Skip to content

L
linux
Commit 5b74a20d authored by Jakub Kicinski's avatar Jakub Kicinski Committed by David S. Miller
Browse files
Options

net: atm: remove support for Madge Horizon ATM devices 

This driver received nothing but automated fixes since git era begun.
Since it's using virt_to_bus it's unlikely to be used on any modern
platform.
Signed-off-by: default avatarJakub Kicinski <kuba@kernel.org>
Signed-off-by: default avatarDavid S. Miller <davem@davemloft.net>
parent 41c335c8
Show whitespace changes
Inline Side-by-side
Showing with 0 additions and 3372 deletions
arch/mips/configs/gpr_defconfig
View file @ 5b74a20d
......@@ -181,7 +181,6 @@ CONFIG_ATM_ENI=m
CONFIG_ATM_ZATM=m
CONFIG_ATM_NICSTAR=m
CONFIG_ATM_IDT77252=m
CONFIG_ATM_HORIZON=m
CONFIG_ATM_IA=m
CONFIG_ATM_FORE200E=m
CONFIG_ATM_HE=m
......
arch/mips/configs/mtx1_defconfig
View file @ 5b74a20d
......@@ -258,7 +258,6 @@ CONFIG_ATM_ENI=m
CONFIG_ATM_ZATM=m
CONFIG_ATM_NICSTAR=m
CONFIG_ATM_IDT77252=m
CONFIG_ATM_HORIZON=m
CONFIG_ATM_IA=m
CONFIG_ATM_FORE200E=m
CONFIG_ATM_HE=m
......
drivers/atm/Kconfig
View file @ 5b74a20d
......@@ -234,30 +234,6 @@ config ATM_IDT77252_USE_SUNI
depends on ATM_IDT77252
default y
config ATM_HORIZON
tristate "Madge Horizon [Ultra] (Collage PCI 25 and Collage PCI 155 Client)"
depends on PCI && VIRT_TO_BUS
help
This is a driver for the Horizon chipset ATM adapter cards once
produced by Madge Networks Ltd. Say Y (or M to compile as a module
named horizon) here if you have one of these cards.
config ATM_HORIZON_DEBUG
bool "Enable debugging messages"
depends on ATM_HORIZON
help
Somewhat useful debugging messages are available. The choice of
messages is controlled by a bitmap. This may be specified as a
module argument (kernel command line argument as well?), changed
dynamically using an ioctl (not yet) or changed by sending the
string "Dxxxx" to VCI 1023 (where x is a hex digit). See the file
<file:drivers/atm/horizon.h> for the meanings of the bits in the
mask.
When active, these messages can have a significant impact on the
speed of the driver, and the size of your syslog files! When
inactive, they will have only a modest impact on performance.
config ATM_IA
tristate "Interphase ATM PCI x575/x525/x531"
depends on PCI
......
drivers/atm/Makefile
View file @ 5b74a20d
......@@ -7,7 +7,6 @@ fore_200e-y := fore200e.o
obj-$(CONFIG_ATM_ZATM) += zatm.o uPD98402.o
obj-$(CONFIG_ATM_NICSTAR) += nicstar.o
obj-$(CONFIG_ATM_HORIZON) += horizon.o
obj-$(CONFIG_ATM_IA) += iphase.o suni.o
obj-$(CONFIG_ATM_FORE200E) += fore_200e.o
obj-$(CONFIG_ATM_ENI) += eni.o suni.o
......
drivers/atm/horizon.c deleted 100644 → 0
View file @ 41c335c8
// SPDX-License-Identifier: GPL-2.0-or-later
/*
Madge Horizon ATM Adapter driver.
Copyright (C) 1995-1999 Madge Networks Ltd.
*/
/*
IMPORTANT NOTE: Madge Networks no longer makes the adapters
supported by this driver and makes no commitment to maintain it.
*/
#include <linux/module.h>
#include <linux/kernel.h>
#include <linux/sched/signal.h>
#include <linux/mm.h>
#include <linux/pci.h>
#include <linux/errno.h>
#include <linux/atm.h>
#include <linux/atmdev.h>
#include <linux/sonet.h>
#include <linux/skbuff.h>
#include <linux/time.h>
#include <linux/delay.h>
#include <linux/uio.h>
#include <linux/init.h>
#include <linux/interrupt.h>
#include <linux/ioport.h>
#include <linux/wait.h>
#include <linux/slab.h>
#include <asm/io.h>
#include <linux/atomic.h>
#include <linux/uaccess.h>
#include <asm/string.h>
#include <asm/byteorder.h>
#include "horizon.h"
#define maintainer_string "Giuliano Procida at Madge Networks <gprocida@madge.com>"
#define description_string "Madge ATM Horizon [Ultra] driver"
#define version_string "1.2.1"
static inline void __init show_version (void) {
printk ("%s version %s\n", description_string, version_string);
}
/*
CREDITS
Driver and documentation by:
Chris Aston Madge Networks
Giuliano Procida Madge Networks
Simon Benham Madge Networks
Simon Johnson Madge Networks
Various Others Madge Networks
Some inspiration taken from other drivers by:
Alexandru Cucos UTBv
Kari Mettinen University of Helsinki
Werner Almesberger EPFL LRC
Theory of Operation
I Hardware, detection, initialisation and shutdown.
1. Supported Hardware
This driver should handle all variants of the PCI Madge ATM adapters
with the Horizon chipset. These are all PCI cards supporting PIO, BM
DMA and a form of MMIO (registers only, not internal RAM).
The driver is only known to work with SONET and UTP Horizon Ultra
cards at 155Mb/s. However, code is in place to deal with both the
original Horizon and 25Mb/s operation.
There are two revisions of the Horizon ASIC: the original and the
Ultra. Details of hardware bugs are in section III.
The ASIC version can be distinguished by chip markings but is NOT
indicated by the PCI revision (all adapters seem to have PCI rev 1).
I believe that:
Horizon => Collage 25 PCI Adapter (UTP and STP)
Horizon Ultra => Collage 155 PCI Client (UTP or SONET)
Ambassador x => Collage 155 PCI Server (completely different)
Horizon (25Mb/s) is fitted with UTP and STP connectors. It seems to
have a Madge B154 plus glue logic serializer. I have also found a
really ancient version of this with slightly different glue. It
comes with the revision 0 (140-025-01) ASIC.
Horizon Ultra (155Mb/s) is fitted with either a Pulse Medialink
output (UTP) or an HP HFBR 5205 output (SONET). It has either
Madge's SAMBA framer or a SUNI-lite device (early versions). It
comes with the revision 1 (140-027-01) ASIC.
2. Detection
All Horizon-based cards present with the same PCI Vendor and Device
IDs. The standard Linux 2.2 PCI API is used to locate any cards and
to enable bus-mastering (with appropriate latency).
ATM_LAYER_STATUS in the control register distinguishes between the
two possible physical layers (25 and 155). It is not clear whether
the 155 cards can also operate at 25Mbps. We rely on the fact that a
card operates at 155 if and only if it has the newer Horizon Ultra
ASIC.
For 155 cards the two possible framers are probed for and then set
up for loop-timing.
3. Initialisation
The card is reset and then put into a known state. The physical
layer is configured for normal operation at the appropriate speed;
in the case of the 155 cards, the framer is initialised with
line-based timing; the internal RAM is zeroed and the allocation of
buffers for RX and TX is made; the Burnt In Address is read and
copied to the ATM ESI; various policy settings for RX (VPI bits,
unknown VCs, oam cells) are made. Ideally all policy items should be
configurable at module load (if not actually on-demand), however,
only the vpi vs vci bit allocation can be specified at insmod.
4. Shutdown
This is in response to module_cleaup. No VCs are in use and the card
should be idle; it is reset.
II Driver software (as it should be)
0. Traffic Parameters
The traffic classes (not an enumeration) are currently: ATM_NONE (no
traffic), ATM_UBR, ATM_CBR, ATM_VBR and ATM_ABR, ATM_ANYCLASS
(compatible with everything). Together with (perhaps only some of)
the following items they make up the traffic specification.
struct atm_trafprm {
unsigned char traffic_class; traffic class (ATM_UBR, ...)
int max_pcr; maximum PCR in cells per second
int pcr; desired PCR in cells per second
int min_pcr; minimum PCR in cells per second
int max_cdv; maximum CDV in microseconds
int max_sdu; maximum SDU in bytes
};
Note that these denote bandwidth available not bandwidth used; the
possibilities according to ATMF are:
Real Time (cdv and max CDT given)
CBR(pcr) pcr bandwidth always available
rtVBR(pcr,scr,mbs) scr bandwidth always available, up to pcr at mbs too
Non Real Time
nrtVBR(pcr,scr,mbs) scr bandwidth always available, up to pcr at mbs too
UBR()
ABR(mcr,pcr) mcr bandwidth always available, up to pcr (depending) too
mbs is max burst size (bucket)
pcr and scr have associated cdvt values
mcr is like scr but has no cdtv
cdtv may differ at each hop
Some of the above items are qos items (as opposed to traffic
parameters). We have nothing to do with qos. All except ABR can have
their traffic parameters converted to GCRA parameters. The GCRA may
be implemented as a (real-number) leaky bucket. The GCRA can be used
in complicated ways by switches and in simpler ways by end-stations.
It can be used both to filter incoming cells and shape out-going
cells.
ATM Linux actually supports:
ATM_NONE() (no traffic in this direction)
ATM_UBR(max_frame_size)
ATM_CBR(max/min_pcr, max_cdv, max_frame_size)
0 or ATM_MAX_PCR are used to indicate maximum available PCR
A traffic specification consists of the AAL type and separate
traffic specifications for either direction. In ATM Linux it is:
struct atm_qos {
struct atm_trafprm txtp;
struct atm_trafprm rxtp;
unsigned char aal;
};
AAL types are:
ATM_NO_AAL AAL not specified
ATM_AAL0 "raw" ATM cells
ATM_AAL1 AAL1 (CBR)
ATM_AAL2 AAL2 (VBR)
ATM_AAL34 AAL3/4 (data)
ATM_AAL5 AAL5 (data)
ATM_SAAL signaling AAL
The Horizon has support for AAL frame types: 0, 3/4 and 5. However,
it does not implement AAL 3/4 SAR and it has a different notion of
"raw cell" to ATM Linux's (48 bytes vs. 52 bytes) so neither are
supported by this driver.
The Horizon has limited support for ABR (including UBR), VBR and
CBR. Each TX channel has a bucket (containing up to 31 cell units)
and two timers (PCR and SCR) associated with it that can be used to
govern cell emissions and host notification (in the case of ABR this
is presumably so that RM cells may be emitted at appropriate times).
The timers may either be disabled or may be set to any of 240 values
(determined by the clock crystal, a fixed (?) per-device divider, a
configurable divider and a configurable timer preload value).
At the moment only UBR and CBR are supported by the driver. VBR will
be supported as soon as ATM for Linux supports it. ABR support is
very unlikely as RM cell handling is completely up to the driver.
1. TX (TX channel setup and TX transfer)
The TX half of the driver owns the TX Horizon registers. The TX
component in the IRQ handler is the BM completion handler. This can
only be entered when tx_busy is true (enforced by hardware). The
other TX component can only be entered when tx_busy is false
(enforced by driver). So TX is single-threaded.
Apart from a minor optimisation to not re-select the last channel,
the TX send component works as follows:
Atomic test and set tx_busy until we succeed; we should implement
some sort of timeout so that tx_busy will never be stuck at true.
If no TX channel is set up for this VC we wait for an idle one (if
necessary) and set it up.
At this point we have a TX channel ready for use. We wait for enough
buffers to become available then start a TX transmit (set the TX
descriptor, schedule transfer, exit).
The IRQ component handles TX completion (stats, free buffer, tx_busy
unset, exit). We also re-schedule further transfers for the same
frame if needed.
TX setup in more detail:
TX open is a nop, the relevant information is held in the hrz_vcc
(vcc->dev_data) structure and is "cached" on the card.
TX close gets the TX lock and clears the channel from the "cache".
2. RX (Data Available and RX transfer)
The RX half of the driver owns the RX registers. There are two RX
components in the IRQ handler: the data available handler deals with
fresh data that has arrived on the card, the BM completion handler
is very similar to the TX completion handler. The data available
handler grabs the rx_lock and it is only released once the data has
been discarded or completely transferred to the host. The BM
completion handler only runs when the lock is held; the data
available handler is locked out over the same period.
Data available on the card triggers an interrupt. If the data is not
suitable for our existing RX channels or we cannot allocate a buffer
it is flushed. Otherwise an RX receive is scheduled. Multiple RX
transfers may be scheduled for the same frame.
RX setup in more detail:
RX open...
RX close...
III Hardware Bugs
0. Byte vs Word addressing of adapter RAM.
A design feature; see the .h file (especially the memory map).
1. Bus Master Data Transfers (original Horizon only, fixed in Ultra)
The host must not start a transmit direction transfer at a
non-four-byte boundary in host memory. Instead the host should
perform a byte, or a two byte, or one byte followed by two byte
transfer in order to start the rest of the transfer on a four byte
boundary. RX is OK.
Simultaneous transmit and receive direction bus master transfers are
not allowed.
The simplest solution to these two is to always do PIO (never DMA)
in the TX direction on the original Horizon. More complicated
solutions are likely to hurt my brain.
2. Loss of buffer on close VC
When a VC is being closed, the buffer associated with it is not
returned to the pool. The host must store the reference to this
buffer and when opening a new VC then give it to that new VC.
The host intervention currently consists of stacking such a buffer
pointer at VC close and checking the stack at VC open.
3. Failure to close a VC
If a VC is currently receiving a frame then closing the VC may fail
and the frame continues to be received.
The solution is to make sure any received frames are flushed when
ready. This is currently done just before the solution to 2.
4. PCI bus (original Horizon only, fixed in Ultra)
Reading from the data port prior to initialisation will hang the PCI
bus. Just don't do that then! We don't.
IV To Do List
. Timer code may be broken.
. Allow users to specify buffer allocation split for TX and RX.
. Deal once and for all with buggy VC close.
. Handle interrupted and/or non-blocking operations.
. Change some macros to functions and move from .h to .c.
. Try to limit the number of TX frames each VC may have queued, in
order to reduce the chances of TX buffer exhaustion.
. Implement VBR (bucket and timers not understood) and ABR (need to
do RM cells manually); also no Linux support for either.
. Implement QoS changes on open VCs (involves extracting parts of VC open
and close into separate functions and using them to make changes).
*/
/********** globals **********/
static void do_housekeeping (struct timer_list *t);
static unsigned short debug = 0;
static unsigned short vpi_bits = 0;
static int max_tx_size = 9000;
static int max_rx_size = 9000;
static unsigned char pci_lat = 0;
/********** access functions **********/
/* Read / Write Horizon registers */
static inline void wr_regl (const hrz_dev * dev, unsigned char reg, u32 data) {
outl (cpu_to_le32 (data), dev->iobase + reg);
}
static inline u32 rd_regl (const hrz_dev * dev, unsigned char reg) {
return le32_to_cpu (inl (dev->iobase + reg));
}
static inline void wr_regw (const hrz_dev * dev, unsigned char reg, u16 data) {
outw (cpu_to_le16 (data), dev->iobase + reg);
}
static inline u16 rd_regw (const hrz_dev * dev, unsigned char reg) {
return le16_to_cpu (inw (dev->iobase + reg));
}
static inline void wrs_regb (const hrz_dev * dev, unsigned char reg, void * addr, u32 len) {
outsb (dev->iobase + reg, addr, len);
}
static inline void rds_regb (const hrz_dev * dev, unsigned char reg, void * addr, u32 len) {
insb (dev->iobase + reg, addr, len);
}
/* Read / Write to a given address in Horizon buffer memory.
Interrupts must be disabled between the address register and data
port accesses as these must form an atomic operation. */
static inline void wr_mem (const hrz_dev * dev, HDW * addr, u32 data) {
// wr_regl (dev, MEM_WR_ADDR_REG_OFF, (u32) addr);
wr_regl (dev, MEM_WR_ADDR_REG_OFF, (addr - (HDW *) 0) * sizeof(HDW));
wr_regl (dev, MEMORY_PORT_OFF, data);
}
static inline u32 rd_mem (const hrz_dev * dev, HDW * addr) {
// wr_regl (dev, MEM_RD_ADDR_REG_OFF, (u32) addr);
wr_regl (dev, MEM_RD_ADDR_REG_OFF, (addr - (HDW *) 0) * sizeof(HDW));
return rd_regl (dev, MEMORY_PORT_OFF);
}
static inline void wr_framer (const hrz_dev * dev, u32 addr, u32 data) {
wr_regl (dev, MEM_WR_ADDR_REG_OFF, (u32) addr | 0x80000000);
wr_regl (dev, MEMORY_PORT_OFF, data);
}
static inline u32 rd_framer (const hrz_dev * dev, u32 addr) {
wr_regl (dev, MEM_RD_ADDR_REG_OFF, (u32) addr | 0x80000000);
return rd_regl (dev, MEMORY_PORT_OFF);
}
/********** specialised access functions **********/
/* RX */
static inline void FLUSH_RX_CHANNEL (hrz_dev * dev, u16 channel) {
wr_regw (dev, RX_CHANNEL_PORT_OFF, FLUSH_CHANNEL | channel);
return;
}
static void WAIT_FLUSH_RX_COMPLETE (hrz_dev * dev) {
while (rd_regw (dev, RX_CHANNEL_PORT_OFF) & FLUSH_CHANNEL)
;
return;
}
static inline void SELECT_RX_CHANNEL (hrz_dev * dev, u16 channel) {
wr_regw (dev, RX_CHANNEL_PORT_OFF, channel);
return;
}
static void WAIT_UPDATE_COMPLETE (hrz_dev * dev) {
while (rd_regw (dev, RX_CHANNEL_PORT_OFF) & RX_CHANNEL_UPDATE_IN_PROGRESS)
;
return;
}
/* TX */
static inline void SELECT_TX_CHANNEL (hrz_dev * dev, u16 tx_channel) {
wr_regl (dev, TX_CHANNEL_PORT_OFF, tx_channel);
return;
}
/* Update or query one configuration parameter of a particular channel. */
static inline void update_tx_channel_config (hrz_dev * dev, short chan, u8 mode, u16 value) {
wr_regw (dev, TX_CHANNEL_CONFIG_COMMAND_OFF,
chan * TX_CHANNEL_CONFIG_MULT | mode);
wr_regw (dev, TX_CHANNEL_CONFIG_DATA_OFF, value);
return;
}
/********** dump functions **********/
static inline void dump_skb (char * prefix, unsigned int vc, struct sk_buff * skb) {
#ifdef DEBUG_HORIZON
unsigned int i;
unsigned char * data = skb->data;
PRINTDB (DBG_DATA, "%s(%u) ", prefix, vc);
for (i=0; i<skb->len && i < 256;i++)
PRINTDM (DBG_DATA, "%02x ", data[i]);
PRINTDE (DBG_DATA,"");
#else
(void) prefix;
(void) vc;
(void) skb;
#endif
return;
}
static inline void dump_regs (hrz_dev * dev) {
#ifdef DEBUG_HORIZON
PRINTD (DBG_REGS, "CONTROL 0: %#x", rd_regl (dev, CONTROL_0_REG));
PRINTD (DBG_REGS, "RX CONFIG: %#x", rd_regw (dev, RX_CONFIG_OFF));
PRINTD (DBG_REGS, "TX CONFIG: %#x", rd_regw (dev, TX_CONFIG_OFF));
PRINTD (DBG_REGS, "TX STATUS: %#x", rd_regw (dev, TX_STATUS_OFF));
PRINTD (DBG_REGS, "IRQ ENBLE: %#x", rd_regl (dev, INT_ENABLE_REG_OFF));
PRINTD (DBG_REGS, "IRQ SORCE: %#x", rd_regl (dev, INT_SOURCE_REG_OFF));
#else
(void) dev;
#endif
return;
}
static inline void dump_framer (hrz_dev * dev) {
#ifdef DEBUG_HORIZON
unsigned int i;
PRINTDB (DBG_REGS, "framer registers:");
for (i = 0; i < 0x10; ++i)
PRINTDM (DBG_REGS, " %02x", rd_framer (dev, i));
PRINTDE (DBG_REGS,"");
#else
(void) dev;
#endif
return;
}
/********** VPI/VCI <-> (RX) channel conversions **********/
/* RX channels are 10 bit integers, these fns are quite paranoid */
static inline int vpivci_to_channel (u16 * channel, const short vpi, const int vci) {
unsigned short vci_bits = 10 - vpi_bits;
if (0 <= vpi && vpi < 1<<vpi_bits && 0 <= vci && vci < 1<<vci_bits) {
*channel = vpi<<vci_bits | vci;
return *channel ? 0 : -EINVAL;
}
return -EINVAL;
}
/********** decode RX queue entries **********/
static inline u16 rx_q_entry_to_length (u32 x) {
return x & RX_Q_ENTRY_LENGTH_MASK;
}
static inline u16 rx_q_entry_to_rx_channel (u32 x) {
return (x>>RX_Q_ENTRY_CHANNEL_SHIFT) & RX_CHANNEL_MASK;
}
/* Cell Transmit Rate Values
*
* the cell transmit rate (cells per sec) can be set to a variety of
* different values by specifying two parameters: a timer preload from
* 1 to 16 (stored as 0 to 15) and a clock divider (2 to the power of
* an exponent from 0 to 14; the special value 15 disables the timer).
*
* cellrate = baserate / (preload * 2^divider)
*
* The maximum cell rate that can be specified is therefore just the
* base rate. Halving the preload is equivalent to adding 1 to the
* divider and so values 1 to 8 of the preload are redundant except
* in the case of a maximal divider (14).
*
* Given a desired cell rate, an algorithm to determine the preload
* and divider is:
*
* a) x = baserate / cellrate, want p * 2^d = x (as far as possible)
* b) if x > 16 * 2^14 then set p = 16, d = 14 (min rate), done
* if x <= 16 then set p = x, d = 0 (high rates), done
* c) now have 16 < x <= 2^18, or 1 < x/16 <= 2^14 and we want to
* know n such that 2^(n-1) < x/16 <= 2^n, so slide a bit until
* we find the range (n will be between 1 and 14), set d = n
* d) Also have 8 < x/2^n <= 16, so set p nearest x/2^n
*
* The algorithm used below is a minor variant of the above.
*
* The base rate is derived from the oscillator frequency (Hz) using a
* fixed divider:
*
* baserate = freq / 32 in the case of some Unknown Card
* baserate = freq / 8 in the case of the Horizon 25
* baserate = freq / 8 in the case of the Horizon Ultra 155
*
* The Horizon cards have oscillators and base rates as follows:
*
* Card Oscillator Base Rate
* Unknown Card 33 MHz 1.03125 MHz (33 MHz = PCI freq)
* Horizon 25 32 MHz 4 MHz
* Horizon Ultra 155 40 MHz 5 MHz
*
* The following defines give the base rates in Hz. These were
* previously a factor of 100 larger, no doubt someone was using
* cps*100.
*/
#define BR_UKN 1031250l
#define BR_HRZ 4000000l
#define BR_ULT 5000000l
// d is an exponent
#define CR_MIND 0
#define CR_MAXD 14
// p ranges from 1 to a power of 2
#define CR_MAXPEXP 4
static int make_rate (const hrz_dev * dev, u32 c, rounding r,
u16 * bits, unsigned int * actual)
{
// note: rounding the rate down means rounding 'p' up
const unsigned long br = test_bit(ultra, &dev->flags) ? BR_ULT : BR_HRZ;
u32 div = CR_MIND;
u32 pre;
// br_exp and br_man are used to avoid overflowing (c*maxp*2^d) in
// the tests below. We could think harder about exact possibilities
// of failure...
unsigned long br_man = br;
unsigned int br_exp = 0;
PRINTD (DBG_QOS|DBG_FLOW, "make_rate b=%lu, c=%u, %s", br, c,
r == round_up ? "up" : r == round_down ? "down" : "nearest");
// avoid div by zero
if (!c) {
PRINTD (DBG_QOS|DBG_ERR, "zero rate is not allowed!");
return -EINVAL;
}
while (br_exp < CR_MAXPEXP + CR_MIND && (br_man % 2 == 0)) {
br_man = br_man >> 1;
++br_exp;
}
// (br >>br_exp) <<br_exp == br and
// br_exp <= CR_MAXPEXP+CR_MIND
if (br_man <= (c << (CR_MAXPEXP+CR_MIND-br_exp))) {
// Equivalent to: B <= (c << (MAXPEXP+MIND))
// take care of rounding
switch (r) {
case round_down:
pre = DIV_ROUND_UP(br, c<<div);
// but p must be non-zero
if (!pre)
pre = 1;
break;
case round_nearest:
pre = DIV_ROUND_CLOSEST(br, c<<div);
// but p must be non-zero
if (!pre)
pre = 1;
break;
default: /* round_up */
pre = br/(c<<div);
// but p must be non-zero
if (!pre)
return -EINVAL;
}
PRINTD (DBG_QOS, "A: p=%u, d=%u", pre, div);
goto got_it;
}
// at this point we have
// d == MIND and (c << (MAXPEXP+MIND)) < B
while (div < CR_MAXD) {
div++;
if (br_man <= (c << (CR_MAXPEXP+div-br_exp))) {
// Equivalent to: B <= (c << (MAXPEXP+d))
// c << (MAXPEXP+d-1) < B <= c << (MAXPEXP+d)
// 1 << (MAXPEXP-1) < B/2^d/c <= 1 << MAXPEXP
// MAXP/2 < B/c2^d <= MAXP
// take care of rounding
switch (r) {
case round_down:
pre = DIV_ROUND_UP(br, c<<div);
break;
case round_nearest:
pre = DIV_ROUND_CLOSEST(br, c<<div);
break;
default: /* round_up */
pre = br/(c<<div);
}
PRINTD (DBG_QOS, "B: p=%u, d=%u", pre, div);
goto got_it;
}
}
// at this point we have
// d == MAXD and (c << (MAXPEXP+MAXD)) < B
// but we cannot go any higher
// take care of rounding
if (r == round_down)
return -EINVAL;
pre = 1 << CR_MAXPEXP;
PRINTD (DBG_QOS, "C: p=%u, d=%u", pre, div);
got_it:
// paranoia
if (div > CR_MAXD || (!pre) || pre > 1<<CR_MAXPEXP) {
PRINTD (DBG_QOS, "set_cr internal failure: d=%u p=%u",
div, pre);
return -EINVAL;
} else {
if (bits)
*bits = (div<<CLOCK_SELECT_SHIFT) | (pre-1);
if (actual) {
*actual = DIV_ROUND_UP(br, pre<<div);
PRINTD (DBG_QOS, "actual rate: %u", *actual);
}
return 0;
}
}
static int make_rate_with_tolerance (const hrz_dev * dev, u32 c, rounding r, unsigned int tol,
u16 * bit_pattern, unsigned int * actual) {
unsigned int my_actual;
PRINTD (DBG_QOS|DBG_FLOW, "make_rate_with_tolerance c=%u, %s, tol=%u",
c, (r == round_up) ? "up" : (r == round_down) ? "down" : "nearest", tol);
if (!actual)
// actual rate is not returned
actual = &my_actual;
if (make_rate (dev, c, round_nearest, bit_pattern, actual))
// should never happen as round_nearest always succeeds
return -1;
if (c - tol <= *actual && *actual <= c + tol)
// within tolerance
return 0;
else
// intolerant, try rounding instead
return make_rate (dev, c, r, bit_pattern, actual);
}
/********** Listen on a VC **********/
static int hrz_open_rx (hrz_dev * dev, u16 channel) {
// is there any guarantee that we don't get two simulataneous
// identical calls of this function from different processes? yes
// rate_lock
unsigned long flags;
u32 channel_type; // u16?
u16 buf_ptr = RX_CHANNEL_IDLE;
rx_ch_desc * rx_desc = &memmap->rx_descs[channel];
PRINTD (DBG_FLOW, "hrz_open_rx %x", channel);
spin_lock_irqsave (&dev->mem_lock, flags);
channel_type = rd_mem (dev, &rx_desc->wr_buf_type) & BUFFER_PTR_MASK;
spin_unlock_irqrestore (&dev->mem_lock, flags);
// very serious error, should never occur
if (channel_type != RX_CHANNEL_DISABLED) {
PRINTD (DBG_ERR|DBG_VCC, "RX channel for VC already open");
return -EBUSY; // clean up?
}
// Give back spare buffer
if (dev->noof_spare_buffers) {
buf_ptr = dev->spare_buffers[--dev->noof_spare_buffers];
PRINTD (DBG_VCC, "using a spare buffer: %u", buf_ptr);
// should never occur
if (buf_ptr == RX_CHANNEL_DISABLED || buf_ptr == RX_CHANNEL_IDLE) {
// but easy to recover from
PRINTD (DBG_ERR|DBG_VCC, "bad spare buffer pointer, using IDLE");
buf_ptr = RX_CHANNEL_IDLE;
}
} else {
PRINTD (DBG_VCC, "using IDLE buffer pointer");
}
// Channel is currently disabled so change its status to idle
// do we really need to save the flags again?
spin_lock_irqsave (&dev->mem_lock, flags);
wr_mem (dev, &rx_desc->wr_buf_type,
buf_ptr | CHANNEL_TYPE_AAL5 | FIRST_CELL_OF_AAL5_FRAME);
if (buf_ptr != RX_CHANNEL_IDLE)
wr_mem (dev, &rx_desc->rd_buf_type, buf_ptr);
spin_unlock_irqrestore (&dev->mem_lock, flags);
// rxer->rate = make_rate (qos->peak_cells);
PRINTD (DBG_FLOW, "hrz_open_rx ok");
return 0;
}
#if 0
/********** change vc rate for a given vc **********/
static void hrz_change_vc_qos (ATM_RXER * rxer, MAAL_QOS * qos) {
rxer->rate = make_rate (qos->peak_cells);
}
#endif
/********** free an skb (as per ATM device driver documentation) **********/
static void hrz_kfree_skb (struct sk_buff * skb) {
if (ATM_SKB(skb)->vcc->pop) {
ATM_SKB(skb)->vcc->pop (ATM_SKB(skb)->vcc, skb);
} else {
dev_kfree_skb_any (skb);
}
}
/********** cancel listen on a VC **********/
static void hrz_close_rx (hrz_dev * dev, u16 vc) {
unsigned long flags;
u32 value;
u32 r1, r2;
rx_ch_desc * rx_desc = &memmap->rx_descs[vc];
int was_idle = 0;
spin_lock_irqsave (&dev->mem_lock, flags);
value = rd_mem (dev, &rx_desc->wr_buf_type) & BUFFER_PTR_MASK;
spin_unlock_irqrestore (&dev->mem_lock, flags);
if (value == RX_CHANNEL_DISABLED) {
// I suppose this could happen once we deal with _NONE traffic properly
PRINTD (DBG_VCC, "closing VC: RX channel %u already disabled", vc);
return;
}
if (value == RX_CHANNEL_IDLE)
was_idle = 1;
spin_lock_irqsave (&dev->mem_lock, flags);
for (;;) {
wr_mem (dev, &rx_desc->wr_buf_type, RX_CHANNEL_DISABLED);
if ((rd_mem (dev, &rx_desc->wr_buf_type) & BUFFER_PTR_MASK) == RX_CHANNEL_DISABLED)
break;
was_idle = 0;
}
if (was_idle) {
spin_unlock_irqrestore (&dev->mem_lock, flags);
return;
}
WAIT_FLUSH_RX_COMPLETE(dev);
// XXX Is this all really necessary? We can rely on the rx_data_av
// handler to discard frames that remain queued for delivery. If the
// worry is that immediately reopening the channel (perhaps by a
// different process) may cause some data to be mis-delivered then
// there may still be a simpler solution (such as busy-waiting on
// rx_busy once the channel is disabled or before a new one is
// opened - does this leave any holes?). Arguably setting up and
// tearing down the TX and RX halves of each virtual circuit could
// most safely be done within ?x_busy protected regions.
// OK, current changes are that Simon's marker is disabled and we DO
// look for NULL rxer elsewhere. The code here seems flush frames
// and then remember the last dead cell belonging to the channel
// just disabled - the cell gets relinked at the next vc_open.
// However, when all VCs are closed or only a few opened there are a
// handful of buffers that are unusable.
// Does anyone feel like documenting spare_buffers properly?
// Does anyone feel like fixing this in a nicer way?
// Flush any data which is left in the channel
for (;;) {
// Change the rx channel port to something different to the RX
// channel we are trying to close to force Horizon to flush the rx
// channel read and write pointers.
u16 other = vc^(RX_CHANS/2);
SELECT_RX_CHANNEL (dev, other);
WAIT_UPDATE_COMPLETE (dev);
r1 = rd_mem (dev, &rx_desc->rd_buf_type);
// Select this RX channel. Flush doesn't seem to work unless we
// select an RX channel before hand
SELECT_RX_CHANNEL (dev, vc);
WAIT_UPDATE_COMPLETE (dev);
// Attempt to flush a frame on this RX channel
FLUSH_RX_CHANNEL (dev, vc);
WAIT_FLUSH_RX_COMPLETE (dev);
// Force Horizon to flush rx channel read and write pointers as before
SELECT_RX_CHANNEL (dev, other);
WAIT_UPDATE_COMPLETE (dev);
r2 = rd_mem (dev, &rx_desc->rd_buf_type);
PRINTD (DBG_VCC|DBG_RX, "r1 = %u, r2 = %u", r1, r2);
if (r1 == r2) {
dev->spare_buffers[dev->noof_spare_buffers++] = (u16)r1;
break;
}
}
#if 0
{
rx_q_entry * wr_ptr = &memmap->rx_q_entries[rd_regw (dev, RX_QUEUE_WR_PTR_OFF)];
rx_q_entry * rd_ptr = dev->rx_q_entry;
PRINTD (DBG_VCC|DBG_RX, "rd_ptr = %u, wr_ptr = %u", rd_ptr, wr_ptr);
while (rd_ptr != wr_ptr) {
u32 x = rd_mem (dev, (HDW *) rd_ptr);
if (vc == rx_q_entry_to_rx_channel (x)) {
x |= SIMONS_DODGEY_MARKER;
PRINTD (DBG_RX|DBG_VCC|DBG_WARN, "marking a frame as dodgey");
wr_mem (dev, (HDW *) rd_ptr, x);
}
if (rd_ptr == dev->rx_q_wrap)
rd_ptr = dev->rx_q_reset;
else
rd_ptr++;
}
}
#endif
spin_unlock_irqrestore (&dev->mem_lock, flags);
return;
}
/********** schedule RX transfers **********/
// Note on tail recursion: a GCC developer said that it is not likely
// to be fixed soon, so do not define TAILRECUSRIONWORKS unless you
// are sure it does as you may otherwise overflow the kernel stack.
// giving this fn a return value would help GCC, allegedly
static void rx_schedule (hrz_dev * dev, int irq) {
unsigned int rx_bytes;
int pio_instead = 0;
#ifndef TAILRECURSIONWORKS
pio_instead = 1;
while (pio_instead) {
#endif
// bytes waiting for RX transfer
rx_bytes = dev->rx_bytes;
#if 0
spin_count = 0;
while (rd_regl (dev, MASTER_RX_COUNT_REG_OFF)) {
PRINTD (DBG_RX|DBG_WARN, "RX error: other PCI Bus Master RX still in progress!");
if (++spin_count > 10) {
PRINTD (DBG_RX|DBG_ERR, "spun out waiting PCI Bus Master RX completion");
wr_regl (dev, MASTER_RX_COUNT_REG_OFF, 0);
clear_bit (rx_busy, &dev->flags);
hrz_kfree_skb (dev->rx_skb);
return;
}
}
#endif
// this code follows the TX code but (at the moment) there is only
// one region - the skb itself. I don't know if this will change,
// but it doesn't hurt to have the code here, disabled.
if (rx_bytes) {
// start next transfer within same region
if (rx_bytes <= MAX_PIO_COUNT) {
PRINTD (DBG_RX|DBG_BUS, "(pio)");
pio_instead = 1;
}
if (rx_bytes <= MAX_TRANSFER_COUNT) {
PRINTD (DBG_RX|DBG_BUS, "(simple or last multi)");
dev->rx_bytes = 0;
} else {
PRINTD (DBG_RX|DBG_BUS, "(continuing multi)");
dev->rx_bytes = rx_bytes - MAX_TRANSFER_COUNT;
rx_bytes = MAX_TRANSFER_COUNT;
}
} else {
// rx_bytes == 0 -- we're between regions
// regions remaining to transfer
#if 0
unsigned int rx_regions = dev->rx_regions;
#else
unsigned int rx_regions = 0;
#endif
if (rx_regions) {
#if 0
// start a new region
dev->rx_addr = dev->rx_iovec->iov_base;
rx_bytes = dev->rx_iovec->iov_len;
++dev->rx_iovec;
dev->rx_regions = rx_regions - 1;
if (rx_bytes <= MAX_PIO_COUNT) {
PRINTD (DBG_RX|DBG_BUS, "(pio)");
pio_instead = 1;
}
if (rx_bytes <= MAX_TRANSFER_COUNT) {
PRINTD (DBG_RX|DBG_BUS, "(full region)");
dev->rx_bytes = 0;
} else {
PRINTD (DBG_RX|DBG_BUS, "(start multi region)");
dev->rx_bytes = rx_bytes - MAX_TRANSFER_COUNT;
rx_bytes = MAX_TRANSFER_COUNT;
}
#endif
} else {
// rx_regions == 0
// that's all folks - end of frame
struct sk_buff * skb = dev->rx_skb;
// dev->rx_iovec = 0;
FLUSH_RX_CHANNEL (dev, dev->rx_channel);
dump_skb ("<<<", dev->rx_channel, skb);
PRINTD (DBG_RX|DBG_SKB, "push %p %u", skb->data, skb->len);
{
struct atm_vcc * vcc = ATM_SKB(skb)->vcc;
// VC layer stats
atomic_inc(&vcc->stats->rx);
__net_timestamp(skb);
// end of our responsibility
vcc->push (vcc, skb);
}
}
}
// note: writing RX_COUNT clears any interrupt condition
if (rx_bytes) {
if (pio_instead) {
if (irq)
wr_regl (dev, MASTER_RX_COUNT_REG_OFF, 0);
rds_regb (dev, DATA_PORT_OFF, dev->rx_addr, rx_bytes);
} else {
wr_regl (dev, MASTER_RX_ADDR_REG_OFF, virt_to_bus (dev->rx_addr));
wr_regl (dev, MASTER_RX_COUNT_REG_OFF, rx_bytes);
}
dev->rx_addr += rx_bytes;
} else {
if (irq)
wr_regl (dev, MASTER_RX_COUNT_REG_OFF, 0);
// allow another RX thread to start
YELLOW_LED_ON(dev);
clear_bit (rx_busy, &dev->flags);
PRINTD (DBG_RX, "cleared rx_busy for dev %p", dev);
}
#ifdef TAILRECURSIONWORKS
// and we all bless optimised tail calls
if (pio_instead)
return rx_schedule (dev, 0);
return;
#else
// grrrrrrr!
irq = 0;
}
return;
#endif
}
/********** handle RX bus master complete events **********/
static void rx_bus_master_complete_handler (hrz_dev * dev) {
if (test_bit (rx_busy, &dev->flags)) {
rx_schedule (dev, 1);
} else {
PRINTD (DBG_RX|DBG_ERR, "unexpected RX bus master completion");
// clear interrupt condition on adapter
wr_regl (dev, MASTER_RX_COUNT_REG_OFF, 0);
}
return;
}
/********** (queue to) become the next TX thread **********/
static int tx_hold (hrz_dev * dev) {
PRINTD (DBG_TX, "sleeping at tx lock %p %lu", dev, dev->flags);
wait_event_interruptible(dev->tx_queue, (!test_and_set_bit(tx_busy, &dev->flags)));
PRINTD (DBG_TX, "woken at tx lock %p %lu", dev, dev->flags);
if (signal_pending (current))
return -1;
PRINTD (DBG_TX, "set tx_busy for dev %p", dev);
return 0;
}
/********** allow another TX thread to start **********/
static inline void tx_release (hrz_dev * dev) {
clear_bit (tx_busy, &dev->flags);
PRINTD (DBG_TX, "cleared tx_busy for dev %p", dev);
wake_up_interruptible (&dev->tx_queue);
}
/********** schedule TX transfers **********/
static void tx_schedule (hrz_dev * const dev, int irq) {
unsigned int tx_bytes;
int append_desc = 0;
int pio_instead = 0;
#ifndef TAILRECURSIONWORKS
pio_instead = 1;
while (pio_instead) {
#endif
// bytes in current region waiting for TX transfer
tx_bytes = dev->tx_bytes;
#if 0
spin_count = 0;
while (rd_regl (dev, MASTER_TX_COUNT_REG_OFF)) {
PRINTD (DBG_TX|DBG_WARN, "TX error: other PCI Bus Master TX still in progress!");
if (++spin_count > 10) {
PRINTD (DBG_TX|DBG_ERR, "spun out waiting PCI Bus Master TX completion");
wr_regl (dev, MASTER_TX_COUNT_REG_OFF, 0);
tx_release (dev);
hrz_kfree_skb (dev->tx_skb);
return;
}
}
#endif
if (tx_bytes) {
// start next transfer within same region
if (!test_bit (ultra, &dev->flags) || tx_bytes <= MAX_PIO_COUNT) {
PRINTD (DBG_TX|DBG_BUS, "(pio)");
pio_instead = 1;
}
if (tx_bytes <= MAX_TRANSFER_COUNT) {
PRINTD (DBG_TX|DBG_BUS, "(simple or last multi)");
if (!dev->tx_iovec) {
// end of last region
append_desc = 1;
}
dev->tx_bytes = 0;
} else {
PRINTD (DBG_TX|DBG_BUS, "(continuing multi)");
dev->tx_bytes = tx_bytes - MAX_TRANSFER_COUNT;
tx_bytes = MAX_TRANSFER_COUNT;
}
} else {
// tx_bytes == 0 -- we're between regions
// regions remaining to transfer
unsigned int tx_regions = dev->tx_regions;
if (tx_regions) {
// start a new region
dev->tx_addr = dev->tx_iovec->iov_base;
tx_bytes = dev->tx_iovec->iov_len;
++dev->tx_iovec;
dev->tx_regions = tx_regions - 1;
if (!test_bit (ultra, &dev->flags) || tx_bytes <= MAX_PIO_COUNT) {
PRINTD (DBG_TX|DBG_BUS, "(pio)");
pio_instead = 1;
}
if (tx_bytes <= MAX_TRANSFER_COUNT) {
PRINTD (DBG_TX|DBG_BUS, "(full region)");
dev->tx_bytes = 0;
} else {
PRINTD (DBG_TX|DBG_BUS, "(start multi region)");
dev->tx_bytes = tx_bytes - MAX_TRANSFER_COUNT;
tx_bytes = MAX_TRANSFER_COUNT;
}
} else {
// tx_regions == 0
// that's all folks - end of frame
struct sk_buff * skb = dev->tx_skb;
dev->tx_iovec = NULL;
// VC layer stats
atomic_inc(&ATM_SKB(skb)->vcc->stats->tx);
// free the skb
hrz_kfree_skb (skb);
}
}
// note: writing TX_COUNT clears any interrupt condition
if (tx_bytes) {
if (pio_instead) {
if (irq)
wr_regl (dev, MASTER_TX_COUNT_REG_OFF, 0);
wrs_regb (dev, DATA_PORT_OFF, dev->tx_addr, tx_bytes);
if (append_desc)
wr_regl (dev, TX_DESCRIPTOR_PORT_OFF, cpu_to_be32 (dev->tx_skb->len));
} else {
wr_regl (dev, MASTER_TX_ADDR_REG_OFF, virt_to_bus (dev->tx_addr));
if (append_desc)
wr_regl (dev, TX_DESCRIPTOR_REG_OFF, cpu_to_be32 (dev->tx_skb->len));
wr_regl (dev, MASTER_TX_COUNT_REG_OFF,
append_desc
? tx_bytes | MASTER_TX_AUTO_APPEND_DESC
: tx_bytes);
}
dev->tx_addr += tx_bytes;
} else {
if (irq)
wr_regl (dev, MASTER_TX_COUNT_REG_OFF, 0);
YELLOW_LED_ON(dev);
tx_release (dev);
}
#ifdef TAILRECURSIONWORKS
// and we all bless optimised tail calls
if (pio_instead)
return tx_schedule (dev, 0);
return;
#else
// grrrrrrr!
