Value: 64
+   This parameter defines the number of receive descriptors allocated by 
+   the driver. Increasing this value allows the driver to buffer more 
+   incoming packets before the driver is required to service an interrupt. 
+   The maximum value for Itanium-based systems is 64.
+
+TxDescriptors
+Valid Range: 19-1024
+Default Value: 64
+   This value is the number of transmit descriptors allocated by the driver. 
+   Increasing this value allows the protocol stack to queue more transmits at
+   the driver level. The maximum value for Itanium-based systems is 64.
+
+ucode (not available for 82557-based adapters)
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 0 for 82558-based adapters
+               1 for 82559(and higher)-based adapters
+   On uploads the micro code to the adapter, which enables CPU Cycle Saver. 
+   See the section "CPU Cycle Saver" below.
+   Example usage: insmod e100.o ucode=0  (does not reduce CPU usage)
+
+XsumRX
+Valid Range: 0-1 (0=off, 1=on)
+Default Value: 1
+   On allows Rx checksum offloading for TCP/UDP packets. Requires that the 
+   hardware support this feature.
+
+
+CPU Cycle Saver
+================
+
+CPU Cycle Saver reduces CPU utilization by reducing the number of interrupts 
+that the adapter generates.
+
+When CPU Cycle Saver is turned off, the adapter generates one interrupt for 
+every frame that is received. This means that the operating system stops what
+it is doing and switches to the network driver in order to process the 
+receive.
+
+When CPU Cycle Saver is on, the adapter does not generate an interrupt for 
+every frame it receives. Instead, it waits until it receives several frames 
+before generating an interrupt. This reduces the amount of time spent 
+switching to and from the driver. 
+
+CPU Cycle Saver consists of these arguments: IntDelay, BundleMax and 
+BundleSmallFr. When IntDelay is increased, the adapter waits longer for 
+frames to arrive before generating the interrupt. By increasing BundleMax, 
+the network adapter waits for the number of frames specified to arrive before 
+generating the interrupt. When BundleSmallFr is disabled, the adapter does 
+not bundle packets that are smaller than 128 bytes. Such small packets are 
+often, but not always, control packets that are better served immediately.
+
+For most users, it is recommended that CPU Cycle Saver be used with the 
+default values specified in the Command Line Parameters section. However, in 
+some cases, performance problems may occur with CPU Cycle Saver. If such 
+problems are observed, we recommend turning off this feature by setting 
+ucode=0.
+
+
+Support
+=======
+
+For general information and support, go to the Intel support website at:
+
+    http://support.intel.com
+
+If an issue is identified with the released source code on the supported
+kernel with a supported adapter, email the specific information related to 
+the issue to linux.nics@intel.com.
+
+
+License
+=======
+
+This software program is released under the terms of a license agreement 
+between you ('Licensee') and Intel. Do not use or load this software or any 
+associated materials (collectively, the 'Software') until you have carefully 
+read the full terms and conditions of the LICENSE located in this software 
+package. By loading or using the Software, you agree to the terms of this 
+Agreement. If you do not agree with the terms of this Agreement, do not 
+install or use the Software.
+
+* Other names and brands may be claimed as the property of others.

Documentation/networking/e1000.txt

 Linux* Base Driver for the Intel(R) PRO/1000 Family of Adapters
 ===============================================================
 
-February 5, 2002
+April 23, 2002
 
 
 Contents
@@ -11,6 +11,7 @@ Contents
 - Supported Adapters
 - Command Line Parameters
 - Speed and Duplex Configuration
+- Additional Configurations
 - Known Issues
 - Support
 
@@ -19,17 +20,27 @@ In This Release
 ===============
 
 This file describes the Linux* Base Driver for the Intel(R) PRO/1000 Family
-of Adapters, version 4.2.x.
-This driver includes support for Itanium(TM)-based systems.
+of Adapters, version 4.2.x.  This driver includes support for 
+Itanium(TM)-based systems.
 
 This release version includes the following:
 
-   - support for the ethtool 1.4 interface. A third-party application can use
+   - Support for the ethtool 1.5 interface. A third-party application can use
      the ethtool interface to get and set driver parameters.
 
-   - the zero copy feature. Zero copy provides faster information throughput.
-     By default, this feature is enabled if using a kernel that supports it.
-     Zero copy is not supported on the original PWLA8490 (plain) adapter.
+   - Zero copy. This feature provides faster data throughput. Enabled by
+     default in supporting kernels. It is not supported on the Intel(R)
+     PRO/1000 Gigabit Server Adapter.
+
+New features include:
+
+   - Support for the 82545 and 82546-based adapters listed below
+
+   - Wake on LAN* support via ethtool for 82540, 82544, 82545, and 82546-
+     based adapters
+
+   - Adaptive IFS for increased performance at half duplex
+
 
 
 Supported Adapters
@@ -38,21 +49,32 @@ Supported Adapters
 The following Intel network adapters are compatible with the drivers in this
 release:
 
-   Controller  Adapter Name                     Board IDs
-   ----------  ------------                     ---------
+   Controller  Adapter Name                         Board IDs
+   ----------  ------------                         ---------
+
+   82542       PRO/1000 Gigabit Server Adapter      700262-xxx, 717037-xxx
+
+   82543       PRO/1000 F Server Adapter            738640-xxx, A38888-xxx
+
+   82543       PRO/1000 T Server Adapter            A19845-xxx, A33948-xxx
+
+   82544       PRO/1000 XT Server Adapter           A51580-xxx
+
+   82544       PRO/1000 XF Server Adapter           A50484-xxx
 
-   82542       PRO/1000 Gigabit Server Adapter  700262-xxx, 717037-xxx
+   82544       PRO/1000 T Desktop Adapter           A62947-xxx
 
-   82543       PRO/1000 F Server Adapter        738640-xxx, A38888-xxx,
-                                                A06512-xxx
+   82540       PRO/1000 MT Desktop Adapter          A78408-xxx
 
-   82543       PRO/1000 T Server Adapter        A19845-xxx, A33948-xxx
+   82545       PRO/1000 MT Server Adapter           A92165-xxx
 
-   82544       PRO/1000 XT Server Adapter       A51580-xxx
+   82546       PRO/1000 MT Dual Port Server Adapter A92111-xxx
 
-   82544       PRO/1000 XF Server Adapter       A50484-xxx
+   82545       PRO/1000 MF Server Adapter           A91622-xxx
 
-   82544       PRO/1000 T Desktop Adapter       A62947-xxx
+   82545       PRO/1000 MF Server Adapter(LX)       A91624-xxx
+
+   82546       PRO/1000 MF Dual Port Server Adapter A91620-xxx
 
 
 To verify your Intel adapter is supported, find the board ID number on the
@@ -73,8 +95,8 @@ For the latest Intel network drivers for Linux, go to:
 Command Line Parameters
 =======================
 
-If the driver is built as a module, the following parameters are used by
-entering them on the command line with the modprobe or insmod command.
+If the driver is built as a module, the following parameters are used by 
+entering them on the command line with the modprobe or insmod command. 
 For example, with two PRO/1000 PCI adapters, entering:
 
     insmod e1000 TxDescriptors=80,128
@@ -86,14 +108,14 @@ For more information about the AutoNeg, Duplex, and Speed parameters, see the
 "Speed and Duplex Configuration" section in this document.
 
 
-AutoNeg (Intel PRO/1000 T and PRO/1000 XT server adapters only)
-Valid Range: 0-0x0F, 0x20-0x2F
+AutoNeg (adapters using copper connections only)
+Valid Range: 0x01-0x0F, 0x20-0x2F
 Default Value: 0x2F
     This parameter is a bit mask that specifies which speed and duplex
     settings the board advertises. When this parameter is used, the Speed and
     Duplex parameters must not be specified.
 
-Duplex (Intel PRO/1000 T and PRO/1000 XT server adapters only)
+Duplex (adapters using copper connections only)
 Valid Range: 0-2 (0=auto-negotiate, 1=half, 2=full)
 Default Value: 0
     Defines the direction in which data is allowed to flow. Can by either one
@@ -109,26 +131,27 @@ Default: Read flow control settings from the EEPROM
 
 RxDescriptors
 Valid Range: 80-256 for 82542 and 82543-based adapters
-             80-4096 for 82544-based adapters
-Default Value: 256
+             80-4096 for 82540, 82544, 82545, and 82546-based adapters
+Default Value: 80
     This value is the number of receive descriptors allocated by the driver.
     Increasing this value allows the driver to buffer more incoming packets.
     Each descriptor is 16 bytes.  A receive buffer is also allocated for each
     descriptor and can be either 2048, 4096, 8192, or 16384 bytes, depending
-    on the MTU setting.
+    on the MTU setting. The maximum MTU size is 16110.
 
 RxIntDelay
 Valid Range: 0-65535 (0=off)
-Default Value: 64
+Default Value: 64 (82542, 82543, and 82544-based adapters)
+               128 (82540, 82545, and 82546-based adapters)
     This value delays the generation of receive interrupts in units of 1.024
     microseconds.  Receive interrupt reduction can improve CPU efficiency if
     properly tuned for specific network traffic. Increasing this value adds
     extra latency to frame reception and can end up decreasing the throughput
-    of TCP traffic.  If the system is reporting dropped receives, this value
+    of TCP traffic. If the system is reporting dropped receives, this value
     may be set too high, causing the driver to run out of available receive
     descriptors.
 
-Speed (Intel PRO/1000 T and PRO/1000 XT server adapters only)
+Speed (adapters using copper connections only)
 Valid Settings: 0, 10, 100, 1000
 Default Value: 0 (auto-negotiate at all supported speeds)
     Speed forces the line speed to the specified value in megabits per second
@@ -138,21 +161,12 @@ Default Value: 0 (auto-negotiate at all supported speeds)
 
 TxDescriptors
 Valid Range: 80-256 for 82542 and 82543-based adapters
-             80-4096 for 82544-based adapters
+             80-4096 for 82540, 82544, 82545, and 82546-based adapters
 Default Value: 256
     This value is the number of transmit descriptors allocated by the driver.
     Increasing this value allows the driver to queue more transmits. Each
     descriptor is 16 bytes.
 
-TxIntDelay
-Valid Range: 0-65535 (0=off)
-Default Value: 64
-    This value delays the generation of transmit interrupts in units of 1.024
-    microseconds.  Transmit interrupt reduction can improve CPU efficiency if
-    properly tuned for specific network traffic.  If the system is reporting
-    dropped transmits, this value may be set too high causing the driver to
-    run out of available transmit descriptors.
-
 XsumRX (not available on the PRO/1000 Gigabit Server Adapter)
 Valid Range: 0-1
 Default Value: 1
@@ -163,9 +177,8 @@ Default Value: 1
 Speed and Duplex Configuration
 ==============================
 
-Three keywords are used to control the speed and duplex configuration of the
-PRO/1000 T and PRO/1000 XT server adapters. These keywords are Speed, Duplex,
-and AutoNeg.
+Three keywords are used to control the speed and duplex configuration. These
+keywords are Speed, Duplex, and AutoNeg.
 
 If the board uses a fiber interface, these keywords are ignored, and the
 fiber interface board only links at 1000 Mbps full-duplex.
@@ -199,16 +212,32 @@ set to auto-negotiate. If the link partner is forced speed/duplex, the
 adapter MUST be forced to the same speed/duplex.
 
 
+Additional Configurations
+=========================
+
+  Jumbo Frames
+  ------------
+
+  The driver supports Jumbo Frames for all adapters except 82542-based
+  adapters.  Jumbo Frames support is enabled by changing the MTU to a value
+  larger than the default of 1500.  Use the ifconfig command to increase the
+  MTU size. For example:
+
+        ifconfig ethx mtu 9000 up
+
+
 Known Issues
 ============
 
-  Driver Hangs Under Heavy Traffic Loads
-  --------------------------------------
+  Inconsistent Driver Behavior Under Heavy Traffic Loads
+  ------------------------------------------------------
 
-  Intel is aware that previously released e1000 drivers may hang under very
-  specific types of heavy traffic loads. This version includes a workaround
-  that resets the adapter automatically if a hang condition is detected. This
-  workaround ensures network traffic flow is not affected when a hang occurs.
+  Adapters based on the Intel 82543 and 82544 LAN controllers may hang (stop
+  transmitting) under certain network conditions. If this occurs a message
+  is logged in the system event log. In addition, the controller is
+  automatically reset, restoring the network connection. To eliminate the
+  potential for the hang change the RxIntDelay parameter to zero. For details
+  on the RxIntDelay parameter see the Command Line Parameters section.
 
   Jumbo Frames System Requirement
   -------------------------------

MAINTAINERS

@@ -795,6 +795,11 @@ P:	Tigran Aivazian
 M:	tigran@veritas.com
 S:	Maintained
 
+INTEL PRO/100 ETHERNET SUPPORT
+P:	Scott Feldman
+M:	scott.feldman@intel.com
+S:	Supported
+
 INTEL PRO/1000 GIGABIT ETHERNET SUPPORT
 P:	Chris Leech
 M:	christopher.leech@intel.com

drivers/net/Config.help

@@ -828,18 +828,23 @@ CONFIG_E1000
   This driver supports Intel(R) PRO/1000 gigabit ethernet family of
   adapters, which includes:
 
-     Controller  Adapter Name                     Board IDs
-     ----------  ------------                     ---------
-     82542       PRO/1000 Gigabit Server Adapter  700262-xxx,
-                                                  717037-xxx
-     82543       PRO/1000 F Server Adapter        738640-xxx,
-                                                  A38888-xxx,
-                                                  A06512-xxx
-     82543       PRO/1000 T Server Adapter        A19845-xxx,
-                                                  A33948-xxx
-     82544       PRO/1000 XT Server Adapter       A51580-xxx
-     82544       PRO/1000 XF Server Adapter       A50484-xxx
-     82544       PRO/1000 T Desktop Adapter       A62947-xxx
+     Controller  Adapter Name                         Board IDs
+     ----------  ------------                         ---------
+     82542       PRO/1000 Gigabit Server Adapter      700262-xxx,
+                                                      717037-xxx
+     82543       PRO/1000 F Server Adapter            738640-xxx,
+                                                      A38888-xxx
+     82543       PRO/1000 T Server Adapter            A19845-xxx,
+                                                      A33948-xxx
+     82544       PRO/1000 XT Server Adapter           A51580-xxx
+     82544       PRO/1000 XF Server Adapter           A50484-xxx
+     82544       PRO/1000 T Desktop Adapter           A62947-xxx
+     82540       PRO/1000 MT Desktop Adapter          A78408-xxx
+     82545       PRO/1000 MT Server Adapter           A92165-xxx
+     82546       PRO/1000 MT Dual Port Server Adapter A92111-xxx
+     82545       PRO/1000 MF Server Adapter           A91622-xxx
+     82545       PRO/1000 MF Server Adapter(LX)       A91624-xxx
+     82546       PRO/1000 MF Dual Port Server Adapter A91620-xxx 
 
   For more information on how to identify your adapter, go to the
   Adapter & Driver ID Guide at:
@@ -1358,6 +1363,80 @@ CONFIG_EEPRO100
   a module, say M here and read <file:Documentation/modules.txt> as
   well as <file:Documentation/networking/net-modules.txt>.
 
+CONFIG_E100
+  This driver supports Intel(R) PRO/100 family of adapters, which 
+  includes:
+
+     Controller  Adapter Name                       Board IDs
+     ----------  ------------                       ---------
+
+     82558       PRO/100+ PCI Adapter               668081-xxx, 
+                                                    689661-xxx
+     82558       PRO/100+ Management Adapter        691334-xxx, 
+                                                    701738-xxx,
+                                                    721383-xxx
+     82558       PRO/100+ Dual Port Server Adapter  714303-xxx, 
+                                                    711269-xxx, 
+                                                    A28276-xxx
+     82558       PRO/100+ PCI Server Adapter        710550-xxx
+     82550       PRO/100 S Server Adapter           752438-xxx
+     82559                                          A56831-xxx, 
+                                                    A10563-xxx,
+                                                    A12171-xxx, 
+                                                    A12321-xxx, 
+                                                    A12320-xxx, 
+                                                    A12170-xxx
+                                                    748568-xxx
+                                                    748565-xxx
+     82550       PRO/100 S Desktop Adapter          751767-xxx
+     82559                                          748592-xxx, 
+                                                    A12167-xxx, 
+                                                    A12318-xxx, 
+                                                    A12317-xxx, 
+                                                    A12165-xxx,
+                                                    748569-xxx 
+     82559       PRO/100+ Server Adapter            729757-xxx
+     82559       PRO/100 S Management Adapter       748566-xxx, 
+                                                    748564-xxx
+     82550       PRO/100 S Dual Port Server Adapter A56831-xxx
+     82551       PRO/100 M Desktop Adapter          A80897-xxx
+                 PRO/100 S Advanced Management Adapter 
+                                                    747842-xxx, 
+                                                    745171-xxx
+     CNR         PRO/100 VE Desktop Adapter         A10386-xxx, 
+                                                    A10725-xxx, 
+                                                    A23801-xxx, 
+                                                    A19716-xxx
+                 PRO/100 VM Desktop Adapter         A14323-xxx, 
+                                                    A19725-xxx, 
+                                                    A23801-xxx, 
+                                                    A22220-xxx, 
+                                                    A23796-xxx
+   
+
+  To verify that your adapter is supported, find the board ID number 
+  on the adapter. Look for a label that has a barcode and a number 
+  in the format 123456-001 (six digits hyphen three digits). Match 
+  this to the list of numbers above.
+
+  For more information on how to identify your adapter, go to the 
+  Adapter & Driver ID Guide at:
+
+    http://support.intel.com/support/network/adapter/pro100/21397.htm
+
+  For the latest Intel PRO/100 network driver for Linux, see:
+
+    http://appsr.intel.com/scripts-df/support_intel.asp
+
+  More specific information on configuring the driver is in 
+  <file:Documentation/networking/e100.txt>.
+
+  This driver is also available as a module ( = code which can be
+  inserted in and removed from the running kernel whenever you want).
+  The module will be called e100.o.  If you want to compile it as a
+  module, say M here and read <file:Documentation/modules.txt> as well
+  as <file:Documentation/networking/net-modules.txt>.
+
 CONFIG_FEALNX
   Say Y here to support the Mysom MTD-800 family of PCI-based Ethernet
   cards. Specifications and data at

drivers/net/e100/e100.h

@@ -503,6 +503,7 @@ enum led_state_e {
 #define IS_BACHELOR        0x00000010	/* set if 82558 or newer board */
 #define IS_ICH             0x00000020
 #define DF_SPEED_FORCED    0x00000040	/* set if speed is forced */
+#define LED_IS_ON	   0x00000080	/* LED is turned ON by the driver */
 
 typedef struct net_device_stats net_dev_stats_t;
 
@@ -909,7 +910,6 @@ struct ethtool_lpbk_data{
 };
 #endif
 
-
 struct e100_private {
 	u32 flags;		/* board management flags */
 	u32 tx_per_underrun;	/* number of good tx frames per underrun */
@@ -998,8 +998,11 @@ struct e100_private {
 	u32 wolopts;
 	u16 ip_lbytes;
 #endif
-#ifdef ETHTOOL_TEST
-struct ethtool_lpbk_data loopback;
+#ifdef ETHTOOL_TEST 
+	struct ethtool_lpbk_data loopback;
+#endif
+#ifdef ETHTOOL_PHYS_ID
+	struct timer_list blink_timer;	/* led blink timer id */
 #endif
 
 #ifdef CONFIG_PM

drivers/net/e100/e100_config.c

@@ -593,7 +593,6 @@ e100_config_wol(struct e100_private *bdp)
 }
 #endif
 
-#ifdef ETHTOOL_TEST
 /**
  * e100_config_loopback_mode
  * @bdp: atapter's private data struct
@@ -690,5 +689,4 @@ e100_config_dynamic_tbd(struct e100_private *bdp, unsigned char enable)
  
         return bc_changed;
 }
-#endif
 

drivers/net/e100/e100_main.c

@@ -163,6 +163,9 @@ static char *test_strings[] = {
 	"E100_LPBK_PHY_FAIL"
 };
 
+#endif
+#ifdef	ETHTOOL_PHYS_ID
+static int e100_ethtool_led_blink(struct net_device *, struct ifreq *);
 #endif
 #endif /*E100_ETHTOOL_IOCTL */
 
@@ -182,7 +185,7 @@ static void e100_non_tx_background(unsigned long);
 /* Global Data structures and variables */
 char e100_copyright[] __devinitdata = "Copyright (c) 2002 Intel Corporation";
 
-#define E100_VERSION  "2.0.27-pre3"
+#define E100_VERSION  "2.0.30-k1"
 
 #define E100_FULL_DRIVER_NAME 	"Intel(R) PRO/100 Fast Ethernet Adapter - Loadable driver, ver "
 
@@ -691,9 +694,10 @@ e100_found1(struct pci_dev *pcid, const struct pci_device_id *ent)
 #ifdef ETHTOOL_GWOL
 	/* Disabling all WOLs as initialization */
 	bdp->wolsupported = bdp->wolopts = 0;
-	if (bdp->rev_id >= D101MA_REV_ID) {
-		bdp->wolsupported =
-			WAKE_PHY | WAKE_UCAST | WAKE_ARP | WAKE_MAGIC;
+	if (bdp->rev_id >= D101A4_REV_ID) {
+		bdp->wolsupported = WAKE_PHY | WAKE_MAGIC;
+		if (bdp->rev_id >= D101MA_REV_ID)
+			bdp->wolsupported |= WAKE_UCAST | WAKE_ARP;
 		bdp->wolopts = WAKE_MAGIC;
 	}
 #endif
@@ -3334,6 +3338,11 @@ e100_do_ethtool_ioctl(struct net_device *dev, struct ifreq *ifr)
 	case ETHTOOL_GSTRINGS:
 		rc = e100_ethtool_gstrings(dev,ifr);
 		break;
+#endif
+#ifdef	ETHTOOL_PHYS_ID
+	case ETHTOOL_PHYS_ID:
+		rc = e100_ethtool_led_blink(dev,ifr);
+		break;
 #endif
 	default:
 		break;
@@ -3641,6 +3650,94 @@ e100_ethtool_eeprom(struct net_device *dev, struct ifreq *ifr)
 }
 #endif
 
+#ifdef ETHTOOL_PHYS_ID
+#define E100_BLINK_INTERVAL	(HZ/4)
+/**
+ * e100_led_control
+ * @bdp: atapter's private data struct
+ * @led_mdi_op: led operation
+ *
+ * Software control over adapter's led. The possible operations are:
+ * TURN LED OFF, TURN LED ON and RETURN LED CONTROL TO HARDWARE.
+ */
+static void
+e100_led_control(struct e100_private *bdp, u16 led_mdi_op)
+{
+	spin_lock_bh(&bdp->mdi_access_lock);
+
+	e100_mdi_write(bdp, PHY_82555_LED_SWITCH_CONTROL,
+		       bdp->phy_addr, led_mdi_op);
+
+	spin_unlock_bh(&bdp->mdi_access_lock);
+}
+/**
+ * e100_led_blink_callback
+ * @data: pointer to atapter's private data struct
+ *
+ * Blink timer callback function. Toggles ON/OFF led status bit and calls
+ * led hardware access function. 
+ */
+static void
+e100_led_blink_callback(unsigned long data)
+{
+	struct e100_private *bdp = (struct e100_private *) data;
+
+	if(bdp->flags & LED_IS_ON) {
+		bdp->flags &= ~LED_IS_ON;
+		e100_led_control(bdp, PHY_82555_LED_OFF);
+	} else {
+		bdp->flags |= LED_IS_ON;
+		if (bdp->rev_id >= D101MA_REV_ID)
+			e100_led_control(bdp, PHY_82555_LED_ON_559);
+		else
+			e100_led_control(bdp, PHY_82555_LED_ON_PRE_559);
+	}
+
+	mod_timer(&bdp->blink_timer, jiffies + E100_BLINK_INTERVAL);
+}
+/**
+ * e100_ethtool_led_blink
+ * @dev: pointer to atapter's net_device struct
+ * @ifr: pointer to ioctl request structure
+ *
+ * Blink led ioctl handler. Initialtes blink timer and sleeps until
+ * blink period expires. Than it kills timer and returns. The led control
+ * is returned back to hardware when blink timer is killed.
+ */
+static int
+e100_ethtool_led_blink(struct net_device *dev, struct ifreq *ifr)
+{
+	struct e100_private *bdp;
+	struct ethtool_value ecmd;
+
+	bdp = dev->priv;
+
+	if (copy_from_user(&ecmd, ifr->ifr_data, sizeof (ecmd)))
+		return -EFAULT;
+
+	if(!bdp->blink_timer.function) {
+		init_timer(&bdp->blink_timer);
+		bdp->blink_timer.function = e100_led_blink_callback;
+		bdp->blink_timer.data = (unsigned long) bdp;
+	}
+
+	mod_timer(&bdp->blink_timer, jiffies);
+
+	set_current_state(TASK_INTERRUPTIBLE);
+
+	if ((!ecmd.data) || (ecmd.data > MAX_SCHEDULE_TIMEOUT / HZ))
+		ecmd.data = MAX_SCHEDULE_TIMEOUT / HZ;
+
+	schedule_timeout(ecmd.data * HZ);
+
+	del_timer_sync(&bdp->blink_timer);
+
+	e100_led_control(bdp, PHY_82555_LED_NORMAL_CONTROL);
+
+	return 0;
+}
+#endif
+
 static inline int __devinit
 e100_10BaseT_adapter(struct e100_private *bdp)
 {

drivers/net/e100/e100_proc.c

@@ -548,7 +548,7 @@ read_bundle_max_def(char *page, char **start, off_t off,
 	int len;
 
 	len = read_int_param(page, "CPU Saver Maximum Bundle",
-			     "Sets the value for CPU saver's maximum value",
+			     "Sets CPU saver's maximum value",
 			     E100_DEFAULT_CPUSAVER_BUNDLE_MAX, 0x1, 0xFFFF);
 
 	return generic_read(page, start, off, count, eof, len);

drivers/net/e100/e100_test.c

@@ -69,6 +69,7 @@ AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY OR
 TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE 
 OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
 *******************************************************************************/
+
 #include "e100.h"
 #include "e100_config.h"
 #ifdef ETHTOOL_TEST
@@ -458,10 +459,3 @@ e100_diag_loopback_free (struct e100_private *bdp)
 
 #endif
 
-
-
-
-
-
-
-

drivers/net/e1000/Makefile

+################################################################################
+#
+# This software program is available to you under a choice of one of two
+# licenses. You may choose to be licensed under either the GNU General Public
+# License 2.0, June 1991, available at http://www.fsf.org/copyleft/gpl.html,
+# or the Intel BSD + Patent License, the text of which follows:
+# 
+# Recipient has requested a license and Intel Corporation ("Intel") is willing
+# to grant a license for the software entitled Linux Base Driver for the
+# Intel(R) PRO/1000 Family of Adapters (e1000) (the "Software") being provided
+# by Intel Corporation. The following definitions apply to this license:
+# 
+# "Licensed Patents" means patent claims licensable by Intel Corporation which
+# are necessarily infringed by the use of sale of the Software alone or when
+# combined with the operating system referred to below.
+# 
+# "Recipient" means the party to whom Intel delivers this Software.
+# 
+# "Licensee" means Recipient and those third parties that receive a license to
+# any operating system available under the GNU General Public License 2.0 or
+# later.
+# 
+# Copyright (c) 1999 - 2002 Intel Corporation.
+# All rights reserved.
+# 
+# The license is provided to Recipient and Recipient's Licensees under the
+# following terms.
+# 
+# Redistribution and use in source and binary forms of the Software, with or
+# without modification, are permitted provided that the following conditions
+# are met:
+# 
+# Redistributions of source code of the Software may retain the above
+# copyright notice, this list of conditions and the following disclaimer.
+# 
+# Redistributions in binary form of the Software may reproduce the above
+# copyright notice, this list of conditions and the following disclaimer in
+# the documentation and/or materials provided with the distribution.
+# 
+# Neither the name of Intel Corporation nor the names of its contributors
+# shall be used to endorse or promote products derived from this Software
+# without specific prior written permission.
+# 
+# Intel hereby grants Recipient and Licensees a non-exclusive, worldwide,
+# royalty-free patent license under Licensed Patents to make, use, sell, offer
+# to sell, import and otherwise transfer the Software, if any, in source code
+# and object code form. This license shall include changes to the Software
+# that are error corrections or other minor changes to the Software that do
+# not add functionality or features when the Software is incorporated in any
+# version of an operating system that has been distributed under the GNU
+# General Public License 2.0 or later. This patent license shall apply to the
+# combination of the Software and any operating system licensed under the GNU
+# General Public License 2.0 or later if, at the time Intel provides the
+# Software to Recipient, such addition of the Software to the then publicly
+# available versions of such operating systems available under the GNU General
+# Public License 2.0 or later (whether in gold, beta or alpha form) causes
+# such combination to be covered by the Licensed Patents. The patent license
+# shall not apply to any other combinations which include the Software. NO
+# hardware per se is licensed hereunder.
+# 
+# THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
+# AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
+# IMPLIED WARRANTIES OF MECHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
+# ARE DISCLAIMED. IN NO EVENT SHALL INTEL OR IT CONTRIBUTORS BE LIABLE FOR ANY
+# DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
+# (INCLUDING, BUT NOT LIMITED, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
+# ANY LOSS OF USE; DATA, OR PROFITS; OR BUSINESS INTERUPTION) HOWEVER CAUSED
+# AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY OR
+# TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
+# OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
+#
+################################################################################
+
 #
 # Makefile for the Intel(R) PRO/1000 ethernet driver
 #

drivers/net/e1000/e1000.h

@@ -107,18 +107,21 @@
 #include <linux/udp.h>
 #include <net/pkt_sched.h>
 #include <linux/list.h>
-#include <asm/uaccess.h>
+#include <linux/reboot.h>
 #include <linux/ethtool.h>
 #ifdef NETIF_F_HW_VLAN_TX
 #include <linux/if_vlan.h>
 #endif
 
+#define BAR_0		0
+#define PCI_DMA_64BIT	0xffffffffffffffffULL
+#define PCI_DMA_32BIT	0x00000000ffffffffULL
+
+
 struct e1000_adapter;
 
 #include "e1000_hw.h"
 
-#define BAR_0 0
-
 #if DBG
 #define E1000_DBG(args...) printk(KERN_DEBUG "e1000: " args)
 #else
@@ -156,6 +159,7 @@ struct e1000_buffer {
 	struct sk_buff *skb;
 	uint64_t dma;
 	unsigned long length;
+	unsigned long time_stamp;
 };
 
 struct e1000_desc_ring {
@@ -204,10 +208,13 @@ struct e1000_adapter {
 	spinlock_t stats_lock;
 	atomic_t irq_sem;
 
+#ifdef ETHTOOL_PHYS_ID
+	struct timer_list blink_timer;
+	unsigned long led_status;
+#endif
+
 	/* TX */
 	struct e1000_desc_ring tx_ring;
-	unsigned long trans_finish;
-	spinlock_t tx_lock;
 	uint32_t txd_cmd;
 	int max_data_per_txd;
 
@@ -228,6 +235,9 @@ struct e1000_adapter {
 	struct e1000_hw_stats stats;
 	struct e1000_phy_info phy_info;
 	struct e1000_phy_stats phy_stats;
-};
 
+
+
+	uint32_t pci_state[16];
+};
 #endif /* _E1000_H_ */

drivers/net/e1000/e1000_ethtool.c

@@ -75,7 +75,6 @@
 
 #include "e1000.h"
 
-#include <linux/ethtool.h>
 #include <asm/uaccess.h>
 
 extern char e1000_driver_name[];
@@ -83,7 +82,6 @@ extern char e1000_driver_version[];
 
 extern int e1000_up(struct e1000_adapter *adapter);
 extern void e1000_down(struct e1000_adapter *adapter);
-extern void e1000_enable_WOL(struct e1000_adapter *adapter);
 
 static void
 e1000_ethtool_gset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
@@ -128,7 +126,11 @@ e1000_ethtool_gset(struct e1000_adapter *adapter, struct ethtool_cmd *ecmd)
 				     SUPPORTED_Autoneg);
 
 		ecmd->port = PORT_FIBRE;
-		ecmd->transceiver = XCVR_EXTERNAL;
+
+		if(hw->mac_type >= e1000_82545)
+			ecmd->transceiver = XCVR_INTERNAL;
+		else
+			ecmd->transceiver = XCVR_EXTERNAL;
 	}
 
 	if(netif_carrier_ok(adapter->netdev)) {
@@ -211,9 +213,37 @@ e1000_ethtool_gdrvinfo(struct e1000_adapter *adapter,
 	strncpy(drvinfo->version, e1000_driver_version, 32);
 	strncpy(drvinfo->fw_version, "", 32);
 	strncpy(drvinfo->bus_info, adapter->pdev->slot_name, 32);
+#define E1000_REGS_LEN 32
+	drvinfo->regdump_len  = E1000_REGS_LEN * sizeof(uint32_t);
 	drvinfo->eedump_len  = e1000_eeprom_size(&adapter->hw);
 }
 
+static void
+e1000_ethtool_gregs(struct e1000_adapter *adapter,
+                    struct ethtool_regs *regs, uint32_t *regs_buff)
+{
+	struct e1000_hw *hw = &adapter->hw;
+
+	regs->version = (1 << 24) | (hw->revision_id << 16) | hw->device_id;
+
+	regs_buff[0]  = E1000_READ_REG(hw, CTRL);
+	regs_buff[1]  = E1000_READ_REG(hw, STATUS);
+
+	regs_buff[2]  = E1000_READ_REG(hw, RCTL);
+	regs_buff[3]  = E1000_READ_REG(hw, RDLEN);
+	regs_buff[4]  = E1000_READ_REG(hw, RDH);
+	regs_buff[5]  = E1000_READ_REG(hw, RDT);
+	regs_buff[6]  = E1000_READ_REG(hw, RDTR);
+	
+	regs_buff[7]  = E1000_READ_REG(hw, TCTL);
+	regs_buff[8]  = E1000_READ_REG(hw, TDLEN);
+	regs_buff[9]  = E1000_READ_REG(hw, TDH);
+	regs_buff[10] = E1000_READ_REG(hw, TDT);
+	regs_buff[11] = E1000_READ_REG(hw, TIDV);
+
+	return;
+}
+
 static void
 e1000_ethtool_geeprom(struct e1000_adapter *adapter,
                       struct ethtool_eeprom *eeprom, uint16_t *eeprom_buff)
@@ -228,7 +258,7 @@ e1000_ethtool_geeprom(struct e1000_adapter *adapter,
 	if ((eeprom->offset + eeprom->len) > max_len)
 		eeprom->len = (max_len - eeprom->offset);
 
-	for(i = 0; i < max_len; i++)
+	for(i = 0; i < (max_len >> 1); i++)
 		e1000_read_eeprom(&adapter->hw, i, &eeprom_buff[i]);
 }
 
@@ -236,27 +266,50 @@ static void
 e1000_ethtool_gwol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
 {
 	struct e1000_hw *hw = &adapter->hw;
-	
-	if(hw->mac_type < e1000_82544) {
+
+	switch(adapter->hw.device_id) {
+	case E1000_DEV_ID_82542:
+	case E1000_DEV_ID_82543GC_FIBER:
+	case E1000_DEV_ID_82543GC_COPPER:
+	case E1000_DEV_ID_82544EI_FIBER:
+	default:
 		wol->supported = 0;
 		wol->wolopts   = 0;
 		return;
-	}
 
-	wol->supported = WAKE_PHY | WAKE_UCAST | 
-	                 WAKE_MCAST | WAKE_BCAST | WAKE_MAGIC;
-	
-	wol->wolopts = 0;
-	if(adapter->wol & E1000_WUFC_LNKC)
-		wol->wolopts |= WAKE_PHY;
-	if(adapter->wol & E1000_WUFC_EX)
-		wol->wolopts |= WAKE_UCAST;
-	if(adapter->wol & E1000_WUFC_MC)
-		wol->wolopts |= WAKE_MCAST;
-	if(adapter->wol & E1000_WUFC_BC)
-		wol->wolopts |= WAKE_BCAST;
-	if(adapter->wol & E1000_WUFC_MAG)
-		wol->wolopts |= WAKE_MAGIC;
+	case E1000_DEV_ID_82546EB_FIBER:
+		/* Wake events only supported on port A for dual fiber */
+		if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1) {
+			wol->supported = 0;
+			wol->wolopts   = 0;
+			return;
+		}
+		/* Fall Through */
+
+	case E1000_DEV_ID_82544EI_COPPER:
+	case E1000_DEV_ID_82544GC_COPPER:
+	case E1000_DEV_ID_82544GC_LOM:
+	case E1000_DEV_ID_82540EM:
+	case E1000_DEV_ID_82540EM_LOM:
+	case E1000_DEV_ID_82545EM_COPPER:
+	case E1000_DEV_ID_82545EM_FIBER:
+	case E1000_DEV_ID_82546EB_COPPER:
+		wol->supported = WAKE_PHY | WAKE_UCAST | 
+				 WAKE_MCAST | WAKE_BCAST | WAKE_MAGIC;
+		
+		wol->wolopts = 0;
+		if(adapter->wol & E1000_WUFC_LNKC)
+			wol->wolopts |= WAKE_PHY;
+		if(adapter->wol & E1000_WUFC_EX)
+			wol->wolopts |= WAKE_UCAST;
+		if(adapter->wol & E1000_WUFC_MC)
+			wol->wolopts |= WAKE_MCAST;
+		if(adapter->wol & E1000_WUFC_BC)
+			wol->wolopts |= WAKE_BCAST;
+		if(adapter->wol & E1000_WUFC_MAG)
+			wol->wolopts |= WAKE_MAGIC;
+		return;
+	}
 }
 
 static int
@@ -264,25 +317,95 @@ e1000_ethtool_swol(struct e1000_adapter *adapter, struct ethtool_wolinfo *wol)
 {
 	struct e1000_hw *hw = &adapter->hw;
 
-	if(hw->mac_type < e1000_82544)
+	switch(adapter->hw.device_id) {
+	case E1000_DEV_ID_82542:
+	case E1000_DEV_ID_82543GC_FIBER:
+	case E1000_DEV_ID_82543GC_COPPER:
+	case E1000_DEV_ID_82544EI_FIBER:
+	default:
 		return wol->wolopts ? -EOPNOTSUPP : 0;
 
-	adapter->wol = 0;
+	case E1000_DEV_ID_82546EB_FIBER:
+		/* Wake events only supported on port A for dual fiber */
+		if(E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)
+			return wol->wolopts ? -EOPNOTSUPP : 0;
+		/* Fall Through */
+
+	case E1000_DEV_ID_82544EI_COPPER:
+	case E1000_DEV_ID_82544GC_COPPER:
+	case E1000_DEV_ID_82544GC_LOM:
+	case E1000_DEV_ID_82540EM:
+	case E1000_DEV_ID_82540EM_LOM:
+	case E1000_DEV_ID_82545EM_COPPER:
+	case E1000_DEV_ID_82545EM_FIBER:
+	case E1000_DEV_ID_82546EB_COPPER:
+		if(wol->wolopts & WAKE_ARP)
+			return -EOPNOTSUPP;
+
+		adapter->wol = 0;
+
+		if(wol->wolopts & WAKE_PHY)
+			adapter->wol |= E1000_WUFC_LNKC;
+		if(wol->wolopts & WAKE_UCAST)
+			adapter->wol |= E1000_WUFC_EX;
+		if(wol->wolopts & WAKE_MCAST)
+			adapter->wol |= E1000_WUFC_MC;
+		if(wol->wolopts & WAKE_BCAST)
+			adapter->wol |= E1000_WUFC_BC;
+		if(wol->wolopts & WAKE_MAGIC)
+			adapter->wol |= E1000_WUFC_MAG;
+	}
+
+	return 0;
+}
+
+#ifdef	ETHTOOL_PHYS_ID
+
+/* toggle LED 4 times per second = 2 "blinks" per second */
+#define E1000_ID_INTERVAL	(HZ/4)
+
+/* bit defines for adapter->led_status */
+#define E1000_LED_ON		0
+
+static void
+e1000_led_blink_callback(unsigned long data)
+{
+	struct e1000_adapter *adapter = (struct e1000_adapter *) data;
+	
+	if(test_and_change_bit(E1000_LED_ON, &adapter->led_status))
+		e1000_led_off(&adapter->hw);
+	else
+		e1000_led_on(&adapter->hw);
+
+	mod_timer(&adapter->blink_timer, jiffies + E1000_ID_INTERVAL);
+}
 
-	if(wol->wolopts & WAKE_PHY)
-		adapter->wol |= E1000_WUFC_LNKC;
-	if(wol->wolopts & WAKE_UCAST)
-		adapter->wol |= E1000_WUFC_EX;
-	if(wol->wolopts & WAKE_MCAST)
-		adapter->wol |= E1000_WUFC_MC;
-	if(wol->wolopts & WAKE_BCAST)
-		adapter->wol |= E1000_WUFC_BC;
-	if(wol->wolopts & WAKE_MAGIC)
-		adapter->wol |= E1000_WUFC_MAG;
+static int
+e1000_ethtool_led_blink(struct e1000_adapter *adapter, struct ethtool_value *id)
+{
+	if(!adapter->blink_timer.function) {
+		init_timer(&adapter->blink_timer);
+		adapter->blink_timer.function = e1000_led_blink_callback;
+		adapter->blink_timer.data = (unsigned long) adapter;
+	}
+
+	e1000_setup_led(&adapter->hw);
+	mod_timer(&adapter->blink_timer, jiffies);
+	
+	set_current_state(TASK_INTERRUPTIBLE);
+	if(id->data)
+		schedule_timeout(id->data * HZ);
+	else
+		schedule_timeout(MAX_SCHEDULE_TIMEOUT);
+	
+	del_timer_sync(&adapter->blink_timer);
+	e1000_led_off(&adapter->hw);
+	clear_bit(E1000_LED_ON, &adapter->led_status);
+	e1000_cleanup_led(&adapter->hw);
 
