sk98lin: remove obsolete driver

All the hardware supported by this driver is now supported
by the skge driver. The last remaining issue was support for ancient
dual port SysKonnect fiber boards, and the skge driver now does these
correctly (p.s. sk98lin was always broken on these old dual port
boards anyway).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>

Documentation/feature-removal-schedule.txt

@@ -213,14 +213,6 @@ Who:  linuxppc-dev@ozlabs.org
 
 ---------------------------
 
-What:   sk98lin network driver
-When:   Feburary 2008
-Why:    In kernel tree version of driver is unmaintained. Sk98lin driver
-	replaced by the skge driver. 
-Who:    Stephen Hemminger <shemminger@linux-foundation.org>
-
----------------------------
-
 What:	i386/x86_64 bzImage symlinks
 When:	April 2008
 
@@ -231,8 +223,6 @@ Who:	Thomas Gleixner <tglx@linutronix.de>
 
 ---------------------------
 
----------------------------
-
 What:	i2c-i810, i2c-prosavage and i2c-savage4
 When:	May 2008
 Why:	These drivers are superseded by i810fb, intelfb and savagefb.

drivers/net/Kconfig

@@ -2220,93 +2220,6 @@ config SKY2_DEBUG
 
 	 If unsure, say N.
 
-config SK98LIN
-	tristate "Marvell Yukon Chipset / SysKonnect SK-98xx Support (DEPRECATED)"
-	depends on PCI
-	---help---
-	  Say Y here if you have a Marvell Yukon or SysKonnect SK-98xx/SK-95xx
-	  compliant Gigabit Ethernet Adapter.
-
-	  This driver supports the original Yukon chipset. This driver is
-	  deprecated and will be removed from the kernel in the near future,
-	  it has been replaced by the skge driver. skge is cleaner and
-	  seems to work better.
-
-	  This driver does not support the newer Yukon2 chipset. A separate
-	  driver, sky2, is provided to support Yukon2-based adapters.
-
-	  The following adapters are supported by this driver:
-	    - 3Com 3C940 Gigabit LOM Ethernet Adapter
-	    - 3Com 3C941 Gigabit LOM Ethernet Adapter
-	    - Allied Telesyn AT-2970LX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970LX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970SX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970SX/2SC Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970TX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2970TX/2TX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2971SX Gigabit Ethernet Adapter
-	    - Allied Telesyn AT-2971T Gigabit Ethernet Adapter
-	    - Belkin Gigabit Desktop Card 10/100/1000Base-T Adapter, Copper RJ-45
-	    - EG1032 v2 Instant Gigabit Network Adapter
-	    - EG1064 v2 Instant Gigabit Network Adapter
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Abit)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Albatron)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Asus)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (ECS)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Epox)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Foxconn)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Gigabyte)
-	    - Marvell 88E8001 Gigabit LOM Ethernet Adapter (Iwill)
-	    - Marvell 88E8050 Gigabit LOM Ethernet Adapter (Intel)
-	    - Marvell RDK-8001 Adapter
-	    - Marvell RDK-8002 Adapter
-	    - Marvell RDK-8003 Adapter
-	    - Marvell RDK-8004 Adapter
-	    - Marvell RDK-8006 Adapter
-	    - Marvell RDK-8007 Adapter
-	    - Marvell RDK-8008 Adapter
-	    - Marvell RDK-8009 Adapter
-	    - Marvell RDK-8010 Adapter
-	    - Marvell RDK-8011 Adapter
-	    - Marvell RDK-8012 Adapter
-	    - Marvell RDK-8052 Adapter
-	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (32 bit)
-	    - Marvell Yukon Gigabit Ethernet 10/100/1000Base-T Adapter (64 bit)
-	    - N-Way PCI-Bus Giga-Card 1000/100/10Mbps(L)
-	    - SK-9521 10/100/1000Base-T Adapter
-	    - SK-9521 V2.0 10/100/1000Base-T Adapter
-	    - SK-9821 Gigabit Ethernet Server Adapter (SK-NET GE-T)
-	    - SK-9821 V2.0 Gigabit Ethernet 10/100/1000Base-T Adapter
-	    - SK-9822 Gigabit Ethernet Server Adapter (SK-NET GE-T dual link)
-	    - SK-9841 Gigabit Ethernet Server Adapter (SK-NET GE-LX)
-	    - SK-9841 V2.0 Gigabit Ethernet 1000Base-LX Adapter
-	    - SK-9842 Gigabit Ethernet Server Adapter (SK-NET GE-LX dual link)
-	    - SK-9843 Gigabit Ethernet Server Adapter (SK-NET GE-SX)
-	    - SK-9843 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9844 Gigabit Ethernet Server Adapter (SK-NET GE-SX dual link)
-	    - SK-9851 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9861 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition)
-	    - SK-9861 V2.0 Gigabit Ethernet 1000Base-SX Adapter
-	    - SK-9862 Gigabit Ethernet Server Adapter (SK-NET GE-SX Volition dual link)
-	    - SK-9871 Gigabit Ethernet Server Adapter (SK-NET GE-ZX)
-	    - SK-9871 V2.0 Gigabit Ethernet 1000Base-ZX Adapter
-	    - SK-9872 Gigabit Ethernet Server Adapter (SK-NET GE-ZX dual link)
-	    - SMC EZ Card 1000 (SMC9452TXV.2)
-	  
-	  The adapters support Jumbo Frames.
-	  The dual link adapters support link-failover and dual port features.
-	  Both Marvell Yukon and SysKonnect SK-98xx/SK-95xx adapters support 
-	  the scatter-gather functionality with sendfile(). Please refer to 
-	  <file:Documentation/networking/sk98lin.txt> for more information about
-	  optional driver parameters.
-	  Questions concerning this driver may be addressed to:
-	      <linux@syskonnect.de>
-	  
-	  If you want to compile this driver as a module ( = code which can be
-	  inserted in and removed from the running kernel whenever you want),
-	  say M here and read <file:Documentation/kbuild/modules.txt>. The module will
-	  be called sk98lin. This is recommended.
-
 config VIA_VELOCITY
 	tristate "VIA Velocity support"
 	depends on PCI

drivers/net/Makefile

@@ -75,7 +75,6 @@ ps3_gelic-objs += ps3_gelic_net.o $(gelic_wireless-y)
 obj-$(CONFIG_TC35815) += tc35815.o
 obj-$(CONFIG_SKGE) += skge.o
 obj-$(CONFIG_SKY2) += sky2.o
-obj-$(CONFIG_SK98LIN) += sk98lin/
 obj-$(CONFIG_SKFP) += skfp/
 obj-$(CONFIG_VIA_RHINE) += via-rhine.o
 obj-$(CONFIG_VIA_VELOCITY) += via-velocity.o

drivers/net/sk98lin/Makefile

-#
-# Makefile for the SysKonnect SK-98xx device driver.
-#
-
-
-#
-# Standalone driver params
-# SKPARAM += -DSK_KERNEL_24
-# SKPARAM += -DSK_KERNEL_24_26
-# SKPARAM += -DSK_KERNEL_26
-# SKPARAM += -DSK_KERNEL_22_24
-
-obj-$(CONFIG_SK98LIN) += sk98lin.o
-sk98lin-objs    :=	\
-		skge.o		\
-		skethtool.o	\
-		skdim.o		\
-		skaddr.o	\
-		skgehwt.o	\
-		skgeinit.o	\
-		skgepnmi.o	\
-		skgesirq.o	\
-		ski2c.o		\
-		sklm80.o	\
-		skqueue.o	\
-		skrlmt.o	\
-		sktimer.o	\
-		skvpd.o		\
-		skxmac2.o
-
-# DBGDEF =  \
-# -DDEBUG
-
-ifdef DEBUG
-DBGDEF +=  \
--DSK_DEBUG_CHKMOD=0x00000000L \
--DSK_DEBUG_CHKCAT=0x00000000L
-endif
-
-
-# **** possible debug modules for SK_DEBUG_CHKMOD *****************
-# SK_DBGMOD_MERR        0x00000001L     /* general module error indication */
-# SK_DBGMOD_HWM         0x00000002L     /* Hardware init module */
-# SK_DBGMOD_RLMT        0x00000004L     /* RLMT module */
-# SK_DBGMOD_VPD         0x00000008L     /* VPD module */
-# SK_DBGMOD_I2C         0x00000010L     /* I2C module */
-# SK_DBGMOD_PNMI        0x00000020L     /* PNMI module */
-# SK_DBGMOD_CSUM        0x00000040L     /* CSUM module */
-# SK_DBGMOD_ADDR        0x00000080L     /* ADDR module */
-# SK_DBGMOD_DRV         0x00010000L     /* DRV module */
-
-# **** possible debug categories for SK_DEBUG_CHKCAT **************
-# *** common modules ***
-# SK_DBGCAT_INIT        0x00000001L     module/driver initialization
-# SK_DBGCAT_CTRL        0x00000002L     controlling: add/rmv MCA/MAC and other controls (IOCTL)
-# SK_DBGCAT_ERR         0x00000004L     error handling paths
-# SK_DBGCAT_TX          0x00000008L     transmit path
-# SK_DBGCAT_RX          0x00000010L     receive path
-# SK_DBGCAT_IRQ         0x00000020L     general IRQ handling
-# SK_DBGCAT_QUEUE       0x00000040L     any queue management
-# SK_DBGCAT_DUMP        0x00000080L     large data output e.g. hex dump
-# SK_DBGCAT_FATAL       0x00000100L     large data output e.g. hex dump
-
-# *** driver (file skge.c) ***
-# SK_DBGCAT_DRV_ENTRY           0x00010000      entry points
-# SK_DBGCAT_DRV_???             0x00020000      not used
-# SK_DBGCAT_DRV_MCA             0x00040000      multicast
-# SK_DBGCAT_DRV_TX_PROGRESS     0x00080000      tx path
-# SK_DBGCAT_DRV_RX_PROGRESS     0x00100000      rx path
-# SK_DBGCAT_DRV_PROGRESS        0x00200000      general runtime
-# SK_DBGCAT_DRV_???             0x00400000      not used
-# SK_DBGCAT_DRV_PROM            0x00800000      promiscuous mode
-# SK_DBGCAT_DRV_TX_FRAME        0x01000000      display tx frames
-# SK_DBGCAT_DRV_ERROR           0x02000000      error conditions
-# SK_DBGCAT_DRV_INT_SRC         0x04000000      interrupts sources
-# SK_DBGCAT_DRV_EVENT           0x08000000      driver events
-
-EXTRA_CFLAGS += -Idrivers/net/sk98lin -DSK_DIAG_SUPPORT -DGENESIS -DYUKON $(DBGDEF) $(SKPARAM)
-
-clean:
-	rm -f core *.o *.a *.s
-
-
-
-
-
-

drivers/net/sk98lin/h/lm80.h

-/******************************************************************************
- *
- * Name:	lm80.h	
- * Project:	Gigabit Ethernet Adapters, Common Modules
- * Version:	$Revision: 1.6 $
- * Date:	$Date: 2003/05/13 17:26:52 $
- * Purpose:	Contains all defines for the LM80 Chip
- *		(National Semiconductor).
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-#ifndef __INC_LM80_H
-#define __INC_LM80_H
-
-#ifdef __cplusplus
-extern "C" {
-#endif	/* __cplusplus */
-
-/* defines ********************************************************************/
-
-/*
- * LM80 register definition
- *
- * All registers are 8 bit wide
- */
-#define LM80_CFG			0x00	/* Configuration Register */
-#define LM80_ISRC_1			0x01	/* Interrupt Status Register 1 */
-#define LM80_ISRC_2			0x02	/* Interrupt Status Register 2 */
-#define LM80_IMSK_1			0x03	/* Interrupt Mask Register 1 */
-#define LM80_IMSK_2			0x04	/* Interrupt Mask Register 2 */
-#define LM80_FAN_CTRL		0x05	/* Fan Devisor/RST#/OS# Register */
-#define LM80_TEMP_CTRL		0x06	/* OS# Config, Temp Res. Reg */
-	/* 0x07 - 0x1f reserved	*/
-	/* current values */
-#define LM80_VT0_IN			0x20	/* current Voltage 0 value */
-#define LM80_VT1_IN			0x21	/* current Voltage 1 value */
-#define LM80_VT2_IN			0x22	/* current Voltage 2 value */
-#define LM80_VT3_IN			0x23	/* current Voltage 3 value */
-#define LM80_VT4_IN			0x24	/* current Voltage 4 value */
-#define LM80_VT5_IN			0x25	/* current Voltage 5 value */
-#define LM80_VT6_IN			0x26	/* current Voltage 6 value */
-#define LM80_TEMP_IN		0x27	/* current Temperature value */
-#define LM80_FAN1_IN		0x28	/* current Fan 1 count */
-#define LM80_FAN2_IN		0x29	/* current Fan 2 count */
-	/* limit values */
-#define LM80_VT0_HIGH_LIM	0x2a	/* high limit val for Voltage 0 */
-#define LM80_VT0_LOW_LIM	0x2b	/* low limit val for Voltage 0 */
-#define LM80_VT1_HIGH_LIM	0x2c	/* high limit val for Voltage 1 */
-#define LM80_VT1_LOW_LIM	0x2d	/* low limit val for Voltage 1 */
-#define LM80_VT2_HIGH_LIM	0x2e	/* high limit val for Voltage 2 */
-#define LM80_VT2_LOW_LIM	0x2f	/* low limit val for Voltage 2 */
-#define LM80_VT3_HIGH_LIM	0x30	/* high limit val for Voltage 3 */
-#define LM80_VT3_LOW_LIM	0x31	/* low limit val for Voltage 3 */
-#define LM80_VT4_HIGH_LIM	0x32	/* high limit val for Voltage 4 */
-#define LM80_VT4_LOW_LIM	0x33	/* low limit val for Voltage 4 */
-#define LM80_VT5_HIGH_LIM	0x34	/* high limit val for Voltage 5 */
-#define LM80_VT5_LOW_LIM	0x35	/* low limit val for Voltage 5 */
-#define LM80_VT6_HIGH_LIM	0x36	/* high limit val for Voltage 6 */
-#define LM80_VT6_LOW_LIM	0x37	/* low limit val for Voltage 6 */
-#define LM80_THOT_LIM_UP	0x38	/* hot temperature limit (high) */
-#define LM80_THOT_LIM_LO	0x39	/* hot temperature limit (low) */
-#define LM80_TOS_LIM_UP		0x3a	/* OS temperature limit (high) */
-#define LM80_TOS_LIM_LO		0x3b	/* OS temperature limit (low) */
-#define LM80_FAN1_COUNT_LIM	0x3c	/* Fan 1 count limit (high) */
-#define LM80_FAN2_COUNT_LIM	0x3d	/* Fan 2 count limit (low) */
-	/* 0x3e - 0x3f reserved	*/
-
-/*
- * LM80 bit definitions
- */
-
-/*	LM80_CFG		Configuration Register */
-#define LM80_CFG_START		(1<<0)	/* start monitoring operation */
-#define LM80_CFG_INT_ENA	(1<<1)	/* enables the INT# Interrupt output */
-#define LM80_CFG_INT_POL	(1<<2)	/* INT# pol: 0 act low, 1 act high */
-#define LM80_CFG_INT_CLR	(1<<3)	/* disables INT#/RST_OUT#/OS# outputs */
-#define LM80_CFG_RESET		(1<<4)	/* signals a reset */
-#define LM80_CFG_CHASS_CLR	(1<<5)	/* clears Chassis Intrusion (CI) pin */
-#define LM80_CFG_GPO		(1<<6)	/* drives the GPO# pin */
-#define LM80_CFG_INIT		(1<<7)	/* restore power on defaults */
-
-/*	LM80_ISRC_1		Interrupt Status Register 1 */
-/*	LM80_IMSK_1		Interrupt Mask Register 1 */
-#define LM80_IS_VT0			(1<<0)	/* limit exceeded for Voltage 0 */
-#define LM80_IS_VT1			(1<<1)	/* limit exceeded for Voltage 1 */
-#define LM80_IS_VT2			(1<<2)	/* limit exceeded for Voltage 2 */
-#define LM80_IS_VT3			(1<<3)	/* limit exceeded for Voltage 3 */
-#define LM80_IS_VT4			(1<<4)	/* limit exceeded for Voltage 4 */
-#define LM80_IS_VT5			(1<<5)	/* limit exceeded for Voltage 5 */
-#define LM80_IS_VT6			(1<<6)	/* limit exceeded for Voltage 6 */
-#define LM80_IS_INT_IN		(1<<7)	/* state of INT_IN# */
-
-/*	LM80_ISRC_2		Interrupt Status Register 2 */
-/*	LM80_IMSK_2		Interrupt Mask Register 2 */
-#define LM80_IS_TEMP		(1<<0)	/* HOT temperature limit exceeded */
-#define LM80_IS_BTI			(1<<1)	/* state of BTI# pin */
-#define LM80_IS_FAN1		(1<<2)	/* count limit exceeded for Fan 1 */
-#define LM80_IS_FAN2		(1<<3)	/* count limit exceeded for Fan 2 */
-#define LM80_IS_CI			(1<<4)	/* Chassis Intrusion occured */
-#define LM80_IS_OS			(1<<5)	/* OS temperature limit exceeded */
-	/* bit 6 and 7 are reserved in LM80_ISRC_2 */
-#define LM80_IS_HT_IRQ_MD	(1<<6)	/* Hot temperature interrupt mode */
-#define LM80_IS_OT_IRQ_MD	(1<<7)	/* OS temperature interrupt mode */
-
-/*	LM80_FAN_CTRL		Fan Devisor/RST#/OS# Register */
-#define LM80_FAN1_MD_SEL	(1<<0)	/* Fan 1 mode select */
-#define LM80_FAN2_MD_SEL	(1<<1)	/* Fan 2 mode select */
-#define LM80_FAN1_PRM_CTL	(3<<2)	/* Fan 1 speed control */
-#define LM80_FAN2_PRM_CTL	(3<<4)	/* Fan 2 speed control */
-#define LM80_FAN_OS_ENA		(1<<6)	/* enable OS mode on RST_OUT#/OS# pins*/
-#define LM80_FAN_RST_ENA	(1<<7)	/* sets RST_OUT#/OS# pins in RST mode */
-
-/*	LM80_TEMP_CTRL		OS# Config, Temp Res. Reg */
-#define LM80_TEMP_OS_STAT	(1<<0)	/* mirrors the state of RST_OUT#/OS# */
-#define LM80_TEMP_OS_POL	(1<<1)	/* select OS# polarity */
-#define LM80_TEMP_OS_MODE	(1<<2)	/* selects Interrupt mode */
-#define LM80_TEMP_RES		(1<<3)	/* selects 9 or 11 bit temp resulution*/
-#define LM80_TEMP_LSB		(0xf<<4)/* 4 LSBs of 11 bit temp data */
-#define LM80_TEMP_LSB_9		(1<<7)	/* LSB of 9 bit temperature data */
-
-	/* 0x07 - 0x1f reserved	*/
-/*	LM80_VT0_IN		current Voltage 0 value */
-/*	LM80_VT1_IN		current Voltage 1 value */
-/*	LM80_VT2_IN		current Voltage 2 value */
-/*	LM80_VT3_IN		current Voltage 3 value */
-/*	LM80_VT4_IN		current Voltage 4 value */
-/*	LM80_VT5_IN		current Voltage 5 value */
-/*	LM80_VT6_IN		current Voltage 6 value */
-/*	LM80_TEMP_IN		current temperature value */
-/*	LM80_FAN1_IN		current Fan 1 count */
-/*	LM80_FAN2_IN		current Fan 2 count */
-/*	LM80_VT0_HIGH_LIM	high limit val for Voltage 0 */
-/*	LM80_VT0_LOW_LIM	low limit val for Voltage 0 */
-/*	LM80_VT1_HIGH_LIM	high limit val for Voltage 1 */
-/*	LM80_VT1_LOW_LIM	low limit val for Voltage 1 */
-/*	LM80_VT2_HIGH_LIM	high limit val for Voltage 2 */
-/*	LM80_VT2_LOW_LIM	low limit val for Voltage 2 */
-/*	LM80_VT3_HIGH_LIM	high limit val for Voltage 3 */
-/*	LM80_VT3_LOW_LIM	low limit val for Voltage 3 */
-/*	LM80_VT4_HIGH_LIM	high limit val for Voltage 4 */
-/*	LM80_VT4_LOW_LIM	low limit val for Voltage 4 */
-/*	LM80_VT5_HIGH_LIM	high limit val for Voltage 5 */
-/*	LM80_VT5_LOW_LIM	low limit val for Voltage 5 */
-/*	LM80_VT6_HIGH_LIM	high limit val for Voltage 6 */
-/*	LM80_VT6_LOW_LIM	low limit val for Voltage 6 */
-/*	LM80_THOT_LIM_UP	hot temperature limit (high) */
-/*	LM80_THOT_LIM_LO	hot temperature limit (low) */
-/*	LM80_TOS_LIM_UP		OS temperature limit (high) */
-/*	LM80_TOS_LIM_LO		OS temperature limit (low) */
-/*	LM80_FAN1_COUNT_LIM	Fan 1 count limit (high) */
-/*	LM80_FAN2_COUNT_LIM	Fan 2 count limit (low) */
-	/* 0x3e - 0x3f reserved	*/
-
-#define LM80_ADDR		0x28	/* LM80 default addr */
-
-/* typedefs *******************************************************************/
-
-
-/* function prototypes ********************************************************/
-
-#ifdef __cplusplus
-}
-#endif	/* __cplusplus */
-
-#endif	/* __INC_LM80_H */

drivers/net/sk98lin/h/skaddr.h

-/******************************************************************************
- *
- * Name:	skaddr.h
- * Project:	Gigabit Ethernet Adapters, ADDR-Modul
- * Version:	$Revision: 1.29 $
- * Date:	$Date: 2003/05/13 16:57:24 $
- * Purpose:	Header file for Address Management (MC, UC, Prom).
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect GmbH.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- * Description:
- *
- * This module is intended to manage multicast addresses and promiscuous mode
- * on GEnesis adapters.
- *
- * Include File Hierarchy:
- *
- *	"skdrv1st.h"
- *	...
- *	"sktypes.h"
- *	"skqueue.h"
- *	"skaddr.h"
- *	...
- *	"skdrv2nd.h"
- *
- ******************************************************************************/
-
-#ifndef __INC_SKADDR_H
-#define __INC_SKADDR_H
-
-#ifdef __cplusplus
-extern "C" {
-#endif	/* cplusplus */
-
-/* defines ********************************************************************/
-
-#define SK_MAC_ADDR_LEN				6	/* Length of MAC address. */
-#define	SK_MAX_ADDRS				14	/* #Addrs for exact match. */
-
-/* ----- Common return values ----- */
-
-#define SK_ADDR_SUCCESS				0	/* Function returned successfully. */
-#define SK_ADDR_ILLEGAL_PORT			100	/* Port number too high. */
-#define SK_ADDR_TOO_EARLY			101	/* Function called too early. */
-
-/* ----- Clear/Add flag bits ----- */
-
-#define SK_ADDR_PERMANENT			1	/* RLMT Address */
-
-/* ----- Additional Clear flag bits ----- */
-
-#define SK_MC_SW_ONLY				2	/* Do not update HW when clearing. */
-
-/* ----- Override flag bits ----- */
-
-#define SK_ADDR_LOGICAL_ADDRESS		0
-#define SK_ADDR_VIRTUAL_ADDRESS		(SK_ADDR_LOGICAL_ADDRESS)	/* old */
-#define SK_ADDR_PHYSICAL_ADDRESS	1
-#define SK_ADDR_CLEAR_LOGICAL		2
-#define SK_ADDR_SET_LOGICAL			4
-
-/* ----- Override return values ----- */
-
-#define SK_ADDR_OVERRIDE_SUCCESS	(SK_ADDR_SUCCESS)
-#define SK_ADDR_DUPLICATE_ADDRESS	1
-#define SK_ADDR_MULTICAST_ADDRESS	2
-
-/* ----- Partitioning of excact match table ----- */
-
-#define SK_ADDR_EXACT_MATCHES		16	/* #Exact match entries. */
-
-#define SK_ADDR_FIRST_MATCH_RLMT	1
-#define SK_ADDR_LAST_MATCH_RLMT		2
-#define SK_ADDR_FIRST_MATCH_DRV		3
-#define SK_ADDR_LAST_MATCH_DRV		(SK_ADDR_EXACT_MATCHES - 1)
-
-/* ----- SkAddrMcAdd/SkAddrMcUpdate return values ----- */
-
-#define SK_MC_FILTERING_EXACT		0	/* Exact filtering. */
-#define SK_MC_FILTERING_INEXACT		1	/* Inexact filtering. */
-
-/* ----- Additional SkAddrMcAdd return values ----- */
-
-#define SK_MC_ILLEGAL_ADDRESS		2	/* Illegal address. */
-#define SK_MC_ILLEGAL_PORT			3	/* Illegal port (not the active one). */
-#define SK_MC_RLMT_OVERFLOW			4	/* Too many RLMT mc addresses. */
-
-/* Promiscuous mode bits ----- */
-
-#define SK_PROM_MODE_NONE			0	/* Normal receive. */
-#define SK_PROM_MODE_LLC			1	/* Receive all LLC frames. */
-#define SK_PROM_MODE_ALL_MC			2	/* Receive all multicast frames. */
-/* #define SK_PROM_MODE_NON_LLC		4 */	/* Receive all non-LLC frames. */
-
-/* Macros */
-
-#ifdef OLD_STUFF
-#ifndef SK_ADDR_EQUAL
-/*
- * "&" instead of "&&" allows better optimization on IA-64.
- * The replacement is safe here, as all bytes exist.
- */
-#ifndef SK_ADDR_DWORD_COMPARE
-#define SK_ADDR_EQUAL(A1,A2)	( \
-	(((SK_U8 *)(A1))[5] == ((SK_U8 *)(A2))[5]) & \
-	(((SK_U8 *)(A1))[4] == ((SK_U8 *)(A2))[4]) & \
-	(((SK_U8 *)(A1))[3] == ((SK_U8 *)(A2))[3]) & \
-	(((SK_U8 *)(A1))[2] == ((SK_U8 *)(A2))[2]) & \
-	(((SK_U8 *)(A1))[1] == ((SK_U8 *)(A2))[1]) & \
-	(((SK_U8 *)(A1))[0] == ((SK_U8 *)(A2))[0]))
-#else	/* SK_ADDR_DWORD_COMPARE */
-#define SK_ADDR_EQUAL(A1,A2)	( \
-	(*(SK_U32 *)&(((SK_U8 *)(A1))[2]) == *(SK_U32 *)&(((SK_U8 *)(A2))[2])) & \
-	(*(SK_U32 *)&(((SK_U8 *)(A1))[0]) == *(SK_U32 *)&(((SK_U8 *)(A2))[0])))
-#endif	/* SK_ADDR_DWORD_COMPARE */
-#endif	/* SK_ADDR_EQUAL */
-#endif /* 0 */
-
-#ifndef SK_ADDR_EQUAL
-#ifndef SK_ADDR_DWORD_COMPARE
-#define SK_ADDR_EQUAL(A1,A2)	( \
-	(((SK_U8 SK_FAR *)(A1))[5] == ((SK_U8 SK_FAR *)(A2))[5]) & \
-	(((SK_U8 SK_FAR *)(A1))[4] == ((SK_U8 SK_FAR *)(A2))[4]) & \
-	(((SK_U8 SK_FAR *)(A1))[3] == ((SK_U8 SK_FAR *)(A2))[3]) & \
-	(((SK_U8 SK_FAR *)(A1))[2] == ((SK_U8 SK_FAR *)(A2))[2]) & \
-	(((SK_U8 SK_FAR *)(A1))[1] == ((SK_U8 SK_FAR *)(A2))[1]) & \
-	(((SK_U8 SK_FAR *)(A1))[0] == ((SK_U8 SK_FAR *)(A2))[0]))
-#else	/* SK_ADDR_DWORD_COMPARE */
-#define SK_ADDR_EQUAL(A1,A2)	( \
-	(*(SK_U16 SK_FAR *)&(((SK_U8 SK_FAR *)(A1))[4]) == \
-	*(SK_U16 SK_FAR *)&(((SK_U8 SK_FAR *)(A2))[4])) && \
-	(*(SK_U32 SK_FAR *)&(((SK_U8 SK_FAR *)(A1))[0]) == \
-	*(SK_U32 SK_FAR *)&(((SK_U8 SK_FAR *)(A2))[0])))
-#endif	/* SK_ADDR_DWORD_COMPARE */
-#endif	/* SK_ADDR_EQUAL */
-
-/* typedefs *******************************************************************/
-
-typedef struct s_MacAddr {
-	SK_U8	a[SK_MAC_ADDR_LEN];
-} SK_MAC_ADDR;
-
-
-/* SK_FILTER is used to ensure alignment of the filter. */
-typedef union s_InexactFilter {
-	SK_U8	Bytes[8];
-	SK_U64	Val;	/* Dummy entry for alignment only. */
-} SK_FILTER64;
-
-
-typedef struct s_AddrNet SK_ADDR_NET;
-
-
-typedef struct s_AddrPort {
-
-/* ----- Public part (read-only) ----- */
-
-	SK_MAC_ADDR	CurrentMacAddress;	/* Current physical MAC Address. */
-	SK_MAC_ADDR	PermanentMacAddress;	/* Permanent physical MAC Address. */
-	int		PromMode;		/* Promiscuous Mode. */
-
-/* ----- Private part ----- */
-
-	SK_MAC_ADDR	PreviousMacAddress;	/* Prev. phys. MAC Address. */
-	SK_BOOL		CurrentMacAddressSet;	/* CurrentMacAddress is set. */
-	SK_U8		Align01;
-
-	SK_U32		FirstExactMatchRlmt;
-	SK_U32		NextExactMatchRlmt;
-	SK_U32		FirstExactMatchDrv;
-	SK_U32		NextExactMatchDrv;
-	SK_MAC_ADDR	Exact[SK_ADDR_EXACT_MATCHES];
-	SK_FILTER64	InexactFilter;			/* For 64-bit hash register. */
-	SK_FILTER64	InexactRlmtFilter;		/* For 64-bit hash register. */
-	SK_FILTER64	InexactDrvFilter;		/* For 64-bit hash register. */
-} SK_ADDR_PORT;
-
-
-struct s_AddrNet {
-/* ----- Public part (read-only) ----- */
-
-	SK_MAC_ADDR		CurrentMacAddress;	/* Logical MAC Address. */
-	SK_MAC_ADDR		PermanentMacAddress;	/* Logical MAC Address. */
-
-/* ----- Private part ----- */
-
-	SK_U32			ActivePort;		/* View of module ADDR. */
-	SK_BOOL			CurrentMacAddressSet;	/* CurrentMacAddress is set. */
-	SK_U8			Align01;
-	SK_U16			Align02;
-};
-
-
-typedef struct s_Addr {
-
-/* ----- Public part (read-only) ----- */
-
-	SK_ADDR_NET		Net[SK_MAX_NETS];
-	SK_ADDR_PORT	Port[SK_MAX_MACS];
-
-/* ----- Private part ----- */
-} SK_ADDR;
-
-/* function prototypes ********************************************************/
-
-#ifndef SK_KR_PROTO
-
-/* Functions provided by SkAddr */
-
-/* ANSI/C++ compliant function prototypes */
-
-extern	int	SkAddrInit(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	int	Level);
-
-extern	int	SkAddrMcClear(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	Flags);
-
-extern	int	SkAddrMcAdd(
-	SK_AC		*pAC,
-	SK_IOC		IoC,
-	SK_U32		PortNumber,
-	SK_MAC_ADDR	*pMc,
-	int		Flags);
-
-extern	int	SkAddrMcUpdate(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber);
-
-extern	int	SkAddrOverride(
-	SK_AC		*pAC,
-	SK_IOC		IoC,
-	SK_U32		PortNumber,
-	SK_MAC_ADDR	SK_FAR *pNewAddr,
-	int		Flags);
-
-extern	int	SkAddrPromiscuousChange(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	PortNumber,
-	int	NewPromMode);
-
-#ifndef SK_SLIM
-extern	int	SkAddrSwap(
-	SK_AC	*pAC,
-	SK_IOC	IoC,
-	SK_U32	FromPortNumber,
-	SK_U32	ToPortNumber);
-#endif
-
-#else	/* defined(SK_KR_PROTO)) */
-
-/* Non-ANSI/C++ compliant function prototypes */
-
-#error KR-style prototypes are not yet provided.
-
-#endif	/* defined(SK_KR_PROTO)) */
-
-
-#ifdef __cplusplus
-}
-#endif	/* __cplusplus */
-
-#endif	/* __INC_SKADDR_H */

drivers/net/sk98lin/h/skcsum.h

-/******************************************************************************
- *
- * Name:	skcsum.h
- * Project:	GEnesis - SysKonnect SK-NET Gigabit Ethernet (SK-98xx)
- * Version:	$Revision: 1.10 $
- * Date:	$Date: 2003/08/20 13:59:57 $
- * Purpose:	Store/verify Internet checksum in send/receive packets.
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2001 SysKonnect GmbH.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- * Description:
- *
- * Public header file for the "GEnesis" common module "CSUM".
- *
- * "GEnesis" is an abbreviation of "Gigabit Ethernet Network System in Silicon"
- * and is the code name of this SysKonnect project.
- *
- * Compilation Options:
- *
- *	SK_USE_CSUM - Define if CSUM is to be used. Otherwise, CSUM will be an
- *	empty module.
- *
- *	SKCS_OVERWRITE_PROTO - Define to overwrite the default protocol id
- *	definitions. In this case, all SKCS_PROTO_xxx definitions must be made
- *	external.
- *
- *	SKCS_OVERWRITE_STATUS - Define to overwrite the default return status
- *	definitions. In this case, all SKCS_STATUS_xxx definitions must be made
- *	external.
- *
- * Include File Hierarchy:
- *
- *	"h/skcsum.h"
- *	 "h/sktypes.h"
- *	 "h/skqueue.h"
- *
- ******************************************************************************/
-
-#ifndef __INC_SKCSUM_H
-#define __INC_SKCSUM_H
-
-#include "h/sktypes.h"
-#include "h/skqueue.h"
-
-/* defines ********************************************************************/
-
-/*
- * Define the default bit flags for 'SKCS_PACKET_INFO.ProtocolFlags'  if no user
- * overwrite.
- */
-#ifndef SKCS_OVERWRITE_PROTO	/* User overwrite? */
-#define SKCS_PROTO_IP	0x1	/* IP (Internet Protocol version 4) */
-#define SKCS_PROTO_TCP	0x2	/* TCP (Transmission Control Protocol) */
-#define SKCS_PROTO_UDP	0x4	/* UDP (User Datagram Protocol) */
-
-/* Indices for protocol statistics. */
-#define SKCS_PROTO_STATS_IP	0
-#define SKCS_PROTO_STATS_UDP	1
-#define SKCS_PROTO_STATS_TCP	2
-#define SKCS_NUM_PROTOCOLS	3	/* Number of supported protocols. */
-#endif	/* !SKCS_OVERWRITE_PROTO */
-
-/*
- * Define the default SKCS_STATUS type and values if no user overwrite.
- *
- *	SKCS_STATUS_UNKNOWN_IP_VERSION - Not an IP v4 frame.
- *	SKCS_STATUS_IP_CSUM_ERROR - IP checksum error.
- *	SKCS_STATUS_IP_CSUM_ERROR_TCP - IP checksum error in TCP frame.
- *	SKCS_STATUS_IP_CSUM_ERROR_UDP - IP checksum error in UDP frame
- *	SKCS_STATUS_IP_FRAGMENT - IP fragment (IP checksum ok).
- *	SKCS_STATUS_IP_CSUM_OK - IP checksum ok (not a TCP or UDP frame).
- *	SKCS_STATUS_TCP_CSUM_ERROR - TCP checksum error (IP checksum ok).
- *	SKCS_STATUS_UDP_CSUM_ERROR - UDP checksum error (IP checksum ok).
- *	SKCS_STATUS_TCP_CSUM_OK - IP and TCP checksum ok.
- *	SKCS_STATUS_UDP_CSUM_OK - IP and UDP checksum ok.
- *	SKCS_STATUS_IP_CSUM_OK_NO_UDP - IP checksum OK and no UDP checksum. 
- */
-#ifndef SKCS_OVERWRITE_STATUS	/* User overwrite? */
-#define SKCS_STATUS	int	/* Define status type. */
-
-#define SKCS_STATUS_UNKNOWN_IP_VERSION	1
-#define SKCS_STATUS_IP_CSUM_ERROR		2
-#define SKCS_STATUS_IP_FRAGMENT			3
-#define SKCS_STATUS_IP_CSUM_OK			4
-#define SKCS_STATUS_TCP_CSUM_ERROR		5
-#define SKCS_STATUS_UDP_CSUM_ERROR		6
-#define SKCS_STATUS_TCP_CSUM_OK			7
-#define SKCS_STATUS_UDP_CSUM_OK			8
-/* needed for Microsoft */
-#define SKCS_STATUS_IP_CSUM_ERROR_UDP	9
-#define SKCS_STATUS_IP_CSUM_ERROR_TCP	10
-/* UDP checksum may be omitted */
-#define SKCS_STATUS_IP_CSUM_OK_NO_UDP	11
-#endif	/* !SKCS_OVERWRITE_STATUS */
-
-/* Clear protocol statistics event. */
-#define SK_CSUM_EVENT_CLEAR_PROTO_STATS	1
-
-/*
- * Add two values in one's complement.
- *
- * Note: One of the two input values may be "longer" than 16-bit, but then the
- * resulting sum may be 17 bits long. In this case, add zero to the result using
- * SKCS_OC_ADD() again.
- *
- *	Result = Value1 + Value2
- */
-#define SKCS_OC_ADD(Result, Value1, Value2) {				\
-	unsigned long Sum;						\
-									\
-	Sum = (unsigned long) (Value1) + (unsigned long) (Value2);	\
-	/* Add-in any carry. */						\
-	(Result) = (Sum & 0xffff) + (Sum >> 16);			\
-}
-
-/*
- * Subtract two values in one's complement.
- *
- *	Result = Value1 - Value2
- */
-#define SKCS_OC_SUB(Result, Value1, Value2)	\
-	SKCS_OC_ADD((Result), (Value1), ~(Value2) & 0xffff)
-
-/* typedefs *******************************************************************/
-
-/*
- * SKCS_PROTO_STATS - The CSUM protocol statistics structure.
- *
- * There is one instance of this structure for each protocol supported.
- */
-typedef struct s_CsProtocolStatistics {
-	SK_U64 RxOkCts;		/* Receive checksum ok. */
-	SK_U64 RxUnableCts;	/* Unable to verify receive checksum. */
-	SK_U64 RxErrCts;	/* Receive checksum error. */
-	SK_U64 TxOkCts;		/* Transmit checksum ok. */
-	SK_U64 TxUnableCts;	/* Unable to calculate checksum in hw. */
-} SKCS_PROTO_STATS;
-
-/*
- * s_Csum - The CSUM module context structure.
- */
-typedef struct s_Csum {
-	/* Enabled receive SK_PROTO_XXX bit flags. */
-	unsigned ReceiveFlags[SK_MAX_NETS];
-#ifdef TX_CSUM
-	unsigned TransmitFlags[SK_MAX_NETS];
-#endif /* TX_CSUM */
-
-	/* The protocol statistics structure; one per supported protocol. */
-	SKCS_PROTO_STATS ProtoStats[SK_MAX_NETS][SKCS_NUM_PROTOCOLS];
-} SK_CSUM;
-
-/*
- * SKCS_PACKET_INFO - The packet information structure.
- */
-typedef struct s_CsPacketInfo {
-	/* Bit field specifiying the desired/found protocols. */
-	unsigned ProtocolFlags;
-
-	/* Length of complete IP header, including any option fields. */
-	unsigned IpHeaderLength;
-
-	/* IP header checksum. */
-	unsigned IpHeaderChecksum;
-
-	/* TCP/UDP pseudo header checksum. */
-	unsigned PseudoHeaderChecksum;
-} SKCS_PACKET_INFO;
-
-/* function prototypes ********************************************************/
-
-#ifndef SK_CS_CALCULATE_CHECKSUM
-extern unsigned SkCsCalculateChecksum(
-	void		*pData,
-	unsigned	Length);
-#endif /* SK_CS_CALCULATE_CHECKSUM */
-
-extern int SkCsEvent(
-	SK_AC		*pAc,
-	SK_IOC		Ioc,
-	SK_U32		Event,
-	SK_EVPARA	Param);
-
-extern SKCS_STATUS SkCsGetReceiveInfo(
-	SK_AC		*pAc,
-	void		*pIpHeader,
-	unsigned	Checksum1,
-	unsigned	Checksum2,
-	int			NetNumber);
-
-extern void SkCsSetReceiveFlags(
-	SK_AC		*pAc,
-	unsigned	ReceiveFlags,
-	unsigned	*pChecksum1Offset,
-	unsigned	*pChecksum2Offset,
-	int			NetNumber);
-
-#endif	/* __INC_SKCSUM_H */

drivers/net/sk98lin/h/skdebug.h

-/******************************************************************************
- *
- * Name:	skdebug.h
- * Project:	Gigabit Ethernet Adapters, Common Modules
- * Version:	$Revision: 1.14 $
- * Date:	$Date: 2003/05/13 17:26:00 $
- * Purpose:	SK specific DEBUG support
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-#ifndef __INC_SKDEBUG_H
-#define __INC_SKDEBUG_H
-
-#ifdef	DEBUG
-#ifndef SK_DBG_MSG
-#define SK_DBG_MSG(pAC,comp,cat,arg) \
-		if ( ((comp) & SK_DBG_CHKMOD(pAC)) && 	\
-		      ((cat) & SK_DBG_CHKCAT(pAC)) ) { 	\
-			SK_DBG_PRINTF arg ;		\
-		}
-#endif
-#else
-#define SK_DBG_MSG(pAC,comp,lev,arg)
-#endif
-
-/* PLS NOTE:
- * =========
- * Due to any restrictions of kernel printf routines do not use other
- * format identifiers as: %x %d %c %s .
- * Never use any combined format identifiers such as: %lx %ld in your
- * printf - argument (arg) because some OS specific kernel printfs may
- * only support some basic identifiers.
- */
-
-/* Debug modules */
-
-#define SK_DBGMOD_MERR	0x00000001L	/* general module error indication */
-#define SK_DBGMOD_HWM	0x00000002L	/* Hardware init module */
-#define SK_DBGMOD_RLMT	0x00000004L	/* RLMT module */
-#define SK_DBGMOD_VPD	0x00000008L	/* VPD module */
-#define SK_DBGMOD_I2C	0x00000010L	/* I2C module */
-#define SK_DBGMOD_PNMI	0x00000020L	/* PNMI module */
-#define SK_DBGMOD_CSUM	0x00000040L	/* CSUM module */
-#define SK_DBGMOD_ADDR	0x00000080L	/* ADDR module */
-#define SK_DBGMOD_PECP	0x00000100L	/* PECP module */
-#define SK_DBGMOD_POWM	0x00000200L	/* Power Management module */
-
-/* Debug events */
-
-#define SK_DBGCAT_INIT	0x00000001L	/* module/driver initialization */
-#define SK_DBGCAT_CTRL	0x00000002L	/* controlling devices */
-#define SK_DBGCAT_ERR	0x00000004L	/* error handling paths */
-#define SK_DBGCAT_TX	0x00000008L	/* transmit path */
-#define SK_DBGCAT_RX	0x00000010L	/* receive path */
-#define SK_DBGCAT_IRQ	0x00000020L	/* general IRQ handling */
-#define SK_DBGCAT_QUEUE	0x00000040L	/* any queue management */
-#define SK_DBGCAT_DUMP	0x00000080L	/* large data output e.g. hex dump */
-#define SK_DBGCAT_FATAL	0x00000100L	/* fatal error */
-
-#endif	/* __INC_SKDEBUG_H */