irq = 0;
}
return;
#endif
}
/********** handle TX bus master complete events **********/
static void tx_bus_master_complete_handler (hrz_dev * dev) {
if (test_bit (tx_busy, &dev->flags)) {
tx_schedule (dev, 1);
} else {
PRINTD (DBG_TX|DBG_ERR, "unexpected TX bus master completion");
// clear interrupt condition on adapter
wr_regl (dev, MASTER_TX_COUNT_REG_OFF, 0);
}
return;
}
/********** move RX Q pointer to next item in circular buffer **********/
// called only from IRQ sub-handler
static u32 rx_queue_entry_next (hrz_dev * dev) {
u32 rx_queue_entry;
spin_lock (&dev->mem_lock);
rx_queue_entry = rd_mem (dev, &dev->rx_q_entry->entry);
if (dev->rx_q_entry == dev->rx_q_wrap)
dev->rx_q_entry = dev->rx_q_reset;
else
dev->rx_q_entry++;
wr_regw (dev, RX_QUEUE_RD_PTR_OFF, dev->rx_q_entry - dev->rx_q_reset);
spin_unlock (&dev->mem_lock);
return rx_queue_entry;
}
/********** handle RX data received by device **********/
// called from IRQ handler
static void rx_data_av_handler (hrz_dev * dev) {
u32 rx_queue_entry;
u32 rx_queue_entry_flags;
u16 rx_len;
u16 rx_channel;
PRINTD (DBG_FLOW, "hrz_data_av_handler");
// try to grab rx lock (not possible during RX bus mastering)
if (test_and_set_bit (rx_busy, &dev->flags)) {
PRINTD (DBG_RX, "locked out of rx lock");
return;
}
PRINTD (DBG_RX, "set rx_busy for dev %p", dev);
// lock is cleared if we fail now, o/w after bus master completion
YELLOW_LED_OFF(dev);
rx_queue_entry = rx_queue_entry_next (dev);
rx_len = rx_q_entry_to_length (rx_queue_entry);
rx_channel = rx_q_entry_to_rx_channel (rx_queue_entry);
WAIT_FLUSH_RX_COMPLETE (dev);
SELECT_RX_CHANNEL (dev, rx_channel);
PRINTD (DBG_RX, "rx_queue_entry is: %#x", rx_queue_entry);
rx_queue_entry_flags = rx_queue_entry & (RX_CRC_32_OK|RX_COMPLETE_FRAME|SIMONS_DODGEY_MARKER);
if (!rx_len) {
// (at least) bus-mastering breaks if we try to handle a
// zero-length frame, besides AAL5 does not support them
PRINTK (KERN_ERR, "zero-length frame!");
rx_queue_entry_flags &= ~RX_COMPLETE_FRAME;
}
if (rx_queue_entry_flags & SIMONS_DODGEY_MARKER) {
PRINTD (DBG_RX|DBG_ERR, "Simon's marker detected!");
}
if (rx_queue_entry_flags == (RX_CRC_32_OK | RX_COMPLETE_FRAME)) {
struct atm_vcc * atm_vcc;
PRINTD (DBG_RX, "got a frame on rx_channel %x len %u", rx_channel, rx_len);
atm_vcc = dev->rxer[rx_channel];
// if no vcc is assigned to this channel, we should drop the frame
// (is this what SIMONS etc. was trying to achieve?)
if (atm_vcc) {
if (atm_vcc->qos.rxtp.traffic_class != ATM_NONE) {
if (rx_len <= atm_vcc->qos.rxtp.max_sdu) {
struct sk_buff * skb = atm_alloc_charge (atm_vcc, rx_len, GFP_ATOMIC);
if (skb) {
// remember this so we can push it later
dev->rx_skb = skb;
// remember this so we can flush it later
dev->rx_channel = rx_channel;
// prepare socket buffer
skb_put (skb, rx_len);
ATM_SKB(skb)->vcc = atm_vcc;
// simple transfer
// dev->rx_regions = 0;
// dev->rx_iovec = 0;
dev->rx_bytes = rx_len;
dev->rx_addr = skb->data;
PRINTD (DBG_RX, "RX start simple transfer (addr %p, len %d)",
skb->data, rx_len);
// do the business
rx_schedule (dev, 0);
return;
} else {
PRINTD (DBG_SKB|DBG_WARN, "failed to get skb");
}
} else {
PRINTK (KERN_INFO, "frame received on TX-only VC %x", rx_channel);
// do we count this?
}
} else {
PRINTK (KERN_WARNING, "dropped over-size frame");
// do we count this?
}
} else {
PRINTD (DBG_WARN|DBG_VCC|DBG_RX, "no VCC for this frame (VC closed)");
// do we count this?
}
} else {
// Wait update complete ? SPONG
}
// RX was aborted
YELLOW_LED_ON(dev);
FLUSH_RX_CHANNEL (dev,rx_channel);
clear_bit (rx_busy, &dev->flags);
return;
}
/********** interrupt handler **********/
static irqreturn_t interrupt_handler(int irq, void *dev_id)
{
hrz_dev *dev = dev_id;
u32 int_source;
unsigned int irq_ok;
PRINTD (DBG_FLOW, "interrupt_handler: %p", dev_id);
// definitely for us
irq_ok = 0;
while ((int_source = rd_regl (dev, INT_SOURCE_REG_OFF)
& INTERESTING_INTERRUPTS)) {
// In the interests of fairness, the handlers below are
// called in sequence and without immediate return to the head of
// the while loop. This is only of issue for slow hosts (or when
// debugging messages are on). Really slow hosts may find a fast
// sender keeps them permanently in the IRQ handler. :(
// (only an issue for slow hosts) RX completion goes before
// rx_data_av as the former implies rx_busy and so the latter
// would just abort. If it reschedules another transfer
// (continuing the same frame) then it will not clear rx_busy.
// (only an issue for slow hosts) TX completion goes before RX
// data available as it is a much shorter routine - there is the
// chance that any further transfers it schedules will be complete
// by the time of the return to the head of the while loop
if (int_source & RX_BUS_MASTER_COMPLETE) {
++irq_ok;
PRINTD (DBG_IRQ|DBG_BUS|DBG_RX, "rx_bus_master_complete asserted");
rx_bus_master_complete_handler (dev);
}
if (int_source & TX_BUS_MASTER_COMPLETE) {
++irq_ok;
PRINTD (DBG_IRQ|DBG_BUS|DBG_TX, "tx_bus_master_complete asserted");
tx_bus_master_complete_handler (dev);
}
if (int_source & RX_DATA_AV) {
++irq_ok;
PRINTD (DBG_IRQ|DBG_RX, "rx_data_av asserted");
rx_data_av_handler (dev);
}
}
if (irq_ok) {
PRINTD (DBG_IRQ, "work done: %u", irq_ok);
} else {
PRINTD (DBG_IRQ|DBG_WARN, "spurious interrupt source: %#x", int_source);
}
PRINTD (DBG_IRQ|DBG_FLOW, "interrupt_handler done: %p", dev_id);
if (irq_ok)
return IRQ_HANDLED;
return IRQ_NONE;
}
/********** housekeeping **********/
static void do_housekeeping (struct timer_list *t) {
// just stats at the moment
hrz_dev * dev = from_timer(dev, t, housekeeping);
// collect device-specific (not driver/atm-linux) stats here
dev->tx_cell_count += rd_regw (dev, TX_CELL_COUNT_OFF);
dev->rx_cell_count += rd_regw (dev, RX_CELL_COUNT_OFF);
dev->hec_error_count += rd_regw (dev, HEC_ERROR_COUNT_OFF);
dev->unassigned_cell_count += rd_regw (dev, UNASSIGNED_CELL_COUNT_OFF);
mod_timer (&dev->housekeeping, jiffies + HZ/10);
return;
}
/********** find an idle channel for TX and set it up **********/
// called with tx_busy set
static short setup_idle_tx_channel (hrz_dev * dev, hrz_vcc * vcc) {
unsigned short idle_channels;
short tx_channel = -1;
unsigned int spin_count;
PRINTD (DBG_FLOW|DBG_TX, "setup_idle_tx_channel %p", dev);
// better would be to fail immediately, the caller can then decide whether
// to wait or drop (depending on whether this is UBR etc.)
spin_count = 0;
while (!(idle_channels = rd_regw (dev, TX_STATUS_OFF) & IDLE_CHANNELS_MASK)) {
PRINTD (DBG_TX|DBG_WARN, "waiting for idle TX channel");
// delay a bit here
if (++spin_count > 100) {
PRINTD (DBG_TX|DBG_ERR, "spun out waiting for idle TX channel");
return -EBUSY;
}
}
// got an idle channel
{
// tx_idle ensures we look for idle channels in RR order
int chan = dev->tx_idle;
int keep_going = 1;
while (keep_going) {
if (idle_channels & (1<<chan)) {
tx_channel = chan;
keep_going = 0;
}
++chan;
if (chan == TX_CHANS)
chan = 0;
}
dev->tx_idle = chan;
}
// set up the channel we found
{
// Initialise the cell header in the transmit channel descriptor
// a.k.a. prepare the channel and remember that we have done so.
tx_ch_desc * tx_desc = &memmap->tx_descs[tx_channel];
u32 rd_ptr;
u32 wr_ptr;
u16 channel = vcc->channel;
unsigned long flags;
spin_lock_irqsave (&dev->mem_lock, flags);
// Update the transmit channel record.
dev->tx_channel_record[tx_channel] = channel;
// xBR channel
update_tx_channel_config (dev, tx_channel, RATE_TYPE_ACCESS,
vcc->tx_xbr_bits);
// Update the PCR counter preload value etc.
update_tx_channel_config (dev, tx_channel, PCR_TIMER_ACCESS,
vcc->tx_pcr_bits);
#if 0
if (vcc->tx_xbr_bits == VBR_RATE_TYPE) {
// SCR timer
update_tx_channel_config (dev, tx_channel, SCR_TIMER_ACCESS,
vcc->tx_scr_bits);
// Bucket size...
update_tx_channel_config (dev, tx_channel, BUCKET_CAPACITY_ACCESS,
vcc->tx_bucket_bits);
// ... and fullness
update_tx_channel_config (dev, tx_channel, BUCKET_FULLNESS_ACCESS,
vcc->tx_bucket_bits);
}
#endif
// Initialise the read and write buffer pointers
rd_ptr = rd_mem (dev, &tx_desc->rd_buf_type) & BUFFER_PTR_MASK;
wr_ptr = rd_mem (dev, &tx_desc->wr_buf_type) & BUFFER_PTR_MASK;
// idle TX channels should have identical pointers
if (rd_ptr != wr_ptr) {
PRINTD (DBG_TX|DBG_ERR, "TX buffer pointers are broken!");
// spin_unlock... return -E...
// I wonder if gcc would get rid of one of the pointer aliases
}
PRINTD (DBG_TX, "TX buffer pointers are: rd %x, wr %x.",
rd_ptr, wr_ptr);
switch (vcc->aal) {
case aal0:
PRINTD (DBG_QOS|DBG_TX, "tx_channel: aal0");
rd_ptr |= CHANNEL_TYPE_RAW_CELLS;
wr_ptr |= CHANNEL_TYPE_RAW_CELLS;
break;
case aal34:
PRINTD (DBG_QOS|DBG_TX, "tx_channel: aal34");
rd_ptr |= CHANNEL_TYPE_AAL3_4;
wr_ptr |= CHANNEL_TYPE_AAL3_4;
break;
case aal5:
rd_ptr |= CHANNEL_TYPE_AAL5;
wr_ptr |= CHANNEL_TYPE_AAL5;
// Initialise the CRC
wr_mem (dev, &tx_desc->partial_crc, INITIAL_CRC);
break;
}
wr_mem (dev, &tx_desc->rd_buf_type, rd_ptr);
wr_mem (dev, &tx_desc->wr_buf_type, wr_ptr);
// Write the Cell Header
// Payload Type, CLP and GFC would go here if non-zero
wr_mem (dev, &tx_desc->cell_header, channel);
spin_unlock_irqrestore (&dev->mem_lock, flags);
}
return tx_channel;
}
/********** send a frame **********/
static int hrz_send (struct atm_vcc * atm_vcc, struct sk_buff * skb) {
unsigned int spin_count;
int free_buffers;
hrz_dev * dev = HRZ_DEV(atm_vcc->dev);
hrz_vcc * vcc = HRZ_VCC(atm_vcc);
u16 channel = vcc->channel;
u32 buffers_required;
/* signed for error return */
short tx_channel;
PRINTD (DBG_FLOW|DBG_TX, "hrz_send vc %x data %p len %u",
channel, skb->data, skb->len);
dump_skb (">>>", channel, skb);
if (atm_vcc->qos.txtp.traffic_class == ATM_NONE) {
PRINTK (KERN_ERR, "attempt to send on RX-only VC %x", channel);
hrz_kfree_skb (skb);
return -EIO;
}
// don't understand this
ATM_SKB(skb)->vcc = atm_vcc;
if (skb->len > atm_vcc->qos.txtp.max_sdu) {
PRINTK (KERN_ERR, "sk_buff length greater than agreed max_sdu, dropping...");
hrz_kfree_skb (skb);
return -EIO;
}
if (!channel) {
PRINTD (DBG_ERR|DBG_TX, "attempt to transmit on zero (rx_)channel");
hrz_kfree_skb (skb);
return -EIO;
}
#if 0
{
// where would be a better place for this? housekeeping?
u16 status;
pci_read_config_word (dev->pci_dev, PCI_STATUS, &status);
if (status & PCI_STATUS_REC_MASTER_ABORT) {
PRINTD (DBG_BUS|DBG_ERR, "Clearing PCI Master Abort (and cleaning up)");
status &= ~PCI_STATUS_REC_MASTER_ABORT;
pci_write_config_word (dev->pci_dev, PCI_STATUS, status);
if (test_bit (tx_busy, &dev->flags)) {
hrz_kfree_skb (dev->tx_skb);
tx_release (dev);
}
}
}
#endif
#ifdef DEBUG_HORIZON
/* wey-hey! */
if (channel == 1023) {
unsigned int i;
unsigned short d = 0;
char * s = skb->data;
if (*s++ == 'D') {
for (i = 0; i < 4; ++i)
d = (d << 4) | hex_to_bin(*s++);
PRINTK (KERN_INFO, "debug bitmap is now %hx", debug = d);
}
}
#endif
// wait until TX is free and grab lock
if (tx_hold (dev)) {
hrz_kfree_skb (skb);
return -ERESTARTSYS;
}
// Wait for enough space to be available in transmit buffer memory.
// should be number of cells needed + 2 (according to hardware docs)
// = ((framelen+8)+47) / 48 + 2
// = (framelen+7) / 48 + 3, hmm... faster to put addition inside XXX
buffers_required = (skb->len+(ATM_AAL5_TRAILER-1)) / ATM_CELL_PAYLOAD + 3;
// replace with timer and sleep, add dev->tx_buffers_queue (max 1 entry)
spin_count = 0;
while ((free_buffers = rd_regw (dev, TX_FREE_BUFFER_COUNT_OFF)) < buffers_required) {
PRINTD (DBG_TX, "waiting for free TX buffers, got %d of %d",
free_buffers, buffers_required);
// what is the appropriate delay? implement a timeout? (depending on line speed?)
// mdelay (1);
// what happens if we kill (current_pid, SIGKILL) ?
schedule();
if (++spin_count > 1000) {
PRINTD (DBG_TX|DBG_ERR, "spun out waiting for tx buffers, got %d of %d",
free_buffers, buffers_required);
tx_release (dev);
hrz_kfree_skb (skb);
return -ERESTARTSYS;
}
}
// Select a channel to transmit the frame on.
if (channel == dev->last_vc) {
PRINTD (DBG_TX, "last vc hack: hit");
tx_channel = dev->tx_last;
} else {
PRINTD (DBG_TX, "last vc hack: miss");
// Are we currently transmitting this VC on one of the channels?
for (tx_channel = 0; tx_channel < TX_CHANS; ++tx_channel)
if (dev->tx_channel_record[tx_channel] == channel) {
PRINTD (DBG_TX, "vc already on channel: hit");
break;
}
if (tx_channel == TX_CHANS) {
PRINTD (DBG_TX, "vc already on channel: miss");
// Find and set up an idle channel.
tx_channel = setup_idle_tx_channel (dev, vcc);
if (tx_channel < 0) {
PRINTD (DBG_TX|DBG_ERR, "failed to get channel");
tx_release (dev);
return tx_channel;
}
}
PRINTD (DBG_TX, "got channel");
SELECT_TX_CHANNEL(dev, tx_channel);
dev->last_vc = channel;
dev->tx_last = tx_channel;
}
PRINTD (DBG_TX, "using channel %u", tx_channel);
YELLOW_LED_OFF(dev);
// TX start transfer
{
unsigned int tx_len = skb->len;
unsigned int tx_iovcnt = skb_shinfo(skb)->nr_frags;
// remember this so we can free it later
dev->tx_skb = skb;
if (tx_iovcnt) {
// scatter gather transfer
dev->tx_regions = tx_iovcnt;
dev->tx_iovec = NULL; /* @@@ needs rewritten */
dev->tx_bytes = 0;
PRINTD (DBG_TX|DBG_BUS, "TX start scatter-gather transfer (iovec %p, len %d)",
skb->data, tx_len);
tx_release (dev);
hrz_kfree_skb (skb);
return -EIO;
} else {
// simple transfer
dev->tx_regions = 0;
dev->tx_iovec = NULL;
dev->tx_bytes = tx_len;
dev->tx_addr = skb->data;
PRINTD (DBG_TX|DBG_BUS, "TX start simple transfer (addr %p, len %d)",
skb->data, tx_len);
}
// and do the business
tx_schedule (dev, 0);
}
return 0;
}
/********** reset a card **********/
static void hrz_reset (const hrz_dev * dev) {
u32 control_0_reg = rd_regl (dev, CONTROL_0_REG);
// why not set RESET_HORIZON to one and wait for the card to
// reassert that bit as zero? Like so:
control_0_reg = control_0_reg & RESET_HORIZON;
wr_regl (dev, CONTROL_0_REG, control_0_reg);
while (control_0_reg & RESET_HORIZON)
control_0_reg = rd_regl (dev, CONTROL_0_REG);
// old reset code retained:
wr_regl (dev, CONTROL_0_REG, control_0_reg |
RESET_ATM | RESET_RX | RESET_TX | RESET_HOST);
// just guessing here
udelay (1000);
wr_regl (dev, CONTROL_0_REG, control_0_reg);
}
/********** read the burnt in address **********/
static void WRITE_IT_WAIT (const hrz_dev *dev, u32 ctrl)
{
wr_regl (dev, CONTROL_0_REG, ctrl);
udelay (5);
}
static void CLOCK_IT (const hrz_dev *dev, u32 ctrl)
{
// DI must be valid around rising SK edge
WRITE_IT_WAIT(dev, ctrl & ~SEEPROM_SK);
WRITE_IT_WAIT(dev, ctrl | SEEPROM_SK);
}
static u16 read_bia(const hrz_dev *dev, u16 addr)
{
u32 ctrl = rd_regl (dev, CONTROL_0_REG);
const unsigned int addr_bits = 6;
const unsigned int data_bits = 16;
unsigned int i;
u16 res;
ctrl &= ~(SEEPROM_CS | SEEPROM_SK | SEEPROM_DI);
WRITE_IT_WAIT(dev, ctrl);
// wake Serial EEPROM and send 110 (READ) command
ctrl |= (SEEPROM_CS | SEEPROM_DI);
CLOCK_IT(dev, ctrl);
ctrl |= SEEPROM_DI;
CLOCK_IT(dev, ctrl);
ctrl &= ~SEEPROM_DI;
CLOCK_IT(dev, ctrl);
for (i=0; i<addr_bits; i++) {
if (addr & (1 << (addr_bits-1)))
ctrl |= SEEPROM_DI;
else
ctrl &= ~SEEPROM_DI;
CLOCK_IT(dev, ctrl);
addr = addr << 1;
}
// we could check that we have DO = 0 here
ctrl &= ~SEEPROM_DI;
res = 0;
for (i=0;i<data_bits;i++) {
res = res >> 1;
CLOCK_IT(dev, ctrl);
if (rd_regl (dev, CONTROL_0_REG) & SEEPROM_DO)
res |= (1 << (data_bits-1));
}
ctrl &= ~(SEEPROM_SK | SEEPROM_CS);
WRITE_IT_WAIT(dev, ctrl);
return res;
}
/********** initialise a card **********/
static int hrz_init(hrz_dev *dev)
{
int onefivefive;
u16 chan;
int buff_count;
HDW * mem;
cell_buf * tx_desc;
cell_buf * rx_desc;
u32 ctrl;
ctrl = rd_regl (dev, CONTROL_0_REG);
PRINTD (DBG_INFO, "ctrl0reg is %#x", ctrl);
onefivefive = ctrl & ATM_LAYER_STATUS;
if (onefivefive)
printk (DEV_LABEL ": Horizon Ultra (at 155.52 MBps)");
else
printk (DEV_LABEL ": Horizon (at 25 MBps)");
printk (":");
// Reset the card to get everything in a known state
printk (" reset");
hrz_reset (dev);
// Clear all the buffer memory
printk (" clearing memory");
for (mem = (HDW *) memmap; mem < (HDW *) (memmap + 1); ++mem)
wr_mem (dev, mem, 0);
printk (" tx channels");
// All transmit eight channels are set up as AAL5 ABR channels with
// a 16us cell spacing. Why?
// Channel 0 gets the free buffer at 100h, channel 1 gets the free
// buffer at 110h etc.
for (chan = 0; chan < TX_CHANS; ++chan) {
tx_ch_desc * tx_desc = &memmap->tx_descs[chan];
cell_buf * buf = &memmap->inittxbufs[chan];
// initialise the read and write buffer pointers
wr_mem (dev, &tx_desc->rd_buf_type, BUF_PTR(buf));
wr_mem (dev, &tx_desc->wr_buf_type, BUF_PTR(buf));
// set the status of the initial buffers to empty
wr_mem (dev, &buf->next, BUFF_STATUS_EMPTY);
}
// Use space bufn3 at the moment for tx buffers
printk (" tx buffers");
tx_desc = memmap->bufn3;
wr_mem (dev, &memmap->txfreebufstart.next, BUF_PTR(tx_desc) | BUFF_STATUS_EMPTY);
for (buff_count = 0; buff_count < BUFN3_SIZE-1; buff_count++) {
wr_mem (dev, &tx_desc->next, BUF_PTR(tx_desc+1) | BUFF_STATUS_EMPTY);
tx_desc++;
}
wr_mem (dev, &tx_desc->next, BUF_PTR(&memmap->txfreebufend) | BUFF_STATUS_EMPTY);
// Initialise the transmit free buffer count
wr_regw (dev, TX_FREE_BUFFER_COUNT_OFF, BUFN3_SIZE);
printk (" rx channels");
// Initialise all of the receive channels to be AAL5 disabled with
// an interrupt threshold of 0
for (chan = 0; chan < RX_CHANS; ++chan) {
rx_ch_desc * rx_desc = &memmap->rx_descs[chan];
wr_mem (dev, &rx_desc->wr_buf_type, CHANNEL_TYPE_AAL5 | RX_CHANNEL_DISABLED);
}
printk (" rx buffers");
// Use space bufn4 at the moment for rx buffers
rx_desc = memmap->bufn4;
wr_mem (dev, &memmap->rxfreebufstart.next, BUF_PTR(rx_desc) | BUFF_STATUS_EMPTY);
for (buff_count = 0; buff_count < BUFN4_SIZE-1; buff_count++) {
wr_mem (dev, &rx_desc->next, BUF_PTR(rx_desc+1) | BUFF_STATUS_EMPTY);
rx_desc++;
}
wr_mem (dev, &rx_desc->next, BUF_PTR(&memmap->rxfreebufend) | BUFF_STATUS_EMPTY);
// Initialise the receive free buffer count
wr_regw (dev, RX_FREE_BUFFER_COUNT_OFF, BUFN4_SIZE);
// Initialize Horizons registers
// TX config
wr_regw (dev, TX_CONFIG_OFF,
ABR_ROUND_ROBIN | TX_NORMAL_OPERATION | DRVR_DRVRBAR_ENABLE);
// RX config. Use 10-x VC bits, x VP bits, non user cells in channel 0.
wr_regw (dev, RX_CONFIG_OFF,
DISCARD_UNUSED_VPI_VCI_BITS_SET | NON_USER_CELLS_IN_ONE_CHANNEL | vpi_bits);
// RX line config
wr_regw (dev, RX_LINE_CONFIG_OFF,
LOCK_DETECT_ENABLE | FREQUENCY_DETECT_ENABLE | GXTALOUT_SELECT_DIV4);
// Set the max AAL5 cell count to be just enough to contain the
// largest AAL5 frame that the user wants to receive
wr_regw (dev, MAX_AAL5_CELL_COUNT_OFF,
DIV_ROUND_UP(max_rx_size + ATM_AAL5_TRAILER, ATM_CELL_PAYLOAD));
// Enable receive
wr_regw (dev, RX_CONFIG_OFF, rd_regw (dev, RX_CONFIG_OFF) | RX_ENABLE);
printk (" control");
// Drive the OE of the LEDs then turn the green LED on
ctrl |= GREEN_LED_OE | YELLOW_LED_OE | GREEN_LED | YELLOW_LED;
wr_regl (dev, CONTROL_0_REG, ctrl);
// Test for a 155-capable card
if (onefivefive) {
// Select 155 mode... make this a choice (or: how do we detect
// external line speed and switch?)
ctrl |= ATM_LAYER_SELECT;
wr_regl (dev, CONTROL_0_REG, ctrl);
// test SUNI-lite vs SAMBA
// Register 0x00 in the SUNI will have some of bits 3-7 set, and
// they will always be zero for the SAMBA. Ha! Bloody hardware
// engineers. It'll never work.
if (rd_framer (dev, 0) & 0x00f0) {
// SUNI
printk (" SUNI");
// Reset, just in case
wr_framer (dev, 0x00, 0x0080);
wr_framer (dev, 0x00, 0x0000);
// Configure transmit FIFO
wr_framer (dev, 0x63, rd_framer (dev, 0x63) | 0x0002);
// Set line timed mode
wr_framer (dev, 0x05, rd_framer (dev, 0x05) | 0x0001);
} else {
// SAMBA
printk (" SAMBA");
// Reset, just in case
wr_framer (dev, 0, rd_framer (dev, 0) | 0x0001);
wr_framer (dev, 0, rd_framer (dev, 0) &~ 0x0001);
// Turn off diagnostic loopback and enable line-timed mode
wr_framer (dev, 0, 0x0002);
// Turn on transmit outputs
wr_framer (dev, 2, 0x0B80);
}
} else {
// Select 25 mode
ctrl &= ~ATM_LAYER_SELECT;
// Madge B154 setup
// none required?
}
printk (" LEDs");
GREEN_LED_ON(dev);
YELLOW_LED_ON(dev);
printk (" ESI=");
{
u16 b = 0;
int i;
u8 * esi = dev->atm_dev->esi;
// in the card I have, EEPROM
// addresses 0, 1, 2 contain 0
// addresess 5, 6 etc. contain ffff
// NB: Madge prefix is 00 00 f6 (which is 00 00 6f in Ethernet bit order)
// the read_bia routine gets the BIA in Ethernet bit order
for (i=0; i < ESI_LEN; ++i) {
if (i % 2 == 0)
b = read_bia (dev, i/2 + 2);
else
b = b >> 8;
esi[i] = b & 0xFF;
printk ("%02x", esi[i]);
}
}
// Enable RX_Q and ?X_COMPLETE interrupts only
wr_regl (dev, INT_ENABLE_REG_OFF, INTERESTING_INTERRUPTS);
printk (" IRQ on");
printk (".\n");
return onefivefive;
}
/********** check max_sdu **********/
static int check_max_sdu (hrz_aal aal, struct atm_trafprm * tp, unsigned int max_frame_size) {
PRINTD (DBG_FLOW|DBG_QOS, "check_max_sdu");
switch (aal) {
case aal0:
if (!(tp->max_sdu)) {
PRINTD (DBG_QOS, "defaulting max_sdu");
tp->max_sdu = ATM_AAL0_SDU;
} else if (tp->max_sdu != ATM_AAL0_SDU) {
PRINTD (DBG_QOS|DBG_ERR, "rejecting max_sdu");
return -EINVAL;
}
break;
case aal34:
if (tp->max_sdu == 0 || tp->max_sdu > ATM_MAX_AAL34_PDU) {
PRINTD (DBG_QOS, "%sing max_sdu", tp->max_sdu ? "capp" : "default");
tp->max_sdu = ATM_MAX_AAL34_PDU;
}
break;
case aal5:
if (tp->max_sdu == 0 || tp->max_sdu > max_frame_size) {
PRINTD (DBG_QOS, "%sing max_sdu", tp->max_sdu ? "capp" : "default");
tp->max_sdu = max_frame_size;
}
break;
}
return 0;
}
/********** check pcr **********/
// something like this should be part of ATM Linux
static int atm_pcr_check (struct atm_trafprm * tp, unsigned int pcr) {
// we are assuming non-UBR, and non-special values of pcr
if (tp->min_pcr == ATM_MAX_PCR)
PRINTD (DBG_QOS, "luser gave min_pcr = ATM_MAX_PCR");
else if (tp->min_pcr < 0)
PRINTD (DBG_QOS, "luser gave negative min_pcr");
else if (tp->min_pcr && tp->min_pcr > pcr)
PRINTD (DBG_QOS, "pcr less than min_pcr");
else
// !! max_pcr = UNSPEC (0) is equivalent to max_pcr = MAX (-1)
// easier to #define ATM_MAX_PCR 0 and have all rates unsigned?
// [this would get rid of next two conditionals]
if ((0) && tp->max_pcr == ATM_MAX_PCR)
PRINTD (DBG_QOS, "luser gave max_pcr = ATM_MAX_PCR");
else if ((tp->max_pcr != ATM_MAX_PCR) && tp->max_pcr < 0)
PRINTD (DBG_QOS, "luser gave negative max_pcr");
else if (tp->max_pcr && tp->max_pcr != ATM_MAX_PCR && tp->max_pcr < pcr)
PRINTD (DBG_QOS, "pcr greater than max_pcr");
else {
// each limit unspecified or not violated
PRINTD (DBG_QOS, "xBR(pcr) OK");
return 0;
}
PRINTD (DBG_QOS, "pcr=%u, tp: min_pcr=%d, pcr=%d, max_pcr=%d",
pcr, tp->min_pcr, tp->pcr, tp->max_pcr);
return -EINVAL;
}
/********** open VC **********/
static int hrz_open (struct atm_vcc *atm_vcc)
{
int error;
u16 channel;
struct atm_qos * qos;
struct atm_trafprm * txtp;
struct atm_trafprm * rxtp;
hrz_dev * dev = HRZ_DEV(atm_vcc->dev);
hrz_vcc vcc;
hrz_vcc * vccp; // allocated late
short vpi = atm_vcc->vpi;
int vci = atm_vcc->vci;
PRINTD (DBG_FLOW|DBG_VCC, "hrz_open %x %x", vpi, vci);
#ifdef ATM_VPI_UNSPEC
// UNSPEC is deprecated, remove this code eventually
if (vpi == ATM_VPI_UNSPEC || vci == ATM_VCI_UNSPEC) {
PRINTK (KERN_WARNING, "rejecting open with unspecified VPI/VCI (deprecated)");
return -EINVAL;
}
#endif
error = vpivci_to_channel (&channel, vpi, vci);
if (error) {
PRINTD (DBG_WARN|DBG_VCC, "VPI/VCI out of range: %hd/%d", vpi, vci);
return error;
}
vcc.channel = channel;
// max speed for the moment
vcc.tx_rate = 0x0;
qos = &atm_vcc->qos;
// check AAL and remember it
switch (qos->aal) {
case ATM_AAL0:
// we would if it were 48 bytes and not 52!
PRINTD (DBG_QOS|DBG_VCC, "AAL0");
vcc.aal = aal0;
break;
case ATM_AAL34:
// we would if I knew how do the SAR!
PRINTD (DBG_QOS|DBG_VCC, "AAL3/4");
vcc.aal = aal34;
break;
case ATM_AAL5:
PRINTD (DBG_QOS|DBG_VCC, "AAL5");
vcc.aal = aal5;
break;
default:
PRINTD (DBG_QOS|DBG_VCC, "Bad AAL!");
return -EINVAL;
}
// TX traffic parameters
// there are two, interrelated problems here: 1. the reservation of
// PCR is not a binary choice, we are given bounds and/or a
// desirable value; 2. the device is only capable of certain values,
// most of which are not integers. It is almost certainly acceptable
// to be off by a maximum of 1 to 10 cps.
// Pragmatic choice: always store an integral PCR as that which has
// been allocated, even if we allocate a little (or a lot) less,
// after rounding. The actual allocation depends on what we can
// manage with our rate selection algorithm. The rate selection
// algorithm is given an integral PCR and a tolerance and told
// whether it should round the value up or down if the tolerance is
// exceeded; it returns: a) the actual rate selected (rounded up to
// the nearest integer), b) a bit pattern to feed to the timer
// register, and c) a failure value if no applicable rate exists.
// Part of the job is done by atm_pcr_goal which gives us a PCR
// specification which says: EITHER grab the maximum available PCR
// (and perhaps a lower bound which we must not pass), OR grab this
// amount, rounding down if you have to (and perhaps a lower bound
// which we must not pass) OR grab this amount, rounding up if you
// have to (and perhaps an upper bound which we must not pass). If any
// bounds ARE passed we fail. Note that rounding is only rounding to
// match device limitations, we do not round down to satisfy
// bandwidth availability even if this would not violate any given
// lower bound.
// Note: telephony = 64kb/s = 48 byte cell payload @ 500/3 cells/s
// (say) so this is not even a binary fixpoint cell rate (but this
// device can do it). To avoid this sort of hassle we use a
// tolerance parameter (currently fixed at 10 cps).
PRINTD (DBG_QOS, "TX:");
txtp = &qos->txtp;
// set up defaults for no traffic
vcc.tx_rate = 0;
// who knows what would actually happen if you try and send on this?
vcc.tx_xbr_bits = IDLE_RATE_TYPE;
vcc.tx_pcr_bits = CLOCK_DISABLE;
#if 0
vcc.tx_scr_bits = CLOCK_DISABLE;
vcc.tx_bucket_bits = 0;
#endif
if (txtp->traffic_class != ATM_NONE) {
error = check_max_sdu (vcc.aal, txtp, max_tx_size);
if (error) {
PRINTD (DBG_QOS, "TX max_sdu check failed");
return error;
}
switch (txtp->traffic_class) {
case ATM_UBR: {
// we take "the PCR" as a rate-cap
// not reserved
vcc.tx_rate = 0;
make_rate (dev, 1<<30, round_nearest, &vcc.tx_pcr_bits, NULL);
vcc.tx_xbr_bits = ABR_RATE_TYPE;
break;
}
#if 0
case ATM_ABR: {
// reserve min, allow up to max
vcc.tx_rate = 0; // ?
make_rate (dev, 1<<30, round_nearest, &vcc.tx_pcr_bits, 0);
vcc.tx_xbr_bits = ABR_RATE_TYPE;
break;
}
#endif
case ATM_CBR: {
int pcr = atm_pcr_goal (txtp);
rounding r;
if (!pcr) {
// down vs. up, remaining bandwidth vs. unlimited bandwidth!!
// should really have: once someone gets unlimited bandwidth
// that no more non-UBR channels can be opened until the
// unlimited one closes?? For the moment, round_down means
// greedy people actually get something and not nothing
r = round_down;
// slight race (no locking) here so we may get -EAGAIN
// later; the greedy bastards would deserve it :)
PRINTD (DBG_QOS, "snatching all remaining TX bandwidth");
pcr = dev->tx_avail;
} else if (pcr < 0) {
r = round_down;
pcr = -pcr;
} else {
r = round_up;
}
error = make_rate_with_tolerance (dev, pcr, r, 10,
&vcc.tx_pcr_bits, &vcc.tx_rate);
if (error) {
PRINTD (DBG_QOS, "could not make rate from TX PCR");
return error;
}
// not really clear what further checking is needed
error = atm_pcr_check (txtp, vcc.tx_rate);
if (error) {
PRINTD (DBG_QOS, "TX PCR failed consistency check");
return error;
}
vcc.tx_xbr_bits = CBR_RATE_TYPE;
break;
}
#if 0
case ATM_VBR: {
int pcr = atm_pcr_goal (txtp);
// int scr = atm_scr_goal (txtp);
int scr = pcr/2; // just for fun
unsigned int mbs = 60; // just for fun
rounding pr;
rounding sr;
unsigned int bucket;
if (!pcr) {
pr = round_nearest;
pcr = 1<<30;
} else if (pcr < 0) {
pr = round_down;
pcr = -pcr;
} else {
pr = round_up;
}
error = make_rate_with_tolerance (dev, pcr, pr, 10,
&vcc.tx_pcr_bits, 0);
if (!scr) {
// see comments for PCR with CBR above
sr = round_down;
// slight race (no locking) here so we may get -EAGAIN
// later; the greedy bastards would deserve it :)
PRINTD (DBG_QOS, "snatching all remaining TX bandwidth");
scr = dev->tx_avail;
} else if (scr < 0) {
sr = round_down;
scr = -scr;
} else {
sr = round_up;
}
error = make_rate_with_tolerance (dev, scr, sr, 10,
&vcc.tx_scr_bits, &vcc.tx_rate);
if (error) {
PRINTD (DBG_QOS, "could not make rate from TX SCR");
return error;
}
// not really clear what further checking is needed
// error = atm_scr_check (txtp, vcc.tx_rate);
if (error) {
PRINTD (DBG_QOS, "TX SCR failed consistency check");
return error;
}
// bucket calculations (from a piece of paper...) cell bucket
// capacity must be largest integer smaller than m(p-s)/p + 1
// where m = max burst size, p = pcr, s = scr
bucket = mbs*(pcr-scr)/pcr;
if (bucket*pcr != mbs*(pcr-scr))
bucket += 1;
if (bucket > BUCKET_MAX_SIZE) {
PRINTD (DBG_QOS, "shrinking bucket from %u to %u",
bucket, BUCKET_MAX_SIZE);
bucket = BUCKET_MAX_SIZE;
}
vcc.tx_xbr_bits = VBR_RATE_TYPE;
vcc.tx_bucket_bits = bucket;
break;
}
#endif
default: {
PRINTD (DBG_QOS, "unsupported TX traffic class");
return -EINVAL;
}
}
}
// RX traffic parameters
PRINTD (DBG_QOS, "RX:");
rxtp = &qos->rxtp;
// set up defaults for no traffic
vcc.rx_rate = 0;
if (rxtp->traffic_class != ATM_NONE) {
error = check_max_sdu (vcc.aal, rxtp, max_rx_size);
if (error) {
PRINTD (DBG_QOS, "RX max_sdu check failed");
return error;
}
switch (rxtp->traffic_class) {
case ATM_UBR: {
// not reserved
break;
}
#if 0
case ATM_ABR: {
// reserve min
vcc.rx_rate = 0; // ?
break;
}
#endif
case ATM_CBR: {
int pcr = atm_pcr_goal (rxtp);
if (!pcr) {
// slight race (no locking) here so we may get -EAGAIN
// later; the greedy bastards would deserve it :)
PRINTD (DBG_QOS, "snatching all remaining RX bandwidth");
pcr = dev->rx_avail;
} else if (pcr < 0) {
pcr = -pcr;
}
vcc.rx_rate = pcr;
// not really clear what further checking is needed
error = atm_pcr_check (rxtp, vcc.rx_rate);
if (error) {
PRINTD (DBG_QOS, "RX PCR failed consistency check");
return error;
}
break;
}
#if 0
case ATM_VBR: {
// int scr = atm_scr_goal (rxtp);
int scr = 1<<16; // just for fun
if (!scr) {
// slight race (no locking) here so we may get -EAGAIN
// later; the greedy bastards would deserve it :)
PRINTD (DBG_QOS, "snatching all remaining RX bandwidth");
scr = dev->rx_avail;
} else if (scr < 0) {
scr = -scr;
}
vcc.rx_rate = scr;
// not really clear what further checking is needed
// error = atm_scr_check (rxtp, vcc.rx_rate);
if (error) {
PRINTD (DBG_QOS, "RX SCR failed consistency check");
return error;
}
break;
}
#endif
default: {
PRINTD (DBG_QOS, "unsupported RX traffic class");
return -EINVAL;
}
}
}
// late abort useful for diagnostics
if (vcc.aal != aal5) {
PRINTD (DBG_QOS, "AAL not supported");
return -EINVAL;
}
// get space for our vcc stuff and copy parameters into it
vccp = kmalloc (sizeof(hrz_vcc), GFP_KERNEL);
if (!vccp) {
PRINTK (KERN_ERR, "out of memory!");
return -ENOMEM;
}
*vccp = vcc;
// clear error and grab cell rate resource lock
error = 0;
spin_lock (&dev->rate_lock);
if (vcc.tx_rate > dev->tx_avail) {
PRINTD (DBG_QOS, "not enough TX PCR left");
error = -EAGAIN;
}
if (vcc.rx_rate > dev->rx_avail) {
PRINTD (DBG_QOS, "not enough RX PCR left");
error = -EAGAIN;
}
if (!error) {
// really consume cell rates
dev->tx_avail -= vcc.tx_rate;
dev->rx_avail -= vcc.rx_rate;
PRINTD (DBG_QOS|DBG_VCC, "reserving %u TX PCR and %u RX PCR",
vcc.tx_rate, vcc.rx_rate);
}
// release lock and exit on error
spin_unlock (&dev->rate_lock);
if (error) {
PRINTD (DBG_QOS|DBG_VCC, "insufficient cell rate resources");
kfree (vccp);
return error;
}
// this is "immediately before allocating the connection identifier
// in hardware" - so long as the next call does not fail :)
set_bit(ATM_VF_ADDR,&atm_vcc->flags);
// any errors here are very serious and should never occur
if (rxtp->traffic_class != ATM_NONE) {
if (dev->rxer[channel]) {
PRINTD (DBG_ERR|DBG_VCC, "VC already open for RX");
error = -EBUSY;
}
if (!error)
error = hrz_open_rx (dev, channel);
if (error) {
kfree (vccp);
return error;
}
// this link allows RX frames through
dev->rxer[channel] = atm_vcc;
}
// success, set elements of atm_vcc
atm_vcc->dev_data = (void *) vccp;
// indicate readiness
set_bit(ATM_VF_READY,&atm_vcc->flags);
return 0;
}
/********** close VC **********/
static void hrz_close (struct atm_vcc * atm_vcc) {
hrz_dev * dev = HRZ_DEV(atm_vcc->dev);
hrz_vcc * vcc = HRZ_VCC(atm_vcc);
u16 channel = vcc->channel;
PRINTD (DBG_VCC|DBG_FLOW, "hrz_close");
// indicate unreadiness
clear_bit(ATM_VF_READY,&atm_vcc->flags);
if (atm_vcc->qos.txtp.traffic_class != ATM_NONE) {
unsigned int i;
// let any TX on this channel that has started complete
// no restart, just keep trying
while (tx_hold (dev))
;
// remove record of any tx_channel having been setup for this channel
for (i = 0; i < TX_CHANS; ++i)
if (dev->tx_channel_record[i] == channel) {
dev->tx_channel_record[i] = -1;
break;
}
if (dev->last_vc == channel)
dev->tx_last = -1;
tx_release (dev);
}
if (atm_vcc->qos.rxtp.traffic_class != ATM_NONE) {
// disable RXing - it tries quite hard
hrz_close_rx (dev, channel);
// forget the vcc - no more skbs will be pushed
if (atm_vcc != dev->rxer[channel])
PRINTK (KERN_ERR, "%s atm_vcc=%p rxer[channel]=%p",
"arghhh! we're going to die!",
atm_vcc, dev->rxer[channel]);
dev->rxer[channel] = NULL;
}
// atomically release our rate reservation
spin_lock (&dev->rate_lock);
PRINTD (DBG_QOS|DBG_VCC, "releasing %u TX PCR and %u RX PCR",
vcc->tx_rate, vcc->rx_rate);
dev->tx_avail += vcc->tx_rate;
dev->rx_avail += vcc->rx_rate;
spin_unlock (&dev->rate_lock);
// free our structure
kfree (vcc);
// say the VPI/VCI is free again
clear_bit(ATM_VF_ADDR,&atm_vcc->flags);
}
#if 0
static int hrz_ioctl (struct atm_dev * atm_dev, unsigned int cmd, void *arg) {
hrz_dev * dev = HRZ_DEV(atm_dev);
PRINTD (DBG_FLOW, "hrz_ioctl");
return -1;
}
unsigned char hrz_phy_get (struct atm_dev * atm_dev, unsigned long addr) {
hrz_dev * dev = HRZ_DEV(atm_dev);
PRINTD (DBG_FLOW, "hrz_phy_get");
return 0;
}
static void hrz_phy_put (struct atm_dev * atm_dev, unsigned char value,
unsigned long addr) {
hrz_dev * dev = HRZ_DEV(atm_dev);
PRINTD (DBG_FLOW, "hrz_phy_put");
}
static int hrz_change_qos (struct atm_vcc * atm_vcc, struct atm_qos *qos, int flgs) {
hrz_dev * dev = HRZ_DEV(vcc->dev);
PRINTD (DBG_FLOW, "hrz_change_qos");
return -1;
}
#endif
/********** proc file contents **********/
static int hrz_proc_read (struct atm_dev * atm_dev, loff_t * pos, char * page) {
hrz_dev * dev = HRZ_DEV(atm_dev);
int left = *pos;
PRINTD (DBG_FLOW, "hrz_proc_read");
/* more diagnostics here? */
#if 0
if (!left--) {
unsigned int count = sprintf (page, "vbr buckets:");
unsigned int i;
for (i = 0; i < TX_CHANS; ++i)
count += sprintf (page, " %u/%u",
query_tx_channel_config (dev, i, BUCKET_FULLNESS_ACCESS),
query_tx_channel_config (dev, i, BUCKET_CAPACITY_ACCESS));
count += sprintf (page+count, ".\n");
return count;
}
#endif
if (!left--)
return sprintf (page,
"cells: TX %lu, RX %lu, HEC errors %lu, unassigned %lu.\n",
dev->tx_cell_count, dev->rx_cell_count,
dev->hec_error_count, dev->unassigned_cell_count);
if (!left--)
return sprintf (page,
"free cell buffers: TX %hu, RX %hu+%hu.\n",
rd_regw (dev, TX_FREE_BUFFER_COUNT_OFF),
rd_regw (dev, RX_FREE_BUFFER_COUNT_OFF),
dev->noof_spare_buffers);
if (!left--)
return sprintf (page,
"cps remaining: TX %u, RX %u\n",
dev->tx_avail, dev->rx_avail);
return 0;
}
static const struct atmdev_ops hrz_ops = {
.open = hrz_open,
.close = hrz_close,
.send = hrz_send,
.proc_read = hrz_proc_read,
.owner = THIS_MODULE,
};
static int hrz_probe(struct pci_dev *pci_dev,
const struct pci_device_id *pci_ent)
{
hrz_dev * dev;
int err = 0;
// adapter slot free, read resources from PCI configuration space
u32 iobase = pci_resource_start (pci_dev, 0);
u32 * membase = bus_to_virt (pci_resource_start (pci_dev, 1));
unsigned int irq;
unsigned char lat;
PRINTD (DBG_FLOW, "hrz_probe");
if (pci_enable_device(pci_dev))
return -EINVAL;
/* XXX DEV_LABEL is a guess */
if (!request_region(iobase, HRZ_IO_EXTENT, DEV_LABEL)) {
err = -EINVAL;
goto out_disable;
}
dev = kzalloc(sizeof(hrz_dev), GFP_KERNEL);
if (!dev) {
// perhaps we should be nice: deregister all adapters and abort?
PRINTD(DBG_ERR, "out of memory");
err = -ENOMEM;
goto out_release;
}
pci_set_drvdata(pci_dev, dev);
// grab IRQ and install handler - move this someplace more sensible
irq = pci_dev->irq;
if (request_irq(irq,
interrupt_handler,
IRQF_SHARED, /* irqflags guess */
DEV_LABEL, /* name guess */
dev)) {
PRINTD(DBG_WARN, "request IRQ failed!");
err = -EINVAL;
goto out_free;
}
PRINTD(DBG_INFO, "found Madge ATM adapter (hrz) at: IO %x, IRQ %u, MEM %p",
iobase, irq, membase);
dev->atm_dev = atm_dev_register(DEV_LABEL, &pci_dev->dev, &hrz_ops, -1,
NULL);
if (!(dev->atm_dev)) {
PRINTD(DBG_ERR, "failed to register Madge ATM adapter");
err = -EINVAL;
goto out_free_irq;
}
PRINTD(DBG_INFO, "registered Madge ATM adapter (no. %d) (%p) at %p",
dev->atm_dev->number, dev, dev->atm_dev);
dev->atm_dev->dev_data = (void *) dev;
dev->pci_dev = pci_dev;
// enable bus master accesses
pci_set_master(pci_dev);
// frobnicate latency (upwards, usually)
pci_read_config_byte(pci_dev, PCI_LATENCY_TIMER, &lat);
if (pci_lat) {
PRINTD(DBG_INFO, "%s PCI latency timer from %hu to %hu",
"changing", lat, pci_lat);
pci_write_config_byte(pci_dev, PCI_LATENCY_TIMER, pci_lat);
} else if (lat < MIN_PCI_LATENCY) {
PRINTK(KERN_INFO, "%s PCI latency timer from %hu to %hu",
"increasing", lat, MIN_PCI_LATENCY);
pci_write_config_byte(pci_dev, PCI_LATENCY_TIMER, MIN_PCI_LATENCY);
}
dev->iobase = iobase;
dev->irq = irq;
dev->membase = membase;
dev->rx_q_entry = dev->rx_q_reset = &memmap->rx_q_entries[0];
dev->rx_q_wrap = &memmap->rx_q_entries[RX_CHANS-1];
// these next three are performance hacks
dev->last_vc = -1;
dev->tx_last = -1;
dev->tx_idle = 0;
dev->tx_regions = 0;
dev->tx_bytes = 0;
dev->tx_skb = NULL;
dev->tx_iovec = NULL;
dev->tx_cell_count = 0;
dev->rx_cell_count = 0;
dev->hec_error_count = 0;
dev->unassigned_cell_count = 0;
dev->noof_spare_buffers = 0;
{
unsigned int i;
for (i = 0; i < TX_CHANS; ++i)
dev->tx_channel_record[i] = -1;
}
dev->flags = 0;
// Allocate cell rates and remember ASIC version
// Fibre: ATM_OC3_PCR = 1555200000/8/270*260/53 - 29/53
// Copper: (WRONG) we want 6 into the above, close to 25Mb/s
// Copper: (plagarise!) 25600000/8/270*260/53 - n/53
if (hrz_init(dev)) {
// to be really pedantic, this should be ATM_OC3c_PCR
dev->tx_avail = ATM_OC3_PCR;
dev->rx_avail = ATM_OC3_PCR;
set_bit(ultra, &dev->flags); // NOT "|= ultra" !
} else {
dev->tx_avail = ((25600000/8)*26)/(27*53);
dev->rx_avail = ((25600000/8)*26)/(27*53);
PRINTD(DBG_WARN, "Buggy ASIC: no TX bus-mastering.");
}
// rate changes spinlock
spin_lock_init(&dev->rate_lock);
// on-board memory access spinlock; we want atomic reads and
// writes to adapter memory (handles IRQ and SMP)
spin_lock_init(&dev->mem_lock);
init_waitqueue_head(&dev->tx_queue);
// vpi in 0..4, vci in 6..10
dev->atm_dev->ci_range.vpi_bits = vpi_bits;
dev->atm_dev->ci_range.vci_bits = 10-vpi_bits;
timer_setup(&dev->housekeeping, do_housekeeping, 0);
mod_timer(&dev->housekeeping, jiffies);
out:
return err;
out_free_irq:
free_irq(irq, dev);
out_free:
kfree(dev);
out_release:
release_region(iobase, HRZ_IO_EXTENT);
out_disable:
pci_disable_device(pci_dev);
goto out;
}
static void hrz_remove_one(struct pci_dev *pci_dev)
{
hrz_dev *dev;
dev = pci_get_drvdata(pci_dev);
PRINTD(DBG_INFO, "closing %p (atm_dev = %p)", dev, dev->atm_dev);
del_timer_sync(&dev->housekeeping);
hrz_reset(dev);
atm_dev_deregister(dev->atm_dev);
free_irq(dev->irq, dev);
release_region(dev->iobase, HRZ_IO_EXTENT);
kfree(dev);
pci_disable_device(pci_dev);
}
static void __init hrz_check_args (void) {
#ifdef DEBUG_HORIZON
PRINTK (KERN_NOTICE, "debug bitmap is %hx", debug &= DBG_MASK);
#else
if (debug)
PRINTK (KERN_NOTICE, "no debug support in this image");
#endif
if (vpi_bits > HRZ_MAX_VPI)
PRINTK (KERN_ERR, "vpi_bits has been limited to %hu",
vpi_bits = HRZ_MAX_VPI);
if (max_tx_size < 0 || max_tx_size > TX_AAL5_LIMIT)
PRINTK (KERN_NOTICE, "max_tx_size has been limited to %hu",
max_tx_size = TX_AAL5_LIMIT);
if (max_rx_size < 0 || max_rx_size > RX_AAL5_LIMIT)
PRINTK (KERN_NOTICE, "max_rx_size has been limited to %hu",
max_rx_size = RX_AAL5_LIMIT);
return;
}
MODULE_AUTHOR(maintainer_string);
MODULE_DESCRIPTION(description_string);
MODULE_LICENSE("GPL");
module_param(debug, ushort, 0644);
module_param(vpi_bits, ushort, 0);
module_param(max_tx_size, int, 0);
module_param(max_rx_size, int, 0);
module_param(pci_lat, byte, 0);
MODULE_PARM_DESC(debug, "debug bitmap, see .h file");
MODULE_PARM_DESC(vpi_bits, "number of bits (0..4) to allocate to VPIs");
MODULE_PARM_DESC(max_tx_size, "maximum size of TX AAL5 frames");
MODULE_PARM_DESC(max_rx_size, "maximum size of RX AAL5 frames");
MODULE_PARM_DESC(pci_lat, "PCI latency in bus cycles");
static const struct pci_device_id hrz_pci_tbl[] = {
{ PCI_VENDOR_ID_MADGE, PCI_DEVICE_ID_MADGE_HORIZON, PCI_ANY_ID, PCI_ANY_ID,
0, 0, 0 },
{ 0, }
};
MODULE_DEVICE_TABLE(pci, hrz_pci_tbl);
static struct pci_driver hrz_driver = {
.name = "horizon",
.probe = hrz_probe,
.remove = hrz_remove_one,
.id_table = hrz_pci_tbl,
};
/********** module entry **********/
static int __init hrz_module_init (void) {
BUILD_BUG_ON(sizeof(struct MEMMAP) != 128*1024/4);
show_version();
// check arguments
hrz_check_args();
// get the juice
return pci_register_driver(&hrz_driver);
}
/********** module exit **********/
static void __exit hrz_module_exit (void) {
PRINTD (DBG_FLOW, "cleanup_module");
pci_unregister_driver(&hrz_driver);
}
module_init(hrz_module_init);
module_exit(hrz_module_exit);
drivers/atm/horizon.h deleted 100644 → 0
View file @ 41c335c8
/* SPDX-License-Identifier: GPL-2.0-or-later */
/*
Madge Horizon ATM Adapter driver.
Copyright (C) 1995-1999 Madge Networks Ltd.
*/
/*
IMPORTANT NOTE: Madge Networks no longer makes the adapters
supported by this driver and makes no commitment to maintain it.
*/
/* too many macros - change to inline functions */
#ifndef DRIVER_ATM_HORIZON_H
#define DRIVER_ATM_HORIZON_H
#ifdef CONFIG_ATM_HORIZON_DEBUG
#define DEBUG_HORIZON
#endif
#define DEV_LABEL "hrz"
#ifndef PCI_VENDOR_ID_MADGE
#define PCI_VENDOR_ID_MADGE 0x10B6
#endif
#ifndef PCI_DEVICE_ID_MADGE_HORIZON
#define PCI_DEVICE_ID_MADGE_HORIZON 0x1000
#endif
// diagnostic output
#define PRINTK(severity,format,args...) \
printk(severity DEV_LABEL ": " format "\n" , ## args)
#ifdef DEBUG_HORIZON
#define DBG_ERR 0x0001
#define DBG_WARN 0x0002
#define DBG_INFO 0x0004
#define DBG_VCC 0x0008
#define DBG_QOS 0x0010
#define DBG_TX 0x0020
#define DBG_RX 0x0040
#define DBG_SKB 0x0080
#define DBG_IRQ 0x0100
#define DBG_FLOW 0x0200
#define DBG_BUS 0x0400
#define DBG_REGS 0x0800
#define DBG_DATA 0x1000
#define DBG_MASK 0x1fff
/* the ## prevents the annoying double expansion of the macro arguments */
/* KERN_INFO is used since KERN_DEBUG often does not make it to the console */
#define PRINTDB(bits,format,args...) \
( (debug & (bits)) ? printk (KERN_INFO DEV_LABEL ": " format , ## args) : 1 )
#define PRINTDM(bits,format,args...) \
( (debug & (bits)) ? printk (format , ## args) : 1 )
#define PRINTDE(bits,format,args...) \
( (debug & (bits)) ? printk (format "\n" , ## args) : 1 )
#define PRINTD(bits,format,args...) \
( (debug & (bits)) ? printk (KERN_INFO DEV_LABEL ": " format "\n" , ## args) : 1 )
#else
#define PRINTD(bits,format,args...)
#define PRINTDB(bits,format,args...)
#define PRINTDM(bits,format,args...)
#define PRINTDE(bits,format,args...)
#endif
#define PRINTDD(sec,fmt,args...)
#define PRINTDDB(sec,fmt,args...)
#define PRINTDDM(sec,fmt,args...)
#define PRINTDDE(sec,fmt,args...)
// fixed constants
#define SPARE_BUFFER_POOL_SIZE MAX_VCS
#define HRZ_MAX_VPI 4
#define MIN_PCI_LATENCY 48 // 24 IS TOO SMALL
/* Horizon specific bits */
/* Register offsets */
#define HRZ_IO_EXTENT 0x80
#define DATA_PORT_OFF 0x00
#define TX_CHANNEL_PORT_OFF 0x04
#define TX_DESCRIPTOR_PORT_OFF 0x08
#define MEMORY_PORT_OFF 0x0C
#define MEM_WR_ADDR_REG_OFF 0x14
#define MEM_RD_ADDR_REG_OFF 0x18
#define CONTROL_0_REG 0x1C
#define INT_SOURCE_REG_OFF 0x20
#define INT_ENABLE_REG_OFF 0x24
#define MASTER_RX_ADDR_REG_OFF 0x28
#define MASTER_RX_COUNT_REG_OFF 0x2C
#define MASTER_TX_ADDR_REG_OFF 0x30
#define MASTER_TX_COUNT_REG_OFF 0x34
#define TX_DESCRIPTOR_REG_OFF 0x38
#define TX_CHANNEL_CONFIG_COMMAND_OFF 0x40
#define TX_CHANNEL_CONFIG_DATA_OFF 0x44
#define TX_FREE_BUFFER_COUNT_OFF 0x48
#define RX_FREE_BUFFER_COUNT_OFF 0x4C
#define TX_CONFIG_OFF 0x50
#define TX_STATUS_OFF 0x54
#define RX_CONFIG_OFF 0x58
#define RX_LINE_CONFIG_OFF 0x5C
#define RX_QUEUE_RD_PTR_OFF 0x60
#define RX_QUEUE_WR_PTR_OFF 0x64
#define MAX_AAL5_CELL_COUNT_OFF 0x68
#define RX_CHANNEL_PORT_OFF 0x6C
#define TX_CELL_COUNT_OFF 0x70
#define RX_CELL_COUNT_OFF 0x74
#define HEC_ERROR_COUNT_OFF 0x78
#define UNASSIGNED_CELL_COUNT_OFF 0x7C
/* Register bit definitions */
/* Control 0 register */
#define SEEPROM_DO 0x00000001
#define SEEPROM_DI 0x00000002
#define SEEPROM_SK 0x00000004
#define SEEPROM_CS 0x00000008
#define DEBUG_BIT_0 0x00000010
#define DEBUG_BIT_1 0x00000020
#define DEBUG_BIT_2 0x00000040
// RESERVED 0x00000080
#define DEBUG_BIT_0_OE 0x00000100
#define DEBUG_BIT_1_OE 0x00000200
#define DEBUG_BIT_2_OE 0x00000400
// RESERVED 0x00000800
#define DEBUG_BIT_0_STATE 0x00001000
#define DEBUG_BIT_1_STATE 0x00002000
#define DEBUG_BIT_2_STATE 0x00004000
// RESERVED 0x00008000
#define GENERAL_BIT_0 0x00010000
#define GENERAL_BIT_1 0x00020000
#define GENERAL_BIT_2 0x00040000
#define GENERAL_BIT_3 0x00080000
#define RESET_HORIZON 0x00100000
#define RESET_ATM 0x00200000
#define RESET_RX 0x00400000
#define RESET_TX 0x00800000
#define RESET_HOST 0x01000000
// RESERVED 0x02000000
#define TARGET_RETRY_DISABLE 0x04000000
#define ATM_LAYER_SELECT 0x08000000
#define ATM_LAYER_STATUS 0x10000000
// RESERVED 0xE0000000
/* Interrupt source and enable registers */
#define RX_DATA_AV 0x00000001
#define RX_DISABLED 0x00000002
#define TIMING_MARKER 0x00000004
#define FORCED 0x00000008
#define RX_BUS_MASTER_COMPLETE 0x00000010
#define TX_BUS_MASTER_COMPLETE 0x00000020
#define ABR_TX_CELL_COUNT_INT 0x00000040
#define DEBUG_INT 0x00000080
// RESERVED 0xFFFFFF00
/* PIO and Bus Mastering */
#define MAX_PIO_COUNT 0x000000ff // 255 - make tunable?
// 8188 is a hard limit for bus mastering
#define MAX_TRANSFER_COUNT 0x00001ffc // 8188
#define MASTER_TX_AUTO_APPEND_DESC 0x80000000
/* TX channel config command port */
#define PCR_TIMER_ACCESS 0x0000
#define SCR_TIMER_ACCESS 0x0001
#define BUCKET_CAPACITY_ACCESS 0x0002
#define BUCKET_FULLNESS_ACCESS 0x0003
#define RATE_TYPE_ACCESS 0x0004
// UNUSED 0x00F8
#define TX_CHANNEL_CONFIG_MULT 0x0100
// UNUSED 0xF800
#define BUCKET_MAX_SIZE 0x003f
/* TX channel config data port */
#define CLOCK_SELECT_SHIFT 4
#define CLOCK_DISABLE 0x00ff
#define IDLE_RATE_TYPE 0x0
#define ABR_RATE_TYPE 0x1
#define VBR_RATE_TYPE 0x2
#define CBR_RATE_TYPE 0x3
/* TX config register */
#define DRVR_DRVRBAR_ENABLE 0x0001
#define TXCLK_MUX_SELECT_RCLK 0x0002
#define TRANSMIT_TIMING_MARKER 0x0004
#define LOOPBACK_TIMING_MARKER 0x0008
#define TX_TEST_MODE_16MHz 0x0000
#define TX_TEST_MODE_8MHz 0x0010
#define TX_TEST_MODE_5_33MHz 0x0020
#define TX_TEST_MODE_4MHz 0x0030
#define TX_TEST_MODE_3_2MHz 0x0040
#define TX_TEST_MODE_2_66MHz 0x0050
#define TX_TEST_MODE_2_29MHz 0x0060
#define TX_NORMAL_OPERATION 0x0070
#define ABR_ROUND_ROBIN 0x0080
/* TX status register */
#define IDLE_CHANNELS_MASK 0x00FF
#define ABR_CELL_COUNT_REACHED_MULT 0x0100
#define ABR_CELL_COUNT_REACHED_MASK 0xFF
/* RX config register */
#define NON_USER_CELLS_IN_ONE_CHANNEL 0x0008
#define RX_ENABLE 0x0010
#define IGNORE_UNUSED_VPI_VCI_BITS_SET 0x0000
#define NON_USER_UNUSED_VPI_VCI_BITS_SET 0x0020
#define DISCARD_UNUSED_VPI_VCI_BITS_SET 0x0040
/* RX line config register */
#define SIGNAL_LOSS 0x0001
#define FREQUENCY_DETECT_ERROR 0x0002
#define LOCK_DETECT_ERROR 0x0004
#define SELECT_INTERNAL_LOOPBACK 0x0008
#define LOCK_DETECT_ENABLE 0x0010
#define FREQUENCY_DETECT_ENABLE 0x0020
#define USER_FRAQ 0x0040
#define GXTALOUT_SELECT_DIV4 0x0080
#define GXTALOUT_SELECT_NO_GATING 0x0100
#define TIMING_MARKER_RECEIVED 0x0200
/* RX channel port */
#define RX_CHANNEL_MASK 0x03FF
// UNUSED 0x3C00
#define FLUSH_CHANNEL 0x4000
#define RX_CHANNEL_UPDATE_IN_PROGRESS 0x8000
/* Receive queue entry */
#define RX_Q_ENTRY_LENGTH_MASK 0x0000FFFF
#define RX_Q_ENTRY_CHANNEL_SHIFT 16
#define SIMONS_DODGEY_MARKER 0x08000000
#define RX_CONGESTION_EXPERIENCED 0x10000000
#define RX_CRC_10_OK 0x20000000
#define RX_CRC_32_OK 0x40000000
#define RX_COMPLETE_FRAME 0x80000000
/* Offsets and constants for use with the buffer memory */
/* Buffer pointers and channel types */
#define BUFFER_PTR_MASK 0x0000FFFF
#define RX_INT_THRESHOLD_MULT 0x00010000
#define RX_INT_THRESHOLD_MASK 0x07FF
#define INT_EVERY_N_CELLS 0x08000000
#define CONGESTION_EXPERIENCED 0x10000000
#define FIRST_CELL_OF_AAL5_FRAME 0x20000000
#define CHANNEL_TYPE_AAL5 0x00000000
#define CHANNEL_TYPE_RAW_CELLS 0x40000000
#define CHANNEL_TYPE_AAL3_4 0x80000000
/* Buffer status stuff */
#define BUFF_STATUS_MASK 0x00030000
#define BUFF_STATUS_EMPTY 0x00000000
#define BUFF_STATUS_CELL_AV 0x00010000
#define BUFF_STATUS_LAST_CELL_AV 0x00020000
/* Transmit channel stuff */
/* Receive channel stuff */
#define RX_CHANNEL_DISABLED 0x00000000
#define RX_CHANNEL_IDLE 0x00000001
/* General things */
#define INITIAL_CRC 0xFFFFFFFF
// A Horizon u32, a byte! Really nasty. Horizon pointers are (32 bit)
// word addresses and so standard C pointer operations break (as they
// assume byte addresses); so we pretend that Horizon words (and word
// pointers) are bytes (and byte pointers) for the purposes of having
// a memory map that works.
typedef u8 HDW;
typedef struct cell_buf {
HDW payload[12];
HDW next;
HDW cell_count; // AAL5 rx bufs
HDW res;
union {
HDW partial_crc; // AAL5 rx bufs
HDW cell_header; // RAW bufs
} u;
} cell_buf;
typedef struct tx_ch_desc {
HDW rd_buf_type;
HDW wr_buf_type;
HDW partial_crc;
HDW cell_header;
} tx_ch_desc;
typedef struct rx_ch_desc {
HDW wr_buf_type;
HDW rd_buf_type;
} rx_ch_desc;
typedef struct rx_q_entry {
HDW entry;
} rx_q_entry;
#define TX_CHANS 8
#define RX_CHANS 1024
#define RX_QS 1024
#define MAX_VCS RX_CHANS
/* Horizon buffer memory map */
// TX Channel Descriptors 2
// TX Initial Buffers 8 // TX_CHANS
#define BUFN1_SIZE 118 // (126 - TX_CHANS)
// RX/TX Start/End Buffers 4
#define BUFN2_SIZE 124
// RX Queue Entries 64
#define BUFN3_SIZE 192
// RX Channel Descriptors 128
#define BUFN4_SIZE 1408
// TOTAL cell_buff chunks 2048
// cell_buf bufs[2048];
// HDW dws[32768];
typedef struct MEMMAP {
tx_ch_desc tx_descs[TX_CHANS]; // 8 * 4 = 32 , 0x0020
cell_buf inittxbufs[TX_CHANS]; // these are really
cell_buf bufn1[BUFN1_SIZE]; // part of this pool
cell_buf txfreebufstart;
cell_buf txfreebufend;
cell_buf rxfreebufstart;
cell_buf rxfreebufend; // 8+118+1+1+1+1+124 = 254
cell_buf bufn2[BUFN2_SIZE]; // 16 * 254 = 4064 , 0x1000
rx_q_entry rx_q_entries[RX_QS]; // 1 * 1024 = 1024 , 0x1400
cell_buf bufn3[BUFN3_SIZE]; // 16 * 192 = 3072 , 0x2000
rx_ch_desc rx_descs[MAX_VCS]; // 2 * 1024 = 2048 , 0x2800
cell_buf bufn4[BUFN4_SIZE]; // 16 * 1408 = 22528 , 0x8000
} MEMMAP;
#define memmap ((MEMMAP *)0)
/* end horizon specific bits */
typedef enum {
aal0,
aal34,
aal5
} hrz_aal;
typedef enum {
tx_busy,
rx_busy,
ultra
} hrz_flags;
// a single struct pointed to by atm_vcc->dev_data
typedef struct {
unsigned int tx_rate;
unsigned int rx_rate;
u16 channel;
u16 tx_xbr_bits;
u16 tx_pcr_bits;
#if 0
u16 tx_scr_bits;
u16 tx_bucket_bits;
#endif
hrz_aal aal;
} hrz_vcc;
struct hrz_dev {
u32 iobase;
u32 * membase;
struct sk_buff * rx_skb; // skb being RXed
unsigned int rx_bytes; // bytes remaining to RX within region
void * rx_addr; // addr to send bytes to (for PIO)
unsigned int rx_channel; // channel that the skb is going out on
struct sk_buff * tx_skb; // skb being TXed
unsigned int tx_bytes; // bytes remaining to TX within region
void * tx_addr; // addr to send bytes from (for PIO)
struct iovec * tx_iovec; // remaining regions
unsigned int tx_regions; // number of remaining regions
spinlock_t mem_lock;
wait_queue_head_t tx_queue;
u8 irq;
unsigned long flags;
u8 tx_last;
u8 tx_idle;
rx_q_entry * rx_q_reset;
rx_q_entry * rx_q_entry;
rx_q_entry * rx_q_wrap;
struct atm_dev * atm_dev;
u32 last_vc;
int noof_spare_buffers;
u16 spare_buffers[SPARE_BUFFER_POOL_SIZE];
u16 tx_channel_record[TX_CHANS];
// this is what we follow when we get incoming data
u32 txer[MAX_VCS/32];
struct atm_vcc * rxer[MAX_VCS];
// cell rate allocation
spinlock_t rate_lock;
unsigned int rx_avail;
unsigned int tx_avail;
// dev stats
unsigned long tx_cell_count;
unsigned long rx_cell_count;
unsigned long hec_error_count;
unsigned long unassigned_cell_count;
struct pci_dev * pci_dev;
struct timer_list housekeeping;
};
typedef struct hrz_dev hrz_dev;
/* macros for use later */
#define BUF_PTR(cbptr) ((cbptr) - (cell_buf *) 0)
#define INTERESTING_INTERRUPTS \
(RX_DATA_AV | RX_DISABLED | TX_BUS_MASTER_COMPLETE | RX_BUS_MASTER_COMPLETE)
// 190 cells by default (192 TX buffers - 2 elbow room, see docs)
#define TX_AAL5_LIMIT (190*ATM_CELL_PAYLOAD-ATM_AAL5_TRAILER) // 9112
// Have enough RX buffers (unless we allow other buffer splits)
#define RX_AAL5_LIMIT ATM_MAX_AAL5_PDU
/* multi-statement macro protector */
#define DW(x) do{ x } while(0)
#define HRZ_DEV(atm_dev) ((hrz_dev *) (atm_dev)->dev_data)
#define HRZ_VCC(atm_vcc) ((hrz_vcc *) (atm_vcc)->dev_data)
/* Turn the LEDs on and off */
// The LEDs bits are upside down in that setting the bit in the debug
// register will turn the appropriate LED off.
#define YELLOW_LED DEBUG_BIT_0
#define GREEN_LED DEBUG_BIT_1
#define YELLOW_LED_OE DEBUG_BIT_0_OE
#define GREEN_LED_OE DEBUG_BIT_1_OE
#define GREEN_LED_OFF(dev) \
wr_regl (dev, CONTROL_0_REG, rd_regl (dev, CONTROL_0_REG) | GREEN_LED)
#define GREEN_LED_ON(dev) \
wr_regl (dev, CONTROL_0_REG, rd_regl (dev, CONTROL_0_REG) &~ GREEN_LED)
#define YELLOW_LED_OFF(dev) \
wr_regl (dev, CONTROL_0_REG, rd_regl (dev, CONTROL_0_REG) | YELLOW_LED)
#define YELLOW_LED_ON(dev) \
wr_regl (dev, CONTROL_0_REG, rd_regl (dev, CONTROL_0_REG) &~ YELLOW_LED)
typedef enum {
round_up,
round_down,
round_nearest
} rounding;
#endif /* DRIVER_ATM_HORIZON_H */
Markdown is supported
0% or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7