Commit 534c97b0 authored by Linus Torvalds's avatar Linus Torvalds

Merge branch 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip

Pull 'full dynticks' support from Ingo Molnar:
 "This tree from Frederic Weisbecker adds a new, (exciting! :-) core
  kernel feature to the timer and scheduler subsystems: 'full dynticks',
  or CONFIG_NO_HZ_FULL=y.

  This feature extends the nohz variable-size timer tick feature from
  idle to busy CPUs (running at most one task) as well, potentially
  reducing the number of timer interrupts significantly.

  This feature got motivated by real-time folks and the -rt tree, but
  the general utility and motivation of full-dynticks runs wider than
  that:

   - HPC workloads get faster: CPUs running a single task should be able
     to utilize a maximum amount of CPU power.  A periodic timer tick at
     HZ=1000 can cause a constant overhead of up to 1.0%.  This feature
     removes that overhead - and speeds up the system by 0.5%-1.0% on
     typical distro configs even on modern systems.

   - Real-time workload latency reduction: CPUs running critical tasks
     should experience as little jitter as possible.  The last remaining
     source of kernel-related jitter was the periodic timer tick.

   - A single task executing on a CPU is a pretty common situation,
     especially with an increasing number of cores/CPUs, so this feature
     helps desktop and mobile workloads as well.

  The cost of the feature is mainly related to increased timer
  reprogramming overhead when a CPU switches its tick period, and thus
  slightly longer to-idle and from-idle latency.

  Configuration-wise a third mode of operation is added to the existing
  two NOHZ kconfig modes:

   - CONFIG_HZ_PERIODIC: [formerly !CONFIG_NO_HZ], now explicitly named
     as a config option.  This is the traditional Linux periodic tick
     design: there's a HZ tick going on all the time, regardless of
     whether a CPU is idle or not.

   - CONFIG_NO_HZ_IDLE: [formerly CONFIG_NO_HZ=y], this turns off the
     periodic tick when a CPU enters idle mode.

   - CONFIG_NO_HZ_FULL: this new mode, in addition to turning off the
     tick when a CPU is idle, also slows the tick down to 1 Hz (one
     timer interrupt per second) when only a single task is running on a
     CPU.

  The .config behavior is compatible: existing !CONFIG_NO_HZ and
  CONFIG_NO_HZ=y settings get translated to the new values, without the
  user having to configure anything.  CONFIG_NO_HZ_FULL is turned off by
  default.

  This feature is based on a lot of infrastructure work that has been
  steadily going upstream in the last 2-3 cycles: related RCU support
  and non-periodic cputime support in particular is upstream already.

  This tree adds the final pieces and activates the feature.  The pull
  request is marked RFC because:

   - it's marked 64-bit only at the moment - the 32-bit support patch is
     small but did not get ready in time.

   - it has a number of fresh commits that came in after the merge
     window.  The overwhelming majority of commits are from before the
     merge window, but still some aspects of the tree are fresh and so I
     marked it RFC.

   - it's a pretty wide-reaching feature with lots of effects - and
     while the components have been in testing for some time, the full
     combination is still not very widely used.  That it's default-off
     should reduce its regression abilities and obviously there are no
     known regressions with CONFIG_NO_HZ_FULL=y enabled either.

   - the feature is not completely idempotent: there is no 100%
     equivalent replacement for a periodic scheduler/timer tick.  In
     particular there's ongoing work to map out and reduce its effects
     on scheduler load-balancing and statistics.  This should not impact
     correctness though, there are no known regressions related to this
     feature at this point.

   - it's a pretty ambitious feature that with time will likely be
     enabled by most Linux distros, and we'd like you to make input on
     its design/implementation, if you dislike some aspect we missed.
     Without flaming us to crisp! :-)

  Future plans:

   - there's ongoing work to reduce 1Hz to 0Hz, to essentially shut off
     the periodic tick altogether when there's a single busy task on a
     CPU.  We'd first like 1 Hz to be exposed more widely before we go
     for the 0 Hz target though.

   - once we reach 0 Hz we can remove the periodic tick assumption from
     nr_running>=2 as well, by essentially interrupting busy tasks only
     as frequently as the sched_latency constraints require us to do -
     once every 4-40 msecs, depending on nr_running.

  I am personally leaning towards biting the bullet and doing this in
  v3.10, like the -rt tree this effort has been going on for too long -
  but the final word is up to you as usual.

  More technical details can be found in Documentation/timers/NO_HZ.txt"

* 'timers-nohz-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (39 commits)
  sched: Keep at least 1 tick per second for active dynticks tasks
  rcu: Fix full dynticks' dependency on wide RCU nocb mode
  nohz: Protect smp_processor_id() in tick_nohz_task_switch()
  nohz_full: Add documentation.
  cputime_nsecs: use math64.h for nsec resolution conversion helpers
  nohz: Select VIRT_CPU_ACCOUNTING_GEN from full dynticks config
  nohz: Reduce overhead under high-freq idling patterns
  nohz: Remove full dynticks' superfluous dependency on RCU tree
  nohz: Fix unavailable tick_stop tracepoint in dynticks idle
  nohz: Add basic tracing
  nohz: Select wide RCU nocb for full dynticks
  nohz: Disable the tick when irq resume in full dynticks CPU
  nohz: Re-evaluate the tick for the new task after a context switch
  nohz: Prepare to stop the tick on irq exit
  nohz: Implement full dynticks kick
  nohz: Re-evaluate the tick from the scheduler IPI
  sched: New helper to prevent from stopping the tick in full dynticks
  sched: Kick full dynticks CPU that have more than one task enqueued.
  perf: New helper to prevent full dynticks CPUs from stopping tick
  perf: Kick full dynticks CPU if events rotation is needed
  ...
parents 64049d19 265f22a9
...@@ -191,7 +191,7 @@ o A CPU-bound real-time task in a CONFIG_PREEMPT_RT kernel that ...@@ -191,7 +191,7 @@ o A CPU-bound real-time task in a CONFIG_PREEMPT_RT kernel that
o A hardware or software issue shuts off the scheduler-clock o A hardware or software issue shuts off the scheduler-clock
interrupt on a CPU that is not in dyntick-idle mode. This interrupt on a CPU that is not in dyntick-idle mode. This
problem really has happened, and seems to be most likely to problem really has happened, and seems to be most likely to
result in RCU CPU stall warnings for CONFIG_NO_HZ=n kernels. result in RCU CPU stall warnings for CONFIG_NO_HZ_COMMON=n kernels.
o A bug in the RCU implementation. o A bug in the RCU implementation.
......
...@@ -131,8 +131,8 @@ sampling_rate_min: ...@@ -131,8 +131,8 @@ sampling_rate_min:
The sampling rate is limited by the HW transition latency: The sampling rate is limited by the HW transition latency:
transition_latency * 100 transition_latency * 100
Or by kernel restrictions: Or by kernel restrictions:
If CONFIG_NO_HZ is set, the limit is 10ms fixed. If CONFIG_NO_HZ_COMMON is set, the limit is 10ms fixed.
If CONFIG_NO_HZ is not set or nohz=off boot parameter is used, the If CONFIG_NO_HZ_COMMON is not set or nohz=off boot parameter is used, the
limits depend on the CONFIG_HZ option: limits depend on the CONFIG_HZ option:
HZ=1000: min=20000us (20ms) HZ=1000: min=20000us (20ms)
HZ=250: min=80000us (80ms) HZ=250: min=80000us (80ms)
......
...@@ -1964,6 +1964,14 @@ bytes respectively. Such letter suffixes can also be entirely omitted. ...@@ -1964,6 +1964,14 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
Valid arguments: on, off Valid arguments: on, off
Default: on Default: on
nohz_full= [KNL,BOOT]
In kernels built with CONFIG_NO_HZ_FULL=y, set
the specified list of CPUs whose tick will be stopped
whenever possible. The boot CPU will be forced outside
the range to maintain the timekeeping.
The CPUs in this range must also be included in the
rcu_nocbs= set.
noiotrap [SH] Disables trapped I/O port accesses. noiotrap [SH] Disables trapped I/O port accesses.
noirqdebug [X86-32] Disables the code which attempts to detect and noirqdebug [X86-32] Disables the code which attempts to detect and
......
NO_HZ: Reducing Scheduling-Clock Ticks
This document describes Kconfig options and boot parameters that can
reduce the number of scheduling-clock interrupts, thereby improving energy
efficiency and reducing OS jitter. Reducing OS jitter is important for
some types of computationally intensive high-performance computing (HPC)
applications and for real-time applications.
There are two main contexts in which the number of scheduling-clock
interrupts can be reduced compared to the old-school approach of sending
a scheduling-clock interrupt to all CPUs every jiffy whether they need
it or not (CONFIG_HZ_PERIODIC=y or CONFIG_NO_HZ=n for older kernels):
1. Idle CPUs (CONFIG_NO_HZ_IDLE=y or CONFIG_NO_HZ=y for older kernels).
2. CPUs having only one runnable task (CONFIG_NO_HZ_FULL=y).
These two cases are described in the following two sections, followed
by a third section on RCU-specific considerations and a fourth and final
section listing known issues.
IDLE CPUs
If a CPU is idle, there is little point in sending it a scheduling-clock
interrupt. After all, the primary purpose of a scheduling-clock interrupt
is to force a busy CPU to shift its attention among multiple duties,
and an idle CPU has no duties to shift its attention among.
The CONFIG_NO_HZ_IDLE=y Kconfig option causes the kernel to avoid sending
scheduling-clock interrupts to idle CPUs, which is critically important
both to battery-powered devices and to highly virtualized mainframes.
A battery-powered device running a CONFIG_HZ_PERIODIC=y kernel would
drain its battery very quickly, easily 2-3 times as fast as would the
same device running a CONFIG_NO_HZ_IDLE=y kernel. A mainframe running
1,500 OS instances might find that half of its CPU time was consumed by
unnecessary scheduling-clock interrupts. In these situations, there
is strong motivation to avoid sending scheduling-clock interrupts to
idle CPUs. That said, dyntick-idle mode is not free:
1. It increases the number of instructions executed on the path
to and from the idle loop.
2. On many architectures, dyntick-idle mode also increases the
number of expensive clock-reprogramming operations.
Therefore, systems with aggressive real-time response constraints often
run CONFIG_HZ_PERIODIC=y kernels (or CONFIG_NO_HZ=n for older kernels)
in order to avoid degrading from-idle transition latencies.
An idle CPU that is not receiving scheduling-clock interrupts is said to
be "dyntick-idle", "in dyntick-idle mode", "in nohz mode", or "running
tickless". The remainder of this document will use "dyntick-idle mode".
There is also a boot parameter "nohz=" that can be used to disable
dyntick-idle mode in CONFIG_NO_HZ_IDLE=y kernels by specifying "nohz=off".
By default, CONFIG_NO_HZ_IDLE=y kernels boot with "nohz=on", enabling
dyntick-idle mode.
CPUs WITH ONLY ONE RUNNABLE TASK
If a CPU has only one runnable task, there is little point in sending it
a scheduling-clock interrupt because there is no other task to switch to.
The CONFIG_NO_HZ_FULL=y Kconfig option causes the kernel to avoid
sending scheduling-clock interrupts to CPUs with a single runnable task,
and such CPUs are said to be "adaptive-ticks CPUs". This is important
for applications with aggressive real-time response constraints because
it allows them to improve their worst-case response times by the maximum
duration of a scheduling-clock interrupt. It is also important for
computationally intensive short-iteration workloads: If any CPU is
delayed during a given iteration, all the other CPUs will be forced to
wait idle while the delayed CPU finishes. Thus, the delay is multiplied
by one less than the number of CPUs. In these situations, there is
again strong motivation to avoid sending scheduling-clock interrupts.
By default, no CPU will be an adaptive-ticks CPU. The "nohz_full="
boot parameter specifies the adaptive-ticks CPUs. For example,
"nohz_full=1,6-8" says that CPUs 1, 6, 7, and 8 are to be adaptive-ticks
CPUs. Note that you are prohibited from marking all of the CPUs as
adaptive-tick CPUs: At least one non-adaptive-tick CPU must remain
online to handle timekeeping tasks in order to ensure that system calls
like gettimeofday() returns accurate values on adaptive-tick CPUs.
(This is not an issue for CONFIG_NO_HZ_IDLE=y because there are no
running user processes to observe slight drifts in clock rate.)
Therefore, the boot CPU is prohibited from entering adaptive-ticks
mode. Specifying a "nohz_full=" mask that includes the boot CPU will
result in a boot-time error message, and the boot CPU will be removed
from the mask.
Alternatively, the CONFIG_NO_HZ_FULL_ALL=y Kconfig parameter specifies
that all CPUs other than the boot CPU are adaptive-ticks CPUs. This
Kconfig parameter will be overridden by the "nohz_full=" boot parameter,
so that if both the CONFIG_NO_HZ_FULL_ALL=y Kconfig parameter and
the "nohz_full=1" boot parameter is specified, the boot parameter will
prevail so that only CPU 1 will be an adaptive-ticks CPU.
Finally, adaptive-ticks CPUs must have their RCU callbacks offloaded.
This is covered in the "RCU IMPLICATIONS" section below.
Normally, a CPU remains in adaptive-ticks mode as long as possible.
In particular, transitioning to kernel mode does not automatically change
the mode. Instead, the CPU will exit adaptive-ticks mode only if needed,
for example, if that CPU enqueues an RCU callback.
Just as with dyntick-idle mode, the benefits of adaptive-tick mode do
not come for free:
1. CONFIG_NO_HZ_FULL selects CONFIG_NO_HZ_COMMON, so you cannot run
adaptive ticks without also running dyntick idle. This dependency
extends down into the implementation, so that all of the costs
of CONFIG_NO_HZ_IDLE are also incurred by CONFIG_NO_HZ_FULL.
2. The user/kernel transitions are slightly more expensive due
to the need to inform kernel subsystems (such as RCU) about
the change in mode.
3. POSIX CPU timers on adaptive-tick CPUs may miss their deadlines
(perhaps indefinitely) because they currently rely on
scheduling-tick interrupts. This will likely be fixed in
one of two ways: (1) Prevent CPUs with POSIX CPU timers from
entering adaptive-tick mode, or (2) Use hrtimers or other
adaptive-ticks-immune mechanism to cause the POSIX CPU timer to
fire properly.
4. If there are more perf events pending than the hardware can
accommodate, they are normally round-robined so as to collect
all of them over time. Adaptive-tick mode may prevent this
round-robining from happening. This will likely be fixed by
preventing CPUs with large numbers of perf events pending from
entering adaptive-tick mode.
5. Scheduler statistics for adaptive-tick CPUs may be computed
slightly differently than those for non-adaptive-tick CPUs.
This might in turn perturb load-balancing of real-time tasks.
6. The LB_BIAS scheduler feature is disabled by adaptive ticks.
Although improvements are expected over time, adaptive ticks is quite
useful for many types of real-time and compute-intensive applications.
However, the drawbacks listed above mean that adaptive ticks should not
(yet) be enabled by default.
RCU IMPLICATIONS
There are situations in which idle CPUs cannot be permitted to
enter either dyntick-idle mode or adaptive-tick mode, the most
common being when that CPU has RCU callbacks pending.
The CONFIG_RCU_FAST_NO_HZ=y Kconfig option may be used to cause such CPUs
to enter dyntick-idle mode or adaptive-tick mode anyway. In this case,
a timer will awaken these CPUs every four jiffies in order to ensure
that the RCU callbacks are processed in a timely fashion.
Another approach is to offload RCU callback processing to "rcuo" kthreads
using the CONFIG_RCU_NOCB_CPU=y Kconfig option. The specific CPUs to
offload may be selected via several methods:
1. One of three mutually exclusive Kconfig options specify a
build-time default for the CPUs to offload:
a. The CONFIG_RCU_NOCB_CPU_NONE=y Kconfig option results in
no CPUs being offloaded.
b. The CONFIG_RCU_NOCB_CPU_ZERO=y Kconfig option causes
CPU 0 to be offloaded.
c. The CONFIG_RCU_NOCB_CPU_ALL=y Kconfig option causes all
CPUs to be offloaded. Note that the callbacks will be
offloaded to "rcuo" kthreads, and that those kthreads
will in fact run on some CPU. However, this approach
gives fine-grained control on exactly which CPUs the
callbacks run on, along with their scheduling priority
(including the default of SCHED_OTHER), and it further
allows this control to be varied dynamically at runtime.
2. The "rcu_nocbs=" kernel boot parameter, which takes a comma-separated
list of CPUs and CPU ranges, for example, "1,3-5" selects CPUs 1,
3, 4, and 5. The specified CPUs will be offloaded in addition to
any CPUs specified as offloaded by CONFIG_RCU_NOCB_CPU_ZERO=y or
CONFIG_RCU_NOCB_CPU_ALL=y. This means that the "rcu_nocbs=" boot
parameter has no effect for kernels built with RCU_NOCB_CPU_ALL=y.
The offloaded CPUs will never queue RCU callbacks, and therefore RCU
never prevents offloaded CPUs from entering either dyntick-idle mode
or adaptive-tick mode. That said, note that it is up to userspace to
pin the "rcuo" kthreads to specific CPUs if desired. Otherwise, the
scheduler will decide where to run them, which might or might not be
where you want them to run.
KNOWN ISSUES
o Dyntick-idle slows transitions to and from idle slightly.
In practice, this has not been a problem except for the most
aggressive real-time workloads, which have the option of disabling
dyntick-idle mode, an option that most of them take. However,
some workloads will no doubt want to use adaptive ticks to
eliminate scheduling-clock interrupt latencies. Here are some
options for these workloads:
a. Use PMQOS from userspace to inform the kernel of your
latency requirements (preferred).
b. On x86 systems, use the "idle=mwait" boot parameter.
c. On x86 systems, use the "intel_idle.max_cstate=" to limit
` the maximum C-state depth.
d. On x86 systems, use the "idle=poll" boot parameter.
However, please note that use of this parameter can cause
your CPU to overheat, which may cause thermal throttling
to degrade your latencies -- and that this degradation can
be even worse than that of dyntick-idle. Furthermore,
this parameter effectively disables Turbo Mode on Intel
CPUs, which can significantly reduce maximum performance.
o Adaptive-ticks slows user/kernel transitions slightly.
This is not expected to be a problem for computationally intensive
workloads, which have few such transitions. Careful benchmarking
will be required to determine whether or not other workloads
are significantly affected by this effect.
o Adaptive-ticks does not do anything unless there is only one
runnable task for a given CPU, even though there are a number
of other situations where the scheduling-clock tick is not
needed. To give but one example, consider a CPU that has one
runnable high-priority SCHED_FIFO task and an arbitrary number
of low-priority SCHED_OTHER tasks. In this case, the CPU is
required to run the SCHED_FIFO task until it either blocks or
some other higher-priority task awakens on (or is assigned to)
this CPU, so there is no point in sending a scheduling-clock
interrupt to this CPU. However, the current implementation
nevertheless sends scheduling-clock interrupts to CPUs having a
single runnable SCHED_FIFO task and multiple runnable SCHED_OTHER
tasks, even though these interrupts are unnecessary.
Better handling of these sorts of situations is future work.
o A reboot is required to reconfigure both adaptive idle and RCU
callback offloading. Runtime reconfiguration could be provided
if needed, however, due to the complexity of reconfiguring RCU at
runtime, there would need to be an earthshakingly good reason.
Especially given that you have the straightforward option of
simply offloading RCU callbacks from all CPUs and pinning them
where you want them whenever you want them pinned.
o Additional configuration is required to deal with other sources
of OS jitter, including interrupts and system-utility tasks
and processes. This configuration normally involves binding
interrupts and tasks to particular CPUs.
o Some sources of OS jitter can currently be eliminated only by
constraining the workload. For example, the only way to eliminate
OS jitter due to global TLB shootdowns is to avoid the unmapping
operations (such as kernel module unload operations) that
result in these shootdowns. For another example, page faults
and TLB misses can be reduced (and in some cases eliminated) by
using huge pages and by constraining the amount of memory used
by the application. Pre-faulting the working set can also be
helpful, especially when combined with the mlock() and mlockall()
system calls.
o Unless all CPUs are idle, at least one CPU must keep the
scheduling-clock interrupt going in order to support accurate
timekeeping.
o If there are adaptive-ticks CPUs, there will be at least one
CPU keeping the scheduling-clock interrupt going, even if all
CPUs are otherwise idle.
...@@ -30,8 +30,8 @@ DEFINE(UM_NSEC_PER_USEC, NSEC_PER_USEC); ...@@ -30,8 +30,8 @@ DEFINE(UM_NSEC_PER_USEC, NSEC_PER_USEC);
#ifdef CONFIG_PRINTK #ifdef CONFIG_PRINTK
DEFINE(UML_CONFIG_PRINTK, CONFIG_PRINTK); DEFINE(UML_CONFIG_PRINTK, CONFIG_PRINTK);
#endif #endif
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
DEFINE(UML_CONFIG_NO_HZ, CONFIG_NO_HZ); DEFINE(UML_CONFIG_NO_HZ_COMMON, CONFIG_NO_HZ_COMMON);
#endif #endif
#ifdef CONFIG_UML_X86 #ifdef CONFIG_UML_X86
DEFINE(UML_CONFIG_UML_X86, CONFIG_UML_X86); DEFINE(UML_CONFIG_UML_X86, CONFIG_UML_X86);
......
...@@ -79,7 +79,7 @@ long long os_nsecs(void) ...@@ -79,7 +79,7 @@ long long os_nsecs(void)
return timeval_to_ns(&tv); return timeval_to_ns(&tv);
} }
#ifdef UML_CONFIG_NO_HZ #ifdef UML_CONFIG_NO_HZ_COMMON
static int after_sleep_interval(struct timespec *ts) static int after_sleep_interval(struct timespec *ts)
{ {
return 0; return 0;
......
...@@ -16,21 +16,27 @@ ...@@ -16,21 +16,27 @@
#ifndef _ASM_GENERIC_CPUTIME_NSECS_H #ifndef _ASM_GENERIC_CPUTIME_NSECS_H
#define _ASM_GENERIC_CPUTIME_NSECS_H #define _ASM_GENERIC_CPUTIME_NSECS_H
#include <linux/math64.h>
typedef u64 __nocast cputime_t; typedef u64 __nocast cputime_t;
typedef u64 __nocast cputime64_t; typedef u64 __nocast cputime64_t;
#define cputime_one_jiffy jiffies_to_cputime(1) #define cputime_one_jiffy jiffies_to_cputime(1)
#define cputime_div(__ct, divisor) div_u64((__force u64)__ct, divisor)
#define cputime_div_rem(__ct, divisor, remainder) \
div_u64_rem((__force u64)__ct, divisor, remainder);
/* /*
* Convert cputime <-> jiffies (HZ) * Convert cputime <-> jiffies (HZ)
*/ */
#define cputime_to_jiffies(__ct) \ #define cputime_to_jiffies(__ct) \
((__force u64)(__ct) / (NSEC_PER_SEC / HZ)) cputime_div(__ct, NSEC_PER_SEC / HZ)
#define cputime_to_scaled(__ct) (__ct) #define cputime_to_scaled(__ct) (__ct)
#define jiffies_to_cputime(__jif) \ #define jiffies_to_cputime(__jif) \
(__force cputime_t)((__jif) * (NSEC_PER_SEC / HZ)) (__force cputime_t)((__jif) * (NSEC_PER_SEC / HZ))
#define cputime64_to_jiffies64(__ct) \ #define cputime64_to_jiffies64(__ct) \
((__force u64)(__ct) / (NSEC_PER_SEC / HZ)) cputime_div(__ct, NSEC_PER_SEC / HZ)
#define jiffies64_to_cputime64(__jif) \ #define jiffies64_to_cputime64(__jif) \
(__force cputime64_t)((__jif) * (NSEC_PER_SEC / HZ)) (__force cputime64_t)((__jif) * (NSEC_PER_SEC / HZ))
...@@ -45,7 +51,7 @@ typedef u64 __nocast cputime64_t; ...@@ -45,7 +51,7 @@ typedef u64 __nocast cputime64_t;
* Convert cputime <-> microseconds * Convert cputime <-> microseconds
*/ */
#define cputime_to_usecs(__ct) \ #define cputime_to_usecs(__ct) \
((__force u64)(__ct) / NSEC_PER_USEC) cputime_div(__ct, NSEC_PER_USEC)
#define usecs_to_cputime(__usecs) \ #define usecs_to_cputime(__usecs) \
(__force cputime_t)((__usecs) * NSEC_PER_USEC) (__force cputime_t)((__usecs) * NSEC_PER_USEC)
#define usecs_to_cputime64(__usecs) \ #define usecs_to_cputime64(__usecs) \
...@@ -55,7 +61,7 @@ typedef u64 __nocast cputime64_t; ...@@ -55,7 +61,7 @@ typedef u64 __nocast cputime64_t;
* Convert cputime <-> seconds * Convert cputime <-> seconds
*/ */
#define cputime_to_secs(__ct) \ #define cputime_to_secs(__ct) \
((__force u64)(__ct) / NSEC_PER_SEC) cputime_div(__ct, NSEC_PER_SEC)
#define secs_to_cputime(__secs) \ #define secs_to_cputime(__secs) \
(__force cputime_t)((__secs) * NSEC_PER_SEC) (__force cputime_t)((__secs) * NSEC_PER_SEC)
...@@ -69,8 +75,10 @@ static inline cputime_t timespec_to_cputime(const struct timespec *val) ...@@ -69,8 +75,10 @@ static inline cputime_t timespec_to_cputime(const struct timespec *val)
} }
static inline void cputime_to_timespec(const cputime_t ct, struct timespec *val) static inline void cputime_to_timespec(const cputime_t ct, struct timespec *val)
{ {
val->tv_sec = (__force u64) ct / NSEC_PER_SEC; u32 rem;
val->tv_nsec = (__force u64) ct % NSEC_PER_SEC;
val->tv_sec = cputime_div_rem(ct, NSEC_PER_SEC, &rem);
val->tv_nsec = rem;
} }
/* /*
...@@ -83,15 +91,17 @@ static inline cputime_t timeval_to_cputime(const struct timeval *val) ...@@ -83,15 +91,17 @@ static inline cputime_t timeval_to_cputime(const struct timeval *val)
} }
static inline void cputime_to_timeval(const cputime_t ct, struct timeval *val) static inline void cputime_to_timeval(const cputime_t ct, struct timeval *val)
{ {
val->tv_sec = (__force u64) ct / NSEC_PER_SEC; u32 rem;
val->tv_usec = ((__force u64) ct % NSEC_PER_SEC) / NSEC_PER_USEC;
val->tv_sec = cputime_div_rem(ct, NSEC_PER_SEC, &rem);
val->tv_usec = rem / NSEC_PER_USEC;
} }
/* /*
* Convert cputime <-> clock (USER_HZ) * Convert cputime <-> clock (USER_HZ)
*/ */
#define cputime_to_clock_t(__ct) \ #define cputime_to_clock_t(__ct) \
((__force u64)(__ct) / (NSEC_PER_SEC / USER_HZ)) cputime_div(__ct, (NSEC_PER_SEC / USER_HZ))
#define clock_t_to_cputime(__x) \ #define clock_t_to_cputime(__x) \
(__force cputime_t)((__x) * (NSEC_PER_SEC / USER_HZ)) (__force cputime_t)((__x) * (NSEC_PER_SEC / USER_HZ))
......
...@@ -788,6 +788,12 @@ static inline int __perf_event_disable(void *info) { return -1; } ...@@ -788,6 +788,12 @@ static inline int __perf_event_disable(void *info) { return -1; }
static inline void perf_event_task_tick(void) { } static inline void perf_event_task_tick(void) { }
#endif #endif
#if defined(CONFIG_PERF_EVENTS) && defined(CONFIG_NO_HZ_FULL)
extern bool perf_event_can_stop_tick(void);
#else
static inline bool perf_event_can_stop_tick(void) { return true; }
#endif
#if defined(CONFIG_PERF_EVENTS) && defined(CONFIG_CPU_SUP_INTEL) #if defined(CONFIG_PERF_EVENTS) && defined(CONFIG_CPU_SUP_INTEL)
extern void perf_restore_debug_store(void); extern void perf_restore_debug_store(void);
#else #else
......
...@@ -123,6 +123,8 @@ void run_posix_cpu_timers(struct task_struct *task); ...@@ -123,6 +123,8 @@ void run_posix_cpu_timers(struct task_struct *task);
void posix_cpu_timers_exit(struct task_struct *task); void posix_cpu_timers_exit(struct task_struct *task);
void posix_cpu_timers_exit_group(struct task_struct *task); void posix_cpu_timers_exit_group(struct task_struct *task);
bool posix_cpu_timers_can_stop_tick(struct task_struct *tsk);
