Commit 56c22854 authored by Linus Torvalds's avatar Linus Torvalds

Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc

Pull ARM SoC fixes from Kevin Hilman:
 "Another round of fixes from arm-soc land, which are mostly DT fixes
  for:

   - OMAP: handful of DT fixes devices on newly supported hardware
   - davinci: fix 2nd EDMA channel
   - ux500: extend previous pinctrl fix to another board
   - at91: clock registration fixes, compatibility string precision

  And one more fix for event cleanup in drivers/bus/arm-ccn"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  bus: arm-ccn: Move event cleanup routine
  ARM: at91/dt: rm9200: fix usb clock definition
  ARM: at91: rm9200: fix clock registration
  ARM: at91/dt: sam9g20: set at91sam9g20 pllb driver
  ARM: dts: dra7-evm: Add vtt regulator support
  ARM: dts: dra7-evm: Fix spi1 mux documentation
  ARM: dts: am43x-epos-evm: Disable QSPI to prevent conflict with GPMC-NAND
  ARM: OMAP2+: gpmc: Don't complain if wait pin is used without r/w monitoring
  ARM: dts: am43xx-epos-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Don't use read/write wait monitoring
  ARM: dts: am437x-gp-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am43x-epos-evm: Use BCH16 ECC scheme instead of BCH8
  ARM: dts: am4372: fix USB regs size
  ARM: dts: am437x-gp: switch i2c0 to 100KHz
  ARM: dts: dra7-evm: Fix 8th NAND partition's name
  ARM: dts: dra7-evm: Fix i2c3 pinmux and frequency
  ARM: ux500: disable msp2 node on Snowball
  ARM: edma: Fix configuration parsing for SoCs with multiple eDMA3 CC
  ARM: dts: set 'ti,set-rate-parent' for dpll4_m5x2 clock
parents 11e97398 38971083
......@@ -804,7 +804,7 @@ dwc3_1: omap_dwc3@48380000 {
usb1: usb@48390000 {
compatible = "synopsys,dwc3";
reg = <0x48390000 0x17000>;
reg = <0x48390000 0x10000>;
interrupts = <GIC_SPI 168 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb2_phy1>;
phy-names = "usb2-phy";
......@@ -826,7 +826,7 @@ dwc3_2: omap_dwc3@483c0000 {
usb2: usb@483d0000 {
compatible = "synopsys,dwc3";
reg = <0x483d0000 0x17000>;
reg = <0x483d0000 0x10000>;
interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
phys = <&usb2_phy2>;
phy-names = "usb2-phy";
......
......@@ -260,7 +260,7 @@ &i2c0 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c0_pins>;
clock-frequency = <400000>;
clock-frequency = <100000>;
tps65218: tps65218@24 {
reg = <0x24>;
......@@ -424,7 +424,7 @@ &gpmc {
ranges = <0 0 0 0x01000000>; /* minimum GPMC partition = 16MB */
nand@0,0 {
reg = <0 0 4>; /* device IO registers */
ti,nand-ecc-opt = "bch8";
ti,nand-ecc-opt = "bch16";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
gpmc,device-width = <1>;
......@@ -443,8 +443,6 @@ nand@0,0 {
gpmc,rd-cycle-ns = <40>;
gpmc,wr-cycle-ns = <40>;
gpmc,wait-pin = <0>;
gpmc,wait-on-read;
gpmc,wait-on-write;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,clk-activation-ns = <0>;
......
......@@ -435,13 +435,13 @@ &elm {
};
&gpmc {
status = "okay";
status = "okay"; /* Disable QSPI when enabling GPMC (NAND) */
pinctrl-names = "default";
pinctrl-0 = <&nand_flash_x8>;
ranges = <0 0 0x08000000 0x10000000>; /* CS0: NAND */
nand@0,0 {
reg = <0 0 0>; /* CS0, offset 0 */
ti,nand-ecc-opt = "bch8";
ti,nand-ecc-opt = "bch16";
ti,elm-id = <&elm>;
nand-bus-width = <8>;
gpmc,device-width = <1>;
......@@ -459,8 +459,7 @@ nand@0,0 {
gpmc,access-ns = <30>; /* tCEA + 4*/
gpmc,rd-cycle-ns = <40>;
gpmc,wr-cycle-ns = <40>;
gpmc,wait-on-read = "true";
gpmc,wait-on-write = "true";
gpmc,wait-pin = <0>;
gpmc,bus-turnaround-ns = <0>;
gpmc,cycle2cycle-delay-ns = <0>;
gpmc,clk-activation-ns = <0>;
......@@ -557,7 +556,7 @@ &usb2 {
};
&qspi {
status = "okay";
status = "disabled"; /* Disable GPMC (NAND) when enabling QSPI */
pinctrl-names = "default";
pinctrl-0 = <&qspi1_default>;
......
......@@ -149,7 +149,7 @@ mck: masterck {
usb: usbck {
compatible = "atmel,at91rm9200-clk-usb";
#clock-cells = <0>;
atmel,clk-divisors = <1 2>;
atmel,clk-divisors = <1 2 0 0>;
clocks = <&pllb>;
};
......
......@@ -40,6 +40,7 @@ plla: pllack {
};
pllb: pllbck {
compatible = "atmel,at91sam9g20-clk-pllb";
atmel,clk-input-range = <2000000 32000000>;
atmel,pll-clk-output-ranges = <30000000 100000000 0 0>;
};
......
......@@ -8,6 +8,7 @@
/dts-v1/;
#include "dra74x.dtsi"
#include <dt-bindings/gpio/gpio.h>
/ {
model = "TI DRA742";
......@@ -24,9 +25,29 @@ mmc2_3v3: fixedregulator-mmc2 {
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
};
vtt_fixed: fixedregulator-vtt {
compatible = "regulator-fixed";
regulator-name = "vtt_fixed";
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
regulator-boot-on;
enable-active-high;
gpio = <&gpio7 11 GPIO_ACTIVE_HIGH>;
};
};
&dra7_pmx_core {
pinctrl-names = "default";
pinctrl-0 = <&vtt_pin>;
vtt_pin: pinmux_vtt_pin {
pinctrl-single,pins = <
0x3b4 (PIN_OUTPUT | MUX_MODE14) /* spi1_cs1.gpio7_11 */
>;
};
i2c1_pins: pinmux_i2c1_pins {
pinctrl-single,pins = <
0x400 (PIN_INPUT | MUX_MODE0) /* i2c1_sda */
......@@ -43,20 +64,19 @@ i2c2_pins: pinmux_i2c2_pins {
i2c3_pins: pinmux_i2c3_pins {
pinctrl-single,pins = <
0x410 (PIN_INPUT | MUX_MODE0) /* i2c3_sda */
0x414 (PIN_INPUT | MUX_MODE0) /* i2c3_scl */
0x288 (PIN_INPUT | MUX_MODE9) /* gpio6_14.i2c3_sda */
0x28c (PIN_INPUT | MUX_MODE9) /* gpio6_15.i2c3_scl */
>;
};
mcspi1_pins: pinmux_mcspi1_pins {
pinctrl-single,pins = <
0x3a4 (PIN_INPUT | MUX_MODE0) /* spi2_clk */
0x3a8 (PIN_INPUT | MUX_MODE0) /* spi2_d1 */
0x3ac (PIN_INPUT | MUX_MODE0) /* spi2_d0 */
0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs0 */
0x3b4 (PIN_INPUT_SLEW | MUX_MODE0) /* spi2_cs1 */
0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs2 */
0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi2_cs3 */
0x3a4 (PIN_INPUT | MUX_MODE0) /* spi1_sclk */
0x3a8 (PIN_INPUT | MUX_MODE0) /* spi1_d1 */
0x3ac (PIN_INPUT | MUX_MODE0) /* spi1_d0 */
0x3b0 (PIN_INPUT_SLEW | MUX_MODE0) /* spi1_cs0 */
0x3b8 (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs2.hdmi1_hpd */
0x3bc (PIN_INPUT_SLEW | MUX_MODE6) /* spi1_cs3.hdmi1_cec */
>;
};
......@@ -284,7 +304,7 @@ &i2c3 {
status = "okay";
pinctrl-names = "default";
pinctrl-0 = <&i2c3_pins>;
clock-frequency = <3400000>;
clock-frequency = <400000>;
};
&mcspi1 {
......@@ -483,7 +503,7 @@ partition@6 {
reg = <0x001c0000 0x00020000>;
};
partition@7 {
label = "NAND.u-boot-env";
label = "NAND.u-boot-env.backup1";
reg = <0x001e0000 0x00020000>;
};
partition@8 {
......@@ -504,3 +524,8 @@ &usb2_phy1 {
&usb2_phy2 {
phy-supply = <&ldousb_reg>;
};
&gpio7 {
ti,no-reset-on-init;
ti,no-idle-on-init;
};
......@@ -467,6 +467,7 @@ dpll4_m5x2_ck: dpll4_m5x2_ck {
ti,bit-shift = <0x1e>;
reg = <0x0d00>;
ti,set-bit-to-disable;
ti,set-rate-parent;
};
dpll4_m6_ck: dpll4_m6_ck {
......
......@@ -116,7 +116,6 @@ msp1: msp@80124000 {
msp2: msp@80117000 {
pinctrl-names = "default";
pinctrl-0 = <&msp2_default_mode>;
status = "okay";
};
msp3: msp@80125000 {
......
......@@ -1443,14 +1443,14 @@ void edma_assign_channel_eventq(unsigned channel, enum dma_event_q eventq_no)
EXPORT_SYMBOL(edma_assign_channel_eventq);
static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
struct edma *edma_cc)
struct edma *edma_cc, int cc_id)
{
int i;
u32 value, cccfg;
s8 (*queue_priority_map)[2];
/* Decode the eDMA3 configuration from CCCFG register */
cccfg = edma_read(0, EDMA_CCCFG);
cccfg = edma_read(cc_id, EDMA_CCCFG);
value = GET_NUM_REGN(cccfg);
edma_cc->num_region = BIT(value);
......@@ -1464,7 +1464,8 @@ static int edma_setup_from_hw(struct device *dev, struct edma_soc_info *pdata,
value = GET_NUM_EVQUE(cccfg);
edma_cc->num_tc = value + 1;
dev_dbg(dev, "eDMA3 HW configuration (cccfg: 0x%08x):\n", cccfg);
dev_dbg(dev, "eDMA3 CC%d HW configuration (cccfg: 0x%08x):\n", cc_id,
cccfg);
dev_dbg(dev, "num_region: %u\n", edma_cc->num_region);
dev_dbg(dev, "num_channel: %u\n", edma_cc->num_channels);
dev_dbg(dev, "num_slot: %u\n", edma_cc->num_slots);
......@@ -1684,7 +1685,7 @@ static int edma_probe(struct platform_device *pdev)
return -ENOMEM;
/* Get eDMA3 configuration from IP */
ret = edma_setup_from_hw(dev, info[j], edma_cc[j]);
ret = edma_setup_from_hw(dev, info[j], edma_cc[j], j);
if (ret)
return ret;
......
......@@ -14,6 +14,7 @@
#include <linux/gpio.h>
#include <linux/of.h>
#include <linux/of_irq.h>
#include <linux/clk-provider.h>
#include <asm/setup.h>
#include <asm/irq.h>
......@@ -35,13 +36,21 @@ static void __init at91rm9200_dt_init_irq(void)
of_irq_init(irq_of_match);
}
static void __init at91rm9200_dt_timer_init(void)
{
#if defined(CONFIG_COMMON_CLK)
of_clk_init(NULL);
#endif
at91rm9200_timer_init();
}
static const char *at91rm9200_dt_board_compat[] __initdata = {
"atmel,at91rm9200",
NULL
};
DT_MACHINE_START(at91rm9200_dt, "Atmel AT91RM9200 (Device Tree)")
.init_time = at91rm9200_timer_init,
.init_time = at91rm9200_dt_timer_init,
.map_io = at91_map_io,
.handle_irq = at91_aic_handle_irq,
.init_early = at91rm9200_dt_initialize,
......
......@@ -1207,8 +1207,7 @@ int gpmc_cs_program_settings(int cs, struct gpmc_settings *p)
}
}
if ((p->wait_on_read || p->wait_on_write) &&
(p->wait_pin > gpmc_nr_waitpins)) {
if (p->wait_pin > gpmc_nr_waitpins) {
pr_err("%s: invalid wait-pin (%d)\n", __func__, p->wait_pin);
return -EINVAL;
}
......@@ -1288,7 +1287,7 @@ void gpmc_read_settings_dt(struct device_node *np, struct gpmc_settings *p)
p->wait_on_write = of_property_read_bool(np,
"gpmc,wait-on-write");
if (!p->wait_on_read && !p->wait_on_write)
pr_warn("%s: read/write wait monitoring not enabled!\n",
pr_debug("%s: rd/wr wait monitoring not enabled!\n",
__func__);
}
}
......
......@@ -586,6 +586,30 @@ static int arm_ccn_pmu_type_eq(u32 a, u32 b)
return 0;
}
static void arm_ccn_pmu_event_destroy(struct perf_event *event)
{
struct arm_ccn *ccn = pmu_to_arm_ccn(event->pmu);
struct hw_perf_event *hw = &event->hw;
if (hw->idx == CCN_IDX_PMU_CYCLE_COUNTER) {
clear_bit(CCN_IDX_PMU_CYCLE_COUNTER, ccn->dt.pmu_counters_mask);
} else {
struct arm_ccn_component *source =
ccn->dt.pmu_counters[hw->idx].source;
if (CCN_CONFIG_TYPE(event->attr.config) == CCN_TYPE_XP &&
CCN_CONFIG_EVENT(event->attr.config) ==
CCN_EVENT_WATCHPOINT)
clear_bit(hw->config_base, source->xp.dt_cmp_mask);
else
clear_bit(hw->config_base, source->pmu_events_mask);
clear_bit(hw->idx, ccn->dt.pmu_counters_mask);
}
ccn->dt.pmu_counters[hw->idx].source = NULL;
ccn->dt.pmu_counters[hw->idx].event = NULL;
}
static int arm_ccn_pmu_event_init(struct perf_event *event)
{
struct arm_ccn *ccn;
......@@ -599,6 +623,7 @@ static int arm_ccn_pmu_event_init(struct perf_event *event)
return -ENOENT;
ccn = pmu_to_arm_ccn(event->pmu);
event->destroy = arm_ccn_pmu_event_destroy;
if (hw->sample_period) {
dev_warn(ccn->dev, "Sampling not supported!\n");
......@@ -731,30 +756,6 @@ static int arm_ccn_pmu_event_init(struct perf_event *event)
return 0;
}
static void arm_ccn_pmu_event_free(struct perf_event *event)
{
struct arm_ccn *ccn = pmu_to_arm_ccn(event->pmu);
struct hw_perf_event *hw = &event->hw;
if (hw->idx == CCN_IDX_PMU_CYCLE_COUNTER) {
clear_bit(CCN_IDX_PMU_CYCLE_COUNTER, ccn->dt.pmu_counters_mask);
} else {
struct arm_ccn_component *source =
ccn->dt.pmu_counters[hw->idx].source;
if (CCN_CONFIG_TYPE(event->attr.config) == CCN_TYPE_XP &&
CCN_CONFIG_EVENT(event->attr.config) ==
CCN_EVENT_WATCHPOINT)
clear_bit(hw->config_base, source->xp.dt_cmp_mask);
else
clear_bit(hw->config_base, source->pmu_events_mask);
clear_bit(hw->idx, ccn->dt.pmu_counters_mask);
}
ccn->dt.pmu_counters[hw->idx].source = NULL;
ccn->dt.pmu_counters[hw->idx].event = NULL;
}
static u64 arm_ccn_pmu_read_counter(struct arm_ccn *ccn, int idx)
{
u64 res;
......@@ -1027,8 +1028,6 @@ static int arm_ccn_pmu_event_add(struct perf_event *event, int flags)
static void arm_ccn_pmu_event_del(struct perf_event *event, int flags)
{
arm_ccn_pmu_event_stop(event, PERF_EF_UPDATE);
arm_ccn_pmu_event_free(event);
}
static void arm_ccn_pmu_event_read(struct perf_event *event)
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment