Commit 5058ec4a authored by Lawrence Yu's avatar Lawrence Yu Committed by Maxime Ripard

dts: sun6i: yones toptech bs1078 v2: Add AXP221 support to dts

Enable the axp221 PMIC chip in the dts file.

Allows board to power off correctly from the poweroff command

This board requires dc1sw to be enabled in order to provide a power source
for the 5V DCDC converter that powers USB2.

This board uses dldo1 for 3.3V wifi power

This board requires dldo3 to be enabled at 2.8V in order to provide voltage
to the pullup resistors for the i2c0 bus.
Signed-off-by: default avatarLawrence Yu <lyu@micile.com>
Acked-by: default avatarChen-Yu Tsai <wens@csie.org>
Signed-off-by: default avatarMaxime Ripard <maxime.ripard@free-electrons.com>
parent 329f25b3
......@@ -113,18 +113,83 @@ &mmc0_pins_a {
allwinner,pull = <SUN4I_PINCTRL_PULL_UP>;
};
&reg_usb1_vbus {
gpio = <&pio 7 27 GPIO_ACTIVE_HIGH>;
&p2wi {
status = "okay";
axp22x: pmic@68 {
compatible = "x-powers,axp221";
reg = <0x68>;
interrupt-parent = <&nmi_intc>;
interrupts = <0 IRQ_TYPE_LEVEL_LOW>;
};
};
&usb1_vbus_pin_a {
allwinner,pins = "PH27";
#include "axp22x.dtsi"
&reg_aldo3 {
regulator-always-on;
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <3300000>;
regulator-name = "avcc";
};
&usbphy {
usb1_vbus-supply = <&reg_usb1_vbus>;
status = "okay";
&reg_dc1sw {
regulator-name = "vcc-lcd-usb2";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
};
&reg_dc5ldo {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd-cpus";
};
&reg_dcdc1 {
regulator-always-on;
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-name = "vcc-3v0";
};
&reg_dcdc2 {
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd-gpu";
};
&reg_dcdc3 {
regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd-cpu";
};
&reg_dcdc4 {
regulator-always-on;
regulator-min-microvolt = <700000>;
regulator-max-microvolt = <1320000>;
regulator-name = "vdd-sys-dll";
};
&reg_dcdc5 {
regulator-always-on;
regulator-min-microvolt = <1500000>;
regulator-max-microvolt = <1500000>;
regulator-name = "vcc-dram";
};
&reg_dldo1 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
regulator-name = "vcc-wifi";
};
/* Voltage source for I2C pullup resistors for I2C Bus 0 */
&reg_dldo3 {
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
regulator-name = "vddio-csi";
};
&uart0 {
......@@ -132,3 +197,9 @@ &uart0 {
pinctrl-0 = <&uart0_pins_a>;
status = "okay";
};
&usbphy {
usb1_vbus-supply = <&reg_dldo1>;
usb2_vbus-supply = <&reg_dc1sw>;
status = "okay";
};
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment