Merge tag 'qcom-drivers-for-4.10' of...

Merge tag 'qcom-drivers-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux into next/drivers

Qualcomm ARM Based Driver Updates for v4.10

* Fixup QCOM SCM to use devm_reset_controller_register
* Add QCOM pinctrl to Qualcomm MAINTAINERS entry
* Add PM8994 regulator definitions
* Add stub for WCNSS_CTRL API

* tag 'qcom-drivers-for-4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/agross/linux:
  firmware: qcom: scm: Use devm_reset_controller_register()
  MAINTAINERS: add drivers/pinctrl/qcom to ARM/QUALCOMM SUPPORT
  pinctrl: pm8994: add pad voltage regulator defines
  soc: qcom: wcnss_ctrl: Stub wcnss_ctrl API
Signed-off-by: Olof Johansson <olof@lixom.net>

MAINTAINERS

@@ -1600,6 +1600,7 @@ F:	arch/arm/mach-qcom/
 F:	arch/arm64/boot/dts/qcom/*
 F:	drivers/i2c/busses/i2c-qup.c
 F:	drivers/clk/qcom/
+F:	drivers/pinctrl/qcom/
 F:	drivers/soc/qcom/
 F:	drivers/spi/spi-qup.c
 F:	drivers/tty/serial/msm_serial.h

drivers/firmware/qcom_scm.c

@@ -356,7 +356,9 @@ static int qcom_scm_probe(struct platform_device *pdev)
 	scm->reset.ops = &qcom_scm_pas_reset_ops;
 	scm->reset.nr_resets = 1;
 	scm->reset.of_node = pdev->dev.of_node;
-	reset_controller_register(&scm->reset);
+	ret = devm_reset_controller_register(&pdev->dev, &scm->reset);
+	if (ret)
+		return ret;
 
 	/* vote for max clk rate for highest performance */
 	ret = clk_set_rate(scm->core_clk, INT_MAX);

include/dt-bindings/pinctrl/qcom,pmic-gpio.h

@@ -89,6 +89,10 @@
 #define PMA8084_GPIO_S4			2
 #define PMA8084_GPIO_L6			3
 
+#define PM8994_GPIO_VPH			0
+#define PM8994_GPIO_S4			2
+#define PM8994_GPIO_L12			3
+
 /* To be used with "function" */
 #define PMIC_GPIO_FUNC_NORMAL		"normal"
 #define PMIC_GPIO_FUNC_PAIRED		"paired"

include/dt-bindings/pinctrl/qcom,pmic-mpp.h

@@ -65,6 +65,12 @@
 #define PMA8084_MPP_S4			2
 #define PMA8084_MPP_L6			3
 
+#define PM8994_MPP_VPH			0
+/* Only supported for MPP_05-MPP_08 */
+#define PM8994_MPP_L19			1
+#define PM8994_MPP_S4			2
+#define PM8994_MPP_L12			3
+
 /*
  * Analog Input - Set the source for analog input.
  * To be used with "qcom,amux-route" property

include/linux/soc/qcom/wcnss_ctrl.h

@@ -3,6 +3,19 @@
 
 #include <linux/soc/qcom/smd.h>
 
+#if IS_ENABLED(CONFIG_QCOM_WCNSS_CTRL)
+
 struct qcom_smd_channel *qcom_wcnss_open_channel(void *wcnss, const char *name, qcom_smd_cb_t cb);
 
+#else
+
+static inline struct qcom_smd_channel*
+qcom_wcnss_open_channel(void *wcnss, const char *name, qcom_smd_cb_t cb)
+{
+	WARN_ON(1);
+	return ERR_PTR(-ENXIO);
+}
+
+#endif
+
 #endif