jme: GHC register control fix for new hardware

Due to the hardware design, except the first chip on the market,
other chips needs to setup the clock source for MAC processor
implicitly through Global Host Control Register(GHC).
(Strange design huh?)

10/100M uses the PCI-E as clock source, and 1G uses GPHY.

And I reordered the code a little, to make it easier to read.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Fixed-by: "akeemting" <akeem@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

drivers/net/jme.c

@@ -435,15 +435,18 @@ jme_check_link(struct net_device *netdev, int testonly)
 					GHC_DPX);
 		switch (phylink & PHY_LINK_SPEED_MASK) {
 		case PHY_LINK_SPEED_10M:
-			ghc |= GHC_SPEED_10M;
+			ghc |= GHC_SPEED_10M |
+				GHC_TO_CLK_PCIE | GHC_TXMAC_CLK_PCIE;
 			strcat(linkmsg, "10 Mbps, ");
 			break;
 		case PHY_LINK_SPEED_100M:
-			ghc |= GHC_SPEED_100M;
+			ghc |= GHC_SPEED_100M |
+				GHC_TO_CLK_PCIE | GHC_TXMAC_CLK_PCIE;
 			strcat(linkmsg, "100 Mbps, ");
 			break;
 		case PHY_LINK_SPEED_1000M:
-			ghc |= GHC_SPEED_1000M;
+			ghc |= GHC_SPEED_1000M |
+				GHC_TO_CLK_GPHY | GHC_TXMAC_CLK_GPHY;
 			strcat(linkmsg, "1000 Mbps, ");
 			break;
 		default:
@@ -463,14 +466,6 @@ jme_check_link(struct net_device *netdev, int testonly)
 				TXTRHD_TXREN |
 				((8 << TXTRHD_TXRL_SHIFT) & TXTRHD_TXRL));
 		}
-		strcat(linkmsg, (phylink & PHY_LINK_DUPLEX) ?
-					"Full-Duplex, " :
-					"Half-Duplex, ");
-
-		if (phylink & PHY_LINK_MDI_STAT)
-			strcat(linkmsg, "MDI-X");
-		else
-			strcat(linkmsg, "MDI");
 
 		gpreg1 = GPREG1_DEFAULT;
 		if (is_buggy250(jme->pdev->device, jme->chiprev)) {
@@ -492,11 +487,17 @@ jme_check_link(struct net_device *netdev, int testonly)
 				break;
 			}
 		}
-		jwrite32(jme, JME_GPREG1, gpreg1);
 
-		jme->reg_ghc = ghc;
+		jwrite32(jme, JME_GPREG1, gpreg1);
 		jwrite32(jme, JME_GHC, ghc);
+		jme->reg_ghc = ghc;
 
+		strcat(linkmsg, (phylink & PHY_LINK_DUPLEX) ?
+					"Full-Duplex, " :
+					"Half-Duplex, ");
+		strcat(linkmsg, (phylink & PHY_LINK_MDI_STAT) ?
+					"MDI-X" :
+					"MDI");
 		msg_link(jme, "Link is up at %s.\n", linkmsg);
 		netif_carrier_on(netdev);
 	} else {

drivers/net/jme.h

@@ -827,6 +827,20 @@ enum jme_ghc_speed_val {
 	GHC_SPEED_1000M		= 0x00000030,
 };
 
+enum jme_ghc_to_clk {
+	GHC_TO_CLK_OFF		= 0x00000000,
+	GHC_TO_CLK_GPHY		= 0x00400000,
+	GHC_TO_CLK_PCIE		= 0x00800000,
+	GHC_TO_CLK_INVALID	= 0x00C00000,
+};
+
+enum jme_ghc_txmac_clk {
+	GHC_TXMAC_CLK_OFF	= 0x00000000,
+	GHC_TXMAC_CLK_GPHY	= 0x00100000,
+	GHC_TXMAC_CLK_PCIE	= 0x00200000,
+	GHC_TXMAC_CLK_INVALID	= 0x00300000,
+};
+
 /*
  * Power management control and status register
  */