Commit 5d4294b8 authored by Sylwester Nawrocki's avatar Sylwester Nawrocki Committed by Mauro Carvalho Chehab

[media] m5mols: Don't ignore v4l2_ctrl_handler_setup() return value

v4l2_ctrl_handler_setup() may fail so check its return value when
restoring controls after device is powered on. While at it simplify
the m5mols_restore_function() a bit.
Acked-by: default avatarHeungJun Kim <riverful.kim@samsung.com>
Signed-off-by: default avatarSylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: default avatarKyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: default avatarMauro Carvalho Chehab <mchehab@redhat.com>
parent d5048c9a
......@@ -188,15 +188,16 @@ struct m5mols_info {
struct media_pad pad;
struct v4l2_mbus_framefmt ffmt[M5MOLS_RESTYPE_MAX];
int res_type;
wait_queue_head_t irq_waitq;
atomic_t irq_done;
struct v4l2_ctrl_handler handle;
/* Autoexposure/exposure control cluster */
struct {
struct v4l2_ctrl *autoexposure;
struct v4l2_ctrl *exposure;
};
struct v4l2_ctrl *autowb;
struct v4l2_ctrl *colorfx;
struct v4l2_ctrl *saturation;
......@@ -213,10 +214,10 @@ struct m5mols_info {
bool lock_awb;
u8 resolution;
u8 mode;
int (*set_power)(struct device *dev, int on);
};
#define is_ctrl_synced(__info) (__info->ctrl_sync)
#define is_available_af(__info) (__info->ver.af)
#define is_code(__code, __type) (__code == m5mols_default_ffmt[__type].code)
#define is_manufacturer(__info, __manufacturer) \
......@@ -285,7 +286,7 @@ int m5mols_mode(struct m5mols_info *info, u8 mode);
int m5mols_enable_interrupt(struct v4l2_subdev *sd, u8 reg);
int m5mols_wait_interrupt(struct v4l2_subdev *sd, u8 condition, u32 timeout);
int m5mols_sync_controls(struct m5mols_info *info);
int m5mols_restore_controls(struct m5mols_info *info);
int m5mols_start_capture(struct m5mols_info *info);
int m5mols_do_scenemode(struct m5mols_info *info, u8 mode);
int m5mols_lock_3a(struct m5mols_info *info, bool lock);
......
......@@ -116,7 +116,7 @@ int m5mols_start_capture(struct m5mols_info *info)
*/
ret = m5mols_mode(info, REG_MONITOR);
if (!ret)
ret = m5mols_sync_controls(info);
ret = m5mols_restore_controls(info);
if (!ret)
ret = m5mols_write(sd, CAPP_YUVOUT_MAIN, REG_JPEG);
if (!ret)
......
......@@ -611,26 +611,25 @@ static struct v4l2_subdev_pad_ops m5mols_pad_ops = {
};
/**
* m5mols_sync_controls - Apply default scene mode and the current controls
* m5mols_restore_controls - Apply current control values to the registers
*
* This is used only streaming for syncing between v4l2_ctrl framework and
* m5mols's controls. First, do the scenemode to the sensor, then call
* v4l2_ctrl_handler_setup. It can be same between some commands and
* the scenemode's in the default v4l2_ctrls. But, such commands of control
* should be prior to the scenemode's one.
* m5mols_do_scenemode() handles all parameters for which there is yet no
* individual control. It should be replaced at some point by setting each
* control individually, in required register set up order.
*/
int m5mols_sync_controls(struct m5mols_info *info)
int m5mols_restore_controls(struct m5mols_info *info)
{
int ret = -EINVAL;
int ret;
if (info->ctrl_sync)
return 0;
if (!is_ctrl_synced(info)) {
ret = m5mols_do_scenemode(info, REG_SCENE_NORMAL);
if (ret)
return ret;
v4l2_ctrl_handler_setup(&info->handle);
info->ctrl_sync = 1;
}
ret = v4l2_ctrl_handler_setup(&info->handle);
info->ctrl_sync = !ret;
return ret;
}
......@@ -654,7 +653,7 @@ static int m5mols_start_monitor(struct m5mols_info *info)
if (!ret)
ret = m5mols_mode(info, REG_MONITOR);
if (!ret)
ret = m5mols_sync_controls(info);
ret = m5mols_restore_controls(info);
return ret;
}
......
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment