ARM: add an extra temp register to the low level debugging addruart macro

Some platforms (like OMAP not to name it) are doing rather complicated
hacks just to determine the base UART address to use.  Let's give their
addruart macro some slack by providing an extra work register which will
allow for much needed cleanups.

This is basically a no-op as this commit is only adding the extra argument
to the macro but no one is using it yet.
Signed-off-by: nicolas Pitre <nicolas.pitre@linaro.org>
Reviewed-by: Kevin Hilman <khilman@ti.com>

arch/arm/kernel/debug.S

@@ -22,7 +22,7 @@
 #if defined(CONFIG_DEBUG_ICEDCC)
 		@@ debug using ARM EmbeddedICE DCC channel
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.endm
 
 #if defined(CONFIG_CPU_V6) || defined(CONFIG_CPU_V6K) || defined(CONFIG_CPU_V7)
@@ -106,7 +106,7 @@
 
 #ifdef CONFIG_MMU
 		.macro	addruart_current, rx, tmp1, tmp2
-		addruart	\tmp1, \tmp2
+		addruart	\tmp1, \tmp2, \rx
 		mrc		p15, 0, \rx, c1, c0
 		tst		\rx, #1
 		moveq		\rx, \tmp1

arch/arm/kernel/head.S

@@ -234,7 +234,7 @@ __create_page_tables:
 	 * This allows debug messages to be output
 	 * via a serial console before paging_init.
 	 */
-	addruart r7, r3
+	addruart r7, r3, r0
 
 	mov	r3, r3, lsr #20
 	mov	r3, r3, lsl #2

arch/arm/mach-at91/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/at91_dbgu.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =(AT91_BASE_SYS + AT91_DBGU)	@ System peripherals (phys address)
 	ldr	\rv, =(AT91_VA_BASE_SYS	+ AT91_DBGU)	@ System peripherals (virt address)
 	.endm

arch/arm/mach-clps711x/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <asm/hardware/clps7111.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 #ifndef CONFIG_DEBUG_CLPS711X_UART2
 		mov	\rp, #0x0000	@ UART1
 #else

arch/arm/mach-cns3xxx/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart,rp,rv
+		.macro	addruart,rp,rv,tmp
 		mov	\rp, #0x00009000
 		orr	\rv, \rp, #0xf0000000	@ virtual base
 		orr	\rp, \rp, #0x10000000

arch/arm/mach-davinci/include/mach/debug-macro.S

@@ -32,7 +32,7 @@ davinci_uart_phys:	.word	0
 davinci_uart_virt:	.word	0
 		.popsection
 
-		.macro addruart, rp, rv
+		.macro addruart, rp, rv, tmp
 
 		/* Use davinci_uart_phys/virt if already configured */
 10:		mrc	p15, 0, \rp, c1, c0

arch/arm/mach-dove/include/mach/debug-macro.S

@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =DOVE_SB_REGS_PHYS_BASE
 	ldr	\rv, =DOVE_SB_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000

arch/arm/mach-ebsa110/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 **/
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xf0000000
 		orr	\rp, \rp, #0x00000be0
 		mov	\rp, \rv

arch/arm/mach-ep93xx/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/ep93xx-regs.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =EP93XX_APB_PHYS_BASE	@ Physical base
 		ldr	\rv, =EP93XX_APB_VIRT_BASE	@ virtual base
 		orr	\rp, \rp, #0x000c0000

arch/arm/mach-exynos4/include/mach/debug-macro.S

@@ -20,7 +20,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-footbridge/include/mach/debug-macro.S

@@ -15,7 +15,7 @@
 
 #ifndef CONFIG_DEBUG_DC21285_PORT
 	/* For NetWinder debugging */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x000003f8
 		orr	\rv, \rp, #0xff000000	@ virtual
 		orr	\rp, \rp, #0x7c000000	@ physical
@@ -31,7 +31,7 @@
 		.equ	dc21285_high, ARMCSR_BASE & 0xff000000
 		.equ	dc21285_low,  ARMCSR_BASE & 0x00ffffff
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		.if	dc21285_low
 		mov	\rp, #dc21285_low
 		.else

arch/arm/mach-gemini/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =GEMINI_UART_BASE			@ physical
 	ldr	\rv, =IO_ADDRESS(GEMINI_UART_BASE)	@ virtual
 	.endm

arch/arm/mach-h720x/include/mach/debug-macro.S

@@ -16,7 +16,7 @@
 		.equ    io_virt, IO_VIRT
 		.equ    io_phys, IO_PHYS
 
-		.macro  addruart, rp, rv
+		.macro  addruart, rp, rv, tmp
 		mov     \rp, #0x00020000	@ UART1
 		add     \rv, \rp, #io_virt	@ virtual address
 		add     \rp, \rp, #io_phys	@ physical base address

arch/arm/mach-integrator/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x16000000	@ physical base address
 		mov	\rv, #0xf0000000	@ virtual base
 		add	\rv, \rv, #0x16000000 >> 4

arch/arm/mach-iop13xx/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	mov	\rp, #0x00002300
 	orr	\rp, \rp, #0x00000040
 	orr	\rv, \rp, #0xfe000000	@ virtual

arch/arm/mach-iop32x/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xfe000000	@ physical as well as virtual
 		orr	\rp, \rp, #0x00800000	@ location of the UART
 		mov	\rv, \rp

arch/arm/mach-iop33x/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  * published by the Free Software Foundation.
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00ff0000
 		orr	\rp, \rp, #0x0000f700
 		orr	\rv, #0xfe000000	@ virtual

arch/arm/mach-ixp2000/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro  addruart, rp, rv
+		.macro  addruart, rp, rv, tmp
 		mov	\rp, #0x00030000
 #ifdef	__ARMEB__
 		orr	\rp, \rp, #0x00000003

arch/arm/mach-ixp23xx/include/mach/debug-macro.S

@@ -12,7 +12,7 @@
  */
 #include <mach/ixp23xx.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =IXP23XX_PERIPHERAL_PHYS 	@ physical
 		ldr	\rv, =IXP23XX_PERIPHERAL_VIRT	@ virtual
 #ifdef __ARMEB__

arch/arm/mach-ixp4xx/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  * published by the Free Software Foundation.
 */
 
-                .macro  addruart, rp, rv
+                .macro  addruart, rp, rv, tmp
 #ifdef __ARMEB__
                 mov     \rp, #3         @ Uart regs are at off set of 3 if
 					@ byte writes used - Big Endian.

arch/arm/mach-kirkwood/include/mach/debug-macro.S

@@ -8,7 +8,7 @@
 
 #include <mach/bridge-regs.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =KIRKWOOD_REGS_PHYS_BASE
 	ldr	\rv, =KIRKWOOD_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000

arch/arm/mach-ks8695/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 #include <mach/hardware.h>
 #include <mach/regs-uart.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 		ldr	\rp, =KS8695_UART_PA		@ physical base address
 		ldr	\rv, =KS8695_UART_VA		@ virtual base address
 	.endm

arch/arm/mach-l7200/include/mach/debug-macro.S

@@ -14,7 +14,7 @@
 		.equ	io_virt, IO_BASE
 		.equ	io_phys, IO_START
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00044000	@ UART1
 @		mov	\rp, #0x00045000	@ UART2
 		add	\rv, \rp, #io_virt	@ virtual address

arch/arm/mach-lpc32xx/include/mach/debug-macro.S

@@ -20,7 +20,7 @@
  * Debug output is hardcoded to standard UART 5
 */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldreq	\rp, =0x40090000
 	ldrne	\rv, =0xF4090000
 	.endm

arch/arm/mach-mmp/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
 
 #include <mach/addr-map.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =APB_PHYS_BASE		@ physical
 		ldr	\rv, =APB_VIRT_BASE		@ virtual
 		orr	\rp, \rp, #0x00017000

arch/arm/mach-msm/include/mach/debug-macro.S

@@ -20,7 +20,7 @@
 #include <mach/msm_iomap.h>
 
 #if defined(CONFIG_HAS_MSM_DEBUG_UART_PHYS) && !defined(CONFIG_MSM_DEBUG_UART_NONE)
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =MSM_DEBUG_UART_PHYS
 	ldr	\rv, =MSM_DEBUG_UART_BASE
 	.endm
@@ -37,7 +37,7 @@
 	beq	1001b
 	.endm
 #else
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
 	mov	\rv, #0xff000000
 	orr	\rv, \rv, #0x00f00000
 	.endm

arch/arm/mach-mv78xx0/include/mach/debug-macro.S

@@ -8,7 +8,7 @@
 
 #include <mach/mv78xx0.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =MV78XX0_REGS_PHYS_BASE
 	ldr	\rv, =MV78XX0_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000

arch/arm/mach-mxs/include/mach/debug-macro.S

@@ -30,7 +30,7 @@
 
 #define UART_VADDR	MXS_IO_ADDRESS(UART_PADDR)
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =UART_PADDR	@ physical
 		ldr	\rv, =UART_VADDR	@ virtual
 		.endm

arch/arm/mach-netx/include/mach/debug-macro.S

@@ -13,7 +13,7 @@
 
 #include "hardware.h"
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00000a00
 		orr	\rv, \rp, #io_p2v(0x00100000)	@ virtual
 		orr	\rp, \rp, #0x00100000		@ physical

arch/arm/mach-nomadik/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00100000
 		add	\rp, \rp, #0x000fb000
 		add	\rv, \rp, #0xf0000000	@ virtual base

arch/arm/mach-omap1/include/mach/debug-macro.S

@@ -31,7 +31,7 @@ omap_uart_virt:	.word	0x0
 		 * the desired UART phys and virt addresses temporarily into
 		 * the omap_uart_phys and omap_uart_virt above.
 		 */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 
 		/* Use omap_uart_phys/virt if already configured */
 9:		mrc	p15, 0, \rp, c1, c0

arch/arm/mach-omap2/include/mach/debug-macro.S

@@ -34,7 +34,7 @@ omap_uart_lsr:	.word	0
 		 * the desired UART phys and virt addresses temporarily into
 		 * the omap_uart_phys and omap_uart_virt above.
 		 */
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 
 		/* Use omap_uart_phys/virt if already configured */
 10:		mrc	p15, 0, \rp, c1, c0

arch/arm/mach-orion5x/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
 
 #include <mach/orion5x.h>
 
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
 	ldr	\rp, =ORION5X_REGS_PHYS_BASE
 	ldr	\rv, =ORION5X_REGS_VIRT_BASE
 	orr	\rp, \rp, #0x00012000

arch/arm/mach-pnx4008/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00090000
 		add	\rv, \rp, #0xf4000000	@ virtual
 		add	\rp, \rp, #0x40000000	@ physical

arch/arm/mach-prima2/include/mach/debug-macro.S

@@ -9,7 +9,7 @@
 #include <mach/hardware.h>
 #include <mach/uart.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =SIRFSOC_UART1_PA_BASE		@ physical
 	ldr	\rv, =SIRFSOC_UART1_VA_BASE		@ virtual
 	.endm

arch/arm/mach-pxa/include/mach/debug-macro.S

@@ -13,7 +13,7 @@
 
 #include "hardware.h"
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00100000
 		orr	\rv, \rp, #io_p2v(0x40000000)	@ virtual
 		orr	\rp, \rp, #0x40000000		@ physical

arch/arm/mach-realview/include/mach/debug-macro.S

@@ -33,7 +33,7 @@
 #error "Unknown RealView platform"
 #endif
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #DEBUG_LL_UART_OFFSET
 		orr	\rv, \rp, #0xfb000000	@ virtual base
 		orr	\rp, \rp, #0x10000000	@ physical base

arch/arm/mach-rpc/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0x00010000
 		orr	\rp, \rp, #0x00000fe0
 		orr	\rv, \rp, #0xe0000000	@ virtual

arch/arm/mach-s3c2410/include/mach/debug-macro.S

@@ -19,7 +19,7 @@
 #define S3C2410_UART1_OFF (0x4000)
 #define SHIFT_2440TXF (14-9)
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C24XX_PA_UART
 		ldr	\rv, = S3C24XX_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-s3c64xx/include/mach/debug-macro.S

@@ -21,7 +21,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = (S3C_VA_UART + S3C_PA_UART & 0xfffff)
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-s5p64x0/include/mach/debug-macro.S

@@ -15,7 +15,7 @@
 
 #include <plat/regs-serial.h>
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		mov	\rp, #0xE0000000
 		orr	\rp, \rp, #0x00100000
 		ldr	\rp, [\rp, #0x118 ]

arch/arm/mach-s5pc100/include/mach/debug-macro.S

@@ -22,7 +22,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-s5pv210/include/mach/debug-macro.S

@@ -21,7 +21,7 @@
 	 * aligned and add in the offset when we load the value here.
 	 */
 
-	.macro addruart, rp, rv
+	.macro addruart, rp, rv, tmp
 		ldr	\rp, = S3C_PA_UART
 		ldr	\rv, = S3C_VA_UART
 #if CONFIG_DEBUG_S3C_UART != 0

arch/arm/mach-sa1100/include/mach/debug-macro.S

@@ -12,7 +12,7 @@
 */
 #include <mach/hardware.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mrc	p15, 0, \rp, c1, c0
 		tst	\rp, #1			@ MMU enabled?
 		moveq	\rp, #0x80000000	@ physical base address

arch/arm/mach-shark/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #0xe0000000
 		orr	\rp, \rp, #0x000003f8
 		mov	\rv, \rp

arch/arm/mach-tegra/include/mach/debug-macro.S

@@ -21,7 +21,7 @@
 #include <mach/io.h>
 #include <mach/iomap.h>
 
-	.macro  addruart, rp, rv
+	.macro  addruart, rp, rv, tmp
         ldr     \rp, =IO_APB_PHYS       @ physical
         ldr     \rv, =IO_APB_VIRT        @ virtual
 	orr	\rp, \rp, #(TEGRA_DEBUG_UART_BASE & 0xFF)

arch/arm/mach-u300/include/mach/debug-macro.S

@@ -10,7 +10,7 @@
  */
 #include <mach/hardware.h>
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	/* If we move the address using MMU, use this. */
 	ldr	\rp,	  = U300_SLOW_PER_PHYS_BASE @ MMU off, physical address
 	ldr	\rv,	  = U300_SLOW_PER_VIRT_BASE @ MMU on, virtual address

arch/arm/mach-ux500/include/mach/debug-macro.S

@@ -35,7 +35,7 @@
 #define UX500_UART(n)	__UX500_UART(n)
 #define UART_BASE	UX500_UART(CONFIG_UX500_DEBUG_UART)
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	ldr	\rp, =UART_BASE				@ no, physical address
 	ldr	\rv, =IO_ADDRESS(UART_BASE)		@ yes, virtual address
 	.endm

arch/arm/mach-versatile/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp,      #0x001F0000
 		orr	\rp, \rp, #0x00001000
 		orr	\rv, \rp, #0xf1000000	@ virtual base

arch/arm/mach-vexpress/include/mach/debug-macro.S

@@ -12,7 +12,7 @@
 
 #define DEBUG_LL_UART_OFFSET	0x00009000
 
-		.macro	addruart,rp,rv
+		.macro	addruart,rp,rv,tmp
 		mov	\rp, #DEBUG_LL_UART_OFFSET
 		orr	\rv, \rp, #0xf8000000	@ virtual base
 		orr	\rp, \rp, #0x10000000	@ physical base

arch/arm/mach-vt8500/include/mach/debug-macro.S

@@ -11,7 +11,7 @@
  *
 */
 
-	.macro	addruart, rp, rv
+	.macro	addruart, rp, rv, tmp
 	mov	\rp,      #0x00200000
 	orr	\rv, \rp, #0xf8000000
 	orr	\rp, \rp, #0xd8000000

arch/arm/mach-zynq/include/mach/debug-macro.S

@@ -17,7 +17,7 @@
 #include <mach/zynq_soc.h>
 #include <mach/uart.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =LL_UART_PADDR	@ physical
 		ldr	\rv, =LL_UART_VADDR	@ virtual
 		.endm

arch/arm/plat-mxc/include/mach/debug-macro.S

@@ -54,7 +54,7 @@
 
 #define UART_VADDR	IMX_IO_ADDRESS(UART_PADDR)
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		ldr	\rp, =UART_PADDR	@ physical
 		ldr	\rv, =UART_VADDR	@ virtual
 		.endm

arch/arm/plat-spear/include/plat/debug-macro.S

@@ -14,7 +14,7 @@
 #include <linux/amba/serial.h>
 #include <mach/hardware.h>
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		mov	\rp, #SPEAR_DBG_UART_BASE		@ Physical base
 		mov	\rv, #VA_SPEAR_DBG_UART_BASE		@ Virtual base
 		.endm

arch/arm/plat-tcc/include/mach/debug-macro.S

@@ -9,7 +9,7 @@
  *
  */
 
-		.macro	addruart, rp, rv
+		.macro	addruart, rp, rv, tmp
 		moveq	\rp, #0x90000000	@ physical base address
 		movne	\rv, #0xF1000000	@ virtual base
 		orr	\rp, \rp, #0x00007000	@ UART0