drivers/net/sk98lin/h/skdrv1st.h

-/******************************************************************************
- *
- * Name:	skdrv1st.h
- * Project:	GEnesis, PCI Gigabit Ethernet Adapter
- * Version:	$Revision: 1.4 $
- * Date:	$Date: 2003/11/12 14:28:14 $
- * Purpose:	First header file for driver and all other modules
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect GmbH.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- * Description:
- *
- * This is the first include file of the driver, which includes all
- * neccessary system header files and some of the GEnesis header files.
- * It also defines some basic items.
- *
- * Include File Hierarchy:
- *
- *	see skge.c
- *
- ******************************************************************************/
-
-#ifndef __INC_SKDRV1ST_H
-#define __INC_SKDRV1ST_H
-
-typedef struct s_AC	SK_AC;
-
-/* Set card versions */
-#define SK_FAR
-
-/* override some default functions with optimized linux functions */
-
-#define SK_PNMI_STORE_U16(p,v)		memcpy((char*)(p),(char*)&(v),2)
-#define SK_PNMI_STORE_U32(p,v)		memcpy((char*)(p),(char*)&(v),4)
-#define SK_PNMI_STORE_U64(p,v)		memcpy((char*)(p),(char*)&(v),8)
-#define SK_PNMI_READ_U16(p,v)		memcpy((char*)&(v),(char*)(p),2)
-#define SK_PNMI_READ_U32(p,v)		memcpy((char*)&(v),(char*)(p),4)
-#define SK_PNMI_READ_U64(p,v)		memcpy((char*)&(v),(char*)(p),8)
-
-#define SK_ADDR_EQUAL(a1,a2)		(!memcmp(a1,a2,6))
-
-#include <linux/types.h>
-#include <linux/kernel.h>
-#include <linux/string.h>
-#include <linux/errno.h>
-#include <linux/ioport.h>
-#include <linux/slab.h>
-#include <linux/interrupt.h>
-#include <linux/pci.h>
-#include <linux/bitops.h>
-#include <asm/byteorder.h>
-#include <asm/io.h>
-#include <asm/irq.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/skbuff.h>
-
-#include <linux/init.h>
-#include <asm/uaccess.h>
-#include <net/checksum.h>
-
-#define SK_CS_CALCULATE_CHECKSUM
-#ifndef CONFIG_X86_64
-#define SkCsCalculateChecksum(p,l)	((~ip_compute_csum(p, l)) & 0xffff)
-#else
-#define SkCsCalculateChecksum(p,l)	((~ip_fast_csum(p, l)) & 0xffff)
-#endif
-
-#include	"h/sktypes.h"
-#include	"h/skerror.h"
-#include	"h/skdebug.h"
-#include	"h/lm80.h"
-#include	"h/xmac_ii.h"
-
-#ifdef __LITTLE_ENDIAN
-#define SK_LITTLE_ENDIAN
-#else
-#define SK_BIG_ENDIAN
-#endif
-
-#define SK_NET_DEVICE	net_device
-
-
-/* we use gethrtime(), return unit: nanoseconds */
-#define SK_TICKS_PER_SEC	100
-
-#define	SK_MEM_MAPPED_IO
-
-// #define SK_RLMT_SLOW_LOOKAHEAD
-
-#define SK_MAX_MACS		2
-#define SK_MAX_NETS		2
-
-#define SK_IOC			char __iomem *
-
-typedef struct s_DrvRlmtMbuf SK_MBUF;
-
-#define	SK_CONST64	INT64_C
-#define	SK_CONSTU64	UINT64_C
-
-#define SK_MEMCPY(dest,src,size)	memcpy(dest,src,size)
-#define SK_MEMCMP(s1,s2,size)		memcmp(s1,s2,size)
-#define SK_MEMSET(dest,val,size)	memset(dest,val,size)
-#define SK_STRLEN(pStr)			strlen((char*)(pStr))
-#define SK_STRNCPY(pDest,pSrc,size)	strncpy((char*)(pDest),(char*)(pSrc),size)
-#define SK_STRCMP(pStr1,pStr2)		strcmp((char*)(pStr1),(char*)(pStr2))
-
-/* macros to access the adapter */
-#define SK_OUT8(b,a,v)		writeb((v), ((b)+(a)))	
-#define SK_OUT16(b,a,v)		writew((v), ((b)+(a)))	
-#define SK_OUT32(b,a,v)		writel((v), ((b)+(a)))	
-#define SK_IN8(b,a,pv)		(*(pv) = readb((b)+(a)))
-#define SK_IN16(b,a,pv)		(*(pv) = readw((b)+(a)))
-#define SK_IN32(b,a,pv)		(*(pv) = readl((b)+(a)))
-
-#define int8_t		char
-#define int16_t		short
-#define int32_t		long
-#define int64_t		long long
-#define uint8_t		u_char
-#define uint16_t	u_short
-#define uint32_t	u_long
-#define uint64_t	unsigned long long
-#define t_scalar_t	int
-#define t_uscalar_t	unsigned int
-#define uintptr_t	unsigned long
-
-#define __CONCAT__(A,B) A##B
-
-#define INT32_C(a)		__CONCAT__(a,L)
-#define INT64_C(a)		__CONCAT__(a,LL)
-#define UINT32_C(a)		__CONCAT__(a,UL)
-#define UINT64_C(a)		__CONCAT__(a,ULL)
-
-#ifdef DEBUG
-#define SK_DBG_PRINTF		printk
-#ifndef SK_DEBUG_CHKMOD
-#define SK_DEBUG_CHKMOD		0
-#endif
-#ifndef SK_DEBUG_CHKCAT
-#define SK_DEBUG_CHKCAT		0
-#endif
-/* those come from the makefile */
-#define SK_DBG_CHKMOD(pAC)	(SK_DEBUG_CHKMOD)
-#define SK_DBG_CHKCAT(pAC)	(SK_DEBUG_CHKCAT)
-
-extern void SkDbgPrintf(const char *format,...);
-
-#define SK_DBGMOD_DRV			0x00010000
-
-/**** possible driver debug categories ********************************/
-#define SK_DBGCAT_DRV_ENTRY		0x00010000
-#define SK_DBGCAT_DRV_SAP		0x00020000
-#define SK_DBGCAT_DRV_MCA		0x00040000
-#define SK_DBGCAT_DRV_TX_PROGRESS	0x00080000
-#define SK_DBGCAT_DRV_RX_PROGRESS	0x00100000
-#define SK_DBGCAT_DRV_PROGRESS		0x00200000
-#define SK_DBGCAT_DRV_MSG		0x00400000
-#define SK_DBGCAT_DRV_PROM		0x00800000
-#define SK_DBGCAT_DRV_TX_FRAME		0x01000000
-#define SK_DBGCAT_DRV_ERROR		0x02000000
-#define SK_DBGCAT_DRV_INT_SRC		0x04000000
-#define SK_DBGCAT_DRV_EVENT		0x08000000
-
-#endif
-
-#define SK_ERR_LOG		SkErrorLog
-
-extern void SkErrorLog(SK_AC*, int, int, char*);
-
-#endif
-

drivers/net/sk98lin/h/skerror.h

-/******************************************************************************
- *
- * Name:	skerror.h
- * Project:	Gigabit Ethernet Adapters, Common Modules
- * Version:	$Revision: 1.7 $
- * Date:	$Date: 2003/05/13 17:25:13 $
- * Purpose:	SK specific Error log support
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-#ifndef _INC_SKERROR_H_
-#define _INC_SKERROR_H_
-
-/*
- * Define Error Classes
- */
-#define	SK_ERRCL_OTHER		(0)		/* Other error */
-#define	SK_ERRCL_CONFIG		(1L<<0)	/* Configuration error */
-#define	SK_ERRCL_INIT		(1L<<1)	/* Initialization error */
-#define	SK_ERRCL_NORES		(1L<<2)	/* Out of Resources error */
-#define	SK_ERRCL_SW			(1L<<3)	/* Internal Software error */
-#define	SK_ERRCL_HW			(1L<<4)	/* Hardware Failure */
-#define	SK_ERRCL_COMM		(1L<<5)	/* Communication error */
-
-
-/*
- * Define Error Code Bases
- */
-#define	SK_ERRBASE_RLMT		 100	/* Base Error number for RLMT */
-#define	SK_ERRBASE_HWINIT	 200	/* Base Error number for HWInit */
-#define	SK_ERRBASE_VPD		 300	/* Base Error number for VPD */
-#define	SK_ERRBASE_PNMI		 400	/* Base Error number for PNMI */
-#define	SK_ERRBASE_CSUM		 500	/* Base Error number for Checksum */
-#define	SK_ERRBASE_SIRQ		 600	/* Base Error number for Special IRQ */
-#define	SK_ERRBASE_I2C		 700	/* Base Error number for I2C module */
-#define	SK_ERRBASE_QUEUE	 800	/* Base Error number for Scheduler */
-#define	SK_ERRBASE_ADDR		 900	/* Base Error number for Address module */
-#define SK_ERRBASE_PECP		1000    /* Base Error number for PECP */
-#define	SK_ERRBASE_DRV		1100	/* Base Error number for Driver */
-
-#endif	/* _INC_SKERROR_H_ */

drivers/net/sk98lin/h/skgedrv.h

-/******************************************************************************
- *
- * Name:	skgedrv.h
- * Project:	Gigabit Ethernet Adapters, Common Modules
- * Version:	$Revision: 1.10 $
- * Date:	$Date: 2003/07/04 12:25:01 $
- * Purpose:	Interface with the driver
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-#ifndef __INC_SKGEDRV_H_
-#define __INC_SKGEDRV_H_
-
-/* defines ********************************************************************/
-
-/*
- * Define the driver events.
- * Usually the events are defined by the destination module.
- * In case of the driver we put the definition of the events here.
- */
-#define SK_DRV_PORT_RESET		 1	/* The port needs to be reset */
-#define SK_DRV_NET_UP   		 2	/* The net is operational */
-#define SK_DRV_NET_DOWN			 3	/* The net is down */
-#define SK_DRV_SWITCH_SOFT		 4	/* Ports switch with both links connected */
-#define SK_DRV_SWITCH_HARD		 5	/* Port switch due to link failure */
-#define SK_DRV_RLMT_SEND		 6	/* Send a RLMT packet */
-#define SK_DRV_ADAP_FAIL		 7	/* The whole adapter fails */
-#define SK_DRV_PORT_FAIL		 8	/* One port fails */
-#define SK_DRV_SWITCH_INTERN	 9	/* Port switch by the driver itself */
-#define SK_DRV_POWER_DOWN		10	/* Power down mode */
-#define SK_DRV_TIMER			11	/* Timer for free use */
-#ifdef SK_NO_RLMT
-#define SK_DRV_LINK_UP  		12	/* Link Up event for driver */
-#define SK_DRV_LINK_DOWN		13	/* Link Down event for driver */
-#endif
-#define SK_DRV_DOWNSHIFT_DET	14	/* Downshift 4-Pair / 2-Pair (YUKON only) */
-#endif /* __INC_SKGEDRV_H_ */

drivers/net/sk98lin/h/skgehwt.h

-/******************************************************************************
- *
- * Name:	skhwt.h
- * Project:	Gigabit Ethernet Adapters, Event Scheduler Module
- * Version:	$Revision: 1.7 $
- * Date:	$Date: 2003/09/16 12:55:08 $
- * Purpose:	Defines for the hardware timer functions
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect GmbH.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-/*
- * SKGEHWT.H	contains all defines and types for the timer functions
- */
-
-#ifndef	_SKGEHWT_H_
-#define _SKGEHWT_H_
-
-/*
- * SK Hardware Timer
- * - needed wherever the HWT module is used
- * - use in Adapters context name pAC->Hwt
- */
-typedef	struct s_Hwt {
-	SK_U32		TStart;	/* HWT start */
-	SK_U32		TStop;	/* HWT stop */
-	int		TActive;	/* HWT: flag : active/inactive */
-} SK_HWT;
-
-extern void SkHwtInit(SK_AC *pAC, SK_IOC Ioc);
-extern void SkHwtStart(SK_AC *pAC, SK_IOC Ioc, SK_U32 Time);
-extern void SkHwtStop(SK_AC *pAC, SK_IOC Ioc);
-extern SK_U32 SkHwtRead(SK_AC *pAC, SK_IOC Ioc);
-extern void SkHwtIsr(SK_AC *pAC, SK_IOC Ioc);
-#endif	/* _SKGEHWT_H_ */

drivers/net/sk98lin/h/skgei2c.h

-/******************************************************************************
- *
- * Name:	skgei2c.h
- * Project:	Gigabit Ethernet Adapters, TWSI-Module
- * Version:	$Revision: 1.25 $
- * Date:	$Date: 2003/10/20 09:06:05 $
- * Purpose:	Special defines for TWSI
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-/*
- * SKGEI2C.H	contains all SK-98xx specific defines for the TWSI handling
- */
-
-#ifndef _INC_SKGEI2C_H_
-#define _INC_SKGEI2C_H_
-
-/*
- * Macros to access the B2_I2C_CTRL
- */
-#define SK_I2C_CTL(IoC, flag, dev, dev_size, reg, burst) \
-	SK_OUT32(IoC, B2_I2C_CTRL,\
-		(flag ? 0x80000000UL : 0x0L) | \
-		(((SK_U32)reg << 16) & I2C_ADDR) | \
-		(((SK_U32)dev << 9) & I2C_DEV_SEL) | \
-		(dev_size & I2C_DEV_SIZE) | \
-		((burst << 4) & I2C_BURST_LEN))
-
-#define SK_I2C_STOP(IoC) {				\
-	SK_U32	I2cCtrl;				\
-	SK_IN32(IoC, B2_I2C_CTRL, &I2cCtrl);		\
-	SK_OUT32(IoC, B2_I2C_CTRL, I2cCtrl | I2C_STOP);	\
-}
-
-#define SK_I2C_GET_CTL(IoC, pI2cCtrl)	SK_IN32(IoC, B2_I2C_CTRL, pI2cCtrl)
-
-/*
- * Macros to access the TWSI SW Registers
- */
-#define SK_I2C_SET_BIT(IoC, SetBits) {			\
-	SK_U8	OrgBits;				\
-	SK_IN8(IoC, B2_I2C_SW, &OrgBits);		\
-	SK_OUT8(IoC, B2_I2C_SW, OrgBits | (SK_U8)(SetBits));	\
-}
-
-#define SK_I2C_CLR_BIT(IoC, ClrBits) {			\
-	SK_U8	OrgBits;				\
-	SK_IN8(IoC, B2_I2C_SW, &OrgBits);		\
-	SK_OUT8(IoC, B2_I2C_SW, OrgBits & ~((SK_U8)(ClrBits)));	\
-}
-
-#define SK_I2C_GET_SW(IoC, pI2cSw)	SK_IN8(IoC, B2_I2C_SW, pI2cSw)
-
-/*
- * define the possible sensor states
- */
-#define	SK_SEN_IDLE		0	/* Idle: sensor not read */
-#define	SK_SEN_VALUE	1	/* Value Read cycle */
-#define	SK_SEN_VALEXT	2	/* Extended Value Read cycle */
-
-/*
- * Conversion factor to convert read Voltage sensor to milli Volt
- * Conversion factor to convert read Temperature sensor to 10th degree Celsius
- */
-#define	SK_LM80_VT_LSB		22	/* 22mV LSB resolution */
-#define	SK_LM80_TEMP_LSB	10	/* 1 degree LSB resolution */
-#define	SK_LM80_TEMPEXT_LSB	 5	/* 0.5 degree LSB resolution for ext. val. */
-
-/*
- * formula: counter = (22500*60)/(rpm * divisor * pulses/2)
- * assuming: 6500rpm, 4 pulses, divisor 1
- */
-#define SK_LM80_FAN_FAKTOR	((22500L*60)/(1*2))
-
-/*
- * Define sensor management data
- * Maximum is reached on Genesis copper dual port and Yukon-64
- * Board specific maximum is in pAC->I2c.MaxSens
- */
-#define	SK_MAX_SENSORS	8	/* maximal no. of installed sensors */
-#define	SK_MIN_SENSORS	5	/* minimal no. of installed sensors */
-
-/*
- * To watch the state machine (SM) use the timer in two ways
- * instead of one as hitherto
- */
-#define	SK_TIMER_WATCH_SM		0	/* Watch the SM to finish in a spec. time */
-#define	SK_TIMER_NEW_GAUGING	1	/* Start a new gauging when timer expires */
-
-/*
- * Defines for the individual thresholds
- */
-
-/* Temperature sensor */
-#define	SK_SEN_TEMP_HIGH_ERR	800	/* Temperature High Err  Threshold */
-#define	SK_SEN_TEMP_HIGH_WARN	700	/* Temperature High Warn Threshold */
-#define	SK_SEN_TEMP_LOW_WARN	100	/* Temperature Low  Warn Threshold */
-#define	SK_SEN_TEMP_LOW_ERR		  0	/* Temperature Low  Err  Threshold */
-
-/* VCC which should be 5 V */
-#define	SK_SEN_PCI_5V_HIGH_ERR		5588	/* Voltage PCI High Err  Threshold */
-#define	SK_SEN_PCI_5V_HIGH_WARN		5346	/* Voltage PCI High Warn Threshold */
-#define	SK_SEN_PCI_5V_LOW_WARN		4664	/* Voltage PCI Low  Warn Threshold */
-#define	SK_SEN_PCI_5V_LOW_ERR		4422	/* Voltage PCI Low  Err  Threshold */
-
-/*
- * VIO may be 5 V or 3.3 V. Initialization takes two parts:
- * 1. Initialize lowest lower limit and highest higher limit.
- * 2. After the first value is read correct the upper or the lower limit to
- *    the appropriate C constant.
- *
- * Warning limits are +-5% of the exepected voltage.
- * Error limits are +-10% of the expected voltage.
- */
-
-/* Bug fix AF: 16.Aug.2001: Correct the init base of LM80 sensor */
-
-#define	SK_SEN_PCI_IO_5V_HIGH_ERR	5566	/* + 10% V PCI-IO High Err Threshold */
-#define	SK_SEN_PCI_IO_5V_HIGH_WARN	5324	/* +  5% V PCI-IO High Warn Threshold */
-					/*		5000	mVolt */
-#define	SK_SEN_PCI_IO_5V_LOW_WARN	4686	/* -  5% V PCI-IO Low Warn Threshold */
-#define	SK_SEN_PCI_IO_5V_LOW_ERR	4444	/* - 10% V PCI-IO Low Err Threshold */
-
-#define	SK_SEN_PCI_IO_RANGE_LIMITER	4000	/* 4000 mV range delimiter */
-
-/* correction values for the second pass */
-#define	SK_SEN_PCI_IO_3V3_HIGH_ERR	3850	/* + 15% V PCI-IO High Err Threshold */
-#define	SK_SEN_PCI_IO_3V3_HIGH_WARN	3674	/* + 10% V PCI-IO High Warn Threshold */
-					/*		3300	mVolt */
-#define	SK_SEN_PCI_IO_3V3_LOW_WARN	2926	/* - 10% V PCI-IO Low Warn Threshold */
-#define	SK_SEN_PCI_IO_3V3_LOW_ERR	2772	/* - 15% V PCI-IO Low Err  Threshold */
-
-/*
- * VDD voltage
- */
-#define	SK_SEN_VDD_HIGH_ERR		3630	/* Voltage ASIC High Err  Threshold */
-#define	SK_SEN_VDD_HIGH_WARN	3476	/* Voltage ASIC High Warn Threshold */
-#define	SK_SEN_VDD_LOW_WARN		3146	/* Voltage ASIC Low  Warn Threshold */
-#define	SK_SEN_VDD_LOW_ERR		2970	/* Voltage ASIC Low  Err  Threshold */
-
-/*
- * PHY PLL 3V3 voltage
- */
-#define	SK_SEN_PLL_3V3_HIGH_ERR		3630	/* Voltage PMA High Err  Threshold */
-#define	SK_SEN_PLL_3V3_HIGH_WARN	3476	/* Voltage PMA High Warn Threshold */
-#define	SK_SEN_PLL_3V3_LOW_WARN		3146	/* Voltage PMA Low  Warn Threshold */
-#define	SK_SEN_PLL_3V3_LOW_ERR		2970	/* Voltage PMA Low  Err  Threshold */
-
-/*
- * VAUX (YUKON only)
- */
-#define	SK_SEN_VAUX_3V3_HIGH_ERR	3630	/* Voltage VAUX High Err Threshold */
-#define	SK_SEN_VAUX_3V3_HIGH_WARN	3476	/* Voltage VAUX High Warn Threshold */
-#define	SK_SEN_VAUX_3V3_LOW_WARN	3146	/* Voltage VAUX Low Warn Threshold */
-#define	SK_SEN_VAUX_3V3_LOW_ERR		2970	/* Voltage VAUX Low Err Threshold */
-#define	SK_SEN_VAUX_0V_WARN_ERR		   0	/* if VAUX not present */
-#define	SK_SEN_VAUX_RANGE_LIMITER	1000	/* 1000 mV range delimiter */
-
-/*
- * PHY 2V5 voltage
- */
-#define	SK_SEN_PHY_2V5_HIGH_ERR		2750	/* Voltage PHY High Err Threshold */
-#define	SK_SEN_PHY_2V5_HIGH_WARN	2640	/* Voltage PHY High Warn Threshold */
-#define	SK_SEN_PHY_2V5_LOW_WARN		2376	/* Voltage PHY Low Warn Threshold */
-#define	SK_SEN_PHY_2V5_LOW_ERR		2222	/* Voltage PHY Low Err Threshold */
-
-/*
- * ASIC Core 1V5 voltage (YUKON only)
- */
-#define	SK_SEN_CORE_1V5_HIGH_ERR	1650	/* Voltage ASIC Core High Err Threshold */
-#define	SK_SEN_CORE_1V5_HIGH_WARN	1575	/* Voltage ASIC Core High Warn Threshold */
-#define	SK_SEN_CORE_1V5_LOW_WARN	1425	/* Voltage ASIC Core Low Warn Threshold */
-#define	SK_SEN_CORE_1V5_LOW_ERR 	1350	/* Voltage ASIC Core Low Err Threshold */
-
-/*
- * FAN 1 speed
- */
-/* assuming: 6500rpm +-15%, 4 pulses,
- * warning at:	80 %
- * error at:	70 %
- * no upper limit
- */
-#define	SK_SEN_FAN_HIGH_ERR		20000	/* FAN Speed High Err Threshold */
-#define	SK_SEN_FAN_HIGH_WARN	20000	/* FAN Speed High Warn Threshold */
-#define	SK_SEN_FAN_LOW_WARN		 5200	/* FAN Speed Low Warn Threshold */
-#define	SK_SEN_FAN_LOW_ERR		 4550	/* FAN Speed Low Err Threshold */
-
-/*
- * Some Voltages need dynamic thresholds
- */
-#define	SK_SEN_DYN_INIT_NONE		 0  /* No dynamic init of thresholds */
-#define	SK_SEN_DYN_INIT_PCI_IO		10  /* Init PCI-IO with new thresholds */
-#define	SK_SEN_DYN_INIT_VAUX		11  /* Init VAUX with new thresholds */
-
-extern	int SkLm80ReadSensor(SK_AC *pAC, SK_IOC IoC, SK_SENSOR *pSen);
-#endif	/* n_INC_SKGEI2C_H */

drivers/net/sk98lin/h/skgesirq.h

-/******************************************************************************
- *
- * Name:	skgesirq.h
- * Project:	Gigabit Ethernet Adapters, Common Modules
- * Version:	$Revision: 1.30 $
- * Date:	$Date: 2003/07/04 12:34:13 $
- * Purpose:	SK specific Gigabit Ethernet special IRQ functions
- *
- ******************************************************************************/
-
-/******************************************************************************
- *
- *	(C)Copyright 1998-2002 SysKonnect.
- *	(C)Copyright 2002-2003 Marvell.
- *
- *	This program is free software; you can redistribute it and/or modify
- *	it under the terms of the GNU General Public License as published by
- *	the Free Software Foundation; either version 2 of the License, or
- *	(at your option) any later version.
- *
- *	The information in this file is provided "AS IS" without warranty.
- *
- ******************************************************************************/
-
-#ifndef _INC_SKGESIRQ_H_
-#define _INC_SKGESIRQ_H_
-
-/* Define return codes of SkGePortCheckUp and CheckShort */
-#define	SK_HW_PS_NONE		0	/* No action needed */
-#define	SK_HW_PS_RESTART	1	/* Restart needed */
-#define	SK_HW_PS_LINK		2	/* Link Up actions needed */
-
-/*
- * Define the Event the special IRQ/INI module can handle
- */
-#define SK_HWEV_WATIM			1	/* Timeout for WA Errata #2 XMAC */
-#define SK_HWEV_PORT_START		2	/* Port Start Event by RLMT */
-#define SK_HWEV_PORT_STOP		3	/* Port Stop Event by RLMT */
-#define SK_HWEV_CLEAR_STAT		4	/* Clear Statistics by PNMI */
-#define SK_HWEV_UPDATE_STAT		5	/* Update Statistics by PNMI */
-#define SK_HWEV_SET_LMODE		6	/* Set Link Mode by PNMI */
-#define SK_HWEV_SET_FLOWMODE	7	/* Set Flow Control Mode by PNMI */
-#define SK_HWEV_SET_ROLE		8	/* Set Master/Slave (Role) by PNMI */
-#define SK_HWEV_SET_SPEED		9	/* Set Link Speed by PNMI */
-#define SK_HWEV_HALFDUP_CHK		10	/* Half Duplex Hangup Workaround */
-
-#define SK_WA_ACT_TIME		(5000000UL)	/* 5 sec */
-#define SK_WA_INA_TIME		(100000UL)	/* 100 msec */
-
-#define SK_HALFDUP_CHK_TIME	(10000UL)	/* 10 msec */
-
-/*
- * Define the error numbers and messages
- */
-#define SKERR_SIRQ_E001		(SK_ERRBASE_SIRQ+0)
-#define SKERR_SIRQ_E001MSG	"Unknown event"
-#define SKERR_SIRQ_E002		(SKERR_SIRQ_E001+1)
-#define SKERR_SIRQ_E002MSG	"Packet timeout RX1"
-#define SKERR_SIRQ_E003		(SKERR_SIRQ_E002+1)
-#define SKERR_SIRQ_E003MSG	"Packet timeout RX2"
-#define SKERR_SIRQ_E004		(SKERR_SIRQ_E003+1)
-#define SKERR_SIRQ_E004MSG	"MAC 1 not correctly initialized"
-#define SKERR_SIRQ_E005		(SKERR_SIRQ_E004+1)
-#define SKERR_SIRQ_E005MSG	"MAC 2 not correctly initialized"
-#define SKERR_SIRQ_E006		(SKERR_SIRQ_E005+1)
-#define SKERR_SIRQ_E006MSG	"CHECK failure R1"
-#define SKERR_SIRQ_E007		(SKERR_SIRQ_E006+1)
-#define SKERR_SIRQ_E007MSG	"CHECK failure R2"
-#define SKERR_SIRQ_E008		(SKERR_SIRQ_E007+1)
-#define SKERR_SIRQ_E008MSG	"CHECK failure XS1"
-#define SKERR_SIRQ_E009		(SKERR_SIRQ_E008+1)
-#define SKERR_SIRQ_E009MSG	"CHECK failure XA1"
-#define SKERR_SIRQ_E010		(SKERR_SIRQ_E009+1)
-#define SKERR_SIRQ_E010MSG	"CHECK failure XS2"
-#define SKERR_SIRQ_E011		(SKERR_SIRQ_E010+1)
-#define SKERR_SIRQ_E011MSG	"CHECK failure XA2"
-#define SKERR_SIRQ_E012		(SKERR_SIRQ_E011+1)
-#define SKERR_SIRQ_E012MSG	"unexpected IRQ Master error"
-#define SKERR_SIRQ_E013		(SKERR_SIRQ_E012+1)
-#define SKERR_SIRQ_E013MSG	"unexpected IRQ Status error"
-#define SKERR_SIRQ_E014		(SKERR_SIRQ_E013+1)
-#define SKERR_SIRQ_E014MSG	"Parity error on RAM (read)"
-#define SKERR_SIRQ_E015		(SKERR_SIRQ_E014+1)
-#define SKERR_SIRQ_E015MSG	"Parity error on RAM (write)"
-#define SKERR_SIRQ_E016		(SKERR_SIRQ_E015+1)
-#define SKERR_SIRQ_E016MSG	"Parity error MAC 1"
-#define SKERR_SIRQ_E017		(SKERR_SIRQ_E016+1)
-#define SKERR_SIRQ_E017MSG	"Parity error MAC 2"
-#define SKERR_SIRQ_E018		(SKERR_SIRQ_E017+1)
-#define SKERR_SIRQ_E018MSG	"Parity error RX 1"
-#define SKERR_SIRQ_E019		(SKERR_SIRQ_E018+1)
-#define SKERR_SIRQ_E019MSG	"Parity error RX 2"
-#define SKERR_SIRQ_E020		(SKERR_SIRQ_E019+1)
-#define SKERR_SIRQ_E020MSG	"MAC transmit FIFO underrun"
-#define SKERR_SIRQ_E021		(SKERR_SIRQ_E020+1)
-#define SKERR_SIRQ_E021MSG	"Spurious TWSI interrupt"
-#define SKERR_SIRQ_E022		(SKERR_SIRQ_E021+1)
-#define SKERR_SIRQ_E022MSG	"Cable pair swap error"
-#define SKERR_SIRQ_E023		(SKERR_SIRQ_E022+1)
-#define SKERR_SIRQ_E023MSG	"Auto-negotiation error"
-#define SKERR_SIRQ_E024		(SKERR_SIRQ_E023+1)
-#define SKERR_SIRQ_E024MSG	"FIFO overflow error"
-#define SKERR_SIRQ_E025		(SKERR_SIRQ_E024+1)
-#define SKERR_SIRQ_E025MSG	"2 Pair Downshift detected"
-
-extern void SkGeSirqIsr(SK_AC *pAC, SK_IOC IoC, SK_U32 Istatus);
-extern int  SkGeSirqEvent(SK_AC *pAC, SK_IOC IoC, SK_U32 Event, SK_EVPARA Para);
-extern void SkHWLinkDown(SK_AC *pAC, SK_IOC IoC, int Port);
-
-#endif	/* _INC_SKGESIRQ_H_ */