MIPS: PCMCIA: new socket driver for Au1000 demoboards.

New PCMCIA socket driver for all Db/Pb1xxx boards (except Pb1000),
which replaces au1000_db1x00.c and (most of) au1000_pb1x00.c.
Notable improvements:
        - supports Db1000, DB/PB1100/1500/1550/1200.
        - support for carddetect and statuschange IRQs.
        - pcmcia socket mem/io/attr areas and irqs passed through
          platform resource information.
        - doesn't freeze system during card insertion/ejection like
          the one it replaces.
        - boardtype is automatically detected using BCSR ID register.

Run-tested on the DB1200.

Cc: Linux-PCMCIA <linux-pcmcia@lists.infradead.org>
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>

arch/mips/alchemy/common/platform.c

@@ -308,11 +308,6 @@ static struct platform_device au1200_mmc1_device = {
 #endif /* #ifndef CONFIG_MIPS_DB1200 */
 #endif /* #ifdef CONFIG_SOC_AU1200 */
 
-static struct platform_device au1x00_pcmcia_device = {
-	.name 		= "au1x00-pcmcia",
-	.id 		= 0,
-};
-
 /* All Alchemy demoboards with I2C have this #define in their headers */
 #ifdef SMBUS_PSC_BASE
 static struct resource pbdb_smbus_resources[] = {
@@ -334,7 +329,6 @@ static struct platform_device pbdb_smbus_device = {
 static struct platform_device *au1xxx_platform_devices[] __initdata = {
 	&au1xx0_uart_device,
 	&au1xxx_usb_ohci_device,
-	&au1x00_pcmcia_device,
 #ifdef CONFIG_FB_AU1100
 	&au1100_lcd_device,
 #endif

arch/mips/alchemy/common/setup.c

@@ -107,7 +107,8 @@ phys_t __fixup_bigphys_addr(phys_t phys_addr, phys_t size)
 	 * The pseudo address we use is 0xF400 0000. Any address over
 	 * 0xF400 0000 is a PCMCIA pseudo address.
 	 */
-	if ((phys_addr >= 0xF4000000) && (phys_addr < 0xFFFFFFFF))
+	if ((phys_addr >= PCMCIA_ATTR_PSEUDO_PHYS) &&
+	    (phys_addr < PCMCIA_PSEUDO_END))
 		return (phys_t)(phys_addr << 4);
 
 	/* default nop */

arch/mips/include/asm/mach-au1x00/au1000.h

@@ -1724,6 +1724,20 @@ enum soc_au1200_ints {
 
 #endif
 
+/*
+ * All Au1xx0 SOCs have a PCMCIA controller.
+ * We setup our 32-bit pseudo addresses to be equal to the
+ * 36-bit addr >> 4, to make it easier to check the address
+ * and fix it.
+ * The PCMCIA socket 0 physical attribute address is 0xF 4000 0000.
+ * The pseudo address we use is 0xF400 0000. Any address over
+ * 0xF400 0000 is a PCMCIA pseudo address.
+ */
+#define PCMCIA_IO_PSEUDO_PHYS	(PCMCIA_IO_PHYS_ADDR >> 4)
+#define PCMCIA_ATTR_PSEUDO_PHYS	(PCMCIA_ATTR_PHYS_ADDR >> 4)
+#define PCMCIA_MEM_PSEUDO_PHYS	(PCMCIA_MEM_PHYS_ADDR >> 4)
+#define PCMCIA_PSEUDO_END	(0xffffffff)
+
 #ifndef _LANGUAGE_ASSEMBLY
 typedef volatile struct {
 	/* 0x0000 */ u32 toytrim;

drivers/pcmcia/Kconfig

@@ -174,6 +174,17 @@ config PCMCIA_AU1X00
 	tristate "Au1x00 pcmcia support"
 	depends on SOC_AU1X00 && PCMCIA
 
+config PCMCIA_ALCHEMY_DEVBOARD
+	tristate "Alchemy Db/Pb1xxx PCMCIA socket services"
+	depends on SOC_AU1X00 && PCMCIA
+	select 64BIT_PHYS_ADDR
+	help
+	  Enable this driver of you want PCMCIA support on your Alchemy
+	  Db1000, Db/Pb1100, Db/Pb1500, Db/Pb1550, Db/Pb1200 board.
+	  NOT suitable for the PB1000!
+
+	  This driver is also available as a module called db1xxx_ss.ko
+
 config PCMCIA_BCM63XX
 	tristate "bcm63xx pcmcia support"
 	depends on BCM63XX && PCMCIA

drivers/pcmcia/Makefile

@@ -35,17 +35,10 @@ obj-$(CONFIG_OMAP_CF)				+= omap_cf.o
 obj-$(CONFIG_BFIN_CFPCMCIA)			+= bfin_cf_pcmcia.o
 obj-$(CONFIG_AT91_CF)				+= at91_cf.o
 obj-$(CONFIG_ELECTRA_CF)			+= electra_cf.o
+obj-$(CONFIG_PCMCIA_ALCHEMY_DEVBOARD)		+= db1xxx_ss.o
 
 au1x00_ss-y					+= au1000_generic.o
 au1x00_ss-$(CONFIG_MIPS_PB1000)			+= au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1100)			+= au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1200)			+= au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_PB1500)			+= au1000_pb1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1000)			+= au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1100)			+= au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1200)			+= au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1500)			+= au1000_db1x00.o
-au1x00_ss-$(CONFIG_MIPS_DB1550)			+= au1000_db1x00.o
 au1x00_ss-$(CONFIG_MIPS_XXS1500)		+= au1000_xxs1500.o
 
