ARM: dts: kirkwood: split lswvl dts to linkstation lsvl and lswvl

LS-WVL/VL are both kirkwood-6282 based NAS devices, which share
many MPP pins. However they are slightly different:
  - LS-WVL is 2-Bay NAS, and LS-VL is only 1-Bay.
  - There're two red LED indicator on LS-WVL to show when HDD fails,
    which is similar to LS-WXL, but there's no such on LS-VL.

So after the split, common part goes into .dtsi file:
  - kirkwood-linkstation-6282.dtsi
while all rest part goes into device specific .dts file:
  - kirkwood-linkstation-lsvl.dts
  - kirkwood-linkstation-lswvl.dts
Signed-off-by: Roger Shimizu <rogershimizu@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>

Documentation/devicetree/bindings/arm/marvell,kirkwood.txt

@@ -19,10 +19,11 @@ SoC. Currently known SoC compatibles are:
 And in addition, the compatible shall be extended with the specific
 board. Currently known boards are:
 
+"buffalo,linkstation-lsvl"
 "buffalo,linkstation-lswsxl"
 "buffalo,linkstation-lswxl"
+"buffalo,linkstation-lswvl"
 "buffalo,lschlv2"
-"buffalo,lswvl"
 "buffalo,lsxhl"
 "buffalo,lsxl"
 "cloudengines,pogo02"

arch/arm/boot/dts/Makefile

@@ -189,10 +189,11 @@ dtb-$(CONFIG_MACH_KIRKWOOD) += \
 	kirkwood-is2.dtb \
 	kirkwood-km_kirkwood.dtb \
 	kirkwood-laplug.dtb \
+	kirkwood-linkstation-lsvl.dtb \
 	kirkwood-linkstation-lswsxl.dtb \
+	kirkwood-linkstation-lswvl.dtb \
 	kirkwood-linkstation-lswxl.dtb \
 	kirkwood-lschlv2.dtb \
-	kirkwood-lswvl.dtb \
 	kirkwood-lsxhl.dtb \
 	kirkwood-mplcec4.dtb \
 	kirkwood-mv88f6281gtw-ge.dtb \

arch/arm/boot/dts/kirkwood-lswvl.dts → arch/arm/boot/dts/kirkwood-linkstation-6282.dtsi

 /*
- * Device Tree file for Buffalo Linkstation LS-WVL/VL
+ * Device Tree common file for kirkwood-6282 based Buffalo Linkstation
  *
  * Copyright (C) 2015, 2016
  * Roger Shimizu <rogershimizu@gmail.com>
@@ -43,44 +43,17 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-
 #include "kirkwood.dtsi"
 #include "kirkwood-6282.dtsi"
+#include "kirkwood-linkstation.dtsi"
 
 / {
-	model = "Buffalo Linkstation LS-WVL/VL";
-	compatible = "buffalo,lswvl", "buffalo,lsvl", "marvell,kirkwood-88f6282", "marvell,kirkwood";
-
-	memory { /* 256 MB */
-		device_type = "memory";
-		reg = <0x00000000 0x10000000>;
-	};
-
-	chosen {
-		bootargs = "console=ttyS0,115200n8 earlyprintk";
-		stdout-path = &uart0;
-	};
-
-	mbus {
-		pcie-controller {
-			status = "okay";
-			pcie@1,0 {
-				status = "okay";
-			};
-		};
-	};
-
 	ocp@f1000000 {
 		pinctrl: pin-controller@10000 {
 			pmx_power_hdd0: pmx-power-hdd0 {
 				marvell,pins = "mpp8";
 				marvell,function = "gpio";
 			};
-			pmx_power_hdd1: pmx-power-hdd1 {
-				marvell,pins = "mpp9";
-				marvell,function = "gpio";
-			};
 			pmx_usb_vbus: pmx-usb-vbus {
 				marvell,pins = "mpp12";
 				marvell,function = "gpio";
@@ -93,14 +66,6 @@ pmx_fan_low: pmx-fan-low {
 				marvell,pins = "mpp17";
 				marvell,function = "gpio";
 			};
-			pmx_led_hdderr0: pmx-led-hdderr0 {
-				marvell,pins = "mpp34";
-				marvell,function = "gpio";
-			};
-			pmx_led_hdderr1: pmx-led-hdderr1 {
-				marvell,pins = "mpp35";
-				marvell,function = "gpio";
-			};
 			pmx_led_alarm: pmx-led-alarm {
 				marvell,pins = "mpp36";
 				marvell,function = "gpio";
@@ -138,120 +103,48 @@ pmx_power_auto_switch: pmx-power-auto-switch {
 				marvell,function = "gpio";
 			};
 		};
-
-		serial@12000 {
-			status = "okay";
-		};
-
-		sata@80000 {
-			status = "okay";
-			nr-ports = <2>;
-		};
-
-		spi@10600 {
-			status = "okay";
-
-			m25p40@0 {
-				#address-cells = <1>;
-				#size-cells = <1>;
-				compatible = "st,m25p40", "jedec,spi-nor";
-				reg = <0>;
-				spi-max-frequency = <25000000>;
-				mode = <0>;
-
-				partition@0 {
-					reg = <0x0 0x60000>;
-					label = "uboot";
-					read-only;
-				};
-
-				partition@60000 {
-					reg = <0x60000 0x10000>;
-					label = "dtb";
-					read-only;
-				};
-
-				partition@70000 {
-					reg = <0x70000 0x10000>;
-					label = "uboot_env";
-				};
-			};
-		};
 	};
 
 	gpio_keys {
-		compatible = "gpio-keys";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&pmx_button_function &pmx_power_switch
-			     &pmx_power_auto_switch>;
-		pinctrl-names = "default";
-
-		button@1 {
-			label = "Function Button";
-			linux,code = <KEY_OPTION>;
+		function-button {
 			gpios = <&gpio1 13 GPIO_ACTIVE_LOW>;
 		};
 
-		button@2 {
-			label = "Power-on Switch";
-			linux,code = <KEY_RESERVED>;
-			linux,input-type = <5>;
+		power-on-switch {
 			gpios = <&gpio1 14 GPIO_ACTIVE_LOW>;
 		};
 
-		button@3 {
-			label = "Power-auto Switch";
-			linux,code = <KEY_ESC>;
-			linux,input-type = <5>;
+		power-auto-switch {
 			gpios = <&gpio1 15 GPIO_ACTIVE_LOW>;
 		};
 	};
 
 	gpio_leds {
-		compatible = "gpio-leds";
-		pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
-			     &pmx_led_info &pmx_led_power
-			     &pmx_led_function_blue
-			     &pmx_led_hdderr0
-			     &pmx_led_hdderr1>;
-		pinctrl-names = "default";
-
-		led@1 {
-			label = "lswvl:red:alarm";
+		red-alarm-led {
+			label = "linkstation:red:alarm";
 			gpios = <&gpio1 4 GPIO_ACTIVE_HIGH>;
 		};
 
-		led@2 {
-			label = "lswvl:red:func";
+		red-function-led {
+			label = "linkstation:red:function";
 			gpios = <&gpio1 5 GPIO_ACTIVE_HIGH>;
 		};
 
-		led@3 {
-			label = "lswvl:amber:info";
+		amber-info-led {
+			label = "linkstation:amber:info";
 			gpios = <&gpio1 6 GPIO_ACTIVE_HIGH>;
 		};
 
-		led@4 {
-			label = "lswvl:blue:func";
+		blue-function-led {
+			label = "linkstation:blue:function";
 			gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>;
 		};
 
-		led@5 {
-			label = "lswvl:blue:power";
+		blue-power-led {
+			label = "linkstation:blue:power";
 			gpios = <&gpio1 8 GPIO_ACTIVE_LOW>;
 			default-state = "keep";
 		};
-
-		led@6 {
-			label = "lswvl:red:hdderr0";
-			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
-		};
-
-		led@7 {
-			label = "lswvl:red:hdderr1";
-			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
-		};
 	};
 
 	gpio_fan {
@@ -270,50 +163,14 @@ gpio_fan {
 		alarm-gpios = <&gpio1 11 GPIO_ACTIVE_HIGH>;
 	};
 
-	restart_poweroff {
-		compatible = "restart-poweroff";
-	};
-
 	regulators {
-		compatible = "simple-bus";
-		#address-cells = <1>;
-		#size-cells = <0>;
-		pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
-		pinctrl-names = "default";
-
 		usb_power: regulator@1 {
-			compatible = "regulator-fixed";
-			reg = <1>;
-			regulator-name = "USB Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
 			gpio = <&gpio0 12 GPIO_ACTIVE_HIGH>;
 		};
+
 		hdd_power0: regulator@2 {
-			compatible = "regulator-fixed";
-			reg = <2>;
-			regulator-name = "HDD0 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
 			gpio = <&gpio0 8 GPIO_ACTIVE_HIGH>;
 		};
-		hdd_power1: regulator@3 {
-			compatible = "regulator-fixed";
-			reg = <3>;
-			regulator-name = "HDD1 Power";
-			regulator-min-microvolt = <5000000>;
-			regulator-max-microvolt = <5000000>;
-			enable-active-high;
-			regulator-always-on;
-			regulator-boot-on;
-			gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
-		};
 	};
 };
 

arch/arm/boot/dts/kirkwood-linkstation-lsvl.dts

+/*
+ * Device Tree file for Buffalo Linkstation LS-VL
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "kirkwood-linkstation-6282.dtsi"
+
+/ {
+	model = "Buffalo Linkstation LS-VL";
+	compatible = "buffalo,lsvl", "marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory { /* 256 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+};

arch/arm/boot/dts/kirkwood-linkstation-lswvl.dts

+/*
+ * Device Tree file for Buffalo Linkstation LS-WVL
+ *
+ * Copyright (C) 2015, 2016
+ * Roger Shimizu <rogershimizu@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED , WITHOUT WARRANTY OF ANY KIND
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "kirkwood-linkstation-6282.dtsi"
+
+/ {
+	model = "Buffalo Linkstation LS-WVL";
+	compatible = "buffalo,lswvl","marvell,kirkwood-88f6282", "marvell,kirkwood";
+
+	memory { /* 256 MB */
+		device_type = "memory";
+		reg = <0x00000000 0x10000000>;
+	};
+
+	ocp@f1000000 {
+		pinctrl: pin-controller@10000 {
+			pmx_power_hdd1: pmx-power-hdd1 {
+				marvell,pins = "mpp9";
+				marvell,function = "gpio";
+			};
+			pmx_led_hdderr0: pmx-led-hdderr0 {
+				marvell,pins = "mpp34";
+				marvell,function = "gpio";
+			};
+			pmx_led_hdderr1: pmx-led-hdderr1 {
+				marvell,pins = "mpp35";
+				marvell,function = "gpio";
+			};
+		};
+
+		sata@80000 {
+			nr-ports = <2>;
+		};
+	};
+
+	gpio_leds {
+		pinctrl-0 = <&pmx_led_function_red &pmx_led_alarm
+			     &pmx_led_info &pmx_led_power
+			     &pmx_led_function_blue
+			     &pmx_led_hdderr0
+			     &pmx_led_hdderr1>;
+
+		red-hdderr0-led {
+			label = "linkstation:red:hdderr0";
+			gpios = <&gpio1 2 GPIO_ACTIVE_HIGH>;
+		};
+
+		red-hdderr1-led {
+			label = "linkstation:red:hdderr1";
+			gpios = <&gpio1 3 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
+	regulators {
+		pinctrl-0 = <&pmx_power_hdd0 &pmx_power_hdd1 &pmx_usb_vbus>;
+
+		hdd_power1: regulator@3 {
+			compatible = "regulator-fixed";
+			reg = <3>;
+			regulator-name = "HDD1 Power";
+			regulator-min-microvolt = <5000000>;
+			regulator-max-microvolt = <5000000>;
+			enable-active-high;
+			regulator-always-on;
+			regulator-boot-on;
+			gpio = <&gpio0 9 GPIO_ACTIVE_HIGH>;
+		};
+	};
+};