staging: brcm80211: cleanup on the brcm80211 include directory

moved several files to specific source directory as these do not
need to be shared between drivers. Also removed some unused include
files from the include directory.
Reviewed-by: Brett Rudley <brudley@broadcom.com>
Reviewed-by: Henry Ptasinski <henryp@broadcom.com>
Reviewed-by: Roland Vossen <rvossen@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

drivers/staging/brcm80211/brcmsmac/Makefile

@@ -25,6 +25,7 @@ ccflags-y :=					\
 	-DDBAND					\
 	-DBCMDMA32				\
 	-DBCMNVRAMR				\
+	-Idrivers/staging/brcm80211/brcmsmac    \
 	-Idrivers/staging/brcm80211/brcmsmac/sys \
 	-Idrivers/staging/brcm80211/brcmsmac/phy \
 	-Idrivers/staging/brcm80211/util \

drivers/staging/brcm80211/brcmsmac/sys/wlc_event.c

@@ -33,9 +33,6 @@
 #include <d11.h>
 #include <wlc_rate.h>
 #include <wlc_mac80211.h>
-#ifdef MSGTRACE
-#include <msgtrace.h>
-#endif
 #include <wl_dbg.h>
 
 /* Local prototypes */

drivers/staging/brcm80211/include/rpc_osl.h

-/*
- * Copyright (c) 2010 Broadcom Corporation
- *
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
- * copyright notice and this permission notice appear in all copies.
- *
- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
- * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
- * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
- * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
- * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
- * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
- */
-
-#ifndef _rpcosl_h_
-#define _rpcosl_h_
-
-typedef struct rpc_osl rpc_osl_t;
-extern rpc_osl_t *rpc_osl_attach(struct osl_info *osh);
-extern void rpc_osl_detach(rpc_osl_t *rpc_osh);
-
-#define RPC_OSL_LOCK(rpc_osh) rpc_osl_lock((rpc_osh))
-#define RPC_OSL_UNLOCK(rpc_osh) rpc_osl_unlock((rpc_osh))
-#define RPC_OSL_WAIT(rpc_osh, to, ptimedout)	rpc_osl_wait((rpc_osh), (to), (ptimedout))
-#define RPC_OSL_WAKE(rpc_osh)			rpc_osl_wake((rpc_osh))
-extern void rpc_osl_lock(rpc_osl_t *rpc_osh);
-extern void rpc_osl_unlock(rpc_osl_t *rpc_osh);
-extern int rpc_osl_wait(rpc_osl_t *rpc_osh, uint ms, bool *ptimedout);
-extern void rpc_osl_wake(rpc_osl_t *rpc_osh);
-
-#endif				/* _rpcosl_h_ */

drivers/staging/brcm80211/include/spid.h

-/*
- * Copyright (c) 2010 Broadcom Corporation
- *
- * Permission to use, copy, modify, and/or distribute this software for any
- * purpose with or without fee is hereby granted, provided that the above
- * copyright notice and this permission notice appear in all copies.
- *
- * THE SOFTWARE IS PROVIDED "AS IS" AND THE AUTHOR DISCLAIMS ALL WARRANTIES
- * WITH REGARD TO THIS SOFTWARE INCLUDING ALL IMPLIED WARRANTIES OF
- * MERCHANTABILITY AND FITNESS. IN NO EVENT SHALL THE AUTHOR BE LIABLE FOR ANY
- * SPECIAL, DIRECT, INDIRECT, OR CONSEQUENTIAL DAMAGES OR ANY DAMAGES
- * WHATSOEVER RESULTING FROM LOSS OF USE, DATA OR PROFITS, WHETHER IN AN ACTION
- * OF CONTRACT, NEGLIGENCE OR OTHER TORTIOUS ACTION, ARISING OUT OF OR IN
- * CONNECTION WITH THE USE OR PERFORMANCE OF THIS SOFTWARE.
- */
-
-#ifndef	_SPI_H
-#define	_SPI_H
-
-/*
- * Brcm SPI Device Register Map.
- *
- */
-
-typedef volatile struct {
-	u8 config;		/* 0x00, len, endian, clock, speed, polarity, wakeup */
-	u8 response_delay;	/* 0x01, read response delay in bytes (corerev < 3) */
-	u8 status_enable;	/* 0x02, status-enable, intr with status, response_delay
-				 * function selection, command/data error check
-				 */
-	u8 reset_bp;		/* 0x03, reset on wlan/bt backplane reset (corerev >= 1) */
-	u16 intr_reg;	/* 0x04, Intr status register */
-	u16 intr_en_reg;	/* 0x06, Intr mask register */
-	u32 status_reg;	/* 0x08, RO, Status bits of last spi transfer */
-	u16 f1_info_reg;	/* 0x0c, RO, enabled, ready for data transfer, blocksize */
-	u16 f2_info_reg;	/* 0x0e, RO, enabled, ready for data transfer, blocksize */
-	u16 f3_info_reg;	/* 0x10, RO, enabled, ready for data transfer, blocksize */
-	u32 test_read;	/* 0x14, RO 0xfeedbead signature */
-	u32 test_rw;		/* 0x18, RW */
-	u8 resp_delay_f0;	/* 0x1c, read resp delay bytes for F0 (corerev >= 3) */
-	u8 resp_delay_f1;	/* 0x1d, read resp delay bytes for F1 (corerev >= 3) */
-	u8 resp_delay_f2;	/* 0x1e, read resp delay bytes for F2 (corerev >= 3) */
-	u8 resp_delay_f3;	/* 0x1f, read resp delay bytes for F3 (corerev >= 3) */
-} spi_regs_t;
-
-/* SPI device register offsets */
-#define SPID_CONFIG			0x00
-#define SPID_RESPONSE_DELAY		0x01
-#define SPID_STATUS_ENABLE		0x02
-#define SPID_RESET_BP			0x03	/* (corerev >= 1) */
-#define SPID_INTR_REG			0x04	/* 16 bits - Interrupt status */
-#define SPID_INTR_EN_REG		0x06	/* 16 bits - Interrupt mask */
-#define SPID_STATUS_REG			0x08	/* 32 bits */
-#define SPID_F1_INFO_REG		0x0C	/* 16 bits */
-#define SPID_F2_INFO_REG		0x0E	/* 16 bits */
-#define SPID_F3_INFO_REG		0x10	/* 16 bits */
-#define SPID_TEST_READ			0x14	/* 32 bits */
-#define SPID_TEST_RW			0x18	/* 32 bits */
-#define SPID_RESP_DELAY_F0		0x1c	/* 8 bits (corerev >= 3) */
-#define SPID_RESP_DELAY_F1		0x1d	/* 8 bits (corerev >= 3) */
-#define SPID_RESP_DELAY_F2		0x1e	/* 8 bits (corerev >= 3) */
-#define SPID_RESP_DELAY_F3		0x1f	/* 8 bits (corerev >= 3) */
-
-/* Bit masks for SPID_CONFIG device register */
-#define WORD_LENGTH_32	0x1	/* 0/1 16/32 bit word length */
-#define ENDIAN_BIG	0x2	/* 0/1 Little/Big Endian */
-#define CLOCK_PHASE	0x4	/* 0/1 clock phase delay */
-#define CLOCK_POLARITY	0x8	/* 0/1 Idle state clock polarity is low/high */
-#define HIGH_SPEED_MODE	0x10	/* 1/0 High Speed mode / Normal mode */
-#define INTR_POLARITY	0x20	/* 1/0 Interrupt active polarity is high/low */
-#define WAKE_UP		0x80	/* 0/1 Wake-up command from Host to WLAN */
-
-/* Bit mask for SPID_RESPONSE_DELAY device register */
-#define RESPONSE_DELAY_MASK	0xFF	/* Configurable rd response delay in multiples of 8 bits */
-
-/* Bit mask for SPID_STATUS_ENABLE device register */
-#define STATUS_ENABLE		0x1	/* 1/0 Status sent/not sent to host after read/write */
-#define INTR_WITH_STATUS	0x2	/* 0/1 Do-not / do-interrupt if status is sent */
-#define RESP_DELAY_ALL		0x4	/* Applicability of resp delay to F1 or all func's read */
-#define DWORD_PKT_LEN_EN	0x8	/* Packet len denoted in dwords instead of bytes */
-#define CMD_ERR_CHK_EN		0x20	/* Command error check enable */
-#define DATA_ERR_CHK_EN		0x40	/* Data error check enable */
-
-/* Bit mask for SPID_RESET_BP device register */
-#define RESET_ON_WLAN_BP_RESET	0x4	/* enable reset for WLAN backplane */
-#define RESET_ON_BT_BP_RESET	0x8	/* enable reset for BT backplane */
-#define RESET_SPI		0x80	/* reset the above enabled logic */
-
-/* Bit mask for SPID_INTR_REG device register */
-#define DATA_UNAVAILABLE	0x0001	/* Requested data not available; Clear by writing a "1" */
-#define F2_F3_FIFO_RD_UNDERFLOW	0x0002
-#define F2_F3_FIFO_WR_OVERFLOW	0x0004
-#define COMMAND_ERROR		0x0008	/* Cleared by writing 1 */
-#define DATA_ERROR		0x0010	/* Cleared by writing 1 */
-#define F2_PACKET_AVAILABLE	0x0020
-#define F3_PACKET_AVAILABLE	0x0040
-#define F1_OVERFLOW		0x0080	/* Due to last write. Bkplane has pending write requests */
-#define MISC_INTR0		0x0100
-#define MISC_INTR1		0x0200
-#define MISC_INTR2		0x0400
-#define MISC_INTR3		0x0800
-#define MISC_INTR4		0x1000
-#define F1_INTR			0x2000
-#define F2_INTR			0x4000
-#define F3_INTR			0x8000
-
-/* Bit mask for 32bit SPID_STATUS_REG device register */
-#define STATUS_DATA_NOT_AVAILABLE	0x00000001
-#define STATUS_UNDERFLOW		0x00000002
-#define STATUS_OVERFLOW			0x00000004
-#define STATUS_F2_INTR			0x00000008
-#define STATUS_F3_INTR			0x00000010
-#define STATUS_F2_RX_READY		0x00000020
-#define STATUS_F3_RX_READY		0x00000040
-#define STATUS_HOST_CMD_DATA_ERR	0x00000080
-#define STATUS_F2_PKT_AVAILABLE		0x00000100
-#define STATUS_F2_PKT_LEN_MASK		0x000FFE00
-#define STATUS_F2_PKT_LEN_SHIFT		9
-#define STATUS_F3_PKT_AVAILABLE		0x00100000
-#define STATUS_F3_PKT_LEN_MASK		0xFFE00000
-#define STATUS_F3_PKT_LEN_SHIFT		21
-
-/* Bit mask for 16 bits SPID_F1_INFO_REG device register */
-#define F1_ENABLED 			0x0001
-#define F1_RDY_FOR_DATA_TRANSFER	0x0002
-#define F1_MAX_PKT_SIZE			0x01FC
-
-/* Bit mask for 16 bits SPID_F2_INFO_REG device register */
-#define F2_ENABLED 			0x0001
-#define F2_RDY_FOR_DATA_TRANSFER	0x0002
-#define F2_MAX_PKT_SIZE			0x3FFC
-
-/* Bit mask for 16 bits SPID_F3_INFO_REG device register */
-#define F3_ENABLED 			0x0001
-#define F3_RDY_FOR_DATA_TRANSFER	0x0002
-#define F3_MAX_PKT_SIZE			0x3FFC
-
-/* Bit mask for 32 bits SPID_TEST_READ device register read in 16bit LE mode */
-#define TEST_RO_DATA_32BIT_LE		0xFEEDBEAD
-
-/* Maximum number of I/O funcs */
-#define SPI_MAX_IOFUNCS		4
-
-#define SPI_MAX_PKT_LEN		(2048*4)
-
-/* Misc defines */
-#define SPI_FUNC_0		0
-#define SPI_FUNC_1		1
-#define SPI_FUNC_2		2
-#define SPI_FUNC_3		3
-
-#define WAIT_F2RXFIFORDY	100
-#define WAIT_F2RXFIFORDY_DELAY	20
-
-#endif				/* _SPI_H */