 sa1111_cs-y					+= sa1111_generic.o

drivers/pcmcia/au1000_db1x00.c

-/*
- *
- * Alchemy Semi Db1x00 boards specific pcmcia routines.
- *
- * Copyright 2002 MontaVista Software Inc.
- * Author: MontaVista Software, Inc.
- *         	ppopov@mvista.com or source@mvista.com
- *
- * Copyright 2004 Pete Popov, updated the driver to 2.6.
- * Followed the sa11xx API and largely copied many of the hardware
- * independent functions.
- *
- * ########################################################################
- *
- *  This program is free software; you can distribute it and/or modify it
- *  under the terms of the GNU General Public License (Version 2) as
- *  published by the Free Software Foundation.
- *
- *  This program is distributed in the hope it will be useful, but WITHOUT
- *  ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or
- *  FITNESS FOR A PARTICULAR PURPOSE.  See the GNU General Public License
- *  for more details.
- *
- *  You should have received a copy of the GNU General Public License along
- *  with this program; if not, write to the Free Software Foundation, Inc.,
- *  59 Temple Place - Suite 330, Boston MA 02111-1307, USA.
- *
- * ########################################################################
- *
- *
- */
-
-#include <linux/module.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/interrupt.h>
-#include <linux/device.h>
-#include <linux/init.h>
-
-#include <asm/irq.h>
-#include <asm/signal.h>
-#include <asm/mach-au1x00/au1000.h>
-
-#if defined(CONFIG_MIPS_DB1200)
-	#include <db1200.h>
-#elif defined(CONFIG_MIPS_PB1200)
-	#include <pb1200.h>
-#else
-	#include <asm/mach-db1x00/db1x00.h>
-#endif
-
-#include <asm/mach-db1x00/bcsr.h>
-#include "au1000_generic.h"
-
-#if 0
-#define debug(x,args...) printk(KERN_DEBUG "%s: " x, __func__ , ##args)
-#else
-#define debug(x,args...)
-#endif
-
-
-struct au1000_pcmcia_socket au1000_pcmcia_socket[PCMCIA_NUM_SOCKS];
-extern int au1x00_pcmcia_socket_probe(struct device *, struct pcmcia_low_level *, int, int);
-
-static int db1x00_pcmcia_hw_init(struct au1000_pcmcia_socket *skt)
-{
-#ifdef CONFIG_MIPS_DB1550
-	skt->irq = skt->nr ? AU1000_GPIO_5 : AU1000_GPIO_3;
-#elif defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
-	skt->irq = skt->nr ? BOARD_PC1_INT : BOARD_PC0_INT;
-#else
-	skt->irq = skt->nr ? AU1000_GPIO_5 : AU1000_GPIO_2;
-#endif
-	return 0;
-}
-
-static void db1x00_pcmcia_shutdown(struct au1000_pcmcia_socket *skt)
-{
-	bcsr_write(BCSR_PCMCIA, 0);	/* turn off power */
-	msleep(2);
-}
-
-static void
-db1x00_pcmcia_socket_state(struct au1000_pcmcia_socket *skt, struct pcmcia_state *state)
-{
-	u32 inserted;
-	unsigned char vs;
-
-	state->ready = 0;
-	state->vs_Xv = 0;
-	state->vs_3v = 0;
-	state->detect = 0;
-
-	switch (skt->nr) {
-	case 0:
-		vs = bcsr_read(BCSR_STATUS) & 0x3;
-#if defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
-		inserted = BOARD_CARD_INSERTED(0);
-#else
-		inserted = !(bcsr_read(BCSR_STATUS) & (1 << 4));
-#endif
-		break;
-	case 1:
-		vs = (bcsr_read(BCSR_STATUS) & 0xC) >> 2;
-#if defined(CONFIG_MIPS_DB1200) || defined(CONFIG_MIPS_PB1200)
-		inserted = BOARD_CARD_INSERTED(1);
-#else
-		inserted = !(bcsr_read(BCSR_STATUS) & (1<<5));
-#endif
-		break;
-	default:/* should never happen */
-		return;
-	}
-
-	if (inserted)
-		debug("db1x00 socket %d: inserted %d, vs %d pcmcia %x\n",
-				skt->nr, inserted, vs, bcsr_read(BCSR_PCMCIA));
-
-	if (inserted) {
-		switch (vs) {
-			case 0:
-			case 2:
-				state->vs_3v=1;
-				break;
-			case 3: /* 5V */
-				break;
-			default:
-				/* return without setting 'detect' */
-				printk(KERN_ERR "db1x00 bad VS (%d)\n",
-						vs);
-		}
-		state->detect = 1;
-		state->ready = 1;
-	}
-	else {
-		/* if the card was previously inserted and then ejected,
-		 * we should turn off power to it
-		 */
-		if ((skt->nr == 0) &&
-		    (bcsr_read(BCSR_PCMCIA) & BCSR_PCMCIA_PC0RST)) {
-			bcsr_mod(BCSR_PCMCIA, BCSR_PCMCIA_PC0RST   |
-					      BCSR_PCMCIA_PC0DRVEN |
-					      BCSR_PCMCIA_PC0VPP   |
-					      BCSR_PCMCIA_PC0VCC, 0);
-			msleep(10);
-		}
-		else if ((skt->nr == 1) &&
-			 (bcsr_read(BCSR_PCMCIA) & BCSR_PCMCIA_PC1RST)) {
-			bcsr_mod(BCSR_PCMCIA, BCSR_PCMCIA_PC1RST   |
-					      BCSR_PCMCIA_PC1DRVEN |
-					      BCSR_PCMCIA_PC1VPP   |
-					      BCSR_PCMCIA_PC1VCC, 0);
-			msleep(10);
-		}
-	}
-
-	state->bvd1=1;
-	state->bvd2=1;
-	state->wrprot=0;
-}
-
-static int
-db1x00_pcmcia_configure_socket(struct au1000_pcmcia_socket *skt, struct socket_state_t *state)
-{
-	u16 pwr;
-	int sock = skt->nr;
-
-	debug("config_skt %d Vcc %dV Vpp %dV, reset %d\n",
-			sock, state->Vcc, state->Vpp,
-			state->flags & SS_RESET);
-
-	/* pcmcia reg was set to zero at init time. Be careful when
-	 * initializing a socket not to wipe out the settings of the
-	 * other socket.
-	 */
-	pwr = bcsr_read(BCSR_PCMCIA);
-	pwr &= ~(0xf << sock*8); /* clear voltage settings */
-
-	state->Vpp = 0;
-	switch(state->Vcc){
-		case 0:  /* Vcc 0 */
-			pwr |= SET_VCC_VPP(0,0,sock);
-			break;
-		case 50: /* Vcc 5V */
-			switch(state->Vpp) {
-				case 0:
-					pwr |= SET_VCC_VPP(2,0,sock);
-					break;
-				case 50:
-					pwr |= SET_VCC_VPP(2,1,sock);
-					break;
-				case 12:
-					pwr |= SET_VCC_VPP(2,2,sock);
-					break;
-				case 33:
-				default:
-					pwr |= SET_VCC_VPP(0,0,sock);
-					printk("%s: bad Vcc/Vpp (%d:%d)\n",
-							__func__,
-							state->Vcc,
-							state->Vpp);
-					break;
-			}
-			break;
-		case 33: /* Vcc 3.3V */
-			switch(state->Vpp) {
-				case 0:
-					pwr |= SET_VCC_VPP(1,0,sock);
-					break;
-				case 12:
-					pwr |= SET_VCC_VPP(1,2,sock);
-					break;
-				case 33:
-					pwr |= SET_VCC_VPP(1,1,sock);
-					break;
-				case 50:
-				default:
-					pwr |= SET_VCC_VPP(0,0,sock);
-					printk("%s: bad Vcc/Vpp (%d:%d)\n",
-							__func__,
-							state->Vcc,
-							state->Vpp);
-					break;
-			}
-			break;
-		default: /* what's this ? */
-			pwr |= SET_VCC_VPP(0,0,sock);
-			printk(KERN_ERR "%s: bad Vcc %d\n",
-					__func__, state->Vcc);
-			break;
-	}
-
-	bcsr_write(BCSR_PCMCIA, pwr);
-	msleep(300);
-
-	if (sock == 0) {
-		if (!(state->flags & SS_RESET)) {
-			pwr |= BCSR_PCMCIA_PC0DRVEN;
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(300);
-			pwr |= BCSR_PCMCIA_PC0RST;
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(100);
-		}
-		else {
-			pwr &= ~(BCSR_PCMCIA_PC0RST | BCSR_PCMCIA_PC0DRVEN);
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(100);
-		}
-	}
-	else {
-		if (!(state->flags & SS_RESET)) {
-			pwr |= BCSR_PCMCIA_PC1DRVEN;
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(300);
-			pwr |= BCSR_PCMCIA_PC1RST;
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(100);
-		}
-		else {
-			pwr &= ~(BCSR_PCMCIA_PC1RST | BCSR_PCMCIA_PC1DRVEN);
-			bcsr_write(BCSR_PCMCIA, pwr);
-			msleep(100);
-		}
-	}
-	return 0;
-}
-
-/*
- * Enable card status IRQs on (re-)initialisation.  This can
- * be called at initialisation, power management event, or
- * pcmcia event.
- */
-void db1x00_socket_init(struct au1000_pcmcia_socket *skt)
-{
-	/* nothing to do for now */
-}
-
-/*
- * Disable card status IRQs and PCMCIA bus on suspend.
- */
-void db1x00_socket_suspend(struct au1000_pcmcia_socket *skt)
-{
-	/* nothing to do for now */
-}
-
-struct pcmcia_low_level db1x00_pcmcia_ops = {
-	.owner			= THIS_MODULE,
-
-	.hw_init 		= db1x00_pcmcia_hw_init,
-	.hw_shutdown		= db1x00_pcmcia_shutdown,
-
-	.socket_state		= db1x00_pcmcia_socket_state,
-	.configure_socket	= db1x00_pcmcia_configure_socket,
-
-	.socket_init		= db1x00_socket_init,
-	.socket_suspend		= db1x00_socket_suspend
-};
-
-int au1x_board_init(struct device *dev)
-{
-	int ret = -ENODEV;
-	bcsr_write(BCSR_PCMCIA, 0); /* turn off power, if it's not already off */
-	msleep(2);
-	ret = au1x00_pcmcia_socket_probe(dev, &db1x00_pcmcia_ops, 0, 2);
-	return ret;
-}

drivers/pcmcia/au1000_generic.h

@@ -44,22 +44,12 @@
 /* pcmcia socket 1 needs external glue logic so the memory map
  * differs from board to board.
  */
-#if defined(CONFIG_MIPS_PB1000) || defined(CONFIG_MIPS_PB1100) || \
-    defined(CONFIG_MIPS_PB1500) || defined(CONFIG_MIPS_PB1550) || \
-    defined(CONFIG_MIPS_PB1200)
+#if defined(CONFIG_MIPS_PB1000)
 #define AU1X_SOCK1_IO        0xF08000000ULL
 #define AU1X_SOCK1_PHYS_ATTR 0xF48000000ULL
 #define AU1X_SOCK1_PHYS_MEM  0xF88000000ULL
 #define AU1X_SOCK1_PSEUDO_PHYS_ATTR 0xF4800000
 #define AU1X_SOCK1_PSEUDO_PHYS_MEM  0xF8800000
-#elif defined(CONFIG_MIPS_DB1000) || defined(CONFIG_MIPS_DB1100) || \
-      defined(CONFIG_MIPS_DB1500) || defined(CONFIG_MIPS_DB1550) || \
-      defined(CONFIG_MIPS_DB1200)
-#define AU1X_SOCK1_IO        0xF04000000ULL
-#define AU1X_SOCK1_PHYS_ATTR 0xF44000000ULL
-#define AU1X_SOCK1_PHYS_MEM  0xF84000000ULL
-#define AU1X_SOCK1_PSEUDO_PHYS_ATTR 0xF4400000
-#define AU1X_SOCK1_PSEUDO_PHYS_MEM  0xF8400000
 #endif
 
 struct pcmcia_state {

drivers/pcmcia/au1000_pb1x00.c

 /*
  *
- * Alchemy Semi Pb1x00 boards specific pcmcia routines.
+ * Alchemy Semi Pb1000 boards specific pcmcia routines.
  *
  * Copyright 2002 MontaVista Software Inc.
  * Author: MontaVista Software, Inc.
@@ -46,20 +46,11 @@
 
 #define debug(fmt, arg...) do { } while (0)
 
-#ifdef CONFIG_MIPS_PB1000
 #include <asm/pb1000.h>
 #define PCMCIA_IRQ AU1000_GPIO_15
-#elif defined (CONFIG_MIPS_PB1500)
-#include <asm/pb1500.h>
-#define PCMCIA_IRQ AU1500_GPIO_203
-#elif defined (CONFIG_MIPS_PB1100)
-#include <asm/pb1100.h>
-#define PCMCIA_IRQ AU1000_GPIO_11
-#endif
 
 static int pb1x00_pcmcia_init(struct pcmcia_init *init)
 {
-#ifdef CONFIG_MIPS_PB1000
 	u16 pcr;
 	pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
 
@@ -74,21 +65,10 @@ static int pb1x00_pcmcia_init(struct pcmcia_init *init)
 	au_sync_delay(20);
 	  
 	return PCMCIA_NUM_SOCKS;
-
-#else /* fixme -- take care of the Pb1500 at some point */
-
-	u16 pcr;
-	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
-	pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
-	au_writew(pcr, PCMCIA_BOARD_REG);
-	au_sync_delay(500);
-	return PCMCIA_NUM_SOCKS;
-#endif
 }
 
 static int pb1x00_pcmcia_shutdown(void)
 {
-#ifdef CONFIG_MIPS_PB1000
 	u16 pcr;
 	pcr = PCR_SLOT_0_RST | PCR_SLOT_1_RST;
 	pcr |= SET_VCC_VPP(VCC_HIZ,VPP_HIZ,0);
@@ -96,14 +76,6 @@ static int pb1x00_pcmcia_shutdown(void)
 	au_writel(pcr, PB1000_PCR);
 	au_sync_delay(20);
 	return 0;
-#else
-	u16 pcr;
-	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf; /* turn off power */
-	pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
-	au_writew(pcr, PCMCIA_BOARD_REG);
-	au_sync_delay(2);
-	return 0;
-#endif
 }
 
 static int 
@@ -112,21 +84,11 @@ pb1x00_pcmcia_socket_state(unsigned sock, struct pcmcia_state *state)
 	u32 inserted0, inserted1;
 	u16 vs0, vs1;
 
-#ifdef CONFIG_MIPS_PB1000
 	vs0 = vs1 = (u16)au_readl(PB1000_ACR1);
 	inserted0 = !(vs0 & (ACR1_SLOT_0_CD1 | ACR1_SLOT_0_CD2));
 	inserted1 = !(vs1 & (ACR1_SLOT_1_CD1 | ACR1_SLOT_1_CD2));
 	vs0 = (vs0 >> 4) & 0x3;
 	vs1 = (vs1 >> 12) & 0x3;
-#else
-	vs0 = (au_readw(BOARD_STATUS_REG) >> 4) & 0x3;
-#ifdef CONFIG_MIPS_PB1500
-	inserted0 = !((au_readl(GPIO2_PINSTATE) >> 1) & 0x1); /* gpio 201 */
-#else /* Pb1100 */
-	inserted0 = !((au_readl(SYS_PINSTATERD) >> 9) & 0x1); /* gpio 9 */
-#endif
-	inserted1 = 0;
-#endif
 
 	state->ready = 0;
 	state->vs_Xv = 0;
@@ -203,7 +165,6 @@ pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
 
 	if(configure->sock > PCMCIA_MAX_SOCK) return -1;
 
-#ifdef CONFIG_MIPS_PB1000
 	pcr = au_readl(PB1000_PCR);
 
 	if (configure->sock == 0) {
@@ -323,84 +284,6 @@ pb1x00_pcmcia_configure_socket(const struct pcmcia_configure *configure)
 	au_writel(pcr, PB1000_PCR);
 	au_sync_delay(300);
 
-#else
-
-	pcr = au_readw(PCMCIA_BOARD_REG) & ~0xf;
-
-	debug("Vcc %dV Vpp %dV, pcr %x, reset %d\n", 
-			configure->vcc, configure->vpp, pcr, configure->reset);
-
-
-	switch(configure->vcc){
-		case 0:  /* Vcc 0 */
-			pcr |= SET_VCC_VPP(0,0);
-			break;
-		case 50: /* Vcc 5V */
-			switch(configure->vpp) {
-				case 0:
-					pcr |= SET_VCC_VPP(2,0);
-					break;
-				case 50:
-					pcr |= SET_VCC_VPP(2,1);
-					break;
-				case 12:
-					pcr |= SET_VCC_VPP(2,2);
-					break;
-				case 33:
-				default:
-					pcr |= SET_VCC_VPP(0,0);
-					printk("%s: bad Vcc/Vpp (%d:%d)\n", 
-							__func__,
-							configure->vcc, 
-							configure->vpp);
-					break;
-			}
-			break;
-		case 33: /* Vcc 3.3V */
-			switch(configure->vpp) {
-				case 0:
-					pcr |= SET_VCC_VPP(1,0);
-					break;
-				case 12:
-					pcr |= SET_VCC_VPP(1,2);
-					break;
-				case 33:
-					pcr |= SET_VCC_VPP(1,1);
-					break;
-				case 50:
-				default:
-					pcr |= SET_VCC_VPP(0,0);
-					printk("%s: bad Vcc/Vpp (%d:%d)\n", 
-							__func__,
-							configure->vcc, 
-							configure->vpp);
-					break;
-			}
-			break;
-		default: /* what's this ? */
-			pcr |= SET_VCC_VPP(0,0);
-			printk(KERN_ERR "%s: bad Vcc %d\n", 
-					__func__, configure->vcc);
-			break;
-	}
-
-	au_writew(pcr, PCMCIA_BOARD_REG);
-	au_sync_delay(300);
-
-	if (!configure->reset) {
-		pcr |= PC_DRV_EN;
-		au_writew(pcr, PCMCIA_BOARD_REG);
-		au_sync_delay(100);
-		pcr |= PC_DEASSERT_RST;
-		au_writew(pcr, PCMCIA_BOARD_REG);
-		au_sync_delay(100);
-	}
-	else {
-		pcr &= ~(PC_DEASSERT_RST | PC_DRV_EN);
-		au_writew(pcr, PCMCIA_BOARD_REG);
-		au_sync_delay(100);
-	}
-#endif
 	return 0;
 }