Merge branch 'dwc_ethernet'

Lars Persson says:

====================
dwc_eth_qos: Add support for Synopsys DWC Ethernet QoS

This is a driver supporting version 4.10a of the Synopsys DWC Ethernet QoS
gigabit ethernet controller. The IP has changed significantly compared to the
dwmac1000 so a separate driver is justified.

The IP is highly configurable at synthesis time. This driver has been
developed for a subset of the total available feature set. Currently
it supports:
* TSO
* Checksum offload for RX and TX.
* Energy efficient ethernet.
* GMII phy interface.
* The statistics module.
* Single RX and TX queue.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt

+* Synopsys DWC Ethernet QoS IP version 4.10 driver (GMAC)
+
+
+Required properties:
+- compatible: Should be "snps,dwc-qos-ethernet-4.10"
+- reg: Address and length of the register set for the device
+- clocks: Phandles to the reference clock and the bus clock
+- clock-names: Should be "phy_ref_clk" for the reference clock and "apb_pclk"
+  for the bus clock.
+- interrupt-parent: Should be the phandle for the interrupt controller
+  that services interrupts for this device
+- interrupts: Should contain the core's combined interrupt signal
+- phy-mode: See ethernet.txt file in the same directory
+
+Optional properties:
+- dma-coherent: Present if dma operations are coherent
+- mac-address: See ethernet.txt in the same directory
+- local-mac-address: See ethernet.txt in the same directory
+- snps,en-lpi: If present it enables use of the AXI low-power interface
+- snps,write-requests: Number of write requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,read-requests: Number of read requests that the AXI port can issue.
+  It depends on the SoC configuration.
+- snps,burst-map: Bitmap of allowed AXI burst lengts, with the LSB
+  representing 4, then 8 etc.
+- snps,txpbl: DMA Programmable burst length for the TX DMA
+- snps,rxpbl: DMA Programmable burst length for the RX DMA
+- snps,en-tx-lpi-clockgating: Enable gating of the MAC TX clock during
+  TX low-power mode.
+- phy-handle: See ethernet.txt file in the same directory
+- mdio device tree subnode: When the GMAC has a phy connected to its local
+    mdio, there must be device tree subnode with the following
+    required properties:
+    - compatible: Must be "snps,dwc-qos-ethernet-mdio".
+    - #address-cells: Must be <1>.
+    - #size-cells: Must be <0>.
+
+    For each phy on the mdio bus, there must be a node with the following
+    fields:
+
+    - reg: phy id used to communicate to phy.
+    - device_type: Must be "ethernet-phy".
+    - fixed-mode device tree subnode: see fixed-link.txt in the same directory
+
+Examples:
+ethernet2@40010000 {
+	clock-names = "phy_ref_clk", "apb_pclk";
+	clocks = <&clkc 17>, <&clkc 15>;
+	compatible = "snps,dwc-qos-ethernet-4.10";
+	interrupt-parent = <&intc>;
+	interrupts = <0x0 0x1e 0x4>;
+	reg = <0x40010000 0x4000>;
+	phy-handle = <&phy2>;
+	phy-mode = "gmii";
+
+	snps,en-tx-lpi-clockgating;
+	snps,en-lpi;
+	snps,write-requests = <2>;
+	snps,read-requests = <16>;
+	snps,burst-map = <0x7>;
+	snps,txpbl = <8>;
+	snps,rxpbl = <2>;
+
+	dma-coherent;
+
+	mdio {
+		#address-cells = <0x1>;
+		#size-cells = <0x0>;
+		phy2: phy@1 {
+			compatible = "ethernet-phy-ieee802.3-c22";
+			device_type = "ethernet-phy";
+			reg = <0x1>;
+		};
+	};
+};

MAINTAINERS

@@ -8903,6 +8903,13 @@ F:	include/linux/dma/dw.h
 F:	include/linux/platform_data/dma-dw.h
 F:	drivers/dma/dw/
 
+SYNOPSYS DESIGNWARE ETHERNET QOS 4.10a driver
+M: Lars Persson <lars.persson@axis.com>
+L: netdev@vger.kernel.org
+S: Supported
+F: Documentation/devicetree/bindings/net/snps,dwc-qos-ethernet.txt
+F: drivers/net/ethernet/synopsys/dwc_eth_qos.c
+
 SYNOPSYS DESIGNWARE MMC/SD/SDIO DRIVER
 M:	Seungwon Jeon <tgih.jun@samsung.com>
 M:	Jaehoon Chung <jh80.chung@samsung.com>

drivers/net/ethernet/Kconfig

@@ -167,6 +167,7 @@ source "drivers/net/ethernet/sgi/Kconfig"
 source "drivers/net/ethernet/smsc/Kconfig"
 source "drivers/net/ethernet/stmicro/Kconfig"
 source "drivers/net/ethernet/sun/Kconfig"
+source "drivers/net/ethernet/synopsys/Kconfig"
 source "drivers/net/ethernet/tehuti/Kconfig"
 source "drivers/net/ethernet/ti/Kconfig"
 source "drivers/net/ethernet/tile/Kconfig"

drivers/net/ethernet/Makefile

@@ -77,6 +77,7 @@ obj-$(CONFIG_NET_VENDOR_SGI) += sgi/
 obj-$(CONFIG_NET_VENDOR_SMSC) += smsc/
 obj-$(CONFIG_NET_VENDOR_STMICRO) += stmicro/
 obj-$(CONFIG_NET_VENDOR_SUN) += sun/
+obj-$(CONFIG_NET_VENDOR_SYNOPSYS) += synopsys/
 obj-$(CONFIG_NET_VENDOR_TEHUTI) += tehuti/
 obj-$(CONFIG_NET_VENDOR_TI) += ti/
 obj-$(CONFIG_TILE_NET) += tile/

drivers/net/ethernet/synopsys/Kconfig

+#
+# Synopsys network device configuration
+#
+
+config NET_VENDOR_SYNOPSYS
+	bool "Synopsys devices"
+	default y
+	---help---
+	  If you have a network (Ethernet) device belonging to this class, say Y.
+
+	  Note that the answer to this question doesn't directly affect the
+	  kernel: saying N will just cause the configurator to skip all
+	  the questions about Synopsys devices. If you say Y, you will be asked
+	  for your specific device in the following questions.
+
+if NET_VENDOR_SYNOPSYS
+
+config SYNOPSYS_DWC_ETH_QOS
+	tristate "Sypnopsys DWC Ethernet QOS v4.10a support"
+	select PHYLIB
+	select CRC32
+	select MII
+	depends on OF
+	---help---
+	  This driver supports the DWC Ethernet QoS from Synopsys
+
+endif # NET_VENDOR_SYNOPSYS

drivers/net/ethernet/synopsys/Makefile

+#
+# Makefile for the Synopsys network device drivers.
+#
+
+obj-$(CONFIG_SYNOPSYS_DWC_ETH_QOS) += dwc_eth_qos.o