-	e1000_enable_WOL(adapter);
 	return 0;
 }
+#endif	/* ETHTOOL_PHYS_ID */
 
 int
 e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr)
@@ -317,6 +440,22 @@ e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr)
 			return -EFAULT;
 		return 0;
 	}
+	case ETHTOOL_GREGS: {
+		struct ethtool_regs regs = {ETHTOOL_GREGS};
+		uint32_t regs_buff[E1000_REGS_LEN];
+
+		if(copy_from_user(&regs, addr, sizeof(regs)))
+			return -EFAULT;
+		e1000_ethtool_gregs(adapter, &regs, regs_buff);
+		if(copy_to_user(addr, &regs, sizeof(regs)))
+			return -EFAULT;
+
+		addr += offsetof(struct ethtool_regs, data);
+		if(copy_to_user(addr, regs_buff, regs.len))
+			return -EFAULT;
+
+		return 0;
+	}
 	case ETHTOOL_NWAY_RST: {
 		if(!capable(CAP_NET_ADMIN))
 			return -EPERM;
@@ -324,6 +463,14 @@ e1000_ethtool_ioctl(struct net_device *netdev, struct ifreq *ifr)
 		e1000_up(adapter);
 		return 0;
 	}
+#ifdef	ETHTOOL_PHYS_ID
+	case ETHTOOL_PHYS_ID: {
+		struct ethtool_value id;
+		if(copy_from_user(&id, addr, sizeof(id)))
+			return -EFAULT;
+		return e1000_ethtool_led_blink(adapter, &id);
+	}
+#endif	/* ETHTOOL_PHYS_ID */
 	case ETHTOOL_GLINK: {
 		struct ethtool_value link = {ETHTOOL_GLINK};
 		link.data = netif_carrier_ok(netdev);

drivers/net/e1000/e1000_hw.c

@@ -93,6 +93,7 @@ static void e1000_shift_out_ee_bits(struct e1000_hw *hw, uint16_t data, uint16_t
 static uint16_t e1000_shift_in_ee_bits(struct e1000_hw *hw);
 static void e1000_setup_eeprom(struct e1000_hw *hw);
 static void e1000_standby_eeprom(struct e1000_hw *hw);
+static int32_t e1000_id_led_init(struct e1000_hw * hw);
 
 /******************************************************************************
  * Reset the transmit and receive units; mask and clear all interrupts.
@@ -197,9 +198,20 @@ e1000_init_hw(struct e1000_hw *hw)
     uint32_t i;
     int32_t ret_val;
     uint16_t pci_cmd_word;
+    uint16_t pcix_cmd_word;
+    uint16_t pcix_stat_hi_word;
+    uint16_t cmd_mmrbc;
+    uint16_t stat_mmrbc;
 
     DEBUGFUNC("e1000_init_hw");
 
+    /* Initialize Identification LED */
+    ret_val = e1000_id_led_init(hw);
+    if(ret_val < 0) {
+	DEBUGOUT("Error Initializing Identification LED\n");
+	return ret_val;
+    }
+    
     /* Set the Media Type and exit with error if it is not valid. */
     if(hw->mac_type != e1000_82543) {
         /* tbi_compatibility is only valid on 82543 */
@@ -264,6 +276,21 @@ e1000_init_hw(struct e1000_hw *hw)
         E1000_WRITE_REG(hw, CTRL, ctrl | E1000_CTRL_PRIOR);
     }
 
+    /* Workaround for PCI-X problem when BIOS sets MMRBC incorrectly. */
+    if(hw->bus_type == e1000_bus_type_pcix) {
+        e1000_read_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
+        e1000_read_pci_cfg(hw, PCIX_STATUS_REGISTER_HI, &pcix_stat_hi_word);
+        cmd_mmrbc = (pcix_cmd_word & PCIX_COMMAND_MMRBC_MASK) >>
+            PCIX_COMMAND_MMRBC_SHIFT;
+        stat_mmrbc = (pcix_stat_hi_word & PCIX_STATUS_HI_MMRBC_MASK) >>
+            PCIX_STATUS_HI_MMRBC_SHIFT;
+        if(cmd_mmrbc > stat_mmrbc) {
+            pcix_cmd_word &= ~PCIX_COMMAND_MMRBC_MASK;
+            pcix_cmd_word |= stat_mmrbc << PCIX_COMMAND_MMRBC_SHIFT;
+            e1000_write_pci_cfg(hw, PCIX_COMMAND_REGISTER, &pcix_cmd_word);
+        }
+    }
+
     /* Call a subroutine to configure the link and setup flow control. */
     ret_val = e1000_setup_link(hw);
 
@@ -541,6 +568,7 @@ e1000_setup_copper_link(struct e1000_hw *hw)
      */
     if(hw->mac_type > e1000_82543) {
         ctrl |= E1000_CTRL_SLU;
+        ctrl &= ~(E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX);
         E1000_WRITE_REG(hw, CTRL, ctrl);
     } else {
         ctrl |= (E1000_CTRL_FRCSPD | E1000_CTRL_FRCDPX | E1000_CTRL_SLU);
@@ -2061,6 +2089,8 @@ e1000_detect_gig_phy(struct e1000_hw *hw)
         if(hw->phy_id == M88E1000_I_PHY_ID) match = TRUE;
         break;
     case e1000_82540:
+    case e1000_82545:
+    case e1000_82546:
         if(hw->phy_id == M88E1011_I_PHY_ID) match = TRUE;
         break;
     default:
@@ -2087,9 +2117,9 @@ e1000_phy_reset_dsp(struct e1000_hw *hw)
     DEBUGFUNC("e1000_phy_reset_dsp");
     
     do {
-        if(e1000_write_phy_reg(hw, 29, 0x1d) < 0) break;
-        if(e1000_write_phy_reg(hw, 30, 0xc1) < 0) break;
-        if(e1000_write_phy_reg(hw, 30, 0x00) < 0) break;
+        if(e1000_write_phy_reg(hw, 29, 0x001d) < 0) break;
+        if(e1000_write_phy_reg(hw, 30, 0x00c1) < 0) break;
+        if(e1000_write_phy_reg(hw, 30, 0x0000) < 0) break;
         ret_val = 0;
     } while(0);
 
@@ -2150,8 +2180,8 @@ e1000_phy_get_info(struct e1000_hw *hw,
             M88E1000_PSSR_MDIX_SHIFT;
         if(phy_data & M88E1000_PSSR_1000MBS) {
             /* Cable Length Estimation and Local/Remote Receiver Informatoion
-	     * are only valid at 1000 Mbps
-	     */
+             * are only valid at 1000 Mbps
+             */
             phy_info->cable_length = ((phy_data & M88E1000_PSSR_CABLE_LENGTH) >>
                                       M88E1000_PSSR_CABLE_LENGTH_SHIFT);
             if(e1000_read_phy_reg(hw, PHY_1000T_STATUS, &phy_data) < 0) 
@@ -2521,6 +2551,13 @@ e1000_read_mac_addr(struct e1000_hw * hw)
         hw->perm_mac_addr[i] = (uint8_t) (eeprom_data & 0x00FF);
         hw->perm_mac_addr[i+1] = (uint8_t) (eeprom_data >> 8);
     }
+    if((hw->mac_type == e1000_82546) &&
+       (E1000_READ_REG(hw, STATUS) & E1000_STATUS_FUNC_1)) {
+        if(hw->perm_mac_addr[5] & 0x01)
+            hw->perm_mac_addr[5] &= ~(0x01);
+        else
+            hw->perm_mac_addr[5] |= 0x01;
+    }
     for(i = 0; i < NODE_ADDRESS_SIZE; i++)
         hw->mac_addr[i] = hw->perm_mac_addr[i];
     return 0;
@@ -2785,6 +2822,74 @@ e1000_clear_vfta(struct e1000_hw *hw)
         E1000_WRITE_REG_ARRAY(hw, VFTA, offset, 0);
 }
 
+static int32_t
+e1000_id_led_init(struct e1000_hw * hw)
+{
+    uint32_t ledctl;
+    const uint32_t ledctl_mask = 0x000000FF;
+    const uint32_t ledctl_on = E1000_LEDCTL_MODE_LED_ON;
+    const uint32_t ledctl_off = E1000_LEDCTL_MODE_LED_OFF;
+    uint16_t eeprom_data, i, temp;
+    const uint16_t led_mask = 0x0F;
+	
+    DEBUGFUNC("e1000_id_led_init");
+    
+    if(hw->mac_type < e1000_82540) {
+	/* Nothing to do */
+	return 0;
+    }
+    
+    ledctl = E1000_READ_REG(hw, LEDCTL);
+    hw->ledctl_default = ledctl;
+    hw->ledctl_mode1 = hw->ledctl_default;
+    hw->ledctl_mode2 = hw->ledctl_default;
+        
+    if(e1000_read_eeprom(hw, EEPROM_ID_LED_SETTINGS, &eeprom_data) < 0) {
+        DEBUGOUT("EEPROM Read Error\n");
+        return -E1000_ERR_EEPROM;
+    }
+    if((eeprom_data== ID_LED_RESERVED_0000) || 
+       (eeprom_data == ID_LED_RESERVED_FFFF)) eeprom_data = ID_LED_DEFAULT;
+    for(i = 0; i < 4; i++) {
+        temp = (eeprom_data >> (i << 2)) & led_mask;
+        switch(temp) {
+	case ID_LED_ON1_DEF2:
+	case ID_LED_ON1_ON2:
+	case ID_LED_ON1_OFF2:
+            hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+            hw->ledctl_mode1 |= ledctl_on << (i << 3);
+            break;
+	case ID_LED_OFF1_DEF2:
+	case ID_LED_OFF1_ON2:
+	case ID_LED_OFF1_OFF2:
+            hw->ledctl_mode1 &= ~(ledctl_mask << (i << 3));
+            hw->ledctl_mode1 |= ledctl_off << (i << 3);
+            break;
+	default:
+	    /* Do nothing */
+	    break;
+	}
+	switch(temp) {
+	case ID_LED_DEF1_ON2:
+	case ID_LED_ON1_ON2:
+	case ID_LED_OFF1_ON2:
+            hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+            hw->ledctl_mode2 |= ledctl_on << (i << 3);
+            break;
+	case ID_LED_DEF1_OFF2:
+	case ID_LED_ON1_OFF2:
+	case ID_LED_OFF1_OFF2:
+            hw->ledctl_mode2 &= ~(ledctl_mask << (i << 3));
+            hw->ledctl_mode2 |= ledctl_off << (i << 3);
+            break;
+	default:
+	    /* Do nothing */
+	    break;
+	}
+    }
+    return 0;
+}
+
 /******************************************************************************
  * Prepares SW controlable LED for use and saves the current state of the LED.
  *
@@ -2807,22 +2912,24 @@ e1000_setup_led(struct e1000_hw *hw)
     case E1000_DEV_ID_82544GC_LOM:
         /* No setup necessary */
         break;
-    case E1000_DEV_ID_82540EM:
-    case E1000_DEV_ID_82540EM_LOM:
+    case E1000_DEV_ID_82545EM_FIBER:
+    case E1000_DEV_ID_82546EB_FIBER:
         ledctl = E1000_READ_REG(hw, LEDCTL);
         /* Save current LEDCTL settings */
-        hw->ledctl = ledctl;
-        /* Turn off LED2 and LED3 */
-        ledctl &= ~(E1000_LEDCTL_LED2_IVRT |
-                    E1000_LEDCTL_LED2_BLINK | 
-                    E1000_LEDCTL_LED2_MODE_MASK);
-        ledctl |= (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED2_MODE_SHIFT);
-        ledctl &= ~(E1000_LEDCTL_LED3_IVRT |
-                    E1000_LEDCTL_LED3_BLINK | 
-                    E1000_LEDCTL_LED3_MODE_MASK);
-        ledctl |= (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED3_MODE_SHIFT);
+        hw->ledctl_default = ledctl;
+        /* Turn off LED0 */
+        ledctl &= ~(E1000_LEDCTL_LED0_IVRT |
+                    E1000_LEDCTL_LED0_BLINK | 
+                    E1000_LEDCTL_LED0_MODE_MASK);
+        ledctl |= (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED0_MODE_SHIFT);
         E1000_WRITE_REG(hw, LEDCTL, ledctl);
         break;
+    case E1000_DEV_ID_82540EM:
+    case E1000_DEV_ID_82540EM_LOM:
+    case E1000_DEV_ID_82545EM_COPPER:
+    case E1000_DEV_ID_82546EB_COPPER:
+        E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
+        break;
     default:
         DEBUGOUT("Invalid device ID\n");
         return -E1000_ERR_CONFIG;
@@ -2852,8 +2959,12 @@ e1000_cleanup_led(struct e1000_hw *hw)
         break;
     case E1000_DEV_ID_82540EM:
     case E1000_DEV_ID_82540EM_LOM:
+    case E1000_DEV_ID_82545EM_COPPER:
+    case E1000_DEV_ID_82545EM_FIBER:
+    case E1000_DEV_ID_82546EB_COPPER:
+    case E1000_DEV_ID_82546EB_FIBER:
         /* Restore LEDCTL settings */
-        E1000_WRITE_REG(hw, LEDCTL, hw->ledctl);
+        E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_default);
         break;
     default:
         DEBUGOUT("Invalid device ID\n");
@@ -2871,7 +2982,6 @@ int32_t
 e1000_led_on(struct e1000_hw *hw)
 {
     uint32_t ctrl;
-    uint32_t ledctl;
 
     DEBUGFUNC("e1000_led_on");
 
@@ -2889,6 +2999,8 @@ e1000_led_on(struct e1000_hw *hw)
     case E1000_DEV_ID_82544EI_COPPER:
     case E1000_DEV_ID_82544GC_COPPER:
     case E1000_DEV_ID_82544GC_LOM:
+    case E1000_DEV_ID_82545EM_FIBER:
+    case E1000_DEV_ID_82546EB_FIBER:
         ctrl = E1000_READ_REG(hw, CTRL);
         /* Clear SW Defineable Pin 0 to turn on the LED */
         ctrl &= ~E1000_CTRL_SWDPIN0;
@@ -2897,11 +3009,9 @@ e1000_led_on(struct e1000_hw *hw)
         break;
     case E1000_DEV_ID_82540EM:
     case E1000_DEV_ID_82540EM_LOM:
-        ledctl = E1000_READ_REG(hw, LEDCTL);
-        /* Set LED 3 mode to on */
-        ledctl &= ~E1000_LEDCTL_LED3_MODE_MASK;
-        ledctl |= (E1000_LEDCTL_MODE_LED_ON << E1000_LEDCTL_LED3_MODE_SHIFT);
-        E1000_WRITE_REG(hw, LEDCTL, ledctl);
+    case E1000_DEV_ID_82545EM_COPPER:
+    case E1000_DEV_ID_82546EB_COPPER:
+        E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode2);
         break;
     default:
         DEBUGOUT("Invalid device ID\n");
@@ -2919,7 +3029,6 @@ int32_t
 e1000_led_off(struct e1000_hw *hw)
 {
     uint32_t ctrl;
-    uint32_t ledctl;
 
     DEBUGFUNC("e1000_led_off");
 
@@ -2937,6 +3046,8 @@ e1000_led_off(struct e1000_hw *hw)
     case E1000_DEV_ID_82544EI_COPPER:
     case E1000_DEV_ID_82544GC_COPPER:
     case E1000_DEV_ID_82544GC_LOM:
+    case E1000_DEV_ID_82545EM_FIBER:
+    case E1000_DEV_ID_82546EB_FIBER:
         ctrl = E1000_READ_REG(hw, CTRL);
         /* Set SW Defineable Pin 0 to turn off the LED */
         ctrl |= E1000_CTRL_SWDPIN0;
@@ -2945,11 +3056,9 @@ e1000_led_off(struct e1000_hw *hw)
         break;
     case E1000_DEV_ID_82540EM:
     case E1000_DEV_ID_82540EM_LOM:
-        ledctl = E1000_READ_REG(hw, LEDCTL);
-        /* Set LED 3 mode to off */
-        ledctl &= ~E1000_LEDCTL_LED3_MODE_MASK;
-        ledctl |= (E1000_LEDCTL_MODE_LED_OFF << E1000_LEDCTL_LED3_MODE_SHIFT);
-        E1000_WRITE_REG(hw, LEDCTL, ledctl);
+    case E1000_DEV_ID_82545EM_COPPER:
+    case E1000_DEV_ID_82546EB_COPPER:
+        E1000_WRITE_REG(hw, LEDCTL, hw->ledctl_mode1);
         break;
     default:
         DEBUGOUT("Invalid device ID\n");

drivers/net/e1000/e1000_hw.h

@@ -92,6 +92,8 @@ typedef enum {
     e1000_82543,
     e1000_82544,
     e1000_82540,
+    e1000_82545,
+    e1000_82546,
     e1000_num_macs
 } e1000_mac_type;
 
@@ -260,6 +262,7 @@ void e1000_reset_adaptive(struct e1000_hw *hw);
 void e1000_update_adaptive(struct e1000_hw *hw);
 void e1000_tbi_adjust_stats(struct e1000_hw *hw, struct e1000_hw_stats *stats, uint32_t frame_len, uint8_t * mac_addr);
 void e1000_get_bus_info(struct e1000_hw *hw);
+void e1000_read_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t * value);
 void e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t * value);
 
 /* PCI Device IDs */
@@ -272,7 +275,11 @@ void e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t * value);
 #define E1000_DEV_ID_82544GC_LOM    0x100D
 #define E1000_DEV_ID_82540EM        0x100E
 #define E1000_DEV_ID_82540EM_LOM    0x1015
-#define NUM_DEV_IDS 9
+#define E1000_DEV_ID_82545EM_COPPER 0x100F
+#define E1000_DEV_ID_82545EM_FIBER  0x1011
+#define E1000_DEV_ID_82546EB_COPPER 0x1010
+#define E1000_DEV_ID_82546EB_FIBER  0x1012
+#define NUM_DEV_IDS 13
 
 #define NODE_ADDRESS_SIZE 6
 #define ETH_LENGTH_OF_ADDRESS 6
@@ -882,7 +889,9 @@ struct e1000_hw {
     uint32_t num_mc_addrs;
     uint32_t collision_delta;
     uint32_t tx_packet_delta;
-    uint32_t ledctl;
+    uint32_t ledctl_default;
+    uint32_t ledctl_mode1;
+    uint32_t ledctl_mode2;
     uint16_t autoneg_advertised;
     uint16_t pci_cmd_word;
     uint16_t fc_high_water;
@@ -1324,10 +1333,28 @@ struct e1000_hw {
 #define EEPROM_EWDS_OPCODE  0x10 /* EERPOM erast/write disable */
 
 /* EEPROM Word Offsets */
-#define EEPROM_INIT_CONTROL1_REG 0x000A
-#define EEPROM_INIT_CONTROL2_REG 0x000F
-#define EEPROM_FLASH_VERSION     0x0032
-#define EEPROM_CHECKSUM_REG      0x003F
+#define EEPROM_ID_LED_SETTINGS     0x0004
+#define EEPROM_INIT_CONTROL1_REG   0x000A
+#define EEPROM_INIT_CONTROL2_REG   0x000F
+#define EEPROM_FLASH_VERSION       0x0032
+#define EEPROM_CHECKSUM_REG        0x003F
+
+/* Word definitions for ID LED Settings */
+#define ID_LED_RESERVED_0000 0x0000
+#define ID_LED_RESERVED_FFFF 0xFFFF
+#define ID_LED_DEFAULT       ((ID_LED_OFF1_ON2 << 12) | \
+		              (ID_LED_OFF1_OFF2 << 8) | \
+		              (ID_LED_DEF1_DEF2 << 4) | \
+			      (ID_LED_DEF1_DEF2))
+#define ID_LED_DEF1_DEF2     0x1
+#define ID_LED_DEF1_ON2      0x2
+#define ID_LED_DEF1_OFF2     0x3
+#define ID_LED_ON1_DEF2      0x4
+#define ID_LED_ON1_ON2       0x5
+#define ID_LED_ON1_OFF2      0x6
+#define ID_LED_OFF1_DEF2     0x7
+#define ID_LED_OFF1_ON2      0x8
+#define ID_LED_OFF1_OFF2     0x9
 
 /* Mask bits for fields in Word 0x0a of the EEPROM */
 #define EEPROM_WORD0A_ILOS   0x0010
@@ -1414,6 +1441,16 @@ struct e1000_hw {
 #define FC_DEFAULT_LO_THRESH        (0x4000)    /* 16KB */
 #define FC_DEFAULT_TX_TIMER         (0x100)     /* ~130 us */
 
+/* PCIX Config space */
+#define PCIX_COMMAND_REGISTER    0xE6
+#define PCIX_STATUS_REGISTER_LO  0xE8
+#define PCIX_STATUS_REGISTER_HI  0xEA
+
+#define PCIX_COMMAND_MMRBC_MASK      0x000C
+#define PCIX_COMMAND_MMRBC_SHIFT     0x2
+#define PCIX_STATUS_HI_MMRBC_MASK    0x0060
+#define PCIX_STATUS_HI_MMRBC_SHIFT   0x5
+
 
 /* The number of bits that we need to shift right to move the "pause"
  * bits from the EEPROM (bits 13:12) to the "pause" (bits 8:7) field

drivers/net/e1000/e1000_main.c

@@ -76,7 +76,7 @@
 
 char e1000_driver_name[] = "e1000";
 char e1000_driver_string[] = "Intel(R) PRO/1000 Network Driver";
-char e1000_driver_version[] = "4.2.8";
+char e1000_driver_version[] = "4.2.17-k1";
 char e1000_copyright[] = "Copyright (c) 1999-2002 Intel Corporation.";
 
 /* e1000_pci_tbl - PCI Device ID Table
@@ -114,6 +114,10 @@ static struct pci_device_id e1000_pci_tbl[] __devinitdata = {
 	{0x8086, 0x100C, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
 	{0x8086, 0x100D, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
 	{0x8086, 0x100E, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{0x8086, 0x100F, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{0x8086, 0x1011, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{0x8086, 0x1010, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
+	{0x8086, 0x1012, PCI_ANY_ID, PCI_ANY_ID, 0, 0, 0},
 	/* required last entry */
 	{0,}
 };
@@ -126,7 +130,7 @@ static char *e1000_strings[] = {
 	"IBM Mobile, Desktop & Server Adapters"
 };
 
-/* e1000_main.c Function Prototypes */
+/* Local Function Prototypes */
 
 int e1000_up(struct e1000_adapter *adapter);
 void e1000_down(struct e1000_adapter *adapter);
@@ -169,13 +173,24 @@ static void e1000_leave_82542_rst(struct e1000_adapter *adapter);
 static inline void e1000_rx_checksum(struct e1000_adapter *adapter,
                                      struct e1000_rx_desc *rx_desc,
                                      struct sk_buff *skb);
-void e1000_enable_WOL(struct e1000_adapter *adapter);
 #ifdef NETIF_F_HW_VLAN_TX
 static void e1000_vlan_rx_register(struct net_device *netdev, struct vlan_group *grp);
 static void e1000_vlan_rx_add_vid(struct net_device *netdev, uint16_t vid);
 static void e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid);
 #endif
 
+static int e1000_notify_reboot(struct notifier_block *, unsigned long event, void *ptr);
+static int e1000_suspend(struct pci_dev *pdev, uint32_t state);
+#ifdef CONFIG_PM
+static int e1000_resume(struct pci_dev *pdev);
+#endif
+
+struct notifier_block e1000_notifier = {
+	notifier_call:	e1000_notify_reboot,
+	next:		NULL,
+	priority:	0
+};
+
 /* Exported from other modules */
 
 extern void e1000_check_options(struct e1000_adapter *adapter);
@@ -189,8 +204,10 @@ static struct pci_driver e1000_driver = {
 	probe:    e1000_probe,
 	remove:   __devexit_p(e1000_remove),
 	/* Power Managment Hooks */
-	suspend:  NULL,
-	resume:   NULL
+#ifdef CONFIG_PM
+	suspend:  e1000_suspend,
+	resume:   e1000_resume
+#endif
 };
 
 MODULE_AUTHOR("Intel Corporation, <linux.nics@intel.com>");
@@ -207,12 +224,16 @@ MODULE_LICENSE("Dual BSD/GPL");
 static int __init
 e1000_init_module(void)
 {
+	int ret;
 	printk(KERN_INFO "%s - version %s\n",
 	       e1000_driver_string, e1000_driver_version);
 
 	printk(KERN_INFO "%s\n", e1000_copyright);
 
-	return pci_module_init(&e1000_driver);
+	ret = pci_module_init(&e1000_driver);
+	if(ret >= 0)
+		register_reboot_notifier(&e1000_notifier);
+	return ret;
 }
 
 module_init(e1000_init_module);
@@ -227,6 +248,7 @@ module_init(e1000_init_module);
 static void __exit
 e1000_exit_module(void)
 {
+	unregister_reboot_notifier(&e1000_notifier);
 	pci_unregister_driver(&e1000_driver);
 }
 
@@ -290,11 +312,11 @@ e1000_reset(struct e1000_adapter *adapter)
 
 	adapter->hw.fc = adapter->hw.original_fc;
 	e1000_reset_hw(&adapter->hw);
+	if(adapter->hw.mac_type >= e1000_82544)
+		E1000_WRITE_REG(&adapter->hw, WUC, 0);
 	e1000_init_hw(&adapter->hw);
 	e1000_reset_adaptive(&adapter->hw);
 	e1000_phy_get_info(&adapter->hw, &adapter->phy_info);
-
-	e1000_enable_WOL(adapter);
 }
 
 /**
@@ -324,10 +346,10 @@ e1000_probe(struct pci_dev *pdev,
 	if((i = pci_enable_device(pdev)))
 		return i;
 
-	if(!(i = pci_set_dma_mask(pdev, (u64) 0xffffffffffffffff))) {
+	if(!(i = pci_set_dma_mask(pdev, PCI_DMA_64BIT))) {
 		pci_using_dac = 1;
 	} else {
-		if((i = pci_set_dma_mask(pdev, (u64) 0xffffffff))) {
+		if((i = pci_set_dma_mask(pdev, PCI_DMA_32BIT))) {
 			E1000_ERR("No usable DMA configuration, aborting\n");
 			return i;
 		}
@@ -403,8 +425,10 @@ e1000_probe(struct pci_dev *pdev,
 
 	/* make sure the EEPROM is good */
 
-	if(e1000_validate_eeprom_checksum(&adapter->hw) < 0)
+	if(e1000_validate_eeprom_checksum(&adapter->hw) < 0) {
+		printk(KERN_ERR "The EEPROM Checksum Is Not Valid\n");
 		goto err_eeprom;
+	}
 
 	/* copy the MAC address out of the EEPROM */
 
@@ -437,7 +461,7 @@ e1000_probe(struct pci_dev *pdev,
 	register_netdev(netdev);
 
 	/* we're going to reset, so assume we have no link for now */
-	
+
 	netif_carrier_off(netdev);
 	netif_stop_queue(netdev);
 
@@ -445,6 +469,15 @@ e1000_probe(struct pci_dev *pdev,
 	e1000_check_options(adapter);
 	e1000_proc_dev_setup(adapter);
 
+	/* Initial Wake on LAN setting
+	 * If APM wake is enabled in the EEPROM,
+	 * enable the ACPI Magic Packet filter
+	 */
+
+	if((adapter->hw.mac_type >= e1000_82544) &&
+	   (E1000_READ_REG(&adapter->hw, WUC) & E1000_WUC_APME))
+		adapter->wol |= E1000_WUFC_MAG;
+
 	/* reset the hardware with the new settings */
 
 	e1000_reset(adapter);
@@ -555,6 +588,14 @@ e1000_sw_init(struct e1000_adapter *adapter)
 	case E1000_DEV_ID_82540EM:
 		hw->mac_type = e1000_82540;
 		break;
+	case E1000_DEV_ID_82545EM_COPPER:
+	case E1000_DEV_ID_82545EM_FIBER:
+		hw->mac_type = e1000_82545;
+		break;
+	case E1000_DEV_ID_82546EB_COPPER:
+	case E1000_DEV_ID_82546EB_FIBER:
+		hw->mac_type = e1000_82546;
+		break;
 	default:
 		/* should never have loaded on this device */
 		BUG();
@@ -590,7 +631,6 @@ e1000_sw_init(struct e1000_adapter *adapter)
 	hw->adaptive_ifs = TRUE;
 
 	atomic_set(&adapter->irq_sem, 1);
-	spin_lock_init(&adapter->tx_lock);
 	spin_lock_init(&adapter->stats_lock);
 }
 
@@ -715,7 +755,7 @@ e1000_configure_tx(struct e1000_adapter *adapter)
 	uint32_t tdlen = adapter->tx_ring.count * sizeof(struct e1000_tx_desc);
 	uint32_t tctl, tipg;
 
-	E1000_WRITE_REG(&adapter->hw, TDBAL, (tdba & 0x00000000FFFFFFFF));
+	E1000_WRITE_REG(&adapter->hw, TDBAL, (tdba & 0x00000000ffffffffULL));
 	E1000_WRITE_REG(&adapter->hw, TDBAH, (tdba >> 32));
 
 	E1000_WRITE_REG(&adapter->hw, TDLEN, tdlen);
@@ -752,7 +792,7 @@ e1000_configure_tx(struct e1000_adapter *adapter)
 
 	tctl = E1000_READ_REG(&adapter->hw, TCTL);
 
-	tctl &= ~E1000_TCTL_CT;	
+	tctl &= ~E1000_TCTL_CT;
 	tctl |= E1000_TCTL_EN | E1000_TCTL_PSP |
 	       (E1000_COLLISION_THRESHOLD << E1000_CT_SHIFT);
 
@@ -875,7 +915,7 @@ e1000_configure_rx(struct e1000_adapter *adapter)
 
 	/* set the Receive Delay Timer Register */
 
-	if(adapter->hw.mac_type == e1000_82540) {
+	if(adapter->hw.mac_type >= e1000_82540) {
 		E1000_WRITE_REG(&adapter->hw, RADV, adapter->rx_int_delay);
 		E1000_WRITE_REG(&adapter->hw, RDTR, 64);
 
@@ -891,7 +931,7 @@ e1000_configure_rx(struct e1000_adapter *adapter)
 
 	/* Setup the Base and Length of the Rx Descriptor Ring */
 
-	E1000_WRITE_REG(&adapter->hw, RDBAL, (rdba & 0x00000000FFFFFFFF));
+	E1000_WRITE_REG(&adapter->hw, RDBAL, (rdba & 0x00000000ffffffffULL));
 	E1000_WRITE_REG(&adapter->hw, RDBAH, (rdba >> 32));
 
 	E1000_WRITE_REG(&adapter->hw, RDLEN, rdlen);
@@ -1212,6 +1252,8 @@ e1000_watchdog(unsigned long data)
 {
 	struct e1000_adapter *adapter = (struct e1000_adapter *) data;
 	struct net_device *netdev = adapter->netdev;
+	struct e1000_desc_ring *txdr = &adapter->tx_ring;
+	int i;
 
 	e1000_check_for_link(&adapter->hw);
 
@@ -1228,7 +1270,6 @@ e1000_watchdog(unsigned long data)
 			       "Full Duplex" : "Half Duplex");
 
 			netif_carrier_on(netdev);
-			adapter->trans_finish = jiffies;
 			netif_wake_queue(netdev);
 			mod_timer(&adapter->phy_info_timer, jiffies + 2 * HZ);
 		}
@@ -1248,6 +1289,13 @@ e1000_watchdog(unsigned long data)
 	e1000_update_stats(adapter);
 	e1000_update_adaptive(&adapter->hw);
 
+	/* Early detection of hung controller */
+	i = txdr->next_to_clean;
+	if(txdr->buffer_info[i].dma &&
+	   time_after(jiffies, txdr->buffer_info[i].time_stamp + HZ) &&
+	   !(E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_TXOFF))
+		netif_stop_queue(netdev);
+
 	/* Reset the timer */
 	mod_timer(&adapter->watchdog_timer, jiffies + 2 * HZ);
 }
@@ -1310,6 +1358,7 @@ e1000_tx_map(struct e1000_adapter *adapter, struct sk_buff *skb)
 				skb->data + offset,
 				size,
 				PCI_DMA_TODEVICE);
+		tx_ring->buffer_info[i].time_stamp = jiffies;
 
 		len -= size;
 		offset += size;
@@ -1388,20 +1437,11 @@ static int
 e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 {
 	struct e1000_adapter *adapter = netdev->priv;
-	unsigned long flags;
 	int tx_flags = 0, count;
 
 	int f;
 
 
-	if(time_after(netdev->trans_start, adapter->trans_finish + HZ) &&
-	   !(E1000_READ_REG(&adapter->hw, STATUS) & E1000_STATUS_TXOFF)) {
-
-		adapter->trans_finish = jiffies;
-		netif_stop_queue(netdev);
-		return 1;
-	}
-
 	count = TXD_USE_COUNT(skb->len - skb->data_len,
 	                      adapter->max_data_per_txd);
 	for(f = 0; f < skb_shinfo(skb)->nr_frags; f++)
@@ -1410,14 +1450,10 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 	if(skb->ip_summed == CHECKSUM_HW)
 		count++;
 
-	spin_lock_irqsave(&adapter->tx_lock, flags);
-	e1000_clean_tx_irq(adapter);
 	if(E1000_DESC_UNUSED(&adapter->tx_ring) < count) {
 		netif_stop_queue(netdev);
-		spin_unlock_irqrestore(&adapter->tx_lock, flags);
 		return 1;
 	}
-	spin_unlock_irqrestore(&adapter->tx_lock, flags);
 
 	if(e1000_tx_csum(adapter, skb))
 		tx_flags |= E1000_TX_FLAGS_CSUM;
@@ -1428,7 +1464,7 @@ e1000_xmit_frame(struct sk_buff *skb, struct net_device *netdev)
 		tx_flags |= (vlan_tx_tag_get(skb) << E1000_TX_FLAGS_VLAN_SHIFT);
 	}
 #endif
-	
+
 	count = e1000_tx_map(adapter, skb);
 
 	e1000_tx_queue(adapter, count, tx_flags);
@@ -1701,12 +1737,7 @@ e1000_intr(int irq, void *data, struct pt_regs *regs)
 		}
 
 		e1000_clean_rx_irq(adapter);
-
-		if((icr & E1000_ICR_TXDW) && spin_trylock(&adapter->tx_lock)) {
-			e1000_clean_tx_irq(adapter);
-			spin_unlock(&adapter->tx_lock);
-		}
-
+		e1000_clean_tx_irq(adapter);
 		i--;
 
 	}
@@ -1753,8 +1784,6 @@ e1000_clean_tx_irq(struct e1000_adapter *adapter)
 
 		i = (i + 1) % tx_ring->count;
 		tx_desc = E1000_TX_DESC(*tx_ring, i);
-
-		adapter->trans_finish = jiffies;
 	}
 
 	tx_ring->next_to_clean = i;
@@ -1893,9 +1922,6 @@ e1000_alloc_rx_buffers(struct e1000_adapter *adapter)
 	int reserve_len;
 	int i;
 
-	if(!netif_running(netdev))
-		return;
-
 	reserve_len = 2;
 
 	i = rx_ring->next_to_use;
@@ -1991,32 +2017,16 @@ e1000_rx_checksum(struct e1000_adapter *adapter,
 	}
 }
 
-/**
- * e1000_enable_WOL - Wake On Lan Support (Magic Pkt)
- * @adapter: Adapter structure
- **/
-
 void
-e1000_enable_WOL(struct e1000_adapter *adapter)
+e1000_read_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value)
 {
-	uint32_t wuc;
-
-	if(adapter->hw.mac_type < e1000_82544)
-		return;
-
-	if(adapter->wol) {
-		wuc = E1000_WUC_APME | E1000_WUC_PME_EN |
-		      E1000_WUC_PME_STATUS | E1000_WUC_APMPME;
-
-		E1000_WRITE_REG(&adapter->hw, WUC, wuc);
+	struct e1000_adapter *adapter = hw->back;
 
-		E1000_WRITE_REG(&adapter->hw, WUFC, adapter->wol);
-	}
+	pci_read_config_word(adapter->pdev, reg, value);
 }
 
 void
-e1000_write_pci_cfg(struct e1000_hw *hw,
-                    uint32_t reg, uint16_t *value)
+e1000_write_pci_cfg(struct e1000_hw *hw, uint32_t reg, uint16_t *value)
 {
 	struct e1000_adapter *adapter = hw->back;
 
@@ -2086,10 +2096,10 @@ e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid)
 	uint32_t vfta, index;
 
 	e1000_irq_disable(adapter);
-	
+
 	if(adapter->vlgrp)
 		adapter->vlgrp->vlan_devices[vid] = NULL;
-	
+
 	e1000_irq_enable(adapter);
 
 	/* remove VID from filter table*/
@@ -2101,4 +2111,93 @@ e1000_vlan_rx_kill_vid(struct net_device *netdev, uint16_t vid)
 }
 #endif
 
+static int
+e1000_notify_reboot(struct notifier_block *nb, unsigned long event, void *p)
+{
+	struct pci_dev *pdev = NULL;
+
+	switch(event) {
+	case SYS_DOWN:
+	case SYS_HALT:
+	case SYS_POWER_OFF:
+		pci_for_each_dev(pdev) {
+			if(pci_dev_driver(pdev) == &e1000_driver)
+				e1000_suspend(pdev, 3);
+		}
+	}
+	return NOTIFY_DONE;
+}
+
+static int
+e1000_suspend(struct pci_dev *pdev, uint32_t state)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct e1000_adapter *adapter = netdev->priv;
+	uint32_t ctrl, ctrl_ext, rctl;
+
+	netif_device_detach(netdev);
+
+	if(netif_running(netdev))
+		e1000_down(adapter);
+
+	if(adapter->wol) {
+		e1000_setup_rctl(adapter);
+		e1000_set_multi(netdev);
+
+		if(adapter->wol & E1000_WUFC_MC) {
+			rctl = E1000_READ_REG(&adapter->hw, RCTL);
+			rctl |= E1000_RCTL_MPE;
+			E1000_WRITE_REG(&adapter->hw, RCTL, rctl);
+		}
+
+		if(adapter->hw.media_type == e1000_media_type_fiber) {
+			#define E1000_CTRL_ADVD3WUC 0x00100000
+			ctrl = E1000_READ_REG(&adapter->hw, CTRL);
+			ctrl |= E1000_CTRL_ADVD3WUC;
+			E1000_WRITE_REG(&adapter->hw, CTRL, ctrl);
+
+			ctrl_ext = E1000_READ_REG(&adapter->hw, CTRL_EXT);
+        		ctrl_ext |= E1000_CTRL_EXT_SDP7_DATA;
+			E1000_WRITE_REG(&adapter->hw, CTRL_EXT, ctrl_ext);
+		}
+
+		E1000_WRITE_REG(&adapter->hw, WUC, 0);
+		E1000_WRITE_REG(&adapter->hw, WUFC, adapter->wol);
+		pci_enable_wake(pdev, 3, 1);
+	} else {
+		E1000_WRITE_REG(&adapter->hw, WUC, 0);
+		E1000_WRITE_REG(&adapter->hw, WUFC, 0);
+		pci_enable_wake(pdev, 3, 0);
+	}
+
+	pci_save_state(pdev, adapter->pci_state);
+	pci_set_power_state(pdev, 3);
+
+	return 0;
+}
+
+#ifdef CONFIG_PM
+static int
+e1000_resume(struct pci_dev *pdev)
+{
+	struct net_device *netdev = pci_get_drvdata(pdev);
+	struct e1000_adapter *adapter = netdev->priv;
+
+	pci_set_power_state(pdev, 0);
+	pci_restore_state(pdev, adapter->pci_state);
+	pci_enable_wake(pdev, 0, 0);
+
+	/* Clear the wakeup status bits */
+
+	E1000_WRITE_REG(&adapter->hw, WUS, ~0);
+
+	if(netif_running(netdev))
+		e1000_up(adapter);
+
+	netif_device_attach(netdev);
+
+	return 0;
+}
+#endif
+
 /* e1000_main.c */

drivers/net/e1000/e1000_osdep.h

@@ -86,12 +86,14 @@
 #include <linux/interrupt.h>
 
 #define usec_delay(x) udelay(x)
+#ifndef msec_delay
 #define msec_delay(x)	do { if(in_interrupt()) { \
 	                	mdelay(x); \
 			} else { \
 				set_current_state(TASK_UNINTERRUPTIBLE); \
 				schedule_timeout((x * HZ)/1000); \
 			} } while(0)
+#endif
 
 #define PCI_COMMAND_REGISTER   PCI_COMMAND
 #define CMD_MEM_WRT_INVALIDATE PCI_COMMAND_INVALIDATE

drivers/net/eepro100.c

@@ -524,10 +524,8 @@ static const char is_mii[] = { 0, 1, 1, 0, 1, 1, 0, 1 };
 static int eepro100_init_one(struct pci_dev *pdev,
 		const struct pci_device_id *ent);
 static void eepro100_remove_one (struct pci_dev *pdev);
-#ifdef CONFIG_PM
 static int eepro100_suspend (struct pci_dev *pdev, u32 state);
 static int eepro100_resume (struct pci_dev *pdev);
-#endif
 
 static int do_eeprom_cmd(long ioaddr, int cmd, int cmd_len);
 static int mdio_read(long ioaddr, int phy_id, int location);

drivers/net/pcnet32.c

@@ -845,8 +845,9 @@ pcnet32_open(struct net_device *dev)
 	    if (lp->options == (PCNET32_PORT_FD | PCNET32_PORT_AUI))
 		val |= 2;
 	} else if (lp->options & PCNET32_PORT_ASEL) {
-	/* workaround for xSeries250 */
-	    val |= 3;
+	/* workaround of xSeries250, turn on for 79C975 only */
+	    i = ((lp->a.read_csr(ioaddr, 88) | (lp->a.read_csr(ioaddr,89) << 16)) >> 12) & 0xffff;
+	    if (i == 0x2627) val |= 3;
 	}
 	lp->a.write_bcr (ioaddr, 9, val);
     }

include/linux/ethtool.h

@@ -4,6 +4,9 @@
  * Copyright (C) 1998 David S. Miller (davem@redhat.com)
  * Copyright 2001 Jeff Garzik <jgarzik@mandrakesoft.com>
  * Portions Copyright 2001 Sun Microsystems (thockin@sun.com)
+ * Portions Copyright 2002 Intel (eli.kupermann@intel.com,
+ *                                christopher.leech@intel.com,
+ *                                scott.feldman@intel.com)
  */
 
 #ifndef _LINUX_ETHTOOL_H
@@ -268,6 +271,7 @@ struct ethtool_test {
 					    * (ethtool_value), priv. */
 #define ETHTOOL_TEST		0x0000001a /* execute NIC self-test, priv. */
 #define ETHTOOL_GSTRINGS	0x0000001b /* get specified string set */
+#define ETHTOOL_PHYS_ID		0x0000001c /* identify the NIC */
 
 /* compatibility with older code */
 #define SPARC_ETH_GSET		ETHTOOL_GSET