ARM: at91/boards: use -EINVAL for invalid gpio

this will allow to use gpio_is_valid
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>

arch/arm/mach-at91/board-1arm.c

@@ -70,6 +70,8 @@ static struct macb_platform_data __initdata onearm_eth_data = {
 
 static struct at91_usbh_data __initdata onearm_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata onearm_udc_data = {

arch/arm/mach-at91/board-afeb-9260v1.c

@@ -75,6 +75,8 @@ static void __init afeb9260_init_early(void)
  */
 static struct at91_usbh_data __initdata afeb9260_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata afeb9260_usbh_data = {
  */
 static struct at91_udc_data __initdata afeb9260_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -138,6 +140,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = {
 	.bus_width_16	= 0,
 	.parts		= afeb9260_nand_partition,
 	.num_parts	= ARRAY_SIZE(afeb9260_nand_partition),
+	.det_pin	= -EINVAL,
 };
 
 
@@ -149,6 +152,7 @@ static struct at91_mmc_data __initdata afeb9260_mmc_data = {
 	.wp_pin 	= AT91_PIN_PC4,
 	.slot_b		= 1,
 	.wire4		= 1,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -169,6 +173,8 @@ static struct i2c_board_info __initdata afeb9260_i2c_devices[] = {
 static struct at91_cf_data afeb9260_cf_data = {
 	.chipselect = 4,
 	.irq_pin    = AT91_PIN_PA6,
+	.det_pin	= -EINVAL,
+	.vcc_pin	= -EINVAL,
 	.rst_pin    = AT91_PIN_PA7,
 	.flags      = AT91_CF_TRUE_IDE,
 };

arch/arm/mach-at91/board-cam60.c

@@ -62,6 +62,8 @@ static void __init cam60_init_early(void)
  */
 static struct at91_usbh_data __initdata cam60_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -135,7 +137,7 @@ static struct mtd_partition __initdata cam60_nand_partition[] = {
 static struct atmel_nand_data __initdata cam60_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA9,
 	.enable_pin	= AT91_PIN_PA7,
 	.parts		= cam60_nand_partition,

arch/arm/mach-at91/board-cap9adk.c

@@ -70,6 +70,8 @@ static void __init cap9adk_init_early(void)
  */
 static struct at91_usbh_data __initdata cap9adk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -144,9 +146,9 @@ static struct spi_board_info cap9adk_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata cap9adk_mmc_data = {
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -154,6 +156,7 @@ static struct at91_mmc_data __initdata cap9adk_mmc_data = {
  * MACB Ethernet device
  */
 static struct macb_platform_data __initdata cap9adk_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -172,8 +175,8 @@ static struct mtd_partition __initdata cap9adk_nand_partitions[] = {
 static struct atmel_nand_data __initdata cap9adk_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
-//	.rdy_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.rdy_pin	= -EINVAL,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= cap9adk_nand_partitions,
 	.num_parts	= ARRAY_SIZE(cap9adk_nand_partitions),
@@ -351,7 +354,7 @@ static struct atmel_lcdfb_info __initdata cap9adk_lcdc_data;
  * AC97
  */
 static struct ac97c_platform_data cap9adk_ac97_data = {
-//	.reset_pin	= ... not connected
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-carmeva.c

@@ -64,6 +64,8 @@ static struct macb_platform_data __initdata carmeva_eth_data = {
 
 static struct at91_usbh_data __initdata carmeva_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata carmeva_udc_data = {
@@ -75,8 +77,8 @@ static struct at91_udc_data __initdata carmeva_udc_data = {
 // static struct at91_cf_data __initdata carmeva_cf_data = {
 //	.det_pin	= AT91_PIN_PB0,
 //	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
+	// .irq_pin	= -EINVAL,
+	// .vcc_pin	= -EINVAL,
 // };
 
 static struct at91_mmc_data __initdata carmeva_mmc_data = {
@@ -84,6 +86,7 @@ static struct at91_mmc_data __initdata carmeva_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PB10,
 	.wp_pin		= AT91_PIN_PC14,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info carmeva_spi_devices[] = {

arch/arm/mach-at91/board-cpu9krea.c

@@ -86,6 +86,8 @@ static void __init cpu9krea_init_early(void)
  */
 static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,13 +95,14 @@ static struct at91_usbh_data __initdata cpu9krea_usbh_data = {
  */
 static struct at91_udc_data __initdata cpu9krea_udc_data = {
 	.vbus_pin	= AT91_PIN_PC8,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
  * MACB Ethernet device
  */
 static struct macb_platform_data __initdata cpu9krea_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -112,6 +115,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 #ifdef CONFIG_MACH_CPU9260
@@ -337,6 +341,8 @@ static struct at91_mmc_data __initdata cpu9krea_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA29,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init cpu9krea_board_init(void)

arch/arm/mach-at91/board-cpuat91.c

@@ -83,11 +83,14 @@ static void __init cpuat91_init_early(void)
 }
 
 static struct macb_platform_data __initdata cpuat91_eth_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
 static struct at91_usbh_data __initdata cpuat91_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata cpuat91_udc_data = {
@@ -98,6 +101,8 @@ static struct at91_udc_data __initdata cpuat91_udc_data = {
 static struct at91_mmc_data __initdata cpuat91_mmc_data = {
 	.det_pin	= AT91_PIN_PC2,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data cpuat91_flash_data = {

arch/arm/mach-at91/board-csb337.c

@@ -65,11 +65,13 @@ static struct macb_platform_data __initdata csb337_eth_data = {
 
 static struct at91_usbh_data __initdata csb337_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb337_udc_data = {
-	// this has no VBUS sensing pin
 	.pullup_pin	= AT91_PIN_PA24,
+	.vbus_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata csb337_i2c_devices[] = {
@@ -98,6 +100,7 @@ static struct at91_mmc_data __initdata csb337_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PD6,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct spi_board_info csb337_spi_devices[] = {

arch/arm/mach-at91/board-csb637.c

@@ -59,6 +59,8 @@ static struct macb_platform_data __initdata csb637_eth_data = {
 
 static struct at91_usbh_data __initdata csb637_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata csb637_udc_data = {

arch/arm/mach-at91/board-dt.c

@@ -50,6 +50,7 @@ static void __init ek_init_early(void)
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
 };

arch/arm/mach-at91/board-eb9200.c

@@ -67,6 +67,8 @@ static struct macb_platform_data __initdata eb9200_eth_data = {
 
 static struct at91_usbh_data __initdata eb9200_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eb9200_udc_data = {
@@ -75,15 +77,18 @@ static struct at91_udc_data __initdata eb9200_udc_data = {
 };
 
 static struct at91_cf_data __initdata eb9200_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 static struct at91_mmc_data __initdata eb9200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct i2c_board_info __initdata eb9200_i2c_devices[] = {

arch/arm/mach-at91/board-ecbat91.c

@@ -71,11 +71,16 @@ static struct macb_platform_data __initdata ecb_at91eth_data = {
 
 static struct at91_usbh_data __initdata ecb_at91usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata ecb_at91mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-eco920.c

@@ -54,6 +54,8 @@ static struct macb_platform_data __initdata eco920_eth_data = {
 
 static struct at91_usbh_data __initdata eco920_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata eco920_udc_data = {
@@ -64,6 +66,9 @@ static struct at91_udc_data __initdata eco920_udc_data = {
 static struct at91_mmc_data __initdata eco920_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 0,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct physmap_flash_data eco920_flash_data = {

arch/arm/mach-at91/board-flexibity.c

@@ -52,12 +52,14 @@ static void __init flexibity_init_early(void)
 /* USB Host port */
 static struct at91_usbh_data __initdata flexibity_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /* USB Device port */
 static struct at91_udc_data __initdata flexibity_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /* SPI devices */
@@ -76,6 +78,7 @@ static struct at91_mmc_data __initdata flexibity_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
 	.wp_pin		= AT91_PIN_PC4,
+	.vcc_pin	= -EINVAL,
 };
 
 /* LEDs */

arch/arm/mach-at91/board-foxg20.c

@@ -106,6 +106,8 @@ static void __init foxg20_init_early(void)
  */
 static struct at91_usbh_data __initdata foxg20_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -113,7 +115,7 @@ static struct at91_usbh_data __initdata foxg20_usbh_data = {
  */
 static struct at91_udc_data __initdata foxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC6,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -147,6 +149,9 @@ static struct macb_platform_data __initdata foxg20_macb_data = {
 static struct at91_mmc_data __initdata foxg20_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-gsia18s.c

@@ -80,6 +80,8 @@ static void __init gsia18s_init_early(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -87,7 +89,7 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
@@ -530,6 +532,7 @@ static struct i2c_board_info __initdata gsia18s_i2c_devices[] = {
 static struct at91_cf_data __initdata gsia18s_cf1_data = {
 	.irq_pin	= AT91_PIN_PA27,
 	.det_pin	= AT91_PIN_PB30,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PB31,
 	.chipselect	= 5,
 	.flags		= AT91_CF_TRUE_IDE,

arch/arm/mach-at91/board-kafa.c

@@ -68,6 +68,8 @@ static struct macb_platform_data __initdata kafa_eth_data = {
 
 static struct at91_usbh_data __initdata kafa_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kafa_udc_data = {

arch/arm/mach-at91/board-kb9202.c

@@ -76,6 +76,8 @@ static struct macb_platform_data __initdata kb9202_eth_data = {
 
 static struct at91_usbh_data __initdata kb9202_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata kb9202_udc_data = {
@@ -87,6 +89,8 @@ static struct at91_mmc_data __initdata kb9202_mmc_data = {
 	.det_pin	= AT91_PIN_PB2,
 	.slot_b		= 0,
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 static struct mtd_partition __initdata kb9202_nand_partition[] = {
@@ -100,7 +104,7 @@ static struct mtd_partition __initdata kb9202_nand_partition[] = {
 static struct atmel_nand_data __initdata kb9202_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-	// .det_pin	= ... not there
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC29,
 	.enable_pin	= AT91_PIN_PC28,
 	.parts		= kb9202_nand_partition,

arch/arm/mach-at91/board-neocore926.c

@@ -72,6 +72,7 @@ static void __init neocore926_init_early(void)
 static struct at91_usbh_data __initdata neocore926_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +80,7 @@ static struct at91_usbh_data __initdata neocore926_usbh_data = {
  */
 static struct at91_udc_data __initdata neocore926_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -149,6 +150,7 @@ static struct at91_mmc_data __initdata neocore926_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -190,6 +192,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = {
 	.enable_pin		= AT91_PIN_PD15,
 	.parts			= neocore926_nand_partition,
 	.num_parts		= ARRAY_SIZE(neocore926_nand_partition),
+	.det_pin		= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata neocore926_nand_smc_config = {

arch/arm/mach-at91/board-pcontrol-g20.c

@@ -107,6 +107,8 @@ static void __init add_device_pcontrol(void)
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 

arch/arm/mach-at91/board-picotux200.c

@@ -67,6 +67,8 @@ static struct macb_platform_data __initdata picotux200_eth_data = {
 
 static struct at91_usbh_data __initdata picotux200_usbh_data = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_mmc_data __initdata picotux200_mmc_data = {
@@ -74,6 +76,7 @@ static struct at91_mmc_data __initdata picotux200_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 
 #define PICOTUX200_FLASH_BASE	AT91_CHIPSELECT_0

arch/arm/mach-at91/board-qil-a9260.c

@@ -77,6 +77,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -84,7 +86,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 /*
@@ -133,7 +135,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -172,9 +174,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*

arch/arm/mach-at91/board-rm9200dk.c

@@ -72,6 +72,8 @@ static struct macb_platform_data __initdata dk_eth_data = {
 
 static struct at91_usbh_data __initdata dk_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata dk_udc_data = {
@@ -80,16 +82,19 @@ static struct at91_udc_data __initdata dk_udc_data = {
 };
 
 static struct at91_cf_data __initdata dk_cf_data = {
+	.irq_pin	= -EINVAL,
 	.det_pin	= AT91_PIN_PB0,
+	.vcc_pin	= -EINVAL,
 	.rst_pin	= AT91_PIN_PC5,
-	// .irq_pin	= ... not connected
-	// .vcc_pin	= ... always powered
 };
 
 #ifndef CONFIG_MTD_AT91_DATAFLASH_CARD
 static struct at91_mmc_data __initdata dk_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -143,7 +148,7 @@ static struct atmel_nand_data __initdata dk_nand_data = {
 	.cle		= 21,
 	.det_pin	= AT91_PIN_PB1,
 	.rdy_pin	= AT91_PIN_PC2,
-	// .enable_pin	= ... not there
+	.enable_pin	= -EINVAL,
 	.parts		= dk_nand_partition,
 	.num_parts	= ARRAY_SIZE(dk_nand_partition),
 };

arch/arm/mach-at91/board-rm9200ek.c

@@ -72,6 +72,8 @@ static struct macb_platform_data __initdata ek_eth_data = {
 
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata ek_udc_data = {
@@ -85,6 +87,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
 	.wp_pin		= AT91_PIN_PA17,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 

arch/arm/mach-at91/board-rsi-ews.c

@@ -70,6 +70,8 @@ static struct macb_platform_data rsi_ews_eth_data __initdata = {
  */
 static struct at91_usbh_data rsi_ews_usbh_data __initdata = {
 	.ports		= 1,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*

arch/arm/mach-at91/board-sam9-l9260.c

@@ -72,6 +72,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -79,7 +81,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -134,7 +136,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -176,7 +178,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC8,
 	.wp_pin		= AT91_PIN_PC4,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 static void __init ek_board_init(void)

arch/arm/mach-at91/board-sam9260ek.c

@@ -75,6 +75,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -82,7 +84,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -176,7 +178,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -223,9 +225,9 @@ static void __init ek_add_device_nand(void)
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,
 	.wire4		= 1,
-//	.det_pin	= ... not connected
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9261ek.c

@@ -151,6 +151,8 @@ static void __init ek_add_device_dm9000(void) {}
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -159,7 +161,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB29,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -182,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 22,
 	.cle		= 21,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC15,
 	.enable_pin	= AT91_PIN_PC14,
 	.parts		= ek_nand_partition,
@@ -345,6 +347,9 @@ static struct spi_board_info ek_spi_devices[] = {
  */
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 #endif /* CONFIG_SPI_ATMEL_* */

arch/arm/mach-at91/board-sam9263ek.c

@@ -74,6 +74,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
 	.vbus_pin	= { AT91_PIN_PA24, AT91_PIN_PA21 },
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -81,7 +82,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PA25,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -151,7 +152,7 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PE18,
 	.wp_pin		= AT91_PIN_PE19,
-//	.vcc_pin	= ... not connected
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -183,7 +184,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,
@@ -353,6 +354,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9g20ek.c

@@ -86,6 +86,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -93,7 +95,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PC5,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 
@@ -163,6 +165,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -210,6 +213,7 @@ static struct mci_platform_data __initdata ek_mmc_data = {
 	.slot[1] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PC9,
+		.wp_pin		= -EINVAL,
 	},
 
 };
@@ -218,6 +222,8 @@ static struct at91_mmc_data __initdata ek_mmc_data = {
 	.slot_b		= 1,	/* Only one slot so use slot B */
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PC9,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -227,6 +233,7 @@ static void __init ek_add_device_mmc(void)
 	if (ek_have_2mmc()) {
 		ek_mmc_data.slot[0].bus_width = 4;
 		ek_mmc_data.slot[0].detect_pin = AT91_PIN_PC2;
+		ek_mmc_data.slot[0].wp_pin = -1;
 	}
 	at91_add_device_mci(0, &ek_mmc_data);
 #else

arch/arm/mach-at91/board-sam9m10g45ek.c

@@ -69,6 +69,7 @@ static void __init ek_init_early(void)
 static struct at91_usbh_data __initdata ek_usbh_hs_data = {
 	.ports		= 2,
 	.vbus_pin	= {AT91_PIN_PD1, AT91_PIN_PD3},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -100,6 +101,7 @@ static struct mci_platform_data __initdata mci0_data = {
 	.slot[0] = {
 		.bus_width	= 4,
 		.detect_pin	= AT91_PIN_PD10,
+		.wp_pin		= -EINVAL,
 	},
 };
 
@@ -143,6 +145,7 @@ static struct atmel_nand_data __initdata ek_nand_data = {
 	.cle		= 22,
 	.rdy_pin	= AT91_PIN_PC8,
 	.enable_pin	= AT91_PIN_PC14,
+	.det_pin	= -EINVAL,
 	.parts		= ek_nand_partition,
 	.num_parts	= ARRAY_SIZE(ek_nand_partition),
 };
@@ -330,6 +333,7 @@ static void __init ek_add_device_buttons(void) {}
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-sam9rlek.c

@@ -67,8 +67,8 @@ static struct usba_platform_data __initdata ek_usba_udc_data = {
 static struct at91_mmc_data __initdata ek_mmc_data = {
 	.wire4		= 1,
 	.det_pin	= AT91_PIN_PA15,
-//	.wp_pin		= ... not connected
-//	.vcc_pin	= ... not connected
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 
@@ -91,7 +91,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PD17,
 	.enable_pin	= AT91_PIN_PB6,
 	.parts		= ek_nand_partition,
@@ -204,6 +204,7 @@ static struct atmel_lcdfb_info __initdata ek_lcdc_data;
  * reset_pin is not connected: NRST
  */
 static struct ac97c_platform_data ek_ac97_data = {
+	.reset_pin	= -EINVAL,
 };
 
 

arch/arm/mach-at91/board-snapper9260.c

@@ -57,15 +57,19 @@ static void __init snapper9260_init_early(void)
 
 static struct at91_usbh_data __initdata snapper9260_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 static struct at91_udc_data __initdata snapper9260_udc_data = {
 	.vbus_pin		= SNAPPER9260_IO_EXP_GPIO(5),
 	.vbus_active_low	= 1,
 	.vbus_polled		= 1,
+	.pullup_pin		= -EINVAL,
 };
 
 static struct macb_platform_data snapper9260_macb_data = {
+	.phy_irq_pin	= -EINVAL,
 	.is_rmii	= 1,
 };
 
@@ -104,6 +108,8 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = {
 	.parts		= snapper9260_nand_partitions,
 	.num_parts	= ARRAY_SIZE(snapper9260_nand_partitions),
 	.bus_width_16	= 0,
+	.enable_pin	= -EINVAL,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata snapper9260_nand_smc_config = {

arch/arm/mach-at91/board-stamp9g20.c

@@ -85,6 +85,7 @@ static struct atmel_nand_data __initdata nand_data = {
 	.rdy_pin	= AT91_PIN_PC13,
 	.enable_pin	= AT91_PIN_PC14,
 	.bus_width_16	= 0,
+	.det_pin	= -EINVAL,
 };
 
 static struct sam9_smc_config __initdata nand_smc_config = {
@@ -122,12 +123,17 @@ static void __init add_device_nand(void)
 static struct mci_platform_data __initdata mmc_data = {
 	.slot[0] = {
 		.bus_width	= 4,
+		.detect_pin	= -1;
+		.wp_pin		= -1;
 	},
 };
 #else
 static struct at91_mmc_data __initdata mmc_data = {
 	.slot_b		= 0,
 	.wire4		= 1,
+	.det_pin	= -EINVAL,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 #endif
 
@@ -137,6 +143,8 @@ static struct at91_mmc_data __initdata mmc_data = {
  */
 static struct at91_usbh_data __initdata usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 
@@ -145,12 +153,12 @@ static struct at91_usbh_data __initdata usbh_data = {
  */
 static struct at91_udc_data __initdata portuxg20_udc_data = {
 	.vbus_pin	= AT91_PIN_PC7,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static struct at91_udc_data __initdata stamp9g20evb_udc_data = {
 	.vbus_pin	= AT91_PIN_PA22,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 

arch/arm/mach-at91/board-usb-a926x.c

@@ -66,6 +66,8 @@ static void __init ek_init_early(void)
  */
 static struct at91_usbh_data __initdata ek_usbh_data = {
 	.ports		= 2,
+	.vbus_pin	= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -73,7 +75,7 @@ static struct at91_usbh_data __initdata ek_usbh_data = {
  */
 static struct at91_udc_data __initdata ek_udc_data = {
 	.vbus_pin	= AT91_PIN_PB11,
-	.pullup_pin	= 0,		/* pull-up driven by UDC */
+	.pullup_pin	= -EINVAL,		/* pull-up driven by UDC */
 };
 
 static void __init ek_add_device_udc(void)
@@ -193,7 +195,7 @@ static struct mtd_partition __initdata ek_nand_partition[] = {
 static struct atmel_nand_data __initdata ek_nand_data = {
 	.ale		= 21,
 	.cle		= 22,
-//	.det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PA22,
 	.enable_pin	= AT91_PIN_PD15,
 	.parts		= ek_nand_partition,

arch/arm/mach-at91/board-yl-9200.c

@@ -120,6 +120,8 @@ static struct macb_platform_data __initdata yl9200_eth_data = {
  */
 static struct at91_usbh_data __initdata yl9200_usbh_data = {
 	.ports			= 1,	/* PQFP version of AT91RM9200 */
+	.vbus_pin		= {-EINVAL, -EINVAL},
+	.overcurrent_pin= {-EINVAL, -EINVAL},
 };
 
 /*
@@ -137,8 +139,9 @@ static struct at91_udc_data __initdata yl9200_udc_data = {
  */
 static struct at91_mmc_data __initdata yl9200_mmc_data = {
 	.det_pin	= AT91_PIN_PB9,
-	// .wp_pin	= ... not connected
 	.wire4		= 1,
+	.wp_pin		= -EINVAL,
+	.vcc_pin	= -EINVAL,
 };
 
 /*
@@ -175,7 +178,7 @@ static struct mtd_partition __initdata yl9200_nand_partition[] = {
 static struct atmel_nand_data __initdata yl9200_nand_data = {
 	.ale		= 6,
 	.cle		= 7,
-	// .det_pin	= ... not connected
+	.det_pin	= -EINVAL,
 	.rdy_pin	= AT91_PIN_PC14,	/* R/!B (Sheet10) */
 	.enable_pin	= AT91_PIN_PC15,	/* !CE  (Sheet10) */
 	.parts		= yl9200_nand_partition,

arch/arm/mach-at91/include/mach/board.h

@@ -44,10 +44,10 @@
 
  /* USB Device */
 struct at91_udc_data {
-	u8	vbus_pin;		/* high == host powering us */
+	int	vbus_pin;		/* high == host powering us */
 	u8	vbus_active_low;	/* vbus polarity */
 	u8	vbus_polled;		/* Use polling, not interrupt */
-	u8	pullup_pin;		/* active == D+ pulled up */
+	int	pullup_pin;		/* active == D+ pulled up */
 	u8	pullup_active_low;	/* true == pullup_pin is active low */
 };
 extern void __init at91_add_device_udc(struct at91_udc_data *data);
@@ -57,10 +57,10 @@ extern void __init at91_add_device_usba(struct usba_platform_data *data);
 
  /* Compact Flash */
 struct at91_cf_data {
-	u8	irq_pin;		/* I/O IRQ */
-	u8	det_pin;		/* Card detect */
-	u8	vcc_pin;		/* power switching */
-	u8	rst_pin;		/* card reset */
+	int	irq_pin;		/* I/O IRQ */
+	int	det_pin;		/* Card detect */
+	int	vcc_pin;		/* power switching */
+	int	rst_pin;		/* card reset */
 	u8	chipselect;		/* EBI Chip Select number */
 	u8	flags;
 #define AT91_CF_TRUE_IDE	0x01
@@ -71,11 +71,11 @@ extern void __init at91_add_device_cf(struct at91_cf_data *data);
  /* MMC / SD */
   /* at91_mci platform config */
 struct at91_mmc_data {
-	u8		det_pin;	/* card detect IRQ */
+	int		det_pin;	/* card detect IRQ */
 	unsigned	slot_b:1;	/* uses Slot B */
 	unsigned	wire4:1;	/* (SD) supports DAT0..DAT3 */
-	u8		wp_pin;		/* (SD) writeprotect detect */
-	u8		vcc_pin;	/* power switching (high == on) */
+	int		wp_pin;		/* (SD) writeprotect detect */
+	int		vcc_pin;	/* power switching (high == on) */
 };
 extern void __init at91_add_device_mmc(short mmc_id, struct at91_mmc_data *data);
 
@@ -87,10 +87,10 @@ extern void __init at91_add_device_eth(struct macb_platform_data *data);
  /* USB Host */
 struct at91_usbh_data {
 	u8		ports;		/* number of ports on root hub */
-	u8		vbus_pin[2];	/* port power-control pin */
+	int		vbus_pin[2];	/* port power-control pin */
 	u8              vbus_pin_inverted;
 	u8              overcurrent_supported;
-	u8              overcurrent_pin[2];
+	int             overcurrent_pin[2];
 	u8              overcurrent_status[2];
 	u8              overcurrent_changed[2];
 };
@@ -100,9 +100,9 @@ extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data);
 
  /* NAND / SmartMedia */
 struct atmel_nand_data {
-	u8		enable_pin;	/* chip enable */
-	u8		det_pin;	/* card detect */
-	u8		rdy_pin;	/* ready/busy */
+	int		enable_pin;	/* chip enable */
+	int		det_pin;	/* card detect */
+	int		rdy_pin;	/* ready/busy */
 	u8              rdy_pin_active_low;     /* rdy_pin value is inverted */
 	u8		ale;		/* address line number connected to ALE */
 	u8		cle;		/* address line number connected to CLE */

include/linux/platform_data/macb.h

@@ -10,7 +10,7 @@
 
 struct macb_platform_data {
 	u32		phy_mask;
-	u8		phy_irq_pin;	/* PHY IRQ */
+	int		phy_irq_pin;	/* PHY IRQ */
 	u8		is_rmii;	/* using RMII interface? */
 };