Commit 62a03310 authored by Kai Germaschewski's avatar Kai Germaschewski

Split up drivers/isdn/Config.help and drivers/isdn/i4l/Config.in

parent affc4333
......@@ -11,502 +11,3 @@ CONFIG_ISDN_BOOL
Select this option if you want your kernel to support ISDN.
CONFIG_ISDN
This driver allows you to use an ISDN-card for networking
connections and as dialin/out device. The isdn-tty's have a built
in AT-compatible modem emulator. Network devices support autodial,
channel-bundling, callback and caller-authentication without having
a daemon running. A reduced T.70 protocol is supported with tty's
suitable for German BTX. On D-Channel, the protocols EDSS1
(Euro-ISDN) and 1TR6 (German style) are supported. See
<file:Documentation/isdn/README> for more information.
ISDN support in the linux kernel is moving towards a new API,
called CAPI (Common ISDN Application Programming Interface).
Therefore the old ISDN4Linux layer is becoming obsolete. It is
still usable, though, if you select this option.
CONFIG_ISDN_PPP
Over digital connections such as ISDN, there is no need to
synchronize sender and recipient's clocks with start and stop bits
as is done over analog telephone lines. Instead, one can use
"synchronous PPP". Saying Y here will include this protocol. This
protocol is used by Cisco and Sun for example. So you want to say Y
here if the other end of your ISDN connection supports it. You will
need a special version of pppd (called ipppd) for using this
feature. See <file:Documentation/isdn/README.syncppp> and
<file:Documentation/isdn/syncPPP.FAQ> for more information.
CONFIG_ISDN_MPP
With synchronous PPP enabled, it is possible to increase throughput
by bundling several ISDN-connections, using this protocol. See
<file:Documentation/isdn/README.syncppp> for more information.
CONFIG_ISDN_PPP_VJ
This enables Van Jacobson header compression for synchronous PPP.
Say Y if the other end of the connection supports it.
CONFIG_ISDN_PPP_BSDCOMP
Support for the BSD-Compress compression method for PPP, which uses
the LZW compression method to compress each PPP packet before it is
sent over the wire. The machine at the other end of the PPP link
(usually your ISP) has to support the BSD-Compress compression
method as well for this to be useful. Even if they don't support it,
it is safe to say Y here.
CONFIG_ISDN_AUDIO
If you say Y here, the modem-emulator will support a subset of the
EIA Class 8 Voice commands. Using a getty with voice-support
(mgetty+sendfax by gert@greenie.muc.de with an extension, available
with the ISDN utility package for example), you will be able to use
your Linux box as an ISDN-answering machine. Of course, this must be
supported by the lowlevel driver also. Currently, the HiSax driver
is the only voice-supporting driver. See
<file:Documentation/isdn/README.audio> for more information.
CONFIG_ISDN_X25
This feature provides the X.25 protocol over ISDN connections.
See <file:Documentation/isdn/README.x25> for more information
if you are thinking about using this.
CONFIG_ISDN_DIVERSION
This option allows you to use some supplementary diversion
services in conjunction with the HiSax driver on an EURO/DSS1
line.
Supported options are CD (call deflection), CFU (Call forward
unconditional), CFB (Call forward when busy) and CFNR (call forward
not reachable). Additionally the actual CFU, CFB and CFNR state may
be interrogated.
The use of CFU, CFB, CFNR and interrogation may be limited to some
countries. The keypad protocol is still not implemented. CD should
work in all countries if the service has been subscribed to.
Please read the file <file:Documentation/isdn/README.diversion>.
CONFIG_ISDN_DRV_ICN
This enables support for two kinds of ISDN-cards made by a German
company called ICN. 2B is the standard version for a single ISDN
line with two B-channels, 4B supports two ISDN lines. For running
this card, additional firmware is necessary, which has to be
downloaded into the card using a utility which is distributed
separately. See <file:Documentation/isdn/README> and
<file:Documentation/isdn/README.icn> for more
information.
CONFIG_ISDN_DRV_LOOP
This driver provides a virtual ISDN card. Its primary purpose is
testing of linklevel features or configuration without getting
charged by your service-provider for lots of phone calls.
You need will need the loopctrl utility from the latest isdn4k-utils
package to set up this driver.
CONFIG_ISDN_DRV_HISAX
This is a driver supporting the Siemens chipset on various
ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles
S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many
compatibles).
HiSax is just the name of this driver, not the name of any hardware.
If you have a card with such a chipset, you should say Y here and
also to the configuration option of the driver for your particular
card, below.
CONFIG_HISAX_EURO
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
The call control protocol E-DSS1 is used in most European countries.
If unsure, say Y.
CONFIG_DE_AOC
If you want that the HiSax hardware driver sends messages to the
upper level of the isdn code on each AOCD (Advice Of Charge, During
the call -- transmission of the fee information during a call) and
on each AOCE (Advice Of Charge, at the End of the call --
transmission of fee information at the end of the call), say Y here.
This works only in Germany.
CONFIG_HISAX_NO_SENDCOMPLETE
If you have trouble with some ugly exchanges or you live in
Australia select this option.
CONFIG_HISAX_NO_LLC
If you have trouble with some ugly exchanges try to select this
option.
CONFIG_HISAX_NO_KEYPAD
If you like to send special dial strings including * or # without
using the keypad protocol, select this option.
CONFIG_HISAX_1TR6
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
1TR6 is an old call control protocol which was used in Germany
before E-DSS1 was established. Nowadays, all new lines in Germany
use E-DSS1.
CONFIG_HISAX_NI1
Enable this if you like to use ISDN in US on a NI1 basic rate
interface.
CONFIG_HISAX_MAX_CARDS
This option allows you to specify the maximum number of cards which
the HiSax driver will be able to handle.
CONFIG_HISAX_16_0
This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8
and many compatibles.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port/shmem settings.
CONFIG_HISAX_16_3
This enables HiSax support for the Teles ISDN-cards S0-16.3 the
Teles/Creatix PnP and the Teles PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_TELESPCI
This enables HiSax support for the Teles PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_S0BOX
This enables HiSax support for the Teles/Creatix parallel port
S0BOX. See <file:Documentation/isdn/README.HiSax> on how to
configure it.
CONFIG_HISAX_AVM_A1
This enables HiSax support for the AVM A1 (aka "Fritz").
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_FRITZPCI
This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI".
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_AVM_A1_PCMCIA
This enables HiSax support for the AVM A1 "Fritz!PCMCIA").
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_ELSA
This enables HiSax support for the Elsa Mircolink ISA cards, for the
Elsa Quickstep series cards and Elsa PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_IX1MICROR2
This enables HiSax support for the ITK ix1-micro Revision 2 card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_DIEHLDIVA
This enables HiSax support for the Eicon.Diehl Diva none PRO
versions passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_ASUSCOM
This enables HiSax support for the AsusCom and their OEM versions
passive ISDN ISA cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_TELEINT
This enables HiSax support for the TELEINT SA1 semiactiv ISDN card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_HFCS
This enables HiSax support for the HFC-S 2BDS0 based cards, like
teles 16.3c.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_SEDLBAUER
This enables HiSax support for the Sedlbauer passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_SPORTSTER
This enables HiSax support for the USR Sportster internal TA card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_MIC
This enables HiSax support for the ITH MIC card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NETJET
This enables HiSax support for the NetJet from Traverse
Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NETJET_U
This enables HiSax support for the Netspider U interface ISDN card
from Traverse Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NICCY
This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_ISURF
This enables HiSax support for the Siemens I-Talk/I-Surf card with
ISAR chip.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HSTSAPHIR
This enables HiSax support for the HST Saphir card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_BKM_A4T
This enables HiSax support for the Telekom A4T card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_SCT_QUADRO
This enables HiSax support for the Scitel Quadro card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_GAZEL
This enables HiSax support for the Gazel cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HFC_PCI
This enables HiSax support for the HFC-S PCI 2BDS0 based cards.
For more informations see under
<file:Documentation/isdn/README.hfc-pci>.
CONFIG_HISAX_W6692
This enables HiSax support for Winbond W6692 based PCI ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HFC_SX
This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA
cards. This code is not finished yet.
CONFIG_HISAX_AMD7930
This enables HiSax support for the AMD7930 chips on some SPARCs.
This code is not finished yet.
CONFIG_HISAX_DEBUG
This enables debugging code in the new-style HiSax drivers, i.e.
the ST5481 USB driver currently.
If in doubt, say yes.
CONFIG_HISAX_ELSA_CS
This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink
card.
CONFIG_HISAX_SEDLBAUER_CS
This enables the PCMCIA client driver for the Sedlbauer Speed Star
and Speed Star II cards.
CONFIG_HISAX_ST5481
This enables the driver for ST5481 based USB ISDN adapters,
e.g. the BeWan Gazel 128 USB
CONFIG_HISAX_FRITZ_PCIPNP
This enables the driver for the AVM Fritz!Card PCI, Fritz!Card PCI v2
and Fritz!Card PnP.
(the latter also needs you to select "ISA Plug and Play support"
from the menu "Plug and Play configuration")
CONFIG_HISAX_FRITZ_CLASSIC
This enables the driver for the AVM Fritz!Card classic, formerly
known as AVM A1.
CONFIG_ISDN_DRV_PCBIT
This enables support for the PCBIT ISDN-card. This card is
manufactured in Portugal by Octal. For running this card,
additional firmware is necessary, which has to be downloaded into
the card using a utility which is distributed separately. See
<file:Documentation/isdn/README> and
<file:Documentation/isdn/README.pcbit> for more information.
CONFIG_ISDN_DRV_SC
This enables support for the Spellcaster BRI ISDN boards. This
driver currently builds only in a modularized version ( = code which
can be inserted in and removed from the running kernel whenever you
want, details in <file:Documentation/modules.txt>); the module will
be called sc.o. See <file:Documentation/isdn/README.sc> and
<http://www.spellcast.com/> for more information.
CONFIG_ISDN_DRV_EICON
Say Y here if you have an Eicon active ISDN card. In order to use
this card, additional firmware is necessary, which has to be loaded
into the card using the eiconctrl utility which is part of the
latest isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.eicon> for more information.
CONFIG_ISDN_DRV_EICON_OLD
Say Y here to use your Eicon active ISDN card with ISDN4Linux
isdn module.
CONFIG_ISDN_DRV_EICON_PCI
Say Y here if you have an Eicon Diva Server (BRI/PRI/4BRI) ISDN
card. Please read <file:Documentation/isdn/README.eicon> for more
information.
CONFIG_ISDN_DRV_EICON_ISA
Say Y here if you have an old-type Eicon active ISDN card. In order
to use this card, additional firmware is necessary, which has to be
loaded into the card using the eiconctrl utility which is part of
the latest isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.eicon> for more information.
CONFIG_ISDN_DRV_EICON_DIVAS
Enable this option if you want the eicon driver as standalone
version with no interface to the ISDN4Linux isdn module. If you
say Y here, the eicon module only supports the Diva Server PCI
cards and will provide its own IDI interface. You should say N
here.
CONFIG_ISDN_TTY_FAX
If you say Y here, the modem-emulator will support a subset of the
Fax Class 1 and 2 commands. Using a getty with fax-support
(mgetty+sendfax, hylafax), you will be able to use your Linux box as
an ISDN-fax-machine. This must be supported by the lowlevel driver
also. See <file:Documentation/isdn/README.fax> for more information.
CONFIG_ISDN_CAPI
This provides the CAPI (Common ISDN Application Programming
Interface, a standard making it easy for programs to access ISDN
hardware, see <http://www.capi.org/>. This is needed for AVM's set
of active ISDN controllers like B1, T1, M1.
CONFIG_ISDN_CAPI_CAPI20
This option will provide the CAPI 2.0 interface to userspace
applications via /dev/capi20. Applications should use the
standardized libcapi20 to access this functionality. You should say
Y/M here.
CONFIG_ISDN_CAPI_MIDDLEWARE
This option will enhance the capabilities of the /dev/capi20
interface. It will provide a means of moving a data connection,
established via the usual /dev/capi20 interface to a special tty
device. If you want to use pppd with pppdcapiplugin to dial up to
your ISP, say Y here.
CONFIG_ISDN_CAPI_CAPIFS
This option provides a special file system, similar to /dev/pts with
device nodes for the special ttys established by using the
middleware extension above. If you want to use pppd with
pppdcapiplugin to dial up to your ISP, say Y here.
CONFIG_ISDN_CAPI_CAPIDRV
This option provides the glue code to hook up CAPI driven cards to
the legacy isdn4linux link layer. If you have a card which is
supported by a CAPI driver, but still want to use old features like
ippp interfaces or ttyI emulation, say Y/M here.
CONFIG_ISDN_DRV_AVMB1_B1ISA
Enable support for the ISA version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_B1PCI
Enable support for the PCI version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_B1PCIV4
Enable support for the V4 version of AVM B1 PCI card.
CONFIG_ISDN_DRV_AVMB1_T1ISA
Enable support for the AVM T1 T1B card.
Note: This is a PRI card and handle 30 B-channels.
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA
Enable support for the PCMCIA version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_AVM_CS
Enable the PCMCIA client driver for the AVM B1/M1/M2
PCMCIA cards.
CONFIG_ISDN_DRV_AVMB1_T1PCI
Enable support for the AVM T1 T1B card.
Note: This is a PRI card and handle 30 B-channels.
CONFIG_ISDN_DRV_AVMB1_C4
Enable support for the AVM C4/C2 PCI cards.
These cards handle 4/2 BRI ISDN lines (8/4 channels).
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON
If you say Y here, the AVM B1 driver will give verbose reasons for
disconnecting. This will increase the size of the kernel by 7 KB. If
unsure, say Y.
CONFIG_ISDN_DRV_ACT2000
Say Y here if you have an IBM Active 2000 ISDN card. In order to use
this card, additional firmware is necessary, which has to be loaded
into the card using a utility which is part of the latest
isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.act2000> for more information.
CONFIG_ISDN_DRV_TPAM
This enables support for the Auvertech TurboPAM ISDN-card.
For running this card, additional firmware is necessary, which has
to be downloaded into the card using a utility which is distributed
separately from the Auvertech's web site: <http://www.auvertech.fr/>.
Please redirect all support questions to support@auvertech.fr.
CONFIG_HYSDN
Say Y here if you have one of Hypercope's active PCI ISDN cards
Champ, Ergo and Metro. You will then get a module called hysdn.o.
Please read the file <file:Documentation/isdn/README.hysdn> for more
information.
CONFIG_HYSDN_CAPI
Say Y here if you like to use Hypercope's CAPI 2.0 interface.
CONFIG_ISDN_DRV_ACT2000
Say Y here if you have an IBM Active 2000 ISDN card. In order to use
this card, additional firmware is necessary, which has to be loaded
into the card using a utility which is part of the latest
isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.act2000> for more information.
#
# Config.in for IBM Active 2000 ISDN driver
#
dep_tristate 'IBM Active 2000 support' CONFIG_ISDN_DRV_ACT2000 $CONFIG_ISDN
CONFIG_ISDN_CAPI
This provides the CAPI (Common ISDN Application Programming
Interface, a standard making it easy for programs to access ISDN
hardware, see <http://www.capi.org/>. This is needed for AVM's set
of active ISDN controllers like B1, T1, M1.
CONFIG_ISDN_CAPI_CAPI20
This option will provide the CAPI 2.0 interface to userspace
applications via /dev/capi20. Applications should use the
standardized libcapi20 to access this functionality. You should say
Y/M here.
CONFIG_ISDN_CAPI_MIDDLEWARE
This option will enhance the capabilities of the /dev/capi20
interface. It will provide a means of moving a data connection,
established via the usual /dev/capi20 interface to a special tty
device. If you want to use pppd with pppdcapiplugin to dial up to
your ISP, say Y here.
CONFIG_ISDN_CAPI_CAPIFS
This option provides a special file system, similar to /dev/pts with
device nodes for the special ttys established by using the
middleware extension above. If you want to use pppd with
pppdcapiplugin to dial up to your ISP, say Y here.
CONFIG_ISDN_CAPI_CAPIDRV
This option provides the glue code to hook up CAPI driven cards to
the legacy isdn4linux link layer. If you have a card which is
supported by a CAPI driver, but still want to use old features like
ippp interfaces or ttyI emulation, say Y/M here.
CONFIG_ISDN_DRV_AVMB1_B1ISA
Enable support for the ISA version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_B1PCI
Enable support for the PCI version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_B1PCIV4
Enable support for the V4 version of AVM B1 PCI card.
CONFIG_ISDN_DRV_AVMB1_T1ISA
Enable support for the AVM T1 T1B card.
Note: This is a PRI card and handle 30 B-channels.
CONFIG_ISDN_DRV_AVMB1_B1PCMCIA
Enable support for the PCMCIA version of the AVM B1 card.
CONFIG_ISDN_DRV_AVMB1_AVM_CS
Enable the PCMCIA client driver for the AVM B1/M1/M2
PCMCIA cards.
CONFIG_ISDN_DRV_AVMB1_T1PCI
Enable support for the AVM T1 T1B card.
Note: This is a PRI card and handle 30 B-channels.
CONFIG_ISDN_DRV_AVMB1_C4
Enable support for the AVM C4/C2 PCI cards.
These cards handle 4/2 BRI ISDN lines (8/4 channels).
CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON
If you say Y here, the AVM B1 driver will give verbose reasons for
disconnecting. This will increase the size of the kernel by 7 KB. If
unsure, say Y.
#
# Config.in for the CAPI subsystem
#
tristate 'CAPI2.0 support' CONFIG_ISDN_CAPI
if [ "$CONFIG_ISDN_CAPI" != "n" ]; then
bool ' Verbose reason code reporting (kernel size +=7K)' CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON
dep_bool ' CAPI2.0 Middleware support (EXPERIMENTAL)' CONFIG_ISDN_CAPI_MIDDLEWARE $CONFIG_EXPERIMENTAL
dep_tristate ' CAPI2.0 /dev/capi support' CONFIG_ISDN_CAPI_CAPI20 $CONFIG_ISDN_CAPI
if [ "$CONFIG_ISDN_CAPI_MIDDLEWARE" = "y" ]; then
dep_mbool ' CAPI2.0 filesystem support' CONFIG_ISDN_CAPI_CAPIFS_BOOL $CONFIG_ISDN_CAPI_CAPI20
if [ "$CONFIG_ISDN_CAPI_CAPIFS_BOOL" = "y" ]; then
define_tristate CONFIG_ISDN_CAPI_CAPIFS $CONFIG_ISDN_CAPI_CAPI20
else
define_tristate CONFIG_ISDN_CAPI_CAPIFS n
fi
fi
dep_tristate ' CAPI2.0 capidrv interface support' CONFIG_ISDN_CAPI_CAPIDRV $CONFIG_ISDN_CAPI $CONFIG_ISDN
fi
# CAPI drivers
if [ "$CONFIG_ISDN_CAPI" != "n" ]; then
dep_tristate ' AVM B1 ISA support' CONFIG_ISDN_DRV_AVMB1_B1ISA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1 PCI support' CONFIG_ISDN_DRV_AVMB1_B1PCI $CONFIG_ISDN_CAPI $CONFIG_PCI
dep_mbool ' AVM B1 PCI V4 support' CONFIG_ISDN_DRV_AVMB1_B1PCIV4 $CONFIG_ISDN_DRV_AVMB1_B1PCI
dep_tristate ' AVM T1/T1-B ISA support' CONFIG_ISDN_DRV_AVMB1_T1ISA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1/M1/M2 PCMCIA support' CONFIG_ISDN_DRV_AVMB1_B1PCMCIA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1/M1/M2 PCMCIA cs module' CONFIG_ISDN_DRV_AVMB1_AVM_CS $CONFIG_ISDN_DRV_AVMB1_B1PCMCIA $CONFIG_PCMCIA
dep_tristate ' AVM T1/T1-B PCI support' CONFIG_ISDN_DRV_AVMB1_T1PCI $CONFIG_ISDN_CAPI $CONFIG_PCI
dep_tristate ' AVM C4/C2 support' CONFIG_ISDN_DRV_AVMB1_C4 $CONFIG_ISDN_CAPI $CONFIG_PCI
fi
CONFIG_ISDN_DRV_EICON
Say Y here if you have an Eicon active ISDN card. In order to use
this card, additional firmware is necessary, which has to be loaded
into the card using the eiconctrl utility which is part of the
latest isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.eicon> for more information.
CONFIG_ISDN_DRV_EICON_OLD
Say Y here to use your Eicon active ISDN card with ISDN4Linux
isdn module.
CONFIG_ISDN_DRV_EICON_PCI
Say Y here if you have an Eicon Diva Server (BRI/PRI/4BRI) ISDN
card. Please read <file:Documentation/isdn/README.eicon> for more
information.
CONFIG_ISDN_DRV_EICON_ISA
Say Y here if you have an old-type Eicon active ISDN card. In order
to use this card, additional firmware is necessary, which has to be
loaded into the card using the eiconctrl utility which is part of
the latest isdn4k-utils package. Please read the file
<file:Documentation/isdn/README.eicon> for more information.
CONFIG_ISDN_DRV_EICON_DIVAS
Enable this option if you want the eicon driver as standalone
version with no interface to the ISDN4Linux isdn module. If you
say Y here, the eicon module only supports the Diva Server PCI
cards and will provide its own IDI interface. You should say N
here.
#
# Config.in for Eicon active ISDN support
#
bool 'Eicon active card support' CONFIG_ISDN_DRV_EICON
if [ "$CONFIG_ISDN_DRV_EICON" != "n" ]; then
if [ "$CONFIG_ISDN_DRV_EICON_OLD" != "y" ]; then
dep_tristate ' Build Eicon driver type standalone' CONFIG_ISDN_DRV_EICON_DIVAS $CONFIG_ISDN $CONFIG_PCI
fi
if [ "$CONFIG_ISDN_DRV_EICON_DIVAS" != "y" ]; then
dep_tristate ' Legacy Eicon driver' CONFIG_ISDN_DRV_EICON_OLD $CONFIG_ISDN
if [ "$CONFIG_ISDN_DRV_EICON_OLD" != "n" ]; then
dep_bool ' Eicon PCI DIVA Server BRI/PRI/4BRI support' CONFIG_ISDN_DRV_EICON_PCI $CONFIG_PCI
bool ' Eicon S,SX,SCOM,Quadro,S2M support' CONFIG_ISDN_DRV_EICON_ISA
fi
fi
fi
CONFIG_ISDN_DRV_HISAX
This is a driver supporting the Siemens chipset on various
ISDN-cards (like AVM A1, Elsa ISDN cards, Teles S0-16.0, Teles
S0-16.3, Teles S0-8, Teles/Creatix PnP, ITK micro ix1 and many
compatibles).
HiSax is just the name of this driver, not the name of any hardware.
If you have a card with such a chipset, you should say Y here and
also to the configuration option of the driver for your particular
card, below.
CONFIG_HISAX_EURO
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
The call control protocol E-DSS1 is used in most European countries.
If unsure, say Y.
CONFIG_DE_AOC
If you want that the HiSax hardware driver sends messages to the
upper level of the isdn code on each AOCD (Advice Of Charge, During
the call -- transmission of the fee information during a call) and
on each AOCE (Advice Of Charge, at the End of the call --
transmission of fee information at the end of the call), say Y here.
This works only in Germany.
CONFIG_HISAX_NO_SENDCOMPLETE
If you have trouble with some ugly exchanges or you live in
Australia select this option.
CONFIG_HISAX_NO_LLC
If you have trouble with some ugly exchanges try to select this
option.
CONFIG_HISAX_NO_KEYPAD
If you like to send special dial strings including * or # without
using the keypad protocol, select this option.
CONFIG_HISAX_1TR6
Say Y or N according to the D-channel protocol which your local
telephone service company provides.
1TR6 is an old call control protocol which was used in Germany
before E-DSS1 was established. Nowadays, all new lines in Germany
use E-DSS1.
CONFIG_HISAX_NI1
Enable this if you like to use ISDN in US on a NI1 basic rate
interface.
CONFIG_HISAX_MAX_CARDS
This option allows you to specify the maximum number of cards which
the HiSax driver will be able to handle.
CONFIG_HISAX_16_0
This enables HiSax support for the Teles ISDN-cards S0-16.0, S0-8
and many compatibles.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port/shmem settings.
CONFIG_HISAX_16_3
This enables HiSax support for the Teles ISDN-cards S0-16.3 the
Teles/Creatix PnP and the Teles PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_TELESPCI
This enables HiSax support for the Teles PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_S0BOX
This enables HiSax support for the Teles/Creatix parallel port
S0BOX. See <file:Documentation/isdn/README.HiSax> on how to
configure it.
CONFIG_HISAX_AVM_A1
This enables HiSax support for the AVM A1 (aka "Fritz").
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_FRITZPCI
This enables HiSax support for the AVM "Fritz!PnP" and "Fritz!PCI".
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_AVM_A1_PCMCIA
This enables HiSax support for the AVM A1 "Fritz!PCMCIA").
See <file:Documentation/isdn/README.HiSax> on how to configure it.
CONFIG_HISAX_ELSA
This enables HiSax support for the Elsa Mircolink ISA cards, for the
Elsa Quickstep series cards and Elsa PCMCIA.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_IX1MICROR2
This enables HiSax support for the ITK ix1-micro Revision 2 card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_DIEHLDIVA
This enables HiSax support for the Eicon.Diehl Diva none PRO
versions passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_ASUSCOM
This enables HiSax support for the AsusCom and their OEM versions
passive ISDN ISA cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_TELEINT
This enables HiSax support for the TELEINT SA1 semiactiv ISDN card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_HFCS
This enables HiSax support for the HFC-S 2BDS0 based cards, like
teles 16.3c.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_SEDLBAUER
This enables HiSax support for the Sedlbauer passive ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using the different cards, a different D-channel protocol, or
non-standard IRQ/port settings.
CONFIG_HISAX_SPORTSTER
This enables HiSax support for the USR Sportster internal TA card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_MIC
This enables HiSax support for the ITH MIC card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NETJET
This enables HiSax support for the NetJet from Traverse
Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NETJET_U
This enables HiSax support for the Netspider U interface ISDN card
from Traverse Technologies.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_NICCY
This enables HiSax support for the Dr. Neuhaus Niccy PnP or PCI.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_ISURF
This enables HiSax support for the Siemens I-Talk/I-Surf card with
ISAR chip.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HSTSAPHIR
This enables HiSax support for the HST Saphir card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_BKM_A4T
This enables HiSax support for the Telekom A4T card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_SCT_QUADRO
This enables HiSax support for the Scitel Quadro card.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_GAZEL
This enables HiSax support for the Gazel cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HFC_PCI
This enables HiSax support for the HFC-S PCI 2BDS0 based cards.
For more informations see under
<file:Documentation/isdn/README.hfc-pci>.
CONFIG_HISAX_W6692
This enables HiSax support for Winbond W6692 based PCI ISDN cards.
See <file:Documentation/isdn/README.HiSax> on how to configure it
using a different D-channel protocol, or non-standard IRQ/port
settings.
CONFIG_HISAX_HFC_SX
This enables HiSax support for the HFC-S+, HFC-SP and HFC-PCMCIA
cards. This code is not finished yet.
CONFIG_HISAX_AMD7930
This enables HiSax support for the AMD7930 chips on some SPARCs.
This code is not finished yet.
CONFIG_HISAX_DEBUG
This enables debugging code in the new-style HiSax drivers, i.e.
the ST5481 USB driver currently.
If in doubt, say yes.
CONFIG_HISAX_ELSA_CS
This enables the PCMCIA client driver for the Elsa PCMCIA MicroLink
card.
CONFIG_HISAX_SEDLBAUER_CS
This enables the PCMCIA client driver for the Sedlbauer Speed Star
and Speed Star II cards.
CONFIG_HISAX_ST5481
This enables the driver for ST5481 based USB ISDN adapters,
e.g. the BeWan Gazel 128 USB
CONFIG_HISAX_FRITZ_PCIPNP
This enables the driver for the AVM Fritz!Card PCI, Fritz!Card PCI v2
and Fritz!Card PnP.
(the latter also needs you to select "ISA Plug and Play support"
from the menu "Plug and Play configuration")
CONFIG_HISAX_FRITZ_CLASSIC
This enables the driver for the AVM Fritz!Card classic, formerly
known as AVM A1.
mainmenu_option next_comment
comment 'Passive ISDN cards'
dep_tristate 'HiSax SiemensChipSet driver support' CONFIG_ISDN_DRV_HISAX $CONFIG_ISDN
if [ "$CONFIG_ISDN_DRV_HISAX" != "n" ]; then
comment ' D-channel protocol features'
bool ' HiSax Support for EURO/DSS1' CONFIG_HISAX_EURO
if [ "$CONFIG_HISAX_EURO" != "n" ]; then
bool ' Support for german chargeinfo' CONFIG_DE_AOC
bool ' Disable sending complete' CONFIG_HISAX_NO_SENDCOMPLETE
bool ' Disable sending low layer compatibility' CONFIG_HISAX_NO_LLC
bool ' Disable keypad protocol option' CONFIG_HISAX_NO_KEYPAD
fi
bool ' HiSax Support for german 1TR6' CONFIG_HISAX_1TR6
bool ' HiSax Support for US NI1' CONFIG_HISAX_NI1
int ' Maximum number of cards supported by HiSax' CONFIG_HISAX_MAX_CARDS 8
comment ' HiSax supported cards'
bool ' Teles 16.0/8.0' CONFIG_HISAX_16_0
bool ' Teles 16.3 or PNP or PCMCIA' CONFIG_HISAX_16_3
bool ' Teles PCI' CONFIG_HISAX_TELESPCI
bool ' Teles S0Box' CONFIG_HISAX_S0BOX
bool ' AVM A1 (Fritz)' CONFIG_HISAX_AVM_A1
bool ' AVM PnP/PCI (Fritz!PnP/PCI)' CONFIG_HISAX_FRITZPCI
bool ' AVM A1 PCMCIA (Fritz)' CONFIG_HISAX_AVM_A1_PCMCIA
bool ' Elsa cards' CONFIG_HISAX_ELSA
bool ' ITK ix1-micro Revision 2' CONFIG_HISAX_IX1MICROR2
bool ' Eicon.Diehl Diva cards' CONFIG_HISAX_DIEHLDIVA
bool ' ASUSCOM ISA cards' CONFIG_HISAX_ASUSCOM
bool ' TELEINT cards' CONFIG_HISAX_TELEINT
bool ' HFC-S based cards' CONFIG_HISAX_HFCS
bool ' Sedlbauer cards' CONFIG_HISAX_SEDLBAUER
bool ' USR Sportster internal TA' CONFIG_HISAX_SPORTSTER
bool ' MIC card' CONFIG_HISAX_MIC
bool ' NETjet card' CONFIG_HISAX_NETJET
bool ' NETspider U card' CONFIG_HISAX_NETJET_U
bool ' Niccy PnP/PCI card' CONFIG_HISAX_NICCY
bool ' Siemens I-Surf card' CONFIG_HISAX_ISURF
bool ' HST Saphir card' CONFIG_HISAX_HSTSAPHIR
bool ' Telekom A4T card' CONFIG_HISAX_BKM_A4T
bool ' Scitel Quadro card' CONFIG_HISAX_SCT_QUADRO
bool ' Gazel cards' CONFIG_HISAX_GAZEL
bool ' HFC PCI-Bus cards' CONFIG_HISAX_HFC_PCI
bool ' Winbond W6692 based cards' CONFIG_HISAX_W6692
bool ' HFC-S+, HFC-SP, HFC-PCMCIA cards' CONFIG_HISAX_HFC_SX
if [ "$CONFIG_EXPERIMENTAL" != "n" ]; then
# bool ' TESTEMULATOR (EXPERIMENTAL)' CONFIG_HISAX_TESTEMU
if [ "$ARCH" = "sparc" -o "$ARCH" = "sparc64" ]; then
bool ' Am7930' CONFIG_HISAX_AMD7930
fi
fi
bool ' HiSax debugging' CONFIG_HISAX_DEBUG
dep_tristate 'Sedlbauer PCMCIA cards' CONFIG_HISAX_SEDLBAUER_CS $CONFIG_PCMCIA
dep_tristate 'ELSA PCMCIA MicroLink cards' CONFIG_HISAX_ELSA_CS $CONFIG_PCMCIA
dep_tristate 'ST5481 USB ISDN modem (EXPERIMENTAL)' CONFIG_HISAX_ST5481 $CONFIG_HISAX $CONFIG_USB $CONFIG_EXPERIMENTAL
dep_tristate 'AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)' CONFIG_HISAX_FRITZ_PCIPNP $CONFIG_HISAX $CONFIG_EXPERIMENTAL
dep_tristate 'AVM Fritz!Card classic support (EXPERIMENTAL)' CONFIG_HISAX_FRITZ_CLASSIC $CONFIG_HISAX $CONFIG_EXPERIMENTAL
dep_tristate 'HFC PCI support (EXPERIMENTAL)' CONFIG_HISAX_HFCPCI $CONFIG_HISAX $CONFIG_EXPERIMENTAL
fi
endmenu
CONFIG_HYSDN
Say Y here if you have one of Hypercope's active PCI ISDN cards
Champ, Ergo and Metro. You will then get a module called hysdn.o.
Please read the file <file:Documentation/isdn/README.hysdn> for more
information.
CONFIG_HYSDN_CAPI
Say Y here if you like to use Hypercope's CAPI 2.0 interface.
#
# Config.in for HYSDN ISDN driver
#
dep_tristate ' Hypercope HYSDN cards (Champ, Ergo, Metro) support (module only)' CONFIG_HYSDN m $CONFIG_PROC_FS
dep_mbool ' HYSDN CAPI 2.0 support' CONFIG_HYSDN_CAPI $CONFIG_HYSDN $CONFIG_ISDN_CAPI
CONFIG_ISDN
This driver allows you to use an ISDN-card for networking
connections and as dialin/out device. The isdn-tty's have a built
in AT-compatible modem emulator. Network devices support autodial,
channel-bundling, callback and caller-authentication without having
a daemon running. A reduced T.70 protocol is supported with tty's
suitable for German BTX. On D-Channel, the protocols EDSS1
(Euro-ISDN) and 1TR6 (German style) are supported. See
<file:Documentation/isdn/README> for more information.
ISDN support in the linux kernel is moving towards a new API,
called CAPI (Common ISDN Application Programming Interface).
Therefore the old ISDN4Linux layer is becoming obsolete. It is
still usable, though, if you select this option.
CONFIG_ISDN_PPP
Over digital connections such as ISDN, there is no need to
synchronize sender and recipient's clocks with start and stop bits
as is done over analog telephone lines. Instead, one can use
"synchronous PPP". Saying Y here will include this protocol. This
protocol is used by Cisco and Sun for example. So you want to say Y
here if the other end of your ISDN connection supports it. You will
need a special version of pppd (called ipppd) for using this
feature. See <file:Documentation/isdn/README.syncppp> and
<file:Documentation/isdn/syncPPP.FAQ> for more information.
CONFIG_ISDN_MPP
With synchronous PPP enabled, it is possible to increase throughput
by bundling several ISDN-connections, using this protocol. See
<file:Documentation/isdn/README.syncppp> for more information.
CONFIG_ISDN_PPP_VJ
This enables Van Jacobson header compression for synchronous PPP.
Say Y if the other end of the connection supports it.
CONFIG_ISDN_PPP_BSDCOMP
Support for the BSD-Compress compression method for PPP, which uses
the LZW compression method to compress each PPP packet before it is
sent over the wire. The machine at the other end of the PPP link
(usually your ISP) has to support the BSD-Compress compression
method as well for this to be useful. Even if they don't support it,
it is safe to say Y here.
CONFIG_ISDN_AUDIO
If you say Y here, the modem-emulator will support a subset of the
EIA Class 8 Voice commands. Using a getty with voice-support
(mgetty+sendfax by gert@greenie.muc.de with an extension, available
with the ISDN utility package for example), you will be able to use
your Linux box as an ISDN-answering machine. Of course, this must be
supported by the lowlevel driver also. Currently, the HiSax driver
is the only voice-supporting driver. See
<file:Documentation/isdn/README.audio> for more information.
CONFIG_ISDN_X25
This feature provides the X.25 protocol over ISDN connections.
See <file:Documentation/isdn/README.x25> for more information
if you are thinking about using this.
CONFIG_ISDN_DIVERSION
This option allows you to use some supplementary diversion
services in conjunction with the HiSax driver on an EURO/DSS1
line.
Supported options are CD (call deflection), CFU (Call forward
unconditional), CFB (Call forward when busy) and CFNR (call forward
not reachable). Additionally the actual CFU, CFB and CFNR state may
be interrogated.
The use of CFU, CFB, CFNR and interrogation may be limited to some
countries. The keypad protocol is still not implemented. CD should
work in all countries if the service has been subscribed to.
Please read the file <file:Documentation/isdn/README.diversion>.
CONFIG_ISDN_TTY_FAX
If you say Y here, the modem-emulator will support a subset of the
Fax Class 1 and 2 commands. Using a getty with fax-support
(mgetty+sendfax, hylafax), you will be able to use your Linux box as
an ISDN-fax-machine. This must be supported by the lowlevel driver
also. See <file:Documentation/isdn/README.fax> for more information.
CONFIG_ISDN_DRV_LOOP
This driver provides a virtual ISDN card. Its primary purpose is
testing of linklevel features or configuration without getting
charged by your service-provider for lots of phone calls.
You need will need the loopctrl utility from the latest isdn4k-utils
package to set up this driver.
......@@ -26,128 +26,21 @@ endmenu
comment 'low-level hardware drivers'
mainmenu_option next_comment
comment 'Passive ISDN cards'
dep_tristate 'HiSax SiemensChipSet driver support' CONFIG_ISDN_DRV_HISAX $CONFIG_ISDN
if [ "$CONFIG_ISDN_DRV_HISAX" != "n" ]; then
comment ' D-channel protocol features'
bool ' HiSax Support for EURO/DSS1' CONFIG_HISAX_EURO
if [ "$CONFIG_HISAX_EURO" != "n" ]; then
bool ' Support for german chargeinfo' CONFIG_DE_AOC
bool ' Disable sending complete' CONFIG_HISAX_NO_SENDCOMPLETE
bool ' Disable sending low layer compatibility' CONFIG_HISAX_NO_LLC
bool ' Disable keypad protocol option' CONFIG_HISAX_NO_KEYPAD
fi
bool ' HiSax Support for german 1TR6' CONFIG_HISAX_1TR6
bool ' HiSax Support for US NI1' CONFIG_HISAX_NI1
int ' Maximum number of cards supported by HiSax' CONFIG_HISAX_MAX_CARDS 8
comment ' HiSax supported cards'
bool ' Teles 16.0/8.0' CONFIG_HISAX_16_0
bool ' Teles 16.3 or PNP or PCMCIA' CONFIG_HISAX_16_3
bool ' Teles PCI' CONFIG_HISAX_TELESPCI
bool ' Teles S0Box' CONFIG_HISAX_S0BOX
bool ' AVM A1 (Fritz)' CONFIG_HISAX_AVM_A1
bool ' AVM PnP/PCI (Fritz!PnP/PCI)' CONFIG_HISAX_FRITZPCI
bool ' AVM A1 PCMCIA (Fritz)' CONFIG_HISAX_AVM_A1_PCMCIA
bool ' Elsa cards' CONFIG_HISAX_ELSA
bool ' ITK ix1-micro Revision 2' CONFIG_HISAX_IX1MICROR2
bool ' Eicon.Diehl Diva cards' CONFIG_HISAX_DIEHLDIVA
bool ' ASUSCOM ISA cards' CONFIG_HISAX_ASUSCOM
bool ' TELEINT cards' CONFIG_HISAX_TELEINT
bool ' HFC-S based cards' CONFIG_HISAX_HFCS
bool ' Sedlbauer cards' CONFIG_HISAX_SEDLBAUER
bool ' USR Sportster internal TA' CONFIG_HISAX_SPORTSTER
bool ' MIC card' CONFIG_HISAX_MIC
bool ' NETjet card' CONFIG_HISAX_NETJET
bool ' NETspider U card' CONFIG_HISAX_NETJET_U
bool ' Niccy PnP/PCI card' CONFIG_HISAX_NICCY
bool ' Siemens I-Surf card' CONFIG_HISAX_ISURF
bool ' HST Saphir card' CONFIG_HISAX_HSTSAPHIR
bool ' Telekom A4T card' CONFIG_HISAX_BKM_A4T
bool ' Scitel Quadro card' CONFIG_HISAX_SCT_QUADRO
bool ' Gazel cards' CONFIG_HISAX_GAZEL
bool ' HFC PCI-Bus cards' CONFIG_HISAX_HFC_PCI
bool ' Winbond W6692 based cards' CONFIG_HISAX_W6692
bool ' HFC-S+, HFC-SP, HFC-PCMCIA cards' CONFIG_HISAX_HFC_SX
if [ "$CONFIG_EXPERIMENTAL" != "n" ]; then
# bool ' TESTEMULATOR (EXPERIMENTAL)' CONFIG_HISAX_TESTEMU
if [ "$ARCH" = "sparc" -o "$ARCH" = "sparc64" ]; then
bool ' Am7930' CONFIG_HISAX_AMD7930
fi
fi
bool ' HiSax debugging' CONFIG_HISAX_DEBUG
dep_tristate 'Sedlbauer PCMCIA cards' CONFIG_HISAX_SEDLBAUER_CS $CONFIG_PCMCIA
dep_tristate 'ELSA PCMCIA MicroLink cards' CONFIG_HISAX_ELSA_CS $CONFIG_PCMCIA
dep_tristate 'ST5481 USB ISDN modem (EXPERIMENTAL)' CONFIG_HISAX_ST5481 $CONFIG_HISAX $CONFIG_USB $CONFIG_EXPERIMENTAL
dep_tristate 'AVM Fritz!Card PCI/PCIv2/PnP support (EXPERIMENTAL)' CONFIG_HISAX_FRITZ_PCIPNP $CONFIG_HISAX $CONFIG_EXPERIMENTAL
dep_tristate 'AVM Fritz!Card classic support (EXPERIMENTAL)' CONFIG_HISAX_FRITZ_CLASSIC $CONFIG_HISAX $CONFIG_EXPERIMENTAL
dep_tristate 'HFC PCI support (EXPERIMENTAL)' CONFIG_HISAX_HFCPCI $CONFIG_HISAX $CONFIG_EXPERIMENTAL
fi
endmenu
source drivers/isdn/hisax/Config.in
### Active ISDN cards
mainmenu_option next_comment
comment 'Active ISDN cards'
dep_tristate 'ICN 2B and 4B support' CONFIG_ISDN_DRV_ICN $CONFIG_ISDN
dep_tristate 'PCBIT-D support' CONFIG_ISDN_DRV_PCBIT $CONFIG_ISDN
dep_tristate 'Spellcaster support' CONFIG_ISDN_DRV_SC $CONFIG_ISDN
dep_tristate 'IBM Active 2000 support' CONFIG_ISDN_DRV_ACT2000 $CONFIG_ISDN
bool 'Eicon active card support' CONFIG_ISDN_DRV_EICON
if [ "$CONFIG_ISDN_DRV_EICON" != "n" ]; then
if [ "$CONFIG_ISDN_DRV_EICON_OLD" != "y" ]; then
dep_tristate ' Build Eicon driver type standalone' CONFIG_ISDN_DRV_EICON_DIVAS $CONFIG_ISDN $CONFIG_PCI
fi
if [ "$CONFIG_ISDN_DRV_EICON_DIVAS" != "y" ]; then
dep_tristate ' Legacy Eicon driver' CONFIG_ISDN_DRV_EICON_OLD $CONFIG_ISDN
if [ "$CONFIG_ISDN_DRV_EICON_OLD" != "n" ]; then
dep_bool ' Eicon PCI DIVA Server BRI/PRI/4BRI support' CONFIG_ISDN_DRV_EICON_PCI $CONFIG_PCI
bool ' Eicon S,SX,SCOM,Quadro,S2M support' CONFIG_ISDN_DRV_EICON_ISA
fi
fi
fi
if [ "$CONFIG_EXPERIMENTAL" != "n" ]; then
dep_tristate 'Auvertech TurboPAM support' CONFIG_ISDN_DRV_TPAM $CONFIG_ISDN $CONFIG_PCI
fi
# CAPI subsystem
tristate 'CAPI2.0 support' CONFIG_ISDN_CAPI
if [ "$CONFIG_ISDN_CAPI" != "n" ]; then
bool ' Verbose reason code reporting (kernel size +=7K)' CONFIG_ISDN_DRV_AVMB1_VERBOSE_REASON
dep_bool ' CAPI2.0 Middleware support (EXPERIMENTAL)' CONFIG_ISDN_CAPI_MIDDLEWARE $CONFIG_EXPERIMENTAL
dep_tristate ' CAPI2.0 /dev/capi support' CONFIG_ISDN_CAPI_CAPI20 $CONFIG_ISDN_CAPI
if [ "$CONFIG_ISDN_CAPI_MIDDLEWARE" = "y" ]; then
dep_mbool ' CAPI2.0 filesystem support' CONFIG_ISDN_CAPI_CAPIFS_BOOL $CONFIG_ISDN_CAPI_CAPI20
if [ "$CONFIG_ISDN_CAPI_CAPIFS_BOOL" = "y" ]; then
define_tristate CONFIG_ISDN_CAPI_CAPIFS $CONFIG_ISDN_CAPI_CAPI20
else
define_tristate CONFIG_ISDN_CAPI_CAPIFS n
fi
fi
dep_tristate ' CAPI2.0 capidrv interface support' CONFIG_ISDN_CAPI_CAPIDRV $CONFIG_ISDN_CAPI $CONFIG_ISDN
fi
# CAPI drivers
if [ "$CONFIG_ISDN_CAPI" != "n" ]; then
dep_tristate ' AVM B1 ISA support' CONFIG_ISDN_DRV_AVMB1_B1ISA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1 PCI support' CONFIG_ISDN_DRV_AVMB1_B1PCI $CONFIG_ISDN_CAPI $CONFIG_PCI
dep_mbool ' AVM B1 PCI V4 support' CONFIG_ISDN_DRV_AVMB1_B1PCIV4 $CONFIG_ISDN_DRV_AVMB1_B1PCI
dep_tristate ' AVM T1/T1-B ISA support' CONFIG_ISDN_DRV_AVMB1_T1ISA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1/M1/M2 PCMCIA support' CONFIG_ISDN_DRV_AVMB1_B1PCMCIA $CONFIG_ISDN_CAPI
dep_tristate ' AVM B1/M1/M2 PCMCIA cs module' CONFIG_ISDN_DRV_AVMB1_AVM_CS $CONFIG_ISDN_DRV_AVMB1_B1PCMCIA $CONFIG_PCMCIA
dep_tristate ' AVM T1/T1-B PCI support' CONFIG_ISDN_DRV_AVMB1_T1PCI $CONFIG_ISDN_CAPI $CONFIG_PCI
dep_tristate ' AVM C4/C2 support' CONFIG_ISDN_DRV_AVMB1_C4 $CONFIG_ISDN_CAPI $CONFIG_PCI
fi
# HYSDN
source drivers/isdn/icn/Config.in
source drivers/isdn/pcbit/Config.in
source drivers/isdn/sc/Config.in
source drivers/isdn/act2000/Config.in
source drivers/isdn/eicon/Config.in
source drivers/isdn/tpam/Config.in
source drivers/isdn/avmb1/Config.in
source drivers/isdn/hysdn/Config.in
dep_tristate ' Hypercope HYSDN cards (Champ, Ergo, Metro) support (module only)' CONFIG_HYSDN m $CONFIG_PROC_FS
dep_mbool ' HYSDN CAPI 2.0 support' CONFIG_HYSDN_CAPI $CONFIG_HYSDN $CONFIG_ISDN_CAPI
endmenu
CONFIG_ISDN_DRV_ICN
This enables support for two kinds of ISDN-cards made by a German
company called ICN. 2B is the standard version for a single ISDN
line with two B-channels, 4B supports two ISDN lines. For running
this card, additional firmware is necessary, which has to be
downloaded into the card using a utility which is distributed
separately. See <file:Documentation/isdn/README> and
<file:Documentation/isdn/README.icn> for more
information.
#
# Config.in for ICN ISDN driver
#
dep_tristate 'ICN 2B and 4B support' CONFIG_ISDN_DRV_ICN $CONFIG_ISDN
CONFIG_ISDN_DRV_PCBIT
This enables support for the PCBIT ISDN-card. This card is
manufactured in Portugal by Octal. For running this card,
additional firmware is necessary, which has to be downloaded into
the card using a utility which is distributed separately. See
<file:Documentation/isdn/README> and
<file:Documentation/isdn/README.pcbit> for more information.
#
# Config.in for PCBIT ISDN driver
#
dep_tristate 'PCBIT-D support' CONFIG_ISDN_DRV_PCBIT $CONFIG_ISDN
CONFIG_ISDN_DRV_SC
This enables support for the Spellcaster BRI ISDN boards. This
driver currently builds only in a modularized version ( = code which
can be inserted in and removed from the running kernel whenever you
want, details in <file:Documentation/modules.txt>); the module will
be called sc.o. See <file:Documentation/isdn/README.sc> and
<http://www.spellcast.com/> for more information.
#
# Config.in for Spellcaster ISDN driver
#
dep_tristate 'Spellcaster support' CONFIG_ISDN_DRV_SC $CONFIG_ISDN
CONFIG_ISDN_DRV_TPAM
This enables support for the Auvertech TurboPAM ISDN-card.
For running this card, additional firmware is necessary, which has
to be downloaded into the card using a utility which is distributed
separately from the Auvertech's web site: <http://www.auvertech.fr/>.
Please redirect all support questions to support@auvertech.fr.
#
# Config.in for Auvertech TurboPAM ISDN driver
#
if [ "$CONFIG_EXPERIMENTAL" != "n" ]; then
dep_tristate 'Auvertech TurboPAM support' CONFIG_ISDN_DRV_TPAM $CONFIG_ISDN $CONFIG_PCI
fi
Markdown is supported
0%
or
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment