Merge remote-tracking branch 'arm-soc/arm/drivers' into HEAD

Documentation/ABI/testing/debugfs-moxtet

+What:		/sys/kernel/debug/moxtet/input
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Read input from the shift registers, in hexadecimal.
+		Returns N+1 bytes, where N is the number of Moxtet connected
+		modules. The first byte is from the CPU board itself.
+		Example: 101214
+			 10: CPU board with SD card
+			 12: 2 = PCIe module, 1 = IRQ not active
+			 14: 4 = Peridot module, 1 = IRQ not active
+
+What:		/sys/kernel/debug/moxtet/output
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(RW) Read last written value to the shift registers, in
+		hexadecimal, or write values to the shift registers, also
+		in hexadecimal.
+		Example: 0102
+			 01: 01 was last written, or is to be written, to the
+			     first module's shift register
+			 02: the same for second module

Documentation/ABI/testing/sysfs-bus-moxtet-devices

+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_description
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module description. Format: string
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_id
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module ID. Format: %x
+
+What:		/sys/bus/moxtet/devices/moxtet-<name>.<addr>/module_name
+Date:		March 2019
+KernelVersion:	5.3
+Contact:	Marek Behún <marek.behun@nic.cz>
+Description:	(R) Moxtet module name. Format: string

Documentation/devicetree/bindings/arm/arm,scmi.txt

@@ -73,6 +73,16 @@ Required properties:
 			 as used by the firmware. Refer to  platform details
 			 for your implementation for the IDs to use.
 
+Reset signal bindings for the reset domains based on SCMI Message Protocol
+------------------------------------------------------------
+
+This binding for the SCMI reset domain providers uses the generic reset
+signal binding[5].
+
+Required properties:
+ - #reset-cells : Should be 1. Contains the reset domain ID value used
+		  by SCMI commands.
+
 SRAM and Shared Memory for SCMI
 -------------------------------
 
@@ -93,6 +103,7 @@ Required sub-node properties:
 [2] Documentation/devicetree/bindings/power/power_domain.txt
 [3] Documentation/devicetree/bindings/thermal/thermal.txt
 [4] Documentation/devicetree/bindings/sram/sram.txt
+[5] Documentation/devicetree/bindings/reset/reset.txt
 
 Example:
 
@@ -152,6 +163,11 @@ firmware {
 			reg = <0x15>;
 			#thermal-sensor-cells = <1>;
 		};
+
+		scmi_reset: protocol@16 {
+			reg = <0x16>;
+			#reset-cells = <1>;
+		};
 	};
 };
 
@@ -166,6 +182,7 @@ hdlcd@7ff60000 {
 	reg = <0 0x7ff60000 0 0x1000>;
 	clocks = <&scmi_clk 4>;
 	power-domains = <&scmi_devpd 1>;
+	resets = <&scmi_reset 10>;
 };
 
 thermal-zones {

Documentation/devicetree/bindings/bus/moxtet.txt

+Turris Mox module status and configuration bus (over SPI)
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet"
+ - #address-cells	: Has to be 1
+ - #size-cells		: Has to be 0
+ - spi-cpol		: Required inverted clock polarity
+ - spi-cpha		: Required shifted clock phase
+ - interrupts		: Must contain reference to the shared interrupt line
+ - interrupt-controller	: Required
+ - #interrupt-cells	: Has to be 1
+
+For other required and optional properties of SPI slave nodes please refer to
+../spi/spi-bus.txt.
+
+Required properties of subnodes:
+ - reg			: Should be position on the Moxtet bus (how many Moxtet
+			  modules are between this module and CPU module, so
+			  either 0 or a positive integer)
+
+The driver finds the devices connected to the bus by itself, but it may be
+needed to reference some of them from other parts of the device tree. In that
+case the devices can be defined as subnodes of the moxtet node.
+
+Example:
+
+	moxtet@1 {
+		compatible = "cznic,moxtet";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		reg = <1>;
+		spi-max-frequency = <10000000>;
+		spi-cpol;
+		spi-cpha;
+		interrupt-controller;
+		#interrupt-cells = <1>;
+		interrupt-parent = <&gpiosb>;
+		interrupts = <5 IRQ_TYPE_EDGE_FALLING>;
+
+		moxtet_sfp: gpio@0 {
+			compatible = "cznic,moxtet-gpio";
+			gpio-controller;
+			#gpio-cells = <2>;
+			reg = <0>;
+		}
+	};

Documentation/devicetree/bindings/gpio/gpio-moxtet.txt

+Turris Mox Moxtet GPIO expander via Moxtet bus
+
+Required properties:
+ - compatible		: Should be "cznic,moxtet-gpio".
+ - gpio-controller	: Marks the device node as a GPIO controller.
+ - #gpio-cells		: Should be two. For consumer use see gpio.txt.
+
+Other properties are required for a Moxtet bus device, please refer to
+Documentation/devicetree/bindings/bus/moxtet.txt.
+
+Example:
+
+	moxtet_sfp: gpio@0 {
+		compatible = "cznic,moxtet-gpio";
+		gpio-controller;
+		#gpio-cells = <2>;
+		reg = <0>;
+	}

Documentation/devicetree/bindings/reset/fsl,imx7-src.txt

@@ -8,6 +8,7 @@ Required properties:
 - compatible:
 	- For i.MX7 SoCs should be "fsl,imx7d-src", "syscon"
 	- For i.MX8MQ SoCs should be "fsl,imx8mq-src", "syscon"
+	- For i.MX8MM SoCs should be "fsl,imx8mm-src", "fsl,imx8mq-src", "syscon"
 - reg: should be register base and length as documented in the
   datasheet
 - interrupts: Should contain SRC interrupt
@@ -46,5 +47,6 @@ Example:
 
 
 For list of all valid reset indices see
-<dt-bindings/reset/imx7-reset.h> for i.MX7 and
-<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ
+<dt-bindings/reset/imx7-reset.h> for i.MX7,
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MQ and
+<dt-bindings/reset/imx8mq-reset.h> for i.MX8MM

Documentation/devicetree/bindings/reset/snps,dw-reset.txt

+Synopsys DesignWare Reset controller
+=======================================
+
+Please also refer to reset.txt in this directory for common reset
+controller binding usage.
+
+Required properties:
+
+- compatible: should be one of the following.
+	"snps,dw-high-reset" - for active high configuration
+	"snps,dw-low-reset" - for active low configuration
+
+- reg: physical base address of the controller and length of memory mapped
+	region.
+
+- #reset-cells: must be 1.
+
+example:
+
+	dw_rst_1: reset-controller@0000 {
+		compatible = "snps,dw-high-reset";
+		reg = <0x0000 0x4>;
+		#reset-cells = <1>;
+	};
+
+	dw_rst_2: reset-controller@1000 {i
+		compatible = "snps,dw-low-reset";
+		reg = <0x1000 0x8>;
+		#reset-cells = <1>;
+	};

Documentation/devicetree/bindings/soc/fsl/cpm_qe/qe.txt

@@ -18,7 +18,8 @@ Required properties:
 - reg : offset and length of the device registers.
 - bus-frequency : the clock frequency for QUICC Engine.
 - fsl,qe-num-riscs: define how many RISC engines the QE has.
-- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use for the
+- fsl,qe-snums: This property has to be specified as '/bits/ 8' value,
+  defining the array of serial number (SNUM) values for the virtual
   threads.
 
 Optional properties:
@@ -34,6 +35,11 @@ Recommended properties
 - brg-frequency : the internal clock source frequency for baud-rate
   generators in Hz.
 
+Deprecated properties
+- fsl,qe-num-snums: define how many serial number(SNUM) the QE can use
+  for the threads. Use fsl,qe-snums instead to not only specify the
+  number of snums, but also their values.
+
 Example:
      qe@e0100000 {
 	#address-cells = <1>;
@@ -44,6 +50,11 @@ Example:
 	reg = <e0100000 480>;
 	brg-frequency = <0>;
 	bus-frequency = <179A7B00>;
+	fsl,qe-snums = /bits/ 8 <
+		0x04 0x05 0x0C 0x0D 0x14 0x15 0x1C 0x1D
+		0x24 0x25 0x2C 0x2D 0x34 0x35 0x88 0x89
+		0x98 0x99 0xA8 0xA9 0xB8 0xB9 0xC8 0xC9
+		0xD8 0xD9 0xE8 0xE9>;
      }
 
 * Multi-User RAM (MURAM)

MAINTAINERS

@@ -1626,6 +1626,18 @@ F:	drivers/clocksource/timer-atlas7.c
 N:	[^a-z]sirf
 X:	drivers/gnss
 
+ARM/CZ.NIC TURRIS MOX SUPPORT
+M:	Marek Behun <marek.behun@nic.cz>
+W:	http://mox.turris.cz
+S:	Maintained
+F:	Documentation/ABI/testing/debugfs-moxtet
+F:	Documentation/ABI/testing/sysfs-bus-moxtet-devices
+F:	Documentation/devicetree/bindings/bus/moxtet.txt
+F:	Documentation/devicetree/bindings/gpio/gpio-moxtet.txt
+F:	include/linux/moxtet.h
+F:	drivers/bus/moxtet.c
+F:	drivers/gpio/gpio-moxtet.c
+
 ARM/EBSA110 MACHINE SUPPORT
 M:	Russell King <linux@armlinux.org.uk>
 L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
@@ -15545,6 +15557,7 @@ F:	drivers/clk/clk-sc[mp]i.c
 F:	drivers/cpufreq/sc[mp]i-cpufreq.c
 F:	drivers/firmware/arm_scpi.c
 F:	drivers/firmware/arm_scmi/
+F:	drivers/reset/reset-scmi.c
 F:	include/linux/sc[mp]i_protocol.h
 
 SYSTEM RESET/SHUTDOWN DRIVERS

drivers/bus/Kconfig

@@ -29,6 +29,16 @@ config BRCMSTB_GISB_ARB
 	  arbiter. This driver provides timeout and target abort error handling
 	  and internal bus master decoding.
 
+config MOXTET
+	tristate "CZ.NIC Turris Mox module configuration bus"
+	depends on SPI_MASTER && OF
+	help
+	  Say yes here to add support for the module configuration bus found
+	  on CZ.NIC's Turris Mox. This is needed for the ability to discover
+	  the order in which the modules are connected and to get/set some of
+	  their settings. For example the GPIOs on Mox SFP module are
+	  configured through this bus.
+
 config HISILICON_LPC
 	bool "Support for ISA I/O space on HiSilicon Hip06/7"
 	depends on ARM64 && (ARCH_HISI || COMPILE_TEST)

drivers/bus/Makefile

@@ -8,6 +8,7 @@ obj-$(CONFIG_ARM_CCI)		+= arm-cci.o
 
 obj-$(CONFIG_HISILICON_LPC)	+= hisi_lpc.o
 obj-$(CONFIG_BRCMSTB_GISB_ARB)	+= brcmstb_gisb.o
+obj-$(CONFIG_MOXTET)		+= moxtet.o
 
 # DPAA2 fsl-mc bus
 obj-$(CONFIG_FSL_MC_BUS)	+= fsl-mc/

drivers/clk/clk-scmi.c

@@ -69,7 +69,7 @@ static int scmi_clk_set_rate(struct clk_hw *hw, unsigned long rate,
 {
 	struct scmi_clk *clk = to_scmi_clk(hw);
 
-	return clk->handle->clk_ops->rate_set(clk->handle, clk->id, 0, rate);
+	return clk->handle->clk_ops->rate_set(clk->handle, clk->id, rate);
 }
 
 static int scmi_clk_enable(struct clk_hw *hw)

drivers/firmware/arm_scmi/Makefile

@@ -2,5 +2,5 @@
 obj-y	= scmi-bus.o scmi-driver.o scmi-protocols.o
 scmi-bus-y = bus.o
 scmi-driver-y = driver.o
-scmi-protocols-y = base.o clock.o perf.o power.o sensors.o
+scmi-protocols-y = base.o clock.o perf.o power.o reset.o sensors.o
 obj-$(CONFIG_ARM_SCMI_POWER_DOMAIN) += scmi_pm_domain.o

drivers/firmware/arm_scmi/base.c

@@ -204,7 +204,7 @@ static int scmi_base_discover_agent_get(const struct scmi_handle *handle,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(id);
+	put_unaligned_le32(id, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret)

drivers/firmware/arm_scmi/clock.c

@@ -56,7 +56,7 @@ struct scmi_msg_resp_clock_describe_rates {
 struct scmi_clock_set_rate {
 	__le32 flags;
 #define CLOCK_SET_ASYNC		BIT(0)
-#define CLOCK_SET_DELAYED	BIT(1)
+#define CLOCK_SET_IGNORE_RESP	BIT(1)
 #define CLOCK_SET_ROUND_UP	BIT(2)
 #define CLOCK_SET_ROUND_AUTO	BIT(3)
 	__le32 id;
@@ -67,6 +67,7 @@ struct scmi_clock_set_rate {
 struct clock_info {
 	int num_clocks;
 	int max_async_req;
+	atomic_t cur_async_req;
 	struct scmi_clock_info *clk;
 };
 
@@ -106,7 +107,7 @@ static int scmi_clock_attributes_get(const struct scmi_handle *handle,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(clk_id);
+	put_unaligned_le32(clk_id, t->tx.buf);
 	attr = t->rx.buf;
 
 	ret = scmi_do_xfer(handle, t);
@@ -203,39 +204,47 @@ scmi_clock_rate_get(const struct scmi_handle *handle, u32 clk_id, u64 *value)
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(clk_id);
+	put_unaligned_le32(clk_id, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
-	if (!ret) {
-		__le32 *pval = t->rx.buf;
-
-		*value = le32_to_cpu(*pval);
-		*value |= (u64)le32_to_cpu(*(pval + 1)) << 32;
-	}
+	if (!ret)
+		*value = get_unaligned_le64(t->rx.buf);
 
 	scmi_xfer_put(handle, t);
 	return ret;
 }
 
 static int scmi_clock_rate_set(const struct scmi_handle *handle, u32 clk_id,
-			       u32 config, u64 rate)
+			       u64 rate)
 {
 	int ret;
+	u32 flags = 0;
 	struct scmi_xfer *t;
 	struct scmi_clock_set_rate *cfg;
+	struct clock_info *ci = handle->clk_priv;
 
 	ret = scmi_xfer_get_init(handle, CLOCK_RATE_SET, SCMI_PROTOCOL_CLOCK,
 				 sizeof(*cfg), 0, &t);
 	if (ret)
 		return ret;
 
+	if (ci->max_async_req &&
+	    atomic_inc_return(&ci->cur_async_req) < ci->max_async_req)
+		flags |= CLOCK_SET_ASYNC;
+
 	cfg = t->tx.buf;
-	cfg->flags = cpu_to_le32(config);
+	cfg->flags = cpu_to_le32(flags);
 	cfg->id = cpu_to_le32(clk_id);
 	cfg->value_low = cpu_to_le32(rate & 0xffffffff);
 	cfg->value_high = cpu_to_le32(rate >> 32);
 
-	ret = scmi_do_xfer(handle, t);
+	if (flags & CLOCK_SET_ASYNC)
+		ret = scmi_do_xfer_with_response(handle, t);
+	else
+		ret = scmi_do_xfer(handle, t);
+
+	if (ci->max_async_req)
+		atomic_dec(&ci->cur_async_req);
 
 	scmi_xfer_put(handle, t);
 	return ret;

drivers/firmware/arm_scmi/common.h

@@ -15,6 +15,8 @@
 #include <linux/scmi_protocol.h>
 #include <linux/types.h>
 
+#include <asm/unaligned.h>
+
 #define PROTOCOL_REV_MINOR_MASK	GENMASK(15, 0)
 #define PROTOCOL_REV_MAJOR_MASK	GENMASK(31, 16)
 #define PROTOCOL_REV_MAJOR(x)	(u16)(FIELD_GET(PROTOCOL_REV_MAJOR_MASK, (x)))
@@ -48,11 +50,11 @@ struct scmi_msg_resp_prot_version {
 /**
  * struct scmi_msg_hdr - Message(Tx/Rx) header
  *
- * @id: The identifier of the command being sent
- * @protocol_id: The identifier of the protocol used to send @id command
- * @seq: The token to identify the message. when a message/command returns,
- *	the platform returns the whole message header unmodified including
- *	the token
+ * @id: The identifier of the message being sent
+ * @protocol_id: The identifier of the protocol used to send @id message
+ * @seq: The token to identify the message. When a message returns, the
+ *	platform returns the whole message header unmodified including the
+ *	token
  * @status: Status of the transfer once it's complete
  * @poll_completion: Indicate if the transfer needs to be polled for
  *	completion or interrupt mode is used
@@ -84,17 +86,21 @@ struct scmi_msg {
  * @rx: Receive message, the buffer should be pre-allocated to store
  *	message. If request-ACK protocol is used, we can reuse the same
  *	buffer for the rx path as we use for the tx path.
- * @done: completion event
+ * @done: command message transmit completion event
+ * @async: pointer to delayed response message received event completion
  */
 struct scmi_xfer {
 	struct scmi_msg_hdr hdr;
 	struct scmi_msg tx;
 	struct scmi_msg rx;
 	struct completion done;
+	struct completion *async_done;
 };
 
 void scmi_xfer_put(const struct scmi_handle *h, struct scmi_xfer *xfer);
 int scmi_do_xfer(const struct scmi_handle *h, struct scmi_xfer *xfer);
+int scmi_do_xfer_with_response(const struct scmi_handle *h,
+			       struct scmi_xfer *xfer);
 int scmi_xfer_get_init(const struct scmi_handle *h, u8 msg_id, u8 prot_id,
 		       size_t tx_size, size_t rx_size, struct scmi_xfer **p);
 int scmi_handle_put(const struct scmi_handle *handle);

drivers/firmware/arm_scmi/power.c

@@ -96,7 +96,7 @@ scmi_power_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 	attr = t->rx.buf;
 
 	ret = scmi_do_xfer(handle, t);
@@ -147,11 +147,11 @@ scmi_power_state_get(const struct scmi_handle *handle, u32 domain, u32 *state)
 	if (ret)
 		return ret;
 
-	*(__le32 *)t->tx.buf = cpu_to_le32(domain);
+	put_unaligned_le32(domain, t->tx.buf);
 
 	ret = scmi_do_xfer(handle, t);
 	if (!ret)
-		*state = le32_to_cpu(*(__le32 *)t->rx.buf);
+		*state = get_unaligned_le32(t->rx.buf);
 
 	scmi_xfer_put(handle, t);
 	return ret;

drivers/firmware/arm_scmi/reset.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * System Control and Management Interface (SCMI) Reset Protocol
+ *
+ * Copyright (C) 2019 ARM Ltd.
+ */
+
+#include "common.h"
+
+enum scmi_reset_protocol_cmd {
+	RESET_DOMAIN_ATTRIBUTES = 0x3,
+	RESET = 0x4,
+	RESET_NOTIFY = 0x5,
+};
+
+enum scmi_reset_protocol_notify {
+	RESET_ISSUED = 0x0,
+};
+
+#define NUM_RESET_DOMAIN_MASK	0xffff
+#define RESET_NOTIFY_ENABLE	BIT(0)
+
+struct scmi_msg_resp_reset_domain_attributes {
+	__le32 attributes;
+#define SUPPORTS_ASYNC_RESET(x)		((x) & BIT(31))
+#define SUPPORTS_NOTIFY_RESET(x)	((x) & BIT(30))
+	__le32 latency;
+	    u8 name[SCMI_MAX_STR_SIZE];
+};
+
+struct scmi_msg_reset_domain_reset {
+	__le32 domain_id;
+	__le32 flags;
+#define AUTONOMOUS_RESET	BIT(0)
+#define EXPLICIT_RESET_ASSERT	BIT(1)
+#define ASYNCHRONOUS_RESET	BIT(2)
+	__le32 reset_state;
+#define ARCH_RESET_TYPE		BIT(31)
+#define COLD_RESET_STATE	BIT(0)
+#define ARCH_COLD_RESET		(ARCH_RESET_TYPE | COLD_RESET_STATE)
+};
+
+struct reset_dom_info {
+	bool async_reset;
+	bool reset_notify;
+	u32 latency_us;
+	char name[SCMI_MAX_STR_SIZE];
+};
+
+struct scmi_reset_info {
+	int num_domains;
+	struct reset_dom_info *dom_info;
+};
+
+static int scmi_reset_attributes_get(const struct scmi_handle *handle,
+				     struct scmi_reset_info *pi)
+{
+	int ret;
+	struct scmi_xfer *t;
+	u32 attr;
+
+	ret = scmi_xfer_get_init(handle, PROTOCOL_ATTRIBUTES,
+				 SCMI_PROTOCOL_RESET, 0, sizeof(attr), &t);
+	if (ret)
+		return ret;
+
+	ret = scmi_do_xfer(handle, t);
+	if (!ret) {
+		attr = get_unaligned_le32(t->rx.buf);
+		pi->num_domains = attr & NUM_RESET_DOMAIN_MASK;
+	}
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int
+scmi_reset_domain_attributes_get(const struct scmi_handle *handle, u32 domain,
+				 struct reset_dom_info *dom_info)
+{
+	int ret;
+	struct scmi_xfer *t;
+	struct scmi_msg_resp_reset_domain_attributes *attr;
+
+	ret = scmi_xfer_get_init(handle, RESET_DOMAIN_ATTRIBUTES,
+				 SCMI_PROTOCOL_RESET, sizeof(domain),
+				 sizeof(*attr), &t);
+	if (ret)
+		return ret;
+
+	put_unaligned_le32(domain, t->tx.buf);
+	attr = t->rx.buf;
+
+	ret = scmi_do_xfer(handle, t);
+	if (!ret) {
+		u32 attributes = le32_to_cpu(attr->attributes);
+
+		dom_info->async_reset = SUPPORTS_ASYNC_RESET(attributes);
+		dom_info->reset_notify = SUPPORTS_NOTIFY_RESET(attributes);
+		dom_info->latency_us = le32_to_cpu(attr->latency);
+		if (dom_info->latency_us == U32_MAX)
+			dom_info->latency_us = 0;
+		strlcpy(dom_info->name, attr->name, SCMI_MAX_STR_SIZE);
+	}
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int scmi_reset_num_domains_get(const struct scmi_handle *handle)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+
+	return pi->num_domains;
+}
+
+static char *scmi_reset_name_get(const struct scmi_handle *handle, u32 domain)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *dom = pi->dom_info + domain;
+
+	return dom->name;
+}
+
+static int scmi_reset_latency_get(const struct scmi_handle *handle, u32 domain)
+{
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *dom = pi->dom_info + domain;
+
+	return dom->latency_us;
+}
+
+static int scmi_domain_reset(const struct scmi_handle *handle, u32 domain,
+			     u32 flags, u32 state)
+{
+	int ret;
+	struct scmi_xfer *t;
+	struct scmi_msg_reset_domain_reset *dom;
+	struct scmi_reset_info *pi = handle->reset_priv;
+	struct reset_dom_info *rdom = pi->dom_info + domain;
+
+	if (rdom->async_reset)
+		flags |= ASYNCHRONOUS_RESET;
+
+	ret = scmi_xfer_get_init(handle, RESET, SCMI_PROTOCOL_RESET,
+				 sizeof(*dom), 0, &t);
+	if (ret)
+		return ret;
+
+	dom = t->tx.buf;
+	dom->domain_id = cpu_to_le32(domain);
+	dom->flags = cpu_to_le32(flags);
+	dom->domain_id = cpu_to_le32(state);
+
+	if (rdom->async_reset)
+		ret = scmi_do_xfer_with_response(handle, t);
+	else
+		ret = scmi_do_xfer(handle, t);
+
+	scmi_xfer_put(handle, t);
+	return ret;
+}
+
+static int scmi_reset_domain_reset(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, AUTONOMOUS_RESET,
+				 ARCH_COLD_RESET);
+}
+
+static int
+scmi_reset_domain_assert(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, EXPLICIT_RESET_ASSERT,
+				 ARCH_COLD_RESET);
+}
+
+static int
+scmi_reset_domain_deassert(const struct scmi_handle *handle, u32 domain)
+{
+	return scmi_domain_reset(handle, domain, 0, ARCH_COLD_RESET);
+}
+
+static struct scmi_reset_ops reset_ops = {
+	.num_domains_get = scmi_reset_num_domains_get,
+	.name_get = scmi_reset_name_get,
+	.latency_get = scmi_reset_latency_get,
+	.reset = scmi_reset_domain_reset,
+	.assert = scmi_reset_domain_assert,
+	.deassert = scmi_reset_domain_deassert,
+};
+
+static int scmi_reset_protocol_init(struct scmi_handle *handle)
+{
+	int domain;
+	u32 version;
+	struct scmi_reset_info *pinfo;
+
+	scmi_version_get(handle, SCMI_PROTOCOL_RESET, &version);
+
+	dev_dbg(handle->dev, "Reset Version %d.%d\n",
+		PROTOCOL_REV_MAJOR(version), PROTOCOL_REV_MINOR(version));
+
+	pinfo = devm_kzalloc(handle->dev, sizeof(*pinfo), GFP_KERNEL);
+	if (!pinfo)
+		return -ENOMEM;
+
+	scmi_reset_attributes_get(handle, pinfo);
+
+	pinfo->dom_info = devm_kcalloc(handle->dev, pinfo->num_domains,
+				       sizeof(*pinfo->dom_info), GFP_KERNEL);
+	if (!pinfo->dom_info)
+		return -ENOMEM;
+
+	for (domain = 0; domain < pinfo->num_domains; domain++) {
+		struct reset_dom_info *dom = pinfo->dom_info + domain;
+
+		scmi_reset_domain_attributes_get(handle, domain, dom);
+	}
+
+	handle->reset_ops = &reset_ops;
+	handle->reset_priv = pinfo;
+
+	return 0;
+}
+
+static int __init scmi_reset_init(void)
+{
+	return scmi_protocol_register(SCMI_PROTOCOL_RESET,
+				      &scmi_reset_protocol_init);
+}
+subsys_initcall(scmi_reset_init);

drivers/firmware/arm_scmi/sensors.c

@@ -9,8 +9,8 @@
 
 enum scmi_sensor_protocol_cmd {
 	SENSOR_DESCRIPTION_GET = 0x3,
-	SENSOR_CONFIG_SET = 0x4,
-	SENSOR_TRIP_POINT_SET = 0x5,
+	SENSOR_TRIP_POINT_NOTIFY = 0x4,
+	SENSOR_TRIP_POINT_CONFIG = 0x5,
 	SENSOR_READING_GET = 0x6,
 };
 
@@ -42,9 +42,10 @@ struct scmi_msg_resp_sensor_description {
 	} desc[0];
 };
 
-struct scmi_msg_set_sensor_config {
+struct scmi_msg_sensor_trip_point_notify {
 	__le32 id;
 	__le32 event_control;
+#define SENSOR_TP_NOTIFY_ALL	BIT(0)
 };
 
 struct scmi_msg_set_sensor_trip_point {
@@ -119,7 +120,7 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 
 	do {
 		/* Set the number of sensors to be skipped/already read */
-		*(__le32 *)t->tx.buf = cpu_to_le32(desc_index);
+		put_unaligned_le32(desc_index, t->tx.buf);
 
 		ret = scmi_do_xfer(handle, t);
 		if (ret)
@@ -135,9 +136,10 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 		}
 
 		for (cnt = 0; cnt < num_returned; cnt++) {
-			u32 attrh;
+			u32 attrh, attrl;
 			struct scmi_sensor_info *s;
 
+			attrl = le32_to_cpu(buf->desc[cnt].attributes_low);
 			attrh = le32_to_cpu(buf->desc[cnt].attributes_high);
 			s = &si->sensors[desc_index + cnt];
 			s->id = le32_to_cpu(buf->desc[cnt].id);
@@ -146,6 +148,8 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 			/* Sign extend to a full s8 */
 			if (s->scale & SENSOR_SCALE_SIGN)
 				s->scale |= SENSOR_SCALE_EXTEND;
+			s->async = SUPPORTS_ASYNC_READ(attrl);
+			s->num_trip_points = NUM_TRIP_POINTS(attrl);
 			strlcpy(s->name, buf->desc[cnt].name, SCMI_MAX_STR_SIZE);
 		}
 
@@ -160,15 +164,15 @@ static int scmi_sensor_description_get(const struct scmi_handle *handle,
 	return ret;
 }
 
-static int
-scmi_sensor_configuration_set(const struct scmi_handle *handle, u32 sensor_id)
+static int scmi_sensor_trip_point_notify(const struct scmi_handle *handle,
+					 u32 sensor_id, bool enable)
 {
 	int ret;
-	u32 evt_cntl = BIT(0);
+	u32 evt_cntl = enable ? SENSOR_TP_NOTIFY_ALL : 0;
 	struct scmi_xfer *t;
-	struct scmi_msg_set_sensor_config *cfg;
+	struct scmi_msg_sensor_trip_point_notify *cfg;
 
-	ret = scmi_xfer_get_init(handle, SENSOR_CONFIG_SET,
+	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_NOTIFY,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*cfg), 0, &t);
 	if (ret)
 		return ret;
@@ -183,15 +187,16 @@ scmi_sensor_configuration_set(const struct scmi_handle *handle, u32 sensor_id)
 	return ret;
 }
 
-static int scmi_sensor_trip_point_set(const struct scmi_handle *handle,
-				      u32 sensor_id, u8 trip_id, u64 trip_value)
+static int
+scmi_sensor_trip_point_config(const struct scmi_handle *handle, u32 sensor_id,
+			      u8 trip_id, u64 trip_value)
 {
 	int ret;
 	u32 evt_cntl = SENSOR_TP_BOTH;
 	struct scmi_xfer *t;
 	struct scmi_msg_set_sensor_trip_point *trip;
 
-	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_SET,
+	ret = scmi_xfer_get_init(handle, SENSOR_TRIP_POINT_CONFIG,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*trip), 0, &t);
 	if (ret)
 		return ret;
@@ -209,11 +214,13 @@ static int scmi_sensor_trip_point_set(const struct scmi_handle *handle,
 }
 
 static int scmi_sensor_reading_get(const struct scmi_handle *handle,
-				   u32 sensor_id, bool async, u64 *value)
+				   u32 sensor_id, u64 *value)
 {
 	int ret;
 	struct scmi_xfer *t;
 	struct scmi_msg_sensor_reading_get *sensor;
+	struct sensors_info *si = handle->sensor_priv;
+	struct scmi_sensor_info *s = si->sensors + sensor_id;
 
 	ret = scmi_xfer_get_init(handle, SENSOR_READING_GET,
 				 SCMI_PROTOCOL_SENSOR, sizeof(*sensor),
@@ -223,14 +230,18 @@ static int scmi_sensor_reading_get(const struct scmi_handle *handle,
 
 	sensor = t->tx.buf;
 	sensor->id = cpu_to_le32(sensor_id);
-	sensor->flags = cpu_to_le32(async ? SENSOR_READ_ASYNC : 0);
 
-	ret = scmi_do_xfer(handle, t);
-	if (!ret) {
-		__le32 *pval = t->rx.buf;
-
-		*value = le32_to_cpu(*pval);
-		*value |= (u64)le32_to_cpu(*(pval + 1)) << 32;
+	if (s->async) {
+		sensor->flags = cpu_to_le32(SENSOR_READ_ASYNC);
+		ret = scmi_do_xfer_with_response(handle, t);
+		if (!ret)
+			*value = get_unaligned_le64((void *)
+						    ((__le32 *)t->rx.buf + 1));
+	} else {
+		sensor->flags = cpu_to_le32(0);
+		ret = scmi_do_xfer(handle, t);
+		if (!ret)
+			*value = get_unaligned_le64(t->rx.buf);
 	}
 
 	scmi_xfer_put(handle, t);
@@ -255,8 +266,8 @@ static int scmi_sensor_count_get(const struct scmi_handle *handle)
 static struct scmi_sensor_ops sensor_ops = {
 	.count_get = scmi_sensor_count_get,
 	.info_get = scmi_sensor_info_get,
-	.configuration_set = scmi_sensor_configuration_set,
-	.trip_point_set = scmi_sensor_trip_point_set,
+	.trip_point_notify = scmi_sensor_trip_point_notify,
+	.trip_point_config = scmi_sensor_trip_point_config,
 	.reading_get = scmi_sensor_reading_get,
 };
 

drivers/gpio/Kconfig

@@ -1445,6 +1445,15 @@ config GPIO_XRA1403
 	help
 	  GPIO driver for EXAR XRA1403 16-bit SPI-based GPIO expander.
 
+config GPIO_MOXTET
+	tristate "Turris Mox Moxtet bus GPIO expander"
+	depends on MOXTET
+	help
+	  Say yes here if you are building for the Turris Mox router.
+	  This is the driver needed for configuring the GPIOs via the Moxtet
+	  bus. For example the Mox module with SFP cage needs this driver
+	  so that phylink can use corresponding GPIOs.
+
 endmenu
 
 menu "USB GPIO expanders"

drivers/gpio/Makefile

@@ -93,6 +93,7 @@ obj-$(CONFIG_GPIO_ML_IOH)		+= gpio-ml-ioh.o
 obj-$(CONFIG_GPIO_MLXBF)		+= gpio-mlxbf.o
 obj-$(CONFIG_GPIO_MM_LANTIQ)		+= gpio-mm-lantiq.o
 obj-$(CONFIG_GPIO_MOCKUP)		+= gpio-mockup.o
+obj-$(CONFIG_GPIO_MOXTET)		+= gpio-moxtet.o
 obj-$(CONFIG_GPIO_MPC5200)		+= gpio-mpc5200.o
 obj-$(CONFIG_GPIO_MPC8XXX)		+= gpio-mpc8xxx.o
 obj-$(CONFIG_GPIO_MSIC)			+= gpio-msic.o

drivers/gpio/gpio-moxtet.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ *  Turris Mox Moxtet GPIO expander
+ *
+ *  Copyright (C) 2018 Marek Behun <marek.behun@nic.cz>
+ */
+
+#include <linux/bitops.h>
+#include <linux/gpio/driver.h>
+#include <linux/moxtet.h>
+#include <linux/module.h>
+
+#define MOXTET_GPIO_NGPIOS	12
+#define MOXTET_GPIO_INPUTS	4
+
+struct moxtet_gpio_desc {
+	u16 in_mask;
+	u16 out_mask;
+};
+
+static const struct moxtet_gpio_desc descs[] = {
+	[TURRIS_MOX_MODULE_SFP] = {
+		.in_mask = GENMASK(2, 0),
+		.out_mask = GENMASK(5, 4),
+	},
+};
+
+struct moxtet_gpio_chip {
+	struct device			*dev;
+	struct gpio_chip		gpio_chip;
+	const struct moxtet_gpio_desc	*desc;
+};
+
+static int moxtet_gpio_get_value(struct gpio_chip *gc, unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+	int ret;
+
+	if (chip->desc->in_mask & BIT(offset)) {
+		ret = moxtet_device_read(chip->dev);
+	} else if (chip->desc->out_mask & BIT(offset)) {
+		ret = moxtet_device_written(chip->dev);
+		if (ret >= 0)
+			ret <<= MOXTET_GPIO_INPUTS;
+	} else {
+		return -EINVAL;
+	}
+
+	if (ret < 0)
+		return ret;
+
+	return !!(ret & BIT(offset));
+}
+
+static void moxtet_gpio_set_value(struct gpio_chip *gc, unsigned int offset,
+				  int val)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+	int state;
+
+	state = moxtet_device_written(chip->dev);
+	if (state < 0)
+		return;
+
+	offset -= MOXTET_GPIO_INPUTS;
+
+	if (val)
+		state |= BIT(offset);
+	else
+		state &= ~BIT(offset);
+
+	moxtet_device_write(chip->dev, state);
+}
+
+static int moxtet_gpio_get_direction(struct gpio_chip *gc, unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	/* All lines are hard wired to be either input or output, not both. */
+	if (chip->desc->in_mask & BIT(offset))
+		return 1;
+	else if (chip->desc->out_mask & BIT(offset))
+		return 0;
+	else
+		return -EINVAL;
+}
+
+static int moxtet_gpio_direction_input(struct gpio_chip *gc,
+				       unsigned int offset)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	if (chip->desc->in_mask & BIT(offset))
+		return 0;
+	else if (chip->desc->out_mask & BIT(offset))
+		return -ENOTSUPP;
+	else
+		return -EINVAL;
+}
+
+static int moxtet_gpio_direction_output(struct gpio_chip *gc,
+					unsigned int offset, int val)
+{
+	struct moxtet_gpio_chip *chip = gpiochip_get_data(gc);
+
+	if (chip->desc->out_mask & BIT(offset))
+		moxtet_gpio_set_value(gc, offset, val);
+	else if (chip->desc->in_mask & BIT(offset))
+		return -ENOTSUPP;
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static int moxtet_gpio_probe(struct device *dev)
+{
+	struct moxtet_gpio_chip *chip;
+	struct device_node *nc = dev->of_node;
+	int id;
+
+	id = to_moxtet_device(dev)->id;
+
+	if (id >= ARRAY_SIZE(descs)) {
+		dev_err(dev, "%pOF Moxtet device id 0x%x is not supported by gpio-moxtet driver\n",
+			nc, id);
+		return -ENOTSUPP;
+	}
+
+	chip = devm_kzalloc(dev, sizeof(*chip), GFP_KERNEL);
+	if (!chip)
+		return -ENOMEM;
+
+	chip->dev = dev;
+	chip->gpio_chip.parent = dev;
+	chip->desc = &descs[id];
+
+	dev_set_drvdata(dev, chip);
+
+	chip->gpio_chip.label = dev_name(dev);
+	chip->gpio_chip.get_direction = moxtet_gpio_get_direction;
+	chip->gpio_chip.direction_input = moxtet_gpio_direction_input;
+	chip->gpio_chip.direction_output = moxtet_gpio_direction_output;
+	chip->gpio_chip.get = moxtet_gpio_get_value;
+	chip->gpio_chip.set = moxtet_gpio_set_value;
+	chip->gpio_chip.base = -1;
+
+	chip->gpio_chip.ngpio = MOXTET_GPIO_NGPIOS;
+
+	chip->gpio_chip.can_sleep = true;
+	chip->gpio_chip.owner = THIS_MODULE;
+
+	return devm_gpiochip_add_data(dev, &chip->gpio_chip, chip);
+}
+
+static const struct of_device_id moxtet_gpio_dt_ids[] = {
+	{ .compatible = "cznic,moxtet-gpio", },
+	{},
+};
+MODULE_DEVICE_TABLE(of, moxtet_gpio_dt_ids);
+
+static const enum turris_mox_module_id moxtet_gpio_module_table[] = {
+	TURRIS_MOX_MODULE_SFP,
+	0,
+};
+
+static struct moxtet_driver moxtet_gpio_driver = {
+	.driver = {
+		.name		= "moxtet-gpio",
+		.of_match_table	= moxtet_gpio_dt_ids,
+		.probe		= moxtet_gpio_probe,
+	},
+	.id_table = moxtet_gpio_module_table,
+};
+module_moxtet_driver(moxtet_gpio_driver);
+
+MODULE_AUTHOR("Marek Behun <marek.behun@nic.cz>");
+MODULE_DESCRIPTION("Turris Mox Moxtet GPIO expander");
+MODULE_LICENSE("GPL v2");

drivers/hwmon/scmi-hwmon.c

@@ -72,7 +72,7 @@ static int scmi_hwmon_read(struct device *dev, enum hwmon_sensor_types type,
 	const struct scmi_handle *h = scmi_sensors->handle;
 
 	sensor = *(scmi_sensors->info[type] + channel);
-	ret = h->sensor_ops->reading_get(h, sensor->id, false, &value);
+	ret = h->sensor_ops->reading_get(h, sensor->id, &value);
 	if (ret)
 		return ret;
 

drivers/reset/Kconfig

@@ -116,9 +116,20 @@ config RESET_QCOM_PDC
 	  to control reset signals provided by PDC for Modem, Compute,
 	  Display, GPU, Debug, AOP, Sensors, Audio, SP and APPS.
 
+config RESET_SCMI
+	tristate "Reset driver controlled via ARM SCMI interface"
+	depends on ARM_SCMI_PROTOCOL || COMPILE_TEST
+	default ARM_SCMI_PROTOCOL
+	help
+	  This driver provides support for reset signal/domains that are
+	  controlled by firmware that implements the SCMI interface.
+
+	  This driver uses SCMI Message Protocol to interact with the
+	  firmware controlling all the reset signals.
+
 config RESET_SIMPLE
 	bool "Simple Reset Controller Driver" if COMPILE_TEST
-	default ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED || ARCH_BITMAIN
+	default ARCH_STM32 || ARCH_STRATIX10 || ARCH_SUNXI || ARCH_ZX || ARCH_ASPEED || ARCH_BITMAIN || ARC
 	help
 	  This enables a simple reset controller driver for reset lines that
 	  that can be asserted and deasserted by toggling bits in a contiguous,

drivers/reset/Makefile

@@ -18,6 +18,7 @@ obj-$(CONFIG_RESET_OXNAS) += reset-oxnas.o
 obj-$(CONFIG_RESET_PISTACHIO) += reset-pistachio.o
 obj-$(CONFIG_RESET_QCOM_AOSS) += reset-qcom-aoss.o
 obj-$(CONFIG_RESET_QCOM_PDC) += reset-qcom-pdc.o
+obj-$(CONFIG_RESET_SCMI) += reset-scmi.o
 obj-$(CONFIG_RESET_SIMPLE) += reset-simple.o
 obj-$(CONFIG_RESET_STM32MP157) += reset-stm32mp1.o
 obj-$(CONFIG_RESET_SOCFPGA) += reset-socfpga.o

drivers/reset/reset-imx7.c

@@ -169,9 +169,9 @@ static const struct imx7_src_signal imx8mq_src_signals[IMX8MQ_RESET_NUM] = {
 	[IMX8MQ_RESET_OTG2_PHY_RESET]		= { SRC_USBOPHY2_RCR, BIT(0) },
 	[IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N]	= { SRC_MIPIPHY_RCR, BIT(1) },
 	[IMX8MQ_RESET_MIPI_DSI_RESET_N]		= { SRC_MIPIPHY_RCR, BIT(2) },
-	[IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(3) },
-	[IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(4) },
-	[IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(5) },
+	[IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(3) },
+	[IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(4) },
+	[IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N]	= { SRC_MIPIPHY_RCR, BIT(5) },
 	[IMX8MQ_RESET_PCIEPHY]			= { SRC_PCIEPHY_RCR,
 						    BIT(2) | BIT(1) },
 	[IMX8MQ_RESET_PCIEPHY_PERST]		= { SRC_PCIEPHY_RCR, BIT(3) },
@@ -220,9 +220,9 @@ static int imx8mq_reset_set(struct reset_controller_dev *rcdev,
 
 	case IMX8MQ_RESET_PCIE_CTRL_APPS_EN:
 	case IMX8MQ_RESET_PCIE2_CTRL_APPS_EN:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N:	/* fallthrough */
-	case IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N:	/* fallthrough */
+	case IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N:	/* fallthrough */
 	case IMX8MQ_RESET_MIPI_DSI_RESET_N:	/* fallthrough */
 	case IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N:	/* fallthrough */
 		value = assert ? 0 : bit;

drivers/reset/reset-meson.c

+// SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause
 /*
  * Amlogic Meson Reset Controller driver
  *
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #include <linux/err.h>
 #include <linux/init.h>

drivers/reset/reset-scmi.c

+// SPDX-License-Identifier: GPL-2.0
+/*
+ * ARM System Control and Management Interface (ARM SCMI) reset driver
+ *
+ * Copyright (C) 2019 ARM Ltd.
+ */
+
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/device.h>
+#include <linux/reset-controller.h>
+#include <linux/scmi_protocol.h>
+
+/**
+ * struct scmi_reset_data - reset controller information structure
+ * @rcdev: reset controller entity
+ * @handle: ARM SCMI handle used for communication with system controller
+ */
+struct scmi_reset_data {
+	struct reset_controller_dev rcdev;
+	const struct scmi_handle *handle;
+};
+
+#define to_scmi_reset_data(p)	container_of((p), struct scmi_reset_data, rcdev)
+#define to_scmi_handle(p)	(to_scmi_reset_data(p)->handle)
+
+/**
+ * scmi_reset_assert() - assert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of the reset to be asserted
+ *
+ * This function implements the reset driver op to assert a device's reset
+ * using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_assert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->assert(handle, id);
+}
+
+/**
+ * scmi_reset_deassert() - deassert device reset
+ * @rcdev: reset controller entity
+ * @id: ID of the reset to be deasserted
+ *
+ * This function implements the reset driver op to deassert a device's reset
+ * using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_deassert(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->deassert(handle, id);
+}
+
+/**
+ * scmi_reset_reset() - reset the device
+ * @rcdev: reset controller entity
+ * @id: ID of the reset signal to be reset(assert + deassert)
+ *
+ * This function implements the reset driver op to trigger a device's
+ * reset signal using the ARM SCMI protocol.
+ *
+ * Return: 0 for successful request, else a corresponding error value
+ */
+static int
+scmi_reset_reset(struct reset_controller_dev *rcdev, unsigned long id)
+{
+	const struct scmi_handle *handle = to_scmi_handle(rcdev);
+
+	return handle->reset_ops->reset(handle, id);
+}
+
+static const struct reset_control_ops scmi_reset_ops = {
+	.assert		= scmi_reset_assert,
+	.deassert	= scmi_reset_deassert,
+	.reset		= scmi_reset_reset,
+};
+
+static int scmi_reset_probe(struct scmi_device *sdev)
+{
+	struct scmi_reset_data *data;
+	struct device *dev = &sdev->dev;
+	struct device_node *np = dev->of_node;
+	const struct scmi_handle *handle = sdev->handle;
+
+	if (!handle || !handle->reset_ops)
+		return -ENODEV;
+
+	data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL);
+	if (!data)
+		return -ENOMEM;
+
+	data->rcdev.ops = &scmi_reset_ops;
+	data->rcdev.owner = THIS_MODULE;
+	data->rcdev.of_node = np;
+	data->rcdev.nr_resets = handle->reset_ops->num_domains_get(handle);
+
+	return devm_reset_controller_register(dev, &data->rcdev);
+}
+
+static const struct scmi_device_id scmi_id_table[] = {
+	{ SCMI_PROTOCOL_RESET },
+	{ },
+};
+MODULE_DEVICE_TABLE(scmi, scmi_id_table);
+
+static struct scmi_driver scmi_reset_driver = {
+	.name = "scmi-reset",
+	.probe = scmi_reset_probe,
+	.id_table = scmi_id_table,
+};
+module_scmi_driver(scmi_reset_driver);
+
+MODULE_AUTHOR("Sudeep Holla <sudeep.holla@arm.com>");
+MODULE_DESCRIPTION("ARM SCMI reset controller driver");
+MODULE_LICENSE("GPL v2");

drivers/reset/reset-simple.c

@@ -127,6 +127,9 @@ static const struct of_device_id reset_simple_dt_ids[] = {
 	{ .compatible = "aspeed,ast2500-lpc-reset" },
 	{ .compatible = "bitmain,bm1880-reset",
 		.data = &reset_simple_active_low },
+	{ .compatible = "snps,dw-high-reset" },
+	{ .compatible = "snps,dw-low-reset",
+		.data = &reset_simple_active_low },
 	{ /* sentinel */ },
 };
 

drivers/soc/fsl/dpaa2-console.c

@@ -73,7 +73,7 @@ static u64 get_mc_fw_base_address(void)
 
 	mcfbaregs = ioremap(mc_base_addr.start, resource_size(&mc_base_addr));
 	if (!mcfbaregs) {
-		pr_err("could not map MC Firmaware Base registers\n");
+		pr_err("could not map MC Firmware Base registers\n");
 		return 0;
 	}
 

drivers/soc/fsl/qe/qe.c

@@ -10,6 +10,7 @@
  * General Purpose functions for the global management of the
  * QUICC Engine (QE).
  */
+#include <linux/bitmap.h>
 #include <linux/errno.h>
 #include <linux/sched.h>
 #include <linux/kernel.h>
@@ -39,29 +40,32 @@ static DEFINE_SPINLOCK(qe_lock);
 DEFINE_SPINLOCK(cmxgcr_lock);
 EXPORT_SYMBOL(cmxgcr_lock);
 
-/* QE snum state */
-enum qe_snum_state {
-	QE_SNUM_STATE_USED,
-	QE_SNUM_STATE_FREE
-};
-
-/* QE snum */
-struct qe_snum {
-	u8 num;
-	enum qe_snum_state state;
-};
-
 /* We allocate this here because it is used almost exclusively for
  * the communication processor devices.
  */
 struct qe_immap __iomem *qe_immr;
 EXPORT_SYMBOL(qe_immr);
 
-static struct qe_snum snums[QE_NUM_OF_SNUM];	/* Dynamically allocated SNUMs */
+static u8 snums[QE_NUM_OF_SNUM];	/* Dynamically allocated SNUMs */
+static DECLARE_BITMAP(snum_state, QE_NUM_OF_SNUM);
 static unsigned int qe_num_of_snum;
 
 static phys_addr_t qebase = -1;
 
+static struct device_node *qe_get_device_node(void)
+{
+	struct device_node *qe;
+
+	/*
+	 * Newer device trees have an "fsl,qe" compatible property for the QE
+	 * node, but we still need to support older device trees.
+	 */
+	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
+	if (qe)
+		return qe;
+	return of_find_node_by_type(NULL, "qe");
+}
+
 static phys_addr_t get_qe_base(void)
 {
 	struct device_node *qe;
@@ -71,12 +75,9 @@ static phys_addr_t get_qe_base(void)
 	if (qebase != -1)
 		return qebase;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return qebase;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return qebase;
 
 	ret = of_address_to_resource(qe, 0, &res);
 	if (!ret)
@@ -170,12 +171,9 @@ unsigned int qe_get_brg_clk(void)
 	if (brg_clk)
 		return brg_clk;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return brg_clk;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return brg_clk;
 
 	prop = of_get_property(qe, "brg-frequency", &size);
 	if (prop && size == sizeof(*prop))
@@ -281,7 +279,6 @@ EXPORT_SYMBOL(qe_clock_source);
  */
 static void qe_snums_init(void)
 {
-	int i;
 	static const u8 snum_init_76[] = {
 		0x04, 0x05, 0x0C, 0x0D, 0x14, 0x15, 0x1C, 0x1D,
 		0x24, 0x25, 0x2C, 0x2D, 0x34, 0x35, 0x88, 0x89,
@@ -302,19 +299,39 @@ static void qe_snums_init(void)
 		0x28, 0x29, 0x38, 0x39, 0x48, 0x49, 0x58, 0x59,
 		0x68, 0x69, 0x78, 0x79, 0x80, 0x81,
 	};
-	static const u8 *snum_init;
+	struct device_node *qe;
+	const u8 *snum_init;
+	int i;
 
-	qe_num_of_snum = qe_get_num_of_snums();
+	bitmap_zero(snum_state, QE_NUM_OF_SNUM);
+	qe_num_of_snum = 28; /* The default number of snum for threads is 28 */
+	qe = qe_get_device_node();
+	if (qe) {
+		i = of_property_read_variable_u8_array(qe, "fsl,qe-snums",
+						       snums, 1, QE_NUM_OF_SNUM);
+		if (i > 0) {
+			of_node_put(qe);
+			qe_num_of_snum = i;
+			return;
+		}
+		/*
+		 * Fall back to legacy binding of using the value of
+		 * fsl,qe-num-snums to choose one of the static arrays
+		 * above.
+		 */
+		of_property_read_u32(qe, "fsl,qe-num-snums", &qe_num_of_snum);
+		of_node_put(qe);
+	}
 
-	if (qe_num_of_snum == 76)
+	if (qe_num_of_snum == 76) {
 		snum_init = snum_init_76;
-	else
+	} else if (qe_num_of_snum == 28 || qe_num_of_snum == 46) {
 		snum_init = snum_init_46;
-
-	for (i = 0; i < qe_num_of_snum; i++) {
-		snums[i].num = snum_init[i];
-		snums[i].state = QE_SNUM_STATE_FREE;
+	} else {
+		pr_err("QE: unsupported value of fsl,qe-num-snums: %u\n", qe_num_of_snum);
+		return;
 	}
+	memcpy(snums, snum_init, qe_num_of_snum);
 }
 
 int qe_get_snum(void)
@@ -324,12 +341,10 @@ int qe_get_snum(void)
 	int i;
 
 	spin_lock_irqsave(&qe_lock, flags);
-	for (i = 0; i < qe_num_of_snum; i++) {
-		if (snums[i].state == QE_SNUM_STATE_FREE) {
-			snums[i].state = QE_SNUM_STATE_USED;
-			snum = snums[i].num;
-			break;
-		}
+	i = find_first_zero_bit(snum_state, qe_num_of_snum);
+	if (i < qe_num_of_snum) {
+		set_bit(i, snum_state);
+		snum = snums[i];
 	}
 	spin_unlock_irqrestore(&qe_lock, flags);
 
@@ -339,14 +354,10 @@ EXPORT_SYMBOL(qe_get_snum);
 
 void qe_put_snum(u8 snum)
 {
-	int i;
+	const u8 *p = memchr(snums, snum, qe_num_of_snum);
 
-	for (i = 0; i < qe_num_of_snum; i++) {
-		if (snums[i].num == snum) {
-			snums[i].state = QE_SNUM_STATE_FREE;
-			break;
-		}
-	}
+	if (p)
+		clear_bit(p - snums, snum_state);
 }
 EXPORT_SYMBOL(qe_put_snum);
 
@@ -572,16 +583,9 @@ struct qe_firmware_info *qe_get_firmware_info(void)
 
 	initialized = 1;
 
-	/*
-	 * Newer device trees have an "fsl,qe" compatible property for the QE
-	 * node, but we still need to support older device trees.
-	*/
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return NULL;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return NULL;
 
 	/* Find the 'firmware' child node */
 	fw = of_get_child_by_name(qe, "firmware");
@@ -627,16 +631,9 @@ unsigned int qe_get_num_of_risc(void)
 	unsigned int num_of_risc = 0;
 	const u32 *prop;
 
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		/* Older devices trees did not have an "fsl,qe"
-		 * compatible property, so we need to look for
-		 * the QE node by name.
-		 */
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return num_of_risc;
-	}
+	qe = qe_get_device_node();
+	if (!qe)
+		return num_of_risc;
 
 	prop = of_get_property(qe, "fsl,qe-num-riscs", &size);
 	if (prop && size == sizeof(*prop))
@@ -650,37 +647,7 @@ EXPORT_SYMBOL(qe_get_num_of_risc);
 
 unsigned int qe_get_num_of_snums(void)
 {
-	struct device_node *qe;
-	int size;
-	unsigned int num_of_snums;
-	const u32 *prop;
-
-	num_of_snums = 28; /* The default number of snum for threads is 28 */
-	qe = of_find_compatible_node(NULL, NULL, "fsl,qe");
-	if (!qe) {
-		/* Older devices trees did not have an "fsl,qe"
-		 * compatible property, so we need to look for
-		 * the QE node by name.
-		 */
-		qe = of_find_node_by_type(NULL, "qe");
-		if (!qe)
-			return num_of_snums;
-	}
-
-	prop = of_get_property(qe, "fsl,qe-num-snums", &size);
-	if (prop && size == sizeof(*prop)) {
-		num_of_snums = *prop;
-		if ((num_of_snums < 28) || (num_of_snums > QE_NUM_OF_SNUM)) {
-			/* No QE ever has fewer than 28 SNUMs */
-			pr_err("QE: number of snum is invalid\n");
-			of_node_put(qe);
-			return -EINVAL;
-		}
-	}
-
-	of_node_put(qe);
-
-	return num_of_snums;
+	return qe_num_of_snum;
 }
 EXPORT_SYMBOL(qe_get_num_of_snums);
 

drivers/soc/renesas/rcar-sysc.c

@@ -170,7 +170,7 @@ struct rcar_sysc_pd {
 	struct generic_pm_domain genpd;
 	struct rcar_sysc_ch ch;
 	unsigned int flags;
-	char name[0];
+	char name[];
 };
 
 static inline struct rcar_sysc_pd *to_rcar_pd(struct generic_pm_domain *d)

drivers/tee/optee/call.c

@@ -148,6 +148,7 @@ u32 optee_do_call_with_arg(struct tee_context *ctx, phys_addr_t parg)
 			 */
 			optee_cq_wait_for_completion(&optee->call_queue, &w);
 		} else if (OPTEE_SMC_RETURN_IS_RPC(res.a0)) {
+			might_sleep();
 			param.a0 = res.a0;
 			param.a1 = res.a1;
 			param.a2 = res.a2;

include/dt-bindings/bus/moxtet.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Constant for device tree bindings for Turris Mox module configuration bus
+ *
+ * Copyright (C) 2019 Marek Behun <marek.behun@nic.cz>
+ */
+
+#ifndef _DT_BINDINGS_BUS_MOXTET_H
+#define _DT_BINDINGS_BUS_MOXTET_H
+
+#define MOXTET_IRQ_PCI		0
+#define MOXTET_IRQ_USB3		4
+#define MOXTET_IRQ_PERIDOT(n)	(8 + (n))
+#define MOXTET_IRQ_TOPAZ	12
+
+#endif /* _DT_BINDINGS_BUS_MOXTET_H */

include/dt-bindings/reset/amlogic,meson-gxbb-reset.h

+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #ifndef _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H
 #define _DT_BINDINGS_AMLOGIC_MESON_GXBB_RESET_H

include/dt-bindings/reset/amlogic,meson8b-reset.h

+/* SPDX-License-Identifier: GPL-2.0 OR BSD-3-Clause */
 /*
- * This file is provided under a dual BSD/GPLv2 license.  When using or
- * redistributing this file, you may do so under either license.
- *
- * GPL LICENSE SUMMARY
- *
  * Copyright (c) 2016 BayLibre, SAS.
  * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * This program is free software; you can redistribute it and/or modify
- * it under the terms of version 2 of the GNU General Public License as
- * published by the Free Software Foundation.
- *
- * This program is distributed in the hope that it will be useful, but
- * WITHOUT ANY WARRANTY; without even the implied warranty of
- * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the GNU
- * General Public License for more details.
- *
- * You should have received a copy of the GNU General Public License
- * along with this program; if not, see <http://www.gnu.org/licenses/>.
- * The full GNU General Public License is included in this distribution
- * in the file called COPYING.
- *
- * BSD LICENSE
- *
- * Copyright (c) 2016 BayLibre, SAS.
- * Author: Neil Armstrong <narmstrong@baylibre.com>
- *
- * Redistribution and use in source and binary forms, with or without
- * modification, are permitted provided that the following conditions
- * are met:
- *
- *   * Redistributions of source code must retain the above copyright
- *     notice, this list of conditions and the following disclaimer.
- *   * Redistributions in binary form must reproduce the above copyright
- *     notice, this list of conditions and the following disclaimer in
- *     the documentation and/or other materials provided with the
- *     distribution.
- *   * Neither the name of Intel Corporation nor the names of its
- *     contributors may be used to endorse or promote products derived
- *     from this software without specific prior written permission.
- *
- * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
- * "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
- * LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
- * A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
- * OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
- * SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
- * LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
- * DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
- * THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
- * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
- * OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
  */
 #ifndef _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H
 #define _DT_BINDINGS_AMLOGIC_MESON8B_RESET_H

include/dt-bindings/reset/imx8mq-reset.h

@@ -31,33 +31,33 @@
 #define IMX8MQ_RESET_OTG2_PHY_RESET		20
 #define IMX8MQ_RESET_MIPI_DSI_RESET_BYTE_N	21
 #define IMX8MQ_RESET_MIPI_DSI_RESET_N		22
-#define IMX8MQ_RESET_MIPI_DIS_DPI_RESET_N	23
-#define IMX8MQ_RESET_MIPI_DIS_ESC_RESET_N	24
-#define IMX8MQ_RESET_MIPI_DIS_PCLK_RESET_N	25
+#define IMX8MQ_RESET_MIPI_DSI_DPI_RESET_N	23
+#define IMX8MQ_RESET_MIPI_DSI_ESC_RESET_N	24
+#define IMX8MQ_RESET_MIPI_DSI_PCLK_RESET_N	25
 #define IMX8MQ_RESET_PCIEPHY			26
 #define IMX8MQ_RESET_PCIEPHY_PERST		27
 #define IMX8MQ_RESET_PCIE_CTRL_APPS_EN		28
 #define IMX8MQ_RESET_PCIE_CTRL_APPS_TURNOFF	29
-#define IMX8MQ_RESET_HDMI_PHY_APB_RESET		30
+#define IMX8MQ_RESET_HDMI_PHY_APB_RESET		30	/* i.MX8MM does NOT support */
 #define IMX8MQ_RESET_DISP_RESET			31
 #define IMX8MQ_RESET_GPU_RESET			32
 #define IMX8MQ_RESET_VPU_RESET			33
-#define IMX8MQ_RESET_PCIEPHY2			34
-#define IMX8MQ_RESET_PCIEPHY2_PERST		35
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN		36
-#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF	37
-#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38
-#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET	39
-#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET	40
-#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET	41
-#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET	42
-#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET	43
+#define IMX8MQ_RESET_PCIEPHY2			34	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIEPHY2_PERST		35	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_EN		36	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_PCIE2_CTRL_APPS_TURNOFF	37	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_CORE_RESET	38	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_PHY_REF_RESET	39	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI1_ESC_RESET	40	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_CORE_RESET	41	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_PHY_REF_RESET	42	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_MIPI_CSI2_ESC_RESET	43	/* i.MX8MM does NOT support */
 #define IMX8MQ_RESET_DDRC1_PRST			44
 #define IMX8MQ_RESET_DDRC1_CORE_RESET		45
 #define IMX8MQ_RESET_DDRC1_PHY_RESET		46
-#define IMX8MQ_RESET_DDRC2_PRST			47
-#define IMX8MQ_RESET_DDRC2_CORE_RESET		48
-#define IMX8MQ_RESET_DDRC2_PHY_RESET		49
+#define IMX8MQ_RESET_DDRC2_PRST			47	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_DDRC2_CORE_RESET		48	/* i.MX8MM does NOT support */
+#define IMX8MQ_RESET_DDRC2_PHY_RESET		49	/* i.MX8MM does NOT support */
 
 #define IMX8MQ_RESET_NUM			50
 

include/linux/moxtet.h

+/* SPDX-License-Identifier: GPL-2.0 */
+/*
+ * Turris Mox module configuration bus driver
+ *
+ * Copyright (C) 2019 Marek Behun <marek.behun@nic.cz>
+ */
+
+#ifndef __LINUX_MOXTET_H
+#define __LINUX_MOXTET_H
+
+#include <linux/device.h>
+#include <linux/irq.h>
+#include <linux/irqdomain.h>
+#include <linux/mutex.h>
+
+#define TURRIS_MOX_MAX_MODULES	10
+
+enum turris_mox_cpu_module_id {
+	TURRIS_MOX_CPU_ID_EMMC	= 0x00,
+	TURRIS_MOX_CPU_ID_SD	= 0x10,
+};
+
+enum turris_mox_module_id {
+	TURRIS_MOX_MODULE_FIRST		= 0x01,
+
+	TURRIS_MOX_MODULE_SFP		= 0x01,
+	TURRIS_MOX_MODULE_PCI		= 0x02,
+	TURRIS_MOX_MODULE_TOPAZ		= 0x03,
+	TURRIS_MOX_MODULE_PERIDOT	= 0x04,
+	TURRIS_MOX_MODULE_USB3		= 0x05,
+	TURRIS_MOX_MODULE_PCI_BRIDGE	= 0x06,
+
+	TURRIS_MOX_MODULE_LAST		= 0x06,
+};
+
+#define MOXTET_NIRQS	16
+
+extern struct bus_type moxtet_type;
+
+struct moxtet {
+	struct device			*dev;
+	struct mutex			lock;
+	u8				modules[TURRIS_MOX_MAX_MODULES];
+	int				count;
+	u8				tx[TURRIS_MOX_MAX_MODULES];
+	int				dev_irq;
+	struct {
+		struct irq_domain	*domain;
+		struct irq_chip		chip;
+		unsigned long		masked, exists;
+		struct moxtet_irqpos {
+					u8 idx;
+					u8 bit;
+		} position[MOXTET_NIRQS];
+	} irq;
+#ifdef CONFIG_DEBUG_FS
+	struct dentry			*debugfs_root;
+#endif
+};
+
+struct moxtet_driver {
+	const enum turris_mox_module_id	*id_table;
+	struct device_driver		driver;
+};
+
+static inline struct moxtet_driver *
+to_moxtet_driver(struct device_driver *drv)
+{
+	if (!drv)
+		return NULL;
+	return container_of(drv, struct moxtet_driver, driver);
+}
+
+extern int __moxtet_register_driver(struct module *owner,
+				    struct moxtet_driver *mdrv);
+
+static inline void moxtet_unregister_driver(struct moxtet_driver *mdrv)
+{
+	if (mdrv)
+		driver_unregister(&mdrv->driver);
+}
+
+#define moxtet_register_driver(driver) \
+	__moxtet_register_driver(THIS_MODULE, driver)
+
+#define module_moxtet_driver(__moxtet_driver) \
+	module_driver(__moxtet_driver, moxtet_register_driver, \
+			moxtet_unregister_driver)
+
+struct moxtet_device {
+	struct device			dev;
+	struct moxtet			*moxtet;
+	enum turris_mox_module_id	id;
+	unsigned int			idx;
+};
+
+extern int moxtet_device_read(struct device *dev);
+extern int moxtet_device_write(struct device *dev, u8 val);
+extern int moxtet_device_written(struct device *dev);
+
+static inline struct moxtet_device *
+to_moxtet_device(struct device *dev)
+{
+	if (!dev)
+		return NULL;
+	return container_of(dev, struct moxtet_device, dev);
+}
+
+#endif /* __LINUX_MOXTET_H */

include/linux/scmi_protocol.h

-// SPDX-License-Identifier: GPL-2.0
+/* SPDX-License-Identifier: GPL-2.0-only */
 /*
  * SCMI Message Protocol driver header
  *
@@ -71,7 +71,7 @@ struct scmi_clk_ops {
 	int (*rate_get)(const struct scmi_handle *handle, u32 clk_id,
 			u64 *rate);
 	int (*rate_set)(const struct scmi_handle *handle, u32 clk_id,
-			u32 config, u64 rate);
+			u64 rate);
 	int (*enable)(const struct scmi_handle *handle, u32 clk_id);
 	int (*disable)(const struct scmi_handle *handle, u32 clk_id);
 };
@@ -145,6 +145,8 @@ struct scmi_sensor_info {
 	u32 id;
 	u8 type;
 	s8 scale;
+	u8 num_trip_points;
+	bool async;
 	char name[SCMI_MAX_STR_SIZE];
 };
 
@@ -167,9 +169,9 @@ enum scmi_sensor_class {
  *
  * @count_get: get the count of sensors provided by SCMI
  * @info_get: get the information of the specified sensor
- * @configuration_set: control notifications on cross-over events for
+ * @trip_point_notify: control notifications on cross-over events for
  *	the trip-points
- * @trip_point_set: selects and configures a trip-point of interest
+ * @trip_point_config: selects and configures a trip-point of interest
  * @reading_get: gets the current value of the sensor
  */
 struct scmi_sensor_ops {
@@ -177,12 +179,32 @@ struct scmi_sensor_ops {
 
 	const struct scmi_sensor_info *(*info_get)
 		(const struct scmi_handle *handle, u32 sensor_id);
-	int (*configuration_set)(const struct scmi_handle *handle,
-				 u32 sensor_id);
-	int (*trip_point_set)(const struct scmi_handle *handle, u32 sensor_id,
-			      u8 trip_id, u64 trip_value);
+	int (*trip_point_notify)(const struct scmi_handle *handle,
+				 u32 sensor_id, bool enable);
+	int (*trip_point_config)(const struct scmi_handle *handle,
+				 u32 sensor_id, u8 trip_id, u64 trip_value);
 	int (*reading_get)(const struct scmi_handle *handle, u32 sensor_id,
-			   bool async, u64 *value);
+			   u64 *value);
+};
+
+/**
+ * struct scmi_reset_ops - represents the various operations provided
+ *	by SCMI Reset Protocol
+ *
+ * @num_domains_get: get the count of reset domains provided by SCMI
+ * @name_get: gets the name of a reset domain
+ * @latency_get: gets the reset latency for the specified reset domain
+ * @reset: resets the specified reset domain
+ * @assert: explicitly assert reset signal of the specified reset domain
+ * @deassert: explicitly deassert reset signal of the specified reset domain
+ */
+struct scmi_reset_ops {
+	int (*num_domains_get)(const struct scmi_handle *handle);
+	char *(*name_get)(const struct scmi_handle *handle, u32 domain);
+	int (*latency_get)(const struct scmi_handle *handle, u32 domain);
+	int (*reset)(const struct scmi_handle *handle, u32 domain);
+	int (*assert)(const struct scmi_handle *handle, u32 domain);
+	int (*deassert)(const struct scmi_handle *handle, u32 domain);
 };
 
 /**
@@ -194,6 +216,7 @@ struct scmi_sensor_ops {
  * @perf_ops: pointer to set of performance protocol operations
  * @clk_ops: pointer to set of clock protocol operations
  * @sensor_ops: pointer to set of sensor protocol operations
+ * @reset_ops: pointer to set of reset protocol operations
  * @perf_priv: pointer to private data structure specific to performance
  *	protocol(for internal use only)
  * @clk_priv: pointer to private data structure specific to clock
@@ -202,6 +225,8 @@ struct scmi_sensor_ops {
  *	protocol(for internal use only)
  * @sensor_priv: pointer to private data structure specific to sensors
  *	protocol(for internal use only)
+ * @reset_priv: pointer to private data structure specific to reset
+ *	protocol(for internal use only)
  */
 struct scmi_handle {
 	struct device *dev;
@@ -210,11 +235,13 @@ struct scmi_handle {
 	struct scmi_clk_ops *clk_ops;
 	struct scmi_power_ops *power_ops;
 	struct scmi_sensor_ops *sensor_ops;
+	struct scmi_reset_ops *reset_ops;
 	/* for protocol internal use */
 	void *perf_priv;
 	void *clk_priv;
 	void *power_priv;
 	void *sensor_priv;
+	void *reset_priv;
 };
 
 enum scmi_std_protocol {
@@ -224,6 +251,7 @@ enum scmi_std_protocol {
 	SCMI_PROTOCOL_PERF = 0x13,
 	SCMI_PROTOCOL_CLOCK = 0x14,
 	SCMI_PROTOCOL_SENSOR = 0x15,
+	SCMI_PROTOCOL_RESET = 0x16,
 };
 
 struct scmi_device {