mtd: nand: Clarify Kconfig entry for software BCH ECC algorithm

There is no point in having two distinct entries, merge them and
rename the symbol for more clarity: MTD_NAND_ECC_SW_BCH
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>

arch/arm/configs/omap2plus_defconfig

@@ -144,7 +144,7 @@ CONFIG_MTD_ONENAND=y
 CONFIG_MTD_ONENAND_VERIFY_WRITE=y
 CONFIG_MTD_ONENAND_OMAP2=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ECC_BCH=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
 CONFIG_MTD_NAND_OMAP2=y
 CONFIG_MTD_NAND_OMAP_BCH=y
 CONFIG_MTD_SPI_NOR=m

arch/arm/configs/pxa_defconfig

@@ -186,7 +186,7 @@ CONFIG_MTD_M25P80=m
 CONFIG_MTD_BLOCK2MTD=y
 CONFIG_MTD_DOCG3=m
 CONFIG_MTD_NAND=m
-CONFIG_MTD_NAND_ECC_BCH=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
 CONFIG_MTD_NAND_GPIO=m
 CONFIG_MTD_NAND_DISKONCHIP=m
 CONFIG_MTD_NAND_DISKONCHIP_PROBE_ADVANCED=y

arch/mips/configs/db1xxx_defconfig

@@ -96,7 +96,7 @@ CONFIG_MTD_PHYSMAP=y
 CONFIG_MTD_M25P80=y
 CONFIG_MTD_SST25L=y
 CONFIG_MTD_NAND=y
-CONFIG_MTD_NAND_ECC_BCH=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
 CONFIG_MTD_NAND_AU1550=y
 CONFIG_MTD_NAND_PLATFORM=y
 CONFIG_MTD_SPI_NOR=y

arch/mips/configs/generic/board-ni169445.config

@@ -16,7 +16,7 @@ CONFIG_MTD_BLOCK=y
 CONFIG_MTD_CMDLINE_PARTS=y
 
 CONFIG_MTD_NAND_ECC=y
-CONFIG_MTD_NAND_ECC_BCH=y
+CONFIG_MTD_NAND_ECC_SW_BCH=y
 CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_GPIO=y
 CONFIG_MTD_NAND_IDS=y

drivers/mtd/devices/Kconfig

@@ -207,7 +207,7 @@ comment "Disk-On-Chip Device Drivers"
 config MTD_DOCG3
 	tristate "M-Systems Disk-On-Chip G3"
 	select BCH
-	select BCH_CONST_PARAMS if !MTD_NAND_BCH
+	select BCH_CONST_PARAMS if !MTD_NAND_ECC_SW_BCH
 	select BITREVERSE
 	help
 	  This provides an MTD device driver for the M-Systems DiskOnChip

drivers/mtd/nand/raw/Kconfig

@@ -22,14 +22,9 @@ menuconfig MTD_NAND
 
 if MTD_NAND
 
-config MTD_NAND_BCH
-	tristate
+config MTD_NAND_ECC_SW_BCH
+	tristate "Support software BCH ECC"
 	select BCH
-	depends on MTD_NAND_ECC_BCH
-	default MTD_NAND
-
-config MTD_NAND_ECC_BCH
-	bool "Support software BCH ECC"
 	default n
 	help
 	  This enables support for software BCH error correction. Binary BCH

drivers/mtd/nand/raw/Makefile

@@ -2,7 +2,7 @@
 
 obj-$(CONFIG_MTD_NAND)			+= nand.o
 obj-$(CONFIG_MTD_NAND_ECC)		+= nand_ecc.o
-obj-$(CONFIG_MTD_NAND_BCH)		+= nand_bch.o
+obj-$(CONFIG_MTD_NAND_ECC_SW_BCH)	+= nand_bch.o
 obj-$(CONFIG_MTD_SM_COMMON) 		+= sm_common.o
 
 obj-$(CONFIG_MTD_NAND_CAFE)		+= cafe_nand.o

drivers/mtd/nand/raw/nand_base.c

@@ -5087,7 +5087,7 @@ static int nand_set_ecc_soft_ops(struct nand_chip *chip)
 		return 0;
 	case NAND_ECC_BCH:
 		if (!mtd_nand_has_bch()) {
-			WARN(1, "CONFIG_MTD_NAND_ECC_BCH not enabled\n");
+			WARN(1, "CONFIG_MTD_NAND_ECC_SW_BCH not enabled\n");
 			return -EINVAL;
 		}
 		ecc->calculate = nand_bch_calculate_ecc;

drivers/mtd/nand/raw/omap2.c

@@ -1725,9 +1725,9 @@ static bool omap2_nand_ecc_check(struct omap_nand_info *info)
 		break;
 	}
 
-	if (ecc_needs_bch && !IS_ENABLED(CONFIG_MTD_NAND_ECC_BCH)) {
+	if (ecc_needs_bch && !IS_ENABLED(CONFIG_MTD_NAND_ECC_SW_BCH)) {
 		dev_err(&info->pdev->dev,
-			"CONFIG_MTD_NAND_ECC_BCH not enabled\n");
+			"CONFIG_MTD_NAND_ECC_SW_BCH not enabled\n");
 		return false;
 	}
 	if (ecc_needs_omap_bch && !IS_ENABLED(CONFIG_MTD_NAND_OMAP_BCH)) {

include/linux/mtd/nand_bch.h

@@ -15,7 +15,7 @@ struct mtd_info;
 struct nand_chip;
 struct nand_bch_control;
 
-#if defined(CONFIG_MTD_NAND_ECC_BCH)
+#if IS_ENABLED(CONFIG_MTD_NAND_ECC_SW_BCH)
 
 static inline int mtd_nand_has_bch(void) { return 1; }
 
@@ -39,7 +39,7 @@ struct nand_bch_control *nand_bch_init(struct mtd_info *mtd);
  */
 void nand_bch_free(struct nand_bch_control *nbc);
 
-#else /* !CONFIG_MTD_NAND_ECC_BCH */
+#else /* !CONFIG_MTD_NAND_ECC_SW_BCH */
 
 static inline int mtd_nand_has_bch(void) { return 0; }
 
@@ -64,6 +64,6 @@ static inline struct nand_bch_control *nand_bch_init(struct mtd_info *mtd)
 
 static inline void nand_bch_free(struct nand_bch_control *nbc) {}
 
-#endif /* CONFIG_MTD_NAND_ECC_BCH */
+#endif /* CONFIG_MTD_NAND_ECC_SW_BCH */
 
 #endif /* __MTD_NAND_BCH_H__ */