void set_process_cpu_timer(struct task_struct *task, unsigned int clock_idx, void set_process_cpu_timer(struct task_struct *task, unsigned int clock_idx,
cputime_t *newval, cputime_t *oldval); cputime_t *newval, cputime_t *oldval);
......
...@@ -1000,4 +1000,11 @@ static inline notrace void rcu_read_unlock_sched_notrace(void) ...@@ -1000,4 +1000,11 @@ static inline notrace void rcu_read_unlock_sched_notrace(void)
#define kfree_rcu(ptr, rcu_head) \ #define kfree_rcu(ptr, rcu_head) \
__kfree_rcu(&((ptr)->rcu_head), offsetof(typeof(*(ptr)), rcu_head)) __kfree_rcu(&((ptr)->rcu_head), offsetof(typeof(*(ptr)), rcu_head))
#ifdef CONFIG_RCU_NOCB_CPU
extern bool rcu_is_nocb_cpu(int cpu);
#else
static inline bool rcu_is_nocb_cpu(int cpu) { return false; }
#endif /* #else #ifdef CONFIG_RCU_NOCB_CPU */
#endif /* __LINUX_RCUPDATE_H */ #endif /* __LINUX_RCUPDATE_H */
...@@ -231,7 +231,7 @@ extern void init_idle_bootup_task(struct task_struct *idle); ...@@ -231,7 +231,7 @@ extern void init_idle_bootup_task(struct task_struct *idle);
extern int runqueue_is_locked(int cpu); extern int runqueue_is_locked(int cpu);
#if defined(CONFIG_SMP) && defined(CONFIG_NO_HZ) #if defined(CONFIG_SMP) && defined(CONFIG_NO_HZ_COMMON)
extern void nohz_balance_enter_idle(int cpu); extern void nohz_balance_enter_idle(int cpu);
extern void set_cpu_sd_state_idle(void); extern void set_cpu_sd_state_idle(void);
extern int get_nohz_timer_target(void); extern int get_nohz_timer_target(void);
...@@ -1764,13 +1764,13 @@ static inline int set_cpus_allowed_ptr(struct task_struct *p, ...@@ -1764,13 +1764,13 @@ static inline int set_cpus_allowed_ptr(struct task_struct *p,
} }
#endif #endif
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
void calc_load_enter_idle(void); void calc_load_enter_idle(void);
void calc_load_exit_idle(void); void calc_load_exit_idle(void);
#else #else
static inline void calc_load_enter_idle(void) { } static inline void calc_load_enter_idle(void) { }
static inline void calc_load_exit_idle(void) { } static inline void calc_load_exit_idle(void) { }
#endif /* CONFIG_NO_HZ */ #endif /* CONFIG_NO_HZ_COMMON */
#ifndef CONFIG_CPUMASK_OFFSTACK #ifndef CONFIG_CPUMASK_OFFSTACK
static inline int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask) static inline int set_cpus_allowed(struct task_struct *p, cpumask_t new_mask)
...@@ -1856,10 +1856,17 @@ extern void idle_task_exit(void); ...@@ -1856,10 +1856,17 @@ extern void idle_task_exit(void);
static inline void idle_task_exit(void) {} static inline void idle_task_exit(void) {}
#endif #endif
#if defined(CONFIG_NO_HZ) && defined(CONFIG_SMP) #if defined(CONFIG_NO_HZ_COMMON) && defined(CONFIG_SMP)
extern void wake_up_idle_cpu(int cpu); extern void wake_up_nohz_cpu(int cpu);
#else #else
static inline void wake_up_idle_cpu(int cpu) { } static inline void wake_up_nohz_cpu(int cpu) { }
#endif
#ifdef CONFIG_NO_HZ_FULL
extern bool sched_can_stop_tick(void);
extern u64 scheduler_tick_max_deferment(void);
#else
static inline bool sched_can_stop_tick(void) { return false; }
#endif #endif
#ifdef CONFIG_SCHED_AUTOGROUP #ifdef CONFIG_SCHED_AUTOGROUP
......
...@@ -82,7 +82,7 @@ extern int tick_program_event(ktime_t expires, int force); ...@@ -82,7 +82,7 @@ extern int tick_program_event(ktime_t expires, int force);
extern void tick_setup_sched_timer(void); extern void tick_setup_sched_timer(void);
# endif # endif
# if defined CONFIG_NO_HZ || defined CONFIG_HIGH_RES_TIMERS # if defined CONFIG_NO_HZ_COMMON || defined CONFIG_HIGH_RES_TIMERS
extern void tick_cancel_sched_timer(int cpu); extern void tick_cancel_sched_timer(int cpu);
# else # else
static inline void tick_cancel_sched_timer(int cpu) { } static inline void tick_cancel_sched_timer(int cpu) { }
...@@ -123,7 +123,7 @@ static inline void tick_check_idle(int cpu) { } ...@@ -123,7 +123,7 @@ static inline void tick_check_idle(int cpu) { }
static inline int tick_oneshot_mode_active(void) { return 0; } static inline int tick_oneshot_mode_active(void) { return 0; }
#endif /* !CONFIG_GENERIC_CLOCKEVENTS */ #endif /* !CONFIG_GENERIC_CLOCKEVENTS */
# ifdef CONFIG_NO_HZ # ifdef CONFIG_NO_HZ_COMMON
DECLARE_PER_CPU(struct tick_sched, tick_cpu_sched); DECLARE_PER_CPU(struct tick_sched, tick_cpu_sched);
static inline int tick_nohz_tick_stopped(void) static inline int tick_nohz_tick_stopped(void)
...@@ -138,7 +138,7 @@ extern ktime_t tick_nohz_get_sleep_length(void); ...@@ -138,7 +138,7 @@ extern ktime_t tick_nohz_get_sleep_length(void);
extern u64 get_cpu_idle_time_us(int cpu, u64 *last_update_time); extern u64 get_cpu_idle_time_us(int cpu, u64 *last_update_time);
extern u64 get_cpu_iowait_time_us(int cpu, u64 *last_update_time); extern u64 get_cpu_iowait_time_us(int cpu, u64 *last_update_time);
# else /* !CONFIG_NO_HZ */ # else /* !CONFIG_NO_HZ_COMMON */
static inline int tick_nohz_tick_stopped(void) static inline int tick_nohz_tick_stopped(void)
{ {
return 0; return 0;
...@@ -155,7 +155,24 @@ static inline ktime_t tick_nohz_get_sleep_length(void) ...@@ -155,7 +155,24 @@ static inline ktime_t tick_nohz_get_sleep_length(void)
} }
static inline u64 get_cpu_idle_time_us(int cpu, u64 *unused) { return -1; } static inline u64 get_cpu_idle_time_us(int cpu, u64 *unused) { return -1; }
static inline u64 get_cpu_iowait_time_us(int cpu, u64 *unused) { return -1; } static inline u64 get_cpu_iowait_time_us(int cpu, u64 *unused) { return -1; }
# endif /* !NO_HZ */ # endif /* !CONFIG_NO_HZ_COMMON */
#ifdef CONFIG_NO_HZ_FULL
extern void tick_nohz_init(void);
extern int tick_nohz_full_cpu(int cpu);
extern void tick_nohz_full_check(void);
extern void tick_nohz_full_kick(void);
extern void tick_nohz_full_kick_all(void);
extern void tick_nohz_task_switch(struct task_struct *tsk);
#else
static inline void tick_nohz_init(void) { }
static inline int tick_nohz_full_cpu(int cpu) { return 0; }
static inline void tick_nohz_full_check(void) { }
static inline void tick_nohz_full_kick(void) { }
static inline void tick_nohz_full_kick_all(void) { }
static inline void tick_nohz_task_switch(struct task_struct *tsk) { }
#endif
# ifdef CONFIG_CPU_IDLE_GOV_MENU # ifdef CONFIG_CPU_IDLE_GOV_MENU
extern void menu_hrtimer_cancel(void); extern void menu_hrtimer_cancel(void);
......
...@@ -323,6 +323,27 @@ TRACE_EVENT(itimer_expire, ...@@ -323,6 +323,27 @@ TRACE_EVENT(itimer_expire,
(int) __entry->pid, (unsigned long long)__entry->now) (int) __entry->pid, (unsigned long long)__entry->now)
); );
#ifdef CONFIG_NO_HZ_COMMON
TRACE_EVENT(tick_stop,
TP_PROTO(int success, char *error_msg),
TP_ARGS(success, error_msg),
TP_STRUCT__entry(
__field( int , success )
__string( msg, error_msg )
),
TP_fast_assign(
__entry->success = success;
__assign_str(msg, error_msg);
),
TP_printk("success=%s msg=%s", __entry->success ? "yes" : "no", __get_str(msg))
);
#endif
#endif /* _TRACE_TIMER_H */ #endif /* _TRACE_TIMER_H */
/* This part must be outside protection */ /* This part must be outside protection */
......
...@@ -302,7 +302,7 @@ choice ...@@ -302,7 +302,7 @@ choice
# Kind of a stub config for the pure tick based cputime accounting # Kind of a stub config for the pure tick based cputime accounting
config TICK_CPU_ACCOUNTING config TICK_CPU_ACCOUNTING
bool "Simple tick based cputime accounting" bool "Simple tick based cputime accounting"
depends on !S390 depends on !S390 && !NO_HZ_FULL
help help
This is the basic tick based cputime accounting that maintains This is the basic tick based cputime accounting that maintains
statistics about user, system and idle time spent on per jiffies statistics about user, system and idle time spent on per jiffies
...@@ -312,7 +312,7 @@ config TICK_CPU_ACCOUNTING ...@@ -312,7 +312,7 @@ config TICK_CPU_ACCOUNTING
config VIRT_CPU_ACCOUNTING_NATIVE config VIRT_CPU_ACCOUNTING_NATIVE
bool "Deterministic task and CPU time accounting" bool "Deterministic task and CPU time accounting"
depends on HAVE_VIRT_CPU_ACCOUNTING depends on HAVE_VIRT_CPU_ACCOUNTING && !NO_HZ_FULL
select VIRT_CPU_ACCOUNTING select VIRT_CPU_ACCOUNTING
help help
Select this option to enable more accurate task and CPU time Select this option to enable more accurate task and CPU time
...@@ -342,7 +342,7 @@ config VIRT_CPU_ACCOUNTING_GEN ...@@ -342,7 +342,7 @@ config VIRT_CPU_ACCOUNTING_GEN
config IRQ_TIME_ACCOUNTING config IRQ_TIME_ACCOUNTING
bool "Fine granularity task level IRQ time accounting" bool "Fine granularity task level IRQ time accounting"
depends on HAVE_IRQ_TIME_ACCOUNTING depends on HAVE_IRQ_TIME_ACCOUNTING && !NO_HZ_FULL
help help
Select this option to enable fine granularity task irq time Select this option to enable fine granularity task irq time
accounting. This is done by reading a timestamp on each accounting. This is done by reading a timestamp on each
...@@ -576,7 +576,7 @@ config RCU_FANOUT_EXACT ...@@ -576,7 +576,7 @@ config RCU_FANOUT_EXACT
config RCU_FAST_NO_HZ config RCU_FAST_NO_HZ
bool "Accelerate last non-dyntick-idle CPU's grace periods" bool "Accelerate last non-dyntick-idle CPU's grace periods"
depends on NO_HZ && SMP depends on NO_HZ_COMMON && SMP
default n default n
help help
This option permits CPUs to enter dynticks-idle state even if This option permits CPUs to enter dynticks-idle state even if
...@@ -687,7 +687,7 @@ choice ...@@ -687,7 +687,7 @@ choice
config RCU_NOCB_CPU_NONE config RCU_NOCB_CPU_NONE
bool "No build_forced no-CBs CPUs" bool "No build_forced no-CBs CPUs"
depends on RCU_NOCB_CPU depends on RCU_NOCB_CPU && !NO_HZ_FULL
help help
This option does not force any of the CPUs to be no-CBs CPUs. This option does not force any of the CPUs to be no-CBs CPUs.
Only CPUs designated by the rcu_nocbs= boot parameter will be Only CPUs designated by the rcu_nocbs= boot parameter will be
...@@ -695,7 +695,7 @@ config RCU_NOCB_CPU_NONE ...@@ -695,7 +695,7 @@ config RCU_NOCB_CPU_NONE
config RCU_NOCB_CPU_ZERO config RCU_NOCB_CPU_ZERO
bool "CPU 0 is a build_forced no-CBs CPU" bool "CPU 0 is a build_forced no-CBs CPU"
depends on RCU_NOCB_CPU depends on RCU_NOCB_CPU && !NO_HZ_FULL
help help
This option forces CPU 0 to be a no-CBs CPU. Additional CPUs This option forces CPU 0 to be a no-CBs CPU. Additional CPUs
may be designated as no-CBs CPUs using the rcu_nocbs= boot may be designated as no-CBs CPUs using the rcu_nocbs= boot
......
...@@ -544,6 +544,7 @@ asmlinkage void __init start_kernel(void) ...@@ -544,6 +544,7 @@ asmlinkage void __init start_kernel(void)
idr_init_cache(); idr_init_cache();
perf_event_init(); perf_event_init();
rcu_init(); rcu_init();
tick_nohz_init();
radix_tree_init(); radix_tree_init();
/* init some links before init_ISA_irqs() */ /* init some links before init_ISA_irqs() */
early_irq_init(); early_irq_init();
......
...@@ -18,6 +18,7 @@ ...@@ -18,6 +18,7 @@
#include <linux/poll.h> #include <linux/poll.h>
#include <linux/slab.h> #include <linux/slab.h>
#include <linux/hash.h> #include <linux/hash.h>
#include <linux/tick.h>
#include <linux/sysfs.h> #include <linux/sysfs.h>
#include <linux/dcache.h> #include <linux/dcache.h>
#include <linux/percpu.h> #include <linux/percpu.h>
...@@ -685,8 +686,12 @@ static void perf_pmu_rotate_start(struct pmu *pmu) ...@@ -685,8 +686,12 @@ static void perf_pmu_rotate_start(struct pmu *pmu)
WARN_ON(!irqs_disabled()); WARN_ON(!irqs_disabled());
if (list_empty(&cpuctx->rotation_list)) if (list_empty(&cpuctx->rotation_list)) {
int was_empty = list_empty(head);
list_add(&cpuctx->rotation_list, head); list_add(&cpuctx->rotation_list, head);
if (was_empty)
tick_nohz_full_kick();
}
} }
static void get_ctx(struct perf_event_context *ctx) static void get_ctx(struct perf_event_context *ctx)
...@@ -2591,6 +2596,16 @@ static void perf_rotate_context(struct perf_cpu_context *cpuctx) ...@@ -2591,6 +2596,16 @@ static void perf_rotate_context(struct perf_cpu_context *cpuctx)
list_del_init(&cpuctx->rotation_list); list_del_init(&cpuctx->rotation_list);
} }
#ifdef CONFIG_NO_HZ_FULL
bool perf_event_can_stop_tick(void)
{
if (list_empty(&__get_cpu_var(rotation_list)))
return true;
else
return false;
}
#endif
void perf_event_task_tick(void) void perf_event_task_tick(void)
{ {
struct list_head *head = &__get_cpu_var(rotation_list); struct list_head *head = &__get_cpu_var(rotation_list);
......
...@@ -172,7 +172,7 @@ struct hrtimer_clock_base *lock_hrtimer_base(const struct hrtimer *timer, ...@@ -172,7 +172,7 @@ struct hrtimer_clock_base *lock_hrtimer_base(const struct hrtimer *timer,
*/ */
static int hrtimer_get_target(int this_cpu, int pinned) static int hrtimer_get_target(int this_cpu, int pinned)
{ {
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
if (!pinned && get_sysctl_timer_migration() && idle_cpu(this_cpu)) if (!pinned && get_sysctl_timer_migration() && idle_cpu(this_cpu))
return get_nohz_timer_target(); return get_nohz_timer_target();
#endif #endif
...@@ -1125,7 +1125,7 @@ ktime_t hrtimer_get_remaining(const struct hrtimer *timer) ...@@ -1125,7 +1125,7 @@ ktime_t hrtimer_get_remaining(const struct hrtimer *timer)
} }
EXPORT_SYMBOL_GPL(hrtimer_get_remaining); EXPORT_SYMBOL_GPL(hrtimer_get_remaining);
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/** /**
* hrtimer_get_next_event - get the time until next expiry event * hrtimer_get_next_event - get the time until next expiry event
* *
......
...@@ -10,6 +10,8 @@ ...@@ -10,6 +10,8 @@
#include <linux/kernel_stat.h> #include <linux/kernel_stat.h>
#include <trace/events/timer.h> #include <trace/events/timer.h>
#include <linux/random.h> #include <linux/random.h>
#include <linux/tick.h>
#include <linux/workqueue.h>
/* /*
* Called after updating RLIMIT_CPU to run cpu timer and update * Called after updating RLIMIT_CPU to run cpu timer and update
...@@ -153,6 +155,21 @@ static void bump_cpu_timer(struct k_itimer *timer, ...@@ -153,6 +155,21 @@ static void bump_cpu_timer(struct k_itimer *timer,
} }
} }
/**
* task_cputime_zero - Check a task_cputime struct for all zero fields.
*
* @cputime: The struct to compare.
*
* Checks @cputime to see if all fields are zero. Returns true if all fields
* are zero, false if any field is nonzero.
*/
static inline int task_cputime_zero(const struct task_cputime *cputime)
{
if (!cputime->utime && !cputime->stime && !cputime->sum_exec_runtime)
return 1;
return 0;
}
static inline cputime_t prof_ticks(struct task_struct *p) static inline cputime_t prof_ticks(struct task_struct *p)
{ {
cputime_t utime, stime; cputime_t utime, stime;
...@@ -636,6 +653,37 @@ static int cpu_timer_sample_group(const clockid_t which_clock, ...@@ -636,6 +653,37 @@ static int cpu_timer_sample_group(const clockid_t which_clock,
return 0; return 0;
} }
#ifdef CONFIG_NO_HZ_FULL
static void nohz_kick_work_fn(struct work_struct *work)
{
tick_nohz_full_kick_all();
}
static DECLARE_WORK(nohz_kick_work, nohz_kick_work_fn);
/*
* We need the IPIs to be sent from sane process context.
* The posix cpu timers are always set with irqs disabled.
*/
static void posix_cpu_timer_kick_nohz(void)
{
schedule_work(&nohz_kick_work);
}
bool posix_cpu_timers_can_stop_tick(struct task_struct *tsk)
{
if (!task_cputime_zero(&tsk->cputime_expires))
return false;
if (tsk->signal->cputimer.running)
return false;
return true;
}
#else
static inline void posix_cpu_timer_kick_nohz(void) { }
#endif
/* /*
* Guts of sys_timer_settime for CPU timers. * Guts of sys_timer_settime for CPU timers.
* This is called with the timer locked and interrupts disabled. * This is called with the timer locked and interrupts disabled.
...@@ -794,6 +842,8 @@ static int posix_cpu_timer_set(struct k_itimer *timer, int flags, ...@@ -794,6 +842,8 @@ static int posix_cpu_timer_set(struct k_itimer *timer, int flags,
sample_to_timespec(timer->it_clock, sample_to_timespec(timer->it_clock,
old_incr, &old->it_interval); old_incr, &old->it_interval);
} }
if (!ret)
posix_cpu_timer_kick_nohz();
return ret; return ret;
} }
...@@ -1008,21 +1058,6 @@ static void check_cpu_itimer(struct task_struct *tsk, struct cpu_itimer *it, ...@@ -1008,21 +1058,6 @@ static void check_cpu_itimer(struct task_struct *tsk, struct cpu_itimer *it,
} }
} }
/**
* task_cputime_zero - Check a task_cputime struct for all zero fields.
*
* @cputime: The struct to compare.
*
* Checks @cputime to see if all fields are zero. Returns true if all fields
* are zero, false if any field is nonzero.
*/
static inline int task_cputime_zero(const struct task_cputime *cputime)
{
if (!cputime->utime && !cputime->stime && !cputime->sum_exec_runtime)
return 1;
return 0;
}
/* /*
* Check for any per-thread CPU timers that have fired and move them * Check for any per-thread CPU timers that have fired and move them
* off the tsk->*_timers list onto the firing list. Per-thread timers * off the tsk->*_timers list onto the firing list. Per-thread timers
...@@ -1336,6 +1371,13 @@ void run_posix_cpu_timers(struct task_struct *tsk) ...@@ -1336,6 +1371,13 @@ void run_posix_cpu_timers(struct task_struct *tsk)
cpu_timer_fire(timer); cpu_timer_fire(timer);
spin_unlock(&timer->it_lock); spin_unlock(&timer->it_lock);
} }
/*
* In case some timers were rescheduled after the queue got emptied,
* wake up full dynticks CPUs.
*/
if (tsk->signal->cputimer.running)
posix_cpu_timer_kick_nohz();
} }
/* /*
...@@ -1366,7 +1408,7 @@ void set_process_cpu_timer(struct task_struct *tsk, unsigned int clock_idx, ...@@ -1366,7 +1408,7 @@ void set_process_cpu_timer(struct task_struct *tsk, unsigned int clock_idx,
} }
if (!*newval) if (!*newval)
return; goto out;
*newval += now.cpu; *newval += now.cpu;
} }
...@@ -1384,6 +1426,8 @@ void set_process_cpu_timer(struct task_struct *tsk, unsigned int clock_idx, ...@@ -1384,6 +1426,8 @@ void set_process_cpu_timer(struct task_struct *tsk, unsigned int clock_idx,
tsk->signal->cputime_expires.virt_exp = *newval; tsk->signal->cputime_expires.virt_exp = *newval;
break; break;
} }
out:
posix_cpu_timer_kick_nohz();
} }
static int do_cpu_nanosleep(const clockid_t which_clock, int flags, static int do_cpu_nanosleep(const clockid_t which_clock, int flags,
......
...@@ -799,6 +799,16 @@ static int rcu_implicit_dynticks_qs(struct rcu_data *rdp) ...@@ -799,6 +799,16 @@ static int rcu_implicit_dynticks_qs(struct rcu_data *rdp)
rdp->offline_fqs++; rdp->offline_fqs++;
return 1; return 1;
} }
/*
* There is a possibility that a CPU in adaptive-ticks state
* might run in the kernel with the scheduling-clock tick disabled
* for an extended time period. Invoke rcu_kick_nohz_cpu() to
* force the CPU to restart the scheduling-clock tick in this
* CPU is in this state.
*/
rcu_kick_nohz_cpu(rdp->cpu);
return 0; return 0;
} }
...@@ -1820,7 +1830,7 @@ rcu_send_cbs_to_orphanage(int cpu, struct rcu_state *rsp, ...@@ -1820,7 +1830,7 @@ rcu_send_cbs_to_orphanage(int cpu, struct rcu_state *rsp,
struct rcu_node *rnp, struct rcu_data *rdp) struct rcu_node *rnp, struct rcu_data *rdp)
{ {
/* No-CBs CPUs do not have orphanable callbacks. */ /* No-CBs CPUs do not have orphanable callbacks. */
if (is_nocb_cpu(rdp->cpu)) if (rcu_is_nocb_cpu(rdp->cpu))
return; return;
/* /*
...@@ -2892,10 +2902,10 @@ static void _rcu_barrier(struct rcu_state *rsp) ...@@ -2892,10 +2902,10 @@ static void _rcu_barrier(struct rcu_state *rsp)
* corresponding CPU's preceding callbacks have been invoked. * corresponding CPU's preceding callbacks have been invoked.
*/ */
for_each_possible_cpu(cpu) { for_each_possible_cpu(cpu) {
if (!cpu_online(cpu) && !is_nocb_cpu(cpu)) if (!cpu_online(cpu) && !rcu_is_nocb_cpu(cpu))
continue; continue;
rdp = per_cpu_ptr(rsp->rda, cpu); rdp = per_cpu_ptr(rsp->rda, cpu);
if (is_nocb_cpu(cpu)) { if (rcu_is_nocb_cpu(cpu)) {
_rcu_barrier_trace(rsp, "OnlineNoCB", cpu, _rcu_barrier_trace(rsp, "OnlineNoCB", cpu,
rsp->n_barrier_done); rsp->n_barrier_done);
atomic_inc(&rsp->barrier_cpu_count); atomic_inc(&rsp->barrier_cpu_count);
......
...@@ -530,13 +530,13 @@ static int rcu_nocb_needs_gp(struct rcu_state *rsp); ...@@ -530,13 +530,13 @@ static int rcu_nocb_needs_gp(struct rcu_state *rsp);
static void rcu_nocb_gp_set(struct rcu_node *rnp, int nrq); static void rcu_nocb_gp_set(struct rcu_node *rnp, int nrq);
static void rcu_nocb_gp_cleanup(struct rcu_state *rsp, struct rcu_node *rnp); static void rcu_nocb_gp_cleanup(struct rcu_state *rsp, struct rcu_node *rnp);
static void rcu_init_one_nocb(struct rcu_node *rnp); static void rcu_init_one_nocb(struct rcu_node *rnp);
static bool is_nocb_cpu(int cpu);
static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp, static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp,
bool lazy); bool lazy);
static bool rcu_nocb_adopt_orphan_cbs(struct rcu_state *rsp, static bool rcu_nocb_adopt_orphan_cbs(struct rcu_state *rsp,
struct rcu_data *rdp); struct rcu_data *rdp);
static void rcu_boot_init_nocb_percpu_data(struct rcu_data *rdp); static void rcu_boot_init_nocb_percpu_data(struct rcu_data *rdp);
static void rcu_spawn_nocb_kthreads(struct rcu_state *rsp); static void rcu_spawn_nocb_kthreads(struct rcu_state *rsp);
static void rcu_kick_nohz_cpu(int cpu);
static bool init_nocb_callback_list(struct rcu_data *rdp); static bool init_nocb_callback_list(struct rcu_data *rdp);
#endif /* #ifndef RCU_TREE_NONCORE */ #endif /* #ifndef RCU_TREE_NONCORE */
......
...@@ -28,6 +28,7 @@ ...@@ -28,6 +28,7 @@
#include <linux/gfp.h> #include <linux/gfp.h>
#include <linux/oom.h> #include <linux/oom.h>
#include <linux/smpboot.h> #include <linux/smpboot.h>
#include <linux/tick.h>
#define RCU_KTHREAD_PRIO 1 #define RCU_KTHREAD_PRIO 1
...@@ -1705,7 +1706,7 @@ static void rcu_prepare_for_idle(int cpu) ...@@ -1705,7 +1706,7 @@ static void rcu_prepare_for_idle(int cpu)
return; return;
/* If this is a no-CBs CPU, no callbacks, just return. */ /* If this is a no-CBs CPU, no callbacks, just return. */
if (is_nocb_cpu(cpu)) if (rcu_is_nocb_cpu(cpu))
return; return;
/* /*
...@@ -1747,7 +1748,7 @@ static void rcu_cleanup_after_idle(int cpu) ...@@ -1747,7 +1748,7 @@ static void rcu_cleanup_after_idle(int cpu)
struct rcu_data *rdp; struct rcu_data *rdp;
struct rcu_state *rsp; struct rcu_state *rsp;
if (is_nocb_cpu(cpu)) if (rcu_is_nocb_cpu(cpu))
return; return;
rcu_try_advance_all_cbs(); rcu_try_advance_all_cbs();
for_each_rcu_flavor(rsp) { for_each_rcu_flavor(rsp) {
...@@ -2052,7 +2053,7 @@ static void rcu_init_one_nocb(struct rcu_node *rnp) ...@@ -2052,7 +2053,7 @@ static void rcu_init_one_nocb(struct rcu_node *rnp)
} }
/* Is the specified CPU a no-CPUs CPU? */ /* Is the specified CPU a no-CPUs CPU? */
static bool is_nocb_cpu(int cpu) bool rcu_is_nocb_cpu(int cpu)
{ {
if (have_rcu_nocb_mask) if (have_rcu_nocb_mask)
return cpumask_test_cpu(cpu, rcu_nocb_mask); return cpumask_test_cpu(cpu, rcu_nocb_mask);
...@@ -2110,7 +2111,7 @@ static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp, ...@@ -2110,7 +2111,7 @@ static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp,
bool lazy) bool lazy)
{ {
if (!is_nocb_cpu(rdp->cpu)) if (!rcu_is_nocb_cpu(rdp->cpu))
return 0; return 0;
__call_rcu_nocb_enqueue(rdp, rhp, &rhp->next, 1, lazy); __call_rcu_nocb_enqueue(rdp, rhp, &rhp->next, 1, lazy);
if (__is_kfree_rcu_offset((unsigned long)rhp->func)) if (__is_kfree_rcu_offset((unsigned long)rhp->func))
...@@ -2134,7 +2135,7 @@ static bool __maybe_unused rcu_nocb_adopt_orphan_cbs(struct rcu_state *rsp, ...@@ -2134,7 +2135,7 @@ static bool __maybe_unused rcu_nocb_adopt_orphan_cbs(struct rcu_state *rsp,
long qll = rsp->qlen_lazy; long qll = rsp->qlen_lazy;
/* If this is not a no-CBs CPU, tell the caller to do it the old way. */ /* If this is not a no-CBs CPU, tell the caller to do it the old way. */
if (!is_nocb_cpu(smp_processor_id())) if (!rcu_is_nocb_cpu(smp_processor_id()))
return 0; return 0;
rsp->qlen = 0; rsp->qlen = 0;
rsp->qlen_lazy = 0; rsp->qlen_lazy = 0;
...@@ -2306,11 +2307,6 @@ static void rcu_init_one_nocb(struct rcu_node *rnp) ...@@ -2306,11 +2307,6 @@ static void rcu_init_one_nocb(struct rcu_node *rnp)
{ {
} }
static bool is_nocb_cpu(int cpu)
{
return false;
}
static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp, static bool __call_rcu_nocb(struct rcu_data *rdp, struct rcu_head *rhp,
bool lazy) bool lazy)
{ {
...@@ -2337,3 +2333,20 @@ static bool init_nocb_callback_list(struct rcu_data *rdp) ...@@ -2337,3 +2333,20 @@ static bool init_nocb_callback_list(struct rcu_data *rdp)
} }
#endif /* #else #ifdef CONFIG_RCU_NOCB_CPU */ #endif /* #else #ifdef CONFIG_RCU_NOCB_CPU */
/*
* An adaptive-ticks CPU can potentially execute in kernel mode for an
* arbitrarily long period of time with the scheduling-clock tick turned
* off. RCU will be paying attention to this CPU because it is in the
* kernel, but the CPU cannot be guaranteed to be executing the RCU state
* machine because the scheduling-clock tick has been disabled. Therefore,
* if an adaptive-ticks CPU is failing to respond to the current grace
* period and has not be idle from an RCU perspective, kick it.
*/
static void rcu_kick_nohz_cpu(int cpu)
{
#ifdef CONFIG_NO_HZ_FULL
if (tick_nohz_full_cpu(cpu))
smp_send_reschedule(cpu);
#endif /* #ifdef CONFIG_NO_HZ_FULL */
}
...@@ -544,7 +544,7 @@ void resched_cpu(int cpu) ...@@ -544,7 +544,7 @@ void resched_cpu(int cpu)
raw_spin_unlock_irqrestore(&rq->lock, flags); raw_spin_unlock_irqrestore(&rq->lock, flags);
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* In the semi idle case, use the nearest busy cpu for migrating timers * In the semi idle case, use the nearest busy cpu for migrating timers
* from an idle cpu. This is good for power-savings. * from an idle cpu. This is good for power-savings.
...@@ -582,7 +582,7 @@ int get_nohz_timer_target(void) ...@@ -582,7 +582,7 @@ int get_nohz_timer_target(void)
* account when the CPU goes back to idle and evaluates the timer * account when the CPU goes back to idle and evaluates the timer
* wheel for the next timer event. * wheel for the next timer event.
*/ */
void wake_up_idle_cpu(int cpu) static void wake_up_idle_cpu(int cpu)
{ {
struct rq *rq = cpu_rq(cpu); struct rq *rq = cpu_rq(cpu);
...@@ -612,20 +612,56 @@ void wake_up_idle_cpu(int cpu) ...@@ -612,20 +612,56 @@ void wake_up_idle_cpu(int cpu)
smp_send_reschedule(cpu); smp_send_reschedule(cpu);
} }
static bool wake_up_full_nohz_cpu(int cpu)
{
if (tick_nohz_full_cpu(cpu)) {
if (cpu != smp_processor_id() ||
tick_nohz_tick_stopped())
smp_send_reschedule(cpu);
return true;
}
return false;
}
void wake_up_nohz_cpu(int cpu)
{
if (!wake_up_full_nohz_cpu(cpu))
wake_up_idle_cpu(cpu);
}
static inline bool got_nohz_idle_kick(void) static inline bool got_nohz_idle_kick(void)
{ {
int cpu = smp_processor_id(); int cpu = smp_processor_id();
return idle_cpu(cpu) && test_bit(NOHZ_BALANCE_KICK, nohz_flags(cpu)); return idle_cpu(cpu) && test_bit(NOHZ_BALANCE_KICK, nohz_flags(cpu));
} }
#else /* CONFIG_NO_HZ */ #else /* CONFIG_NO_HZ_COMMON */
static inline bool got_nohz_idle_kick(void) static inline bool got_nohz_idle_kick(void)
{ {
return false; return false;
} }
#endif /* CONFIG_NO_HZ */ #endif /* CONFIG_NO_HZ_COMMON */
#ifdef CONFIG_NO_HZ_FULL
bool sched_can_stop_tick(void)
{
struct rq *rq;
rq = this_rq();
/* Make sure rq->nr_running update is visible after the IPI */
smp_rmb();
/* More than one running task need preemption */
if (rq->nr_running > 1)
return false;
return true;
}
#endif /* CONFIG_NO_HZ_FULL */
void sched_avg_update(struct rq *rq) void sched_avg_update(struct rq *rq)
{ {
...@@ -1357,7 +1393,8 @@ static void sched_ttwu_pending(void) ...@@ -1357,7 +1393,8 @@ static void sched_ttwu_pending(void)
void scheduler_ipi(void) void scheduler_ipi(void)
{ {
if (llist_empty(&this_rq()->wake_list) && !got_nohz_idle_kick()) if (llist_empty(&this_rq()->wake_list) && !got_nohz_idle_kick()
&& !tick_nohz_full_cpu(smp_processor_id()))
return; return;
/* /*
...@@ -1374,6 +1411,7 @@ void scheduler_ipi(void) ...@@ -1374,6 +1411,7 @@ void scheduler_ipi(void)
* somewhat pessimize the simple resched case. * somewhat pessimize the simple resched case.
*/ */
irq_enter(); irq_enter();
tick_nohz_full_check();
sched_ttwu_pending(); sched_ttwu_pending();
/* /*
...@@ -1855,6 +1893,8 @@ static void finish_task_switch(struct rq *rq, struct task_struct *prev) ...@@ -1855,6 +1893,8 @@ static void finish_task_switch(struct rq *rq, struct task_struct *prev)
kprobe_flush_task(prev); kprobe_flush_task(prev);
put_task_struct(prev); put_task_struct(prev);
} }
tick_nohz_task_switch(current);
} }
#ifdef CONFIG_SMP #ifdef CONFIG_SMP
...@@ -2118,7 +2158,7 @@ calc_load(unsigned long load, unsigned long exp, unsigned long active) ...@@ -2118,7 +2158,7 @@ calc_load(unsigned long load, unsigned long exp, unsigned long active)
return load >> FSHIFT; return load >> FSHIFT;
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* Handle NO_HZ for the global load-average. * Handle NO_HZ for the global load-average.
* *
...@@ -2344,12 +2384,12 @@ static void calc_global_nohz(void) ...@@ -2344,12 +2384,12 @@ static void calc_global_nohz(void)
smp_wmb(); smp_wmb();
calc_load_idx++; calc_load_idx++;
} }
#else /* !CONFIG_NO_HZ */ #else /* !CONFIG_NO_HZ_COMMON */
static inline long calc_load_fold_idle(void) { return 0; } static inline long calc_load_fold_idle(void) { return 0; }
static inline void calc_global_nohz(void) { } static inline void calc_global_nohz(void) { }
#endif /* CONFIG_NO_HZ */ #endif /* CONFIG_NO_HZ_COMMON */
/* /*
* calc_load - update the avenrun load estimates 10 ticks after the * calc_load - update the avenrun load estimates 10 ticks after the
...@@ -2509,7 +2549,7 @@ static void __update_cpu_load(struct rq *this_rq, unsigned long this_load, ...@@ -2509,7 +2549,7 @@ static void __update_cpu_load(struct rq *this_rq, unsigned long this_load,
sched_avg_update(this_rq); sched_avg_update(this_rq);
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* There is no sane way to deal with nohz on smp when using jiffies because the * There is no sane way to deal with nohz on smp when using jiffies because the
* cpu doing the jiffies update might drift wrt the cpu doing the jiffy reading * cpu doing the jiffies update might drift wrt the cpu doing the jiffy reading
...@@ -2569,7 +2609,7 @@ void update_cpu_load_nohz(void) ...@@ -2569,7 +2609,7 @@ void update_cpu_load_nohz(void)
} }
raw_spin_unlock(&this_rq->lock); raw_spin_unlock(&this_rq->lock);
} }
#endif /* CONFIG_NO_HZ */ #endif /* CONFIG_NO_HZ_COMMON */
/* /*
* Called from scheduler_tick() * Called from scheduler_tick()
...@@ -2696,7 +2736,34 @@ void scheduler_tick(void) ...@@ -2696,7 +2736,34 @@ void scheduler_tick(void)
rq->idle_balance = idle_cpu(cpu); rq->idle_balance = idle_cpu(cpu);
trigger_load_balance(rq, cpu); trigger_load_balance(rq, cpu);
#endif #endif
rq_last_tick_reset(rq);
}
#ifdef CONFIG_NO_HZ_FULL
/**
* scheduler_tick_max_deferment
*
* Keep at least one tick per second when a single
* active task is running because the scheduler doesn't
* yet completely support full dynticks environment.
*
* This makes sure that uptime, CFS vruntime, load
* balancing, etc... continue to move forward, even
* with a very low granularity.
*/
u64 scheduler_tick_max_deferment(void)
{
struct rq *rq = this_rq();
unsigned long next, now = ACCESS_ONCE(jiffies);
next = rq->last_sched_tick + HZ;
if (time_before_eq(next, now))
return 0;
return jiffies_to_usecs(next - now) * NSEC_PER_USEC;
} }
#endif
notrace unsigned long get_parent_ip(unsigned long addr) notrace unsigned long get_parent_ip(unsigned long addr)
{ {
...@@ -6951,9 +7018,12 @@ void __init sched_init(void) ...@@ -6951,9 +7018,12 @@ void __init sched_init(void)
INIT_LIST_HEAD(&rq->cfs_tasks); INIT_LIST_HEAD(&rq->cfs_tasks);
rq_attach_root(rq, &def_root_domain); rq_attach_root(rq, &def_root_domain);
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
rq->nohz_flags = 0; rq->nohz_flags = 0;
#endif #endif
#ifdef CONFIG_NO_HZ_FULL
rq->last_sched_tick = 0;
#endif
#endif #endif
init_rq_hrtick(rq); init_rq_hrtick(rq);
atomic_set(&rq->nr_iowait, 0); atomic_set(&rq->nr_iowait, 0);
......
...@@ -5355,7 +5355,7 @@ static int active_load_balance_cpu_stop(void *data) ...@@ -5355,7 +5355,7 @@ static int active_load_balance_cpu_stop(void *data)
return 0; return 0;
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* idle load balancing details * idle load balancing details
* - When one of the busy CPUs notice that there may be an idle rebalancing * - When one of the busy CPUs notice that there may be an idle rebalancing
...@@ -5572,9 +5572,9 @@ static void rebalance_domains(int cpu, enum cpu_idle_type idle) ...@@ -5572,9 +5572,9 @@ static void rebalance_domains(int cpu, enum cpu_idle_type idle)
rq->next_balance = next_balance; rq->next_balance = next_balance;
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* In CONFIG_NO_HZ case, the idle balance kickee will do the * In CONFIG_NO_HZ_COMMON case, the idle balance kickee will do the
* rebalancing for all the cpus for whom scheduler ticks are stopped. * rebalancing for all the cpus for whom scheduler ticks are stopped.
*/ */
static void nohz_idle_balance(int this_cpu, enum cpu_idle_type idle) static void nohz_idle_balance(int this_cpu, enum cpu_idle_type idle)
...@@ -5717,7 +5717,7 @@ void trigger_load_balance(struct rq *rq, int cpu) ...@@ -5717,7 +5717,7 @@ void trigger_load_balance(struct rq *rq, int cpu)
if (time_after_eq(jiffies, rq->next_balance) && if (time_after_eq(jiffies, rq->next_balance) &&
likely(!on_null_domain(cpu))) likely(!on_null_domain(cpu)))
raise_softirq(SCHED_SOFTIRQ); raise_softirq(SCHED_SOFTIRQ);
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
if (nohz_kick_needed(rq, cpu) && likely(!on_null_domain(cpu))) if (nohz_kick_needed(rq, cpu) && likely(!on_null_domain(cpu)))
nohz_balancer_kick(cpu); nohz_balancer_kick(cpu);
#endif #endif
...@@ -6187,7 +6187,7 @@ __init void init_sched_fair_class(void) ...@@ -6187,7 +6187,7 @@ __init void init_sched_fair_class(void)
#ifdef CONFIG_SMP #ifdef CONFIG_SMP
open_softirq(SCHED_SOFTIRQ, run_rebalance_domains); open_softirq(SCHED_SOFTIRQ, run_rebalance_domains);
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
nohz.next_balance = jiffies; nohz.next_balance = jiffies;
zalloc_cpumask_var(&nohz.idle_cpus_mask, GFP_NOWAIT); zalloc_cpumask_var(&nohz.idle_cpus_mask, GFP_NOWAIT);
cpu_notifier(sched_ilb_notifier, 0); cpu_notifier(sched_ilb_notifier, 0);
......
...@@ -17,6 +17,7 @@ select_task_rq_idle(struct task_struct *p, int sd_flag, int flags) ...@@ -17,6 +17,7 @@ select_task_rq_idle(struct task_struct *p, int sd_flag, int flags)
static void pre_schedule_idle(struct rq *rq, struct task_struct *prev) static void pre_schedule_idle(struct rq *rq, struct task_struct *prev)
{ {
idle_exit_fair(rq); idle_exit_fair(rq);
rq_last_tick_reset(rq);
} }
static void post_schedule_idle(struct rq *rq) static void post_schedule_idle(struct rq *rq)
......
...@@ -5,6 +5,7 @@ ...@@ -5,6 +5,7 @@
#include <linux/mutex.h> #include <linux/mutex.h>
#include <linux/spinlock.h> #include <linux/spinlock.h>
#include <linux/stop_machine.h> #include <linux/stop_machine.h>
#include <linux/tick.h>
#include "cpupri.h" #include "cpupri.h"
#include "cpuacct.h" #include "cpuacct.h"
...@@ -405,9 +406,12 @@ struct rq { ...@@ -405,9 +406,12 @@ struct rq {
#define CPU_LOAD_IDX_MAX 5 #define CPU_LOAD_IDX_MAX 5
unsigned long cpu_load[CPU_LOAD_IDX_MAX]; unsigned long cpu_load[CPU_LOAD_IDX_MAX];
unsigned long last_load_update_tick; unsigned long last_load_update_tick;
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
u64 nohz_stamp; u64 nohz_stamp;
unsigned long nohz_flags; unsigned long nohz_flags;
#endif
#ifdef CONFIG_NO_HZ_FULL
unsigned long last_sched_tick;
#endif #endif
int skip_clock_update; int skip_clock_update;
...@@ -1072,6 +1076,16 @@ static inline u64 steal_ticks(u64 steal) ...@@ -1072,6 +1076,16 @@ static inline u64 steal_ticks(u64 steal)
static inline void inc_nr_running(struct rq *rq) static inline void inc_nr_running(struct rq *rq)
{ {
rq->nr_running++; rq->nr_running++;
#ifdef CONFIG_NO_HZ_FULL
if (rq->nr_running == 2) {
if (tick_nohz_full_cpu(rq->cpu)) {
/* Order rq->nr_running write against the IPI */
smp_wmb();
smp_send_reschedule(rq->cpu);
}
}
#endif
} }
static inline void dec_nr_running(struct rq *rq) static inline void dec_nr_running(struct rq *rq)
...@@ -1079,6 +1093,13 @@ static inline void dec_nr_running(struct rq *rq) ...@@ -1079,6 +1093,13 @@ static inline void dec_nr_running(struct rq *rq)
rq->nr_running--; rq->nr_running--;
} }
static inline void rq_last_tick_reset(struct rq *rq)
{
#ifdef CONFIG_NO_HZ_FULL
rq->last_sched_tick = jiffies;
#endif
}
extern void update_rq_clock(struct rq *rq); extern void update_rq_clock(struct rq *rq);
extern void activate_task(struct rq *rq, struct task_struct *p, int flags); extern void activate_task(struct rq *rq, struct task_struct *p, int flags);
...@@ -1299,7 +1320,7 @@ extern void init_rt_rq(struct rt_rq *rt_rq, struct rq *rq); ...@@ -1299,7 +1320,7 @@ extern void init_rt_rq(struct rt_rq *rt_rq, struct rq *rq);
extern void account_cfs_bandwidth_used(int enabled, int was_enabled); extern void account_cfs_bandwidth_used(int enabled, int was_enabled);
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
enum rq_nohz_flag_bits { enum rq_nohz_flag_bits {
NOHZ_TICK_STOPPED, NOHZ_TICK_STOPPED,
NOHZ_BALANCE_KICK, NOHZ_BALANCE_KICK,
......
...@@ -329,6 +329,19 @@ static inline void invoke_softirq(void) ...@@ -329,6 +329,19 @@ static inline void invoke_softirq(void)
wakeup_softirqd(); wakeup_softirqd();
} }
static inline void tick_irq_exit(void)
{
#ifdef CONFIG_NO_HZ_COMMON
int cpu = smp_processor_id();
/* Make sure that timer wheel updates are propagated */
if ((idle_cpu(cpu) && !need_resched()) || tick_nohz_full_cpu(cpu)) {
if (!in_interrupt())
tick_nohz_irq_exit();
}
#endif
}
/* /*
* Exit an interrupt context. Process softirqs if needed and possible: * Exit an interrupt context. Process softirqs if needed and possible:
*/ */
...@@ -346,11 +359,7 @@ void irq_exit(void) ...@@ -346,11 +359,7 @@ void irq_exit(void)
if (!in_interrupt() && local_softirq_pending()) if (!in_interrupt() && local_softirq_pending())
invoke_softirq(); invoke_softirq();
#ifdef CONFIG_NO_HZ tick_irq_exit();
/* Make sure that timer wheel updates are propagated */
if (idle_cpu(smp_processor_id()) && !in_interrupt() && !need_resched())
tick_nohz_irq_exit();
#endif
rcu_irq_exit(); rcu_irq_exit();
} }
......
...@@ -64,20 +64,88 @@ config GENERIC_CMOS_UPDATE ...@@ -64,20 +64,88 @@ config GENERIC_CMOS_UPDATE
if GENERIC_CLOCKEVENTS if GENERIC_CLOCKEVENTS
menu "Timers subsystem" menu "Timers subsystem"
# Core internal switch. Selected by NO_HZ / HIGH_RES_TIMERS. This is # Core internal switch. Selected by NO_HZ_COMMON / HIGH_RES_TIMERS. This is
# only related to the tick functionality. Oneshot clockevent devices # only related to the tick functionality. Oneshot clockevent devices
# are supported independ of this. # are supported independ of this.
config TICK_ONESHOT config TICK_ONESHOT
bool bool
config NO_HZ config NO_HZ_COMMON
bool "Tickless System (Dynamic Ticks)" bool
depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
select TICK_ONESHOT select TICK_ONESHOT
choice
prompt "Timer tick handling"
default NO_HZ_IDLE if NO_HZ
config HZ_PERIODIC
bool "Periodic timer ticks (constant rate, no dynticks)"
help
This option keeps the tick running periodically at a constant
rate, even when the CPU doesn't need it.
config NO_HZ_IDLE
bool "Idle dynticks system (tickless idle)"
depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
select NO_HZ_COMMON
help
This option enables a tickless idle system: timer interrupts
will only trigger on an as-needed basis when the system is idle.
This is usually interesting for energy saving.
Most of the time you want to say Y here.
config NO_HZ_FULL
bool "Full dynticks system (tickless)"
# NO_HZ_COMMON dependency
depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
# We need at least one periodic CPU for timekeeping
depends on SMP
# RCU_USER_QS dependency
depends on HAVE_CONTEXT_TRACKING
# VIRT_CPU_ACCOUNTING_GEN dependency
depends on 64BIT
select NO_HZ_COMMON
select RCU_USER_QS
select RCU_NOCB_CPU
select VIRT_CPU_ACCOUNTING_GEN
select CONTEXT_TRACKING_FORCE
select IRQ_WORK
help
Adaptively try to shutdown the tick whenever possible, even when
the CPU is running tasks. Typically this requires running a single
task on the CPU. Chances for running tickless are maximized when
the task mostly runs in userspace and has few kernel activity.
You need to fill up the nohz_full boot parameter with the
desired range of dynticks CPUs.
This is implemented at the expense of some overhead in user <-> kernel
transitions: syscalls, exceptions and interrupts. Even when it's
dynamically off.
Say N.
endchoice
config NO_HZ_FULL_ALL
bool "Full dynticks system on all CPUs by default"
depends on NO_HZ_FULL
help
If the user doesn't pass the nohz_full boot option to
define the range of full dynticks CPUs, consider that all
CPUs in the system are full dynticks by default.
Note the boot CPU will still be kept outside the range to
handle the timekeeping duty.
config NO_HZ
bool "Old Idle dynticks config"
depends on !ARCH_USES_GETTIMEOFFSET && GENERIC_CLOCKEVENTS
help help
This option enables a tickless system: timer interrupts will This is the old config entry that enables dynticks idle.
only trigger on an as-needed basis both when the system is We keep it around for a little while to enforce backward
busy and when the system is idle. compatibility with older config files.
config HIGH_RES_TIMERS config HIGH_RES_TIMERS
bool "High Resolution Timer Support" bool "High Resolution Timer Support"
......
...@@ -693,7 +693,8 @@ void tick_broadcast_setup_oneshot(struct clock_event_device *bc) ...@@ -693,7 +693,8 @@ void tick_broadcast_setup_oneshot(struct clock_event_device *bc)
bc->event_handler = tick_handle_oneshot_broadcast; bc->event_handler = tick_handle_oneshot_broadcast;
/* Take the do_timer update */ /* Take the do_timer update */
tick_do_timer_cpu = cpu; if (!tick_nohz_full_cpu(cpu))
tick_do_timer_cpu = cpu;
/* /*
* We must be careful here. There might be other CPUs * We must be careful here. There might be other CPUs
......
...@@ -163,7 +163,10 @@ static void tick_setup_device(struct tick_device *td, ...@@ -163,7 +163,10 @@ static void tick_setup_device(struct tick_device *td,
* this cpu: * this cpu:
*/ */
if (tick_do_timer_cpu == TICK_DO_TIMER_BOOT) { if (tick_do_timer_cpu == TICK_DO_TIMER_BOOT) {
tick_do_timer_cpu = cpu; if (!tick_nohz_full_cpu(cpu))
tick_do_timer_cpu = cpu;
else
tick_do_timer_cpu = TICK_DO_TIMER_NONE;
tick_next_period = ktime_get(); tick_next_period = ktime_get();
tick_period = ktime_set(0, NSEC_PER_SEC / HZ); tick_period = ktime_set(0, NSEC_PER_SEC / HZ);
} }
......
...@@ -21,11 +21,15 @@ ...@@ -21,11 +21,15 @@
#include <linux/sched.h> #include <linux/sched.h>
#include <linux/module.h> #include <linux/module.h>
#include <linux/irq_work.h> #include <linux/irq_work.h>
#include <linux/posix-timers.h>
#include <linux/perf_event.h>
#include <asm/irq_regs.h> #include <asm/irq_regs.h>
#include "tick-internal.h" #include "tick-internal.h"
#include <trace/events/timer.h>
/* /*
* Per cpu nohz control structure * Per cpu nohz control structure
*/ */
...@@ -104,7 +108,7 @@ static void tick_sched_do_timer(ktime_t now) ...@@ -104,7 +108,7 @@ static void tick_sched_do_timer(ktime_t now)
{ {
int cpu = smp_processor_id(); int cpu = smp_processor_id();
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* Check if the do_timer duty was dropped. We don't care about * Check if the do_timer duty was dropped. We don't care about
* concurrency: This happens only when the cpu in charge went * concurrency: This happens only when the cpu in charge went
...@@ -112,7 +116,8 @@ static void tick_sched_do_timer(ktime_t now) ...@@ -112,7 +116,8 @@ static void tick_sched_do_timer(ktime_t now)
* this duty, then the jiffies update is still serialized by * this duty, then the jiffies update is still serialized by
* jiffies_lock. * jiffies_lock.
*/ */
if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE)) if (unlikely(tick_do_timer_cpu == TICK_DO_TIMER_NONE)
&& !tick_nohz_full_cpu(cpu))
tick_do_timer_cpu = cpu; tick_do_timer_cpu = cpu;
#endif #endif
...@@ -123,7 +128,7 @@ static void tick_sched_do_timer(ktime_t now) ...@@ -123,7 +128,7 @@ static void tick_sched_do_timer(ktime_t now)
static void tick_sched_handle(struct tick_sched *ts, struct pt_regs *regs) static void tick_sched_handle(struct tick_sched *ts, struct pt_regs *regs)
{ {
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* When we are idle and the tick is stopped, we have to touch * When we are idle and the tick is stopped, we have to touch
* the watchdog as we might not schedule for a really long * the watchdog as we might not schedule for a really long
...@@ -142,10 +147,226 @@ static void tick_sched_handle(struct tick_sched *ts, struct pt_regs *regs) ...@@ -142,10 +147,226 @@ static void tick_sched_handle(struct tick_sched *ts, struct pt_regs *regs)
profile_tick(CPU_PROFILING); profile_tick(CPU_PROFILING);
} }
#ifdef CONFIG_NO_HZ_FULL
static cpumask_var_t nohz_full_mask;
bool have_nohz_full_mask;
static bool can_stop_full_tick(void)
{
WARN_ON_ONCE(!irqs_disabled());
if (!sched_can_stop_tick()) {
trace_tick_stop(0, "more than 1 task in runqueue\n");
return false;
}
if (!posix_cpu_timers_can_stop_tick(current)) {
trace_tick_stop(0, "posix timers running\n");
return false;
}
if (!perf_event_can_stop_tick()) {
trace_tick_stop(0, "perf events running\n");
return false;
}
/* sched_clock_tick() needs us? */
#ifdef CONFIG_HAVE_UNSTABLE_SCHED_CLOCK
/*
* TODO: kick full dynticks CPUs when
* sched_clock_stable is set.
*/
if (!sched_clock_stable) {
trace_tick_stop(0, "unstable sched clock\n");
return false;
}
#endif
return true;
}
static void tick_nohz_restart_sched_tick(struct tick_sched *ts, ktime_t now);
/*
* Re-evaluate the need for the tick on the current CPU
* and restart it if necessary.
*/
void tick_nohz_full_check(void)
{
struct tick_sched *ts = &__get_cpu_var(tick_cpu_sched);
if (tick_nohz_full_cpu(smp_processor_id())) {
if (ts->tick_stopped && !is_idle_task(current)) {
if (!can_stop_full_tick())
tick_nohz_restart_sched_tick(ts, ktime_get());
}
}
}
static void nohz_full_kick_work_func(struct irq_work *work)
{
tick_nohz_full_check();
}
static DEFINE_PER_CPU(struct irq_work, nohz_full_kick_work) = {
.func = nohz_full_kick_work_func,
};
/*
* Kick the current CPU if it's full dynticks in order to force it to
* re-evaluate its dependency on the tick and restart it if necessary.
*/
void tick_nohz_full_kick(void)
{
if (tick_nohz_full_cpu(smp_processor_id()))
irq_work_queue(&__get_cpu_var(nohz_full_kick_work));
}
static void nohz_full_kick_ipi(void *info)
{
tick_nohz_full_check();
}
/*
* Kick all full dynticks CPUs in order to force these to re-evaluate
* their dependency on the tick and restart it if necessary.
*/
void tick_nohz_full_kick_all(void)
{
if (!have_nohz_full_mask)
return;
preempt_disable();
smp_call_function_many(nohz_full_mask,
nohz_full_kick_ipi, NULL, false);
preempt_enable();
}
/*
* Re-evaluate the need for the tick as we switch the current task.
* It might need the tick due to per task/process properties:
* perf events, posix cpu timers, ...
*/
void tick_nohz_task_switch(struct task_struct *tsk)
{
unsigned long flags;
local_irq_save(flags);
if (!tick_nohz_full_cpu(smp_processor_id()))
goto out;
if (tick_nohz_tick_stopped() && !can_stop_full_tick())
tick_nohz_full_kick();
out:
local_irq_restore(flags);
}
int tick_nohz_full_cpu(int cpu)
{
if (!have_nohz_full_mask)
return 0;
return cpumask_test_cpu(cpu, nohz_full_mask);
}
/* Parse the boot-time nohz CPU list from the kernel parameters. */
static int __init tick_nohz_full_setup(char *str)
{
int cpu;
alloc_bootmem_cpumask_var(&nohz_full_mask);
if (cpulist_parse(str, nohz_full_mask) < 0) {
pr_warning("NOHZ: Incorrect nohz_full cpumask\n");
return 1;
}
cpu = smp_processor_id();
if (cpumask_test_cpu(cpu, nohz_full_mask)) {
pr_warning("NO_HZ: Clearing %d from nohz_full range for timekeeping\n", cpu);
cpumask_clear_cpu(cpu, nohz_full_mask);
}
have_nohz_full_mask = true;
return 1;
}
__setup("nohz_full=", tick_nohz_full_setup);
static int __cpuinit tick_nohz_cpu_down_callback(struct notifier_block *nfb,
unsigned long action,
void *hcpu)
{
unsigned int cpu = (unsigned long)hcpu;
switch (action & ~CPU_TASKS_FROZEN) {
case CPU_DOWN_PREPARE:
/*
* If we handle the timekeeping duty for full dynticks CPUs,
* we can't safely shutdown that CPU.
*/
if (have_nohz_full_mask && tick_do_timer_cpu == cpu)
return -EINVAL;
break;
}
return NOTIFY_OK;
}
/*
* Worst case string length in chunks of CPU range seems 2 steps
* separations: 0,2,4,6,...
* This is NR_CPUS + sizeof('\0')
*/
static char __initdata nohz_full_buf[NR_CPUS + 1];
static int tick_nohz_init_all(void)
{
int err = -1;
#ifdef CONFIG_NO_HZ_FULL_ALL
if (!alloc_cpumask_var(&nohz_full_mask, GFP_KERNEL)) {
pr_err("NO_HZ: Can't allocate full dynticks cpumask\n");
return err;
}
err = 0;
cpumask_setall(nohz_full_mask);
cpumask_clear_cpu(smp_processor_id(), nohz_full_mask);
have_nohz_full_mask = true;
#endif
return err;
}
void __init tick_nohz_init(void)
{
int cpu;
if (!have_nohz_full_mask) {
if (tick_nohz_init_all() < 0)
return;
}
cpu_notifier(tick_nohz_cpu_down_callback, 0);
/* Make sure full dynticks CPU are also RCU nocbs */
for_each_cpu(cpu, nohz_full_mask) {
if (!rcu_is_nocb_cpu(cpu)) {
pr_warning("NO_HZ: CPU %d is not RCU nocb: "
"cleared from nohz_full range", cpu);
cpumask_clear_cpu(cpu, nohz_full_mask);
}
}
cpulist_scnprintf(nohz_full_buf, sizeof(nohz_full_buf), nohz_full_mask);
pr_info("NO_HZ: Full dynticks CPUs: %s.\n", nohz_full_buf);
}
#else
#define have_nohz_full_mask (0)
#endif
/* /*
* NOHZ - aka dynamic tick functionality * NOHZ - aka dynamic tick functionality
*/ */
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* NO HZ enabled ? * NO HZ enabled ?
*/ */
...@@ -345,11 +566,12 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts, ...@@ -345,11 +566,12 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts,
delta_jiffies = rcu_delta_jiffies; delta_jiffies = rcu_delta_jiffies;
} }
} }
/* /*
* Do not stop the tick, if we are only one off * Do not stop the tick, if we are only one off (or less)
* or if the cpu is required for rcu * or if the cpu is required for RCU:
*/ */
if (!ts->tick_stopped && delta_jiffies == 1) if (!ts->tick_stopped && delta_jiffies <= 1)
goto out; goto out;
/* Schedule the tick, if we are at least one jiffie off */ /* Schedule the tick, if we are at least one jiffie off */
...@@ -378,6 +600,13 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts, ...@@ -378,6 +600,13 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts,
time_delta = KTIME_MAX; time_delta = KTIME_MAX;
} }
#ifdef CONFIG_NO_HZ_FULL
if (!ts->inidle) {
time_delta = min(time_delta,
scheduler_tick_max_deferment());
}
#endif
/* /*
* calculate the expiry time for the next timer wheel * calculate the expiry time for the next timer wheel
* timer. delta_jiffies >= NEXT_TIMER_MAX_DELTA signals * timer. delta_jiffies >= NEXT_TIMER_MAX_DELTA signals
...@@ -421,6 +650,7 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts, ...@@ -421,6 +650,7 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts,
ts->last_tick = hrtimer_get_expires(&ts->sched_timer); ts->last_tick = hrtimer_get_expires(&ts->sched_timer);
ts->tick_stopped = 1; ts->tick_stopped = 1;
trace_tick_stop(1, " ");
} }
/* /*
...@@ -457,6 +687,24 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts, ...@@ -457,6 +687,24 @@ static ktime_t tick_nohz_stop_sched_tick(struct tick_sched *ts,
return ret; return ret;
} }
static void tick_nohz_full_stop_tick(struct tick_sched *ts)
{
#ifdef CONFIG_NO_HZ_FULL
int cpu = smp_processor_id();
if (!tick_nohz_full_cpu(cpu) || is_idle_task(current))
return;
if (!ts->tick_stopped && ts->nohz_mode == NOHZ_MODE_INACTIVE)
return;
if (!can_stop_full_tick())
return;
tick_nohz_stop_sched_tick(ts, ktime_get(), cpu);
#endif
}
static bool can_stop_idle_tick(int cpu, struct tick_sched *ts) static bool can_stop_idle_tick(int cpu, struct tick_sched *ts)
{ {
/* /*
...@@ -489,6 +737,21 @@ static bool can_stop_idle_tick(int cpu, struct tick_sched *ts) ...@@ -489,6 +737,21 @@ static bool can_stop_idle_tick(int cpu, struct tick_sched *ts)
return false; return false;
} }
if (have_nohz_full_mask) {
/*
* Keep the tick alive to guarantee timekeeping progression
* if there are full dynticks CPUs around
*/
if (tick_do_timer_cpu == cpu)
return false;
/*
* Boot safety: make sure the timekeeping duty has been
* assigned before entering dyntick-idle mode,
*/
if (tick_do_timer_cpu == TICK_DO_TIMER_NONE)
return false;
}
return true; return true;
} }
...@@ -568,12 +831,13 @@ void tick_nohz_irq_exit(void) ...@@ -568,12 +831,13 @@ void tick_nohz_irq_exit(void)
{ {
struct tick_sched *ts = &__get_cpu_var(tick_cpu_sched); struct tick_sched *ts = &__get_cpu_var(tick_cpu_sched);
if (!ts->inidle) if (ts->inidle) {
return; /* Cancel the timer because CPU already waken up from the C-states*/
menu_hrtimer_cancel();
/* Cancel the timer because CPU already waken up from the C-states*/ __tick_nohz_idle_enter(ts);
menu_hrtimer_cancel(); } else {
__tick_nohz_idle_enter(ts); tick_nohz_full_stop_tick(ts);
}
} }
/** /**
...@@ -802,7 +1066,7 @@ static inline void tick_check_nohz(int cpu) ...@@ -802,7 +1066,7 @@ static inline void tick_check_nohz(int cpu)
static inline void tick_nohz_switch_to_nohz(void) { } static inline void tick_nohz_switch_to_nohz(void) { }
static inline void tick_check_nohz(int cpu) { } static inline void tick_check_nohz(int cpu) { }
#endif /* NO_HZ */ #endif /* CONFIG_NO_HZ_COMMON */
/* /*
* Called from irq_enter to notify about the possible interruption of idle() * Called from irq_enter to notify about the possible interruption of idle()
...@@ -887,14 +1151,14 @@ void tick_setup_sched_timer(void) ...@@ -887,14 +1151,14 @@ void tick_setup_sched_timer(void)
now = ktime_get(); now = ktime_get();
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
if (tick_nohz_enabled) if (tick_nohz_enabled)
ts->nohz_mode = NOHZ_MODE_HIGHRES; ts->nohz_mode = NOHZ_MODE_HIGHRES;
#endif #endif
} }
#endif /* HIGH_RES_TIMERS */ #endif /* HIGH_RES_TIMERS */
#if defined CONFIG_NO_HZ || defined CONFIG_HIGH_RES_TIMERS #if defined CONFIG_NO_HZ_COMMON || defined CONFIG_HIGH_RES_TIMERS
void tick_cancel_sched_timer(int cpu) void tick_cancel_sched_timer(int cpu)
{ {
struct tick_sched *ts = &per_cpu(tick_cpu_sched, cpu); struct tick_sched *ts = &per_cpu(tick_cpu_sched, cpu);
......
...@@ -739,7 +739,7 @@ __mod_timer(struct timer_list *timer, unsigned long expires, ...@@ -739,7 +739,7 @@ __mod_timer(struct timer_list *timer, unsigned long expires,
cpu = smp_processor_id(); cpu = smp_processor_id();
#if defined(CONFIG_NO_HZ) && defined(CONFIG_SMP) #if defined(CONFIG_NO_HZ_COMMON) && defined(CONFIG_SMP)
if (!pinned && get_sysctl_timer_migration() && idle_cpu(cpu)) if (!pinned && get_sysctl_timer_migration() && idle_cpu(cpu))
cpu = get_nohz_timer_target(); cpu = get_nohz_timer_target();
#endif #endif
...@@ -931,14 +931,14 @@ void add_timer_on(struct timer_list *timer, int cpu) ...@@ -931,14 +931,14 @@ void add_timer_on(struct timer_list *timer, int cpu)
debug_activate(timer, timer->expires); debug_activate(timer, timer->expires);
internal_add_timer(base, timer); internal_add_timer(base, timer);
/* /*
* Check whether the other CPU is idle and needs to be * Check whether the other CPU is in dynticks mode and needs
* triggered to reevaluate the timer wheel when nohz is * to be triggered to reevaluate the timer wheel.
* active. We are protected against the other CPU fiddling * We are protected against the other CPU fiddling
* with the timer by holding the timer base lock. This also * with the timer by holding the timer base lock. This also
* makes sure that a CPU on the way to idle can not evaluate * makes sure that a CPU on the way to stop its tick can not
* the timer wheel. * evaluate the timer wheel.
*/ */
wake_up_idle_cpu(cpu); wake_up_nohz_cpu(cpu);
spin_unlock_irqrestore(&base->lock, flags); spin_unlock_irqrestore(&base->lock, flags);
} }
EXPORT_SYMBOL_GPL(add_timer_on); EXPORT_SYMBOL_GPL(add_timer_on);
...@@ -1189,7 +1189,7 @@ static inline void __run_timers(struct tvec_base *base) ...@@ -1189,7 +1189,7 @@ static inline void __run_timers(struct tvec_base *base)
spin_unlock_irq(&base->lock); spin_unlock_irq(&base->lock);
} }
#ifdef CONFIG_NO_HZ #ifdef CONFIG_NO_HZ_COMMON
/* /*
* Find out when the next timer event is due to happen. This * Find out when the next timer event is due to happen. This
* is used on S/390 to stop all activity when a CPU is idle. * is used on S/390 to stop all activity when a CPU is idle.
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment